[PATCH 4.19 00/37] 4.19.121-rc1 review

[PATCH 4.19 00/37] 4.19.121-rc1 review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 4.19.121 release.
There are 37 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.121-rc1.gz
or in the git tree and branch at:
	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 4.19.121-rc1

Martin Blumenstingl <martin.blumenstingl@googlemail.com>
    mmc: meson-mx-sdio: remove the broken ->card_busy() op

Martin Blumenstingl <martin.blumenstingl@googlemail.com>
    mmc: meson-mx-sdio: Set MMC_CAP_WAIT_WHILE_BUSY

Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
    mmc: sdhci-msm: Enable host capabilities pertains to R1b response

Adrian Hunter <adrian.hunter@intel.com>
    mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllers

Marek Behún <marek.behun@nic.cz>
    mmc: sdhci-xenon: fix annoying 1.8V regulator warning

Douglas Anderson <dianders@chromium.org>
    mmc: cqhci: Avoid false "cqhci: CQE stuck on" by not open-coding timeout loop

Qu Wenruo <wqu@suse.com>
    btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info

Filipe Manana <fdmanana@suse.com>
    btrfs: fix partial loss of prealloc extent past i_size after fsync

Paul Moore <paul@paul-moore.com>
    selinux: properly handle multiple messages in selinux_netlink_send()

Andy Shevchenko <andriy.shevchenko@linux.intel.com>
    dmaengine: dmatest: Fix iteration non-stop logic

Andreas Gruenbacher <agruenba@redhat.com>
    nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl

Arnd Bergmann <arnd@arndb.de>
    ALSA: opti9xx: shut up gcc-10 range warning

Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
    iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system

David Disseldorp <ddiss@suse.de>
    scsi: target/iblock: fix WRITE SAME zeroing

Tang Bin <tangbin@cmss.chinamobile.com>
    iommu/qcom: Fix local_base status check

Sean Christopherson <sean.j.christopherson@intel.com>
    vfio/type1: Fix VA->PA translation for PFNMAP VMAs in vaddr_get_pfn()

Yan Zhao <yan.y.zhao@intel.com>
    vfio: avoid possible overflow in vfio_iommu_type1_pin_pages

Leon Romanovsky <leon@kernel.org>
    RDMA/core: Fix race between destroy and release FD object

Leon Romanovsky <leon@kernel.org>
    RDMA/core: Prevent mixed use of FDs between shared ufiles

Alaa Hleihel <alaa@mellanox.com>
    RDMA/mlx4: Initialize ib_spec on the stack

Aharon Landau <aharonl@mellanox.com>
    RDMA/mlx5: Set GRH fields in query QP on RoCE

Martin Wilck <mwilck@suse.com>
    scsi: qla2xxx: check UNLOADING before posting async work

Martin Wilck <mwilck@suse.com>
    scsi: qla2xxx: set UNLOADING before waiting for session deletion

Gabriel Krisman Bertazi <krisman@collabora.com>
    dm multipath: use updated MPATHF_QUEUE_IO on mapping for bio-based mpath

Mikulas Patocka <mpatocka@redhat.com>
    dm writecache: fix data corruption when reloading the target

Sunwook Eom <speed.eom@samsung.com>
    dm verity fec: fix hash block number in verity_fec_decode

Dexuan Cui <decui@microsoft.com>
    PM: hibernate: Freeze kernel threads in software_resume()

Kai-Heng Feng <kai.heng.feng@canonical.com>
    PM: ACPI: Output correct message on target power state

Takashi Iwai <tiwai@suse.de>
    ALSA: pcm: oss: Place the plugin buffer overflow checks correctly

Wu Bo <wubo40@huawei.com>
    ALSA: hda/hdmi: fix without unlocked before return

Takashi Iwai <tiwai@suse.de>
    ALSA: usb-audio: Correct a typo of NuPrime DAC-10 USB ID

Hui Wang <hui.wang@canonical.com>
    ALSA: hda/realtek - Two front mics on a Lenovo ThinkCenter

Xiyu Yang <xiyuyang19@fudan.edu.cn>
    btrfs: fix block group leak when removing fails

Vasily Averin <vvs@virtuozzo.com>
    drm/qxl: qxl_release use after free

Vasily Averin <vvs@virtuozzo.com>
    drm/qxl: qxl_release leak in qxl_hw_surface_alloc()

Vasily Averin <vvs@virtuozzo.com>
    drm/qxl: qxl_release leak in qxl_draw_dirty_fb()

Ville Syrjälä <ville.syrjala@linux.intel.com>
    drm/edid: Fix off-by-one in DispID DTD pixel clock


-------------

Diffstat:

 Makefile                            |  4 +--
 drivers/acpi/device_pm.c            |  4 +--
 drivers/dma/dmatest.c               |  4 +--
 drivers/gpu/drm/drm_edid.c          |  2 +-
 drivers/gpu/drm/qxl/qxl_cmd.c       | 10 +++---
 drivers/gpu/drm/qxl/qxl_display.c   |  6 ++--
 drivers/gpu/drm/qxl/qxl_draw.c      | 13 +++----
 drivers/gpu/drm/qxl/qxl_ioctl.c     |  5 +--
 drivers/infiniband/core/rdma_core.c |  4 +--
 drivers/infiniband/hw/mlx4/main.c   |  3 +-
 drivers/infiniband/hw/mlx5/qp.c     |  4 ++-
 drivers/iommu/amd_iommu_init.c      |  2 +-
 drivers/iommu/qcom_iommu.c          |  5 ++-
 drivers/md/dm-mpath.c               |  6 ++--
 drivers/md/dm-verity-fec.c          |  2 +-
 drivers/md/dm-writecache.c          | 52 +++++++++++++++++++--------
 drivers/mmc/host/cqhci.c            | 21 ++++++-----
 drivers/mmc/host/meson-mx-sdio.c    | 11 +-----
 drivers/mmc/host/sdhci-msm.c        |  2 ++
 drivers/mmc/host/sdhci-pci-core.c   |  3 ++
 drivers/mmc/host/sdhci-xenon.c      | 10 ++++++
 drivers/scsi/qla2xxx/qla_os.c       | 35 +++++++++----------
 drivers/target/target_core_iblock.c |  2 +-
 drivers/vfio/vfio_iommu_type1.c     |  6 ++--
 fs/btrfs/extent-tree.c              | 16 +++++----
 fs/btrfs/transaction.c              | 13 +++++--
 fs/btrfs/tree-log.c                 | 43 +++++++++++++++++++++--
 fs/nfs/nfs3acl.c                    | 22 ++++++++----
 kernel/power/hibernate.c            |  7 ++++
 security/selinux/hooks.c            | 70 ++++++++++++++++++++++++-------------
 sound/core/oss/pcm_plugin.c         | 20 ++++++-----
 sound/isa/opti9xx/miro.c            |  9 +++--
 sound/isa/opti9xx/opti92x-ad1848.c  |  9 +++--
 sound/pci/hda/patch_hdmi.c          |  4 ++-
 sound/pci/hda/patch_realtek.c       |  1 +
 sound/usb/quirks.c                  |  2 +-
 36 files changed, 281 insertions(+), 151 deletions(-)

[PATCH 4.19 01/37] drm/edid: Fix off-by-one in DispID DTD pixel clock

[Greg Kroah-Hartman]

From: Ville Syrjälä <ville.syrjala@linux.intel.com>

commit 6292b8efe32e6be408af364132f09572aed14382 upstream.

The DispID DTD pixel clock is documented as:
"00 00 00 h → FF FF FF h | Pixel clock ÷ 10,000 0.01 → 167,772.16 Mega Pixels per Sec"
Which seems to imply that we to add one to the raw value.

Reality seems to agree as there are tiled displays in the wild
which currently show a 10kHz difference in the pixel clock
between the tiles (one tile gets its mode from the base EDID,
the other from the DispID block).

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200423151743.18767-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/drm_edid.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -4706,7 +4706,7 @@ static struct drm_display_mode *drm_mode
 	struct drm_display_mode *mode;
 	unsigned pixel_clock = (timings->pixel_clock[0] |
 				(timings->pixel_clock[1] << 8) |
-				(timings->pixel_clock[2] << 16));
+				(timings->pixel_clock[2] << 16)) + 1;
 	unsigned hactive = (timings->hactive[0] | timings->hactive[1] << 8) + 1;
 	unsigned hblank = (timings->hblank[0] | timings->hblank[1] << 8) + 1;
 	unsigned hsync = (timings->hsync[0] | (timings->hsync[1] & 0x7f) << 8) + 1;

[PATCH 4.19 02/37] drm/qxl: qxl_release leak in qxl_draw_dirty_fb()

[Greg Kroah-Hartman]

From: Vasily Averin <vvs@virtuozzo.com>

commit 85e9b88af1e6164f19ec71381efd5e2bcfc17620 upstream.

ret should be changed to release allocated struct qxl_release

Cc: stable@vger.kernel.org
Fixes: 8002db6336dd ("qxl: convert qxl driver to proper use for reservations")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Link: http://patchwork.freedesktop.org/patch/msgid/22cfd55f-07c8-95d0-a2f7-191b7153c3d4@virtuozzo.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/qxl/qxl_draw.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/drivers/gpu/drm/qxl/qxl_draw.c
+++ b/drivers/gpu/drm/qxl/qxl_draw.c
@@ -348,9 +348,10 @@ void qxl_draw_dirty_fb(struct qxl_device
 		goto out_release_backoff;
 
 	rects = drawable_set_clipping(qdev, num_clips, clips_bo);
-	if (!rects)
+	if (!rects) {
+		ret = -EINVAL;
 		goto out_release_backoff;
-
+	}
 	drawable = (struct qxl_drawable *)qxl_release_map(qdev, release);
 
 	drawable->clip.type = SPICE_CLIP_TYPE_RECTS;

[PATCH 4.19 03/37] drm/qxl: qxl_release leak in qxl_hw_surface_alloc()

[Greg Kroah-Hartman]

From: Vasily Averin <vvs@virtuozzo.com>

commit a65aa9c3676ffccb21361d52fcfedd5b5ff387d7 upstream.

Cc: stable@vger.kernel.org
Fixes: 8002db6336dd ("qxl: convert qxl driver to proper use for reservations")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Link: http://patchwork.freedesktop.org/patch/msgid/2e5a13ae-9ab2-5401-aa4d-03d5f5593423@virtuozzo.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/qxl/qxl_cmd.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/drivers/gpu/drm/qxl/qxl_cmd.c
+++ b/drivers/gpu/drm/qxl/qxl_cmd.c
@@ -472,9 +472,10 @@ int qxl_hw_surface_alloc(struct qxl_devi
 		return ret;
 
 	ret = qxl_release_reserve_list(release, true);
-	if (ret)
+	if (ret) {
+		qxl_release_free(qdev, release);
 		return ret;
-
+	}
 	cmd = (struct qxl_surface_cmd *)qxl_release_map(qdev, release);
 	cmd->type = QXL_SURFACE_CMD_CREATE;
 	cmd->flags = QXL_SURF_FLAG_KEEP_DATA;

[PATCH 4.19 04/37] drm/qxl: qxl_release use after free

[Greg Kroah-Hartman]

From: Vasily Averin <vvs@virtuozzo.com>

commit 933db73351d359f74b14f4af095808260aff11f9 upstream.

qxl_release should not be accesses after qxl_push_*_ring_release() calls:
userspace driver can process submitted command quickly, move qxl_release
into release_ring, generate interrupt and trigger garbage collector.

It can lead to crashes in qxl driver or trigger memory corruption
in some kmalloc-192 slab object

Gerd Hoffmann proposes to swap the qxl_release_fence_buffer_objects() +
qxl_push_{cursor,command}_ring_release() calls to close that race window.

cc: stable@vger.kernel.org
Fixes: f64122c1f6ad ("drm: add new QXL driver. (v1.4)")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Link: http://patchwork.freedesktop.org/patch/msgid/fa17b338-66ae-f299-68fe-8d32419d9071@virtuozzo.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
[backported to v.4.19 stable]
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/qxl/qxl_cmd.c     |    5 ++---
 drivers/gpu/drm/qxl/qxl_display.c |    6 +++---
 drivers/gpu/drm/qxl/qxl_draw.c    |    8 ++++----
 drivers/gpu/drm/qxl/qxl_ioctl.c   |    5 +----
 4 files changed, 10 insertions(+), 14 deletions(-)

--- a/drivers/gpu/drm/qxl/qxl_cmd.c
+++ b/drivers/gpu/drm/qxl/qxl_cmd.c
@@ -501,8 +501,8 @@ int qxl_hw_surface_alloc(struct qxl_devi
 	/* no need to add a release to the fence for this surface bo,
 	   since it is only released when we ask to destroy the surface
 	   and it would never signal otherwise */
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_SURFACE, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_SURFACE, false);
 
 	surf->hw_surf_alloc = true;
 	spin_lock(&qdev->surf_id_idr_lock);
@@ -544,9 +544,8 @@ int qxl_hw_surface_dealloc(struct qxl_de
 	cmd->surface_id = id;
 	qxl_release_unmap(qdev, release, &cmd->release_info);
 
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_SURFACE, false);
-
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_SURFACE, false);
 
 	return 0;
 }
--- a/drivers/gpu/drm/qxl/qxl_display.c
+++ b/drivers/gpu/drm/qxl/qxl_display.c
@@ -532,8 +532,8 @@ static int qxl_primary_apply_cursor(stru
 	cmd->u.set.visible = 1;
 	qxl_release_unmap(qdev, release, &cmd->release_info);
 
-	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 
 	return ret;
 
@@ -694,8 +694,8 @@ static void qxl_cursor_atomic_update(str
 	cmd->u.position.y = plane->state->crtc_y + fb->hot_y;
 
 	qxl_release_unmap(qdev, release, &cmd->release_info);
-	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 
 	if (old_cursor_bo)
 		qxl_bo_unref(&old_cursor_bo);
@@ -740,8 +740,8 @@ static void qxl_cursor_atomic_disable(st
 	cmd->type = QXL_CURSOR_HIDE;
 	qxl_release_unmap(qdev, release, &cmd->release_info);
 
-	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_cursor_ring_release(qdev, release, QXL_CMD_CURSOR, false);
 }
 
 static int qxl_plane_prepare_fb(struct drm_plane *plane,
--- a/drivers/gpu/drm/qxl/qxl_draw.c
+++ b/drivers/gpu/drm/qxl/qxl_draw.c
@@ -241,8 +241,8 @@ void qxl_draw_opaque_fb(const struct qxl
 		qxl_bo_physical_address(qdev, dimage->bo, 0);
 	qxl_release_unmap(qdev, release, &drawable->release_info);
 
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 
 out_free_palette:
 	if (palette_bo)
@@ -382,8 +382,8 @@ void qxl_draw_dirty_fb(struct qxl_device
 	}
 	qxl_bo_kunmap(clips_bo);
 
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 
 out_release_backoff:
 	if (ret)
@@ -433,8 +433,8 @@ void qxl_draw_copyarea(struct qxl_device
 	drawable->u.copy_bits.src_pos.y = sy;
 	qxl_release_unmap(qdev, release, &drawable->release_info);
 
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 
 out_free_release:
 	if (ret)
@@ -477,8 +477,8 @@ void qxl_draw_fill(struct qxl_draw_fill
 
 	qxl_release_unmap(qdev, release, &drawable->release_info);
 
-	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 	qxl_release_fence_buffer_objects(release);
+	qxl_push_command_ring_release(qdev, release, QXL_CMD_DRAW, false);
 
 out_free_release:
 	if (ret)
--- a/drivers/gpu/drm/qxl/qxl_ioctl.c
+++ b/drivers/gpu/drm/qxl/qxl_ioctl.c
@@ -257,11 +257,8 @@ static int qxl_process_single_command(st
 			apply_surf_reloc(qdev, &reloc_info[i]);
 	}
 
+	qxl_release_fence_buffer_objects(release);
 	ret = qxl_push_command_ring_release(qdev, release, cmd->type, true);
-	if (ret)
-		qxl_release_backoff_reserve_list(release);
-	else
-		qxl_release_fence_buffer_objects(release);
 
 out_free_bos:
 out_free_release:

[PATCH 4.19 05/37] btrfs: fix block group leak when removing fails

[Greg Kroah-Hartman]

From: Xiyu Yang <xiyuyang19@fudan.edu.cn>

commit f6033c5e333238f299c3ae03fac8cc1365b23b77 upstream.

btrfs_remove_block_group() invokes btrfs_lookup_block_group(), which
returns a local reference of the block group that contains the given
bytenr to "block_group" with increased refcount.

When btrfs_remove_block_group() returns, "block_group" becomes invalid,
so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in several exception handling paths
of btrfs_remove_block_group(). When those error scenarios occur such as
btrfs_alloc_path() returns NULL, the function forgets to decrease its
refcnt increased by btrfs_lookup_block_group() and will cause a refcnt
leak.

Fix this issue by jumping to "out_put_group" label and calling
btrfs_put_block_group() when those error scenarios occur.

CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/btrfs/extent-tree.c |   16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -10286,7 +10286,7 @@ int btrfs_remove_block_group(struct btrf
 	path = btrfs_alloc_path();
 	if (!path) {
 		ret = -ENOMEM;
-		goto out;
+		goto out_put_group;
 	}
 
 	/*
@@ -10323,7 +10323,7 @@ int btrfs_remove_block_group(struct btrf
 		ret = btrfs_orphan_add(trans, BTRFS_I(inode));
 		if (ret) {
 			btrfs_add_delayed_iput(inode);
-			goto out;
+			goto out_put_group;
 		}
 		clear_nlink(inode);
 		/* One for the block groups ref */
@@ -10346,13 +10346,13 @@ int btrfs_remove_block_group(struct btrf
 
 	ret = btrfs_search_slot(trans, tree_root, &key, path, -1, 1);
 	if (ret < 0)
-		goto out;
+		goto out_put_group;
 	if (ret > 0)
 		btrfs_release_path(path);
 	if (ret == 0) {
 		ret = btrfs_del_item(trans, tree_root, path);
 		if (ret)
-			goto out;
+			goto out_put_group;
 		btrfs_release_path(path);
 	}
 
@@ -10494,9 +10494,9 @@ int btrfs_remove_block_group(struct btrf
 
 	ret = remove_block_group_free_space(trans, block_group);
 	if (ret)
-		goto out;
+		goto out_put_group;
 
-	btrfs_put_block_group(block_group);
+	/* Once for the block groups rbtree */
 	btrfs_put_block_group(block_group);
 
 	ret = btrfs_search_slot(trans, root, &key, path, -1, 1);
@@ -10524,6 +10524,10 @@ int btrfs_remove_block_group(struct btrf
 		/* once for the tree */
 		free_extent_map(em);
 	}
+
+out_put_group:
+	/* Once for the lookup reference */
+	btrfs_put_block_group(block_group);
 out:
 	btrfs_free_path(path);
 	return ret;

[PATCH 4.19 06/37] ALSA: hda/realtek - Two front mics on a Lenovo ThinkCenter

[Greg Kroah-Hartman]

From: Hui Wang <hui.wang@canonical.com>

commit ef0b3203c758b6b8abdb5dca651880347eae6b8c upstream.

This new Lenovo ThinkCenter has two front mics which can't be handled
by PA so far, so apply the fixup ALC283_FIXUP_HEADSET_MIC to change
the location for one of the mics.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200427030039.10121-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_realtek.c |    1 +
 1 file changed, 1 insertion(+)

--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6991,6 +6991,7 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x1558, 0x8560, "System76 Gazelle (gaze14)", ALC269_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x1558, 0x8561, "System76 Gazelle (gaze14)", ALC269_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x1036, "Lenovo P520", ALC233_FIXUP_LENOVO_MULTI_CODECS),
+	SND_PCI_QUIRK(0x17aa, 0x1048, "ThinkCentre Station", ALC283_FIXUP_HEADSET_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x20f2, "Thinkpad SL410/510", ALC269_FIXUP_SKU_IGNORE),
 	SND_PCI_QUIRK(0x17aa, 0x215e, "Thinkpad L512", ALC269_FIXUP_SKU_IGNORE),
 	SND_PCI_QUIRK(0x17aa, 0x21b8, "Thinkpad Edge 14", ALC269_FIXUP_SKU_IGNORE),

[PATCH 4.19 07/37] ALSA: usb-audio: Correct a typo of NuPrime DAC-10 USB ID

[Greg Kroah-Hartman]

From: Takashi Iwai <tiwai@suse.de>

commit 547d2c9cf4f1f72adfecacbd5b093681fb0e8b3e upstream.

The USB vendor ID of NuPrime DAC-10 is not 16b0 but 16d0.

Fixes: f656891c6619 ("ALSA: usb-audio: add more quirks for DSD interfaces")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200430124755.15940-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/usb/quirks.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/sound/usb/quirks.c
+++ b/sound/usb/quirks.c
@@ -1385,7 +1385,7 @@ u64 snd_usb_interface_dsd_format_quirks(
 
 	case USB_ID(0x0d8c, 0x0316): /* Hegel HD12 DSD */
 	case USB_ID(0x10cb, 0x0103): /* The Bit Opus #3; with fp->dsd_raw */
-	case USB_ID(0x16b0, 0x06b2): /* NuPrime DAC-10 */
+	case USB_ID(0x16d0, 0x06b2): /* NuPrime DAC-10 */
 	case USB_ID(0x16d0, 0x09dd): /* Encore mDSD */
 	case USB_ID(0x16d0, 0x0733): /* Furutech ADL Stratos */
 	case USB_ID(0x16d0, 0x09db): /* NuPrime Audio DAC-9 */

[PATCH 4.19 08/37] ALSA: hda/hdmi: fix without unlocked before return

[Greg Kroah-Hartman]

From: Wu Bo <wubo40@huawei.com>

commit a2f647240998aa49632fb09b01388fdf2b87acfc upstream.

Fix the following coccicheck warning:
sound/pci/hda/patch_hdmi.c:1852:2-8: preceding lock on line 1846

After add sanity check to pass klockwork check,
The spdif_mutex should be unlock before return true
in check_non_pcm_per_cvt().

Fixes: 960a581e22d9 ("ALSA: hda: fix some klockwork scan warnings")
Signed-off-by: Wu Bo <wubo40@huawei.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587907042-694161-1-git-send-email-wubo40@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_hdmi.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/sound/pci/hda/patch_hdmi.c
+++ b/sound/pci/hda/patch_hdmi.c
@@ -1848,8 +1848,10 @@ static bool check_non_pcm_per_cvt(struct
 	/* Add sanity check to pass klockwork check.
 	 * This should never happen.
 	 */
-	if (WARN_ON(spdif == NULL))
+	if (WARN_ON(spdif == NULL)) {
+		mutex_unlock(&codec->spdif_mutex);
 		return true;
+	}
 	non_pcm = !!(spdif->status & IEC958_AES0_NONAUDIO);
 	mutex_unlock(&codec->spdif_mutex);
 	return non_pcm;

[PATCH 4.19 09/37] ALSA: pcm: oss: Place the plugin buffer overflow checks correctly

[Greg Kroah-Hartman]

From: Takashi Iwai <tiwai@suse.de>

commit 4285de0725b1bf73608abbcd35ad7fd3ddc0b61e upstream.

The checks of the plugin buffer overflow in the previous fix by commit
  f2ecf903ef06 ("ALSA: pcm: oss: Avoid plugin buffer overflow")
are put in the wrong places mistakenly, which leads to the expected
(repeated) sound when the rate plugin is involved.  Fix in the right
places.

Also, at those right places, the zero check is needed for the
termination node, so added there as well, and let's get it done,
finally.

Fixes: f2ecf903ef06 ("ALSA: pcm: oss: Avoid plugin buffer overflow")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200424193350.19678-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/core/oss/pcm_plugin.c |   20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

--- a/sound/core/oss/pcm_plugin.c
+++ b/sound/core/oss/pcm_plugin.c
@@ -211,21 +211,23 @@ static snd_pcm_sframes_t plug_client_siz
 	if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
 		plugin = snd_pcm_plug_last(plug);
 		while (plugin && drv_frames > 0) {
-			if (check_size && drv_frames > plugin->buf_frames)
-				drv_frames = plugin->buf_frames;
 			plugin_prev = plugin->prev;
 			if (plugin->src_frames)
 				drv_frames = plugin->src_frames(plugin, drv_frames);
+			if (check_size && plugin->buf_frames &&
+			    drv_frames > plugin->buf_frames)
+				drv_frames = plugin->buf_frames;
 			plugin = plugin_prev;
 		}
 	} else if (stream == SNDRV_PCM_STREAM_CAPTURE) {
 		plugin = snd_pcm_plug_first(plug);
 		while (plugin && drv_frames > 0) {
 			plugin_next = plugin->next;
+			if (check_size && plugin->buf_frames &&
+			    drv_frames > plugin->buf_frames)
+				drv_frames = plugin->buf_frames;
 			if (plugin->dst_frames)
 				drv_frames = plugin->dst_frames(plugin, drv_frames);
-			if (check_size && drv_frames > plugin->buf_frames)
-				drv_frames = plugin->buf_frames;
 			plugin = plugin_next;
 		}
 	} else
@@ -251,26 +253,28 @@ static snd_pcm_sframes_t plug_slave_size
 		plugin = snd_pcm_plug_first(plug);
 		while (plugin && frames > 0) {
 			plugin_next = plugin->next;
+			if (check_size && plugin->buf_frames &&
+			    frames > plugin->buf_frames)
+				frames = plugin->buf_frames;
 			if (plugin->dst_frames) {
 				frames = plugin->dst_frames(plugin, frames);
 				if (frames < 0)
 					return frames;
 			}
-			if (check_size && frames > plugin->buf_frames)
-				frames = plugin->buf_frames;
 			plugin = plugin_next;
 		}
 	} else if (stream == SNDRV_PCM_STREAM_CAPTURE) {
 		plugin = snd_pcm_plug_last(plug);
 		while (plugin) {
-			if (check_size && frames > plugin->buf_frames)
-				frames = plugin->buf_frames;
 			plugin_prev = plugin->prev;
 			if (plugin->src_frames) {
 				frames = plugin->src_frames(plugin, frames);
 				if (frames < 0)
 					return frames;
 			}
+			if (check_size && plugin->buf_frames &&
+			    frames > plugin->buf_frames)
+				frames = plugin->buf_frames;
 			plugin = plugin_prev;
 		}
 	} else

[PATCH 4.19 10/37] PM: ACPI: Output correct message on target power state

[Greg Kroah-Hartman]

From: Kai-Heng Feng <kai.heng.feng@canonical.com>

commit a9b760b0266f563b4784f695bbd0e717610dc10a upstream.

Transitioned power state logged at the end of setting ACPI power.

However, D3cold won't be in the message because state can only be
D3hot at most.

Use target_state to corretly report when power state is D3cold.

Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/acpi/device_pm.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/drivers/acpi/device_pm.c
+++ b/drivers/acpi/device_pm.c
@@ -227,13 +227,13 @@ int acpi_device_set_power(struct acpi_de
  end:
 	if (result) {
 		dev_warn(&device->dev, "Failed to change power state to %s\n",
-			 acpi_power_state_string(state));
+			 acpi_power_state_string(target_state));
 	} else {
 		device->power.state = target_state;
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 				  "Device [%s] transitioned to %s\n",
 				  device->pnp.bus_id,
-				  acpi_power_state_string(state)));
+				  acpi_power_state_string(target_state)));
 	}
 
 	return result;

[PATCH 4.19 11/37] PM: hibernate: Freeze kernel threads in software_resume()

[Greg Kroah-Hartman]

From: Dexuan Cui <decui@microsoft.com>

commit 2351f8d295ed63393190e39c2f7c1fee1a80578f upstream.

Currently the kernel threads are not frozen in software_resume(), so
between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
system_freezable_power_efficient_wq can still try to submit SCSI
commands and this can cause a panic since the low level SCSI driver
(e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
any SCSI commands: https://lkml.org/lkml/2020/4/10/47

At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
to resolve the issue from hv_storvsc, but with the help of
Bart Van Assche, I realized it's better to fix software_resume(),
since this looks like a generic issue, not only pertaining to SCSI.

Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 kernel/power/hibernate.c |    7 +++++++
 1 file changed, 7 insertions(+)

--- a/kernel/power/hibernate.c
+++ b/kernel/power/hibernate.c
@@ -901,6 +901,13 @@ static int software_resume(void)
 	error = freeze_processes();
 	if (error)
 		goto Close_Finish;
+
+	error = freeze_kernel_threads();
+	if (error) {
+		thaw_processes();
+		goto Close_Finish;
+	}
+
 	error = load_image_and_restore();
 	thaw_processes();
  Finish:

Re: [PATCH 4.19 11/37] PM: hibernate: Freeze kernel threads in software_resume()

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1884 bytes --]

Hi!

> commit 2351f8d295ed63393190e39c2f7c1fee1a80578f upstream.
> 
> Currently the kernel threads are not frozen in software_resume(), so
> between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
> system_freezable_power_efficient_wq can still try to submit SCSI
> commands and this can cause a panic since the low level SCSI driver
> (e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
> any SCSI commands: https://lkml.org/lkml/2020/4/10/47
> 
> At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
> to resolve the issue from hv_storvsc, but with the help of
> Bart Van Assche, I realized it's better to fix software_resume(),
> since this looks like a generic issue, not only pertaining to SCSI.

I believe it is too soon to merge this into stable. It is rather big
hammer. Yes, it is right thing to do. But I'd wait for 5.7 to be
released before merging it to stable.

It needs some testing and it did not get any.

Best regards,
							Pavel

> Cc: All applicable <stable@vger.kernel.org>
> Signed-off-by: Dexuan Cui <decui@microsoft.com>
> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> 
> ---
>  kernel/power/hibernate.c |    7 +++++++
>  1 file changed, 7 insertions(+)
> 
> --- a/kernel/power/hibernate.c
> +++ b/kernel/power/hibernate.c
> @@ -901,6 +901,13 @@ static int software_resume(void)
>  	error = freeze_processes();
>  	if (error)
>  		goto Close_Finish;
> +
> +	error = freeze_kernel_threads();
> +	if (error) {
> +		thaw_processes();
> +		goto Close_Finish;
> +	}
> +
>  	error = load_image_and_restore();
>  	thaw_processes();
>   Finish:
> 

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

RE: [PATCH 4.19 11/37] PM: hibernate: Freeze kernel threads in software_resume()

[Dexuan Cui]

> From: Pavel Machek <pavel@denx.de>
> Sent: Tuesday, May 5, 2020 5:10 AM
> To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: linux-kernel@vger.kernel.org; stable@vger.kernel.org; Dexuan Cui
> <decui@microsoft.com>; Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> Subject: Re: [PATCH 4.19 11/37] PM: hibernate: Freeze kernel threads in
> software_resume()
> 
> Hi!
> 
> > commit 2351f8d295ed63393190e39c2f7c1fee1a80578f upstream.
> >
> > Currently the kernel threads are not frozen in software_resume(), so
> > between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
> > system_freezable_power_efficient_wq can still try to submit SCSI
> > commands and this can cause a panic since the low level SCSI driver
> > (e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
> > any SCSI commands: https://lkml.org/lkml/2020/4/10/47
> >
> > At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
> > to resolve the issue from hv_storvsc, but with the help of
> > Bart Van Assche, I realized it's better to fix software_resume(),
> > since this looks like a generic issue, not only pertaining to SCSI.
> 
> I believe it is too soon to merge this into stable. It is rather big
> hammer. Yes, it is right thing to do. But I'd wait for 5.7 to be
> released before merging it to stable.
> 
> It needs some testing and it did not get any.
> 
> Best regards,
> 							Pavel

Hi,
I did do some testing in a Linux VM running on Hyper-V:
Without the patch, I can easily hit the panic I described in the first link
above. With the patch, my Linux VM can hibernate >10K times without
seeing the panic and I don't see any issue caused by the patch.

That being said, I don't mind waiting for 5.7 before we merge the patch
to stable. It would be good for the patch to get more testing from others.

Thanks,
-- Dexuan

[PATCH 4.19 12/37] dm verity fec: fix hash block number in verity_fec_decode

[Greg Kroah-Hartman]

From: Sunwook Eom <speed.eom@samsung.com>

commit ad4e80a639fc61d5ecebb03caa5cdbfb91fcebfc upstream.

The error correction data is computed as if data and hash blocks
were concatenated. But hash block number starts from v->hash_start.
So, we have to calculate hash block number based on that.

Fixes: a739ff3f543af ("dm verity: add support for forward error correction")
Cc: stable@vger.kernel.org
Signed-off-by: Sunwook Eom <speed.eom@samsung.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/md/dm-verity-fec.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/md/dm-verity-fec.c
+++ b/drivers/md/dm-verity-fec.c
@@ -436,7 +436,7 @@ int verity_fec_decode(struct dm_verity *
 	fio->level++;
 
 	if (type == DM_VERITY_BLOCK_TYPE_METADATA)
-		block += v->data_blocks;
+		block = block - v->hash_start + v->data_blocks;
 
 	/*
 	 * For RS(M, N), the continuous FEC data is divided into blocks of N

[PATCH 4.19 13/37] dm writecache: fix data corruption when reloading the target

[Greg Kroah-Hartman]

From: Mikulas Patocka <mpatocka@redhat.com>

commit 31b22120194b5c0d460f59e0c98504de1d3f1f14 upstream.

The dm-writecache reads metadata in the target constructor. However, when
we reload the target, there could be another active instance running on
the same device. This is the sequence of operations when doing a reload:

1. construct new target
2. suspend old target
3. resume new target
4. destroy old target

Metadata that were written by the old target between steps 1 and 2 would
not be visible by the new target.

Fix the data corruption by loading the metadata in the resume handler.

Also, validate block_size is at least as large as both the devices'
logical block size and only read 1 block from the metadata during
target constructor -- no need to read entirety of metadata now that it
is done during resume.

Fixes: 48debafe4f2f ("dm: add writecache target")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/md/dm-writecache.c |   52 ++++++++++++++++++++++++++++++++-------------
 1 file changed, 37 insertions(+), 15 deletions(-)

--- a/drivers/md/dm-writecache.c
+++ b/drivers/md/dm-writecache.c
@@ -884,6 +884,24 @@ static int writecache_alloc_entries(stru
 	return 0;
 }
 
+static int writecache_read_metadata(struct dm_writecache *wc, sector_t n_sectors)
+{
+	struct dm_io_region region;
+	struct dm_io_request req;
+
+	region.bdev = wc->ssd_dev->bdev;
+	region.sector = wc->start_sector;
+	region.count = n_sectors;
+	req.bi_op = REQ_OP_READ;
+	req.bi_op_flags = REQ_SYNC;
+	req.mem.type = DM_IO_VMA;
+	req.mem.ptr.vma = (char *)wc->memory_map;
+	req.client = wc->dm_io;
+	req.notify.fn = NULL;
+
+	return dm_io(&req, 1, &region, NULL);
+}
+
 static void writecache_resume(struct dm_target *ti)
 {
 	struct dm_writecache *wc = ti->private;
@@ -894,8 +912,18 @@ static void writecache_resume(struct dm_
 
 	wc_lock(wc);
 
-	if (WC_MODE_PMEM(wc))
+	if (WC_MODE_PMEM(wc)) {
 		persistent_memory_invalidate_cache(wc->memory_map, wc->memory_map_size);
+	} else {
+		r = writecache_read_metadata(wc, wc->metadata_sectors);
+		if (r) {
+			size_t sb_entries_offset;
+			writecache_error(wc, r, "unable to read metadata: %d", r);
+			sb_entries_offset = offsetof(struct wc_memory_superblock, entries);
+			memset((char *)wc->memory_map + sb_entries_offset, -1,
+			       (wc->metadata_sectors << SECTOR_SHIFT) - sb_entries_offset);
+		}
+	}
 
 	wc->tree = RB_ROOT;
 	INIT_LIST_HEAD(&wc->lru);
@@ -1978,6 +2006,12 @@ static int writecache_ctr(struct dm_targ
 		ti->error = "Invalid block size";
 		goto bad;
 	}
+	if (wc->block_size < bdev_logical_block_size(wc->dev->bdev) ||
+	    wc->block_size < bdev_logical_block_size(wc->ssd_dev->bdev)) {
+		r = -EINVAL;
+		ti->error = "Block size is smaller than device logical block size";
+		goto bad;
+	}
 	wc->block_size_bits = __ffs(wc->block_size);
 
 	wc->max_writeback_jobs = MAX_WRITEBACK_JOBS;
@@ -2066,8 +2100,6 @@ invalid_optional:
 			goto bad;
 		}
 	} else {
-		struct dm_io_region region;
-		struct dm_io_request req;
 		size_t n_blocks, n_metadata_blocks;
 		uint64_t n_bitmap_bits;
 
@@ -2124,19 +2156,9 @@ invalid_optional:
 			goto bad;
 		}
 
-		region.bdev = wc->ssd_dev->bdev;
-		region.sector = wc->start_sector;
-		region.count = wc->metadata_sectors;
-		req.bi_op = REQ_OP_READ;
-		req.bi_op_flags = REQ_SYNC;
-		req.mem.type = DM_IO_VMA;
-		req.mem.ptr.vma = (char *)wc->memory_map;
-		req.client = wc->dm_io;
-		req.notify.fn = NULL;
-
-		r = dm_io(&req, 1, &region, NULL);
+		r = writecache_read_metadata(wc, wc->block_size >> SECTOR_SHIFT);
 		if (r) {
-			ti->error = "Unable to read metadata";
+			ti->error = "Unable to read first block of metadata";
 			goto bad;
 		}
 	}

[PATCH 4.19 14/37] dm multipath: use updated MPATHF_QUEUE_IO on mapping for bio-based mpath

[Greg Kroah-Hartman]

From: Gabriel Krisman Bertazi <krisman@collabora.com>

commit 5686dee34dbfe0238c0274e0454fa0174ac0a57a upstream.

When adding devices that don't have a scsi_dh on a BIO based multipath,
I was able to consistently hit the warning below and lock-up the system.

The problem is that __map_bio reads the flag before it potentially being
modified by choose_pgpath, and ends up using the older value.

The WARN_ON below is not trivially linked to the issue. It goes like
this: The activate_path delayed_work is not initialized for non-scsi_dh
devices, but we always set MPATHF_QUEUE_IO, asking for initialization.
That is fine, since MPATHF_QUEUE_IO would be cleared in choose_pgpath.
Nevertheless, only for BIO-based mpath, we cache the flag before calling
choose_pgpath, and use the older version when deciding if we should
initialize the path.  Therefore, we end up trying to initialize the
paths, and calling the non-initialized activate_path work.

[   82.437100] ------------[ cut here ]------------
[   82.437659] WARNING: CPU: 3 PID: 602 at kernel/workqueue.c:1624
  __queue_delayed_work+0x71/0x90
[   82.438436] Modules linked in:
[   82.438911] CPU: 3 PID: 602 Comm: systemd-udevd Not tainted 5.6.0-rc6+ #339
[   82.439680] RIP: 0010:__queue_delayed_work+0x71/0x90
[   82.440287] Code: c1 48 89 4a 50 81 ff 00 02 00 00 75 2a 4c 89 cf e9
94 d6 07 00 e9 7f e9 ff ff 0f 0b eb c7 0f 0b 48 81 7a 58 40 74 a8 94 74
a7 <0f> 0b 48 83 7a 48 00 74 a5 0f 0b eb a1 89 fe 4c 89 cf e9 c8 c4 07
[   82.441719] RSP: 0018:ffffb738803977c0 EFLAGS: 00010007
[   82.442121] RAX: ffffa086389f9740 RBX: 0000000000000002 RCX: 0000000000000000
[   82.442718] RDX: ffffa086350dd930 RSI: ffffa0863d76f600 RDI: 0000000000000200
[   82.443484] RBP: 0000000000000200 R08: 0000000000000000 R09: ffffa086350dd970
[   82.444128] R10: 0000000000000000 R11: 0000000000000000 R12: ffffa086350dd930
[   82.444773] R13: ffffa0863d76f600 R14: 0000000000000000 R15: ffffa08636738008
[   82.445427] FS:  00007f6abfe9dd40(0000) GS:ffffa0863dd80000(0000) knlGS:00000
[   82.446040] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   82.446478] CR2: 0000557d288db4e8 CR3: 0000000078b36000 CR4: 00000000000006e0
[   82.447104] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   82.447561] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   82.448012] Call Trace:
[   82.448164]  queue_delayed_work_on+0x6d/0x80
[   82.448472]  __pg_init_all_paths+0x7b/0xf0
[   82.448714]  pg_init_all_paths+0x26/0x40
[   82.448980]  __multipath_map_bio.isra.0+0x84/0x210
[   82.449267]  __map_bio+0x3c/0x1f0
[   82.449468]  __split_and_process_non_flush+0x14a/0x1b0
[   82.449775]  __split_and_process_bio+0xde/0x340
[   82.450045]  ? dm_get_live_table+0x5/0xb0
[   82.450278]  dm_process_bio+0x98/0x290
[   82.450518]  dm_make_request+0x54/0x120
[   82.450778]  generic_make_request+0xd2/0x3e0
[   82.451038]  ? submit_bio+0x3c/0x150
[   82.451278]  submit_bio+0x3c/0x150
[   82.451492]  mpage_readpages+0x129/0x160
[   82.451756]  ? bdev_evict_inode+0x1d0/0x1d0
[   82.452033]  read_pages+0x72/0x170
[   82.452260]  __do_page_cache_readahead+0x1ba/0x1d0
[   82.452624]  force_page_cache_readahead+0x96/0x110
[   82.452903]  generic_file_read_iter+0x84f/0xae0
[   82.453192]  ? __seccomp_filter+0x7c/0x670
[   82.453547]  new_sync_read+0x10e/0x190
[   82.453883]  vfs_read+0x9d/0x150
[   82.454172]  ksys_read+0x65/0xe0
[   82.454466]  do_syscall_64+0x4e/0x210
[   82.454828]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[...]
[   82.462501] ---[ end trace bb39975e9cf45daa ]---

Cc: stable@vger.kernel.org
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/md/dm-mpath.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

--- a/drivers/md/dm-mpath.c
+++ b/drivers/md/dm-mpath.c
@@ -586,10 +586,12 @@ static struct pgpath *__map_bio(struct m
 
 	/* Do we need to select a new pgpath? */
 	pgpath = READ_ONCE(m->current_pgpath);
-	queue_io = test_bit(MPATHF_QUEUE_IO, &m->flags);
-	if (!pgpath || !queue_io)
+	if (!pgpath || !test_bit(MPATHF_QUEUE_IO, &m->flags))
 		pgpath = choose_pgpath(m, bio->bi_iter.bi_size);
 
+	/* MPATHF_QUEUE_IO might have been cleared by choose_pgpath. */
+	queue_io = test_bit(MPATHF_QUEUE_IO, &m->flags);
+
 	if ((pgpath && queue_io) ||
 	    (!pgpath && test_bit(MPATHF_QUEUE_IF_NO_PATH, &m->flags))) {
 		/* Queue for the daemon to resubmit */

[PATCH 4.19 15/37] scsi: qla2xxx: set UNLOADING before waiting for session deletion

[Greg Kroah-Hartman]

From: Martin Wilck <mwilck@suse.com>

commit 856e152a3c08bf7987cbd41900741d83d9cddc8e upstream.

The purpose of the UNLOADING flag is to avoid port login procedures to
continue when a controller is in the process of shutting down.  It makes
sense to set this flag before starting session teardown.

Furthermore, use atomic test_and_set_bit() to avoid the shutdown being run
multiple times in parallel. In qla2x00_disable_board_on_pci_error(), the
test for UNLOADING is postponed until after the check for an already
disabled PCI board.

Link: https://lore.kernel.org/r/20200421204621.19228-2-mwilck@suse.com
Fixes: 45235022da99 ("scsi: qla2xxx: Fix driver unload by shutting down chip")
Reviewed-by: Arun Easi <aeasi@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/scsi/qla2xxx/qla_os.c |   32 ++++++++++++++------------------
 1 file changed, 14 insertions(+), 18 deletions(-)

--- a/drivers/scsi/qla2xxx/qla_os.c
+++ b/drivers/scsi/qla2xxx/qla_os.c
@@ -3654,6 +3654,13 @@ qla2x00_remove_one(struct pci_dev *pdev)
 	}
 	qla2x00_wait_for_hba_ready(base_vha);
 
+	/*
+	 * if UNLOADING flag is already set, then continue unload,
+	 * where it was set first.
+	 */
+	if (test_and_set_bit(UNLOADING, &base_vha->dpc_flags))
+		return;
+
 	if (IS_QLA25XX(ha) || IS_QLA2031(ha) || IS_QLA27XX(ha)) {
 		if (ha->flags.fw_started)
 			qla2x00_abort_isp_cleanup(base_vha);
@@ -3671,15 +3678,6 @@ qla2x00_remove_one(struct pci_dev *pdev)
 
 	qla2x00_wait_for_sess_deletion(base_vha);
 
-	/*
-	 * if UNLOAD flag is already set, then continue unload,
-	 * where it was set first.
-	 */
-	if (test_bit(UNLOADING, &base_vha->dpc_flags))
-		return;
-
-	set_bit(UNLOADING, &base_vha->dpc_flags);
-
 	qla_nvme_delete(base_vha);
 
 	dma_free_coherent(&ha->pdev->dev,
@@ -5845,13 +5843,6 @@ qla2x00_disable_board_on_pci_error(struc
 	struct pci_dev *pdev = ha->pdev;
 	scsi_qla_host_t *base_vha = pci_get_drvdata(ha->pdev);
 
-	/*
-	 * if UNLOAD flag is already set, then continue unload,
-	 * where it was set first.
-	 */
-	if (test_bit(UNLOADING, &base_vha->dpc_flags))
-		return;
-
 	ql_log(ql_log_warn, base_vha, 0x015b,
 	    "Disabling adapter.\n");
 
@@ -5862,9 +5853,14 @@ qla2x00_disable_board_on_pci_error(struc
 		return;
 	}
 
-	qla2x00_wait_for_sess_deletion(base_vha);
+	/*
+	 * if UNLOADING flag is already set, then continue unload,
+	 * where it was set first.
+	 */
+	if (test_and_set_bit(UNLOADING, &base_vha->dpc_flags))
+		return;
 
-	set_bit(UNLOADING, &base_vha->dpc_flags);
+	qla2x00_wait_for_sess_deletion(base_vha);
 
 	qla2x00_delete_all_vps(ha, base_vha);
 

[PATCH 4.19 16/37] scsi: qla2xxx: check UNLOADING before posting async work

[Greg Kroah-Hartman]

From: Martin Wilck <mwilck@suse.com>

commit 5a263892d7d0b4fe351363f8d1a14c6a75955475 upstream.

qlt_free_session_done() tries to post async PRLO / LOGO, and waits for the
completion of these async commands. If UNLOADING is set, this is doomed to
timeout, because the async logout command will never complete.

The only way to avoid waiting pointlessly is to fail posting these commands
in the first place if the driver is in UNLOADING state.  In general,
posting any command should be avoided when the driver is UNLOADING.

With this patch, "rmmod qla2xxx" completes without noticeable delay.

Link: https://lore.kernel.org/r/20200421204621.19228-3-mwilck@suse.com
Fixes: 45235022da99 ("scsi: qla2xxx: Fix driver unload by shutting down chip")
Acked-by: Arun Easi <aeasi@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/scsi/qla2xxx/qla_os.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/scsi/qla2xxx/qla_os.c
+++ b/drivers/scsi/qla2xxx/qla_os.c
@@ -4645,6 +4645,9 @@ qla2x00_alloc_work(struct scsi_qla_host
 	struct qla_work_evt *e;
 	uint8_t bail;
 
+	if (test_bit(UNLOADING, &vha->dpc_flags))
+		return NULL;
+
 	QLA_VHA_MARK_BUSY(vha, bail);
 	if (bail)
 		return NULL;

[PATCH 4.19 17/37] RDMA/mlx5: Set GRH fields in query QP on RoCE

[Greg Kroah-Hartman]

From: Aharon Landau <aharonl@mellanox.com>

commit 2d7e3ff7b6f2c614eb21d0dc348957a47eaffb57 upstream.

GRH fields such as sgid_index, hop limit, et. are set in the QP context
when QP is created/modified.

Currently, when query QP is performed, we fill the GRH fields only if the
GRH bit is set in the QP context, but this bit is not set for RoCE. Adjust
the check so we will set all relevant data for the RoCE too.

Since this data is returned to userspace, the below is an ABI regression.

Fixes: d8966fcd4c25 ("IB/core: Use rdma_ah_attr accessor functions")
Link: https://lore.kernel.org/r/20200413132028.930109-1-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/infiniband/hw/mlx5/qp.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/drivers/infiniband/hw/mlx5/qp.c
+++ b/drivers/infiniband/hw/mlx5/qp.c
@@ -4887,7 +4887,9 @@ static void to_rdma_ah_attr(struct mlx5_
 	rdma_ah_set_path_bits(ah_attr, path->grh_mlid & 0x7f);
 	rdma_ah_set_static_rate(ah_attr,
 				path->static_rate ? path->static_rate - 5 : 0);
-	if (path->grh_mlid & (1 << 7)) {
+
+	if (path->grh_mlid & (1 << 7) ||
+	    ah_attr->type == RDMA_AH_ATTR_TYPE_ROCE) {
 		u32 tc_fl = be32_to_cpu(path->tclass_flowlabel);
 
 		rdma_ah_set_grh(ah_attr, NULL,

[PATCH 4.19 18/37] RDMA/mlx4: Initialize ib_spec on the stack

[Greg Kroah-Hartman]

From: Alaa Hleihel <alaa@mellanox.com>

commit c08cfb2d8d78bfe81b37cc6ba84f0875bddd0d5c upstream.

Initialize ib_spec on the stack before using it, otherwise we will have
garbage values that will break creating default rules with invalid parsing
error.

Fixes: a37a1a428431 ("IB/mlx4: Add mechanism to support flow steering over IB links")
Link: https://lore.kernel.org/r/20200413132235.930642-1-leon@kernel.org
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/infiniband/hw/mlx4/main.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/infiniband/hw/mlx4/main.c
+++ b/drivers/infiniband/hw/mlx4/main.c
@@ -1606,8 +1606,9 @@ static int __mlx4_ib_create_default_rule
 	int i;
 
 	for (i = 0; i < ARRAY_SIZE(pdefault_rules->rules_create_list); i++) {
+		union ib_flow_spec ib_spec = {};
 		int ret;
-		union ib_flow_spec ib_spec;
+
 		switch (pdefault_rules->rules_create_list[i]) {
 		case 0:
 			/* no rule */

[PATCH 4.19 19/37] RDMA/core: Prevent mixed use of FDs between shared ufiles

[Greg Kroah-Hartman]

From: Leon Romanovsky <leonro@mellanox.com>

commit 0fb00941dc63990a10951146df216fc7b0e20bc2 upstream.

FDs can only be used on the ufile that created them, they cannot be mixed
to other ufiles. We are lacking a check to prevent it.

  BUG: KASAN: null-ptr-deref in atomic64_sub_and_test include/asm-generic/atomic-instrumented.h:1547 [inline]
  BUG: KASAN: null-ptr-deref in atomic_long_sub_and_test include/asm-generic/atomic-long.h:460 [inline]
  BUG: KASAN: null-ptr-deref in fput_many+0x1a/0x140 fs/file_table.c:336
  Write of size 8 at addr 0000000000000038 by task syz-executor179/284

  CPU: 0 PID: 284 Comm: syz-executor179 Not tainted 5.5.0-rc5+ #1
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
  Call Trace:
   __dump_stack lib/dump_stack.c:77 [inline]
   dump_stack+0x94/0xce lib/dump_stack.c:118
   __kasan_report+0x18f/0x1b7 mm/kasan/report.c:510
   kasan_report+0xe/0x20 mm/kasan/common.c:639
   check_memory_region_inline mm/kasan/generic.c:185 [inline]
   check_memory_region+0x15d/0x1b0 mm/kasan/generic.c:192
   atomic64_sub_and_test include/asm-generic/atomic-instrumented.h:1547 [inline]
   atomic_long_sub_and_test include/asm-generic/atomic-long.h:460 [inline]
   fput_many+0x1a/0x140 fs/file_table.c:336
   rdma_lookup_put_uobject+0x85/0x130 drivers/infiniband/core/rdma_core.c:692
   uobj_put_read include/rdma/uverbs_std_types.h:96 [inline]
   _ib_uverbs_lookup_comp_file drivers/infiniband/core/uverbs_cmd.c:198 [inline]
   create_cq+0x375/0xba0 drivers/infiniband/core/uverbs_cmd.c:1006
   ib_uverbs_create_cq+0x114/0x140 drivers/infiniband/core/uverbs_cmd.c:1089
   ib_uverbs_write+0xaa5/0xdf0 drivers/infiniband/core/uverbs_main.c:769
   __vfs_write+0x7c/0x100 fs/read_write.c:494
   vfs_write+0x168/0x4a0 fs/read_write.c:558
   ksys_write+0xc8/0x200 fs/read_write.c:611
   do_syscall_64+0x9c/0x390 arch/x86/entry/common.c:294
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x44ef99
  Code: 00 b8 00 01 00 00 eb e1 e8 74 1c 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c4 ff ff ff f7 d8 64 89 01 48
  RSP: 002b:00007ffc0b74c028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 00007ffc0b74c030 RCX: 000000000044ef99
  RDX: 0000000000000040 RSI: 0000000020000040 RDI: 0000000000000005
  RBP: 00007ffc0b74c038 R08: 0000000000401830 R09: 0000000000401830
  R10: 00007ffc0b74c038 R11: 0000000000000246 R12: 0000000000000000
  R13: 0000000000000000 R14: 00000000006be018 R15: 0000000000000000

Fixes: cf8966b3477d ("IB/core: Add support for fd objects")
Link: https://lore.kernel.org/r/20200421082929.311931-2-leon@kernel.org
Suggested-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/infiniband/core/rdma_core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/infiniband/core/rdma_core.c
+++ b/drivers/infiniband/core/rdma_core.c
@@ -381,7 +381,7 @@ lookup_get_fd_uobject(const struct uverb
 	 * and the caller is expected to ensure that uverbs_close_fd is never
 	 * done while a call top lookup is possible.
 	 */
-	if (f->f_op != fd_type->fops) {
+	if (f->f_op != fd_type->fops || uobject->ufile != ufile) {
 		fput(f);
 		return ERR_PTR(-EBADF);
 	}

[PATCH 4.19 20/37] RDMA/core: Fix race between destroy and release FD object

[Greg Kroah-Hartman]

From: Leon Romanovsky <leonro@mellanox.com>

commit f0abc761bbb9418876cc4d1ebc473e4ea6352e42 upstream.

The call to ->lookup_put() was too early and it caused an unlock of the
read/write protection of the uobject after the FD was put. This allows a
race:

     CPU1                                 CPU2
 rdma_lookup_put_uobject()
   lookup_put_fd_uobject()
     fput()
				   fput()
				     uverbs_uobject_fd_release()
				       WARN_ON(uverbs_try_lock_object(uobj,
					       UVERBS_LOOKUP_WRITE));
   atomic_dec(usecnt)

Fix the code by changing the order, first unlock and call to
->lookup_put() after that.

Fixes: 3832125624b7 ("IB/core: Add support for idr types")
Link: https://lore.kernel.org/r/20200423060122.6182-1-leon@kernel.org
Suggested-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/infiniband/core/rdma_core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/infiniband/core/rdma_core.c
+++ b/drivers/infiniband/core/rdma_core.c
@@ -697,7 +697,6 @@ void rdma_lookup_put_uobject(struct ib_u
 			     enum rdma_lookup_mode mode)
 {
 	assert_uverbs_usecnt(uobj, mode);
-	uobj->uapi_object->type_class->lookup_put(uobj, mode);
 	/*
 	 * In order to unlock an object, either decrease its usecnt for
 	 * read access or zero it in case of exclusive access. See
@@ -714,6 +713,7 @@ void rdma_lookup_put_uobject(struct ib_u
 		break;
 	}
 
+	uobj->uapi_object->type_class->lookup_put(uobj, mode);
 	/* Pairs with the kref obtained by type->lookup_get */
 	uverbs_uobject_put(uobj);
 }

[PATCH 4.19 21/37] vfio: avoid possible overflow in vfio_iommu_type1_pin_pages

[Greg Kroah-Hartman]

From: Yan Zhao <yan.y.zhao@intel.com>

commit 0ea971f8dcd6dee78a9a30ea70227cf305f11ff7 upstream.

add parentheses to avoid possible vaddr overflow.

Fixes: a54eb55045ae ("vfio iommu type1: Add support for mediated devices")
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/vfio/vfio_iommu_type1.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/vfio/vfio_iommu_type1.c
+++ b/drivers/vfio/vfio_iommu_type1.c
@@ -598,7 +598,7 @@ static int vfio_iommu_type1_pin_pages(vo
 			continue;
 		}
 
-		remote_vaddr = dma->vaddr + iova - dma->iova;
+		remote_vaddr = dma->vaddr + (iova - dma->iova);
 		ret = vfio_pin_page_external(dma, remote_vaddr, &phys_pfn[i],
 					     do_accounting);
 		if (ret)

Re: [PATCH 4.19 21/37] vfio: avoid possible overflow in vfio_iommu_type1_pin_pages

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1344 bytes --]

On Mon 2020-05-04 19:57:34, Greg Kroah-Hartman wrote:
> From: Yan Zhao <yan.y.zhao@intel.com>
> 
> commit 0ea971f8dcd6dee78a9a30ea70227cf305f11ff7 upstream.
> 
> add parentheses to avoid possible vaddr overflow.

AFAICT the values are unsigned, so yes, this is nice cleanup, but it
does not really fix any problem, right? IOW it overflows, then
underflows, but the result is still correct...

Best regards,
								Pavel

> Fixes: a54eb55045ae ("vfio iommu type1: Add support for mediated devices")
> Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> 
> ---
>  drivers/vfio/vfio_iommu_type1.c |    2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> --- a/drivers/vfio/vfio_iommu_type1.c
> +++ b/drivers/vfio/vfio_iommu_type1.c
> @@ -598,7 +598,7 @@ static int vfio_iommu_type1_pin_pages(vo
>  			continue;
>  		}
>  
> -		remote_vaddr = dma->vaddr + iova - dma->iova;
> +		remote_vaddr = dma->vaddr + (iova - dma->iova);
>  		ret = vfio_pin_page_external(dma, remote_vaddr, &phys_pfn[i],
>  					     do_accounting);
>  		if (ret)
> 

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[PATCH 4.19 22/37] vfio/type1: Fix VA->PA translation for PFNMAP VMAs in vaddr_get_pfn()

[Greg Kroah-Hartman]

From: Sean Christopherson <sean.j.christopherson@intel.com>

commit 5cbf3264bc715e9eb384e2b68601f8c02bb9a61d upstream.

Use follow_pfn() to get the PFN of a PFNMAP VMA instead of assuming that
vma->vm_pgoff holds the base PFN of the VMA.  This fixes a bug where
attempting to do VFIO_IOMMU_MAP_DMA on an arbitrary PFNMAP'd region of
memory calculates garbage for the PFN.

Hilariously, this only got detected because the first "PFN" calculated
by vaddr_get_pfn() is PFN 0 (vma->vm_pgoff==0), and iommu_iova_to_phys()
uses PA==0 as an error, which triggers a WARN in vfio_unmap_unpin()
because the translation "failed".  PFN 0 is now unconditionally reserved
on x86 in order to mitigate L1TF, which causes is_invalid_reserved_pfn()
to return true and in turns results in vaddr_get_pfn() returning success
for PFN 0.  Eventually the bogus calculation runs into PFNs that aren't
reserved and leads to failure in vfio_pin_map_dma().  The subsequent
call to vfio_remove_dma() attempts to unmap PFN 0 and WARNs.

  WARNING: CPU: 8 PID: 5130 at drivers/vfio/vfio_iommu_type1.c:750 vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1]
  Modules linked in: vfio_pci vfio_virqfd vfio_iommu_type1 vfio ...
  CPU: 8 PID: 5130 Comm: sgx Tainted: G        W         5.6.0-rc5-705d787c7fee-vfio+ #3
  Hardware name: Intel Corporation Mehlow UP Server Platform/Moss Beach Server, BIOS CNLSE2R1.D00.X119.B49.1803010910 03/01/2018
  RIP: 0010:vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1]
  Code: <0f> 0b 49 81 c5 00 10 00 00 e9 c5 fe ff ff bb 00 10 00 00 e9 3d fe
  RSP: 0018:ffffbeb5039ebda8 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: ffff9a55cbf8d480 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff9a52b771c200
  RBP: 0000000000000000 R08: 0000000000000040 R09: 00000000fffffff2
  R10: 0000000000000001 R11: ffff9a51fa896000 R12: 0000000184010000
  R13: 0000000184000000 R14: 0000000000010000 R15: ffff9a55cb66ea08
  FS:  00007f15d3830b40(0000) GS:ffff9a55d5600000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000561cf39429e0 CR3: 000000084f75f005 CR4: 00000000003626e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   vfio_remove_dma+0x17/0x70 [vfio_iommu_type1]
   vfio_iommu_type1_ioctl+0x9e3/0xa7b [vfio_iommu_type1]
   ksys_ioctl+0x92/0xb0
   __x64_sys_ioctl+0x16/0x20
   do_syscall_64+0x4c/0x180
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x7f15d04c75d7
  Code: <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 f7 d8 64 89 01 48

Fixes: 73fa0d10d077 ("vfio: Type1 IOMMU implementation")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/vfio/vfio_iommu_type1.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/drivers/vfio/vfio_iommu_type1.c
+++ b/drivers/vfio/vfio_iommu_type1.c
@@ -385,8 +385,8 @@ static int vaddr_get_pfn(struct mm_struc
 	vma = find_vma_intersection(mm, vaddr, vaddr + 1);
 
 	if (vma && vma->vm_flags & VM_PFNMAP) {
-		*pfn = ((vaddr - vma->vm_start) >> PAGE_SHIFT) + vma->vm_pgoff;
-		if (is_invalid_reserved_pfn(*pfn))
+		if (!follow_pfn(vma, vaddr, pfn) &&
+		    is_invalid_reserved_pfn(*pfn))
 			ret = 0;
 	}
 

[PATCH 4.19 23/37] iommu/qcom: Fix local_base status check

[Greg Kroah-Hartman]

From: Tang Bin <tangbin@cmss.chinamobile.com>

commit b52649aee6243ea661905bdc5fbe28cc5f6dec76 upstream.

The function qcom_iommu_device_probe() does not perform sufficient
error checking after executing devm_ioremap_resource(), which can
result in crashes if a critical error path is encountered.

Fixes: 0ae349a0f33f ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200418134703.1760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/iommu/qcom_iommu.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

--- a/drivers/iommu/qcom_iommu.c
+++ b/drivers/iommu/qcom_iommu.c
@@ -797,8 +797,11 @@ static int qcom_iommu_device_probe(struc
 	qcom_iommu->dev = dev;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (res)
+	if (res) {
 		qcom_iommu->local_base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(qcom_iommu->local_base))
+			return PTR_ERR(qcom_iommu->local_base);
+	}
 
 	qcom_iommu->iface_clk = devm_clk_get(dev, "iface");
 	if (IS_ERR(qcom_iommu->iface_clk)) {

[PATCH 4.19 24/37] scsi: target/iblock: fix WRITE SAME zeroing

[Greg Kroah-Hartman]

From: David Disseldorp <ddiss@suse.de>

commit 1d2ff149b263c9325875726a7804a0c75ef7112e upstream.

SBC4 specifies that WRITE SAME requests with the UNMAP bit set to zero
"shall perform the specified write operation to each LBA specified by the
command".  Commit 2237498f0b5c ("target/iblock: Convert WRITE_SAME to
blkdev_issue_zeroout") modified the iblock backend to call
blkdev_issue_zeroout() when handling WRITE SAME requests with UNMAP=0 and a
zero data segment.

The iblock blkdev_issue_zeroout() call incorrectly provides a flags
parameter of 0 (bool false), instead of BLKDEV_ZERO_NOUNMAP.  The bool
false parameter reflects the blkdev_issue_zeroout() API prior to commit
ee472d835c26 ("block: add a flags argument to (__)blkdev_issue_zeroout")
which was merged shortly before 2237498f0b5c.

Link: https://lore.kernel.org/r/20200419163109.11689-1-ddiss@suse.de
Fixes: 2237498f0b5c ("target/iblock: Convert WRITE_SAME to blkdev_issue_zeroout")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/target/target_core_iblock.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/target/target_core_iblock.c
+++ b/drivers/target/target_core_iblock.c
@@ -445,7 +445,7 @@ iblock_execute_zero_out(struct block_dev
 				target_to_linux_sector(dev, cmd->t_task_lba),
 				target_to_linux_sector(dev,
 					sbc_get_write_same_sectors(cmd)),
-				GFP_KERNEL, false);
+				GFP_KERNEL, BLKDEV_ZERO_NOUNMAP);
 	if (ret)
 		return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE;
 

[PATCH 4.19 25/37] iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system

[Greg Kroah-Hartman]

From: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>

commit b74aa02d7a30ee5e262072a7d6e8deff10b37924 upstream.

Currently, system fails to boot because the legacy interrupt remapping
mode does not enable 128-bit IRTE (GA), which is required for x2APIC
support.

Fix by using AMD_IOMMU_GUEST_IR_LEGACY_GA mode when booting with
kernel option amd_iommu_intr=legacy instead. The initialization
logic will check GASup and automatically fallback to using
AMD_IOMMU_GUEST_IR_LEGACY if GA mode is not supported.

Fixes: 3928aa3f5775 ("iommu/amd: Detect and enable guest vAPIC support")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/1587562202-14183-1-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/iommu/amd_iommu_init.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/iommu/amd_iommu_init.c
+++ b/drivers/iommu/amd_iommu_init.c
@@ -2836,7 +2836,7 @@ static int __init parse_amd_iommu_intr(c
 {
 	for (; *str; ++str) {
 		if (strncmp(str, "legacy", 6) == 0) {
-			amd_iommu_guest_ir = AMD_IOMMU_GUEST_IR_LEGACY;
+			amd_iommu_guest_ir = AMD_IOMMU_GUEST_IR_LEGACY_GA;
 			break;
 		}
 		if (strncmp(str, "vapic", 5) == 0) {

[PATCH 4.19 26/37] ALSA: opti9xx: shut up gcc-10 range warning

[Greg Kroah-Hartman]

From: Arnd Bergmann <arnd@arndb.de>

commit 5ce00760a84848d008554c693ceb6286f4d9c509 upstream.

gcc-10 points out a few instances of suspicious integer arithmetic
leading to value truncation:

sound/isa/opti9xx/opti92x-ad1848.c: In function 'snd_opti9xx_configure':
sound/isa/opti9xx/opti92x-ad1848.c:322:43: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_opti9xx_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
  322 |   (snd_opti9xx_read(chip, reg) & ~(mask)) | ((value) & (mask)))
      |   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/opti92x-ad1848.c:351:3: note: in expansion of macro 'snd_opti9xx_write_mask'
  351 |   snd_opti9xx_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
      |   ^~~~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c: In function 'snd_miro_configure':
sound/isa/opti9xx/miro.c:873:40: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_miro_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow]
  873 |   (snd_miro_read(chip, reg) & ~(mask)) | ((value) & (mask)))
      |   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
sound/isa/opti9xx/miro.c:1010:3: note: in expansion of macro 'snd_miro_write_mask'
 1010 |   snd_miro_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff);
      |   ^~~~~~~~~~~~~~~~~~~

These are all harmless here as only the low 8 bit are passed down
anyway. Change the macros to inline functions to make the code
more readable and also avoid the warning.

Strictly speaking those functions also need locking to make the
read/write pair atomic, but it seems unlikely that anyone would
still run into that issue.

Fixes: 1841f613fd2e ("[ALSA] Add snd-miro driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200429190216.85919-1-arnd@arndb.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/isa/opti9xx/miro.c           |    9 ++++++---
 sound/isa/opti9xx/opti92x-ad1848.c |    9 ++++++---
 2 files changed, 12 insertions(+), 6 deletions(-)

--- a/sound/isa/opti9xx/miro.c
+++ b/sound/isa/opti9xx/miro.c
@@ -880,10 +880,13 @@ static void snd_miro_write(struct snd_mi
 	spin_unlock_irqrestore(&chip->lock, flags);
 }
 
+static inline void snd_miro_write_mask(struct snd_miro *chip,
+		unsigned char reg, unsigned char value, unsigned char mask)
+{
+	unsigned char oldval = snd_miro_read(chip, reg);
 
-#define snd_miro_write_mask(chip, reg, value, mask)	\
-	snd_miro_write(chip, reg,			\
-		(snd_miro_read(chip, reg) & ~(mask)) | ((value) & (mask)))
+	snd_miro_write(chip, reg, (oldval & ~mask) | (value & mask));
+}
 
 /*
  *  Proc Interface
--- a/sound/isa/opti9xx/opti92x-ad1848.c
+++ b/sound/isa/opti9xx/opti92x-ad1848.c
@@ -329,10 +329,13 @@ static void snd_opti9xx_write(struct snd
 }
 
 
-#define snd_opti9xx_write_mask(chip, reg, value, mask)	\
-	snd_opti9xx_write(chip, reg,			\
-		(snd_opti9xx_read(chip, reg) & ~(mask)) | ((value) & (mask)))
+static inline void snd_opti9xx_write_mask(struct snd_opti9xx *chip,
+		unsigned char reg, unsigned char value, unsigned char mask)
+{
+	unsigned char oldval = snd_opti9xx_read(chip, reg);
 
+	snd_opti9xx_write(chip, reg, (oldval & ~mask) | (value & mask));
+}
 
 static int snd_opti9xx_configure(struct snd_opti9xx *chip,
 					   long port,

[PATCH 4.19 27/37] nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl

[Greg Kroah-Hartman]

From: Andreas Gruenbacher <agruenba@redhat.com>

commit 7648f939cb919b9d15c21fff8cd9eba908d595dc upstream.

nfs3_set_acl keeps track of the acl it allocated locally to determine if an acl
needs to be released at the end.  This results in a memory leak when the
function allocates an acl as well as a default acl.  Fix by releasing acls
that differ from the acl originally passed into nfs3_set_acl.

Fixes: b7fa0554cf1b ("[PATCH] NFS: Add support for NFSv3 ACLs")
Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/nfs/nfs3acl.c |   22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)

--- a/fs/nfs/nfs3acl.c
+++ b/fs/nfs/nfs3acl.c
@@ -255,37 +255,45 @@ int nfs3_proc_setacls(struct inode *inod
 
 int nfs3_set_acl(struct inode *inode, struct posix_acl *acl, int type)
 {
-	struct posix_acl *alloc = NULL, *dfacl = NULL;
+	struct posix_acl *orig = acl, *dfacl = NULL, *alloc;
 	int status;
 
 	if (S_ISDIR(inode->i_mode)) {
 		switch(type) {
 		case ACL_TYPE_ACCESS:
-			alloc = dfacl = get_acl(inode, ACL_TYPE_DEFAULT);
+			alloc = get_acl(inode, ACL_TYPE_DEFAULT);
 			if (IS_ERR(alloc))
 				goto fail;
+			dfacl = alloc;
 			break;
 
 		case ACL_TYPE_DEFAULT:
-			dfacl = acl;
-			alloc = acl = get_acl(inode, ACL_TYPE_ACCESS);
+			alloc = get_acl(inode, ACL_TYPE_ACCESS);
 			if (IS_ERR(alloc))
 				goto fail;
+			dfacl = acl;
+			acl = alloc;
 			break;
 		}
 	}
 
 	if (acl == NULL) {
-		alloc = acl = posix_acl_from_mode(inode->i_mode, GFP_KERNEL);
+		alloc = posix_acl_from_mode(inode->i_mode, GFP_KERNEL);
 		if (IS_ERR(alloc))
 			goto fail;
+		acl = alloc;
 	}
 	status = __nfs3_proc_setacls(inode, acl, dfacl);
-	posix_acl_release(alloc);
+out:
+	if (acl != orig)
+		posix_acl_release(acl);
+	if (dfacl != orig)
+		posix_acl_release(dfacl);
 	return status;
 
 fail:
-	return PTR_ERR(alloc);
+	status = PTR_ERR(alloc);
+	goto out;
 }
 
 const struct xattr_handler *nfs3_xattr_handlers[] = {

[PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Greg Kroah-Hartman]

From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

commit b9f960201249f20deea586b4ec814669b4c6b1c0 upstream.

Under some circumstances, i.e. when test is still running and about to
time out and user runs, for example,

	grep -H . /sys/module/dmatest/parameters/*

the iterations parameter is not respected and test is going on and on until
user gives

	echo 0 > /sys/module/dmatest/parameters/run

This is not what expected.

The history of this bug is interesting. I though that the commit
  2d88ce76eb98 ("dmatest: add a 'wait' parameter")
is a culprit, but looking closer to the code I think it simple revealed the
broken logic from the day one, i.e. in the commit
  0a2ff57d6fba ("dmaengine: dmatest: add a maximum number of test iterations")
which adds iterations parameter.

So, to the point, the conditional of checking the thread to be stopped being
first part of conjunction logic prevents to check iterations. Thus, we have to
always check both conditions to be able to stop after given iterations.

Since it wasn't visible before second commit appeared, I add a respective
Fixes tag.

Fixes: 2d88ce76eb98 ("dmatest: add a 'wait' parameter")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/dma/dmatest.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -567,8 +567,8 @@ static int dmatest_func(void *data)
 	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
 
 	ktime = ktime_get();
-	while (!kthread_should_stop()
-	       && !(params->iterations && total_tests >= params->iterations)) {
+	while (!(kthread_should_stop() ||
+	       (params->iterations && total_tests >= params->iterations))) {
 		struct dma_async_tx_descriptor *tx = NULL;
 		struct dmaengine_unmap_data *um;
 		dma_addr_t *dsts;

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1416 bytes --]

Hi!

> So, to the point, the conditional of checking the thread to be stopped being
> first part of conjunction logic prevents to check iterations. Thus, we have to
> always check both conditions to be able to stop after given
> iterations.

I ... don't understand. AFAICT the code is equivalent. Both && and ||
operators permit "short" execution... but second part of expression
has no sideeffects, so...

> @@ -567,8 +567,8 @@ static int dmatest_func(void *data)
>  	flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
>  
>  	ktime = ktime_get();
> -	while (!kthread_should_stop()
> -	       && !(params->iterations && total_tests >= params->iterations)) {
> +	while (!(kthread_should_stop() ||
> +	       (params->iterations && total_tests >= params->iterations))) {
>  		struct dma_async_tx_descriptor *tx = NULL;
>  		struct dmaengine_unmap_data *um;
>  		dma_addr_t *dsts;

let a = kthread_should_stop()
let b = (params->iterations && total_tests >= params->iterations)

You are changing !a & !b into !(a | b). But that's equivalent
expression. I hate to admit, but I had to draw truth table to prove
that.

!a & !b   0 0 -> 1
       	  else -> 0

!(a | b)  0 0 -> 1
     	   else -> 0
	   
What am I missing?

Best regards,
								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Andy Shevchenko]

On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > So, to the point, the conditional of checking the thread to be stopped being
> > first part of conjunction logic prevents to check iterations. Thus, we have to
> > always check both conditions to be able to stop after given
> > iterations.
>
> I ... don't understand. AFAICT the code is equivalent. Both && and ||
> operators permit "short" execution... but second part of expression
> has no sideeffects, so...

..

> You are changing !a & !b into !(a | b). But that's equivalent
> expression. I hate to admit, but I had to draw truth table to prove
> that.
>
> !a & !b   0 0 -> 1
>           else -> 0
>
> !(a | b)  0 0 -> 1
>            else -> 0
>
> What am I missing?

Basic stuff. Compiler doesn't consider second part of conjunction when
first one (see operator precedence) is already false, so, it means:

a & b
0   x -> false
1   0 -> false
1   1 -> true

x is not being considered at all. So, logically it's equivalent,
run-time it's not.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1735 bytes --]

On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > So, to the point, the conditional of checking the thread to be stopped being
> > > first part of conjunction logic prevents to check iterations. Thus, we have to
> > > always check both conditions to be able to stop after given
> > > iterations.
> >
> > I ... don't understand. AFAICT the code is equivalent. Both && and ||
> > operators permit "short" execution... but second part of expression
> > has no sideeffects, so...
> 
> ..
> 
> > You are changing !a & !b into !(a | b). But that's equivalent
> > expression. I hate to admit, but I had to draw truth table to prove
> > that.
...
> > What am I missing?
> 
> Basic stuff. Compiler doesn't consider second part of conjunction when
> first one (see operator precedence) is already false, so, it means:
> 
> a & b
> 0   x -> false
> 1   0 -> false
> 1   1 -> true
> 
> x is not being considered at all. So, logically it's equivalent,
> run-time it's not.

Yeah, I pointed that out above. Both && and || permit short
execution. But that does not matter, as neither "params->iterations"
nor "total_tests >= params->iterations" have side effects.

Where is the runtime difference?

-       while (!kthread_should_stop()
-              && !(params->iterations && total_tests >=
-              params->iterations)) {
+       while (!(kthread_should_stop() ||
+              (params->iterations && total_tests >= params->iterations))) {

	       			      		     		Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Andy Shevchenko]

On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
> On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > > So, to the point, the conditional of checking the thread to be stopped being
> > > > first part of conjunction logic prevents to check iterations. Thus, we have to
> > > > always check both conditions to be able to stop after given
> > > > iterations.
> > >
> > > I ... don't understand. AFAICT the code is equivalent. Both && and ||
> > > operators permit "short" execution... but second part of expression
> > > has no sideeffects, so...
> >
> > ..
> >
> > > You are changing !a & !b into !(a | b). But that's equivalent
> > > expression. I hate to admit, but I had to draw truth table to prove
> > > that.
> ...
> > > What am I missing?
> >
> > Basic stuff. Compiler doesn't consider second part of conjunction when
> > first one (see operator precedence) is already false, so, it means:
> >
> > a & b
> > 0   x -> false
> > 1   0 -> false
> > 1   1 -> true
> >
> > x is not being considered at all. So, logically it's equivalent,
> > run-time it's not.
>
> Yeah, I pointed that out above. Both && and || permit short
> execution. But that does not matter, as neither "params->iterations"
> nor "total_tests >= params->iterations" have side effects.
>
> Where is the runtime difference?

We have to check *both* conditions. If we don't check iterations, we
just wait indefinitely until somebody tells us to stop.
Everything in the commit message and mentioned there commit IDs which
you may check.

> -       while (!kthread_should_stop()
> -              && !(params->iterations && total_tests >=
> -              params->iterations)) {
> +       while (!(kthread_should_stop() ||
> +              (params->iterations && total_tests >= params->iterations))) {

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2809 bytes --]

On Tue 2020-05-05 16:19:11, Andy Shevchenko wrote:
> On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
> > On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> > > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > > > So, to the point, the conditional of checking the thread to be stopped being
> > > > > first part of conjunction logic prevents to check iterations. Thus, we have to
> > > > > always check both conditions to be able to stop after given
> > > > > iterations.
> > > >
> > > > I ... don't understand. AFAICT the code is equivalent. Both && and ||
> > > > operators permit "short" execution... but second part of expression
> > > > has no sideeffects, so...
> > >
> > > ..
> > >
> > > > You are changing !a & !b into !(a | b). But that's equivalent
> > > > expression. I hate to admit, but I had to draw truth table to prove
> > > > that.
> > ...
> > > > What am I missing?
> > >
> > > Basic stuff. Compiler doesn't consider second part of conjunction when
> > > first one (see operator precedence) is already false, so, it means:
> > >
> > > a & b
> > > 0   x -> false
> > > 1   0 -> false
> > > 1   1 -> true
> > >
> > > x is not being considered at all. So, logically it's equivalent,
> > > run-time it's not.
> >
> > Yeah, I pointed that out above. Both && and || permit short
> > execution. But that does not matter, as neither "params->iterations"
> > nor "total_tests >= params->iterations" have side effects.
> >
> > Where is the runtime difference?
> 
> We have to check *both* conditions. If we don't check iterations, we
> just wait indefinitely until somebody tells us to stop.
> Everything in the commit message and mentioned there commit IDs which
> you may check.

No.

If kthread_should_stop() is true, we break the loop. Both old code and
new code does that. Neither old nor new code checks the
"params->iterations && total_tests >=dparams->iterations" condition,
as both && and || do short execution).

If you wanted both conditions to always evaluate, you'd have to do

#       while (!kthread_should_stop()
#              & !(params->iterations && total_tests >=
#              params->iterations)) {

(note && -> &). But, again, there's no reason to do that, as second
part of expression does not have side effects.

> > -       while (!kthread_should_stop()
> > -              && !(params->iterations && total_tests >=
> > -              params->iterations)) {
> > +       while (!(kthread_should_stop() ||
> > +              (params->iterations && total_tests >= params->iterations))) {

Best regards,
								Pavel

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Andy Shevchenko]

On Tue, May 5, 2020 at 4:37 PM Pavel Machek <pavel@denx.de> wrote:
> On Tue 2020-05-05 16:19:11, Andy Shevchenko wrote:
> > On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
> > > On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> > > > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > > > > So, to the point, the conditional of checking the thread to be stopped being
> > > > > > first part of conjunction logic prevents to check iterations. Thus, we have to
> > > > > > always check both conditions

vvv
>>>>>> to be able to stop after given iterations.
^^^

...

> > > Yeah, I pointed that out above. Both && and || permit short
> > > execution. But that does not matter, as neither "params->iterations"
> > > nor "total_tests >= params->iterations" have side effects.
> > >
> > > Where is the runtime difference?
> >
> > We have to check *both* conditions. If we don't check iterations, we
> > just wait indefinitely until somebody tells us to stop.
> > Everything in the commit message and mentioned there commit IDs which
> > you may check.
>
> No.

Yes. Please, read carefully the commit message (for your convenience I
emphasized above). I don't want to spend time on this basics stuff
anymore.

> If kthread_should_stop() is true, we break the loop. Both old code and
> new code does that. Neither old nor new code checks the
> "params->iterations && total_tests >=dparams->iterations" condition,
> as both && and || do short execution).
>
> If you wanted both conditions to always evaluate, you'd have to do
>
> #       while (!kthread_should_stop()
> #              & !(params->iterations && total_tests >=
> #              params->iterations)) {
>
> (note && -> &). But, again, there's no reason to do that, as second
> part of expression does not have side effects.

It fixes a bug in the code, try with and without this change. (I can
reproduce it here)

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1933 bytes --]

On Tue 2020-05-05 17:05:37, Andy Shevchenko wrote:
> On Tue, May 5, 2020 at 4:37 PM Pavel Machek <pavel@denx.de> wrote:
> > On Tue 2020-05-05 16:19:11, Andy Shevchenko wrote:
> > > On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
> > > > On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> > > > > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > > > > > So, to the point, the conditional of checking the thread to be stopped being
> > > > > > > first part of conjunction logic prevents to check iterations. Thus, we have to
> > > > > > > always check both conditions
> 
> vvv
> >>>>>> to be able to stop after given iterations.
> ^^^

_If_ you are already stopping due to kthread_should_stop(), you don't
need to check iterations.

If you are not stopping, iterations are always checked.

No, the new code does not "always check both conditions" as you claim.

> Yes. Please, read carefully the commit message (for your convenience I
> emphasized above). I don't want to spend time on this basics stuff
> anymore.

You may want to go through the basics once more. The change clearly
does not do what you said it does; in fact, it does not do anything.

> > If you wanted both conditions to always evaluate, you'd have to do
> >
> > #       while (!kthread_should_stop()
> > #              & !(params->iterations && total_tests >=
> > #              params->iterations)) {
> >
> > (note && -> &). But, again, there's no reason to do that, as second
> > part of expression does not have side effects.
> 
> It fixes a bug in the code, try with and without this change. (I can
> reproduce it here)

I'm not sure if you made mistake during testing, or if you have buggy
compiler or what...
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Sasha Levin]

On Tue, May 05, 2020 at 05:05:37PM +0300, Andy Shevchenko wrote:
>On Tue, May 5, 2020 at 4:37 PM Pavel Machek <pavel@denx.de> wrote:
>> On Tue 2020-05-05 16:19:11, Andy Shevchenko wrote:
>> > On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
>> > > On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
>> > > > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
>> > > Yeah, I pointed that out above. Both && and || permit short
>> > > execution. But that does not matter, as neither "params->iterations"
>> > > nor "total_tests >= params->iterations" have side effects.
>> > >
>> > > Where is the runtime difference?
>> >
>> > We have to check *both* conditions. If we don't check iterations, we
>> > just wait indefinitely until somebody tells us to stop.
>> > Everything in the commit message and mentioned there commit IDs which
>> > you may check.
>>
>> No.
>
>Yes. Please, read carefully the commit message (for your convenience I
>emphasized above). I don't want to spend time on this basics stuff
>anymore.

I'm a bit confused about this too. Maybe it's too early in the morning,
so I wrote this little test program:

#include <stdio.h>
#include <stdlib.h>

int main(int argc, char *argv[])
{
        int a = atoi(argv[1]);
        int b = atoi(argv[2]);

        if (!a && !b)
                printf("A");
        else
                printf("B");

        if (!(a || b))
                printf("A");
        else
                printf("B");

        printf("\n");

        return 0;
}

Andy, could you give an example of two values which will print something
other than "AA" or "BB"?

Heck, gcc even compiles these two conditions the same way:

        if (!a && !b)
    11a8:       83 7d f8 00             cmpl   $0x0,-0x8(%rbp)
    11ac:       75 12                   jne    11c0 <main+0x57>
    11ae:       83 7d fc 00             cmpl   $0x0,-0x4(%rbp)
    11b2:       75 0c                   jne    11c0 <main+0x57>
                printf("A");
    11b4:       bf 41 00 00 00          mov    $0x41,%edi
    11b9:       e8 a2 fe ff ff          callq  1060 <putchar@plt>
    11be:       eb 0a                   jmp    11ca <main+0x61>
        else
                printf("B");
    11c0:       bf 42 00 00 00          mov    $0x42,%edi
    11c5:       e8 96 fe ff ff          callq  1060 <putchar@plt>

        if (!(a || b))
    11ca:       83 7d f8 00             cmpl   $0x0,-0x8(%rbp)
    11ce:       75 12                   jne    11e2 <main+0x79>
    11d0:       83 7d fc 00             cmpl   $0x0,-0x4(%rbp)
    11d4:       75 0c                   jne    11e2 <main+0x79>
                printf("A");
    11d6:       bf 41 00 00 00          mov    $0x41,%edi
    11db:       e8 80 fe ff ff          callq  1060 <putchar@plt>
    11e0:       eb 0a                   jmp    11ec <main+0x83>
        else
                printf("B");
    11e2:       bf 42 00 00 00          mov    $0x42,%edi
    11e7:       e8 74 fe ff ff          callq  1060 <putchar@plt>

-- 
Thanks,
Sasha

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 2437 bytes --]

On Tue 2020-05-05 11:32:27, Sasha Levin wrote:
> On Tue, May 05, 2020 at 05:05:37PM +0300, Andy Shevchenko wrote:
> > On Tue, May 5, 2020 at 4:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > On Tue 2020-05-05 16:19:11, Andy Shevchenko wrote:
> > > > On Tue, May 5, 2020 at 3:58 PM Pavel Machek <pavel@denx.de> wrote:
> > > > > On Tue 2020-05-05 15:51:16, Andy Shevchenko wrote:
> > > > > > On Tue, May 5, 2020 at 3:37 PM Pavel Machek <pavel@denx.de> wrote:
> > > > > Yeah, I pointed that out above. Both && and || permit short
> > > > > execution. But that does not matter, as neither "params->iterations"
> > > > > nor "total_tests >= params->iterations" have side effects.
> > > > >
> > > > > Where is the runtime difference?
> > > >
> > > > We have to check *both* conditions. If we don't check iterations, we
> > > > just wait indefinitely until somebody tells us to stop.
> > > > Everything in the commit message and mentioned there commit IDs which
> > > > you may check.
> > > 
> > > No.
> > 
> > Yes. Please, read carefully the commit message (for your convenience I
> > emphasized above). I don't want to spend time on this basics stuff
> > anymore.
> 
> I'm a bit confused about this too. Maybe it's too early in the morning,
> so I wrote this little test program:
> 
> #include <stdio.h>
> #include <stdlib.h>
> 
> int main(int argc, char *argv[])
> {
>        int a = atoi(argv[1]);
>        int b = atoi(argv[2]);
> 
>        if (!a && !b)
>                printf("A");
>        else
>                printf("B");
> 
>        if (!(a || b))
>                printf("A");
>        else
>                printf("B");
> 
>        printf("\n");
> 
>        return 0;
> }
> 
> Andy, could you give an example of two values which will print something
> other than "AA" or "BB"?

The issue here is "sideffects". Does b have to be evaluated at all?
There is no difference between

      int a, b;
      if (a && b)

and

	if ((!!a) & (!!b))
.

But there would be difference between

      int a, b;
        if (a && b++)

and
	if ((!!a) & (!!(b++)))

But:

1) && and || behave same way w.r.t. side effects

2) in the patch we are talking about b has no important side effects

Best regards,
								Pavel
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 195 bytes --]

Re: [PATCH 4.19 28/37] dmaengine: dmatest: Fix iteration non-stop logic

[Andy Shevchenko]

On Tue, May 5, 2020 at 6:57 PM Pavel Machek <pavel@denx.de> wrote:
> On Tue 2020-05-05 11:32:27, Sasha Levin wrote:
> > On Tue, May 05, 2020 at 05:05:37PM +0300, Andy Shevchenko wrote:

...

> > I'm a bit confused about this too. Maybe it's too early in the morning,
> > so I wrote this little test program:
> >
> > #include <stdio.h>
> > #include <stdlib.h>
> >
> > int main(int argc, char *argv[])
> > {
> >        int a = atoi(argv[1]);
> >        int b = atoi(argv[2]);
> >
> >        if (!a && !b)
> >                printf("A");
> >        else
> >                printf("B");
> >
> >        if (!(a || b))
> >                printf("A");
> >        else
> >                printf("B");
> >
> >        printf("\n");
> >
> >        return 0;
> > }
> >
> > Andy, could you give an example of two values which will print something
> > other than "AA" or "BB"?
>
> The issue here is "sideffects". Does b have to be evaluated at all?
> There is no difference between
>
>       int a, b;
>       if (a && b)
>
> and
>
>         if ((!!a) & (!!b))
> .
>
> But there would be difference between
>
>       int a, b;
>         if (a && b++)
>
> and
>         if ((!!a) & (!!(b++)))
>
> But:
>
> 1) && and || behave same way w.r.t. side effects
>
> 2) in the patch we are talking about b has no important side effects

I have to admit that this seems like a luck and the real issue somewhere else.
Definitely another test should be performed.

Thank you, Pavel, for pointing this out.

-- 
With Best Regards,
Andy Shevchenko

[PATCH 4.19 29/37] selinux: properly handle multiple messages in selinux_netlink_send()

[Greg Kroah-Hartman]

From: Paul Moore <paul@paul-moore.com>

commit fb73974172ffaaf57a7c42f35424d9aece1a5af6 upstream.

Fix the SELinux netlink_send hook to properly handle multiple netlink
messages in a single sk_buff; each message is parsed and subject to
SELinux access control.  Prior to this patch, SELinux only inspected
the first message in the sk_buff.

Cc: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 security/selinux/hooks.c |   70 ++++++++++++++++++++++++++++++-----------------
 1 file changed, 45 insertions(+), 25 deletions(-)

--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -5595,40 +5595,60 @@ static int selinux_tun_dev_open(void *se
 
 static int selinux_nlmsg_perm(struct sock *sk, struct sk_buff *skb)
 {
-	int err = 0;
-	u32 perm;
+	int rc = 0;
+	unsigned int msg_len;
+	unsigned int data_len = skb->len;
+	unsigned char *data = skb->data;
 	struct nlmsghdr *nlh;
 	struct sk_security_struct *sksec = sk->sk_security;
+	u16 sclass = sksec->sclass;
+	u32 perm;
 
-	if (skb->len < NLMSG_HDRLEN) {
-		err = -EINVAL;
-		goto out;
-	}
-	nlh = nlmsg_hdr(skb);
+	while (data_len >= nlmsg_total_size(0)) {
+		nlh = (struct nlmsghdr *)data;
 
-	err = selinux_nlmsg_lookup(sksec->sclass, nlh->nlmsg_type, &perm);
-	if (err) {
-		if (err == -EINVAL) {
+		/* NOTE: the nlmsg_len field isn't reliably set by some netlink
+		 *       users which means we can't reject skb's with bogus
+		 *       length fields; our solution is to follow what
+		 *       netlink_rcv_skb() does and simply skip processing at
+		 *       messages with length fields that are clearly junk
+		 */
+		if (nlh->nlmsg_len < NLMSG_HDRLEN || nlh->nlmsg_len > data_len)
+			return 0;
+
+		rc = selinux_nlmsg_lookup(sclass, nlh->nlmsg_type, &perm);
+		if (rc == 0) {
+			rc = sock_has_perm(sk, perm);
+			if (rc)
+				return rc;
+		} else if (rc == -EINVAL) {
+			/* -EINVAL is a missing msg/perm mapping */
 			pr_warn_ratelimited("SELinux: unrecognized netlink"
-			       " message: protocol=%hu nlmsg_type=%hu sclass=%s"
-			       " pig=%d comm=%s\n",
-			       sk->sk_protocol, nlh->nlmsg_type,
-			       secclass_map[sksec->sclass - 1].name,
-			       task_pid_nr(current), current->comm);
-			if (!enforcing_enabled(&selinux_state) ||
-			    security_get_allow_unknown(&selinux_state))
-				err = 0;
+				" message: protocol=%hu nlmsg_type=%hu sclass=%s"
+				" pid=%d comm=%s\n",
+				sk->sk_protocol, nlh->nlmsg_type,
+				secclass_map[sclass - 1].name,
+				task_pid_nr(current), current->comm);
+			if (enforcing_enabled(&selinux_state) &&
+			    !security_get_allow_unknown(&selinux_state))
+				return rc;
+			rc = 0;
+		} else if (rc == -ENOENT) {
+			/* -ENOENT is a missing socket/class mapping, ignore */
+			rc = 0;
+		} else {
+			return rc;
 		}
 
-		/* Ignore */
-		if (err == -ENOENT)
-			err = 0;
-		goto out;
+		/* move to the next message after applying netlink padding */
+		msg_len = NLMSG_ALIGN(nlh->nlmsg_len);
+		if (msg_len >= data_len)
+			return 0;
+		data_len -= msg_len;
+		data += msg_len;
 	}
 
-	err = sock_has_perm(sk, perm);
-out:
-	return err;
+	return rc;
 }
 
 #ifdef CONFIG_NETFILTER

[PATCH 4.19 30/37] btrfs: fix partial loss of prealloc extent past i_size after fsync

[Greg Kroah-Hartman]

From: Filipe Manana <fdmanana@suse.com>

commit f135cea30de5f74d5bfb5116682073841fb4af8f upstream.

When we have an inode with a prealloc extent that starts at an offset
lower than the i_size and there is another prealloc extent that starts at
an offset beyond i_size, we can end up losing part of the first prealloc
extent (the part that starts at i_size) and have an implicit hole if we
fsync the file and then have a power failure.

Consider the following example with comments explaining how and why it
happens.

  $ mkfs.btrfs -f /dev/sdb
  $ mount /dev/sdb /mnt

  # Create our test file with 2 consecutive prealloc extents, each with a
  # size of 128Kb, and covering the range from 0 to 256Kb, with a file
  # size of 0.
  $ xfs_io -f -c "falloc -k 0 128K" /mnt/foo
  $ xfs_io -c "falloc -k 128K 128K" /mnt/foo

  # Fsync the file to record both extents in the log tree.
  $ xfs_io -c "fsync" /mnt/foo

  # Now do a redudant extent allocation for the range from 0 to 64Kb.
  # This will merely increase the file size from 0 to 64Kb. Instead we
  # could also do a truncate to set the file size to 64Kb.
  $ xfs_io -c "falloc 0 64K" /mnt/foo

  # Fsync the file, so we update the inode item in the log tree with the
  # new file size (64Kb). This also ends up setting the number of bytes
  # for the first prealloc extent to 64Kb. This is done by the truncation
  # at btrfs_log_prealloc_extents().
  # This means that if a power failure happens after this, a write into
  # the file range 64Kb to 128Kb will not use the prealloc extent and
  # will result in allocation of a new extent.
  $ xfs_io -c "fsync" /mnt/foo

  # Now set the file size to 256K with a truncate and then fsync the file.
  # Since no changes happened to the extents, the fsync only updates the
  # i_size in the inode item at the log tree. This results in an implicit
  # hole for the file range from 64Kb to 128Kb, something which fsck will
  # complain when not using the NO_HOLES feature if we replay the log
  # after a power failure.
  $ xfs_io -c "truncate 256K" -c "fsync" /mnt/foo

So instead of always truncating the log to the inode's current i_size at
btrfs_log_prealloc_extents(), check first if there's a prealloc extent
that starts at an offset lower than the i_size and with a length that
crosses the i_size - if there is one, just make sure we truncate to a
size that corresponds to the end offset of that prealloc extent, so
that we don't lose the part of that extent that starts at i_size if a
power failure happens.

A test case for fstests follows soon.

Fixes: 31d11b83b96f ("Btrfs: fix duplicate extents after fsync of file with prealloc extents")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/btrfs/tree-log.c |   43 ++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 40 insertions(+), 3 deletions(-)

--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -4182,6 +4182,9 @@ static int btrfs_log_prealloc_extents(st
 	const u64 ino = btrfs_ino(inode);
 	struct btrfs_path *dst_path = NULL;
 	bool dropped_extents = false;
+	u64 truncate_offset = i_size;
+	struct extent_buffer *leaf;
+	int slot;
 	int ins_nr = 0;
 	int start_slot;
 	int ret;
@@ -4196,9 +4199,43 @@ static int btrfs_log_prealloc_extents(st
 	if (ret < 0)
 		goto out;
 
+	/*
+	 * We must check if there is a prealloc extent that starts before the
+	 * i_size and crosses the i_size boundary. This is to ensure later we
+	 * truncate down to the end of that extent and not to the i_size, as
+	 * otherwise we end up losing part of the prealloc extent after a log
+	 * replay and with an implicit hole if there is another prealloc extent
+	 * that starts at an offset beyond i_size.
+	 */
+	ret = btrfs_previous_item(root, path, ino, BTRFS_EXTENT_DATA_KEY);
+	if (ret < 0)
+		goto out;
+
+	if (ret == 0) {
+		struct btrfs_file_extent_item *ei;
+
+		leaf = path->nodes[0];
+		slot = path->slots[0];
+		ei = btrfs_item_ptr(leaf, slot, struct btrfs_file_extent_item);
+
+		if (btrfs_file_extent_type(leaf, ei) ==
+		    BTRFS_FILE_EXTENT_PREALLOC) {
+			u64 extent_end;
+
+			btrfs_item_key_to_cpu(leaf, &key, slot);
+			extent_end = key.offset +
+				btrfs_file_extent_num_bytes(leaf, ei);
+
+			if (extent_end > i_size)
+				truncate_offset = extent_end;
+		}
+	} else {
+		ret = 0;
+	}
+
 	while (true) {
-		struct extent_buffer *leaf = path->nodes[0];
-		int slot = path->slots[0];
+		leaf = path->nodes[0];
+		slot = path->slots[0];
 
 		if (slot >= btrfs_header_nritems(leaf)) {
 			if (ins_nr > 0) {
@@ -4236,7 +4273,7 @@ static int btrfs_log_prealloc_extents(st
 				ret = btrfs_truncate_inode_items(trans,
 							 root->log_root,
 							 &inode->vfs_inode,
-							 i_size,
+							 truncate_offset,
 							 BTRFS_EXTENT_DATA_KEY);
 			} while (ret == -EAGAIN);
 			if (ret)

[PATCH 4.19 31/37] btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info

[Greg Kroah-Hartman]

From: Qu Wenruo <wqu@suse.com>

commit fcc99734d1d4ced30167eb02e17f656735cb9928 upstream.

[BUG]
One run of btrfs/063 triggered the following lockdep warning:
  ============================================
  WARNING: possible recursive locking detected
  5.6.0-rc7-custom+ #48 Not tainted
  --------------------------------------------
  kworker/u24:0/7 is trying to acquire lock:
  ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]

  but task is already holding lock:
  ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]

  other info that might help us debug this:
   Possible unsafe locking scenario:

         CPU0
         ----
    lock(sb_internal#2);
    lock(sb_internal#2);

   *** DEADLOCK ***

   May be due to missing lock nesting notation

  4 locks held by kworker/u24:0/7:
   #0: ffff88817b495948 ((wq_completion)btrfs-endio-write){+.+.}, at: process_one_work+0x557/0xb80
   #1: ffff888189ea7db8 ((work_completion)(&work->normal_work)){+.+.}, at: process_one_work+0x557/0xb80
   #2: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
   #3: ffff888174ca4da8 (&fs_info->reloc_mutex){+.+.}, at: btrfs_record_root_in_trans+0x83/0xd0 [btrfs]

  stack backtrace:
  CPU: 0 PID: 7 Comm: kworker/u24:0 Not tainted 5.6.0-rc7-custom+ #48
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
  Call Trace:
   dump_stack+0xc2/0x11a
   __lock_acquire.cold+0xce/0x214
   lock_acquire+0xe6/0x210
   __sb_start_write+0x14e/0x290
   start_transaction+0x66c/0x890 [btrfs]
   btrfs_join_transaction+0x1d/0x20 [btrfs]
   find_free_extent+0x1504/0x1a50 [btrfs]
   btrfs_reserve_extent+0xd5/0x1f0 [btrfs]
   btrfs_alloc_tree_block+0x1ac/0x570 [btrfs]
   btrfs_copy_root+0x213/0x580 [btrfs]
   create_reloc_root+0x3bd/0x470 [btrfs]
   btrfs_init_reloc_root+0x2d2/0x310 [btrfs]
   record_root_in_trans+0x191/0x1d0 [btrfs]
   btrfs_record_root_in_trans+0x90/0xd0 [btrfs]
   start_transaction+0x16e/0x890 [btrfs]
   btrfs_join_transaction+0x1d/0x20 [btrfs]
   btrfs_finish_ordered_io+0x55d/0xcd0 [btrfs]
   finish_ordered_fn+0x15/0x20 [btrfs]
   btrfs_work_helper+0x116/0x9a0 [btrfs]
   process_one_work+0x632/0xb80
   worker_thread+0x80/0x690
   kthread+0x1a3/0x1f0
   ret_from_fork+0x27/0x50

It's pretty hard to reproduce, only one hit so far.

[CAUSE]
This is because we're calling btrfs_join_transaction() without re-using
the current running one:

btrfs_finish_ordered_io()
|- btrfs_join_transaction()		<<< Call #1
   |- btrfs_record_root_in_trans()
      |- btrfs_reserve_extent()
	 |- btrfs_join_transaction()	<<< Call #2

Normally such btrfs_join_transaction() call should re-use the existing
one, without trying to re-start a transaction.

But the problem is, in btrfs_join_transaction() call #1, we call
btrfs_record_root_in_trans() before initializing current::journal_info.

And in btrfs_join_transaction() call #2, we're relying on
current::journal_info to avoid such deadlock.

[FIX]
Call btrfs_record_root_in_trans() after we have initialized
current::journal_info.

CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/btrfs/transaction.c |   13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)

--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -572,10 +572,19 @@ again:
 	}
 
 got_it:
-	btrfs_record_root_in_trans(h, root);
-
 	if (!current->journal_info)
 		current->journal_info = h;
+
+	/*
+	 * btrfs_record_root_in_trans() needs to alloc new extents, and may
+	 * call btrfs_join_transaction() while we're also starting a
+	 * transaction.
+	 *
+	 * Thus it need to be called after current->journal_info initialized,
+	 * or we can deadlock.
+	 */
+	btrfs_record_root_in_trans(h, root);
+
 	return h;
 
 join_fail:

[PATCH 4.19 32/37] mmc: cqhci: Avoid false "cqhci: CQE stuck on" by not open-coding timeout loop

[Greg Kroah-Hartman]

From: Douglas Anderson <dianders@chromium.org>

commit b1ac62a7ac386d76968af5f374a4a7a82a35fe31 upstream.

Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another.  In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():

1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
   or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.

Rather than fixing the polling loop, use readx_poll_timeout() like
many people do.  This has been time tested to handle the corner cases.

Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/cqhci.c |   21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)

--- a/drivers/mmc/host/cqhci.c
+++ b/drivers/mmc/host/cqhci.c
@@ -13,6 +13,7 @@
 #include <linux/delay.h>
 #include <linux/highmem.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/dma-mapping.h>
 #include <linux/slab.h>
@@ -351,12 +352,16 @@ static int cqhci_enable(struct mmc_host
 /* CQHCI is idle and should halt immediately, so set a small timeout */
 #define CQHCI_OFF_TIMEOUT 100
 
+static u32 cqhci_read_ctl(struct cqhci_host *cq_host)
+{
+	return cqhci_readl(cq_host, CQHCI_CTL);
+}
+
 static void cqhci_off(struct mmc_host *mmc)
 {
 	struct cqhci_host *cq_host = mmc->cqe_private;
-	ktime_t timeout;
-	bool timed_out;
 	u32 reg;
+	int err;
 
 	if (!cq_host->enabled || !mmc->cqe_on || cq_host->recovery_halt)
 		return;
@@ -366,15 +371,9 @@ static void cqhci_off(struct mmc_host *m
 
 	cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
 
-	timeout = ktime_add_us(ktime_get(), CQHCI_OFF_TIMEOUT);
-	while (1) {
-		timed_out = ktime_compare(ktime_get(), timeout) > 0;
-		reg = cqhci_readl(cq_host, CQHCI_CTL);
-		if ((reg & CQHCI_HALT) || timed_out)
-			break;
-	}
-
-	if (timed_out)
+	err = readx_poll_timeout(cqhci_read_ctl, cq_host, reg,
+				 reg & CQHCI_HALT, 0, CQHCI_OFF_TIMEOUT);
+	if (err < 0)
 		pr_err("%s: cqhci: CQE stuck on\n", mmc_hostname(mmc));
 	else
 		pr_debug("%s: cqhci: CQE off\n", mmc_hostname(mmc));

[PATCH 4.19 33/37] mmc: sdhci-xenon: fix annoying 1.8V regulator warning

[Greg Kroah-Hartman]

From: Marek Behún <marek.behun@nic.cz>

commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream.

For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.

This causes the sdhci_start_signal_voltage_switch function to report
  1.8V regulator output did not become stable

When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.

Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.

This patch fixes this particular problem on Turris MOX.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/sdhci-xenon.c |   10 ++++++++++
 1 file changed, 10 insertions(+)

--- a/drivers/mmc/host/sdhci-xenon.c
+++ b/drivers/mmc/host/sdhci-xenon.c
@@ -238,6 +238,16 @@ static void xenon_voltage_switch(struct
 {
 	/* Wait for 5ms after set 1.8V signal enable bit */
 	usleep_range(5000, 5500);
+
+	/*
+	 * For some reason the controller's Host Control2 register reports
+	 * the bit representing 1.8V signaling as 0 when read after it was
+	 * written as 1. Subsequent read reports 1.
+	 *
+	 * Since this may cause some issues, do an empty read of the Host
+	 * Control2 register here to circumvent this.
+	 */
+	sdhci_readw(host, SDHCI_HOST_CONTROL2);
 }
 
 static const struct sdhci_ops sdhci_xenon_ops = {

[PATCH 4.19 34/37] mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllers

[Greg Kroah-Hartman]

From: Adrian Hunter <adrian.hunter@intel.com>

commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream.

BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.

This is done to avoid changing the value for different boards.

Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/sdhci-pci-core.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/mmc/host/sdhci-pci-core.c
+++ b/drivers/mmc/host/sdhci-pci-core.c
@@ -556,6 +556,9 @@ static int intel_select_drive_strength(s
 	struct sdhci_pci_slot *slot = sdhci_priv(host);
 	struct intel_host *intel_host = sdhci_pci_priv(slot);
 
+	if (!(mmc_driver_type_mask(intel_host->drv_strength) & card_drv))
+		return 0;
+
 	return intel_host->drv_strength;
 }
 

[PATCH 4.19 35/37] mmc: sdhci-msm: Enable host capabilities pertains to R1b response

[Greg Kroah-Hartman]

From: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>

commit 9d8cb58691f85cef687512262acb2c7109ee4868 upstream.

MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.

So set the below two host capabilities for qcom SDHC.
 - MMC_CAP_WAIT_WHILE_BUSY
 - MMC_CAP_NEED_RSP_BUSY

Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.

Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/sdhci-msm.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -1909,6 +1909,8 @@ static int sdhci_msm_probe(struct platfo
 		goto clk_disable;
 	}
 
+	msm_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_NEED_RSP_BUSY;
+
 	pm_runtime_get_noresume(&pdev->dev);
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);

[PATCH 4.19 36/37] mmc: meson-mx-sdio: Set MMC_CAP_WAIT_WHILE_BUSY

[Greg Kroah-Hartman]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

commit e53b868b3cf5beeaa2f851ec6740112bf4d6a8cb upstream.

The Meson SDIO controller uses the DAT0 lane for hardware busy
detection. Set MMC_CAP_WAIT_WHILE_BUSY accordingly. This fixes
the following error observed with Linux 5.7 (pre-rc-1):
  mmc1: Card stuck being busy! __mmc_poll_for_busy
  blk_update_request: I/O error, dev mmcblk1, sector 17111080 op
   0x3:(DISCARD) flags 0x0 phys_seg 1 prio class 0

Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/meson-mx-sdio.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/mmc/host/meson-mx-sdio.c
+++ b/drivers/mmc/host/meson-mx-sdio.c
@@ -573,7 +573,7 @@ static int meson_mx_mmc_add_host(struct
 	mmc->f_max = clk_round_rate(host->cfg_div_clk,
 				    clk_get_rate(host->parent_clk));
 
-	mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23;
+	mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23 | MMC_CAP_WAIT_WHILE_BUSY;
 	mmc->ops = &meson_mx_mmc_ops;
 
 	ret = mmc_of_parse(mmc);

[PATCH 4.19 37/37] mmc: meson-mx-sdio: remove the broken ->card_busy() op

[Greg Kroah-Hartman]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

commit ddca1092c4324c89cf692b5efe655aa251864b51 upstream.

The recent commit 0d84c3e6a5b2 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".

It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.

Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.

Fixes: ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/mmc/host/meson-mx-sdio.c |    9 ---------
 1 file changed, 9 deletions(-)

--- a/drivers/mmc/host/meson-mx-sdio.c
+++ b/drivers/mmc/host/meson-mx-sdio.c
@@ -360,14 +360,6 @@ static void meson_mx_mmc_request(struct
 		meson_mx_mmc_start_cmd(mmc, mrq->cmd);
 }
 
-static int meson_mx_mmc_card_busy(struct mmc_host *mmc)
-{
-	struct meson_mx_mmc_host *host = mmc_priv(mmc);
-	u32 irqc = readl(host->base + MESON_MX_SDIO_IRQC);
-
-	return !!(irqc & MESON_MX_SDIO_IRQC_FORCE_DATA_DAT_MASK);
-}
-
 static void meson_mx_mmc_read_response(struct mmc_host *mmc,
 				       struct mmc_command *cmd)
 {
@@ -509,7 +501,6 @@ static void meson_mx_mmc_timeout(struct
 static struct mmc_host_ops meson_mx_mmc_ops = {
 	.request		= meson_mx_mmc_request,
 	.set_ios		= meson_mx_mmc_set_ios,
-	.card_busy		= meson_mx_mmc_card_busy,
 	.get_cd			= mmc_gpio_get_cd,
 	.get_ro			= mmc_gpio_get_ro,
 };

RE: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Chris Paterson]

Hi Greg,

> From: stable-owner@vger.kernel.org <stable-owner@vger.kernel.org> On
> Behalf Of Greg Kroah-Hartman
> Sent: 04 May 2020 18:57
> 
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.

No build/boot issues seen for CIP configs for Linux 4.19.121-rc1 (2e3613309d93).

Build/test pipeline/logs: https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/pipelines/142506752
GitLab CI pipeline: https://gitlab.com/cip-project/cip-testing/linux-cip-pipelines/-/blob/master/trees/linux-4.19.y.yml
Relevant LAVA jobs: https://lava.ciplatform.org/scheduler/alljobs?length=25&search=2e3613#table

Kind regards, Chris

> 
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-
> 4.19.121-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
> linux-4.19.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 
> -------------
> Pseudo-Shortlog of commits:
> 
> Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>     Linux 4.19.121-rc1
> 
> Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>     mmc: meson-mx-sdio: remove the broken ->card_busy() op
> 
> Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>     mmc: meson-mx-sdio: Set MMC_CAP_WAIT_WHILE_BUSY
> 
> Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
>     mmc: sdhci-msm: Enable host capabilities pertains to R1b response
> 
> Adrian Hunter <adrian.hunter@intel.com>
>     mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllers
> 
> Marek Behún <marek.behun@nic.cz>
>     mmc: sdhci-xenon: fix annoying 1.8V regulator warning
> 
> Douglas Anderson <dianders@chromium.org>
>     mmc: cqhci: Avoid false "cqhci: CQE stuck on" by not open-coding timeout
> loop
> 
> Qu Wenruo <wqu@suse.com>
>     btrfs: transaction: Avoid deadlock due to bad initialization timing of
> fs_info::journal_info
> 
> Filipe Manana <fdmanana@suse.com>
>     btrfs: fix partial loss of prealloc extent past i_size after fsync
> 
> Paul Moore <paul@paul-moore.com>
>     selinux: properly handle multiple messages in selinux_netlink_send()
> 
> Andy Shevchenko <andriy.shevchenko@linux.intel.com>
>     dmaengine: dmatest: Fix iteration non-stop logic
> 
> Andreas Gruenbacher <agruenba@redhat.com>
>     nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl
> 
> Arnd Bergmann <arnd@arndb.de>
>     ALSA: opti9xx: shut up gcc-10 range warning
> 
> Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
>     iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system
> 
> David Disseldorp <ddiss@suse.de>
>     scsi: target/iblock: fix WRITE SAME zeroing
> 
> Tang Bin <tangbin@cmss.chinamobile.com>
>     iommu/qcom: Fix local_base status check
> 
> Sean Christopherson <sean.j.christopherson@intel.com>
>     vfio/type1: Fix VA->PA translation for PFNMAP VMAs in vaddr_get_pfn()
> 
> Yan Zhao <yan.y.zhao@intel.com>
>     vfio: avoid possible overflow in vfio_iommu_type1_pin_pages
> 
> Leon Romanovsky <leon@kernel.org>
>     RDMA/core: Fix race between destroy and release FD object
> 
> Leon Romanovsky <leon@kernel.org>
>     RDMA/core: Prevent mixed use of FDs between shared ufiles
> 
> Alaa Hleihel <alaa@mellanox.com>
>     RDMA/mlx4: Initialize ib_spec on the stack
> 
> Aharon Landau <aharonl@mellanox.com>
>     RDMA/mlx5: Set GRH fields in query QP on RoCE
> 
> Martin Wilck <mwilck@suse.com>
>     scsi: qla2xxx: check UNLOADING before posting async work
> 
> Martin Wilck <mwilck@suse.com>
>     scsi: qla2xxx: set UNLOADING before waiting for session deletion
> 
> Gabriel Krisman Bertazi <krisman@collabora.com>
>     dm multipath: use updated MPATHF_QUEUE_IO on mapping for bio-based
> mpath
> 
> Mikulas Patocka <mpatocka@redhat.com>
>     dm writecache: fix data corruption when reloading the target
> 
> Sunwook Eom <speed.eom@samsung.com>
>     dm verity fec: fix hash block number in verity_fec_decode
> 
> Dexuan Cui <decui@microsoft.com>
>     PM: hibernate: Freeze kernel threads in software_resume()
> 
> Kai-Heng Feng <kai.heng.feng@canonical.com>
>     PM: ACPI: Output correct message on target power state
> 
> Takashi Iwai <tiwai@suse.de>
>     ALSA: pcm: oss: Place the plugin buffer overflow checks correctly
> 
> Wu Bo <wubo40@huawei.com>
>     ALSA: hda/hdmi: fix without unlocked before return
> 
> Takashi Iwai <tiwai@suse.de>
>     ALSA: usb-audio: Correct a typo of NuPrime DAC-10 USB ID
> 
> Hui Wang <hui.wang@canonical.com>
>     ALSA: hda/realtek - Two front mics on a Lenovo ThinkCenter
> 
> Xiyu Yang <xiyuyang19@fudan.edu.cn>
>     btrfs: fix block group leak when removing fails
> 
> Vasily Averin <vvs@virtuozzo.com>
>     drm/qxl: qxl_release use after free
> 
> Vasily Averin <vvs@virtuozzo.com>
>     drm/qxl: qxl_release leak in qxl_hw_surface_alloc()
> 
> Vasily Averin <vvs@virtuozzo.com>
>     drm/qxl: qxl_release leak in qxl_draw_dirty_fb()
> 
> Ville Syrjälä <ville.syrjala@linux.intel.com>
>     drm/edid: Fix off-by-one in DispID DTD pixel clock
> 
> 
> -------------
> 
> Diffstat:
> 
>  Makefile                            |  4 +--
>  drivers/acpi/device_pm.c            |  4 +--
>  drivers/dma/dmatest.c               |  4 +--
>  drivers/gpu/drm/drm_edid.c          |  2 +-
>  drivers/gpu/drm/qxl/qxl_cmd.c       | 10 +++---
>  drivers/gpu/drm/qxl/qxl_display.c   |  6 ++--
>  drivers/gpu/drm/qxl/qxl_draw.c      | 13 +++----
>  drivers/gpu/drm/qxl/qxl_ioctl.c     |  5 +--
>  drivers/infiniband/core/rdma_core.c |  4 +--
>  drivers/infiniband/hw/mlx4/main.c   |  3 +-
>  drivers/infiniband/hw/mlx5/qp.c     |  4 ++-
>  drivers/iommu/amd_iommu_init.c      |  2 +-
>  drivers/iommu/qcom_iommu.c          |  5 ++-
>  drivers/md/dm-mpath.c               |  6 ++--
>  drivers/md/dm-verity-fec.c          |  2 +-
>  drivers/md/dm-writecache.c          | 52 +++++++++++++++++++--------
>  drivers/mmc/host/cqhci.c            | 21 ++++++-----
>  drivers/mmc/host/meson-mx-sdio.c    | 11 +-----
>  drivers/mmc/host/sdhci-msm.c        |  2 ++
>  drivers/mmc/host/sdhci-pci-core.c   |  3 ++
>  drivers/mmc/host/sdhci-xenon.c      | 10 ++++++
>  drivers/scsi/qla2xxx/qla_os.c       | 35 +++++++++----------
>  drivers/target/target_core_iblock.c |  2 +-
>  drivers/vfio/vfio_iommu_type1.c     |  6 ++--
>  fs/btrfs/extent-tree.c              | 16 +++++----
>  fs/btrfs/transaction.c              | 13 +++++--
>  fs/btrfs/tree-log.c                 | 43 +++++++++++++++++++++--
>  fs/nfs/nfs3acl.c                    | 22 ++++++++----
>  kernel/power/hibernate.c            |  7 ++++
>  security/selinux/hooks.c            | 70 ++++++++++++++++++++++++-------------
>  sound/core/oss/pcm_plugin.c         | 20 ++++++-----
>  sound/isa/opti9xx/miro.c            |  9 +++--
>  sound/isa/opti9xx/opti92x-ad1848.c  |  9 +++--
>  sound/pci/hda/patch_hdmi.c          |  4 ++-
>  sound/pci/hda/patch_realtek.c       |  1 +
>  sound/usb/quirks.c                  |  2 +-
>  36 files changed, 281 insertions(+), 151 deletions(-)
> 

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Greg Kroah-Hartman]

On Tue, May 05, 2020 at 07:42:23AM +0000, Chris Paterson wrote:
> Hi Greg,
> 
> > From: stable-owner@vger.kernel.org <stable-owner@vger.kernel.org> On
> > Behalf Of Greg Kroah-Hartman
> > Sent: 04 May 2020 18:57
> > 
> > This is the start of the stable review cycle for the 4.19.121 release.
> > There are 37 patches in this series, all will be posted as a response
> > to this one.  If anyone has any issues with these being applied, please
> > let me know.
> 
> No build/boot issues seen for CIP configs for Linux 4.19.121-rc1 (2e3613309d93).
> 
> Build/test pipeline/logs: https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/pipelines/142506752
> GitLab CI pipeline: https://gitlab.com/cip-project/cip-testing/linux-cip-pipelines/-/blob/master/trees/linux-4.19.y.yml
> Relevant LAVA jobs: https://lava.ciplatform.org/scheduler/alljobs?length=25&search=2e3613#table

Thanks for testing two of these and letting me know.

greg k-h

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Jon Hunter]

On 04/05/2020 18:57, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.121-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h

All tests are passing for Tegra ...

Test results for stable-v4.19:
    11 builds:	11 pass, 0 fail
    22 boots:	22 pass, 0 fail
    32 tests:	32 pass, 0 fail

Linux version:	4.19.121-rc1-g2e3613309d93
Boards tested:	tegra124-jetson-tk1, tegra186-p2771-0000,
                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra30-cardhu-a04

Cheers
Jon

-- 
nvpublic

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Jon Hunter]

On 04/05/2020 18:57, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.121-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h

All tests are passing for Tegra ...

Test results for stable-v4.19:
    11 builds:	11 pass, 0 fail
    22 boots:	22 pass, 0 fail
    32 tests:	32 pass, 0 fail

Linux version:	4.19.121-rc1-g2e3613309d93
Boards tested:	tegra124-jetson-tk1, tegra186-p2771-0000,
                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra30-cardhu-a04

Cheers
Jon

-- 
nvpublic

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Naresh Kamboju]

On Mon, 4 May 2020 at 23:32, Greg Kroah-Hartman
<gregkh@linuxfoundation.org> wrote:
>
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
>         https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.121-rc1.gz
> or in the git tree and branch at:
>         git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

NOTE:
kernel warning noticed on stable rc 4.19 and 5.4 while running
selftest bpf test cases on arm64 devices.

NETDEV WATCHDOG: eth0 (asix): transmit queue 0 timed out
- net/sched/sch_generic.c:466 dev_watchdog

ref:
https://lore.kernel.org/stable/CA+G9fYu4gE2vqSmgyYMfdMS-ZDfQiY1vhk2Jbni+wDJFjLHVKg@mail.gmail.com/T/#u

Summary
------------------------------------------------------------------------

kernel: 4.19.121-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.19.y
git commit: 2e3613309d936ae445288baa881ca1775f300f6f
git describe: v4.19.120-38-g2e3613309d93
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-4.19-oe/build/v4.19.120-38-g2e3613309d93


No regressions (compared to build v4.19.120)

No fixes (compared to build v4.19.120)

Ran 28318 total tests in the following environments and test suites.

Environments
--------------
- dragonboard-410c - arm64
- hi6220-hikey - arm64
- i386
- juno-r2 - arm64
- juno-r2-compat
- juno-r2-kasan
- nxp-ls2088
- qemu_arm
- qemu_arm64
- qemu_i386
- qemu_x86_64
- x15 - arm
- x86_64
- x86-kasan

Test Suites
-----------
* build
* install-android-platform-tools-r2600
* install-android-platform-tools-r2800
* linux-log-parser
* ltp-cap_bounds-tests
* ltp-cpuhotplug-tests
* ltp-crypto-tests
* ltp-ipc-tests
* perf
* ltp-commands-tests
* ltp-containers-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* network-basic-tests
* v4l2-compliance
* kselftest
* kselftest/drivers
* kselftest/filesystems
* kselftest/net
* kselftest/networking
* libhugetlbfs
* ltp-cve-tests
* ltp-dio-tests
* ltp-fs-tests
* ltp-io-tests
* ltp-open-posix-tests
* kvm-unit-tests
* kselftest-vsyscall-mode-native
* kselftest-vsyscall-mode-native/drivers
* kselftest-vsyscall-mode-native/filesystems
* kselftest-vsyscall-mode-native/net
* kselftest-vsyscall-mode-native/networking
* kselftest-vsyscall-mode-none
* kselftest-vsyscall-mode-none/drivers
* kselftest-vsyscall-mode-none/filesystems
* kselftest-vsyscall-mode-none/net
* kselftest-vsyscall-mode-none/networking

-- 
Linaro LKFT
https://lkft.linaro.org

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[shuah]

On 5/4/20 11:57 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.121-rc1.gz
> or in the git tree and branch at:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

Re: [PATCH 4.19 00/37] 4.19.121-rc1 review

[Guenter Roeck]

On 5/4/20 10:57 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.121 release.
> There are 37 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Wed, 06 May 2020 16:52:55 +0000.
> Anything received after that time might be too late.
> 

Build results:
	total: 155 pass: 155 fail: 0
Qemu test results:
	total: 417 pass: 417 fail: 0

Guenter