[PATCH v3 0/5] ARM: simplify handover from UEFI to decompressor

[PATCH v3 0/5] ARM: simplify handover from UEFI to decompressor

[Ard Biesheuvel]

The EFI stub in the ARM kernel runs in the context of the firmware, which
means it usually runs with the caches and MMU on. Currently, we relocate
the zImage so it appears in the first 128 MiB, disable the MMU and caches
and invoke the decompressor via its ordinary entry point. However, since we
can pass the base of DRAM directly, there is no need to relocate the zImage,
which also means there is no need to disable and re-enable the caches and
create new page tables etc.

This simplification is implemented by patch #5. Patches #1 - #4 are
prerequisite changes to permit the decompressor startup code to be invoked
past its ordinary entry point, and execute from the offset where the UEFI
firmware happened to load it.

Note that this applies onto rmk/for-next as of today.

Changes since v2:
- Set the LSB of the image address if we are entering with MMU and caches off,
  so that the decompressor will install its own page tables as it usually
  does. This might happen on U-Boot platforms that call 'bootefi' without
  enabling the caches (which technically violates the UEFI spec, but might
  be working fine today)
- Add Nico's ack to the series

Changes since v1:
- Tweak some asm sequences in #2 to fix the Thumb2 build
- Switch immediately to the new stack in #5

Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>

Ard Biesheuvel (5):
  ARM: decompressor: move headroom variable out of LC0
  ARM: decompressor: split off _edata and stack base into separate
    object
  ARM: decompressor: defer loading of the contents of the LC0 structure
  ARM: decompressor: move GOT into .data for EFI enabled builds
  ARM: decompressor: run decompressor in place if loaded via UEFI

 arch/arm/boot/compressed/head.S           | 91 ++++++++------------
 arch/arm/boot/compressed/vmlinux.lds.S    |  5 ++
 drivers/firmware/efi/libstub/arm32-stub.c | 45 ++--------
 3 files changed, 48 insertions(+), 93 deletions(-)

-- 
2.17.1

[PATCH v3 0/5] ARM: simplify handover from UEFI to decompressor

[Ard Biesheuvel]

The EFI stub in the ARM kernel runs in the context of the firmware, which
means it usually runs with the caches and MMU on. Currently, we relocate
the zImage so it appears in the first 128 MiB, disable the MMU and caches
and invoke the decompressor via its ordinary entry point. However, since we
can pass the base of DRAM directly, there is no need to relocate the zImage,
which also means there is no need to disable and re-enable the caches and
create new page tables etc.

This simplification is implemented by patch #5. Patches #1 - #4 are
prerequisite changes to permit the decompressor startup code to be invoked
past its ordinary entry point, and execute from the offset where the UEFI
firmware happened to load it.

Note that this applies onto rmk/for-next as of today.

Changes since v2:
- Set the LSB of the image address if we are entering with MMU and caches off,
  so that the decompressor will install its own page tables as it usually
  does. This might happen on U-Boot platforms that call 'bootefi' without
  enabling the caches (which technically violates the UEFI spec, but might
  be working fine today)
- Add Nico's ack to the series

Changes since v1:
- Tweak some asm sequences in #2 to fix the Thumb2 build
- Switch immediately to the new stack in #5

Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>

Ard Biesheuvel (5):
  ARM: decompressor: move headroom variable out of LC0
  ARM: decompressor: split off _edata and stack base into separate
    object
  ARM: decompressor: defer loading of the contents of the LC0 structure
  ARM: decompressor: move GOT into .data for EFI enabled builds
  ARM: decompressor: run decompressor in place if loaded via UEFI

 arch/arm/boot/compressed/head.S           | 91 ++++++++------------
 arch/arm/boot/compressed/vmlinux.lds.S    |  5 ++
 drivers/firmware/efi/libstub/arm32-stub.c | 45 ++--------
 3 files changed, 48 insertions(+), 93 deletions(-)

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/5] ARM: decompressor: move headroom variable out of LC0

[Ard Biesheuvel]

Before breaking up LC0 into different pieces, move out the variable
that is already place-relative (given that it subtracts 'restart' in
the expression) and so its value does not need to be added to the
runtime address of the LC0 symbol itself.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 2d2a42865b39..bb674febf640 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -339,7 +339,7 @@ not_angel:
 		 */
 		mov	r0, pc
 		cmp	r0, r4
-		ldrcc	r0, LC0+28
+		ldrcc	r0, .Lheadroom
 		addcc	r0, r0, pc
 		cmpcc	r4, r0
 		orrcc	r4, r4, #1		@ remember we skipped cache_on
@@ -716,9 +716,11 @@ LC0:		.word	LC0			@ r1
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
 		.word	.L_user_stack_end	@ sp
-		.word	_end - restart + 16384 + 1024*1024
 		.size	LC0, . - LC0
 
+.Lheadroom:
+		.word	_end - restart + 16384 + 1024*1024
+
 .Linflated_image_size_offset:
 		.long	(input_data_end - 4) - .
 
-- 
2.17.1

[PATCH v3 1/5] ARM: decompressor: move headroom variable out of LC0

[Ard Biesheuvel]

Before breaking up LC0 into different pieces, move out the variable
that is already place-relative (given that it subtracts 'restart' in
the expression) and so its value does not need to be added to the
runtime address of the LC0 symbol itself.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 2d2a42865b39..bb674febf640 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -339,7 +339,7 @@ not_angel:
 		 */
 		mov	r0, pc
 		cmp	r0, r4
-		ldrcc	r0, LC0+28
+		ldrcc	r0, .Lheadroom
 		addcc	r0, r0, pc
 		cmpcc	r4, r0
 		orrcc	r4, r4, #1		@ remember we skipped cache_on
@@ -716,9 +716,11 @@ LC0:		.word	LC0			@ r1
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
 		.word	.L_user_stack_end	@ sp
-		.word	_end - restart + 16384 + 1024*1024
 		.size	LC0, . - LC0
 
+.Lheadroom:
+		.word	_end - restart + 16384 + 1024*1024
+
 .Linflated_image_size_offset:
 		.long	(input_data_end - 4) - .
 
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/5] ARM: decompressor: split off _edata and stack base into separate object

[Ard Biesheuvel]

In preparation of moving the handling of the LC0 object to a later stage
in the decompressor startup code, move out _edata and the initial value
of the stack pointer, which are now used in two places, and are needed
earlier than the remaining contents of LC0.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 35 ++++++++++----------
 1 file changed, 17 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index bb674febf640..449457d00c4e 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -259,19 +259,17 @@ not_angel:
 		 * Find the start of physical memory.
 		 * Try the DTB first, if available.
 		 */
-		adr	r0, LC0
-		ldr	r1, [r0]	@ get absolute LC0
-		ldr	sp, [r0, #24]	@ get stack location
-		sub	r1, r0, r1	@ compute relocation offset
-		add	sp, sp, r1	@ apply relocation
+		adr	r0, LC1
+		ldr	sp, [r0]	@ get stack location
+		add	sp, sp, r0	@ apply relocation
 
 #ifdef CONFIG_ARM_APPENDED_DTB
 		/*
 		 * Look for an appended DTB. If found, use it and
 		 * move stack away from it.
 		 */
-		ldr	r6, [r0, #12]	@ get &_edata
-		add	r6, r6, r1	@ relocate it
+		ldr	r6, [r0, #4]	@ get &_edata
+		add	r6, r6, r0	@ relocate it
 		ldmia	r6, {r0, r5}	@ get DTB signature and size
 #ifndef __ARMEB__
 		ldr	r1, =0xedfe0dd0	@ sig is 0xd00dfeed big endian
@@ -345,22 +343,20 @@ not_angel:
 		orrcc	r4, r4, #1		@ remember we skipped cache_on
 		blcs	cache_on
 
-restart:	adr	r0, LC0
-		ldmia	r0, {r1, r2, r3, r6, r11, r12}
-		ldr	sp, [r0, #24]
+restart:	adr	r0, LC1
+		ldr	sp, [r0]
+		ldr	r6, [r0, #4]
+		add	sp, sp, r0
+		add	r6, r6, r0
 
-		/*
-		 * We might be running at a different address.  We need
-		 * to fix up various pointers.
-		 */
+		adr	r0, LC0
+		ldmia	r0, {r1, r2, r3, r11, r12}
 		sub	r0, r0, r1		@ calculate the delta offset
-		add	r6, r6, r0		@ _edata
 
 		get_inflated_image_size	r9, r10, lr
 
 #ifndef CONFIG_ZBOOT_ROM
 		/* malloc space is above the relocated stack (64k max) */
-		add	sp, sp, r0
 		add	r10, sp, #0x10000
 #else
 		/*
@@ -712,12 +708,15 @@ not_relocated:	mov	r0, #0
 LC0:		.word	LC0			@ r1
 		.word	__bss_start		@ r2
 		.word	_end			@ r3
-		.word	_edata			@ r6
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
-		.word	.L_user_stack_end	@ sp
 		.size	LC0, . - LC0
 
+		.type	LC1, #object
+LC1:		.word	.L_user_stack_end - LC1	@ sp
+		.word	_edata - LC1		@ r6
+		.size	LC1, . - LC1
+
 .Lheadroom:
 		.word	_end - restart + 16384 + 1024*1024
 
-- 
2.17.1

[PATCH v3 2/5] ARM: decompressor: split off _edata and stack base into separate object

[Ard Biesheuvel]

In preparation of moving the handling of the LC0 object to a later stage
in the decompressor startup code, move out _edata and the initial value
of the stack pointer, which are now used in two places, and are needed
earlier than the remaining contents of LC0.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 35 ++++++++++----------
 1 file changed, 17 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index bb674febf640..449457d00c4e 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -259,19 +259,17 @@ not_angel:
 		 * Find the start of physical memory.
 		 * Try the DTB first, if available.
 		 */
-		adr	r0, LC0
-		ldr	r1, [r0]	@ get absolute LC0
-		ldr	sp, [r0, #24]	@ get stack location
-		sub	r1, r0, r1	@ compute relocation offset
-		add	sp, sp, r1	@ apply relocation
+		adr	r0, LC1
+		ldr	sp, [r0]	@ get stack location
+		add	sp, sp, r0	@ apply relocation
 
 #ifdef CONFIG_ARM_APPENDED_DTB
 		/*
 		 * Look for an appended DTB. If found, use it and
 		 * move stack away from it.
 		 */
-		ldr	r6, [r0, #12]	@ get &_edata
-		add	r6, r6, r1	@ relocate it
+		ldr	r6, [r0, #4]	@ get &_edata
+		add	r6, r6, r0	@ relocate it
 		ldmia	r6, {r0, r5}	@ get DTB signature and size
 #ifndef __ARMEB__
 		ldr	r1, =0xedfe0dd0	@ sig is 0xd00dfeed big endian
@@ -345,22 +343,20 @@ not_angel:
 		orrcc	r4, r4, #1		@ remember we skipped cache_on
 		blcs	cache_on
 
-restart:	adr	r0, LC0
-		ldmia	r0, {r1, r2, r3, r6, r11, r12}
-		ldr	sp, [r0, #24]
+restart:	adr	r0, LC1
+		ldr	sp, [r0]
+		ldr	r6, [r0, #4]
+		add	sp, sp, r0
+		add	r6, r6, r0
 
-		/*
-		 * We might be running at a different address.  We need
-		 * to fix up various pointers.
-		 */
+		adr	r0, LC0
+		ldmia	r0, {r1, r2, r3, r11, r12}
 		sub	r0, r0, r1		@ calculate the delta offset
-		add	r6, r6, r0		@ _edata
 
 		get_inflated_image_size	r9, r10, lr
 
 #ifndef CONFIG_ZBOOT_ROM
 		/* malloc space is above the relocated stack (64k max) */
-		add	sp, sp, r0
 		add	r10, sp, #0x10000
 #else
 		/*
@@ -712,12 +708,15 @@ not_relocated:	mov	r0, #0
 LC0:		.word	LC0			@ r1
 		.word	__bss_start		@ r2
 		.word	_end			@ r3
-		.word	_edata			@ r6
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
-		.word	.L_user_stack_end	@ sp
 		.size	LC0, . - LC0
 
+		.type	LC1, #object
+LC1:		.word	.L_user_stack_end - LC1	@ sp
+		.word	_edata - LC1		@ r6
+		.size	LC1, . - LC1
+
 .Lheadroom:
 		.word	_end - restart + 16384 + 1024*1024
 
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/5] ARM: decompressor: defer loading of the contents of the LC0 structure

[Ard Biesheuvel]

The remaining contents of LC0 are only used after the point in the
decompressor startup code where we enter via 'wont_overwrite'. So
move the loading of the LC0 structure after it. This will allow us
to jump to wont_overwrite directly from the EFI stub, and execute
the decompressor in place at the offset it was loaded by the UEFI
firmware.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 15 ++++-----------
 1 file changed, 4 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 449457d00c4e..9dea394b286b 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -349,10 +349,6 @@ restart:	adr	r0, LC1
 		add	sp, sp, r0
 		add	r6, r6, r0
 
-		adr	r0, LC0
-		ldmia	r0, {r1, r2, r3, r11, r12}
-		sub	r0, r0, r1		@ calculate the delta offset
-
 		get_inflated_image_size	r9, r10, lr
 
 #ifndef CONFIG_ZBOOT_ROM
@@ -370,9 +366,6 @@ restart:	adr	r0, LC1
 		mov	r5, #0			@ init dtb size to 0
 #ifdef CONFIG_ARM_APPENDED_DTB
 /*
- *   r0  = delta
- *   r2  = BSS start
- *   r3  = BSS end
  *   r4  = final kernel address (possibly with LSB set)
  *   r5  = appended dtb size (still unknown)
  *   r6  = _edata
@@ -380,8 +373,6 @@ restart:	adr	r0, LC1
  *   r8  = atags/device tree pointer
  *   r9  = size of decompressed image
  *   r10 = end of this image, including  bss/stack/malloc space if non XIP
- *   r11 = GOT start
- *   r12 = GOT end
  *   sp  = stack pointer
  *
  * if there are device trees (dtb) appended to zImage, advance r10 so that the
@@ -429,7 +420,6 @@ restart:	adr	r0, LC1
 		/* temporarily relocate the stack past the DTB work space */
 		add	sp, sp, r5
 
-		stmfd	sp!, {r0-r3, ip, lr}
 		mov	r0, r8
 		mov	r1, r6
 		mov	r2, r5
@@ -448,7 +438,6 @@ restart:	adr	r0, LC1
 		mov	r2, r5
 		bleq	atags_to_fdt
 
-		ldmfd	sp!, {r0-r3, ip, lr}
 		sub	sp, sp, r5
 #endif
 
@@ -585,6 +574,10 @@ dtb_check_done:
 		mov	pc, r0
 
 wont_overwrite:
+		adr	r0, LC0
+		ldmia	r0, {r1, r2, r3, r11, r12}
+		sub	r0, r0, r1		@ calculate the delta offset
+
 /*
  * If delta is zero, we are running at the address we were linked at.
  *   r0  = delta
-- 
2.17.1

[PATCH v3 3/5] ARM: decompressor: defer loading of the contents of the LC0 structure

[Ard Biesheuvel]

The remaining contents of LC0 are only used after the point in the
decompressor startup code where we enter via 'wont_overwrite'. So
move the loading of the LC0 structure after it. This will allow us
to jump to wont_overwrite directly from the EFI stub, and execute
the decompressor in place at the offset it was loaded by the UEFI
firmware.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S | 15 ++++-----------
 1 file changed, 4 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 449457d00c4e..9dea394b286b 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -349,10 +349,6 @@ restart:	adr	r0, LC1
 		add	sp, sp, r0
 		add	r6, r6, r0
 
-		adr	r0, LC0
-		ldmia	r0, {r1, r2, r3, r11, r12}
-		sub	r0, r0, r1		@ calculate the delta offset
-
 		get_inflated_image_size	r9, r10, lr
 
 #ifndef CONFIG_ZBOOT_ROM
@@ -370,9 +366,6 @@ restart:	adr	r0, LC1
 		mov	r5, #0			@ init dtb size to 0
 #ifdef CONFIG_ARM_APPENDED_DTB
 /*
- *   r0  = delta
- *   r2  = BSS start
- *   r3  = BSS end
  *   r4  = final kernel address (possibly with LSB set)
  *   r5  = appended dtb size (still unknown)
  *   r6  = _edata
@@ -380,8 +373,6 @@ restart:	adr	r0, LC1
  *   r8  = atags/device tree pointer
  *   r9  = size of decompressed image
  *   r10 = end of this image, including  bss/stack/malloc space if non XIP
- *   r11 = GOT start
- *   r12 = GOT end
  *   sp  = stack pointer
  *
  * if there are device trees (dtb) appended to zImage, advance r10 so that the
@@ -429,7 +420,6 @@ restart:	adr	r0, LC1
 		/* temporarily relocate the stack past the DTB work space */
 		add	sp, sp, r5
 
-		stmfd	sp!, {r0-r3, ip, lr}
 		mov	r0, r8
 		mov	r1, r6
 		mov	r2, r5
@@ -448,7 +438,6 @@ restart:	adr	r0, LC1
 		mov	r2, r5
 		bleq	atags_to_fdt
 
-		ldmfd	sp!, {r0-r3, ip, lr}
 		sub	sp, sp, r5
 #endif
 
@@ -585,6 +574,10 @@ dtb_check_done:
 		mov	pc, r0
 
 wont_overwrite:
+		adr	r0, LC0
+		ldmia	r0, {r1, r2, r3, r11, r12}
+		sub	r0, r0, r1		@ calculate the delta offset
+
 /*
  * If delta is zero, we are running at the address we were linked at.
  *   r0  = delta
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/5] ARM: decompressor: move GOT into .data for EFI enabled builds

[Ard Biesheuvel]

We will be running the decompressor in place after a future patch,
instead of copying it around first. This means we no longer have to
disable and re-enable the MMU and caches either. However, this means
we will be loaded with the restricted permissions set by the UEFI
firmware, which means that we have to move the GOT table into the
data section in order for the contents to be writable by the code
itself.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/vmlinux.lds.S | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/compressed/vmlinux.lds.S b/arch/arm/boot/compressed/vmlinux.lds.S
index b247f399de71..d0619ec05705 100644
--- a/arch/arm/boot/compressed/vmlinux.lds.S
+++ b/arch/arm/boot/compressed/vmlinux.lds.S
@@ -63,9 +63,11 @@ SECTIONS
   _etext = .;
 
   .got.plt		: { *(.got.plt) }
+#ifndef CONFIG_EFI_STUB
   _got_start = .;
   .got			: { *(.got) }
   _got_end = .;
+#endif
 
   /* ensure the zImage file size is always a multiple of 64 bits */
   /* (without a dummy byte, ld just ignores the empty section) */
@@ -74,6 +76,9 @@ SECTIONS
 #ifdef CONFIG_EFI_STUB
   .data : ALIGN(4096) {
     __pecoff_data_start = .;
+    _got_start = .;
+    *(.got)
+    _got_end = .;
     /*
      * The EFI stub always executes from RAM, and runs strictly before the
      * decompressor, so we can make an exception for its r/w data, and keep it
-- 
2.17.1

[PATCH v3 4/5] ARM: decompressor: move GOT into .data for EFI enabled builds

[Ard Biesheuvel]

We will be running the decompressor in place after a future patch,
instead of copying it around first. This means we no longer have to
disable and re-enable the MMU and caches either. However, this means
we will be loaded with the restricted permissions set by the UEFI
firmware, which means that we have to move the GOT table into the
data section in order for the contents to be writable by the code
itself.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/vmlinux.lds.S | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/compressed/vmlinux.lds.S b/arch/arm/boot/compressed/vmlinux.lds.S
index b247f399de71..d0619ec05705 100644
--- a/arch/arm/boot/compressed/vmlinux.lds.S
+++ b/arch/arm/boot/compressed/vmlinux.lds.S
@@ -63,9 +63,11 @@ SECTIONS
   _etext = .;
 
   .got.plt		: { *(.got.plt) }
+#ifndef CONFIG_EFI_STUB
   _got_start = .;
   .got			: { *(.got) }
   _got_end = .;
+#endif
 
   /* ensure the zImage file size is always a multiple of 64 bits */
   /* (without a dummy byte, ld just ignores the empty section) */
@@ -74,6 +76,9 @@ SECTIONS
 #ifdef CONFIG_EFI_STUB
   .data : ALIGN(4096) {
     __pecoff_data_start = .;
+    _got_start = .;
+    *(.got)
+    _got_end = .;
     /*
      * The EFI stub always executes from RAM, and runs strictly before the
      * decompressor, so we can make an exception for its r/w data, and keep it
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/5] ARM: decompressor: run decompressor in place if loaded via UEFI

[Ard Biesheuvel]

The decompressor can load from anywhere in memory, and the only reason
the EFI stub code relocates it is to ensure it appears within the first
128 MiB of memory, so that the uncompressed kernel ends up at the right
offset in memory.

We can short circuit this, and simply jump into the decompressor startup
code at the point where it knows where the base of memory lives. This
also means there is no need to disable the MMU and caches, create new
page tables and re-enable them.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S           | 39 ++++++-----------
 drivers/firmware/efi/libstub/arm32-stub.c | 45 +++-----------------
 2 files changed, 20 insertions(+), 64 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 9dea394b286b..3e525e9325d6 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -1480,37 +1480,26 @@ reloc_code_end:
 
 #ifdef CONFIG_EFI_STUB
 ENTRY(efi_enter_kernel)
-		mov	r7, r0				@ preserve image base
-		mov	r4, r1				@ preserve DT pointer
+		mov	r4, r0			@ preserve image base
+		mov	r8, r1			@ preserve DT pointer
 
-		mov	r0, r4				@ DT start
-		add	r1, r4, r2			@ DT end
-		bl	cache_clean_flush
+		mrc	p15, 0, r0, c1, c0, 0	@ read SCTLR
+		tst	r0, #0x1		@ MMU enabled?
+		orreq	r4, r4, #1		@ set LSB if not
 
-		mov	r0, r7				@ relocated zImage
-		ldr	r1, =_edata			@ size of zImage
-		add	r1, r1, r0			@ end of zImage
+		mov	r0, r8			@ DT start
+		add	r1, r8, r2		@ DT end
 		bl	cache_clean_flush
 
-		@ The PE/COFF loader might not have cleaned the code we are
-		@ running beyond the PoU, and so calling cache_off below from
-		@ inside the PE/COFF loader allocated region is unsafe unless
-		@ we explicitly clean it to the PoC.
-		adr	r0, call_cache_fn		@ region of code we will
-		adr	r1, 0f				@ run with MMU off
-		bl	cache_clean_flush
-		bl	cache_off
+		adr	r0, 0f			@ switch to our stack
+		ldr	sp, [r0]
+		add	sp, sp, r0
 
-		@ Set parameters for booting zImage according to boot protocol
-		@ put FDT address in r2, it was returned by efi_entry()
-		@ r1 is the machine type, and r0 needs to be 0
-		mov	r0, #0
-		mov	r1, #0xFFFFFFFF
-		mov	r2, r4
-		add	r7, r7, #(__efi_start - start)
-		mov	pc, r7				@ no mode switch
+		mov	r5, #0			@ appended DTB size
+		mov	r7, #0xFFFFFFFF		@ machine ID
+		b	wont_overwrite
 ENDPROC(efi_enter_kernel)
-0:
+0:		.long	.L_user_stack_end - .
 #endif
 
 		.align
diff --git a/drivers/firmware/efi/libstub/arm32-stub.c b/drivers/firmware/efi/libstub/arm32-stub.c
index 7826553af2ba..0050d811bf20 100644
--- a/drivers/firmware/efi/libstub/arm32-stub.c
+++ b/drivers/firmware/efi/libstub/arm32-stub.c
@@ -199,14 +199,8 @@ efi_status_t handle_kernel_image(unsigned long *image_addr,
 	unsigned long kernel_base;
 	efi_status_t status;
 
-	/*
-	 * Verify that the DRAM base address is compatible with the ARM
-	 * boot protocol, which determines the base of DRAM by masking
-	 * off the low 27 bits of the address at which the zImage is
-	 * loaded. These assumptions are made by the decompressor,
-	 * before any memory map is available.
-	 */
-	kernel_base = round_up(dram_base, SZ_128M);
+	/* use a 16 MiB aligned base for the decompressed kernel */
+	kernel_base = round_up(dram_base, SZ_16M) + TEXT_OFFSET;
 
 	/*
 	 * Note that some platforms (notably, the Raspberry Pi 2) put
@@ -215,41 +209,14 @@ efi_status_t handle_kernel_image(unsigned long *image_addr,
 	 * base of the kernel image is only partially used at the moment.
 	 * (Up to 5 pages are used for the swapper page tables)
 	 */
-	kernel_base += TEXT_OFFSET - 5 * PAGE_SIZE;
-
-	status = reserve_kernel_base(kernel_base, reserve_addr, reserve_size);
+	status = reserve_kernel_base(kernel_base - 5 * PAGE_SIZE, reserve_addr,
+				     reserve_size);
 	if (status != EFI_SUCCESS) {
 		pr_efi_err("Unable to allocate memory for uncompressed kernel.\n");
 		return status;
 	}
 
-	/*
-	 * Relocate the zImage, so that it appears in the lowest 128 MB
-	 * memory window.
-	 */
-	*image_addr = (unsigned long)image->image_base;
-	*image_size = image->image_size;
-	status = efi_relocate_kernel(image_addr, *image_size, *image_size,
-				     kernel_base + MAX_UNCOMP_KERNEL_SIZE, 0, 0);
-	if (status != EFI_SUCCESS) {
-		pr_efi_err("Failed to relocate kernel.\n");
-		efi_free(*reserve_size, *reserve_addr);
-		*reserve_size = 0;
-		return status;
-	}
-
-	/*
-	 * Check to see if we were able to allocate memory low enough
-	 * in memory. The kernel determines the base of DRAM from the
-	 * address at which the zImage is loaded.
-	 */
-	if (*image_addr + *image_size > dram_base + ZIMAGE_OFFSET_LIMIT) {
-		pr_efi_err("Failed to relocate kernel, no low memory available.\n");
-		efi_free(*reserve_size, *reserve_addr);
-		*reserve_size = 0;
-		efi_free(*image_size, *image_addr);
-		*image_size = 0;
-		return EFI_LOAD_ERROR;
-	}
+	*image_addr = kernel_base;
+	*image_size = 0;
 	return EFI_SUCCESS;
 }
-- 
2.17.1

[PATCH v3 5/5] ARM: decompressor: run decompressor in place if loaded via UEFI

[Ard Biesheuvel]

The decompressor can load from anywhere in memory, and the only reason
the EFI stub code relocates it is to ensure it appears within the first
128 MiB of memory, so that the uncompressed kernel ends up at the right
offset in memory.

We can short circuit this, and simply jump into the decompressor startup
code at the point where it knows where the base of memory lives. This
also means there is no need to disable the MMU and caches, create new
page tables and re-enable them.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
---
 arch/arm/boot/compressed/head.S           | 39 ++++++-----------
 drivers/firmware/efi/libstub/arm32-stub.c | 45 +++-----------------
 2 files changed, 20 insertions(+), 64 deletions(-)

diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index 9dea394b286b..3e525e9325d6 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -1480,37 +1480,26 @@ reloc_code_end:
 
 #ifdef CONFIG_EFI_STUB
 ENTRY(efi_enter_kernel)
-		mov	r7, r0				@ preserve image base
-		mov	r4, r1				@ preserve DT pointer
+		mov	r4, r0			@ preserve image base
+		mov	r8, r1			@ preserve DT pointer
 
-		mov	r0, r4				@ DT start
-		add	r1, r4, r2			@ DT end
-		bl	cache_clean_flush
+		mrc	p15, 0, r0, c1, c0, 0	@ read SCTLR
+		tst	r0, #0x1		@ MMU enabled?
+		orreq	r4, r4, #1		@ set LSB if not
 
-		mov	r0, r7				@ relocated zImage
-		ldr	r1, =_edata			@ size of zImage
-		add	r1, r1, r0			@ end of zImage
+		mov	r0, r8			@ DT start
+		add	r1, r8, r2		@ DT end
 		bl	cache_clean_flush
 
-		@ The PE/COFF loader might not have cleaned the code we are
-		@ running beyond the PoU, and so calling cache_off below from
-		@ inside the PE/COFF loader allocated region is unsafe unless
-		@ we explicitly clean it to the PoC.
-		adr	r0, call_cache_fn		@ region of code we will
-		adr	r1, 0f				@ run with MMU off
-		bl	cache_clean_flush
-		bl	cache_off
+		adr	r0, 0f			@ switch to our stack
+		ldr	sp, [r0]
+		add	sp, sp, r0
 
-		@ Set parameters for booting zImage according to boot protocol
-		@ put FDT address in r2, it was returned by efi_entry()
-		@ r1 is the machine type, and r0 needs to be 0
-		mov	r0, #0
-		mov	r1, #0xFFFFFFFF
-		mov	r2, r4
-		add	r7, r7, #(__efi_start - start)
-		mov	pc, r7				@ no mode switch
+		mov	r5, #0			@ appended DTB size
+		mov	r7, #0xFFFFFFFF		@ machine ID
+		b	wont_overwrite
 ENDPROC(efi_enter_kernel)
-0:
+0:		.long	.L_user_stack_end - .
 #endif
 
 		.align
diff --git a/drivers/firmware/efi/libstub/arm32-stub.c b/drivers/firmware/efi/libstub/arm32-stub.c
index 7826553af2ba..0050d811bf20 100644
--- a/drivers/firmware/efi/libstub/arm32-stub.c
+++ b/drivers/firmware/efi/libstub/arm32-stub.c
@@ -199,14 +199,8 @@ efi_status_t handle_kernel_image(unsigned long *image_addr,
 	unsigned long kernel_base;
 	efi_status_t status;
 
-	/*
-	 * Verify that the DRAM base address is compatible with the ARM
-	 * boot protocol, which determines the base of DRAM by masking
-	 * off the low 27 bits of the address at which the zImage is
-	 * loaded. These assumptions are made by the decompressor,
-	 * before any memory map is available.
-	 */
-	kernel_base = round_up(dram_base, SZ_128M);
+	/* use a 16 MiB aligned base for the decompressed kernel */
+	kernel_base = round_up(dram_base, SZ_16M) + TEXT_OFFSET;
 
 	/*
 	 * Note that some platforms (notably, the Raspberry Pi 2) put
@@ -215,41 +209,14 @@ efi_status_t handle_kernel_image(unsigned long *image_addr,
 	 * base of the kernel image is only partially used at the moment.
 	 * (Up to 5 pages are used for the swapper page tables)
 	 */
-	kernel_base += TEXT_OFFSET - 5 * PAGE_SIZE;
-
-	status = reserve_kernel_base(kernel_base, reserve_addr, reserve_size);
+	status = reserve_kernel_base(kernel_base - 5 * PAGE_SIZE, reserve_addr,
+				     reserve_size);
 	if (status != EFI_SUCCESS) {
 		pr_efi_err("Unable to allocate memory for uncompressed kernel.\n");
 		return status;
 	}
 
-	/*
-	 * Relocate the zImage, so that it appears in the lowest 128 MB
-	 * memory window.
-	 */
-	*image_addr = (unsigned long)image->image_base;
-	*image_size = image->image_size;
-	status = efi_relocate_kernel(image_addr, *image_size, *image_size,
-				     kernel_base + MAX_UNCOMP_KERNEL_SIZE, 0, 0);
-	if (status != EFI_SUCCESS) {
-		pr_efi_err("Failed to relocate kernel.\n");
-		efi_free(*reserve_size, *reserve_addr);
-		*reserve_size = 0;
-		return status;
-	}
-
-	/*
-	 * Check to see if we were able to allocate memory low enough
-	 * in memory. The kernel determines the base of DRAM from the
-	 * address at which the zImage is loaded.
-	 */
-	if (*image_addr + *image_size > dram_base + ZIMAGE_OFFSET_LIMIT) {
-		pr_efi_err("Failed to relocate kernel, no low memory available.\n");
-		efi_free(*reserve_size, *reserve_addr);
-		*reserve_size = 0;
-		efi_free(*image_size, *image_addr);
-		*image_size = 0;
-		return EFI_LOAD_ERROR;
-	}
+	*image_addr = kernel_base;
+	*image_size = 0;
 	return EFI_SUCCESS;
 }
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel