All of lore.kernel.org
 help / color / mirror / Atom feed
From: Michael Walle <michael@walle.cc>
To: u-boot@lists.denx.de
Subject: [PATCH v4 03/12] phy: atheros: Clarify the configuration of the CLK_25M output pin
Date: Thu,  7 May 2020 00:11:50 +0200	[thread overview]
Message-ID: <20200506221159.1298-4-michael@walle.cc> (raw)
In-Reply-To: <20200506221159.1298-1-michael@walle.cc>

From: Vladimir Oltean <vladimir.oltean@nxp.com>

Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
---
 drivers/net/phy/atheros.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c
index c0c2b4db39..1da18eb5d4 100644
--- a/drivers/net/phy/atheros.c
+++ b/drivers/net/phy/atheros.c
@@ -17,6 +17,15 @@
 #define AR803x_DEBUG_REG_0		0x0
 #define AR803x_RGMII_RX_CLK_DLY		BIT(15)
 
+/* CLK_25M register is at MMD 7, address 0x8016 */
+#define AR803x_CLK_25M_SEL_REG		0x8016
+/* AR8035: Select frequency on CLK_25M pin through bits 4:3 */
+#define AR8035_CLK_25M_FREQ_25M		(0 | 0)
+#define AR8035_CLK_25M_FREQ_50M		(0 | BIT(3))
+#define AR8035_CLK_25M_FREQ_62M		(BIT(4) | 0)
+#define AR8035_CLK_25M_FREQ_125M	(BIT(4) | BIT(3))
+#define AR8035_CLK_25M_MASK		GENMASK(4, 3)
+
 static void ar803x_enable_rx_delay(struct phy_device *phydev, bool on)
 {
 	int regval;
@@ -78,11 +87,11 @@ static int ar8035_config(struct phy_device *phydev)
 {
 	int regval;
 
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x0007);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-	regval = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, (regval|0x0018));
+	/* Configure CLK_25M output clock at 125 MHz */
+	regval = phy_read_mmd(phydev, MDIO_MMD_AN, AR803x_CLK_25M_SEL_REG);
+	regval &= ~AR8035_CLK_25M_MASK; /* No surprises */
+	regval |= AR8035_CLK_25M_FREQ_125M;
+	phy_write_mmd(phydev, MDIO_MMD_AN, AR803x_CLK_25M_SEL_REG, regval);
 
 	if ((phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
 	    (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID))
-- 
2.20.1

  parent reply	other threads:[~2020-05-06 22:11 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-05-06 22:11 [PATCH v4 00/12] phy: atheros: dt bindings and cleanup Michael Walle
2020-05-06 22:11 ` [PATCH v4 01/12] phy: atheros: Make RGMII Tx delays actually configurable for AR8035 Michael Walle
2020-05-07 18:51   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 02/12] phy: atheros: Use common functions for RGMII internal delays Michael Walle
2020-05-07 18:52   ` Tom Rini
2020-05-06 22:11 ` Michael Walle [this message]
2020-05-07 18:52   ` [PATCH v4 03/12] phy: atheros: Clarify the configuration of the CLK_25M output pin Tom Rini
2020-05-06 22:11 ` [PATCH v4 04/12] phy: atheros: Explicitly disable RGMII delays Michael Walle
2020-05-07 18:52   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 05/12] phy: atheros: Clarify the intention of ar8021_config Michael Walle
2020-05-07 18:52   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 06/12] phy: atheros: fix AR8021 PHY ID mask Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 07/12] phy: atheros: use defines for PHY IDs Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 08/12] phy: atheros: introduce debug read and write functions Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 09/12] phy: atheros: move delay config to common function Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 10/12] phy: atheros: add device tree bindings and config Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 11/12] phy: atheros: ar8035: remove static clock config Michael Walle
2020-05-07 18:53   ` Tom Rini
2020-05-06 22:11 ` [PATCH v4 12/12] phy: atheros: consolidate {ar8031|ar8035}_config() Michael Walle
2020-05-07 18:53   ` Tom Rini

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200506221159.1298-4-michael@walle.cc \
    --to=michael@walle.cc \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.