[PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[Wolfram Sang]

The SDHI driver en-/disabled clocks on its own during probe() and
remove(). This basically killed all potential RPM power savings. Now, we
just enable the clocks for a short time when we access registers in
probe(). We otherwise leave all handling to RPM. That means, we need to
shift the RPM enabling code in the TMIO core a bit up, so we can access
registers there, too.

clk_summary before:
sd0                   1        1        0    12480000          0     0  50000
   sdif0              2        2        0    12480000          0     0  50000

clk_summary after:
sd0                   1        1        0    12480000          0     0  50000
   sdif0              1        1        0    12480000          0     0  50000

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---

Tested on a Salvator-XS board with R-Car M3-N.

 drivers/mmc/host/renesas_sdhi_core.c |  7 +++----
 drivers/mmc/host/tmio_mmc_core.c     | 14 +++++++-------
 2 files changed, 10 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/renesas_sdhi_core.c b/drivers/mmc/host/renesas_sdhi_core.c
index ff72b381a6b3..d581142634f8 100644
--- a/drivers/mmc/host/renesas_sdhi_core.c
+++ b/drivers/mmc/host/renesas_sdhi_core.c
@@ -910,6 +910,8 @@ int renesas_sdhi_probe(struct platform_device *pdev,
 		goto efree;
 
 	ver = sd_ctrl_read16(host, CTL_VERSION);
+	renesas_sdhi_clk_disable(host);
+
 	/* GEN2_SDR104 is first known SDHI to use 32bit block count */
 	if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX)
 		mmc_data->max_blk_count = U16_MAX;
@@ -920,7 +922,7 @@ int renesas_sdhi_probe(struct platform_device *pdev,
 
 	ret = tmio_mmc_host_probe(host);
 	if (ret < 0)
-		goto edisclk;
+		goto efree;
 
 	/* Enable tuning iff we have an SCC and a supported mode */
 	if (of_data && of_data->scc_offset &&
@@ -985,8 +987,6 @@ int renesas_sdhi_probe(struct platform_device *pdev,
 
 eirq:
 	tmio_mmc_host_remove(host);
-edisclk:
-	renesas_sdhi_clk_disable(host);
 efree:
 	tmio_mmc_host_free(host);
 
@@ -999,7 +999,6 @@ int renesas_sdhi_remove(struct platform_device *pdev)
 	struct tmio_mmc_host *host = platform_get_drvdata(pdev);
 
 	tmio_mmc_host_remove(host);
-	renesas_sdhi_clk_disable(host);
 
 	return 0;
 }
diff --git a/drivers/mmc/host/tmio_mmc_core.c b/drivers/mmc/host/tmio_mmc_core.c
index 9a4ae954553b..6968177dd1cd 100644
--- a/drivers/mmc/host/tmio_mmc_core.c
+++ b/drivers/mmc/host/tmio_mmc_core.c
@@ -1116,6 +1116,13 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
 
 	_host->set_pwr = pdata->set_pwr;
 
+	dev_pm_domain_start(&pdev->dev);
+	pm_runtime_get_noresume(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	ret = tmio_mmc_init_ocr(_host);
 	if (ret < 0)
 		return ret;
@@ -1192,13 +1199,6 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
 	/* See if we also get DMA */
 	tmio_mmc_request_dma(_host, pdata);
 
-	dev_pm_domain_start(&pdev->dev);
-	pm_runtime_get_noresume(&pdev->dev);
-	pm_runtime_set_active(&pdev->dev);
-	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
-	pm_runtime_use_autosuspend(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
-
 	ret = mmc_add_host(mmc);
 	if (ret)
 		goto remove_host;
-- 
2.20.1

Re: [PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[Ulf Hansson]

+ Niklas, Geert, Yamada-san,


On Wed, 13 May 2020 at 19:31, Wolfram Sang
<wsa+renesas@sang-engineering.com> wrote:
>
> The SDHI driver en-/disabled clocks on its own during probe() and
> remove(). This basically killed all potential RPM power savings. Now, we
> just enable the clocks for a short time when we access registers in
> probe(). We otherwise leave all handling to RPM. That means, we need to
> shift the RPM enabling code in the TMIO core a bit up, so we can access
> registers there, too.

No, this doesn't sound entirely right to me.

However, I do admit that we may need to move the pm_runtime
initialization earlier (perhaps even out of tmio_mmc_core), but for
slightly different reasons. Let me elaborate.

For uniphier-sd, renesas_sdhi_sys_dmac and renesas_sdhi_internal_dmac
- they all have assigned the ->clk_enable|disable() ops. Which means
they have internal clock management (calling clk_prepare|enable()
etc). For tmio_mmc, that's not the case.

On top of this, the device may also have a potential PM domain
attached. If that is the case, the PM domain may or may not have clock
management implemented through genpd's ->start|stop() callbacks.

So, in the end we are going to have to rely on clock enable/prepare
reference counting, as we have to manage the clock(s) at both the
driver and the PM domain level. Taking into account all various
combinations (and that CONFIG_PM may not always be set). I have
started to hack on some patches, but before I share them, let me ask a
few questions.

1. tmio_mmc: - is that used solely with clock management through
genpd? Or has no clock management at all?
2. uniphier-sd: Don't have runtime PM callbacks assigned. It looks
like it doesn't care about runtime PM, but maybe it does through a PM
domain? Can we skip to enable runtime PM for uniphier-sd, no?

Kind regards
Uffe

>
> clk_summary before:
> sd0                   1        1        0    12480000          0     0  50000
>    sdif0              2        2        0    12480000          0     0  50000
>
> clk_summary after:
> sd0                   1        1        0    12480000          0     0  50000
>    sdif0              1        1        0    12480000          0     0  50000
>
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> ---
>
> Tested on a Salvator-XS board with R-Car M3-N.
>
>  drivers/mmc/host/renesas_sdhi_core.c |  7 +++----
>  drivers/mmc/host/tmio_mmc_core.c     | 14 +++++++-------
>  2 files changed, 10 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/mmc/host/renesas_sdhi_core.c b/drivers/mmc/host/renesas_sdhi_core.c
> index ff72b381a6b3..d581142634f8 100644
> --- a/drivers/mmc/host/renesas_sdhi_core.c
> +++ b/drivers/mmc/host/renesas_sdhi_core.c
> @@ -910,6 +910,8 @@ int renesas_sdhi_probe(struct platform_device *pdev,
>                 goto efree;
>
>         ver = sd_ctrl_read16(host, CTL_VERSION);
> +       renesas_sdhi_clk_disable(host);
> +
>         /* GEN2_SDR104 is first known SDHI to use 32bit block count */
>         if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX)
>                 mmc_data->max_blk_count = U16_MAX;
> @@ -920,7 +922,7 @@ int renesas_sdhi_probe(struct platform_device *pdev,
>
>         ret = tmio_mmc_host_probe(host);
>         if (ret < 0)
> -               goto edisclk;
> +               goto efree;
>
>         /* Enable tuning iff we have an SCC and a supported mode */
>         if (of_data && of_data->scc_offset &&
> @@ -985,8 +987,6 @@ int renesas_sdhi_probe(struct platform_device *pdev,
>
>  eirq:
>         tmio_mmc_host_remove(host);
> -edisclk:
> -       renesas_sdhi_clk_disable(host);
>  efree:
>         tmio_mmc_host_free(host);
>
> @@ -999,7 +999,6 @@ int renesas_sdhi_remove(struct platform_device *pdev)
>         struct tmio_mmc_host *host = platform_get_drvdata(pdev);
>
>         tmio_mmc_host_remove(host);
> -       renesas_sdhi_clk_disable(host);
>
>         return 0;
>  }
> diff --git a/drivers/mmc/host/tmio_mmc_core.c b/drivers/mmc/host/tmio_mmc_core.c
> index 9a4ae954553b..6968177dd1cd 100644
> --- a/drivers/mmc/host/tmio_mmc_core.c
> +++ b/drivers/mmc/host/tmio_mmc_core.c
> @@ -1116,6 +1116,13 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
>
>         _host->set_pwr = pdata->set_pwr;
>
> +       dev_pm_domain_start(&pdev->dev);
> +       pm_runtime_get_noresume(&pdev->dev);
> +       pm_runtime_set_active(&pdev->dev);
> +       pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
> +       pm_runtime_use_autosuspend(&pdev->dev);
> +       pm_runtime_enable(&pdev->dev);
> +
>         ret = tmio_mmc_init_ocr(_host);
>         if (ret < 0)
>                 return ret;
> @@ -1192,13 +1199,6 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
>         /* See if we also get DMA */
>         tmio_mmc_request_dma(_host, pdata);
>
> -       dev_pm_domain_start(&pdev->dev);
> -       pm_runtime_get_noresume(&pdev->dev);
> -       pm_runtime_set_active(&pdev->dev);
> -       pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
> -       pm_runtime_use_autosuspend(&pdev->dev);
> -       pm_runtime_enable(&pdev->dev);
> -
>         ret = mmc_add_host(mmc);
>         if (ret)
>                 goto remove_host;
> --
> 2.20.1
>

Re: [PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[Niklas Söderlund]

Hi Wolfram and Ulf,

Thanks for working on this!

On 2020-05-15 11:26:06 +0200, Ulf Hansson wrote:
> + Niklas, Geert, Yamada-san,
> 
> 
> On Wed, 13 May 2020 at 19:31, Wolfram Sang
> <wsa+renesas@sang-engineering.com> wrote:
> >
> > The SDHI driver en-/disabled clocks on its own during probe() and
> > remove(). This basically killed all potential RPM power savings. Now, we
> > just enable the clocks for a short time when we access registers in
> > probe(). We otherwise leave all handling to RPM. That means, we need to
> > shift the RPM enabling code in the TMIO core a bit up, so we can access
> > registers there, too.
> 
> No, this doesn't sound entirely right to me.
> 
> However, I do admit that we may need to move the pm_runtime
> initialization earlier (perhaps even out of tmio_mmc_core), but for
> slightly different reasons. Let me elaborate.
> 
> For uniphier-sd, renesas_sdhi_sys_dmac and renesas_sdhi_internal_dmac
> - they all have assigned the ->clk_enable|disable() ops. Which means
> they have internal clock management (calling clk_prepare|enable()
> etc). For tmio_mmc, that's not the case.
> 
> On top of this, the device may also have a potential PM domain
> attached. If that is the case, the PM domain may or may not have clock
> management implemented through genpd's ->start|stop() callbacks.
> 
> So, in the end we are going to have to rely on clock enable/prepare
> reference counting, as we have to manage the clock(s) at both the
> driver and the PM domain level. Taking into account all various
> combinations (and that CONFIG_PM may not always be set). I have
> started to hack on some patches, but before I share them, let me ask a
> few questions.

I had a go at this once but gave up as I only have knowledge about one 
implementation and !CONFIG_PM made it messy for me. I will see if I can 
digout the patches and see if I can recall exactly what it was. I'm sure 
it was my lack of understanding and not something technical.

> 
> 1. tmio_mmc: - is that used solely with clock management through
> genpd? Or has no clock management at all?
> 2. uniphier-sd: Don't have runtime PM callbacks assigned. It looks
> like it doesn't care about runtime PM, but maybe it does through a PM
> domain? Can we skip to enable runtime PM for uniphier-sd, no?
> 
> Kind regards
> Uffe
> 
> >
> > clk_summary before:
> > sd0                   1        1        0    12480000          0     0  50000
> >    sdif0              2        2        0    12480000          0     0  50000
> >
> > clk_summary after:
> > sd0                   1        1        0    12480000          0     0  50000
> >    sdif0              1        1        0    12480000          0     0  50000
> >
> > Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> > ---
> >
> > Tested on a Salvator-XS board with R-Car M3-N.
> >
> >  drivers/mmc/host/renesas_sdhi_core.c |  7 +++----
> >  drivers/mmc/host/tmio_mmc_core.c     | 14 +++++++-------
> >  2 files changed, 10 insertions(+), 11 deletions(-)
> >
> > diff --git a/drivers/mmc/host/renesas_sdhi_core.c b/drivers/mmc/host/renesas_sdhi_core.c
> > index ff72b381a6b3..d581142634f8 100644
> > --- a/drivers/mmc/host/renesas_sdhi_core.c
> > +++ b/drivers/mmc/host/renesas_sdhi_core.c
> > @@ -910,6 +910,8 @@ int renesas_sdhi_probe(struct platform_device *pdev,
> >                 goto efree;
> >
> >         ver = sd_ctrl_read16(host, CTL_VERSION);
> > +       renesas_sdhi_clk_disable(host);
> > +
> >         /* GEN2_SDR104 is first known SDHI to use 32bit block count */
> >         if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX)
> >                 mmc_data->max_blk_count = U16_MAX;
> > @@ -920,7 +922,7 @@ int renesas_sdhi_probe(struct platform_device *pdev,
> >
> >         ret = tmio_mmc_host_probe(host);
> >         if (ret < 0)
> > -               goto edisclk;
> > +               goto efree;
> >
> >         /* Enable tuning iff we have an SCC and a supported mode */
> >         if (of_data && of_data->scc_offset &&
> > @@ -985,8 +987,6 @@ int renesas_sdhi_probe(struct platform_device *pdev,
> >
> >  eirq:
> >         tmio_mmc_host_remove(host);
> > -edisclk:
> > -       renesas_sdhi_clk_disable(host);
> >  efree:
> >         tmio_mmc_host_free(host);
> >
> > @@ -999,7 +999,6 @@ int renesas_sdhi_remove(struct platform_device *pdev)
> >         struct tmio_mmc_host *host = platform_get_drvdata(pdev);
> >
> >         tmio_mmc_host_remove(host);
> > -       renesas_sdhi_clk_disable(host);
> >
> >         return 0;
> >  }
> > diff --git a/drivers/mmc/host/tmio_mmc_core.c b/drivers/mmc/host/tmio_mmc_core.c
> > index 9a4ae954553b..6968177dd1cd 100644
> > --- a/drivers/mmc/host/tmio_mmc_core.c
> > +++ b/drivers/mmc/host/tmio_mmc_core.c
> > @@ -1116,6 +1116,13 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
> >
> >         _host->set_pwr = pdata->set_pwr;
> >
> > +       dev_pm_domain_start(&pdev->dev);
> > +       pm_runtime_get_noresume(&pdev->dev);
> > +       pm_runtime_set_active(&pdev->dev);
> > +       pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
> > +       pm_runtime_use_autosuspend(&pdev->dev);
> > +       pm_runtime_enable(&pdev->dev);
> > +
> >         ret = tmio_mmc_init_ocr(_host);
> >         if (ret < 0)
> >                 return ret;
> > @@ -1192,13 +1199,6 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host)
> >         /* See if we also get DMA */
> >         tmio_mmc_request_dma(_host, pdata);
> >
> > -       dev_pm_domain_start(&pdev->dev);
> > -       pm_runtime_get_noresume(&pdev->dev);
> > -       pm_runtime_set_active(&pdev->dev);
> > -       pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
> > -       pm_runtime_use_autosuspend(&pdev->dev);
> > -       pm_runtime_enable(&pdev->dev);
> > -
> >         ret = mmc_add_host(mmc);
> >         if (ret)
> >                 goto remove_host;
> > --
> > 2.20.1
> >

-- 
Regards,
Niklas Söderlund

Re: [PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[Masahiro Yamada]

On Fri, May 15, 2020 at 6:26 PM Ulf Hansson <ulf.hansson@linaro.org> wrote:
>
> + Niklas, Geert, Yamada-san,
>
>
> On Wed, 13 May 2020 at 19:31, Wolfram Sang
> <wsa+renesas@sang-engineering.com> wrote:
> >
> > The SDHI driver en-/disabled clocks on its own during probe() and
> > remove(). This basically killed all potential RPM power savings. Now, we
> > just enable the clocks for a short time when we access registers in
> > probe(). We otherwise leave all handling to RPM. That means, we need to
> > shift the RPM enabling code in the TMIO core a bit up, so we can access
> > registers there, too.
>
> No, this doesn't sound entirely right to me.
>
> However, I do admit that we may need to move the pm_runtime
> initialization earlier (perhaps even out of tmio_mmc_core), but for
> slightly different reasons. Let me elaborate.
>
> For uniphier-sd, renesas_sdhi_sys_dmac and renesas_sdhi_internal_dmac
> - they all have assigned the ->clk_enable|disable() ops. Which means
> they have internal clock management (calling clk_prepare|enable()
> etc). For tmio_mmc, that's not the case.
>
> On top of this, the device may also have a potential PM domain
> attached. If that is the case, the PM domain may or may not have clock
> management implemented through genpd's ->start|stop() callbacks.
>
> So, in the end we are going to have to rely on clock enable/prepare
> reference counting, as we have to manage the clock(s) at both the
> driver and the PM domain level. Taking into account all various
> combinations (and that CONFIG_PM may not always be set). I have
> started to hack on some patches, but before I share them, let me ask a
> few questions.
>
> 1. tmio_mmc: - is that used solely with clock management through
> genpd? Or has no clock management at all?
> 2. uniphier-sd: Don't have runtime PM callbacks assigned. It looks
> like it doesn't care about runtime PM, but maybe it does through a PM
> domain? Can we skip to enable runtime PM for uniphier-sd, no?


Right, uniphier-sd does not care about runtime PM.
UniPhier SoCs do not have separate power domains.



-- 
Best Regards
Masahiro Yamada

Re: [PATCH] mmc: renesas_sdhi: don't lose RPM savings because of manual clk handling

[Geert Uytterhoeven]

Hi Wolfram,

On Wed, May 13, 2020 at 7:31 PM Wolfram Sang
<wsa+renesas@sang-engineering.com> wrote:
> The SDHI driver en-/disabled clocks on its own during probe() and
> remove(). This basically killed all potential RPM power savings. Now, we
> just enable the clocks for a short time when we access registers in
> probe(). We otherwise leave all handling to RPM. That means, we need to
> shift the RPM enabling code in the TMIO core a bit up, so we can access
> registers there, too.
>
> clk_summary before:
> sd0                   1        1        0    12480000          0     0  50000
>    sdif0              2        2        0    12480000          0     0  50000
>
> clk_summary after:
> sd0                   1        1        0    12480000          0     0  50000
>    sdif0              1        1        0    12480000          0     0  50000
>
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> ---
>
> Tested on a Salvator-XS board with R-Car M3-N.

While this seems to have no ill effects on R-Car Gen3, RZ/A1, and RZ/A2,
it does on R-Car Gen2, which prints before probing:

    sh_mobile_sdhi ee100000.sd: Unbalanced pm_runtime_enable!

And on SH-Mobile AG5, R-Mobile A1, and R-Mobile APE6:

    ------------[ cut here ]------------
    WARNING: CPU: 0 PID: 5 at drivers/clk/clk.c:954 clk_core_disable+0x6c/0x2b0
    sdhi1 already disabled
    CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
5.7.0-rc5-ape6evm-00536-ga65e619d428aff9a-dirty #186
    Hardware name: Generic R8A73A4 (Flattened Device Tree)
    Workqueue: pm pm_runtime_work
    [<c00169e8>] (unwind_backtrace) from [<c001345c>] (show_stack+0x10/0x14)
    [<c001345c>] (show_stack) from [<c04b6e34>] (dump_stack+0x88/0xa8)
    [<c04b6e34>] (dump_stack) from [<c00270b8>] (__warn+0xd0/0xec)
    [<c00270b8>] (__warn) from [<c0027144>] (warn_slowpath_fmt+0x70/0x9c)
    [<c0027144>] (warn_slowpath_fmt) from [<c029d53c>]
(clk_core_disable+0x6c/0x2b0)
    [<c029d53c>] (clk_core_disable) from [<c029d798>]
(clk_core_disable_lock+0x18/0x24)
    [<c029d798>] (clk_core_disable_lock) from [<c02fa670>]
(pm_clk_suspend+0x64/0x78)
    [<c02fa670>] (pm_clk_suspend) from [<c02f8918>]
(genpd_runtime_suspend+0x110/0x1bc)
    [<c02f8918>] (genpd_runtime_suspend) from [<c02f01b4>]
(__rpm_callback+0x30/0xe0)
    [<c02f01b4>] (__rpm_callback) from [<c02f02d4>] (rpm_callback+0x70/0x80)
    [<c02f02d4>] (rpm_callback) from [<c02f0e28>] (rpm_suspend+0x330/0x4a0)
    [<c02f0e28>] (rpm_suspend) from [<c02f1240>] (pm_runtime_work+0x74/0x8c)
    [<c02f1240>] (pm_runtime_work) from [<c00402f4>]
(process_one_work+0x2cc/0x4ac)
    [<c00402f4>] (process_one_work) from [<c0040730>]
(worker_thread+0x230/0x2f0)
    [<c0040730>] (worker_thread) from [<c0045b9c>] (kthread+0x12c/0x13c)
    [<c0045b9c>] (kthread) from [<c0009148>] (ret_from_fork+0x14/0x2c)
    Exception stack(0xef0cdfb0 to 0xef0cdff8)
    dfa0:                                     00000000 00000000
00000000 00000000
    dfc0: 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
    dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
    ---[ end trace c1cca51c99a6297a ]---

and later:

    ------------[ cut here ]------------
    WARNING: CPU: 0 PID: 12 at drivers/clk/clk.c:1014 clk_core_enable+0x6c/0x2bc
    Enabling unprepared sdhi1
    CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: G        W
5.7.0-rc5-ape6evm-00536-ga65e619d428aff9a-dirty #186
    Hardware name: Generic R8A73A4 (Flattened Device Tree)
    Workqueue: events_freezable mmc_rescan
    [<c00169e8>] (unwind_backtrace) from [<c001345c>] (show_stack+0x10/0x14)
    [<c001345c>] (show_stack) from [<c04b6e34>] (dump_stack+0x88/0xa8)
    [<c04b6e34>] (dump_stack) from [<c00270b8>] (__warn+0xd0/0xec)
    [<c00270b8>] (__warn) from [<c0027144>] (warn_slowpath_fmt+0x70/0x9c)
    [<c0027144>] (warn_slowpath_fmt) from [<c029d810>]
(clk_core_enable+0x6c/0x2bc)
    [<c029d810>] (clk_core_enable) from [<c029da78>]
(clk_core_enable_lock+0x18/0x2c)
    [<c029da78>] (clk_core_enable_lock) from [<c02fa6ec>]
(pm_clk_resume+0x68/0xa0)
    [<c02fa6ec>] (pm_clk_resume) from [<c02f8dd0>]
(genpd_runtime_resume+0xc8/0x170)
    [<c02f8dd0>] (genpd_runtime_resume) from [<c02f01b4>]
(__rpm_callback+0x30/0xe0)
    [<c02f01b4>] (__rpm_callback) from [<c02f02d4>] (rpm_callback+0x70/0x80)
    [<c02f02d4>] (rpm_callback) from [<c02f0a50>] (rpm_resume+0x44c/0x4f4)
    [<c02f0a50>] (rpm_resume) from [<c02f00f0>] (__pm_runtime_resume+0x64/0x80)
    [<c02f00f0>] (__pm_runtime_resume) from [<c0342480>]
(__mmc_claim_host+0x1c8/0x218)
    [<c0342480>] (__mmc_claim_host) from [<c03437f0>] (mmc_rescan+0xfc/0x260)
    [<c03437f0>] (mmc_rescan) from [<c00402f4>] (process_one_work+0x2cc/0x4ac)
    [<c00402f4>] (process_one_work) from [<c0040730>]
(worker_thread+0x230/0x2f0)
    [<c0040730>] (worker_thread) from [<c0045b9c>] (kthread+0x12c/0x13c)
    [<c0045b9c>] (kthread) from [<c0009148>] (ret_from_fork+0x14/0x2c)
    Exception stack(0xef0f1fb0 to 0xef0f1ff8)
    1fa0:                                     00000000 00000000
00000000 00000000
    1fc0: 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
    1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
    ---[ end trace c1cca51c99a6297b ]---
    sh_mobile_sdhi ee120000.sd: __pm_clk_enable: failed to enable clk
(ptrval), error -108

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds