[PATCH net-next 0/2] am65-cpsw: add taprio/EST offload support

[PATCH net-next 0/2] am65-cpsw: add taprio/EST offload support

[Murali Karicheri]

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() as well as other changes required to offload EST
configuration to CPSW h/w

For more details please refer patch 2/2.

This series is based on original work done by Ivan Khoronzhuk
<ivan.khoronzhuk@linaro.org> to add taprio offload support to
AM65 CPSW 2G. 

1. Example configuration 3 Gates

ifconfig eth0 down
ethtool -L eth0 tx 3

#disable rrobin
ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

ifconfig eth0 192.168.2.20

tc qdisc replace dev eth0 parent root handle 100 taprio \
    num_tc 3 \
    map 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 \
    queues 1@0 1@1 1@2 \
    base-time 0000 \
    sched-entry S 4 125000 \
    sched-entry S 2 125000 \
    sched-entry S 1 250000 \
    flags 2

2. Example configuration 8 Gates 

ifconfig eth0 down
ethtool -L eth0 tx 8

#disable rrobin
ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

ifconfig eth0 192.168.2.20

tc qdisc replace dev eth0 parent root handle 100 taprio \
    num_tc 8 \
    map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
    queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
    base-time 0000 \
    sched-entry S 80 125000 \
    sched-entry S 40 125000 \
    sched-entry S 20 125000 \
    sched-entry S 10 125000 \
    sched-entry S 08 125000 \
    sched-entry S 04 125000 \
    sched-entry S 02 125000 \
    sched-entry S 01 125000 \
    flags 2


Classify frames to particular priority using skbedit so that they land at
a specific queue in cpsw h/w which is Gated by the EST gate which opens based
on the sched-entry. 

tc qdisc add dev eth0 clsact

In the below for example an iperf3 session with destination port 5007
will go through Q7.

# Assume case 1: 8 TCs as per the second tc command listed above
# Assign packet prio 7 for port 5007 -> hw_prio 7
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5007 0xffff action skbedit priority 7

# Similarly, assign packet prio 6 for port 5006 -> hw_prio 6 and so forth
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5006 0xffff action skbedit priority 6
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5005 0xffff action skbedit priority 5
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5004 0xffff action skbedit priority 4
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5003 0xffff action skbedit priority 3
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5002 0xffff action skbedit priority 2
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5001 0xffff action skbedit priority 1

#send iperf3 udp traffic for port 5007 with iperf3 server running at
#a PC connected to the eth0 port

iperf3 -c 192.168.2.10 -u -l1470 -b32M -t1 -p 5007

Testing was done by capturing frames at the PC using wireshark and checking for
the bust interval or cycle time of UDP frames with a specific port number. 
Verified that the distance between first frame of a burst (cycle-time) is 1
milli second and burst duration is within 125 usec based on the received packet
timestamp shown in wireshark packet display. 

Ivan Khoronzhuk (2):
  ethernet: ti: am65-cpts: add routines to support taprio offload
  ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

 drivers/net/ethernet/ti/Kconfig             |   9 +
 drivers/net/ethernet/ti/Makefile            |   2 +-
 drivers/net/ethernet/ti/am65-cpsw-ethtool.c |  12 +-
 drivers/net/ethernet/ti/am65-cpsw-nuss.c    |   9 +
 drivers/net/ethernet/ti/am65-cpsw-nuss.h    |   5 +
 drivers/net/ethernet/ti/am65-cpsw-qos.c     | 626 ++++++++++++++++++++
 drivers/net/ethernet/ti/am65-cpsw-qos.h     |  29 +
 drivers/net/ethernet/ti/am65-cpts.c         |  48 ++
 drivers/net/ethernet/ti/am65-cpts.h         |  24 +
 9 files changed, 761 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-qos.c
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-qos.h

-- 
2.17.1

[PATCH net-next 1/2] ethernet: ti: am65-cpts: add routines to support taprio offload

[Murali Karicheri]

From: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>

TAPRIO/EST offload support in CPSW2G requires EST scheduler
function enabled in CPTS. So this patch add a function to
set cycle time for EST scheduler.  It also add a function for
getting time in ns of PHC clock for taprio qdisc configuration.
Mostly to verify if timer update is needed or to get actual
state of oper/admin schedule.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 drivers/net/ethernet/ti/am65-cpts.c | 48 +++++++++++++++++++++++++++++
 drivers/net/ethernet/ti/am65-cpts.h | 24 +++++++++++++++
 2 files changed, 72 insertions(+)

diff --git a/drivers/net/ethernet/ti/am65-cpts.c b/drivers/net/ethernet/ti/am65-cpts.c
index 51c94b2a77b1..c59a289e428c 100644
--- a/drivers/net/ethernet/ti/am65-cpts.c
+++ b/drivers/net/ethernet/ti/am65-cpts.c
@@ -450,6 +450,19 @@ static int am65_cpts_ptp_gettimex(struct ptp_clock_info *ptp,
 	return 0;
 }
 
+u64 am65_cpts_ns_gettime(struct am65_cpts *cpts)
+{
+	u64 ns;
+
+	/* reuse ptp_clk_lock as it serialize ts push */
+	mutex_lock(&cpts->ptp_clk_lock);
+	ns = am65_cpts_gettime(cpts, NULL);
+	mutex_unlock(&cpts->ptp_clk_lock);
+
+	return ns;
+}
+EXPORT_SYMBOL_GPL(am65_cpts_ns_gettime);
+
 static int am65_cpts_ptp_settime(struct ptp_clock_info *ptp,
 				 const struct timespec64 *ts)
 {
@@ -494,6 +507,41 @@ static int am65_cpts_extts_enable(struct am65_cpts *cpts, u32 index, int on)
 	return 0;
 }
 
+int am65_cpts_estf_enable(struct am65_cpts *cpts, int idx,
+			  struct am65_cpts_estf_cfg *cfg)
+{
+	u64 cycles;
+	u32 val;
+
+	cycles = cfg->ns_period * cpts->refclk_freq;
+	cycles = DIV_ROUND_UP(cycles, NSEC_PER_SEC);
+	if (cycles > U32_MAX)
+		return -EINVAL;
+
+	/* according to TRM should be zeroed */
+	am65_cpts_write32(cpts, 0, estf[idx].length);
+
+	val = upper_32_bits(cfg->ns_start);
+	am65_cpts_write32(cpts, val, estf[idx].comp_hi);
+	val = lower_32_bits(cfg->ns_start);
+	am65_cpts_write32(cpts, val, estf[idx].comp_lo);
+	val = lower_32_bits(cycles);
+	am65_cpts_write32(cpts, val, estf[idx].length);
+
+	dev_dbg(cpts->dev, "%s: ESTF:%u enabled\n", __func__, idx);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(am65_cpts_estf_enable);
+
+void am65_cpts_estf_disable(struct am65_cpts *cpts, int idx)
+{
+	am65_cpts_write32(cpts, 0, estf[idx].length);
+
+	dev_dbg(cpts->dev, "%s: ESTF:%u disabled\n", __func__, idx);
+}
+EXPORT_SYMBOL_GPL(am65_cpts_estf_disable);
+
 static void am65_cpts_perout_enable_hw(struct am65_cpts *cpts,
 				       struct ptp_perout_request *req, int on)
 {
diff --git a/drivers/net/ethernet/ti/am65-cpts.h b/drivers/net/ethernet/ti/am65-cpts.h
index 0b55dc12ba48..98c1960b20b9 100644
--- a/drivers/net/ethernet/ti/am65-cpts.h
+++ b/drivers/net/ethernet/ti/am65-cpts.h
@@ -12,6 +12,11 @@
 
 struct am65_cpts;
 
+struct am65_cpts_estf_cfg {
+	u64 ns_period;
+	u64 ns_start;
+};
+
 #if IS_ENABLED(CONFIG_TI_K3_AM65_CPTS)
 struct am65_cpts *am65_cpts_create(struct device *dev, void __iomem *regs,
 				   struct device_node *node);
@@ -19,6 +24,10 @@ int am65_cpts_phc_index(struct am65_cpts *cpts);
 void am65_cpts_tx_timestamp(struct am65_cpts *cpts, struct sk_buff *skb);
 void am65_cpts_prep_tx_timestamp(struct am65_cpts *cpts, struct sk_buff *skb);
 void am65_cpts_rx_enable(struct am65_cpts *cpts, bool en);
+u64 am65_cpts_ns_gettime(struct am65_cpts *cpts);
+int am65_cpts_estf_enable(struct am65_cpts *cpts, int idx,
+			  struct am65_cpts_estf_cfg *cfg);
+void am65_cpts_estf_disable(struct am65_cpts *cpts, int idx);
 #else
 static inline struct am65_cpts *am65_cpts_create(struct device *dev,
 						 void __iomem *regs,
@@ -45,6 +54,21 @@ static inline void am65_cpts_prep_tx_timestamp(struct am65_cpts *cpts,
 static inline void am65_cpts_rx_enable(struct am65_cpts *cpts, bool en)
 {
 }
+
+static s64 am65_cpts_ns_gettime(struct am65_cpts *cpts)
+{
+	return 0;
+}
+
+static int am65_cpts_estf_enable(struct am65_cpts *cpts,
+				 int idx, struct am65_cpts_estf_cfg *cfg)
+{
+	return 0;
+}
+
+static void am65_cpts_estf_disable(struct am65_cpts *cpts, int idx)
+{
+}
 #endif
 
 #endif /* K3_CPTS_H_ */
-- 
2.17.1

[PATCH net-next 2/2] ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

[Murali Karicheri]

From: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.

Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.

CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.

Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM  depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.

The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 drivers/net/ethernet/ti/Kconfig             |   9 +
 drivers/net/ethernet/ti/Makefile            |   2 +-
 drivers/net/ethernet/ti/am65-cpsw-ethtool.c |  12 +-
 drivers/net/ethernet/ti/am65-cpsw-nuss.c    |   9 +
 drivers/net/ethernet/ti/am65-cpsw-nuss.h    |   5 +
 drivers/net/ethernet/ti/am65-cpsw-qos.c     | 626 ++++++++++++++++++++
 drivers/net/ethernet/ti/am65-cpsw-qos.h     |  29 +
 7 files changed, 689 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-qos.c
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-qos.h

diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 988e907e3322..4d4852f00ff7 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -123,6 +123,15 @@ config TI_K3_AM65_CPTS
 	  protocol, Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn)
 	  and PCIe Subsystem Precision Time Measurement (PTM).
 
+config TI_AM65_CPSW_TAS
+	bool "Enable TAS offload in AM65 CPSW"
+	depends on TI_K3_AM65_CPSW_NUSS && NET_SCH_TAPRIO && TI_K3_AM65_CPTS
+	help
+	  Say y here to support Time Aware Shaper(TAS) offload in AM65 CPSW.
+	  AM65 CPSW hardware supports Enhanced Scheduled Traffic (EST)
+	  defined in IEEE 802.1Q 2018. The EST scheduler runs on CPTS and the
+	  TAS/EST schedule is updated in the Fetch RAM memory of the CPSW.
+
 config TI_KEYSTONE_NETCP
 	tristate "TI Keystone NETCP Core Support"
 	select TI_DAVINCI_MDIO
diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
index bf86067f9b4c..be95512d80b5 100644
--- a/drivers/net/ethernet/ti/Makefile
+++ b/drivers/net/ethernet/ti/Makefile
@@ -25,5 +25,5 @@ obj-$(CONFIG_TI_KEYSTONE_NETCP_ETHSS) += keystone_netcp_ethss.o
 keystone_netcp_ethss-y := netcp_ethss.o netcp_sgmii.o netcp_xgbepcsr.o cpsw_ale.o
 
 obj-$(CONFIG_TI_K3_AM65_CPSW_NUSS) += ti-am65-cpsw-nuss.o
-ti-am65-cpsw-nuss-y := am65-cpsw-nuss.o cpsw_sl.o am65-cpsw-ethtool.o cpsw_ale.o k3-cppi-desc-pool.o
+ti-am65-cpsw-nuss-y := am65-cpsw-nuss.o cpsw_sl.o am65-cpsw-ethtool.o cpsw_ale.o k3-cppi-desc-pool.o am65-cpsw-qos.o
 obj-$(CONFIG_TI_K3_AM65_CPTS) += am65-cpts.o
diff --git a/drivers/net/ethernet/ti/am65-cpsw-ethtool.c b/drivers/net/ethernet/ti/am65-cpsw-ethtool.c
index 23661a6ed426..8c4690f3ebcb 100644
--- a/drivers/net/ethernet/ti/am65-cpsw-ethtool.c
+++ b/drivers/net/ethernet/ti/am65-cpsw-ethtool.c
@@ -730,9 +730,17 @@ static u32 am65_cpsw_get_ethtool_priv_flags(struct net_device *ndev)
 static int am65_cpsw_set_ethtool_priv_flags(struct net_device *ndev, u32 flags)
 {
 	struct am65_cpsw_common *common = am65_ndev_to_common(ndev);
+	int rrobin;
 
-	common->pf_p0_rx_ptype_rrobin =
-			!!(flags & AM65_CPSW_PRIV_P0_RX_PTYPE_RROBIN);
+	rrobin = !!(flags & AM65_CPSW_PRIV_P0_RX_PTYPE_RROBIN);
+
+	if (common->est_enabled && rrobin) {
+		netdev_err(ndev,
+			   "p0-rx-ptype-rrobin flag conflicts with QOS\n");
+		return -EINVAL;
+	}
+
+	common->pf_p0_rx_ptype_rrobin = rrobin;
 	am65_cpsw_nuss_set_p0_ptype(common);
 
 	return 0;
diff --git a/drivers/net/ethernet/ti/am65-cpsw-nuss.c b/drivers/net/ethernet/ti/am65-cpsw-nuss.c
index 8cdbb2b9b13a..4a8229864ae4 100644
--- a/drivers/net/ethernet/ti/am65-cpsw-nuss.c
+++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.c
@@ -37,12 +37,14 @@
 #define AM65_CPSW_XGMII_BASE	0x2100
 #define AM65_CPSW_CPSW_NU_BASE	0x20000
 #define AM65_CPSW_NU_PORTS_BASE	0x1000
+#define AM65_CPSW_NU_FRAM_BASE	0x12000
 #define AM65_CPSW_NU_STATS_BASE	0x1a000
 #define AM65_CPSW_NU_ALE_BASE	0x1e000
 #define AM65_CPSW_NU_CPTS_BASE	0x1d000
 
 #define AM65_CPSW_NU_PORTS_OFFSET	0x1000
 #define AM65_CPSW_NU_STATS_PORT_OFFSET	0x200
+#define AM65_CPSW_NU_FRAM_PORT_OFFSET	0x200
 
 #define AM65_CPSW_MAX_PORTS	8
 
@@ -188,9 +190,11 @@ void am65_cpsw_nuss_adjust_link(struct net_device *ndev)
 		cpsw_ale_control_set(common->ale, port->port_id,
 				     ALE_PORT_STATE, ALE_PORT_STATE_FORWARD);
 
+		am65_cpsw_qos_link_up(ndev, phy->speed);
 		netif_tx_wake_all_queues(ndev);
 	} else {
 		int tmo;
+
 		/* disable forwarding */
 		cpsw_ale_control_set(common->ale, port->port_id,
 				     ALE_PORT_STATE, ALE_PORT_STATE_DISABLE);
@@ -204,6 +208,7 @@ void am65_cpsw_nuss_adjust_link(struct net_device *ndev)
 
 		cpsw_sl_ctl_reset(port->slave.mac_sl);
 
+		am65_cpsw_qos_link_down(ndev);
 		netif_tx_stop_all_queues(ndev);
 	}
 
@@ -1378,6 +1383,7 @@ static const struct net_device_ops am65_cpsw_nuss_netdev_ops_2g = {
 	.ndo_vlan_rx_kill_vid	= am65_cpsw_nuss_ndo_slave_kill_vid,
 	.ndo_do_ioctl		= am65_cpsw_nuss_ndo_slave_ioctl,
 	.ndo_set_features	= am65_cpsw_nuss_ndo_slave_set_features,
+	.ndo_setup_tc           = am65_cpsw_qos_ndo_setup_tc,
 };
 
 static void am65_cpsw_nuss_slave_disable_unused(struct am65_cpsw_port *port)
@@ -1739,6 +1745,9 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common)
 		port->stat_base = common->cpsw_base + AM65_CPSW_NU_STATS_BASE +
 				  (AM65_CPSW_NU_STATS_PORT_OFFSET * port_id);
 		port->name = of_get_property(port_np, "label", NULL);
+		port->fetch_ram_base =
+				common->cpsw_base + AM65_CPSW_NU_FRAM_BASE +
+				(AM65_CPSW_NU_FRAM_PORT_OFFSET * (port_id - 1));
 
 		port->disabled = !of_device_is_available(port_np);
 		if (port->disabled)
diff --git a/drivers/net/ethernet/ti/am65-cpsw-nuss.h b/drivers/net/ethernet/ti/am65-cpsw-nuss.h
index 8a6382188cb5..9faf4fb1409b 100644
--- a/drivers/net/ethernet/ti/am65-cpsw-nuss.h
+++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.h
@@ -9,7 +9,9 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/netdevice.h>
+#include <linux/phy.h>
 #include <linux/platform_device.h>
+#include "am65-cpsw-qos.h"
 
 struct am65_cpts;
 
@@ -38,10 +40,12 @@ struct am65_cpsw_port {
 	u32				port_id;
 	void __iomem			*port_base;
 	void __iomem			*stat_base;
+	void __iomem			*fetch_ram_base;
 	bool				disabled;
 	struct am65_cpsw_slave_data	slave;
 	bool				tx_ts_enabled;
 	bool				rx_ts_enabled;
+	struct am65_cpsw_qos		qos;
 };
 
 struct am65_cpsw_host {
@@ -104,6 +108,7 @@ struct am65_cpsw_common {
 	u32			cpsw_ver;
 	bool			pf_p0_rx_ptype_rrobin;
 	struct am65_cpts	*cpts;
+	int			est_enabled;
 };
 
 struct am65_cpsw_ndev_stats {
diff --git a/drivers/net/ethernet/ti/am65-cpsw-qos.c b/drivers/net/ethernet/ti/am65-cpsw-qos.c
new file mode 100644
index 000000000000..32eac04468bb
--- /dev/null
+++ b/drivers/net/ethernet/ti/am65-cpsw-qos.c
@@ -0,0 +1,626 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments K3 AM65 Ethernet QoS submodule
+ * Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * quality of service module includes:
+ * Enhanced Scheduler Traffic (EST - P802.1Qbv/D2.2)
+ */
+
+#include <linux/pm_runtime.h>
+#include <linux/time.h>
+
+#include "am65-cpsw-nuss.h"
+#include "am65-cpsw-qos.h"
+#include "am65-cpts.h"
+
+#define AM65_CPSW_REG_CTL			0x004
+#define AM65_CPSW_PN_REG_CTL			0x004
+#define AM65_CPSW_PN_REG_FIFO_STATUS		0x050
+#define AM65_CPSW_PN_REG_EST_CTL		0x060
+
+/* AM65_CPSW_REG_CTL register fields */
+#define AM65_CPSW_CTL_EST_EN			BIT(18)
+
+/* AM65_CPSW_PN_REG_CTL register fields */
+#define AM65_CPSW_PN_CTL_EST_PORT_EN		BIT(17)
+
+/* AM65_CPSW_PN_REG_EST_CTL register fields */
+#define AM65_CPSW_PN_EST_ONEBUF			BIT(0)
+#define AM65_CPSW_PN_EST_BUFSEL			BIT(1)
+#define AM65_CPSW_PN_EST_TS_EN			BIT(2)
+#define AM65_CPSW_PN_EST_TS_FIRST		BIT(3)
+#define AM65_CPSW_PN_EST_ONEPRI			BIT(4)
+#define AM65_CPSW_PN_EST_TS_PRI_MSK		GENMASK(7, 5)
+
+/* AM65_CPSW_PN_REG_FIFO_STATUS register fields */
+#define AM65_CPSW_PN_FST_TX_PRI_ACTIVE_MSK	GENMASK(7, 0)
+#define AM65_CPSW_PN_FST_TX_E_MAC_ALLOW_MSK	GENMASK(15, 8)
+#define AM65_CPSW_PN_FST_EST_CNT_ERR		BIT(16)
+#define AM65_CPSW_PN_FST_EST_ADD_ERR		BIT(17)
+#define AM65_CPSW_PN_FST_EST_BUFACT		BIT(18)
+
+/* EST FETCH COMMAND RAM */
+#define AM65_CPSW_FETCH_RAM_CMD_NUM		0x80
+#define AM65_CPSW_FETCH_CNT_MSK			GENMASK(21, 8)
+#define AM65_CPSW_FETCH_CNT_MAX			(AM65_CPSW_FETCH_CNT_MSK >> 8)
+#define AM65_CPSW_FETCH_CNT_OFFSET		8
+#define AM65_CPSW_FETCH_ALLOW_MSK		GENMASK(7, 0)
+#define AM65_CPSW_FETCH_ALLOW_MAX		AM65_CPSW_FETCH_ALLOW_MSK
+
+enum timer_act {
+	TACT_PROG,		/* need program timer */
+	TACT_NEED_STOP,		/* need stop first */
+	TACT_SKIP_PROG,		/* just buffer can be updated */
+};
+
+static int am65_cpsw_port_est_enabled(struct am65_cpsw_port *port)
+{
+	return port->qos.est_oper || port->qos.est_admin;
+}
+
+static void am65_cpsw_est_enable(struct am65_cpsw_common *common, int enable)
+{
+	u32 val;
+
+	val = readl(common->cpsw_base + AM65_CPSW_REG_CTL);
+
+	if (enable)
+		val |= AM65_CPSW_CTL_EST_EN;
+	else
+		val &= ~AM65_CPSW_CTL_EST_EN;
+
+	writel(val, common->cpsw_base + AM65_CPSW_REG_CTL);
+	common->est_enabled = enable;
+}
+
+static void am65_cpsw_port_est_enable(struct am65_cpsw_port *port, int enable)
+{
+	u32 val;
+
+	val = readl(port->port_base + AM65_CPSW_PN_REG_CTL);
+	if (enable)
+		val |= AM65_CPSW_PN_CTL_EST_PORT_EN;
+	else
+		val &= ~AM65_CPSW_PN_CTL_EST_PORT_EN;
+
+	writel(val, port->port_base + AM65_CPSW_PN_REG_CTL);
+}
+
+/* target new EST RAM buffer, actual toggle happens after cycle completion */
+static void am65_cpsw_port_est_assign_buf_num(struct net_device *ndev,
+					      int buf_num)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	u32 val;
+
+	val = readl(port->port_base + AM65_CPSW_PN_REG_EST_CTL);
+	if (buf_num)
+		val |= AM65_CPSW_PN_EST_BUFSEL;
+	else
+		val &= ~AM65_CPSW_PN_EST_BUFSEL;
+
+	writel(val, port->port_base + AM65_CPSW_PN_REG_EST_CTL);
+}
+
+/* am65_cpsw_port_est_is_swapped() - Indicate if h/w is transitioned
+ * admin -> oper or not
+ *
+ * Return true if already transitioned. i.e oper is equal to admin and buf
+ * numbers match (est_oper->buf match with est_admin->buf).
+ * false if before transition. i.e oper is not equal to admin, (i.e a
+ * previous admin command is waiting to be transitioned to oper state
+ * and est_oper->buf not match with est_oper->buf).
+ */
+static int am65_cpsw_port_est_is_swapped(struct net_device *ndev, int *oper,
+					 int *admin)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	u32 val;
+
+	val = readl(port->port_base + AM65_CPSW_PN_REG_FIFO_STATUS);
+	*oper = !!(val & AM65_CPSW_PN_FST_EST_BUFACT);
+
+	val = readl(port->port_base + AM65_CPSW_PN_REG_EST_CTL);
+	*admin = !!(val & AM65_CPSW_PN_EST_BUFSEL);
+
+	return *admin == *oper;
+}
+
+/* am65_cpsw_port_est_get_free_buf_num() - Get free buffer number for
+ * Admin to program the new schedule.
+ *
+ * Logic as follows:-
+ * If oper is same as admin, return the other buffer (!oper) as the admin
+ * buffer.  If oper is not the same, driver let the current oper to continue
+ * as it is in the process of transitioning from admin -> oper. So keep the
+ * oper by selecting the same oper buffer by writing to EST_BUFSEL bit in
+ * EST CTL register. In the second iteration they will match and code returns.
+ * The actual buffer to write command is selected later before it is ready
+ * to update the schedule.
+ */
+static int am65_cpsw_port_est_get_free_buf_num(struct net_device *ndev)
+{
+	int oper, admin;
+	int roll = 2;
+
+	while (roll--) {
+		if (am65_cpsw_port_est_is_swapped(ndev, &oper, &admin))
+			return !oper;
+
+		/* admin is not set, so hinder transition as it's not allowed
+		 * to touch memory in-flight, by targeting same oper buf.
+		 */
+		am65_cpsw_port_est_assign_buf_num(ndev, oper);
+
+		dev_info(&ndev->dev,
+			 "Prev. EST admin cycle is in transit %d -> %d\n",
+			 oper, admin);
+	}
+
+	return admin;
+}
+
+static void am65_cpsw_admin_to_oper(struct net_device *ndev)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+
+	if (port->qos.est_oper)
+		devm_kfree(&ndev->dev, port->qos.est_oper);
+
+	port->qos.est_oper = port->qos.est_admin;
+	port->qos.est_admin = NULL;
+}
+
+static void am65_cpsw_port_est_get_buf_num(struct net_device *ndev,
+					   struct am65_cpsw_est *est_new)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	u32 val;
+
+	val = readl(port->port_base + AM65_CPSW_PN_REG_EST_CTL);
+	val &= ~AM65_CPSW_PN_EST_ONEBUF;
+	writel(val, port->port_base + AM65_CPSW_PN_REG_EST_CTL);
+
+	est_new->buf = am65_cpsw_port_est_get_free_buf_num(ndev);
+
+	/* rolled buf num means changed buf while configuring */
+	if (port->qos.est_oper && port->qos.est_admin &&
+	    est_new->buf == port->qos.est_oper->buf)
+		am65_cpsw_admin_to_oper(ndev);
+}
+
+static void am65_cpsw_est_set(struct net_device *ndev, int enable)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct am65_cpsw_common *common = port->common;
+	int common_enable = 0;
+	int i;
+
+	am65_cpsw_port_est_enable(port, enable);
+
+	for (i = 0; i < common->port_num; i++)
+		common_enable |= am65_cpsw_port_est_enabled(&common->ports[i]);
+
+	common_enable |= enable;
+	am65_cpsw_est_enable(common, common_enable);
+}
+
+/* This update is supposed to be used in any routine before getting real state
+ * of admin -> oper transition, particularly it's supposed to be used in some
+ * generic routine for providing real state to Taprio Qdisc.
+ */
+static void am65_cpsw_est_update_state(struct net_device *ndev)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	int oper, admin;
+
+	if (!port->qos.est_admin)
+		return;
+
+	if (!am65_cpsw_port_est_is_swapped(ndev, &oper, &admin))
+		return;
+
+	am65_cpsw_admin_to_oper(ndev);
+}
+
+/* Fetch command count it's number of bytes in Gigabit mode or nibbles in
+ * 10/100Mb mode. So, having speed and time in ns, recalculate ns to number of
+ * bytes/nibbles that can be sent while transmission on given speed.
+ */
+static int am65_est_cmd_ns_to_cnt(u64 ns, int link_speed)
+{
+	u64 temp;
+
+	temp = ns * link_speed;
+	if (link_speed < SPEED_1000)
+		temp <<= 1;
+
+	return DIV_ROUND_UP(temp, 8 * 1000);
+}
+
+static void __iomem *am65_cpsw_est_set_sched_cmds(void __iomem *addr,
+						  int fetch_cnt,
+						  int fetch_allow)
+{
+	u32 prio_mask, cmd_fetch_cnt, cmd;
+
+	do {
+		if (fetch_cnt > AM65_CPSW_FETCH_CNT_MAX) {
+			fetch_cnt -= AM65_CPSW_FETCH_CNT_MAX;
+			cmd_fetch_cnt = AM65_CPSW_FETCH_CNT_MAX;
+		} else {
+			cmd_fetch_cnt = fetch_cnt;
+			/* fetch count can't be less than 16? */
+			if (cmd_fetch_cnt && cmd_fetch_cnt < 16)
+				cmd_fetch_cnt = 16;
+
+			fetch_cnt = 0;
+		}
+
+		prio_mask = fetch_allow & AM65_CPSW_FETCH_ALLOW_MSK;
+		cmd = (cmd_fetch_cnt << AM65_CPSW_FETCH_CNT_OFFSET) | prio_mask;
+
+		writel(cmd, addr);
+		addr += 4;
+	} while (fetch_cnt);
+
+	return addr;
+}
+
+static int am65_cpsw_est_calc_cmd_num(struct net_device *ndev,
+				      struct tc_taprio_qopt_offload *taprio,
+				      int link_speed)
+{
+	int i, cmd_cnt, cmd_sum = 0;
+	u32 fetch_cnt;
+
+	for (i = 0; i < taprio->num_entries; i++) {
+		if (taprio->entries[i].command != TC_TAPRIO_CMD_SET_GATES) {
+			dev_err(&ndev->dev, "Only SET command is supported");
+			return -EINVAL;
+		}
+
+		fetch_cnt = am65_est_cmd_ns_to_cnt(taprio->entries[i].interval,
+						   link_speed);
+
+		cmd_cnt = DIV_ROUND_UP(fetch_cnt, AM65_CPSW_FETCH_CNT_MAX);
+		if (!cmd_cnt)
+			cmd_cnt++;
+
+		cmd_sum += cmd_cnt;
+
+		if (!fetch_cnt)
+			break;
+	}
+
+	return cmd_sum;
+}
+
+static int am65_cpsw_est_check_scheds(struct net_device *ndev,
+				      struct am65_cpsw_est *est_new)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	int cmd_num;
+
+	cmd_num = am65_cpsw_est_calc_cmd_num(ndev, &est_new->taprio,
+					     port->qos.link_speed);
+	if (cmd_num < 0)
+		return cmd_num;
+
+	if (cmd_num > AM65_CPSW_FETCH_RAM_CMD_NUM / 2) {
+		dev_err(&ndev->dev, "No fetch RAM");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static void am65_cpsw_est_set_sched_list(struct net_device *ndev,
+					 struct am65_cpsw_est *est_new)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	u32 fetch_cnt, fetch_allow, all_fetch_allow = 0;
+	void __iomem *ram_addr, *max_ram_addr;
+	struct tc_taprio_sched_entry *entry;
+	int i, ram_size;
+
+	ram_addr = port->fetch_ram_base;
+	ram_size = AM65_CPSW_FETCH_RAM_CMD_NUM * 2;
+	ram_addr += est_new->buf * ram_size;
+
+	max_ram_addr = ram_size + ram_addr;
+	for (i = 0; i < est_new->taprio.num_entries; i++) {
+		entry = &est_new->taprio.entries[i];
+
+		fetch_cnt = am65_est_cmd_ns_to_cnt(entry->interval,
+						   port->qos.link_speed);
+		fetch_allow = entry->gate_mask;
+		if (fetch_allow > AM65_CPSW_FETCH_ALLOW_MAX)
+			dev_dbg(&ndev->dev, "fetch_allow > 8 bits: %d\n",
+				fetch_allow);
+
+		ram_addr = am65_cpsw_est_set_sched_cmds(ram_addr, fetch_cnt,
+							fetch_allow);
+
+		if (!fetch_cnt && i < est_new->taprio.num_entries - 1) {
+			dev_info(&ndev->dev,
+				 "next scheds after %d have no impact", i + 1);
+			break;
+		}
+
+		all_fetch_allow |= fetch_allow;
+	}
+
+	/* end cmd, enabling non-timed queues for potential over cycle time */
+	if (ram_addr < max_ram_addr)
+		writel(~all_fetch_allow & AM65_CPSW_FETCH_ALLOW_MSK, ram_addr);
+}
+
+/**
+ * Enable ESTf periodic output, set cycle start time and interval.
+ */
+static int am65_cpsw_timer_set(struct net_device *ndev,
+			       struct am65_cpsw_est *est_new)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct am65_cpsw_common *common = port->common;
+	struct am65_cpts *cpts = common->cpts;
+	struct am65_cpts_estf_cfg cfg;
+
+	cfg.ns_period = est_new->taprio.cycle_time;
+	cfg.ns_start = est_new->taprio.base_time;
+
+	return am65_cpts_estf_enable(cpts, port->port_id - 1, &cfg);
+}
+
+static void am65_cpsw_timer_stop(struct net_device *ndev)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct am65_cpts *cpts = port->common->cpts;
+
+	am65_cpts_estf_disable(cpts, port->port_id - 1);
+}
+
+static enum timer_act am65_cpsw_timer_act(struct net_device *ndev,
+					  struct am65_cpsw_est *est_new)
+{
+	struct tc_taprio_qopt_offload *taprio_oper, *taprio_new;
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct am65_cpts *cpts = port->common->cpts;
+	u64 cur_time;
+	s64 diff;
+
+	if (!port->qos.est_oper)
+		return TACT_PROG;
+
+	taprio_new = &est_new->taprio;
+	taprio_oper = &port->qos.est_oper->taprio;
+
+	if (taprio_new->cycle_time != taprio_oper->cycle_time)
+		return TACT_NEED_STOP;
+
+	/* in order to avoid timer reset get base_time form oper taprio */
+	if (!taprio_new->base_time && taprio_oper)
+		taprio_new->base_time = taprio_oper->base_time;
+
+	if (taprio_new->base_time == taprio_oper->base_time)
+		return TACT_SKIP_PROG;
+
+	/* base times are cycle synchronized */
+	diff = taprio_new->base_time - taprio_oper->base_time;
+	diff = diff < 0 ? -diff : diff;
+	if (diff % taprio_new->cycle_time)
+		return TACT_NEED_STOP;
+
+	cur_time = am65_cpts_ns_gettime(cpts);
+	if (taprio_new->base_time <= cur_time + taprio_new->cycle_time)
+		return TACT_SKIP_PROG;
+
+	/* TODO: Admin schedule at future time is not currently supported */
+	return TACT_NEED_STOP;
+}
+
+static void am65_cpsw_stop_est(struct net_device *ndev)
+{
+	am65_cpsw_est_set(ndev, 0);
+	am65_cpsw_timer_stop(ndev);
+}
+
+static void am65_cpsw_purge_est(struct net_device *ndev)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+
+	am65_cpsw_stop_est(ndev);
+
+	if (port->qos.est_admin)
+		devm_kfree(&ndev->dev, port->qos.est_admin);
+
+	if (port->qos.est_oper)
+		devm_kfree(&ndev->dev, port->qos.est_oper);
+
+	port->qos.est_oper = NULL;
+	port->qos.est_admin = NULL;
+}
+
+static int am65_cpsw_configure_taprio(struct net_device *ndev,
+				      struct am65_cpsw_est *est_new)
+{
+	struct am65_cpsw_common *common = am65_ndev_to_common(ndev);
+	struct am65_cpts *cpts = common->cpts;
+	int ret = 0, tact = TACT_PROG;
+
+	am65_cpsw_est_update_state(ndev);
+
+	if (!est_new->taprio.enable) {
+		am65_cpsw_stop_est(ndev);
+		return ret;
+	}
+
+	ret = am65_cpsw_est_check_scheds(ndev, est_new);
+	if (ret < 0)
+		return ret;
+
+	tact = am65_cpsw_timer_act(ndev, est_new);
+	if (tact == TACT_NEED_STOP) {
+		dev_err(&ndev->dev,
+			"Can't toggle estf timer, stop taprio first");
+		return -EINVAL;
+	}
+
+	if (tact == TACT_PROG)
+		am65_cpsw_timer_stop(ndev);
+
+	if (!est_new->taprio.base_time)
+		est_new->taprio.base_time = am65_cpts_ns_gettime(cpts);
+
+	am65_cpsw_port_est_get_buf_num(ndev, est_new);
+	am65_cpsw_est_set_sched_list(ndev, est_new);
+	am65_cpsw_port_est_assign_buf_num(ndev, est_new->buf);
+
+	am65_cpsw_est_set(ndev, est_new->taprio.enable);
+
+	if (tact == TACT_PROG) {
+		ret = am65_cpsw_timer_set(ndev, est_new);
+		if (ret) {
+			dev_err(&ndev->dev, "Failed to set cycle time");
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static void am65_cpsw_cp_taprio(struct tc_taprio_qopt_offload *from,
+				struct tc_taprio_qopt_offload *to)
+{
+	int i;
+
+	*to = *from;
+	for (i = 0; i < from->num_entries; i++)
+		to->entries[i] = from->entries[i];
+}
+
+static int am65_cpsw_set_taprio(struct net_device *ndev, void *type_data)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct tc_taprio_qopt_offload *taprio = type_data;
+	struct am65_cpsw_est *est_new;
+	size_t size;
+	int ret = 0;
+
+	if (taprio->cycle_time_extension) {
+		dev_err(&ndev->dev, "Failed to set cycle time extension");
+		return -EOPNOTSUPP;
+	}
+
+	size = sizeof(struct tc_taprio_sched_entry) * taprio->num_entries +
+	       sizeof(struct am65_cpsw_est);
+
+	est_new = devm_kzalloc(&ndev->dev, size, GFP_KERNEL);
+	if (!est_new)
+		return -ENOMEM;
+
+	am65_cpsw_cp_taprio(taprio, &est_new->taprio);
+	ret = am65_cpsw_configure_taprio(ndev, est_new);
+	if (!ret) {
+		if (taprio->enable) {
+			if (port->qos.est_admin)
+				devm_kfree(&ndev->dev, port->qos.est_admin);
+
+			port->qos.est_admin = est_new;
+		} else {
+			devm_kfree(&ndev->dev, est_new);
+			am65_cpsw_purge_est(ndev);
+		}
+	} else {
+		devm_kfree(&ndev->dev, est_new);
+	}
+
+	return ret;
+}
+
+static void am65_cpsw_est_link_up(struct net_device *ndev, int link_speed)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	ktime_t cur_time;
+	s64 delta;
+
+	port->qos.link_speed = link_speed;
+	if (!am65_cpsw_port_est_enabled(port))
+		return;
+
+	if (port->qos.link_down_time) {
+		cur_time = ktime_get();
+		delta = ktime_us_delta(cur_time, port->qos.link_down_time);
+		if (delta > USEC_PER_SEC) {
+			dev_err(&ndev->dev,
+				"Link has been lost too long, stopping TAS");
+			goto purge_est;
+		}
+	}
+
+	return;
+
+purge_est:
+	am65_cpsw_purge_est(ndev);
+}
+
+static int am65_cpsw_setup_taprio(struct net_device *ndev, void *type_data)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+	struct am65_cpsw_common *common = port->common;
+
+	if (!IS_ENABLED(CONFIG_TI_AM65_CPSW_TAS))
+		return -ENODEV;
+
+	if (!netif_running(ndev)) {
+		dev_err(&ndev->dev, "interface is down, link speed unknown\n");
+		return -ENETDOWN;
+	}
+
+	if (common->pf_p0_rx_ptype_rrobin) {
+		dev_err(&ndev->dev,
+			"p0-rx-ptype-rrobin flag conflicts with taprio qdisc\n");
+		return -EINVAL;
+	}
+
+	if (port->qos.link_speed == SPEED_UNKNOWN)
+		return -ENOLINK;
+
+	return am65_cpsw_set_taprio(ndev, type_data);
+}
+
+int am65_cpsw_qos_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type,
+			       void *type_data)
+{
+	switch (type) {
+	case TC_SETUP_QDISC_TAPRIO:
+		return am65_cpsw_setup_taprio(ndev, type_data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+void am65_cpsw_qos_link_up(struct net_device *ndev, int link_speed)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+
+	if (!IS_ENABLED(CONFIG_TI_AM65_CPSW_TAS))
+		return;
+
+	am65_cpsw_est_link_up(ndev, link_speed);
+	port->qos.link_down_time = 0;
+}
+
+void am65_cpsw_qos_link_down(struct net_device *ndev)
+{
+	struct am65_cpsw_port *port = am65_ndev_to_port(ndev);
+
+	if (!IS_ENABLED(CONFIG_TI_AM65_CPSW_TAS))
+		return;
+
+	if (!port->qos.link_down_time)
+		port->qos.link_down_time = ktime_get();
+
+	port->qos.link_speed = SPEED_UNKNOWN;
+}
diff --git a/drivers/net/ethernet/ti/am65-cpsw-qos.h b/drivers/net/ethernet/ti/am65-cpsw-qos.h
new file mode 100644
index 000000000000..e8f1b6b59e93
--- /dev/null
+++ b/drivers/net/ethernet/ti/am65-cpsw-qos.h
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef AM65_CPSW_QOS_H_
+#define AM65_CPSW_QOS_H_
+
+#include <linux/netdevice.h>
+#include <net/pkt_sched.h>
+
+struct am65_cpsw_est {
+	int buf;
+	/* has to be the last one */
+	struct tc_taprio_qopt_offload taprio;
+};
+
+struct am65_cpsw_qos {
+	struct am65_cpsw_est *est_admin;
+	struct am65_cpsw_est *est_oper;
+	ktime_t link_down_time;
+	int link_speed;
+};
+
+int am65_cpsw_qos_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type,
+			       void *type_data);
+void am65_cpsw_qos_link_up(struct net_device *ndev, int link_speed);
+void am65_cpsw_qos_link_down(struct net_device *ndev);
+
+#endif /* AM65_CPSW_QOS_H_ */
-- 
2.17.1

Re: [PATCH net-next 0/2] am65-cpsw: add taprio/EST offload support

[David Miller]

From: Murali Karicheri <m-karicheri2@ti.com>
Date: Wed, 13 May 2020 09:26:13 -0400

> AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
> in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
> configuration. EST allows express queue traffic to be scheduled
> (placed) on the wire at specific repeatable time intervals. In
> Linux kernel, EST configuration is done through tc command and
> the taprio scheduler in the net core implements a software only
> scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
> user indicate "flag 2" in the command which is then parsed by
> taprio scheduler in net core and indicate that the command is to
> be offloaded to h/w. taprio then offloads the command to the
> driver by calling ndo_setup_tc() ndo ops. This patch implements
> ndo_setup_tc() as well as other changes required to offload EST
> configuration to CPSW h/w
> 
> For more details please refer patch 2/2.
 ...

Series applied, thank you.