[PATCH v1] gpio: octeon_gpio: Add GPIO controller driver for Octeon

* [PATCH v1] gpio: octeon_gpio: Add GPIO controller driver for Octeon
@ 2020-05-14 14:25 Stefan Roese
  2020-05-25 17:03 ` Simon Glass
  0 siblings, 1 reply; 3+ messages in thread
From: Stefan Roese @ 2020-05-14 14:25 UTC (permalink / raw)
  To: u-boot

From: Suneel Garapati <sgarapati@marvell.com>

Add support for GPIO controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
---
RFC -> v1 (Stefan)
- Separated this patch from the OcteonTX/TX2 RFC patch series into a
  single patch. This is useful, as the upcoming MIPS Octeon support will
  use this GPIO driver.
- Added MIPS Octeon II/III support (big endian). Rename driver and its
  function names from "octeontx" to "octeon" to better match all Octeon
  platforms.
- Moved from union to defines / bitmasks. This makes the driver usage
  on little- and big-endian platforms much easier.
- Used clrbits_64() instead of clrbits_le64() and friends to support
  usage on little- and big-endian systems
- Removed dev->req_seq assignment
- Enhanced Kconfig text
- Rewrote GPIO_BIT macro
- Dropped many macros to calculate the registers offsets and implemented
  simple functions for this (easier to read)
- Used GENMASK_ULL and FIELD_GET helpers
- Minor cosmetic changes (dropped brackets etc)
- Reword commit text and subject

 drivers/gpio/Kconfig       |  10 ++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/octeon_gpio.c | 241 +++++++++++++++++++++++++++++++++++++
 3 files changed, 252 insertions(+)
 create mode 100644 drivers/gpio/octeon_gpio.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 2081520f42..9c72930268 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -316,6 +316,16 @@ config PIC32_GPIO
 	help
 	  Say yes here to support Microchip PIC32 GPIOs.
 
+config OCTEON_GPIO
+	bool "Octeon II/III/TX/TX2 GPIO driver"
+	depends on DM_GPIO && (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
+	default y
+	help
+	  Add support for the Marvell Octeon GPIO driver. This is used with
+	  various Octeon parts such as Octeon II/III and OcteonTX/TX2.
+	  Octeon II/III has 32 GPIOs (count defined via DT) and OcteonTX/TX2
+	  has 64 GPIOs (count defined via internal register).
+
 config STM32_GPIO
 	bool "ST STM32 GPIO driver"
 	depends on DM_GPIO && (STM32 || ARCH_STM32MP)
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 7638259007..eb6364adb4 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -58,6 +58,7 @@ obj-$(CONFIG_HIKEY_GPIO)	+= hi6220_gpio.o
 obj-$(CONFIG_HSDK_CREG_GPIO)	+= hsdk-creg-gpio.o
 obj-$(CONFIG_IMX_RGPIO2P)	+= imx_rgpio2p.o
 obj-$(CONFIG_PIC32_GPIO)	+= pic32_gpio.o
+obj-$(CONFIG_OCTEON_GPIO)	+= octeon_gpio.o
 obj-$(CONFIG_MVEBU_GPIO)	+= mvebu_gpio.o
 obj-$(CONFIG_MSM_GPIO)		+= msm_gpio.o
 obj-$(CONFIG_$(SPL_)PCF8575_GPIO)	+= pcf8575_gpio.o
diff --git a/drivers/gpio/octeon_gpio.c b/drivers/gpio/octeon_gpio.c
new file mode 100644
index 0000000000..8079f6c5d9
--- /dev/null
+++ b/drivers/gpio/octeon_gpio.c
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier:    GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * (C) Copyright 2011
+ * eInfochips Ltd. <www.einfochips.com>
+ * Written-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
+ *
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <pci_ids.h>
+#include <asm/bitops.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <linux/bitfield.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/* Returns the bit value to write or read based on the offset */
+#define GPIO_BIT(x)		BIT_ULL((x) & 0x3f)
+
+/* Some offsets which are different on Octeon & OcteonTX/TX2 */
+#if defined(CONFIG_ARCH_OCTEON)
+#define REG_OFFS		0x80
+#define GPIO_BIT_CFG_OFFS	0x100
+#else
+#define REG_OFFS		0x00
+#define GPIO_BIT_CFG_OFFS	0x400
+#endif
+
+#define GPIO_RX_DAT		(REG_OFFS + 0x00)
+#define GPIO_TX_SET		(REG_OFFS + 0x08)
+#define GPIO_TX_CLR		(REG_OFFS + 0x10)
+#define GPIO_CONST		(REG_OFFS + 0x90)	/* OcteonTX only */
+
+/* Offset to register-set for 2nd GPIOs (> 63), OcteonTX only */
+#define GPIO1_OFFSET		0x1400
+
+/* GPIO_CONST register bits */
+#define GPIO_CONST_GPIOS_MASK	GENMASK_ULL(7, 0)
+
+/* GPIO_BIT_CFG register bits */
+#define GPIO_BIT_CFG_TX_OE	BIT_ULL(0)
+#define GPIO_BIT_CFG_PIN_XOR	BIT_ULL(1)
+#define GPIO_BIT_CFG_INT_EN	BIT_ULL(2)
+#define GPIO_BIT_CFG_PIN_SEL_MASK GENMASK_ULL(26, 16)
+
+struct octeon_gpio {
+	void __iomem *base;
+};
+
+/* Returns the offset to the output register based on the offset and value */
+static u32 gpio_tx_reg(int offset, int value)
+{
+	u32 ret;
+
+	ret = value ? GPIO_TX_SET : GPIO_TX_CLR;
+	if (offset > 63)
+		ret += GPIO1_OFFSET;
+
+	return ret;
+}
+
+/* Returns the offset to the input data register based on the offset */
+static u32 gpio_rx_dat_reg(int offset)
+{
+	u32 ret;
+
+	ret = GPIO_RX_DAT;
+	if (offset > 63)
+		ret += GPIO1_OFFSET;
+
+	return ret;
+}
+
+/* Returns the bit configuration register based on the offset */
+static u32 gpio_bit_cfg_reg(int offset)
+{
+	return GPIO_BIT_CFG_OFFS + 8 * offset;
+}
+
+static int octeon_gpio_dir_input(struct udevice *dev, unsigned int offset)
+{
+	struct octeon_gpio *gpio = dev_get_priv(dev);
+
+	debug("%s(%s, %u)\n", __func__, dev->name, offset);
+	clrbits_64(gpio->base + gpio_bit_cfg_reg(offset),
+		   GPIO_BIT_CFG_TX_OE | GPIO_BIT_CFG_PIN_XOR |
+		   GPIO_BIT_CFG_INT_EN | GPIO_BIT_CFG_PIN_SEL_MASK);
+
+	return 0;
+}
+
+static int octeon_gpio_dir_output(struct udevice *dev, unsigned int offset,
+				  int value)
+{
+	struct octeon_gpio *gpio = dev_get_priv(dev);
+
+	debug("%s(%s, %u, %d)\n", __func__, dev->name, offset, value);
+	writeq(GPIO_BIT(offset), gpio->base + gpio_tx_reg(offset, value));
+
+	clrsetbits_64(gpio->base + gpio_bit_cfg_reg(offset),
+		      GPIO_BIT_CFG_PIN_SEL_MASK | GPIO_BIT_CFG_INT_EN,
+		      GPIO_BIT_CFG_TX_OE);
+
+	return 0;
+}
+
+static int octeon_gpio_get_value(struct udevice *dev, unsigned int offset)
+{
+	struct octeon_gpio *gpio = dev_get_priv(dev);
+	u64 reg = readq(gpio->base + gpio_rx_dat_reg(offset));
+
+	debug("%s(%s, %u): value: %d\n", __func__, dev->name, offset,
+	      !!(reg & GPIO_BIT(offset)));
+
+	return !!(reg & GPIO_BIT(offset));
+}
+
+static int octeon_gpio_set_value(struct udevice *dev,
+				 unsigned int offset, int value)
+{
+	struct octeon_gpio *gpio = dev_get_priv(dev);
+
+	debug("%s(%s, %u, %d)\n", __func__, dev->name, offset, value);
+	writeq(GPIO_BIT(offset), gpio->base + gpio_tx_reg(offset, value));
+
+	return 0;
+}
+
+static int octeon_gpio_get_function(struct udevice *dev, unsigned int offset)
+{
+	struct octeon_gpio *gpio = dev_get_priv(dev);
+	u64 val = readq(gpio->base + gpio_bit_cfg_reg(offset));
+	int pin_sel;
+
+	debug("%s(%s, %u): GPIO_BIT_CFG: 0x%llx\n", __func__, dev->name,
+	      offset, val);
+	pin_sel = FIELD_GET(GPIO_BIT_CFG_PIN_SEL_MASK, val);
+	if (pin_sel)
+		return GPIOF_FUNC;
+	else if (val & GPIO_BIT_CFG_TX_OE)
+		return GPIOF_OUTPUT;
+	else
+		return GPIOF_INPUT;
+}
+
+static int octeon_gpio_xlate(struct udevice *dev, struct gpio_desc *desc,
+			     struct ofnode_phandle_args *args)
+{
+	if (args->args_count < 1)
+		return -EINVAL;
+
+	desc->offset = args->args[0];
+	desc->flags = 0;
+	if (args->args_count > 1) {
+		if (args->args[1] & GPIO_ACTIVE_LOW)
+			desc->flags |= GPIOD_ACTIVE_LOW;
+		/* In the future add tri-state flag support */
+	}
+	return 0;
+}
+
+static const struct dm_gpio_ops octeon_gpio_ops = {
+	.direction_input	= octeon_gpio_dir_input,
+	.direction_output	= octeon_gpio_dir_output,
+	.get_value		= octeon_gpio_get_value,
+	.set_value		= octeon_gpio_set_value,
+	.get_function		= octeon_gpio_get_function,
+	.xlate			= octeon_gpio_xlate,
+};
+
+static int octeon_gpio_probe(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+	struct octeon_gpio *priv = dev_get_priv(dev);
+	char *end;
+#if !defined(CONFIG_ARCH_OCTEON)
+	pci_dev_t bdf = dm_pci_get_bdf(dev);
+#endif
+
+#if !defined(CONFIG_ARCH_OCTEON)
+	priv->base = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0,
+				    PCI_REGION_MEM);
+#else
+	priv->base = dev_remap_addr(dev);
+#endif
+	if (!priv->base) {
+		debug("%s(%s): Could not get base address\n",
+		      __func__, dev->name);
+		return -1;
+	}
+
+#if !defined(CONFIG_ARCH_OCTEON)
+	uc_priv->gpio_count = readq(priv->base + GPIO_CONST) &
+		GPIO_CONST_GPIOS_MASK;
+#else
+	uc_priv->gpio_count = ofnode_read_u32_default(dev->node,
+						      "nr-gpios", 32);
+#endif
+
+	uc_priv->bank_name  = strdup(dev->name);
+	end = strchr(uc_priv->bank_name, '@');
+	end[0] = 'A' + dev->seq;
+	end[1] = '\0';
+
+	debug("%s(%s): base address: %p, pin count: %d\n",
+	      __func__, dev->name, priv->base, uc_priv->gpio_count);
+
+	return 0;
+}
+
+static const struct udevice_id octeon_gpio_ids[] = {
+	{ .compatible = "cavium,thunder-8890-gpio" },
+	{ .compatible = "cavium,octeon-7890-gpio" },
+	{ }
+};
+
+U_BOOT_DRIVER(octeon_gpio) = {
+	.name	= "octeon_gpio",
+	.id	= UCLASS_GPIO,
+	.of_match = of_match_ptr(octeon_gpio_ids),
+	.probe = octeon_gpio_probe,
+	.priv_auto_alloc_size = sizeof(struct octeon_gpio),
+	.ops	= &octeon_gpio_ops,
+	.flags	= DM_FLAG_PRE_RELOC,
+};
+
+#if !defined(CONFIG_ARCH_OCTEON)
+static struct pci_device_id octeon_gpio_supported[] = {
+	{ PCI_VDEVICE(CAVIUM, PCI_DEVICE_ID_CAVIUM_GPIO) },
+	{ },
+};
+
+U_BOOT_PCI_DEVICE(octeon_gpio, octeontx_gpio_supported);
+#endif
-- 
2.26.2

^ permalink raw reply related	[flat|nested] 3+ messages in thread