* [PATCH v7 0/5] mainline Protonic boards
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, linux-kernel, Oleksij Rempel, NXP Linux Team,
Pengutronix Kernel Team, Fabio Estevam, linux-arm-kernel
changes v7:
- VT7: reorder node alphabetically
- VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
- VT7: remove panel and TS nodes. This drivers are currently not
mainline.
- prti6q.dtsi: move reg_1v8 to prti6q.dts
- prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
every board file.
changes v6:
- move fsl.yaml changes to separate patch
- remove partitions, they are provided by the bootloader
- update flash compatible
- rename can3 to can
- fix fsl,mode
- fix interrupt in the wlan node on PRTI6Q
changes v5:
- PRTI6Q: remove status from the pwm-backlight node
- drop the vendor-prefixes patch, it is already taken by Rob
- add Reviewed-by: Rob Herring <robh@kernel.org>
changes v4:
- VT7: fix typo
changes v3:
- move compatible to the start of node
- move status to the end
- use generic names in compatible
- refactor dts/dtsi
- use alphabet order for pinctrl and phandels
- remove unused or currently not supported nodes
changes v2:
- squash PRTI6Q patches
Oleksij Rempel (5):
ARM: dts: add Protonic PRTI6Q board
ARM: dts: add Protonic WD2 board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic RVT board
dt-bindings: arm: fsl: add different Protonic boards
.../devicetree/bindings/arm/fsl.yaml | 4 +
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++
arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++
arch/arm/boot/dts/imx6q-prti6q.dts | 529 ++++++++++++++++++
arch/arm/boot/dts/imx6q-prtwd2.dts | 188 +++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 174 ++++++
7 files changed, 1553 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v7 1/5] ARM: dts: add Protonic PRTI6Q board
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 9:29 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Rob Herring, David Jander, devicetree,
Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prti6q.dts | 529 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 174 +++++++++
3 files changed, 704 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd992013973..206a36a50575e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -538,6 +538,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-nymph.dtb \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
+ imx6q-prti6q.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
new file mode 100644
index 0000000000000..e698149cab423
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -0,0 +1,529 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <16>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ can3_25m_osc: can3-25m-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-debug1 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_wifi: regulator-wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "regulator-WL12xx";
+ startup-delay-us = <70000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can3>;
+ clocks = <&can3_25m_osc>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <5000000>;
+ };
+
+ adc@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ vref-supply = <®_3v3>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* can2_l */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can2_h */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "ac97-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ vmmc-supply = <®_wifi>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wifi {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi>;
+ interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_can3: can3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg_id: usbotgidgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 0000000000000..ed526d185f959
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+};
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v7 1/5] ARM: dts: add Protonic PRTI6Q board
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, Rob Herring, linux-kernel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prti6q.dts | 529 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 174 +++++++++
3 files changed, 704 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd992013973..206a36a50575e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -538,6 +538,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-nymph.dtb \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
+ imx6q-prti6q.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
new file mode 100644
index 0000000000000..e698149cab423
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -0,0 +1,529 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <16>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ can3_25m_osc: can3-25m-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-debug1 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_wifi: regulator-wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "regulator-WL12xx";
+ startup-delay-us = <70000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can3>;
+ clocks = <&can3_25m_osc>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <5000000>;
+ };
+
+ adc@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ vref-supply = <®_3v3>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* can2_l */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can2_h */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "ac97-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ vmmc-supply = <®_wifi>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wifi {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi>;
+ interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_can3: can3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg_id: usbotgidgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 0000000000000..ed526d185f959
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+};
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v7 2/5] ARM: dts: add Protonic WD2 board
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 9:29 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Rob Herring, David Jander, devicetree,
Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prtwd2.dts | 188 +++++++++++++++++++++++++++++
2 files changed, 189 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 206a36a50575e..8ce744f1cbfc9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -539,6 +539,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
imx6q-prti6q.dtb \
+ imx6q-prtwd2.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prtwd2.dts b/arch/arm/boot/dts/imx6q-prtwd2.dts
new file mode 100644
index 0000000000000..fd9f457a273e2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prtwd2.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2018 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic WD2 board";
+ compatible = "prt,prtwd2", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
+ i2c@4 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ i2c-gpio,delay-us = <20>; /* ~10 kHz */
+ i2c-gpio,scl-output-only;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ pause;
+ full-duplex;
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* V in */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* I charge */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* V bus */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ no-1-8-v;
+ non-removable;
+ mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+ pm-ignore-notify;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_eth_chg>;
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
+ MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
+ >;
+ };
+
+ pinctrl_usb_eth_chg: usbethchggrp {
+ fsl,pins = <
+ /* USB charging control */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+};
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v7 2/5] ARM: dts: add Protonic WD2 board
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, Rob Herring, linux-kernel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prtwd2.dts | 188 +++++++++++++++++++++++++++++
2 files changed, 189 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 206a36a50575e..8ce744f1cbfc9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -539,6 +539,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
imx6q-prti6q.dtb \
+ imx6q-prtwd2.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prtwd2.dts b/arch/arm/boot/dts/imx6q-prtwd2.dts
new file mode 100644
index 0000000000000..fd9f457a273e2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prtwd2.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2018 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic WD2 board";
+ compatible = "prt,prtwd2", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
+ i2c@4 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ i2c-gpio,delay-us = <20>; /* ~10 kHz */
+ i2c-gpio,scl-output-only;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ pause;
+ full-duplex;
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* V in */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* I charge */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* V bus */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ no-1-8-v;
+ non-removable;
+ mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+ pm-ignore-notify;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_eth_chg>;
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
+ MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
+ >;
+ };
+
+ pinctrl_usb_eth_chg: usbethchggrp {
+ fsl,pins = <
+ /* USB charging control */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+};
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v7 3/5] ARM: dts: add Protonic VT7 board
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 9:29 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Rob Herring, Robin van der Gracht, David Jander,
devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel,
NXP Linux Team, Pengutronix Kernel Team
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++
2 files changed, 473 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8ce744f1cbfc9..66ee89e7929f9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
imx6dl-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
new file mode 100644
index 0000000000000..70e80195d648a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -0,0 +1,472 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic VT7";
+ compatible = "prt,prtvt7", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ brightness-levels = <0 20 81 248 1000>;
+ default-brightness-level = <20>;
+ num-interpolated-steps = <21>;
+ power-supply = <®_12v_bl>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ esc {
+ label = "GPIO Key ESC";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+ };
+
+ up {
+ label = "GPIO Key UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+ };
+
+ down {
+ label = "GPIO Key DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+ };
+
+ enter {
+ label = "GPIO Key Enter";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+ };
+
+ cycle {
+ label = "GPIO Key CYCLE";
+ linux,code = <KEY_CYCLEWINDOWS>;
+ gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+ };
+
+ f1 {
+ label = "GPIO Key F1";
+ linux,code = <KEY_F1>;
+ gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+ };
+
+ f2 {
+ label = "GPIO Key F2";
+ linux,code = <KEY_F2>;
+ gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+ };
+
+ f3 {
+ label = "GPIO Key F3";
+ linux,code = <KEY_F3>;
+ gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+ };
+
+ f4 {
+ label = "GPIO Key F4";
+ linux,code = <KEY_F4>;
+ gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+ };
+
+ f5 {
+ label = "GPIO Key F5";
+ linux,code = <KEY_F5>;
+ gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+ };
+
+ f6 {
+ label = "GPIO Key F6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+ };
+
+ f7 {
+ label = "GPIO Key F7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+ };
+
+ f8 {
+ label = "GPIO Key F8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+ };
+
+ f9 {
+ label = "GPIO Key F9";
+ linux,code = <KEY_F9>;
+ gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+ };
+
+ f10 {
+ label = "GPIO Key F10";
+ linux,code = <KEY_F10>;
+ gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "innolux,g070y2t0ec";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ reg_12v_bl: regulator-bl-12v {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_12v_bl>;
+ regulator-name = "12v-bl";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ tsc@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ vcc-supply = <®_3v3>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <8000>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <4800>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+ ti,pressure-max = /bits/ 16 <4095>;
+
+ ti,skip-samples = <2>;
+ ti,sample-period-msecs = <10>;
+ ti,report-period-msecs = <30>;
+
+ ti,filter-tolerance = <80>;
+ ti,touch-resistance-threshold = <3500>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&i2c1 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_codec>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+&i2c3 {
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ gpio_pca: gpio@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&ipu1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_codec: codecgrp {
+ fsl,pins = <
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_12v_bl: 12blgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+};
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v7 3/5] ARM: dts: add Protonic VT7 board
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, Rob Herring, Robin van der Gracht, linux-kernel,
Oleksij Rempel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Fabio Estevam, linux-arm-kernel
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++++++++++++++
2 files changed, 473 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8ce744f1cbfc9..66ee89e7929f9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
imx6dl-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
new file mode 100644
index 0000000000000..70e80195d648a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -0,0 +1,472 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic VT7";
+ compatible = "prt,prtvt7", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ brightness-levels = <0 20 81 248 1000>;
+ default-brightness-level = <20>;
+ num-interpolated-steps = <21>;
+ power-supply = <®_12v_bl>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ esc {
+ label = "GPIO Key ESC";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+ };
+
+ up {
+ label = "GPIO Key UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+ };
+
+ down {
+ label = "GPIO Key DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+ };
+
+ enter {
+ label = "GPIO Key Enter";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+ };
+
+ cycle {
+ label = "GPIO Key CYCLE";
+ linux,code = <KEY_CYCLEWINDOWS>;
+ gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+ };
+
+ f1 {
+ label = "GPIO Key F1";
+ linux,code = <KEY_F1>;
+ gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+ };
+
+ f2 {
+ label = "GPIO Key F2";
+ linux,code = <KEY_F2>;
+ gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+ };
+
+ f3 {
+ label = "GPIO Key F3";
+ linux,code = <KEY_F3>;
+ gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+ };
+
+ f4 {
+ label = "GPIO Key F4";
+ linux,code = <KEY_F4>;
+ gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+ };
+
+ f5 {
+ label = "GPIO Key F5";
+ linux,code = <KEY_F5>;
+ gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+ };
+
+ f6 {
+ label = "GPIO Key F6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+ };
+
+ f7 {
+ label = "GPIO Key F7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+ };
+
+ f8 {
+ label = "GPIO Key F8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+ };
+
+ f9 {
+ label = "GPIO Key F9";
+ linux,code = <KEY_F9>;
+ gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+ };
+
+ f10 {
+ label = "GPIO Key F10";
+ linux,code = <KEY_F10>;
+ gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "innolux,g070y2t0ec";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ reg_12v_bl: regulator-bl-12v {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_12v_bl>;
+ regulator-name = "12v-bl";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ tsc@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ vcc-supply = <®_3v3>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <8000>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <4800>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+ ti,pressure-max = /bits/ 16 <4095>;
+
+ ti,skip-samples = <2>;
+ ti,sample-period-msecs = <10>;
+ ti,report-period-msecs = <30>;
+
+ ti,filter-tolerance = <80>;
+ ti,touch-resistance-threshold = <3500>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&i2c1 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_codec>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+&i2c3 {
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ gpio_pca: gpio@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&ipu1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_codec: codecgrp {
+ fsl,pins = <
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_12v_bl: 12blgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+};
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v7 4/5] ARM: dts: add Protonic RVT board
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 9:29 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, Rob Herring, David Jander, devicetree,
Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++++++++++++++++++++++++
2 files changed, 183 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 66ee89e7929f9..89842a034e4ba 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/imx6dl-prtrvt.dts
new file mode 100644
index 0000000000000..b7721e52a463a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+
+ nfc@0 {
+ compatible = "ti,trf7970a";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nfc>;
+ spi-max-frequency = <2000000>;
+ interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
+ ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
+ <&gpio5 11 GPIO_ACTIVE_LOW>;
+ vin-supply = <®_3v3>;
+ vin-voltage-override = <3100000>;
+ autosuspend-delay = <30000>;
+ irq-status-read-quirk;
+ en2-rf-quirk;
+ t5t-rmb-extra-byte-quirk;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* nc */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_nfc: nfcgrp {
+ fsl,pins = <
+ /* NFC_ASK_OOK */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
+ /* NFC_PWR_EN */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
+ /* NFC_EN2 */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
+ /* NFC_EN */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+ /* NFC_MOD */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
+ /* NFC_IRQ */
+ MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
+ >;
+ };
+};
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v7 4/5] ARM: dts: add Protonic RVT board
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, Rob Herring, linux-kernel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++++++++++++++++++++++++
2 files changed, 183 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 66ee89e7929f9..89842a034e4ba 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -450,6 +450,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/imx6dl-prtrvt.dts
new file mode 100644
index 0000000000000..b7721e52a463a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+
+ nfc@0 {
+ compatible = "ti,trf7970a";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nfc>;
+ spi-max-frequency = <2000000>;
+ interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
+ ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
+ <&gpio5 11 GPIO_ACTIVE_LOW>;
+ vin-supply = <®_3v3>;
+ vin-voltage-override = <3100000>;
+ autosuspend-delay = <30000>;
+ irq-status-read-quirk;
+ en2-rf-quirk;
+ t5t-rmb-extra-byte-quirk;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* nc */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_nfc: nfcgrp {
+ fsl,pins = <
+ /* NFC_ASK_OOK */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
+ /* NFC_PWR_EN */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
+ /* NFC_EN2 */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
+ /* NFC_EN */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+ /* NFC_MOD */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
+ /* NFC_IRQ */
+ MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
+ >;
+ };
+};
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v7 5/5] dt-bindings: arm: fsl: add different Protonic boards
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 9:29 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team
Add Protonic PRTI6Q, WD2, RVT, VT7 boards.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index cd3fbe7e39487..a1657505b3357 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -119,6 +119,8 @@ properties:
- fsl,imx6q-sabreauto
- fsl,imx6q-sabrelite
- fsl,imx6q-sabresd
+ - prt,prti6q # Protonic PRTI6Q board
+ - prt,prtwd2 # Protonic WD2 board
- technexion,imx6q-pico-dwarf # TechNexion i.MX6Q Pico-Dwarf
- technexion,imx6q-pico-hobbit # TechNexion i.MX6Q Pico-Hobbit
- technexion,imx6q-pico-nymph # TechNexion i.MX6Q Pico-Nymph
@@ -170,6 +172,8 @@ properties:
- emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base
- fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
+ - prt,prtrvt # Protonic RVT board
+ - prt,prtvt7 # Protonic VT7 board
- technexion,imx6dl-pico-dwarf # TechNexion i.MX6DL Pico-Dwarf
- technexion,imx6dl-pico-hobbit # TechNexion i.MX6DL Pico-Hobbit
- technexion,imx6dl-pico-nymph # TechNexion i.MX6DL Pico-Nymph
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v7 5/5] dt-bindings: arm: fsl: add different Protonic boards
@ 2020-05-20 9:29 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 9:29 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, linux-kernel, Oleksij Rempel, NXP Linux Team,
Pengutronix Kernel Team, Fabio Estevam, linux-arm-kernel
Add Protonic PRTI6Q, WD2, RVT, VT7 boards.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index cd3fbe7e39487..a1657505b3357 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -119,6 +119,8 @@ properties:
- fsl,imx6q-sabreauto
- fsl,imx6q-sabrelite
- fsl,imx6q-sabresd
+ - prt,prti6q # Protonic PRTI6Q board
+ - prt,prtwd2 # Protonic WD2 board
- technexion,imx6q-pico-dwarf # TechNexion i.MX6Q Pico-Dwarf
- technexion,imx6q-pico-hobbit # TechNexion i.MX6Q Pico-Hobbit
- technexion,imx6q-pico-nymph # TechNexion i.MX6Q Pico-Nymph
@@ -170,6 +172,8 @@ properties:
- emtrion,emcon-mx6-avari # emCON-MX6S or emCON-MX6DL SoM on Avari Base
- fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
+ - prt,prtrvt # Protonic RVT board
+ - prt,prtvt7 # Protonic VT7 board
- technexion,imx6dl-pico-dwarf # TechNexion i.MX6DL Pico-Dwarf
- technexion,imx6dl-pico-hobbit # TechNexion i.MX6DL Pico-Hobbit
- technexion,imx6dl-pico-nymph # TechNexion i.MX6DL Pico-Nymph
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v7 0/5] mainline Protonic boards
2020-05-20 9:29 ` Oleksij Rempel
@ 2020-05-20 15:19 ` Oleksij Rempel
-1 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 15:19 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel,
NXP Linux Team, Pengutronix Kernel Team
[-- Attachment #1: Type: text/plain, Size: 2638 bytes --]
Please ignore this version, i used wrong commit hash to format-patch.
On Wed, May 20, 2020 at 11:29:32AM +0200, Oleksij Rempel wrote:
> changes v7:
> - VT7: reorder node alphabetically
> - VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
> - VT7: remove panel and TS nodes. This drivers are currently not
> mainline.
> - prti6q.dtsi: move reg_1v8 to prti6q.dts
> - prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
> every board file.
>
> changes v6:
> - move fsl.yaml changes to separate patch
> - remove partitions, they are provided by the bootloader
> - update flash compatible
> - rename can3 to can
> - fix fsl,mode
> - fix interrupt in the wlan node on PRTI6Q
>
> changes v5:
> - PRTI6Q: remove status from the pwm-backlight node
> - drop the vendor-prefixes patch, it is already taken by Rob
> - add Reviewed-by: Rob Herring <robh@kernel.org>
>
> changes v4:
> - VT7: fix typo
>
> changes v3:
> - move compatible to the start of node
> - move status to the end
> - use generic names in compatible
> - refactor dts/dtsi
> - use alphabet order for pinctrl and phandels
> - remove unused or currently not supported nodes
>
> changes v2:
> - squash PRTI6Q patches
>
> Oleksij Rempel (5):
> ARM: dts: add Protonic PRTI6Q board
> ARM: dts: add Protonic WD2 board
> ARM: dts: add Protonic VT7 board
> ARM: dts: add Protonic RVT board
> dt-bindings: arm: fsl: add different Protonic boards
>
> .../devicetree/bindings/arm/fsl.yaml | 4 +
> arch/arm/boot/dts/Makefile | 4 +
> arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++
> arch/arm/boot/dts/imx6q-prti6q.dts | 529 ++++++++++++++++++
> arch/arm/boot/dts/imx6q-prtwd2.dts | 188 +++++++
> arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 174 ++++++
> 7 files changed, 1553 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
> create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
> create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
>
> --
> 2.26.2
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v7 0/5] mainline Protonic boards
@ 2020-05-20 15:19 ` Oleksij Rempel
0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2020-05-20 15:19 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: devicetree, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, Fabio Estevam, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2638 bytes --]
Please ignore this version, i used wrong commit hash to format-patch.
On Wed, May 20, 2020 at 11:29:32AM +0200, Oleksij Rempel wrote:
> changes v7:
> - VT7: reorder node alphabetically
> - VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
> - VT7: remove panel and TS nodes. This drivers are currently not
> mainline.
> - prti6q.dtsi: move reg_1v8 to prti6q.dts
> - prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
> every board file.
>
> changes v6:
> - move fsl.yaml changes to separate patch
> - remove partitions, they are provided by the bootloader
> - update flash compatible
> - rename can3 to can
> - fix fsl,mode
> - fix interrupt in the wlan node on PRTI6Q
>
> changes v5:
> - PRTI6Q: remove status from the pwm-backlight node
> - drop the vendor-prefixes patch, it is already taken by Rob
> - add Reviewed-by: Rob Herring <robh@kernel.org>
>
> changes v4:
> - VT7: fix typo
>
> changes v3:
> - move compatible to the start of node
> - move status to the end
> - use generic names in compatible
> - refactor dts/dtsi
> - use alphabet order for pinctrl and phandels
> - remove unused or currently not supported nodes
>
> changes v2:
> - squash PRTI6Q patches
>
> Oleksij Rempel (5):
> ARM: dts: add Protonic PRTI6Q board
> ARM: dts: add Protonic WD2 board
> ARM: dts: add Protonic VT7 board
> ARM: dts: add Protonic RVT board
> dt-bindings: arm: fsl: add different Protonic boards
>
> .../devicetree/bindings/arm/fsl.yaml | 4 +
> arch/arm/boot/dts/Makefile | 4 +
> arch/arm/boot/dts/imx6dl-prtrvt.dts | 182 ++++++
> arch/arm/boot/dts/imx6dl-prtvt7.dts | 472 ++++++++++++++++
> arch/arm/boot/dts/imx6q-prti6q.dts | 529 ++++++++++++++++++
> arch/arm/boot/dts/imx6q-prtwd2.dts | 188 +++++++
> arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 174 ++++++
> 7 files changed, 1553 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
> create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
> create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
>
> --
> 2.26.2
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread