* [PATCH v2 1/2] dt-bindings: arm: fsl: Add MYiR Tech boards
@ 2020-06-01 14:58 ` Parthiban Nallathambi
0 siblings, 0 replies; 8+ messages in thread
From: Parthiban Nallathambi @ 2020-06-01 14:58 UTC (permalink / raw)
To: m.felsch, shawnguo, robh+dt, s.hauer
Cc: devicetree, Parthiban Nallathambi, linux-kernel, linux-imx,
kernel, festevam, linux-arm-kernel
Add entries for MYiR Tech imx6ULL eval boards.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index cd3fbe7e3948..592d73187da4 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -264,6 +264,8 @@ properties:
- armadeus,imx6ull-opos6uldev # OPOS6UL (i.MX6ULL) SoM on OPOS6ULDev board
- fsl,imx6ull-14x14-evk # i.MX6 UltraLiteLite 14x14 EVK Board
- kontron,imx6ull-n6411-som # Kontron N6411 SOM
+ - myir,imx6ull-mys-6ulx # MYiR Tech iMX6ULL Evaluation Board
+ - myir,imx6ull-mys-6ulx-nand # MYiR Tech iMX6ULL Evaluation Board with NAND
- toradex,colibri-imx6ull-eval # Colibri iMX6ULL Module on Colibri Evaluation Board
- toradex,colibri-imx6ull-wifi-eval # Colibri iMX6ULL Wi-Fi / Bluetooth Module on Colibri Evaluation Board
- const: fsl,imx6ull
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v2 2/2] ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
2020-06-01 14:58 ` Parthiban Nallathambi
@ 2020-06-01 14:58 ` Parthiban Nallathambi
-1 siblings, 0 replies; 8+ messages in thread
From: Parthiban Nallathambi @ 2020-06-01 14:58 UTC (permalink / raw)
To: m.felsch, shawnguo, robh+dt, s.hauer
Cc: kernel, festevam, linux-imx, devicetree, linux-kernel,
linux-arm-kernel, Parthiban Nallathambi
Add support for the MYiR imx6ULL based single board computer
equipped with on board 256MB NAND & RAM. The board also
provides expansion header for expansion board, but this
commit adds only support for SBC.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
---
Notes:
Changelog v2:
- moved regulator under root node
- status property removed
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-myir-mys-6ulx-nand.dts | 19 ++
arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi | 238 ++++++++++++++++++
3 files changed, 258 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd99201397..eab86051d782 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -612,6 +612,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri-eval-v3.dtb \
imx6ull-colibri-wifi-eval-v3.dtb \
+ imx6ull-myir-mys-6ulx-nand.dtb \
imx6ull-opos6uldev.dtb \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
new file mode 100644
index 000000000000..43e072671ca4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-myir-mys-6ulx.dtsi"
+
+/ {
+ model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
+ compatible = "myir,imx6ull-mys-6ulx-nand", "myir,imx6ull-mys-6ulx",
+ "fsl,imx6ull";
+};
+
+&gpmi {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
new file mode 100644
index 000000000000..03365a1ca8e6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "MYiR MYS-6ULX Single Board Computer";
+ compatible = "myir,imx6ull-mys-6ulx", "fsl,imx6ull";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_vdd_3v3: regulator-vdd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <®_vdd_5v>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vdd_3v3>;
+ status = "okay";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_vdd_3v3>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ keep-power-in-suspend;
+ vmmc-supply = <®_vdd_3v3>;
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
+};
--
2.26.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v2 2/2] ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
@ 2020-06-01 14:58 ` Parthiban Nallathambi
0 siblings, 0 replies; 8+ messages in thread
From: Parthiban Nallathambi @ 2020-06-01 14:58 UTC (permalink / raw)
To: m.felsch, shawnguo, robh+dt, s.hauer
Cc: devicetree, Parthiban Nallathambi, linux-kernel, linux-imx,
kernel, festevam, linux-arm-kernel
Add support for the MYiR imx6ULL based single board computer
equipped with on board 256MB NAND & RAM. The board also
provides expansion header for expansion board, but this
commit adds only support for SBC.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
---
Notes:
Changelog v2:
- moved regulator under root node
- status property removed
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-myir-mys-6ulx-nand.dts | 19 ++
arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi | 238 ++++++++++++++++++
3 files changed, 258 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd99201397..eab86051d782 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -612,6 +612,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri-eval-v3.dtb \
imx6ull-colibri-wifi-eval-v3.dtb \
+ imx6ull-myir-mys-6ulx-nand.dtb \
imx6ull-opos6uldev.dtb \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
new file mode 100644
index 000000000000..43e072671ca4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-myir-mys-6ulx.dtsi"
+
+/ {
+ model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
+ compatible = "myir,imx6ull-mys-6ulx-nand", "myir,imx6ull-mys-6ulx",
+ "fsl,imx6ull";
+};
+
+&gpmi {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
new file mode 100644
index 000000000000..03365a1ca8e6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "MYiR MYS-6ULX Single Board Computer";
+ compatible = "myir,imx6ull-mys-6ulx", "fsl,imx6ull";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_vdd_3v3: regulator-vdd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <®_vdd_5v>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vdd_3v3>;
+ status = "okay";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_vdd_3v3>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ keep-power-in-suspend;
+ vmmc-supply = <®_vdd_3v3>;
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
+};
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v2 2/2] ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
2020-06-01 14:58 ` Parthiban Nallathambi
@ 2020-06-09 22:45 ` Rob Herring
-1 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2020-06-09 22:45 UTC (permalink / raw)
To: Parthiban Nallathambi
Cc: m.felsch, shawnguo, s.hauer, kernel, festevam, linux-imx,
devicetree, linux-kernel, linux-arm-kernel
On Mon, Jun 01, 2020 at 04:58:57PM +0200, Parthiban Nallathambi wrote:
> Add support for the MYiR imx6ULL based single board computer
> equipped with on board 256MB NAND & RAM. The board also
> provides expansion header for expansion board, but this
> commit adds only support for SBC.
>
> Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
> ---
>
> Notes:
> Changelog v2:
> - moved regulator under root node
> - status property removed
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/imx6ull-myir-mys-6ulx-nand.dts | 19 ++
> arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi | 238 ++++++++++++++++++
> 3 files changed, 258 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e8dd99201397..eab86051d782 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -612,6 +612,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
> imx6ull-14x14-evk.dtb \
> imx6ull-colibri-eval-v3.dtb \
> imx6ull-colibri-wifi-eval-v3.dtb \
> + imx6ull-myir-mys-6ulx-nand.dtb \
> imx6ull-opos6uldev.dtb \
> imx6ull-phytec-segin-ff-rdk-nand.dtb \
> imx6ull-phytec-segin-ff-rdk-emmc.dtb \
> diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> new file mode 100644
> index 000000000000..43e072671ca4
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> @@ -0,0 +1,19 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 Linumiz
> + * Author: Parthiban Nallathambi <parthiban@linumiz.com>
> + */
> +
> +/dts-v1/;
> +#include "imx6ull.dtsi"
> +#include "imx6ull-myir-mys-6ulx.dtsi"
> +
> +/ {
> + model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
> + compatible = "myir,imx6ull-mys-6ulx-nand", "myir,imx6ull-mys-6ulx",
> + "fsl,imx6ull";
Doesn't match the schema which says you have either
"myir,imx6ull-mys-6ulx-nand" or "myir,imx6ull-mys-6ulx".
You ran this against 'make dtbs_check', right?
> +};
> +
> +&gpmi {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
> new file mode 100644
> index 000000000000..03365a1ca8e6
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
If w/o nand is a valid board config, don't you want to build this (i.e.
make it a .dts)?
> @@ -0,0 +1,238 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 Linumiz
> + * Author: Parthiban Nallathambi <parthiban@linumiz.com>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH v2 2/2] ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
@ 2020-06-09 22:45 ` Rob Herring
0 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2020-06-09 22:45 UTC (permalink / raw)
To: Parthiban Nallathambi
Cc: devicetree, shawnguo, s.hauer, m.felsch, linux-kernel, linux-imx,
kernel, festevam, linux-arm-kernel
On Mon, Jun 01, 2020 at 04:58:57PM +0200, Parthiban Nallathambi wrote:
> Add support for the MYiR imx6ULL based single board computer
> equipped with on board 256MB NAND & RAM. The board also
> provides expansion header for expansion board, but this
> commit adds only support for SBC.
>
> Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
> ---
>
> Notes:
> Changelog v2:
> - moved regulator under root node
> - status property removed
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/imx6ull-myir-mys-6ulx-nand.dts | 19 ++
> arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi | 238 ++++++++++++++++++
> 3 files changed, 258 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> create mode 100644 arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e8dd99201397..eab86051d782 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -612,6 +612,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
> imx6ull-14x14-evk.dtb \
> imx6ull-colibri-eval-v3.dtb \
> imx6ull-colibri-wifi-eval-v3.dtb \
> + imx6ull-myir-mys-6ulx-nand.dtb \
> imx6ull-opos6uldev.dtb \
> imx6ull-phytec-segin-ff-rdk-nand.dtb \
> imx6ull-phytec-segin-ff-rdk-emmc.dtb \
> diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> new file mode 100644
> index 000000000000..43e072671ca4
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-nand.dts
> @@ -0,0 +1,19 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 Linumiz
> + * Author: Parthiban Nallathambi <parthiban@linumiz.com>
> + */
> +
> +/dts-v1/;
> +#include "imx6ull.dtsi"
> +#include "imx6ull-myir-mys-6ulx.dtsi"
> +
> +/ {
> + model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
> + compatible = "myir,imx6ull-mys-6ulx-nand", "myir,imx6ull-mys-6ulx",
> + "fsl,imx6ull";
Doesn't match the schema which says you have either
"myir,imx6ull-mys-6ulx-nand" or "myir,imx6ull-mys-6ulx".
You ran this against 'make dtbs_check', right?
> +};
> +
> +&gpmi {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
> new file mode 100644
> index 000000000000..03365a1ca8e6
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
If w/o nand is a valid board config, don't you want to build this (i.e.
make it a .dts)?
> @@ -0,0 +1,238 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 Linumiz
> + * Author: Parthiban Nallathambi <parthiban@linumiz.com>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: fsl: Add MYiR Tech boards
2020-06-01 14:58 ` Parthiban Nallathambi
@ 2020-06-09 22:38 ` Rob Herring
-1 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2020-06-09 22:38 UTC (permalink / raw)
To: Parthiban Nallathambi
Cc: m.felsch, shawnguo, s.hauer, kernel, festevam, linux-imx,
devicetree, linux-kernel, linux-arm-kernel
On Mon, Jun 01, 2020 at 04:58:56PM +0200, Parthiban Nallathambi wrote:
> Add entries for MYiR Tech imx6ULL eval boards.
>
> Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index cd3fbe7e3948..592d73187da4 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -264,6 +264,8 @@ properties:
> - armadeus,imx6ull-opos6uldev # OPOS6UL (i.MX6ULL) SoM on OPOS6ULDev board
> - fsl,imx6ull-14x14-evk # i.MX6 UltraLiteLite 14x14 EVK Board
> - kontron,imx6ull-n6411-som # Kontron N6411 SOM
> + - myir,imx6ull-mys-6ulx # MYiR Tech iMX6ULL Evaluation Board
> + - myir,imx6ull-mys-6ulx-nand # MYiR Tech iMX6ULL Evaluation Board with NAND
Can't you tell there is nand by the presence of a nand nodes?
> - toradex,colibri-imx6ull-eval # Colibri iMX6ULL Module on Colibri Evaluation Board
> - toradex,colibri-imx6ull-wifi-eval # Colibri iMX6ULL Wi-Fi / Bluetooth Module on Colibri Evaluation Board
> - const: fsl,imx6ull
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: fsl: Add MYiR Tech boards
@ 2020-06-09 22:38 ` Rob Herring
0 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2020-06-09 22:38 UTC (permalink / raw)
To: Parthiban Nallathambi
Cc: devicetree, shawnguo, s.hauer, m.felsch, linux-kernel, linux-imx,
kernel, festevam, linux-arm-kernel
On Mon, Jun 01, 2020 at 04:58:56PM +0200, Parthiban Nallathambi wrote:
> Add entries for MYiR Tech imx6ULL eval boards.
>
> Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index cd3fbe7e3948..592d73187da4 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -264,6 +264,8 @@ properties:
> - armadeus,imx6ull-opos6uldev # OPOS6UL (i.MX6ULL) SoM on OPOS6ULDev board
> - fsl,imx6ull-14x14-evk # i.MX6 UltraLiteLite 14x14 EVK Board
> - kontron,imx6ull-n6411-som # Kontron N6411 SOM
> + - myir,imx6ull-mys-6ulx # MYiR Tech iMX6ULL Evaluation Board
> + - myir,imx6ull-mys-6ulx-nand # MYiR Tech iMX6ULL Evaluation Board with NAND
Can't you tell there is nand by the presence of a nand nodes?
> - toradex,colibri-imx6ull-eval # Colibri iMX6ULL Module on Colibri Evaluation Board
> - toradex,colibri-imx6ull-wifi-eval # Colibri iMX6ULL Wi-Fi / Bluetooth Module on Colibri Evaluation Board
> - const: fsl,imx6ull
> --
> 2.26.2
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread