* [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4)
@ 2020-06-18 17:45 Jagan Teki
2020-06-18 17:45 ` [PATCH v3 1/4] spi: kirkwood: Drop nondm code Jagan Teki
` (4 more replies)
0 siblings, 5 replies; 14+ messages in thread
From: Jagan Teki @ 2020-06-18 17:45 UTC (permalink / raw)
To: u-boot
Series of kirkwood boards to switch DM_SPI and drop
which are not DM enabled still.
Any inputs?
Jagan.
Bhargav Shah (1):
spi: kirkwood: Drop nondm code
Jagan Teki (3):
arm: Remove d2net_v2 board
db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH
arm: Remove netspace_v2 board
arch/arm/mach-kirkwood/Kconfig | 8 -
board/LaCie/net2big_v2/Kconfig | 12 -
board/LaCie/net2big_v2/MAINTAINERS | 7 -
board/LaCie/net2big_v2/Makefile | 13 --
board/LaCie/net2big_v2/kwbimage.cfg | 149 -------------
board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------
board/LaCie/net2big_v2/net2big_v2.h | 28 ---
board/LaCie/netspace_v2/Kconfig | 12 -
board/LaCie/netspace_v2/MAINTAINERS | 14 --
board/LaCie/netspace_v2/Makefile | 10 -
board/LaCie/netspace_v2/kwbimage-is2.cfg | 149 -------------
board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 149 -------------
board/LaCie/netspace_v2/kwbimage.cfg | 149 -------------
board/LaCie/netspace_v2/netspace_v2.c | 120 ----------
board/LaCie/netspace_v2/netspace_v2.h | 22 --
configs/d2net_v2_defconfig | 53 -----
configs/db-88f6281-bp-nand_defconfig | 4 +-
configs/inetspace_v2_defconfig | 53 -----
configs/net2big_v2_defconfig | 53 -----
configs/netspace_lite_v2_defconfig | 53 -----
configs/netspace_max_v2_defconfig | 53 -----
configs/netspace_mini_v2_defconfig | 48 ----
configs/netspace_v2_defconfig | 53 -----
drivers/spi/Kconfig | 12 +-
drivers/spi/kirkwood_spi.c | 136 ++----------
include/configs/lacie_kw.h | 152 -------------
scripts/config_whitelist.txt | 1 -
27 files changed, 21 insertions(+), 1749 deletions(-)
delete mode 100644 board/LaCie/net2big_v2/Kconfig
delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
delete mode 100644 board/LaCie/net2big_v2/Makefile
delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
delete mode 100644 board/LaCie/netspace_v2/Kconfig
delete mode 100644 board/LaCie/netspace_v2/MAINTAINERS
delete mode 100644 board/LaCie/netspace_v2/Makefile
delete mode 100644 board/LaCie/netspace_v2/kwbimage-is2.cfg
delete mode 100644 board/LaCie/netspace_v2/kwbimage-ns2l.cfg
delete mode 100644 board/LaCie/netspace_v2/kwbimage.cfg
delete mode 100644 board/LaCie/netspace_v2/netspace_v2.c
delete mode 100644 board/LaCie/netspace_v2/netspace_v2.h
delete mode 100644 configs/d2net_v2_defconfig
delete mode 100644 configs/inetspace_v2_defconfig
delete mode 100644 configs/net2big_v2_defconfig
delete mode 100644 configs/netspace_lite_v2_defconfig
delete mode 100644 configs/netspace_max_v2_defconfig
delete mode 100644 configs/netspace_mini_v2_defconfig
delete mode 100644 configs/netspace_v2_defconfig
delete mode 100644 include/configs/lacie_kw.h
--
2.25.1
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 1/4] spi: kirkwood: Drop nondm code
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
@ 2020-06-18 17:45 ` Jagan Teki
2020-06-18 17:45 ` [PATCH v3 2/4] arm: Remove d2net_v2 board Jagan Teki
` (3 subsequent siblings)
4 siblings, 0 replies; 14+ messages in thread
From: Jagan Teki @ 2020-06-18 17:45 UTC (permalink / raw)
To: u-boot
From: Bhargav Shah <bhargavshah1988@gmail.com>
Drop the nondm code from kirkwood_spi.c since there
is no board or any other code using for it.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- updated commit message
- updated config_whitelist.txt
drivers/spi/Kconfig | 12 ++--
drivers/spi/kirkwood_spi.c | 136 ++++-------------------------------
scripts/config_whitelist.txt | 1 -
3 files changed, 19 insertions(+), 130 deletions(-)
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 09b9cb17d8..0945177efb 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -162,6 +162,12 @@ config ICH_SPI
access the SPI NOR flash on platforms embedding this Intel
ICH IP core.
+config KIRKWOOD_SPI
+ bool "Marvell Kirkwood SPI Driver"
+ help
+ Enable support for SPI on various Marvell SoCs, such as
+ Kirkwood and Armada 375.
+
config MESON_SPIFC
bool "Amlogic Meson SPI Flash Controller driver"
depends on ARCH_MESON
@@ -417,12 +423,6 @@ config SH_QSPI
Enable the Renesas Quad SPI controller driver. This driver can be
used on Renesas SoCs.
-config KIRKWOOD_SPI
- bool "Marvell Kirkwood SPI Driver"
- help
- Enable support for SPI on various Marvell SoCs, such as
- Kirkwood and Armada 375.
-
config MXC_SPI
bool "MXC SPI Driver"
help
diff --git a/drivers/spi/kirkwood_spi.c b/drivers/spi/kirkwood_spi.c
index 3986b06b25..92dc2e13c5 100644
--- a/drivers/spi/kirkwood_spi.c
+++ b/drivers/spi/kirkwood_spi.c
@@ -19,6 +19,19 @@
#endif
#include <asm/arch-mvebu/spi.h>
+struct mvebu_spi_dev {
+ bool is_errata_50mhz_ac;
+};
+
+struct mvebu_spi_platdata {
+ struct kwspi_registers *spireg;
+ bool is_errata_50mhz_ac;
+};
+
+struct mvebu_spi_priv {
+ struct kwspi_registers *spireg;
+};
+
static void _spi_cs_activate(struct kwspi_registers *reg)
{
setbits_le32(®->ctrl, KWSPI_CSN_ACT);
@@ -94,128 +107,6 @@ static int _spi_xfer(struct kwspi_registers *reg, unsigned int bitlen,
return 0;
}
-#ifndef CONFIG_DM_SPI
-
-static struct kwspi_registers *spireg =
- (struct kwspi_registers *)MVEBU_SPI_BASE;
-
-#ifdef CONFIG_ARCH_KIRKWOOD
-static u32 cs_spi_mpp_back[2];
-#endif
-
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
- unsigned int max_hz, unsigned int mode)
-{
- struct spi_slave *slave;
- u32 data;
-#ifdef CONFIG_ARCH_KIRKWOOD
- static const u32 kwspi_mpp_config[2][2] = {
- { MPP0_SPI_SCn, 0 }, /* if cs == 0 */
- { MPP7_SPI_SCn, 0 } /* if cs != 0 */
- };
-#endif
-
- if (!spi_cs_is_valid(bus, cs))
- return NULL;
-
- slave = spi_alloc_slave_base(bus, cs);
- if (!slave)
- return NULL;
-
- writel(KWSPI_SMEMRDY, &spireg->ctrl);
-
- /* calculate spi clock prescaller using max_hz */
- data = ((CONFIG_SYS_TCLK / 2) / max_hz) + 0x10;
- data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
- data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;
-
- /* program spi clock prescaller using max_hz */
- writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
- debug("data = 0x%08x\n", data);
-
- writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause);
- writel(KWSPI_IRQMASK, &spireg->irq_mask);
-
-#ifdef CONFIG_ARCH_KIRKWOOD
- /* program mpp registers to select SPI_CSn */
- kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
-#endif
-
- return slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
-{
-#ifdef CONFIG_ARCH_KIRKWOOD
- kirkwood_mpp_conf(cs_spi_mpp_back, NULL);
-#endif
- free(slave);
-}
-
-__attribute__((weak)) int board_spi_claim_bus(struct spi_slave *slave)
-{
- return 0;
-}
-
-int spi_claim_bus(struct spi_slave *slave)
-{
- return board_spi_claim_bus(slave);
-}
-
-__attribute__((weak)) void board_spi_release_bus(struct spi_slave *slave)
-{
-}
-
-void spi_release_bus(struct spi_slave *slave)
-{
- board_spi_release_bus(slave);
-}
-
-#ifndef CONFIG_SPI_CS_IS_VALID
-/*
- * you can define this function board specific
- * define above CONFIG in board specific config file and
- * provide the function in board specific src file
- */
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && (cs == 0 || cs == 1);
-}
-#endif
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- _spi_cs_activate(spireg);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- _spi_cs_deactivate(spireg);
-}
-
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
- const void *dout, void *din, unsigned long flags)
-{
- return _spi_xfer(spireg, bitlen, dout, din, flags);
-}
-
-#else
-
-/* Here now the DM part */
-
-struct mvebu_spi_dev {
- bool is_errata_50mhz_ac;
-};
-
-struct mvebu_spi_platdata {
- struct kwspi_registers *spireg;
- bool is_errata_50mhz_ac;
-};
-
-struct mvebu_spi_priv {
- struct kwspi_registers *spireg;
-};
-
static int mvebu_spi_set_speed(struct udevice *bus, uint hz)
{
struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
@@ -409,4 +300,3 @@ U_BOOT_DRIVER(mvebu_spi) = {
.priv_auto_alloc_size = sizeof(struct mvebu_spi_priv),
.probe = mvebu_spi_probe,
};
-#endif
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index f6bf6f2474..e6f5bd7e6d 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -1619,7 +1619,6 @@ CONFIG_SPEAR_USBBOOT
CONFIG_SPEAR_USBTTY
CONFIG_SPI_ADDR
CONFIG_SPI_BOOTING
-CONFIG_SPI_CS_IS_VALID
CONFIG_SPI_DATAFLASH_WRITE_VERIFY
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
2020-06-18 17:45 ` [PATCH v3 1/4] spi: kirkwood: Drop nondm code Jagan Teki
@ 2020-06-18 17:45 ` Jagan Teki
2020-06-18 22:02 ` Simon Guinot
2020-06-18 17:45 ` [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH Jagan Teki
` (2 subsequent siblings)
4 siblings, 1 reply; 14+ messages in thread
From: Jagan Teki @ 2020-06-18 17:45 UTC (permalink / raw)
To: u-boot
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- new patch
arch/arm/mach-kirkwood/Kconfig | 4 -
board/LaCie/net2big_v2/Kconfig | 12 --
board/LaCie/net2big_v2/MAINTAINERS | 7 -
board/LaCie/net2big_v2/Makefile | 13 --
board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
board/LaCie/net2big_v2/net2big_v2.h | 28 ---
configs/d2net_v2_defconfig | 53 ------
configs/net2big_v2_defconfig | 53 ------
include/configs/lacie_kw.h | 152 ----------------
10 files changed, 728 deletions(-)
delete mode 100644 board/LaCie/net2big_v2/Kconfig
delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
delete mode 100644 board/LaCie/net2big_v2/Makefile
delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
delete mode 100644 configs/d2net_v2_defconfig
delete mode 100644 configs/net2big_v2_defconfig
delete mode 100644 include/configs/lacie_kw.h
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index ae44cb665e..ad6aef45bf 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
bool "KM Kirkwood Board"
select VENDOR_KM
-config TARGET_NET2BIG_V2
- bool "LaCie 2Big Network v2 NAS Board"
-
config TARGET_NETSPACE_V2
bool "LaCie netspace_v2 Board"
@@ -80,7 +77,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
source "board/d-link/dns325/Kconfig"
source "board/iomega/iconnect/Kconfig"
source "board/keymile/Kconfig"
-source "board/LaCie/net2big_v2/Kconfig"
source "board/LaCie/netspace_v2/Kconfig"
source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
deleted file mode 100644
index ba460dba45..0000000000
--- a/board/LaCie/net2big_v2/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_NET2BIG_V2
-
-config SYS_BOARD
- default "net2big_v2"
-
-config SYS_VENDOR
- default "LaCie"
-
-config SYS_CONFIG_NAME
- default "lacie_kw"
-
-endif
diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
deleted file mode 100644
index 8fec70315f..0000000000
--- a/board/LaCie/net2big_v2/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-NET2BIG_V2 BOARD
-M: Simon Guinot <simon.guinot@sequanux.org>
-S: Maintained
-F: board/LaCie/net2big_v2/
-F: include/configs/lacie_kw.h
-F: configs/d2net_v2_defconfig
-F: configs/net2big_v2_defconfig
diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
deleted file mode 100644
index 3d12b72812..0000000000
--- a/board/LaCie/net2big_v2/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-
-obj-y := net2big_v2.o ../common/common.o
-ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
-obj-y += ../common/cpld-gpio-bus.o
-endif
diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
deleted file mode 100644
index 3897a1197a..0000000000
--- a/board/LaCie/net2big_v2/kwbimage.cfg
+++ /dev/null
@@ -1,149 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000C30 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x38743000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A32 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000CCCC # DDR Address Control
-# bit1-0: 01, Cs0width=x16
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000662 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000044 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
deleted file mode 100644
index dbd8b5755d..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.c
+++ /dev/null
@@ -1,257 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "net2big_v2.h"
-#include "../common/common.h"
-#include "../common/cpld-gpio-bus.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /* GPIO configuration */
- mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
- NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* Request power-off */
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP13_GPIO, /* Rear power switch (on|auto) */
- MPP14_GPIO, /* USB fuse alarm */
- MPP15_GPIO, /* Rear power switch (auto|off) */
- MPP16_GPIO, /* SATA HDD1 power */
- MPP17_GPIO, /* SATA HDD2 power */
- MPP20_SATA1_ACTn,
- MPP21_SATA0_ACTn,
- MPP24_GPIO, /* USB mode select */
- MPP26_GPIO, /* USB device vbus */
- MPP28_GPIO, /* USB enable host vbus */
- MPP29_GPIO, /* CPLD GPIO bus ALE */
- MPP34_GPIO, /* Rear Push button 0=on 1=off */
- MPP35_GPIO, /* Inhibit switch power-off */
- MPP36_GPIO, /* SATA HDD1 presence */
- MPP37_GPIO, /* SATA HDD2 presence */
- MPP40_GPIO, /* eSATA presence */
- MPP44_GPIO, /* CPLD GPIO bus (data 0) */
- MPP45_GPIO, /* CPLD GPIO bus (data 1) */
- MPP46_GPIO, /* CPLD GPIO bus (data 2) */
- MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
- MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
- MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
- 0
- };
-
- kirkwood_mpp_conf(kwmpp_config, NULL);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Machine number */
- gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
-
- /* Boot parameters address */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
-/*
- * Start I2C fan (GMT G762 controller)
- */
-static void init_fan(void)
-{
- u8 data;
-
- i2c_set_bus_num(0);
-
- /* Enable open-loop and PWM modes */
- data = 0x20;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_FAN_CMD1, 1, &data, 1) != 0)
- goto err;
- data = 0;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_SET_CNT, 1, &data, 1) != 0)
- goto err;
- /*
- * RPM to PWM (set_out register) fan speed conversion array:
- * 0 0x00
- * 1500 0x04
- * 2800 0x08
- * 3400 0x0C
- * 3700 0x10
- * 4400 0x20
- * 4700 0x30
- * 4800 0x50
- * 5200 0x80
- * 5400 0xC0
- * 5500 0xFF
- *
- * Start fan at low speed (2800 RPM):
- */
- data = 0x08;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_SET_OUT, 1, &data, 1) != 0)
- goto err;
-
- return;
-err:
- printf("Error: failed to start I2C fan @%02x\n",
- CONFIG_SYS_I2C_G762_ADDR);
-}
-#else
-static void init_fan(void) {}
-#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
-
-#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
-/*
- * CPLD GPIO bus:
- *
- * - address register : bit [0-2] -> GPIO [47-49]
- * - data register : bit [0-2] -> GPIO [44-46]
- * - enable register : GPIO 29
- */
-static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
-static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
-
-static struct cpld_gpio_bus cpld_gpio_bus = {
- .addr = cpld_gpio_bus_addr,
- .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
- .data = cpld_gpio_bus_data,
- .num_data = ARRAY_SIZE(cpld_gpio_bus_data),
- .enable = 29,
-};
-
-/*
- * LEDs configuration:
- *
- * The LEDs are controlled by a CPLD and can be configured through
- * the CPLD GPIO bus.
- *
- * Address register selection:
- *
- * addr | register
- * ----------------------------
- * 0 | front LED
- * 1 | front LED brightness
- * 2 | SATA LED brightness
- * 3 | SATA0 LED
- * 4 | SATA1 LED
- * 5 | SATA2 LED
- * 6 | SATA3 LED
- * 7 | SATA4 LED
- *
- * Data register configuration:
- *
- * data | LED brightness
- * -------------------------------------------------
- * 0 | min (off)
- * - | -
- * 7 | max
- *
- * data | front LED mode
- * -------------------------------------------------
- * 0 | fix off
- * 1 | fix blue on
- * 2 | fix red on
- * 3 | blink blue on=1 sec and blue off=1 sec
- * 4 | blink red on=1 sec and red off=1 sec
- * 5 | blink blue on=2.5 sec and red on=0.5 sec
- * 6 | blink blue on=1 sec and red on=1 sec
- * 7 | blink blue on=0.5 sec and blue off=2.5 sec
- *
- * data | SATA LED mode
- * -------------------------------------------------
- * 0 | fix off
- * 1 | SATA activity blink
- * 2 | fix red on
- * 3 | blink blue on=1 sec and blue off=1 sec
- * 4 | blink red on=1 sec and red off=1 sec
- * 5 | blink blue on=2.5 sec and red on=0.5 sec
- * 6 | blink blue on=1 sec and red on=1 sec
- * 7 | fix blue on
- */
-static void init_leds(void)
-{
- /* Enable the front blue LED */
- cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
-
- /* Configure SATA LEDs to blink in relation with the SATA activity */
- cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
-}
-#else
-static void init_leds(void) {}
-#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
-
-int misc_init_r(void)
-{
- init_fan();
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
- if (!env_get("ethaddr")) {
- uchar mac[6];
- if (lacie_read_mac_address(mac) == 0)
- eth_env_set_enetaddr("ethaddr", mac);
- }
-#endif
- init_leds();
-
- return 0;
-}
-#endif /* CONFIG_MISC_INIT_R */
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
- mv_phy_88e1116_init("egiga0", 8);
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO)
-/* Return GPIO push button status */
-static int
-do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
-}
-
-U_BOOT_CMD(button, 1, 1, do_read_push_button,
- "Return GPIO push button status 0=off 1=on", "");
-#endif
diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
deleted file mode 100644
index d61dd0e998..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#ifndef NET2BIG_V2_H
-#define NET2BIG_V2_H
-
-/* GPIO configuration */
-#define NET2BIG_V2_OE_LOW 0x0600E000
-#define NET2BIG_V2_OE_HIGH 0x00000134
-#define NET2BIG_V2_OE_VAL_LOW 0x10030000
-#define NET2BIG_V2_OE_VAL_HIGH 0x00000000
-
-/* Buttons */
-#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
-
-/* GMT G762 registers (I2C fan controller) */
-#define G762_REG_SET_CNT 0x00
-#define G762_REG_SET_OUT 0x03
-#define G762_REG_FAN_CMD1 0x04
-
-#endif /* NET2BIG_V2_H */
diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
deleted file mode 100644
index fe3c6c4762..0000000000
--- a/configs/d2net_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" D2 v2"
-CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="d2v2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
deleted file mode 100644
index 1389d30900..0000000000
--- a/configs/net2big_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" 2Big v2"
-CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="2big2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
deleted file mode 100644
index 5bb0255a74..0000000000
--- a/include/configs/lacie_kw.h
+++ /dev/null
@@ -1,152 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- */
-
-#ifndef _CONFIG_LACIE_KW_H
-#define _CONFIG_LACIE_KW_H
-
-/*
- * Machine number definition
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_INETSPACE_V2
-#elif defined(CONFIG_NETSPACE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
-#elif defined(CONFIG_NETSPACE_LITE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
-#elif defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
-#elif defined(CONFIG_NETSPACE_MAX_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
-#elif defined(CONFIG_D2NET_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_D2NET_V2
-#elif defined(CONFIG_NET2BIG_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NET2BIG_V2
-#else
-#error "Unknown board"
-#endif
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
-/* SoC name */
-#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_KW88F6192
-#else
-#define CONFIG_KW88F6281
-#endif
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
-#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
-#endif
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-
-/*
- * Enable platform initialisation via misc_init_r() function
- */
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_NETCONSOLE
-#endif
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
- defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
-#define CONFIG_SYS_IDE_MAXBUS 2
-#define CONFIG_SYS_IDE_MAXDEVICE 2
-#else
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
-#endif
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
-#if defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_I2C_G762_ADDR 0x3e
-#endif
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-
-/*
- * File systems support
- */
-
-/*
- * Environment variables configurations
- */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND \
- "dhcp && run netconsole; " \
- "if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "stdin=serial\0" \
- "stdout=serial\0" \
- "stderr=serial\0" \
- "bootfile=uImage\0" \
- "loadaddr=0x800000\0" \
- "autoload=no\0" \
- "netconsole=" \
- "set stdin $stdin,nc; " \
- "set stdout $stdout,nc; " \
- "set stderr $stderr,nc;\0" \
- "diskload=ide reset && " \
- "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
- "usbload=usb start && " \
- "fatload usb 0:1 $loadaddr /boot/$bootfile\0"
-
-#endif /* _CONFIG_LACIE_KW_H */
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
2020-06-18 17:45 ` [PATCH v3 1/4] spi: kirkwood: Drop nondm code Jagan Teki
2020-06-18 17:45 ` [PATCH v3 2/4] arm: Remove d2net_v2 board Jagan Teki
@ 2020-06-18 17:45 ` Jagan Teki
2020-07-08 6:50 ` Jagan Teki
2020-06-18 17:45 ` [PATCH v3 4/4] arm: Remove netspace_v2 board Jagan Teki
2020-06-19 8:31 ` [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Chris Packham
4 siblings, 1 reply; 14+ messages in thread
From: Jagan Teki @ 2020-06-18 17:45 UTC (permalink / raw)
To: u-boot
Enable DM_SPI, DM_SPI_FLASH for db-88f6281-bp-nand board.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- new patch
configs/db-88f6281-bp-nand_defconfig | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/configs/db-88f6281-bp-nand_defconfig b/configs/db-88f6281-bp-nand_defconfig
index f98e462d42..5a580f28b5 100644
--- a/configs/db-88f6281-bp-nand_defconfig
+++ b/configs/db-88f6281-bp-nand_defconfig
@@ -20,7 +20,6 @@ CONFIG_CMD_DM=y
CONFIG_CMD_IDE=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
-CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -43,7 +42,7 @@ CONFIG_DM=y
CONFIG_MVSATA_IDE=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHY_MARVELL=y
CONFIG_DM_ETH=y
@@ -53,6 +52,7 @@ CONFIG_DM_RTC=y
CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_KIRKWOOD_SPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v3 4/4] arm: Remove netspace_v2 board
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
` (2 preceding siblings ...)
2020-06-18 17:45 ` [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH Jagan Teki
@ 2020-06-18 17:45 ` Jagan Teki
2020-06-20 0:26 ` Simon Guinot
2020-06-19 8:31 ` [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Chris Packham
4 siblings, 1 reply; 14+ messages in thread
From: Jagan Teki @ 2020-06-18 17:45 UTC (permalink / raw)
To: u-boot
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Patch-cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- new patch
arch/arm/mach-kirkwood/Kconfig | 4 -
board/LaCie/netspace_v2/Kconfig | 12 --
board/LaCie/netspace_v2/MAINTAINERS | 14 --
board/LaCie/netspace_v2/Makefile | 10 --
board/LaCie/netspace_v2/kwbimage-is2.cfg | 149 ----------------------
board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 149 ----------------------
board/LaCie/netspace_v2/kwbimage.cfg | 149 ----------------------
board/LaCie/netspace_v2/netspace_v2.c | 120 -----------------
board/LaCie/netspace_v2/netspace_v2.h | 22 ----
configs/inetspace_v2_defconfig | 53 --------
configs/netspace_lite_v2_defconfig | 53 --------
configs/netspace_max_v2_defconfig | 53 --------
configs/netspace_mini_v2_defconfig | 48 -------
configs/netspace_v2_defconfig | 53 --------
14 files changed, 889 deletions(-)
delete mode 100644 board/LaCie/netspace_v2/Kconfig
delete mode 100644 board/LaCie/netspace_v2/MAINTAINERS
delete mode 100644 board/LaCie/netspace_v2/Makefile
delete mode 100644 board/LaCie/netspace_v2/kwbimage-is2.cfg
delete mode 100644 board/LaCie/netspace_v2/kwbimage-ns2l.cfg
delete mode 100644 board/LaCie/netspace_v2/kwbimage.cfg
delete mode 100644 board/LaCie/netspace_v2/netspace_v2.c
delete mode 100644 board/LaCie/netspace_v2/netspace_v2.h
delete mode 100644 configs/inetspace_v2_defconfig
delete mode 100644 configs/netspace_lite_v2_defconfig
delete mode 100644 configs/netspace_max_v2_defconfig
delete mode 100644 configs/netspace_mini_v2_defconfig
delete mode 100644 configs/netspace_v2_defconfig
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index ad6aef45bf..899c079773 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
bool "KM Kirkwood Board"
select VENDOR_KM
-config TARGET_NETSPACE_V2
- bool "LaCie netspace_v2 Board"
-
config TARGET_IB62X0
bool "ib62x0 Board"
@@ -77,7 +74,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
source "board/d-link/dns325/Kconfig"
source "board/iomega/iconnect/Kconfig"
source "board/keymile/Kconfig"
-source "board/LaCie/netspace_v2/Kconfig"
source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
source "board/Seagate/goflexhome/Kconfig"
diff --git a/board/LaCie/netspace_v2/Kconfig b/board/LaCie/netspace_v2/Kconfig
deleted file mode 100644
index 930b822dfb..0000000000
--- a/board/LaCie/netspace_v2/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_NETSPACE_V2
-
-config SYS_BOARD
- default "netspace_v2"
-
-config SYS_VENDOR
- default "LaCie"
-
-config SYS_CONFIG_NAME
- default "lacie_kw"
-
-endif
diff --git a/board/LaCie/netspace_v2/MAINTAINERS b/board/LaCie/netspace_v2/MAINTAINERS
deleted file mode 100644
index 55fd50d4eb..0000000000
--- a/board/LaCie/netspace_v2/MAINTAINERS
+++ /dev/null
@@ -1,14 +0,0 @@
-NETSPACE_V2 BOARD
-M: Simon Guinot <simon.guinot@sequanux.org>
-S: Maintained
-F: board/LaCie/netspace_v2/
-F: include/configs/lacie_kw.h
-F: configs/inetspace_v2_defconfig
-F: configs/netspace_max_v2_defconfig
-F: configs/netspace_v2_defconfig
-
-NETSPACE_LITE_V2 BOARD
-#M: -
-S: Maintained
-F: configs/netspace_lite_v2_defconfig
-F: configs/netspace_mini_v2_defconfig
diff --git a/board/LaCie/netspace_v2/Makefile b/board/LaCie/netspace_v2/Makefile
deleted file mode 100644
index a6270bdd4b..0000000000
--- a/board/LaCie/netspace_v2/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-
-obj-y := netspace_v2.o ../common/common.o
diff --git a/board/LaCie/netspace_v2/kwbimage-is2.cfg b/board/LaCie/netspace_v2/kwbimage-is2.cfg
deleted file mode 100644
index 50f584ae70..0000000000
--- a/board/LaCie/netspace_v2/kwbimage-is2.cfg
+++ /dev/null
@@ -1,149 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000618 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x00000008 # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 10, Cs0size=512Mb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000632 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000004 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
deleted file mode 100644
index 092353a06d..0000000000
--- a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
+++ /dev/null
@@ -1,149 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000618 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x34143000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000DDDD # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 10, Cs0size=512Mb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000632 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000004 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/netspace_v2/kwbimage.cfg b/board/LaCie/netspace_v2/kwbimage.cfg
deleted file mode 100644
index 1ed03fa9a9..0000000000
--- a/board/LaCie/netspace_v2/kwbimage.cfg
+++ /dev/null
@@ -1,149 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000618 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000000C # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000632 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000004 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c
deleted file mode 100644
index 011cc563d1..0000000000
--- a/board/LaCie/netspace_v2/netspace_v2.c
+++ /dev/null
@@ -1,120 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <init.h>
-#include <net.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "netspace_v2.h"
-#include "../common/common.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /* Gpio configuration */
- mvebu_config_gpio(NETSPACE_V2_OE_VAL_LOW, NETSPACE_V2_OE_VAL_HIGH,
- NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* Fan speed (bit 1) */
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_GPO, /* Red led */
- MPP14_GPIO, /* USB fuse */
- MPP16_GPIO, /* SATA 0 power */
- MPP17_GPIO, /* SATA 1 power */
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_SATA1_ACTn,
- MPP21_SATA0_ACTn,
- MPP22_GPIO, /* Fan speed (bit 0) */
- MPP23_GPIO, /* Fan power */
- MPP24_GPIO, /* USB mode select */
- MPP25_GPIO, /* Fan rotation fail */
- MPP26_GPIO, /* USB vbus-in detection */
- MPP28_GPIO, /* USB enable vbus-out */
- MPP29_GPIO, /* Blue led (slow register) */
- MPP30_GPIO, /* Blue led (command register) */
- MPP31_GPIO, /* Board power off */
- MPP32_GPIO, /* Button (0 = Released, 1 = Pushed) */
- MPP33_GPIO, /* Fan speed (bit 2) */
- 0
- };
- kirkwood_mpp_conf(kwmpp_config, NULL);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Machine number */
- gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
-
- /* Boot parameters address */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-int misc_init_r(void)
-{
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
- if (!env_get("ethaddr")) {
- uchar mac[6];
- if (lacie_read_mac_address(mac) == 0)
- eth_env_set_enetaddr("ethaddr", mac);
- }
-#endif
- return 0;
-}
-#endif
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
-#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
- mv_phy_88e1318_init("egiga0", 0);
-#else
- mv_phy_88e1116_init("egiga0", 8);
-#endif
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO)
-/* Return GPIO button status */
-static int
-do_read_button(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- return kw_gpio_get_value(NETSPACE_V2_GPIO_BUTTON);
-}
-
-U_BOOT_CMD(button, 1, 1, do_read_button,
- "Return GPIO button status 0=off 1=on", "");
-#endif
diff --git a/board/LaCie/netspace_v2/netspace_v2.h b/board/LaCie/netspace_v2/netspace_v2.h
deleted file mode 100644
index 2c930171ea..0000000000
--- a/board/LaCie/netspace_v2/netspace_v2.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#ifndef NETSPACE_V2_H
-#define NETSPACE_V2_H
-
-/* GPIO configuration */
-#define NETSPACE_V2_OE_LOW 0x06004000
-#define NETSPACE_V2_OE_HIGH 0x00000031
-#define NETSPACE_V2_OE_VAL_LOW 0x10030000
-#define NETSPACE_V2_OE_VAL_HIGH 0x00000000
-
-#define NETSPACE_V2_GPIO_BUTTON 32
-
-#endif /* NETSPACE_V2_H */
diff --git a/configs/inetspace_v2_defconfig b/configs/inetspace_v2_defconfig
deleted file mode 100644
index 6144eb5fad..0000000000
--- a/configs/inetspace_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NETSPACE_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" IS v2"
-CONFIG_SYS_EXTRA_OPTIONS="INETSPACE_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="ns2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-is2"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/netspace_lite_v2_defconfig b/configs/netspace_lite_v2_defconfig
deleted file mode 100644
index c744d2c58e..0000000000
--- a/configs/netspace_lite_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NETSPACE_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" NS v2 Lite"
-CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_LITE_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="ns2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2lite"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/netspace_max_v2_defconfig b/configs/netspace_max_v2_defconfig
deleted file mode 100644
index 8602729fcb..0000000000
--- a/configs/netspace_max_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NETSPACE_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" NS Max v2"
-CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MAX_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="ns2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2max"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/netspace_mini_v2_defconfig b/configs/netspace_mini_v2_defconfig
deleted file mode 100644
index ba9301de4d..0000000000
--- a/configs/netspace_mini_v2_defconfig
+++ /dev/null
@@ -1,48 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NETSPACE_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" NS v2 Mini"
-CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MINI_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="ns2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2mini"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
diff --git a/configs/netspace_v2_defconfig b/configs/netspace_v2_defconfig
deleted file mode 100644
index 6ba1ef423e..0000000000
--- a/configs/netspace_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NETSPACE_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" NS v2"
-CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="ns2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-18 17:45 ` [PATCH v3 2/4] arm: Remove d2net_v2 board Jagan Teki
@ 2020-06-18 22:02 ` Simon Guinot
2020-06-18 22:25 ` Tom Rini
0 siblings, 1 reply; 14+ messages in thread
From: Simon Guinot @ 2020-06-18 22:02 UTC (permalink / raw)
To: u-boot
On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
Hi Jagan,
> This board has not been converted to CONFIG_DM by the deadline.
Is that possible to negociate a new deadline ?
Thanks in advance.
Simon
>
> Remove it.
>
> Cc: Simon Guinot <simon.guinot@sequanux.org>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> Changes for v3:
> - new patch
>
> arch/arm/mach-kirkwood/Kconfig | 4 -
> board/LaCie/net2big_v2/Kconfig | 12 --
> board/LaCie/net2big_v2/MAINTAINERS | 7 -
> board/LaCie/net2big_v2/Makefile | 13 --
> board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
> board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
> board/LaCie/net2big_v2/net2big_v2.h | 28 ---
> configs/d2net_v2_defconfig | 53 ------
> configs/net2big_v2_defconfig | 53 ------
> include/configs/lacie_kw.h | 152 ----------------
> 10 files changed, 728 deletions(-)
> delete mode 100644 board/LaCie/net2big_v2/Kconfig
> delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
> delete mode 100644 board/LaCie/net2big_v2/Makefile
> delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
> delete mode 100644 configs/d2net_v2_defconfig
> delete mode 100644 configs/net2big_v2_defconfig
> delete mode 100644 include/configs/lacie_kw.h
>
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ae44cb665e..ad6aef45bf 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
> bool "KM Kirkwood Board"
> select VENDOR_KM
>
> -config TARGET_NET2BIG_V2
> - bool "LaCie 2Big Network v2 NAS Board"
> -
> config TARGET_NETSPACE_V2
> bool "LaCie netspace_v2 Board"
>
> @@ -80,7 +77,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
> source "board/d-link/dns325/Kconfig"
> source "board/iomega/iconnect/Kconfig"
> source "board/keymile/Kconfig"
> -source "board/LaCie/net2big_v2/Kconfig"
> source "board/LaCie/netspace_v2/Kconfig"
> source "board/raidsonic/ib62x0/Kconfig"
> source "board/Seagate/dockstar/Kconfig"
> diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
> deleted file mode 100644
> index ba460dba45..0000000000
> --- a/board/LaCie/net2big_v2/Kconfig
> +++ /dev/null
> @@ -1,12 +0,0 @@
> -if TARGET_NET2BIG_V2
> -
> -config SYS_BOARD
> - default "net2big_v2"
> -
> -config SYS_VENDOR
> - default "LaCie"
> -
> -config SYS_CONFIG_NAME
> - default "lacie_kw"
> -
> -endif
> diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
> deleted file mode 100644
> index 8fec70315f..0000000000
> --- a/board/LaCie/net2big_v2/MAINTAINERS
> +++ /dev/null
> @@ -1,7 +0,0 @@
> -NET2BIG_V2 BOARD
> -M: Simon Guinot <simon.guinot@sequanux.org>
> -S: Maintained
> -F: board/LaCie/net2big_v2/
> -F: include/configs/lacie_kw.h
> -F: configs/d2net_v2_defconfig
> -F: configs/net2big_v2_defconfig
> diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
> deleted file mode 100644
> index 3d12b72812..0000000000
> --- a/board/LaCie/net2big_v2/Makefile
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -
> -obj-y := net2big_v2.o ../common/common.o
> -ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
> -obj-y += ../common/cpld-gpio-bus.o
> -endif
> diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
> deleted file mode 100644
> index 3897a1197a..0000000000
> --- a/board/LaCie/net2big_v2/kwbimage.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM spi # Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000C30 # DDR Configuration register
> -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x38743000 # DDR Controller Control Low
> -# bit 4: 0=addr/cmd in smame cycle
> -# bit 5: 0=clk is driven during self refresh, we don't care for APX
> -# bit 6: 0=use recommended falling edge of clk for addr/cmd
> -# bit14: 0=input buffer always powered up
> -# bit18: 1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31: 0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
> -# bit7-4: TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20: TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A32 # DDR Timing (High)
> -# bit6-0: TRFC
> -# bit8-7: TR2R
> -# bit10-9: TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x0000CCCC # DDR Address Control
> -# bit1-0: 01, Cs0width=x16
> -# bit3-2: 11, Cs0size=1Gb
> -# bit5-4: 00, Cs2width=nonexistent
> -# bit7-6: 00, Cs1size =nonexistent
> -# bit9-8: 00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16: 0, Cs0AddrSel
> -# bit17: 0, Cs1AddrSel
> -# bit18: 0, Cs2AddrSel
> -# bit19: 0, Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> -# bit0: 0, OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000 # DDR Operation
> -# bit3-0: 0x0, DDR cmd
> -# bit31-4: 0 required
> -
> -DATA 0xFFD0141C 0x00000662 # DDR Mode
> -# bit2-0: 2, BurstLen=2 required
> -# bit3: 0, BurstType=0 required
> -# bit6-4: 4, CL=5
> -# bit7: 0, TestMode=0 normal
> -# bit8: 0, DLL reset=0 normal
> -# bit11-9: 6, auto-precharge write recovery ????????????
> -# bit12: 0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000044 # DDR Extended Mode
> -# bit0: 0, DDR DLL enabled
> -# bit1: 1, DDR drive strenght reduced
> -# bit2: 1, DDR ODT control lsd enabled
> -# bit5-3: 000, required
> -# bit6: 1, DDR ODT control msb, enabled
> -# bit9-7: 000, required
> -# bit10: 0, differential DQS enabled
> -# bit11: 0, required
> -# bit12: 0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
> -# bit2-0: 111, required
> -# bit3 : 1 , MBUS Burst Chop disabled
> -# bit6-4: 111, required
> -# bit7 : 1 , D2P Latency enabled
> -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9 : 0 , no half clock cycle addition to dataout
> -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0 required
> -
> -DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
> -# bit0: 1, Window enabled
> -# bit1: 0, Write Protect disabled
> -# bit3-2: 00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
> -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2: 01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
> -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
> deleted file mode 100644
> index dbd8b5755d..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.c
> +++ /dev/null
> @@ -1,257 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> - */
> -
> -#include <common.h>
> -#include <command.h>
> -#include <env.h>
> -#include <i2c.h>
> -#include <init.h>
> -#include <net.h>
> -#include <asm/mach-types.h>
> -#include <asm/arch/cpu.h>
> -#include <asm/arch/soc.h>
> -#include <asm/arch/mpp.h>
> -#include <asm/arch/gpio.h>
> -
> -#include "net2big_v2.h"
> -#include "../common/common.h"
> -#include "../common/cpld-gpio-bus.h"
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -int board_early_init_f(void)
> -{
> - /* GPIO configuration */
> - mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
> - NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
> -
> - /* Multi-Purpose Pins Functionality configuration */
> - static const u32 kwmpp_config[] = {
> - MPP0_SPI_SCn,
> - MPP1_SPI_MOSI,
> - MPP2_SPI_SCK,
> - MPP3_SPI_MISO,
> - MPP6_SYSRST_OUTn,
> - MPP7_GPO, /* Request power-off */
> - MPP8_TW_SDA,
> - MPP9_TW_SCK,
> - MPP10_UART0_TXD,
> - MPP11_UART0_RXD,
> - MPP13_GPIO, /* Rear power switch (on|auto) */
> - MPP14_GPIO, /* USB fuse alarm */
> - MPP15_GPIO, /* Rear power switch (auto|off) */
> - MPP16_GPIO, /* SATA HDD1 power */
> - MPP17_GPIO, /* SATA HDD2 power */
> - MPP20_SATA1_ACTn,
> - MPP21_SATA0_ACTn,
> - MPP24_GPIO, /* USB mode select */
> - MPP26_GPIO, /* USB device vbus */
> - MPP28_GPIO, /* USB enable host vbus */
> - MPP29_GPIO, /* CPLD GPIO bus ALE */
> - MPP34_GPIO, /* Rear Push button 0=on 1=off */
> - MPP35_GPIO, /* Inhibit switch power-off */
> - MPP36_GPIO, /* SATA HDD1 presence */
> - MPP37_GPIO, /* SATA HDD2 presence */
> - MPP40_GPIO, /* eSATA presence */
> - MPP44_GPIO, /* CPLD GPIO bus (data 0) */
> - MPP45_GPIO, /* CPLD GPIO bus (data 1) */
> - MPP46_GPIO, /* CPLD GPIO bus (data 2) */
> - MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
> - MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
> - MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
> - 0
> - };
> -
> - kirkwood_mpp_conf(kwmpp_config, NULL);
> -
> - return 0;
> -}
> -
> -int board_init(void)
> -{
> - /* Machine number */
> - gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
> -
> - /* Boot parameters address */
> - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> -
> - return 0;
> -}
> -
> -#if defined(CONFIG_MISC_INIT_R)
> -
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
> -/*
> - * Start I2C fan (GMT G762 controller)
> - */
> -static void init_fan(void)
> -{
> - u8 data;
> -
> - i2c_set_bus_num(0);
> -
> - /* Enable open-loop and PWM modes */
> - data = 0x20;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_FAN_CMD1, 1, &data, 1) != 0)
> - goto err;
> - data = 0;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_SET_CNT, 1, &data, 1) != 0)
> - goto err;
> - /*
> - * RPM to PWM (set_out register) fan speed conversion array:
> - * 0 0x00
> - * 1500 0x04
> - * 2800 0x08
> - * 3400 0x0C
> - * 3700 0x10
> - * 4400 0x20
> - * 4700 0x30
> - * 4800 0x50
> - * 5200 0x80
> - * 5400 0xC0
> - * 5500 0xFF
> - *
> - * Start fan at low speed (2800 RPM):
> - */
> - data = 0x08;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_SET_OUT, 1, &data, 1) != 0)
> - goto err;
> -
> - return;
> -err:
> - printf("Error: failed to start I2C fan @%02x\n",
> - CONFIG_SYS_I2C_G762_ADDR);
> -}
> -#else
> -static void init_fan(void) {}
> -#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
> -
> -#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
> -/*
> - * CPLD GPIO bus:
> - *
> - * - address register : bit [0-2] -> GPIO [47-49]
> - * - data register : bit [0-2] -> GPIO [44-46]
> - * - enable register : GPIO 29
> - */
> -static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
> -static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
> -
> -static struct cpld_gpio_bus cpld_gpio_bus = {
> - .addr = cpld_gpio_bus_addr,
> - .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
> - .data = cpld_gpio_bus_data,
> - .num_data = ARRAY_SIZE(cpld_gpio_bus_data),
> - .enable = 29,
> -};
> -
> -/*
> - * LEDs configuration:
> - *
> - * The LEDs are controlled by a CPLD and can be configured through
> - * the CPLD GPIO bus.
> - *
> - * Address register selection:
> - *
> - * addr | register
> - * ----------------------------
> - * 0 | front LED
> - * 1 | front LED brightness
> - * 2 | SATA LED brightness
> - * 3 | SATA0 LED
> - * 4 | SATA1 LED
> - * 5 | SATA2 LED
> - * 6 | SATA3 LED
> - * 7 | SATA4 LED
> - *
> - * Data register configuration:
> - *
> - * data | LED brightness
> - * -------------------------------------------------
> - * 0 | min (off)
> - * - | -
> - * 7 | max
> - *
> - * data | front LED mode
> - * -------------------------------------------------
> - * 0 | fix off
> - * 1 | fix blue on
> - * 2 | fix red on
> - * 3 | blink blue on=1 sec and blue off=1 sec
> - * 4 | blink red on=1 sec and red off=1 sec
> - * 5 | blink blue on=2.5 sec and red on=0.5 sec
> - * 6 | blink blue on=1 sec and red on=1 sec
> - * 7 | blink blue on=0.5 sec and blue off=2.5 sec
> - *
> - * data | SATA LED mode
> - * -------------------------------------------------
> - * 0 | fix off
> - * 1 | SATA activity blink
> - * 2 | fix red on
> - * 3 | blink blue on=1 sec and blue off=1 sec
> - * 4 | blink red on=1 sec and red off=1 sec
> - * 5 | blink blue on=2.5 sec and red on=0.5 sec
> - * 6 | blink blue on=1 sec and red on=1 sec
> - * 7 | fix blue on
> - */
> -static void init_leds(void)
> -{
> - /* Enable the front blue LED */
> - cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
> -
> - /* Configure SATA LEDs to blink in relation with the SATA activity */
> - cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
> -}
> -#else
> -static void init_leds(void) {}
> -#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
> -
> -int misc_init_r(void)
> -{
> - init_fan();
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
> - if (!env_get("ethaddr")) {
> - uchar mac[6];
> - if (lacie_read_mac_address(mac) == 0)
> - eth_env_set_enetaddr("ethaddr", mac);
> - }
> -#endif
> - init_leds();
> -
> - return 0;
> -}
> -#endif /* CONFIG_MISC_INIT_R */
> -
> -#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
> -/* Configure and initialize PHY */
> -void reset_phy(void)
> -{
> - mv_phy_88e1116_init("egiga0", 8);
> -}
> -#endif
> -
> -#if defined(CONFIG_KIRKWOOD_GPIO)
> -/* Return GPIO push button status */
> -static int
> -do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
> - char *const argv[])
> -{
> - return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
> -}
> -
> -U_BOOT_CMD(button, 1, 1, do_read_push_button,
> - "Return GPIO push button status 0=off 1=on", "");
> -#endif
> diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
> deleted file mode 100644
> index d61dd0e998..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.h
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> - */
> -
> -#ifndef NET2BIG_V2_H
> -#define NET2BIG_V2_H
> -
> -/* GPIO configuration */
> -#define NET2BIG_V2_OE_LOW 0x0600E000
> -#define NET2BIG_V2_OE_HIGH 0x00000134
> -#define NET2BIG_V2_OE_VAL_LOW 0x10030000
> -#define NET2BIG_V2_OE_VAL_HIGH 0x00000000
> -
> -/* Buttons */
> -#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
> -
> -/* GMT G762 registers (I2C fan controller) */
> -#define G762_REG_SET_CNT 0x00
> -#define G762_REG_SET_OUT 0x03
> -#define G762_REG_FAN_CMD1 0x04
> -
> -#endif /* NET2BIG_V2_H */
> diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
> deleted file mode 100644
> index fe3c6c4762..0000000000
> --- a/configs/d2net_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" D2 v2"
> -CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="d2v2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
> deleted file mode 100644
> index 1389d30900..0000000000
> --- a/configs/net2big_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" 2Big v2"
> -CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="2big2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
> deleted file mode 100644
> index 5bb0255a74..0000000000
> --- a/include/configs/lacie_kw.h
> +++ /dev/null
> @@ -1,152 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> - */
> -
> -#ifndef _CONFIG_LACIE_KW_H
> -#define _CONFIG_LACIE_KW_H
> -
> -/*
> - * Machine number definition
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_INETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_LITE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
> -#elif defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
> -#elif defined(CONFIG_NETSPACE_MAX_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
> -#elif defined(CONFIG_D2NET_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_D2NET_V2
> -#elif defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NET2BIG_V2
> -#else
> -#error "Unknown board"
> -#endif
> -
> -/*
> - * High Level Configuration Options (easy to change)
> - */
> -#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
> -/* SoC name */
> -#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_KW88F6192
> -#else
> -#define CONFIG_KW88F6281
> -#endif
> -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
> -
> -/*
> - * Core clock definition
> - */
> -#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
> -
> -/*
> - * SDRAM configuration
> - */
> -
> -/*
> - * Different SDRAM configuration and size for some of the boards derived
> - * from the Network Space v2
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
> -#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
> -#endif
> -
> -/*
> - * mv-common.h should be defined after CMD configs since it used them
> - * to enable certain macros
> - */
> -#include "mv-common.h"
> -
> -/* Remove or override few declarations from mv-common.h */
> -#undef CONFIG_SYS_IDE_MAXBUS
> -#undef CONFIG_SYS_IDE_MAXDEVICE
> -
> -/*
> - * Enable platform initialisation via misc_init_r() function
> - */
> -
> -/*
> - * Ethernet Driver configuration
> - */
> -#ifdef CONFIG_CMD_NET
> -#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
> -#define CONFIG_NETCONSOLE
> -#endif
> -
> -/*
> - * SATA Driver configuration
> - */
> -#ifdef CONFIG_MVSATA_IDE
> -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
> -#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
> - defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
> -#define CONFIG_SYS_IDE_MAXBUS 2
> -#define CONFIG_SYS_IDE_MAXDEVICE 2
> -#else
> -#define CONFIG_SYS_IDE_MAXBUS 1
> -#define CONFIG_SYS_IDE_MAXDEVICE 1
> -#endif
> -#endif /* CONFIG_MVSATA_IDE */
> -
> -/*
> - * Enable GPI0 support
> - */
> -#define CONFIG_KIRKWOOD_GPIO
> -
> -/*
> - * Enable I2C support
> - */
> -#ifdef CONFIG_CMD_I2C
> -/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
> -#if defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_I2C_G762_ADDR 0x3e
> -#endif
> -#endif /* CONFIG_CMD_I2C */
> -
> -/*
> - * Partition support
> - */
> -
> -/*
> - * File systems support
> - */
> -
> -/*
> - * Environment variables configurations
> - */
> -
> -/*
> - * Default environment variables
> - */
> -#define CONFIG_BOOTCOMMAND \
> - "dhcp && run netconsole; " \
> - "if run usbload || run diskload; then bootm; fi"
> -
> -#define CONFIG_EXTRA_ENV_SETTINGS \
> - "stdin=serial\0" \
> - "stdout=serial\0" \
> - "stderr=serial\0" \
> - "bootfile=uImage\0" \
> - "loadaddr=0x800000\0" \
> - "autoload=no\0" \
> - "netconsole=" \
> - "set stdin $stdin,nc; " \
> - "set stdout $stdout,nc; " \
> - "set stderr $stderr,nc;\0" \
> - "diskload=ide reset && " \
> - "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
> - "usbload=usb start && " \
> - "fatload usb 0:1 $loadaddr /boot/$bootfile\0"
> -
> -#endif /* _CONFIG_LACIE_KW_H */
> --
> 2.25.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200619/7f85313c/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-18 22:02 ` Simon Guinot
@ 2020-06-18 22:25 ` Tom Rini
2020-06-20 0:24 ` Simon Guinot
0 siblings, 1 reply; 14+ messages in thread
From: Tom Rini @ 2020-06-18 22:25 UTC (permalink / raw)
To: u-boot
On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> Hi Jagan,
>
> > This board has not been converted to CONFIG_DM by the deadline.
>
> Is that possible to negociate a new deadline ?
Well, when will you be able to spend some time bringing the platform up
to current standards? Doing a quick build for net2big_v2 I see:
+(net2big_v2) ===================== WARNING ======================
+(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
+(net2big_v2) compulsory starting with the v2020.01 release.
+(net2big_v2) Failure to update may result in board removal.
+(net2big_v2) See doc/driver-model/migration.rst for more info.
+(net2big_v2) ====================================================
+(net2big_v2) This board does not use CONFIG_DM_USB. Please update
+(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
+(net2big_v2) Failure to update by the deadline may result in board removal.
+(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
+(net2big_v2) ported to driver-model (DM) yet. Please update the storage
+(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
+(net2big_v2) release.
+(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
+(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
+(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
+(net2big_v2) for Ethernet drivers). Please update the board to use
+(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
+(net2big_v2) update by the deadline may result in board removal.
So there's a lot of stuff that needs updating. Conversion to CONFIG_DM
is what you'll need to then convert SPI, ETH and USB to use DM and the
IDE driver also needs attention and conversion. Thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200618/9bffc35d/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4)
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
` (3 preceding siblings ...)
2020-06-18 17:45 ` [PATCH v3 4/4] arm: Remove netspace_v2 board Jagan Teki
@ 2020-06-19 8:31 ` Chris Packham
2020-06-25 1:05 ` Chris Packham
4 siblings, 1 reply; 14+ messages in thread
From: Chris Packham @ 2020-06-19 8:31 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On Fri, 19 Jun 2020, 5:45 AM Jagan Teki, <jagan@amarulasolutions.com> wrote:
> Series of kirkwood boards to switch DM_SPI and drop
> which are not DM enabled still.
>
> Any inputs?
> Jagan.
>
I had a quick glance over the series and it looks good to me.
I'm fortunate enough to be able to get into the office so I'll try and give
this a spin on the kirkwood board I have on Monday.
Bhargav Shah (1):
> spi: kirkwood: Drop nondm code
>
> Jagan Teki (3):
> arm: Remove d2net_v2 board
> db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH
> arm: Remove netspace_v2 board
>
> arch/arm/mach-kirkwood/Kconfig | 8 -
> board/LaCie/net2big_v2/Kconfig | 12 -
> board/LaCie/net2big_v2/MAINTAINERS | 7 -
> board/LaCie/net2big_v2/Makefile | 13 --
> board/LaCie/net2big_v2/kwbimage.cfg | 149 -------------
> board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------
> board/LaCie/net2big_v2/net2big_v2.h | 28 ---
> board/LaCie/netspace_v2/Kconfig | 12 -
> board/LaCie/netspace_v2/MAINTAINERS | 14 --
> board/LaCie/netspace_v2/Makefile | 10 -
> board/LaCie/netspace_v2/kwbimage-is2.cfg | 149 -------------
> board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 149 -------------
> board/LaCie/netspace_v2/kwbimage.cfg | 149 -------------
> board/LaCie/netspace_v2/netspace_v2.c | 120 ----------
> board/LaCie/netspace_v2/netspace_v2.h | 22 --
> configs/d2net_v2_defconfig | 53 -----
> configs/db-88f6281-bp-nand_defconfig | 4 +-
> configs/inetspace_v2_defconfig | 53 -----
> configs/net2big_v2_defconfig | 53 -----
> configs/netspace_lite_v2_defconfig | 53 -----
> configs/netspace_max_v2_defconfig | 53 -----
> configs/netspace_mini_v2_defconfig | 48 ----
> configs/netspace_v2_defconfig | 53 -----
> drivers/spi/Kconfig | 12 +-
> drivers/spi/kirkwood_spi.c | 136 ++----------
> include/configs/lacie_kw.h | 152 -------------
> scripts/config_whitelist.txt | 1 -
> 27 files changed, 21 insertions(+), 1749 deletions(-)
> delete mode 100644 board/LaCie/net2big_v2/Kconfig
> delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
> delete mode 100644 board/LaCie/net2big_v2/Makefile
> delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
> delete mode 100644 board/LaCie/netspace_v2/Kconfig
> delete mode 100644 board/LaCie/netspace_v2/MAINTAINERS
> delete mode 100644 board/LaCie/netspace_v2/Makefile
> delete mode 100644 board/LaCie/netspace_v2/kwbimage-is2.cfg
> delete mode 100644 board/LaCie/netspace_v2/kwbimage-ns2l.cfg
> delete mode 100644 board/LaCie/netspace_v2/kwbimage.cfg
> delete mode 100644 board/LaCie/netspace_v2/netspace_v2.c
> delete mode 100644 board/LaCie/netspace_v2/netspace_v2.h
> delete mode 100644 configs/d2net_v2_defconfig
> delete mode 100644 configs/inetspace_v2_defconfig
> delete mode 100644 configs/net2big_v2_defconfig
> delete mode 100644 configs/netspace_lite_v2_defconfig
> delete mode 100644 configs/netspace_max_v2_defconfig
> delete mode 100644 configs/netspace_mini_v2_defconfig
> delete mode 100644 configs/netspace_v2_defconfig
> delete mode 100644 include/configs/lacie_kw.h
>
> --
> 2.25.1
>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-18 22:25 ` Tom Rini
@ 2020-06-20 0:24 ` Simon Guinot
2020-06-20 0:25 ` Tom Rini
0 siblings, 1 reply; 14+ messages in thread
From: Simon Guinot @ 2020-06-20 0:24 UTC (permalink / raw)
To: u-boot
On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > Hi Jagan,
> >
> > > This board has not been converted to CONFIG_DM by the deadline.
> >
> > Is that possible to negociate a new deadline ?
>
> Well, when will you be able to spend some time bringing the platform up
> to current standards? Doing a quick build for net2big_v2 I see:
> +(net2big_v2) ===================== WARNING ======================
> +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> +(net2big_v2) compulsory starting with the v2020.01 release.
> +(net2big_v2) Failure to update may result in board removal.
> +(net2big_v2) See doc/driver-model/migration.rst for more info.
> +(net2big_v2) ====================================================
> +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> +(net2big_v2) Failure to update by the deadline may result in board removal.
> +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> +(net2big_v2) release.
> +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> +(net2big_v2) for Ethernet drivers). Please update the board to use
> +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> +(net2big_v2) update by the deadline may result in board removal.
>
> So there's a lot of stuff that needs updating. Conversion to CONFIG_DM
> is what you'll need to then convert SPI, ETH and USB to use DM and the
> IDE driver also needs attention and conversion. Thanks!
Hi Tom,
I am working on it. But so far it is not going very well and the whole
thing is turning into a debug session.
But I'll do my best and whatever the result will be, I'll send you an
update by the end of the next week.
Is this acceptable to you ?
Thanks.
Simon
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200620/3129d168/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-20 0:24 ` Simon Guinot
@ 2020-06-20 0:25 ` Tom Rini
2020-06-24 22:42 ` Simon Guinot
0 siblings, 1 reply; 14+ messages in thread
From: Tom Rini @ 2020-06-20 0:25 UTC (permalink / raw)
To: u-boot
On Sat, Jun 20, 2020 at 02:24:47AM +0200, Simon Guinot wrote:
> On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> > On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > > Hi Jagan,
> > >
> > > > This board has not been converted to CONFIG_DM by the deadline.
> > >
> > > Is that possible to negociate a new deadline ?
> >
> > Well, when will you be able to spend some time bringing the platform up
> > to current standards? Doing a quick build for net2big_v2 I see:
> > +(net2big_v2) ===================== WARNING ======================
> > +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> > +(net2big_v2) compulsory starting with the v2020.01 release.
> > +(net2big_v2) Failure to update may result in board removal.
> > +(net2big_v2) See doc/driver-model/migration.rst for more info.
> > +(net2big_v2) ====================================================
> > +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> > +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> > +(net2big_v2) Failure to update by the deadline may result in board removal.
> > +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> > +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> > +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> > +(net2big_v2) release.
> > +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> > +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> > +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> > +(net2big_v2) for Ethernet drivers). Please update the board to use
> > +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> > +(net2big_v2) update by the deadline may result in board removal.
> >
> > So there's a lot of stuff that needs updating. Conversion to CONFIG_DM
> > is what you'll need to then convert SPI, ETH and USB to use DM and the
> > IDE driver also needs attention and conversion. Thanks!
>
> Hi Tom,
>
> I am working on it. But so far it is not going very well and the whole
> thing is turning into a debug session.
>
> But I'll do my best and whatever the result will be, I'll send you an
> update by the end of the next week.
>
> Is this acceptable to you ?
Yes, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200619/bbd04a2a/attachment-0001.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 4/4] arm: Remove netspace_v2 board
2020-06-18 17:45 ` [PATCH v3 4/4] arm: Remove netspace_v2 board Jagan Teki
@ 2020-06-20 0:26 ` Simon Guinot
0 siblings, 0 replies; 14+ messages in thread
From: Simon Guinot @ 2020-06-20 0:26 UTC (permalink / raw)
To: u-boot
On Thu, Jun 18, 2020 at 11:15:16PM +0530, Jagan Teki wrote:
> This board has not been converted to CONFIG_DM by the deadline.
I am working at converting this board too, along with net2big_v2.
Simon
>
> Remove it.
>
> Patch-cc: Simon Guinot <simon.guinot@sequanux.org>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> Changes for v3:
> - new patch
>
> arch/arm/mach-kirkwood/Kconfig | 4 -
> board/LaCie/netspace_v2/Kconfig | 12 --
> board/LaCie/netspace_v2/MAINTAINERS | 14 --
> board/LaCie/netspace_v2/Makefile | 10 --
> board/LaCie/netspace_v2/kwbimage-is2.cfg | 149 ----------------------
> board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 149 ----------------------
> board/LaCie/netspace_v2/kwbimage.cfg | 149 ----------------------
> board/LaCie/netspace_v2/netspace_v2.c | 120 -----------------
> board/LaCie/netspace_v2/netspace_v2.h | 22 ----
> configs/inetspace_v2_defconfig | 53 --------
> configs/netspace_lite_v2_defconfig | 53 --------
> configs/netspace_max_v2_defconfig | 53 --------
> configs/netspace_mini_v2_defconfig | 48 -------
> configs/netspace_v2_defconfig | 53 --------
> 14 files changed, 889 deletions(-)
> delete mode 100644 board/LaCie/netspace_v2/Kconfig
> delete mode 100644 board/LaCie/netspace_v2/MAINTAINERS
> delete mode 100644 board/LaCie/netspace_v2/Makefile
> delete mode 100644 board/LaCie/netspace_v2/kwbimage-is2.cfg
> delete mode 100644 board/LaCie/netspace_v2/kwbimage-ns2l.cfg
> delete mode 100644 board/LaCie/netspace_v2/kwbimage.cfg
> delete mode 100644 board/LaCie/netspace_v2/netspace_v2.c
> delete mode 100644 board/LaCie/netspace_v2/netspace_v2.h
> delete mode 100644 configs/inetspace_v2_defconfig
> delete mode 100644 configs/netspace_lite_v2_defconfig
> delete mode 100644 configs/netspace_max_v2_defconfig
> delete mode 100644 configs/netspace_mini_v2_defconfig
> delete mode 100644 configs/netspace_v2_defconfig
>
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ad6aef45bf..899c079773 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
> bool "KM Kirkwood Board"
> select VENDOR_KM
>
> -config TARGET_NETSPACE_V2
> - bool "LaCie netspace_v2 Board"
> -
> config TARGET_IB62X0
> bool "ib62x0 Board"
>
> @@ -77,7 +74,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
> source "board/d-link/dns325/Kconfig"
> source "board/iomega/iconnect/Kconfig"
> source "board/keymile/Kconfig"
> -source "board/LaCie/netspace_v2/Kconfig"
> source "board/raidsonic/ib62x0/Kconfig"
> source "board/Seagate/dockstar/Kconfig"
> source "board/Seagate/goflexhome/Kconfig"
> diff --git a/board/LaCie/netspace_v2/Kconfig b/board/LaCie/netspace_v2/Kconfig
> deleted file mode 100644
> index 930b822dfb..0000000000
> --- a/board/LaCie/netspace_v2/Kconfig
> +++ /dev/null
> @@ -1,12 +0,0 @@
> -if TARGET_NETSPACE_V2
> -
> -config SYS_BOARD
> - default "netspace_v2"
> -
> -config SYS_VENDOR
> - default "LaCie"
> -
> -config SYS_CONFIG_NAME
> - default "lacie_kw"
> -
> -endif
> diff --git a/board/LaCie/netspace_v2/MAINTAINERS b/board/LaCie/netspace_v2/MAINTAINERS
> deleted file mode 100644
> index 55fd50d4eb..0000000000
> --- a/board/LaCie/netspace_v2/MAINTAINERS
> +++ /dev/null
> @@ -1,14 +0,0 @@
> -NETSPACE_V2 BOARD
> -M: Simon Guinot <simon.guinot@sequanux.org>
> -S: Maintained
> -F: board/LaCie/netspace_v2/
> -F: include/configs/lacie_kw.h
> -F: configs/inetspace_v2_defconfig
> -F: configs/netspace_max_v2_defconfig
> -F: configs/netspace_v2_defconfig
> -
> -NETSPACE_LITE_V2 BOARD
> -#M: -
> -S: Maintained
> -F: configs/netspace_lite_v2_defconfig
> -F: configs/netspace_mini_v2_defconfig
> diff --git a/board/LaCie/netspace_v2/Makefile b/board/LaCie/netspace_v2/Makefile
> deleted file mode 100644
> index a6270bdd4b..0000000000
> --- a/board/LaCie/netspace_v2/Makefile
> +++ /dev/null
> @@ -1,10 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -
> -obj-y := netspace_v2.o ../common/common.o
> diff --git a/board/LaCie/netspace_v2/kwbimage-is2.cfg b/board/LaCie/netspace_v2/kwbimage-is2.cfg
> deleted file mode 100644
> index 50f584ae70..0000000000
> --- a/board/LaCie/netspace_v2/kwbimage-is2.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM spi # Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000618 # DDR Configuration register
> -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
> -# bit 4: 0=addr/cmd in smame cycle
> -# bit 5: 0=clk is driven during self refresh, we don't care for APX
> -# bit 6: 0=use recommended falling edge of clk for addr/cmd
> -# bit14: 0=input buffer always powered up
> -# bit18: 1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31: 0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
> -# bit7-4: TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20: TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
> -# bit6-0: TRFC
> -# bit8-7: TR2R
> -# bit10-9: TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x00000008 # DDR Address Control
> -# bit1-0: 00, Cs0width=x8
> -# bit3-2: 10, Cs0size=512Mb
> -# bit5-4: 00, Cs2width=nonexistent
> -# bit7-6: 00, Cs1size =nonexistent
> -# bit9-8: 00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16: 0, Cs0AddrSel
> -# bit17: 0, Cs1AddrSel
> -# bit18: 0, Cs2AddrSel
> -# bit19: 0, Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> -# bit0: 0, OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000 # DDR Operation
> -# bit3-0: 0x0, DDR cmd
> -# bit31-4: 0 required
> -
> -DATA 0xFFD0141C 0x00000632 # DDR Mode
> -# bit2-0: 2, BurstLen=2 required
> -# bit3: 0, BurstType=0 required
> -# bit6-4: 4, CL=5
> -# bit7: 0, TestMode=0 normal
> -# bit8: 0, DLL reset=0 normal
> -# bit11-9: 6, auto-precharge write recovery ????????????
> -# bit12: 0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000004 # DDR Extended Mode
> -# bit0: 0, DDR DLL enabled
> -# bit1: 1, DDR drive strenght reduced
> -# bit2: 1, DDR ODT control lsd enabled
> -# bit5-3: 000, required
> -# bit6: 1, DDR ODT control msb, enabled
> -# bit9-7: 000, required
> -# bit10: 0, differential DQS enabled
> -# bit11: 0, required
> -# bit12: 0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
> -# bit2-0: 111, required
> -# bit3 : 1 , MBUS Burst Chop disabled
> -# bit6-4: 111, required
> -# bit7 : 1 , D2P Latency enabled
> -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9 : 0 , no half clock cycle addition to dataout
> -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0 required
> -
> -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
> -# bit0: 1, Window enabled
> -# bit1: 0, Write Protect disabled
> -# bit3-2: 00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
> -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2: 01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
> -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
> deleted file mode 100644
> index 092353a06d..0000000000
> --- a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM spi # Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000618 # DDR Configuration register
> -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x34143000 # DDR Controller Control Low
> -# bit 4: 0=addr/cmd in smame cycle
> -# bit 5: 0=clk is driven during self refresh, we don't care for APX
> -# bit 6: 0=use recommended falling edge of clk for addr/cmd
> -# bit14: 0=input buffer always powered up
> -# bit18: 1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31: 0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
> -# bit7-4: TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20: TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
> -# bit6-0: TRFC
> -# bit8-7: TR2R
> -# bit10-9: TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x0000DDDD # DDR Address Control
> -# bit1-0: 00, Cs0width=x8
> -# bit3-2: 10, Cs0size=512Mb
> -# bit5-4: 00, Cs2width=nonexistent
> -# bit7-6: 00, Cs1size =nonexistent
> -# bit9-8: 00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16: 0, Cs0AddrSel
> -# bit17: 0, Cs1AddrSel
> -# bit18: 0, Cs2AddrSel
> -# bit19: 0, Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> -# bit0: 0, OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000 # DDR Operation
> -# bit3-0: 0x0, DDR cmd
> -# bit31-4: 0 required
> -
> -DATA 0xFFD0141C 0x00000632 # DDR Mode
> -# bit2-0: 2, BurstLen=2 required
> -# bit3: 0, BurstType=0 required
> -# bit6-4: 4, CL=5
> -# bit7: 0, TestMode=0 normal
> -# bit8: 0, DLL reset=0 normal
> -# bit11-9: 6, auto-precharge write recovery ????????????
> -# bit12: 0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000004 # DDR Extended Mode
> -# bit0: 0, DDR DLL enabled
> -# bit1: 1, DDR drive strenght reduced
> -# bit2: 1, DDR ODT control lsd enabled
> -# bit5-3: 000, required
> -# bit6: 1, DDR ODT control msb, enabled
> -# bit9-7: 000, required
> -# bit10: 0, differential DQS enabled
> -# bit11: 0, required
> -# bit12: 0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
> -# bit2-0: 111, required
> -# bit3 : 1 , MBUS Burst Chop disabled
> -# bit6-4: 111, required
> -# bit7 : 1 , D2P Latency enabled
> -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9 : 0 , no half clock cycle addition to dataout
> -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0 required
> -
> -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
> -# bit0: 1, Window enabled
> -# bit1: 0, Write Protect disabled
> -# bit3-2: 00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
> -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2: 01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
> -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/netspace_v2/kwbimage.cfg b/board/LaCie/netspace_v2/kwbimage.cfg
> deleted file mode 100644
> index 1ed03fa9a9..0000000000
> --- a/board/LaCie/netspace_v2/kwbimage.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM spi # Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000618 # DDR Configuration register
> -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
> -# bit 4: 0=addr/cmd in smame cycle
> -# bit 5: 0=clk is driven during self refresh, we don't care for APX
> -# bit 6: 0=use recommended falling edge of clk for addr/cmd
> -# bit14: 0=input buffer always powered up
> -# bit18: 1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31: 0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
> -# bit7-4: TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20: TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
> -# bit6-0: TRFC
> -# bit8-7: TR2R
> -# bit10-9: TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x0000000C # DDR Address Control
> -# bit1-0: 00, Cs0width=x8
> -# bit3-2: 11, Cs0size=1Gb
> -# bit5-4: 00, Cs2width=nonexistent
> -# bit7-6: 00, Cs1size =nonexistent
> -# bit9-8: 00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16: 0, Cs0AddrSel
> -# bit17: 0, Cs1AddrSel
> -# bit18: 0, Cs2AddrSel
> -# bit19: 0, Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> -# bit0: 0, OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000 # DDR Operation
> -# bit3-0: 0x0, DDR cmd
> -# bit31-4: 0 required
> -
> -DATA 0xFFD0141C 0x00000632 # DDR Mode
> -# bit2-0: 2, BurstLen=2 required
> -# bit3: 0, BurstType=0 required
> -# bit6-4: 4, CL=5
> -# bit7: 0, TestMode=0 normal
> -# bit8: 0, DLL reset=0 normal
> -# bit11-9: 6, auto-precharge write recovery ????????????
> -# bit12: 0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000004 # DDR Extended Mode
> -# bit0: 0, DDR DLL enabled
> -# bit1: 1, DDR drive strenght reduced
> -# bit2: 1, DDR ODT control lsd enabled
> -# bit5-3: 000, required
> -# bit6: 1, DDR ODT control msb, enabled
> -# bit9-7: 000, required
> -# bit10: 0, differential DQS enabled
> -# bit11: 0, required
> -# bit12: 0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
> -# bit2-0: 111, required
> -# bit3 : 1 , MBUS Burst Chop disabled
> -# bit6-4: 111, required
> -# bit7 : 1 , D2P Latency enabled
> -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9 : 0 , no half clock cycle addition to dataout
> -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0 required
> -
> -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
> -# bit0: 1, Window enabled
> -# bit1: 0, Write Protect disabled
> -# bit3-2: 00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
> -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2: 01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
> -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c
> deleted file mode 100644
> index 011cc563d1..0000000000
> --- a/board/LaCie/netspace_v2/netspace_v2.c
> +++ /dev/null
> @@ -1,120 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> - */
> -
> -#include <common.h>
> -#include <command.h>
> -#include <env.h>
> -#include <init.h>
> -#include <net.h>
> -#include <asm/mach-types.h>
> -#include <asm/arch/cpu.h>
> -#include <asm/arch/soc.h>
> -#include <asm/arch/mpp.h>
> -#include <asm/arch/gpio.h>
> -
> -#include "netspace_v2.h"
> -#include "../common/common.h"
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -int board_early_init_f(void)
> -{
> - /* Gpio configuration */
> - mvebu_config_gpio(NETSPACE_V2_OE_VAL_LOW, NETSPACE_V2_OE_VAL_HIGH,
> - NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
> -
> - /* Multi-Purpose Pins Functionality configuration */
> - static const u32 kwmpp_config[] = {
> - MPP0_SPI_SCn,
> - MPP1_SPI_MOSI,
> - MPP2_SPI_SCK,
> - MPP3_SPI_MISO,
> - MPP4_NF_IO6,
> - MPP5_NF_IO7,
> - MPP6_SYSRST_OUTn,
> - MPP7_GPO, /* Fan speed (bit 1) */
> - MPP8_TW_SDA,
> - MPP9_TW_SCK,
> - MPP10_UART0_TXD,
> - MPP11_UART0_RXD,
> - MPP12_GPO, /* Red led */
> - MPP14_GPIO, /* USB fuse */
> - MPP16_GPIO, /* SATA 0 power */
> - MPP17_GPIO, /* SATA 1 power */
> - MPP18_NF_IO0,
> - MPP19_NF_IO1,
> - MPP20_SATA1_ACTn,
> - MPP21_SATA0_ACTn,
> - MPP22_GPIO, /* Fan speed (bit 0) */
> - MPP23_GPIO, /* Fan power */
> - MPP24_GPIO, /* USB mode select */
> - MPP25_GPIO, /* Fan rotation fail */
> - MPP26_GPIO, /* USB vbus-in detection */
> - MPP28_GPIO, /* USB enable vbus-out */
> - MPP29_GPIO, /* Blue led (slow register) */
> - MPP30_GPIO, /* Blue led (command register) */
> - MPP31_GPIO, /* Board power off */
> - MPP32_GPIO, /* Button (0 = Released, 1 = Pushed) */
> - MPP33_GPIO, /* Fan speed (bit 2) */
> - 0
> - };
> - kirkwood_mpp_conf(kwmpp_config, NULL);
> -
> - return 0;
> -}
> -
> -int board_init(void)
> -{
> - /* Machine number */
> - gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
> -
> - /* Boot parameters address */
> - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> -
> - return 0;
> -}
> -
> -#if defined(CONFIG_MISC_INIT_R)
> -int misc_init_r(void)
> -{
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
> - if (!env_get("ethaddr")) {
> - uchar mac[6];
> - if (lacie_read_mac_address(mac) == 0)
> - eth_env_set_enetaddr("ethaddr", mac);
> - }
> -#endif
> - return 0;
> -}
> -#endif
> -
> -#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
> -/* Configure and initialize PHY */
> -void reset_phy(void)
> -{
> -#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> - mv_phy_88e1318_init("egiga0", 0);
> -#else
> - mv_phy_88e1116_init("egiga0", 8);
> -#endif
> -}
> -#endif
> -
> -#if defined(CONFIG_KIRKWOOD_GPIO)
> -/* Return GPIO button status */
> -static int
> -do_read_button(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
> -{
> - return kw_gpio_get_value(NETSPACE_V2_GPIO_BUTTON);
> -}
> -
> -U_BOOT_CMD(button, 1, 1, do_read_button,
> - "Return GPIO button status 0=off 1=on", "");
> -#endif
> diff --git a/board/LaCie/netspace_v2/netspace_v2.h b/board/LaCie/netspace_v2/netspace_v2.h
> deleted file mode 100644
> index 2c930171ea..0000000000
> --- a/board/LaCie/netspace_v2/netspace_v2.h
> +++ /dev/null
> @@ -1,22 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> - */
> -
> -#ifndef NETSPACE_V2_H
> -#define NETSPACE_V2_H
> -
> -/* GPIO configuration */
> -#define NETSPACE_V2_OE_LOW 0x06004000
> -#define NETSPACE_V2_OE_HIGH 0x00000031
> -#define NETSPACE_V2_OE_VAL_LOW 0x10030000
> -#define NETSPACE_V2_OE_VAL_HIGH 0x00000000
> -
> -#define NETSPACE_V2_GPIO_BUTTON 32
> -
> -#endif /* NETSPACE_V2_H */
> diff --git a/configs/inetspace_v2_defconfig b/configs/inetspace_v2_defconfig
> deleted file mode 100644
> index 6144eb5fad..0000000000
> --- a/configs/inetspace_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NETSPACE_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" IS v2"
> -CONFIG_SYS_EXTRA_OPTIONS="INETSPACE_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="ns2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-is2"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/netspace_lite_v2_defconfig b/configs/netspace_lite_v2_defconfig
> deleted file mode 100644
> index c744d2c58e..0000000000
> --- a/configs/netspace_lite_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NETSPACE_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" NS v2 Lite"
> -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_LITE_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="ns2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2lite"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/netspace_max_v2_defconfig b/configs/netspace_max_v2_defconfig
> deleted file mode 100644
> index 8602729fcb..0000000000
> --- a/configs/netspace_max_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NETSPACE_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" NS Max v2"
> -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MAX_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="ns2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2max"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/netspace_mini_v2_defconfig b/configs/netspace_mini_v2_defconfig
> deleted file mode 100644
> index ba9301de4d..0000000000
> --- a/configs/netspace_mini_v2_defconfig
> +++ /dev/null
> @@ -1,48 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NETSPACE_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" NS v2 Mini"
> -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MINI_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="ns2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2mini"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> diff --git a/configs/netspace_v2_defconfig b/configs/netspace_v2_defconfig
> deleted file mode 100644
> index 6ba1ef423e..0000000000
> --- a/configs/netspace_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NETSPACE_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" NS v2"
> -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="ns2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> --
> 2.25.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200620/ac21b00e/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 2/4] arm: Remove d2net_v2 board
2020-06-20 0:25 ` Tom Rini
@ 2020-06-24 22:42 ` Simon Guinot
0 siblings, 0 replies; 14+ messages in thread
From: Simon Guinot @ 2020-06-24 22:42 UTC (permalink / raw)
To: u-boot
On Fri, Jun 19, 2020 at 08:25:59PM -0400, Tom Rini wrote:
> On Sat, Jun 20, 2020 at 02:24:47AM +0200, Simon Guinot wrote:
> > On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> > > On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > > > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > > > Hi Jagan,
> > > >
> > > > > This board has not been converted to CONFIG_DM by the deadline.
> > > >
> > > > Is that possible to negociate a new deadline ?
> > >
> > > Well, when will you be able to spend some time bringing the platform up
> > > to current standards? Doing a quick build for net2big_v2 I see:
> > > +(net2big_v2) ===================== WARNING ======================
> > > +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> > > +(net2big_v2) compulsory starting with the v2020.01 release.
> > > +(net2big_v2) Failure to update may result in board removal.
> > > +(net2big_v2) See doc/driver-model/migration.rst for more info.
> > > +(net2big_v2) ====================================================
> > > +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> > > +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> > > +(net2big_v2) Failure to update by the deadline may result in board removal.
> > > +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> > > +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> > > +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> > > +(net2big_v2) release.
> > > +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> > > +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> > > +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> > > +(net2big_v2) for Ethernet drivers). Please update the board to use
> > > +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> > > +(net2big_v2) update by the deadline may result in board removal.
> > >
> > > So there's a lot of stuff that needs updating. Conversion to CONFIG_DM
> > > is what you'll need to then convert SPI, ETH and USB to use DM and the
> > > IDE driver also needs attention and conversion. Thanks!
> >
> > Hi Tom,
> >
> > I am working on it. But so far it is not going very well and the whole
> > thing is turning into a debug session.
> >
> > But I'll do my best and whatever the result will be, I'll send you an
> > update by the end of the next week.
> >
> > Is this acceptable to you ?
Hi Tom,
I just sent a patch series converting the LaCie boards to use DM
drivers.
I apologize for missing all this DM deadlines.
Simon
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200625/04c34ae9/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4)
2020-06-19 8:31 ` [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Chris Packham
@ 2020-06-25 1:05 ` Chris Packham
0 siblings, 0 replies; 14+ messages in thread
From: Chris Packham @ 2020-06-25 1:05 UTC (permalink / raw)
To: u-boot
On Fri, Jun 19, 2020 at 8:31 PM Chris Packham <judge.packham@gmail.com> wrote:
>
> Hi Jagan,
>
> On Fri, 19 Jun 2020, 5:45 AM Jagan Teki, <jagan@amarulasolutions.com> wrote:
>>
>> Series of kirkwood boards to switch DM_SPI and drop
>> which are not DM enabled still.
>>
>> Any inputs?
>> Jagan.
>
>
> I had a quick glance over the series and it looks good to me.
>
> I'm fortunate enough to be able to get into the office so I'll try and give this a spin on the kirkwood board I have on Monday.
>
Tooks a bit longer to dust off the kirkwood board than I expected. For
this series
Tested-by: Chris Packham <judge.packham@gmail.com>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH
2020-06-18 17:45 ` [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH Jagan Teki
@ 2020-07-08 6:50 ` Jagan Teki
0 siblings, 0 replies; 14+ messages in thread
From: Jagan Teki @ 2020-07-08 6:50 UTC (permalink / raw)
To: u-boot
On Thu, Jun 18, 2020 at 11:15 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> Enable DM_SPI, DM_SPI_FLASH for db-88f6281-bp-nand board.
>
> Cc: Chris Packham <judge.packham@gmail.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
Applied to u-boot-spi/master
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2020-07-08 6:50 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-18 17:45 [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Jagan Teki
2020-06-18 17:45 ` [PATCH v3 1/4] spi: kirkwood: Drop nondm code Jagan Teki
2020-06-18 17:45 ` [PATCH v3 2/4] arm: Remove d2net_v2 board Jagan Teki
2020-06-18 22:02 ` Simon Guinot
2020-06-18 22:25 ` Tom Rini
2020-06-20 0:24 ` Simon Guinot
2020-06-20 0:25 ` Tom Rini
2020-06-24 22:42 ` Simon Guinot
2020-06-18 17:45 ` [PATCH v3 3/4] db-88f6281-bp-nand: Enable DM_SPI/SPI_FLASH Jagan Teki
2020-07-08 6:50 ` Jagan Teki
2020-06-18 17:45 ` [PATCH v3 4/4] arm: Remove netspace_v2 board Jagan Teki
2020-06-20 0:26 ` Simon Guinot
2020-06-19 8:31 ` [PATCH v3 0/4] spi: kirkwood: dm-conversion (part4) Chris Packham
2020-06-25 1:05 ` Chris Packham
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.