* [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs
@ 2020-06-22 22:27 Bjorn Andersson
2020-06-22 22:27 ` [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11 Bjorn Andersson
` (6 more replies)
0 siblings, 7 replies; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
With the driver code in place, add the necessary dts nodes to enable three of
the remoteprocs found on Qualcomm SM8250 and finally enable the missing
QCOM_IPCC driver in defconfig.
Bjorn Andersson (6):
arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11
arm64: dts: qcom: sm8250: Add IPCC
arm64: dts: qcom: sm8250: Add QMP AOSS node
arm64: dts: qcom: sm8250: Add SMP2P nodes
arm64: dts: qcom: sm8250: Add remoteprocs
arm64: defconfig: Enable Qualcomm IPCC driver
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 22 ++-
arch/arm64/boot/dts/qcom/sm8250.dtsi | 212 ++++++++++++++++++++++++
arch/arm64/configs/defconfig | 1 +
3 files changed, 228 insertions(+), 7 deletions(-)
--
2.26.2
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 11:34 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC Bjorn Andersson
` (5 subsequent siblings)
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
rather than as a regulator. As such it's available from the rpmhpd as
the SM8250_LCX power domain.
Fixes: ec13d5c23a33 ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 7 -------
1 file changed, 7 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 2fc9e7ff0060..63d259931c4d 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -140,13 +140,6 @@ vreg_l10a_1p8: ldo10 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
- vreg_l11a_0p75: ldo11 {
- regulator-name = "vreg_l11a_0p75";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
vreg_l12a_1p8: ldo12 {
regulator-name = "vreg_l12a_1p8";
regulator-min-microvolt = <1800000>;
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
2020-06-22 22:27 ` [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11 Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 2:43 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node Bjorn Andersson
` (4 subsequent siblings)
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
Add the IPCC node, used to send and receive IPC signals with
remoteprocs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index e583a01cbcf1..74a7ca96177e 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-sm8250.h>
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -329,6 +330,15 @@ gcc: clock-controller@100000 {
clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
};
+ ipcc: interrupt-controller@408000 {
+ compatible = "qcom,sm8250-ipcc", "qcom,ipcc";
+ reg = <0 0x00408000 0 0x1000>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #mbox-cells = <2>;
+ };
+
qupv3_id_2: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x008c0000 0x0 0x6000>;
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
2020-06-22 22:27 ` [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11 Bjorn Andersson
2020-06-22 22:27 ` [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 2:47 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes Bjorn Andersson
` (3 subsequent siblings)
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
Add a node for the QMP AOSS.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 74a7ca96177e..246e6f279aa8 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -7,6 +7,7 @@
#include <dt-bindings/clock/qcom,gcc-sm8250.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-aoss-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -989,6 +990,19 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
+ aoss_qmp: qmp@c300000 {
+ compatible = "qcom,sm8250-aoss-qmp";
+ reg = <0 0x0c300000 0 0x100000>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_AOP
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_AOP
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ #clock-cells = <0>;
+ #power-domain-cells = <1>;
+ };
+
spmi_bus: spmi@c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x0 0x0c440000 0x0 0x0001100>,
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
` (2 preceding siblings ...)
2020-06-22 22:27 ` [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 2:48 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs Bjorn Andersson
` (2 subsequent siblings)
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250.dtsi | 72 ++++++++++++++++++++++++++++
1 file changed, 72 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 246e6f279aa8..364d9a798673 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -314,6 +314,78 @@ smem: qcom,smem {
hwlocks = <&tcsr_mutex 3>;
};
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ smp2p_adsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_adsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-cdsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <94>, <432>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <5>;
+
+ smp2p_cdsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_cdsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-slpi {
+ compatible = "qcom,smp2p";
+ qcom,smem = <481>, <430>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_SMP2P
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_SMP2P>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <3>;
+
+ smp2p_slpi_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_slpi_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
` (3 preceding siblings ...)
2020-06-22 22:27 ` [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 2:54 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver Bjorn Andersson
2020-06-23 8:09 ` [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Vinod Koul
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 15 +++
arch/arm64/boot/dts/qcom/sm8250.dtsi | 116 ++++++++++++++++++++++++
2 files changed, 131 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 63d259931c4d..6894f8490dae 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -55,6 +55,11 @@ vreg_s6c_0p88: smpc6-regulator {
};
};
+&adsp {
+ status = "okay";
+ firmware-name = "qcom/sm8250/adsp.mbn";
+};
+
&apps_rsc {
pm8150-rpmh-regulators {
compatible = "qcom,pm8150-rpmh-regulators";
@@ -348,10 +353,20 @@ vreg_l7f_1p8: ldo7 {
};
};
+&cdsp {
+ status = "okay";
+ firmware-name = "qcom/sm8250/cdsp.mbn";
+};
+
&qupv3_id_1 {
status = "okay";
};
+&slpi {
+ status = "okay";
+ firmware-name = "qcom/sm8250/slpi.mbn";
+};
+
&tlmm {
gpio-reserved-ranges = <28 4>, <40 4>;
};
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 364d9a798673..a21299b9c62f 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -1052,6 +1052,83 @@ tcsr_mutex_regs: syscon@1f40000 {
reg = <0x0 0x01f40000 0x0 0x40000>;
};
+ slpi: remoteproc@5c00000 {
+ compatible = "qcom,sm8250-slpi-pas";
+ reg = <0 0x05c00000 0 0x4000>;
+
+ interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
+ <&rpmhpd SM8250_LCX>,
+ <&rpmhpd SM8250_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&slpi_mem>;
+
+ qcom,smem-states = <&smp2p_slpi_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <3>;
+ };
+ };
+
+ cdsp: remoteproc@8300000 {
+ compatible = "qcom,sm8250-cdsp-pas";
+ reg = <0 0x08300000 0 0x10000>;
+
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
+ <&rpmhpd SM8250_CX>;
+ power-domain-names = "load_state", "cx";
+
+ memory-region = <&cdsp_mem>;
+
+ qcom,smem-states = <&smp2p_cdsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <5>;
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8250-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
@@ -1668,6 +1745,45 @@ config {
};
};
+ adsp: remoteproc@17300000 {
+ compatible = "qcom,sm8250-adsp-pas";
+ reg = <0 0x17300000 0 0x100>;
+
+ interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
+ <&rpmhpd SM8250_LCX>,
+ <&rpmhpd SM8250_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&adsp_mem>;
+
+ qcom,smem-states = <&smp2p_adsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <2>;
+ };
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
` (4 preceding siblings ...)
2020-06-22 22:27 ` [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs Bjorn Andersson
@ 2020-06-22 22:27 ` Bjorn Andersson
2020-06-23 2:56 ` Manivannan Sadhasivam
2020-06-23 8:09 ` [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Vinod Koul
6 siblings, 1 reply; 14+ messages in thread
From: Bjorn Andersson @ 2020-06-22 22:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Manivannan Sadhasivam
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
The IPCC hardware block provides a mechanism for triggering interrupts
between co-processors in recent Qualcomm SoCs. This is used as basis for
most form of communication between co-processors, so enable this
support.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/configs/defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 5848799dcad0..b3d13e1a052a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -834,6 +834,7 @@ CONFIG_IMX_MBOX=y
CONFIG_PLATFORM_MHU=y
CONFIG_BCM2835_MBOX=y
CONFIG_QCOM_APCS_IPC=y
+CONFIG_QCOM_IPCC=y
CONFIG_ROCKCHIP_IOMMU=y
CONFIG_TEGRA_IOMMU_SMMU=y
CONFIG_ARM_SMMU=y
--
2.26.2
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC
2020-06-22 22:27 ` [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC Bjorn Andersson
@ 2020-06-23 2:43 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 2:43 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:43PM -0700, Bjorn Andersson wrote:
> Add the IPCC node, used to send and receive IPC signals with
> remoteprocs.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8250.dtsi | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index e583a01cbcf1..74a7ca96177e 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -6,6 +6,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-sm8250.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/mailbox/qcom-ipcc.h>
> #include <dt-bindings/power/qcom-rpmpd.h>
> #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>
> @@ -329,6 +330,15 @@ gcc: clock-controller@100000 {
> clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
> };
>
> + ipcc: interrupt-controller@408000 {
ipcc: mailbox@408000
Other than this,
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> + compatible = "qcom,sm8250-ipcc", "qcom,ipcc";
> + reg = <0 0x00408000 0 0x1000>;
> + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + #mbox-cells = <2>;
> + };
> +
> qupv3_id_2: geniqup@8c0000 {
> compatible = "qcom,geni-se-qup";
> reg = <0x0 0x008c0000 0x0 0x6000>;
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node
2020-06-22 22:27 ` [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node Bjorn Andersson
@ 2020-06-23 2:47 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 2:47 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:44PM -0700, Bjorn Andersson wrote:
> Add a node for the QMP AOSS.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm64/boot/dts/qcom/sm8250.dtsi | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 74a7ca96177e..246e6f279aa8 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -7,6 +7,7 @@
> #include <dt-bindings/clock/qcom,gcc-sm8250.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> #include <dt-bindings/mailbox/qcom-ipcc.h>
> +#include <dt-bindings/power/qcom-aoss-qmp.h>
> #include <dt-bindings/power/qcom-rpmpd.h>
> #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>
> @@ -989,6 +990,19 @@ pdc: interrupt-controller@b220000 {
> interrupt-controller;
> };
>
> + aoss_qmp: qmp@c300000 {
> + compatible = "qcom,sm8250-aoss-qmp";
> + reg = <0 0x0c300000 0 0x100000>;
> + interrupts-extended = <&ipcc IPCC_CLIENT_AOP
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_AOP
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + #clock-cells = <0>;
> + #power-domain-cells = <1>;
> + };
> +
> spmi_bus: spmi@c440000 {
> compatible = "qcom,spmi-pmic-arb";
> reg = <0x0 0x0c440000 0x0 0x0001100>,
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes
2020-06-22 22:27 ` [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes Bjorn Andersson
@ 2020-06-23 2:48 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 2:48 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:45PM -0700, Bjorn Andersson wrote:
> SMP2P is used for interrupting and being interrupted about remoteproc
> state changes related to the audio, compute and sensor subsystems.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm64/boot/dts/qcom/sm8250.dtsi | 72 ++++++++++++++++++++++++++++
> 1 file changed, 72 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 246e6f279aa8..364d9a798673 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -314,6 +314,78 @@ smem: qcom,smem {
> hwlocks = <&tcsr_mutex 3>;
> };
>
> + smp2p-adsp {
> + compatible = "qcom,smp2p";
> + qcom,smem = <443>, <429>;
> + interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
> + IPCC_MPROC_SIGNAL_SMP2P
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_LPASS
> + IPCC_MPROC_SIGNAL_SMP2P>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <2>;
> +
> + smp2p_adsp_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + smp2p_adsp_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smp2p-cdsp {
> + compatible = "qcom,smp2p";
> + qcom,smem = <94>, <432>;
> + interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
> + IPCC_MPROC_SIGNAL_SMP2P
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_CDSP
> + IPCC_MPROC_SIGNAL_SMP2P>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <5>;
> +
> + smp2p_cdsp_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + smp2p_cdsp_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + smp2p-slpi {
> + compatible = "qcom,smp2p";
> + qcom,smem = <481>, <430>;
> + interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
> + IPCC_MPROC_SIGNAL_SMP2P
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_SLPI
> + IPCC_MPROC_SIGNAL_SMP2P>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <3>;
> +
> + smp2p_slpi_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + smp2p_slpi_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> soc: soc@0 {
> #address-cells = <2>;
> #size-cells = <2>;
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs
2020-06-22 22:27 ` [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs Bjorn Andersson
@ 2020-06-23 2:54 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 2:54 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:46PM -0700, Bjorn Andersson wrote:
> Add remoteproc nodes for the audio, compute and sensor cores, define
> glink for each one and enable them on the MTP with appropriate firmware
> defined.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 15 +++
> arch/arm64/boot/dts/qcom/sm8250.dtsi | 116 ++++++++++++++++++++++++
> 2 files changed, 131 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> index 63d259931c4d..6894f8490dae 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> @@ -55,6 +55,11 @@ vreg_s6c_0p88: smpc6-regulator {
> };
> };
>
> +&adsp {
> + status = "okay";
> + firmware-name = "qcom/sm8250/adsp.mbn";
> +};
> +
> &apps_rsc {
> pm8150-rpmh-regulators {
> compatible = "qcom,pm8150-rpmh-regulators";
> @@ -348,10 +353,20 @@ vreg_l7f_1p8: ldo7 {
> };
> };
>
> +&cdsp {
> + status = "okay";
> + firmware-name = "qcom/sm8250/cdsp.mbn";
> +};
> +
> &qupv3_id_1 {
> status = "okay";
> };
>
> +&slpi {
> + status = "okay";
> + firmware-name = "qcom/sm8250/slpi.mbn";
> +};
> +
> &tlmm {
> gpio-reserved-ranges = <28 4>, <40 4>;
> };
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 364d9a798673..a21299b9c62f 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -1052,6 +1052,83 @@ tcsr_mutex_regs: syscon@1f40000 {
> reg = <0x0 0x01f40000 0x0 0x40000>;
> };
>
> + slpi: remoteproc@5c00000 {
> + compatible = "qcom,sm8250-slpi-pas";
> + reg = <0 0x05c00000 0 0x4000>;
> +
> + interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
> + <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready",
> + "handover", "stop-ack";
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "xo";
> +
> + power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
> + <&rpmhpd SM8250_LCX>,
> + <&rpmhpd SM8250_LMX>;
> + power-domain-names = "load_state", "lcx", "lmx";
> +
> + memory-region = <&slpi_mem>;
> +
> + qcom,smem-states = <&smp2p_slpi_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_SLPI
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + label = "lpass";
> + qcom,remote-pid = <3>;
> + };
> + };
> +
> + cdsp: remoteproc@8300000 {
> + compatible = "qcom,sm8250-cdsp-pas";
> + reg = <0 0x08300000 0 0x10000>;
> +
> + interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
> + <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready",
> + "handover", "stop-ack";
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "xo";
> +
> + power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
> + <&rpmhpd SM8250_CX>;
> + power-domain-names = "load_state", "cx";
> +
> + memory-region = <&cdsp_mem>;
> +
> + qcom,smem-states = <&smp2p_cdsp_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_CDSP
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + label = "lpass";
> + qcom,remote-pid = <5>;
> + };
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,sm8250-pdc", "qcom,pdc";
> reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> @@ -1668,6 +1745,45 @@ config {
> };
> };
>
> + adsp: remoteproc@17300000 {
> + compatible = "qcom,sm8250-adsp-pas";
> + reg = <0 0x17300000 0 0x100>;
> +
> + interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
> + <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready",
> + "handover", "stop-ack";
> +
> + clocks = <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "xo";
> +
> + power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
> + <&rpmhpd SM8250_LCX>,
> + <&rpmhpd SM8250_LMX>;
> + power-domain-names = "load_state", "lcx", "lmx";
> +
> + memory-region = <&adsp_mem>;
> +
> + qcom,smem-states = <&smp2p_adsp_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_LPASS
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + label = "lpass";
> + qcom,remote-pid = <2>;
> + };
> + };
> +
> intc: interrupt-controller@17a00000 {
> compatible = "arm,gic-v3";
> #interrupt-cells = <3>;
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver
2020-06-22 22:27 ` [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver Bjorn Andersson
@ 2020-06-23 2:56 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 2:56 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:47PM -0700, Bjorn Andersson wrote:
> The IPCC hardware block provides a mechanism for triggering interrupts
> between co-processors in recent Qualcomm SoCs. This is used as basis for
> most form of communication between co-processors, so enable this
> support.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm64/configs/defconfig | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index 5848799dcad0..b3d13e1a052a 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -834,6 +834,7 @@ CONFIG_IMX_MBOX=y
> CONFIG_PLATFORM_MHU=y
> CONFIG_BCM2835_MBOX=y
> CONFIG_QCOM_APCS_IPC=y
> +CONFIG_QCOM_IPCC=y
> CONFIG_ROCKCHIP_IOMMU=y
> CONFIG_TEGRA_IOMMU_SMMU=y
> CONFIG_ARM_SMMU=y
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
` (5 preceding siblings ...)
2020-06-22 22:27 ` [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver Bjorn Andersson
@ 2020-06-23 8:09 ` Vinod Koul
6 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2020-06-23 8:09 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, Manivannan Sadhasivam,
linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel
On 22-06-20, 15:27, Bjorn Andersson wrote:
> With the driver code in place, add the necessary dts nodes to enable three of
> the remoteprocs found on Qualcomm SM8250 and finally enable the missing
> QCOM_IPCC driver in defconfig.
All look great to me:
Reviewed-by: Vinod Koul <vkoul@kernel.org>
--
~Vinod
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11
2020-06-22 22:27 ` [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11 Bjorn Andersson
@ 2020-06-23 11:34 ` Manivannan Sadhasivam
0 siblings, 0 replies; 14+ messages in thread
From: Manivannan Sadhasivam @ 2020-06-23 11:34 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, Dmitry Baryshkov, linux-arm-msm, devicetree,
linux-kernel, linux-arm-kernel
On Mon, Jun 22, 2020 at 03:27:42PM -0700, Bjorn Andersson wrote:
> PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
> rather than as a regulator. As such it's available from the rpmhpd as
> the SM8250_LCX power domain.
>
> Fixes: ec13d5c23a33 ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 7 -------
> 1 file changed, 7 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> index 2fc9e7ff0060..63d259931c4d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> @@ -140,13 +140,6 @@ vreg_l10a_1p8: ldo10 {
> regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> - vreg_l11a_0p75: ldo11 {
> - regulator-name = "vreg_l11a_0p75";
> - regulator-min-microvolt = <800000>;
> - regulator-max-microvolt = <800000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> - };
> -
> vreg_l12a_1p8: ldo12 {
> regulator-name = "vreg_l12a_1p8";
> regulator-min-microvolt = <1800000>;
> --
> 2.26.2
>
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2020-06-23 11:37 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-22 22:27 [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Bjorn Andersson
2020-06-22 22:27 ` [PATCH 1/6] arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11 Bjorn Andersson
2020-06-23 11:34 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 2/6] arm64: dts: qcom: sm8250: Add IPCC Bjorn Andersson
2020-06-23 2:43 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 3/6] arm64: dts: qcom: sm8250: Add QMP AOSS node Bjorn Andersson
2020-06-23 2:47 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 4/6] arm64: dts: qcom: sm8250: Add SMP2P nodes Bjorn Andersson
2020-06-23 2:48 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs Bjorn Andersson
2020-06-23 2:54 ` Manivannan Sadhasivam
2020-06-22 22:27 ` [PATCH 6/6] arm64: defconfig: Enable Qualcomm IPCC driver Bjorn Andersson
2020-06-23 2:56 ` Manivannan Sadhasivam
2020-06-23 8:09 ` [PATCH 0/6] arm64: dts: qcom: Enable SM8250 remoteprocs Vinod Koul
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.