* [PATCH 1/4] am335x: Update list of defconfigs
@ 2020-06-30 16:56 Tom Rini
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
` (3 more replies)
0 siblings, 4 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 16:56 UTC (permalink / raw)
To: u-boot
Both the am335x_boneblack and am335x_evm_usbspl configs have been gone
for a while, remove their entries from MAINTAINERS.
Signed-off-by: Tom Rini <trini@konsulko.com>
---
board/ti/am335x/MAINTAINERS | 2 --
1 file changed, 2 deletions(-)
diff --git a/board/ti/am335x/MAINTAINERS b/board/ti/am335x/MAINTAINERS
index 565f7055cdd3..e100adfd68ec 100644
--- a/board/ti/am335x/MAINTAINERS
+++ b/board/ti/am335x/MAINTAINERS
@@ -3,7 +3,5 @@ M: Tom Rini <trini@konsulko.com>
S: Maintained
F: board/ti/am335x/
F: include/configs/am335x_evm.h
-F: configs/am335x_boneblack_defconfig
F: configs/am335x_boneblack_vboot_defconfig
F: configs/am335x_evm_defconfig
-F: configs/am335x_evm_usbspl_defconfig
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 16:56 [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
@ 2020-06-30 16:56 ` Tom Rini
2020-06-30 17:07 ` Adam Ford
2020-06-30 18:49 ` Tom Rini
2020-06-30 16:56 ` [PATCH 3/4] ti816x_evm: Enable DM_MMC Tom Rini
` (2 subsequent siblings)
3 siblings, 2 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 16:56 UTC (permalink / raw)
To: u-boot
Disable USB support for now. There is non-trivial work required to
fully move the OMAP3 platforms to DM. While this work is in-progress,
disable USB support for now as we've gone well past the migration
deadline.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
configs/omap3_beagle_defconfig | 20 ++------------------
1 file changed, 2 insertions(+), 18 deletions(-)
diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig
index ed7cb8f2ff63..236a4f4f5f5a 100644
--- a/configs/omap3_beagle_defconfig
+++ b/configs/omap3_beagle_defconfig
@@ -9,6 +9,7 @@ CONFIG_NR_DRAM_BANKS=2
CONFIG_SPL=y
CONFIG_SPL_TEXT_BASE=0x40200000
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_ANDROID_BOOT_IMAGE=y
CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="usb start"
@@ -31,7 +32,6 @@ CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
CONFIG_CMD_SPI=y
-CONFIG_CMD_USB=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FS_UUID=y
@@ -50,8 +50,6 @@ CONFIG_ENV_IS_IN_NAND=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_USB_FUNCTION_FASTBOOT=y
-CONFIG_FASTBOOT_BUF_ADDR=0x82000000
CONFIG_LED_STATUS=y
CONFIG_LED_STATUS0=y
CONFIG_LED_STATUS_BIT=1
@@ -73,24 +71,10 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_OMAP3_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_OMAP3=y
-CONFIG_USB_MUSB_GADGET=y
-CONFIG_USB_MUSB_OMAP2PLUS=y
-CONFIG_TWL4030_USB=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="TI"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0xd022
-CONFIG_USB_ETHER=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_MCS7830=y
-CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_VIDEO_OMAP3=y
CONFIG_FAT_WRITE=y
CONFIG_BCH=y
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 3/4] ti816x_evm: Enable DM_MMC
2020-06-30 16:56 [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
@ 2020-06-30 16:56 ` Tom Rini
2020-06-30 21:15 ` Tom Rini
2020-06-30 16:56 ` [PATCH 4/4] ti814x: Remove platform Tom Rini
2020-06-30 21:15 ` [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
3 siblings, 1 reply; 12+ messages in thread
From: Tom Rini @ 2020-06-30 16:56 UTC (permalink / raw)
To: u-boot
This platform is already using DM in general and the MMC controller is
the early generation of what is compatible with "ti,omap4-hsmmc" so
enable DM_MMC (which in turn gets BLK enabled).
Signed-off-by: Tom Rini <trini@konsulko.com>
---
configs/ti816x_evm_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/configs/ti816x_evm_defconfig b/configs/ti816x_evm_defconfig
index 17aa6a02067c..033d35df4d02 100644
--- a/configs/ti816x_evm_defconfig
+++ b/configs/ti816x_evm_defconfig
@@ -47,6 +47,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_OMAP24XX=y
+CONFIG_DM_MMC=y
CONFIG_MMC_OMAP_HS=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 4/4] ti814x: Remove platform
2020-06-30 16:56 [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
2020-06-30 16:56 ` [PATCH 3/4] ti816x_evm: Enable DM_MMC Tom Rini
@ 2020-06-30 16:56 ` Tom Rini
2020-06-30 21:15 ` Tom Rini
2020-06-30 21:15 ` [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
3 siblings, 1 reply; 12+ messages in thread
From: Tom Rini @ 2020-06-30 16:56 UTC (permalink / raw)
To: u-boot
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work. As much of that work is well past the deadline, remove
this platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
---
arch/arm/mach-omap2/Kconfig | 1 -
board/ti/ti814x/Kconfig | 15 ---
board/ti/ti814x/MAINTAINERS | 6 --
board/ti/ti814x/Makefile | 11 --
board/ti/ti814x/evm.c | 190 -----------------------------------
board/ti/ti814x/evm.h | 8 --
board/ti/ti814x/mux.c | 86 ----------------
configs/ti814x_evm_defconfig | 45 ---------
8 files changed, 362 deletions(-)
delete mode 100644 board/ti/ti814x/Kconfig
delete mode 100644 board/ti/ti814x/MAINTAINERS
delete mode 100644 board/ti/ti814x/Makefile
delete mode 100644 board/ti/ti814x/evm.c
delete mode 100644 board/ti/ti814x/evm.h
delete mode 100644 board/ti/ti814x/mux.c
delete mode 100644 configs/ti814x_evm_defconfig
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 4c87cbc00f74..48bc80a6390a 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -181,7 +181,6 @@ source "board/BuR/brppt1/Kconfig"
source "board/siemens/draco/Kconfig"
source "board/siemens/pxm2/Kconfig"
source "board/siemens/rut/Kconfig"
-source "board/ti/ti814x/Kconfig"
source "board/ti/ti816x/Kconfig"
source "board/ti/am43xx/Kconfig"
source "board/ti/am335x/Kconfig"
diff --git a/board/ti/ti814x/Kconfig b/board/ti/ti814x/Kconfig
deleted file mode 100644
index 2960099a8e5b..000000000000
--- a/board/ti/ti814x/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_TI814X_EVM
-
-config SYS_BOARD
- default "ti814x"
-
-config SYS_VENDOR
- default "ti"
-
-config SYS_SOC
- default "am33xx"
-
-config SYS_CONFIG_NAME
- default "ti814x_evm"
-
-endif
diff --git a/board/ti/ti814x/MAINTAINERS b/board/ti/ti814x/MAINTAINERS
deleted file mode 100644
index b2ee39e8a339..000000000000
--- a/board/ti/ti814x/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-TI814X BOARD
-M: Tom Rini <trini@konsulko.com>
-S: Maintained
-F: board/ti/ti814x/
-F: include/configs/ti814x_evm.h
-F: configs/ti814x_evm_defconfig
diff --git a/board/ti/ti814x/Makefile b/board/ti/ti814x/Makefile
deleted file mode 100644
index c5ff8d072851..000000000000
--- a/board/ti/ti814x/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Makefile
-#
-# Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
-
-ifdef CONFIG_SPL_BUILD
-obj-y := mux.o
-endif
-
-obj-y += evm.o
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
deleted file mode 100644
index 8ed80d2f4627..000000000000
--- a/board/ti/ti814x/evm.c
+++ /dev/null
@@ -1,190 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * evm.c
- *
- * Board functions for TI814x EVM
- *
- * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
- */
-
-#include <common.h>
-#include <cpsw.h>
-#include <env.h>
-#include <errno.h>
-#include <init.h>
-#include <net.h>
-#include <spl.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/omap.h>
-#include <asm/arch/ddr_defs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/io.h>
-#include <asm/emif.h>
-#include <asm/gpio.h>
-#include "evm.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-
-/* UART Defines */
-#ifdef CONFIG_SPL_BUILD
-static const struct cmd_control evm_ddr2_cctrl_data = {
- .cmd0csratio = 0x80,
- .cmd0iclkout = 0x00,
-
- .cmd1csratio = 0x80,
- .cmd1iclkout = 0x00,
-
- .cmd2csratio = 0x80,
- .cmd2iclkout = 0x00,
-};
-
-static const struct emif_regs evm_ddr2_emif0_regs = {
- .sdram_config = 0x40801ab2,
- .ref_ctrl = 0x10000c30,
- .sdram_tim1 = 0x0aaaf552,
- .sdram_tim2 = 0x043631d2,
- .sdram_tim3 = 0x00000327,
- .emif_ddr_phy_ctlr_1 = 0x00000007
-};
-
-static const struct emif_regs evm_ddr2_emif1_regs = {
- .sdram_config = 0x40801ab2,
- .ref_ctrl = 0x10000c30,
- .sdram_tim1 = 0x0aaaf552,
- .sdram_tim2 = 0x043631d2,
- .sdram_tim3 = 0x00000327,
- .emif_ddr_phy_ctlr_1 = 0x00000007
-};
-
-const struct dmm_lisa_map_regs evm_lisa_map_regs = {
- .dmm_lisa_map_0 = 0x00000000,
- .dmm_lisa_map_1 = 0x00000000,
- .dmm_lisa_map_2 = 0x806c0300,
- .dmm_lisa_map_3 = 0x806c0300,
-};
-
-static const struct ddr_data evm_ddr2_data = {
- .datardsratio0 = ((0x35<<10) | (0x35<<0)),
- .datawdsratio0 = ((0x20<<10) | (0x20<<0)),
- .datawiratio0 = ((0<<10) | (0<<0)),
- .datagiratio0 = ((0<<10) | (0<<0)),
- .datafwsratio0 = ((0x90<<10) | (0x90<<0)),
- .datawrsratio0 = ((0x50<<10) | (0x50<<0)),
-};
-
-void set_uart_mux_conf(void)
-{
- /* Set UART pins */
- enable_uart0_pin_mux();
-}
-
-void set_mux_conf_regs(void)
-{
- /* Set MMC pins */
- enable_mmc1_pin_mux();
-
- /* Set Ethernet pins */
- enable_enet_pin_mux();
-}
-
-void sdram_init(void)
-{
- config_dmm(&evm_lisa_map_regs);
-
- config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
- &evm_ddr2_emif0_regs, 0);
- config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
- &evm_ddr2_emif1_regs, 1);
-}
-#endif
-
-/*
- * Basic board specific setup. Pinmux has been handled already.
- */
-int board_init(void)
-{
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- return 0;
-}
-
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
- omap_mmc_init(1, 0, 0, -1, -1);
-
- return 0;
-}
-#endif
-
-#ifdef CONFIG_DRIVER_TI_CPSW
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
-
- return;
-}
-
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x50,
- .sliver_reg_ofs = 0x700,
- .phy_addr = 1,
- },
- {
- .slave_reg_ofs = 0x90,
- .sliver_reg_ofs = 0x740,
- .phy_addr = 0,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = CPSW_MDIO_BASE,
- .cpsw_base = CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x100,
- .slaves = 1,
- .slave_data = cpsw_slaves,
- .ale_reg_ofs = 0x600,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x28,
- .hw_stats_reg_ofs = 0x400,
- .bd_ram_ofs = 0x2000,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_1,
-};
-#endif
-
-int board_eth_init(bd_t *bis)
-{
- uint8_t mac_addr[6];
- uint32_t mac_hi, mac_lo;
-
- if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
- printf("<ethaddr> not set. Reading from E-fuse\n");
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid0l);
- mac_hi = readl(&cdev->macid0h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
-
- if (is_valid_ethaddr(mac_addr))
- eth_env_set_enetaddr("ethaddr", mac_addr);
- else
- printf("Unable to read MAC address. Set <ethaddr>\n");
- }
-
- return cpsw_register(&cpsw_data);
-}
diff --git a/board/ti/ti814x/evm.h b/board/ti/ti814x/evm.h
deleted file mode 100644
index 6aebec62d4a4..000000000000
--- a/board/ti/ti814x/evm.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#ifndef _EVM_H
-#define _EVM_H
-
-void enable_uart0_pin_mux(void);
-void enable_mmc1_pin_mux(void);
-void enable_enet_pin_mux(void);
-
-#endif /* _EVM_H */
diff --git a/board/ti/ti814x/mux.c b/board/ti/ti814x/mux.c
deleted file mode 100644
index fd9f36451158..000000000000
--- a/board/ti/ti814x/mux.c
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * mux.c
- *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <common.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mux.h>
-#include <asm/io.h>
-#include <i2c.h>
-#include "evm.h"
-
-static struct module_pin_mux uart0_pin_mux[] = {
- {OFFSET(pincntl70), PULLUP_EN | MODE(0x01)}, /* UART0_RXD */
- {OFFSET(pincntl71), PULLUP_EN | MODE(0x01)}, /* UART0_TXD */
- {-1},
-};
-
-static struct module_pin_mux mmc1_pin_mux[] = {
- {OFFSET(pincntl1), PULLUP_EN | MODE(0x01)}, /* SD1_CLK */
- {OFFSET(pincntl2), PULLUP_EN | MODE(0x01)}, /* SD1_CMD */
- {OFFSET(pincntl3), PULLUP_EN | MODE(0x01)}, /* SD1_DAT[0] */
- {OFFSET(pincntl4), PULLUP_EN | MODE(0x01)}, /* SD1_DAT[1] */
- {OFFSET(pincntl5), PULLUP_EN | MODE(0x01)}, /* SD1_DAT[2] */
- {OFFSET(pincntl6), PULLUP_EN | MODE(0x01)}, /* SD1_DAT[3] */
- {OFFSET(pincntl74), PULLUP_EN | MODE(0x40)}, /* SD1_POW */
- {OFFSET(pincntl75), MODE(0x40)}, /* SD1_SDWP */
- {OFFSET(pincntl80), PULLUP_EN | MODE(0x02)}, /* SD1_SDCD */
- {-1},
-};
-
-static struct module_pin_mux enet_pin_mux[] = {
- {OFFSET(pincntl232), MODE(0x01)}, /* EMAC_RMREFCLK */
- {OFFSET(pincntl233), PULLUP_EN | MODE(0x01)}, /* MDCLK */
- {OFFSET(pincntl234), PULLUP_EN | MODE(0x01)}, /* MDIO */
- {OFFSET(pincntl235), MODE(0x01)}, /* EMAC[0]_MTCLK */
- {OFFSET(pincntl236), MODE(0x01)}, /* EMAC[0]_MCOL */
- {OFFSET(pincntl237), MODE(0x01)}, /* EMAC[0]_MCRS */
- {OFFSET(pincntl238), MODE(0x01)}, /* EMAC[0]_MRXER */
- {OFFSET(pincntl239), MODE(0x01)}, /* EMAC[0]_MRCLK */
- {OFFSET(pincntl240), MODE(0x01)}, /* EMAC[0]_MRXD[0] */
- {OFFSET(pincntl241), MODE(0x01)}, /* EMAC[0]_MRXD[1] */
- {OFFSET(pincntl242), MODE(0x01)}, /* EMAC[0]_MRXD[2] */
- {OFFSET(pincntl243), MODE(0x01)}, /* EMAC[0]_MRXD[3] */
- {OFFSET(pincntl244), MODE(0x01)}, /* EMAC[0]_MRXD[4] */
- {OFFSET(pincntl245), MODE(0x01)}, /* EMAC[0]_MRXD[5] */
- {OFFSET(pincntl246), MODE(0x01)}, /* EMAC[0]_MRXD[6] */
- {OFFSET(pincntl247), MODE(0x01)}, /* EMAC[0]_MRXD[7] */
- {OFFSET(pincntl248), MODE(0x01)}, /* EMAC[0]_MRXDV */
- {OFFSET(pincntl249), MODE(0x01)}, /* EMAC[0]_GMTCLK */
- {OFFSET(pincntl250), MODE(0x01)}, /* EMAC[0]_MTXD[0] */
- {OFFSET(pincntl251), MODE(0x01)}, /* EMAC[0]_MTXD[1] */
- {OFFSET(pincntl252), MODE(0x01)}, /* EMAC[0]_MTXD[2] */
- {OFFSET(pincntl253), MODE(0x01)}, /* EMAC[0]_MTXD[3] */
- {OFFSET(pincntl254), MODE(0x01)}, /* EMAC[0]_MTXD[4] */
- {OFFSET(pincntl255), MODE(0x01)}, /* EMAC[0]_MTXD[5] */
- {OFFSET(pincntl256), MODE(0x01)}, /* EMAC[0]_MTXD[6] */
- {OFFSET(pincntl257), MODE(0x01)}, /* EMAC[0]_MTXD[7] */
- {OFFSET(pincntl258), MODE(0x01)}, /* EMAC[0]_MTXEN */
-};
-
-void enable_uart0_pin_mux(void)
-{
- configure_module_pin_mux(uart0_pin_mux);
-}
-
-void enable_mmc1_pin_mux(void)
-{
- configure_module_pin_mux(mmc1_pin_mux);
-}
-
-void enable_enet_pin_mux(void)
-{
- configure_module_pin_mux(enet_pin_mux);
-}
diff --git a/configs/ti814x_evm_defconfig b/configs/ti814x_evm_defconfig
deleted file mode 100644
index 71c9119c7d06..000000000000
--- a/configs/ti814x_evm_defconfig
+++ /dev/null
@@ -1,45 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_TI814X=y
-CONFIG_TARGET_TI814X_EVM=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SPL=y
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_TEXT_BASE=0x40300000
-CONFIG_ENV_VARS_UBOOT_CONFIG=y
-CONFIG_BOOTDELAY=1
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_VERSION_VARIABLE=y
-# CONFIG_DISPLAY_CPUINFO is not set
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-# CONFIG_CMDLINE_EDITING is not set
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_SYS_PROMPT="U-Boot# "
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_MMC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_PHY_ET1011C=y
-CONFIG_MII=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
@ 2020-06-30 17:07 ` Adam Ford
2020-06-30 17:14 ` Tom Rini
2020-06-30 18:49 ` Tom Rini
1 sibling, 1 reply; 12+ messages in thread
From: Adam Ford @ 2020-06-30 17:07 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 11:56 AM Tom Rini <trini@konsulko.com> wrote:
>
> Disable USB support for now. There is non-trivial work required to
> fully move the OMAP3 platforms to DM. While this work is in-progress,
> disable USB support for now as we've gone well past the migration
> deadline.
>
> Cc: Adam Ford <aford173@gmail.com>
> Signed-off-by: Tom Rini <trini@konsulko.com>
> ---
I don't have a beagle, but I have DM_USB working on two different
OMAP3 boards. I am curious to know what's left or what's not working.
adam
> configs/omap3_beagle_defconfig | 20 ++------------------
> 1 file changed, 2 insertions(+), 18 deletions(-)
>
> diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig
> index ed7cb8f2ff63..236a4f4f5f5a 100644
> --- a/configs/omap3_beagle_defconfig
> +++ b/configs/omap3_beagle_defconfig
> @@ -9,6 +9,7 @@ CONFIG_NR_DRAM_BANKS=2
> CONFIG_SPL=y
> CONFIG_SPL_TEXT_BASE=0x40200000
> CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_ANDROID_BOOT_IMAGE=y
> CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
> CONFIG_USE_PREBOOT=y
> CONFIG_PREBOOT="usb start"
> @@ -31,7 +32,6 @@ CONFIG_CMD_MMC=y
> CONFIG_CMD_NAND=y
> CONFIG_CMD_NAND_TRIMFFS=y
> CONFIG_CMD_SPI=y
> -CONFIG_CMD_USB=y
> CONFIG_CMD_CACHE=y
> CONFIG_CMD_EXT4_WRITE=y
> CONFIG_CMD_FS_UUID=y
> @@ -50,8 +50,6 @@ CONFIG_ENV_IS_IN_NAND=y
> CONFIG_SPL_DM=y
> CONFIG_SPL_DM_SEQ_ALIAS=y
> CONFIG_SPL_OF_TRANSLATE=y
> -CONFIG_USB_FUNCTION_FASTBOOT=y
> -CONFIG_FASTBOOT_BUF_ADDR=0x82000000
> CONFIG_LED_STATUS=y
> CONFIG_LED_STATUS0=y
> CONFIG_LED_STATUS_BIT=1
> @@ -73,24 +71,10 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
> CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
> CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
> CONFIG_SPL_NAND_SIMPLE=y
> +CONFIG_DM_ETH=y
> CONFIG_SPI=y
> CONFIG_DM_SPI=y
> CONFIG_OMAP3_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_OMAP3=y
> -CONFIG_USB_MUSB_GADGET=y
> -CONFIG_USB_MUSB_OMAP2PLUS=y
> -CONFIG_TWL4030_USB=y
> -CONFIG_USB_GADGET=y
> -CONFIG_USB_GADGET_MANUFACTURER="TI"
> -CONFIG_USB_GADGET_VENDOR_NUM=0x0451
> -CONFIG_USB_GADGET_PRODUCT_NUM=0xd022
> -CONFIG_USB_ETHER=y
> -CONFIG_USB_HOST_ETHER=y
> -CONFIG_USB_ETHER_ASIX=y
> -CONFIG_USB_ETHER_MCS7830=y
> -CONFIG_USB_ETHER_SMSC95XX=y
> CONFIG_VIDEO_OMAP3=y
> CONFIG_FAT_WRITE=y
> CONFIG_BCH=y
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 17:07 ` Adam Ford
@ 2020-06-30 17:14 ` Tom Rini
2020-06-30 17:35 ` Adam Ford
0 siblings, 1 reply; 12+ messages in thread
From: Tom Rini @ 2020-06-30 17:14 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:07:51PM -0500, Adam Ford wrote:
> On Tue, Jun 30, 2020 at 11:56 AM Tom Rini <trini@konsulko.com> wrote:
> >
> > Disable USB support for now. There is non-trivial work required to
> > fully move the OMAP3 platforms to DM. While this work is in-progress,
> > disable USB support for now as we've gone well past the migration
> > deadline.
> >
> > Cc: Adam Ford <aford173@gmail.com>
> > Signed-off-by: Tom Rini <trini@konsulko.com>
> > ---
>
> I don't have a beagle, but I have DM_USB working on two different
> OMAP3 boards. I am curious to know what's left or what's not working.
Oh? I thought when we talked last there was still more to do to fully
migrate things over. Where should I check again to see what I need to
do on beagle to convert it over? Thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/3eac2728/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 17:14 ` Tom Rini
@ 2020-06-30 17:35 ` Adam Ford
2020-06-30 18:48 ` Tom Rini
0 siblings, 1 reply; 12+ messages in thread
From: Adam Ford @ 2020-06-30 17:35 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:14 PM Tom Rini <trini@konsulko.com> wrote:
>
> On Tue, Jun 30, 2020 at 12:07:51PM -0500, Adam Ford wrote:
> > On Tue, Jun 30, 2020 at 11:56 AM Tom Rini <trini@konsulko.com> wrote:
> > >
> > > Disable USB support for now. There is non-trivial work required to
> > > fully move the OMAP3 platforms to DM. While this work is in-progress,
> > > disable USB support for now as we've gone well past the migration
> > > deadline.
> > >
> > > Cc: Adam Ford <aford173@gmail.com>
> > > Signed-off-by: Tom Rini <trini@konsulko.com>
> > > ---
> >
> > I don't have a beagle, but I have DM_USB working on two different
> > OMAP3 boards. I am curious to know what's left or what's not working.
>
> Oh? I thought when we talked last there was still more to do to fully
> migrate things over. Where should I check again to see what I need to
> do on beagle to convert it over? Thanks!
With [1], the DM support for the EHCI controller was added. There is
still some work to be done to make it better, because there are still
some #defines that need to assign the reset GPIO's. Ideally we'd get
rid of the GPIO defines and use the device tree to address the reset.
It isn't perfect, but it's better than having no USB at all. The
am3517_evm and omap3_logic_somlv have them working. Make sure the
board files have the legacy USB stuff removed [2]
[1] - https://gitlab.denx.de/u-boot/u-boot/-/commit/94ed66194f150c308d1713965a28abce3ac6e200
[2] - https://gitlab.denx.de/u-boot/u-boot/-/commit/76f6d52e61a1968702af69d6cea463b9d9332a96
Let me know if there is anything I can do to help.
adam
>
> --
> Tom
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 17:35 ` Adam Ford
@ 2020-06-30 18:48 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 18:48 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:35:31PM -0500, Adam Ford wrote:
> On Tue, Jun 30, 2020 at 12:14 PM Tom Rini <trini@konsulko.com> wrote:
> >
> > On Tue, Jun 30, 2020 at 12:07:51PM -0500, Adam Ford wrote:
> > > On Tue, Jun 30, 2020 at 11:56 AM Tom Rini <trini@konsulko.com> wrote:
> > > >
> > > > Disable USB support for now. There is non-trivial work required to
> > > > fully move the OMAP3 platforms to DM. While this work is in-progress,
> > > > disable USB support for now as we've gone well past the migration
> > > > deadline.
> > > >
> > > > Cc: Adam Ford <aford173@gmail.com>
> > > > Signed-off-by: Tom Rini <trini@konsulko.com>
> > > > ---
> > >
> > > I don't have a beagle, but I have DM_USB working on two different
> > > OMAP3 boards. I am curious to know what's left or what's not working.
> >
> > Oh? I thought when we talked last there was still more to do to fully
> > migrate things over. Where should I check again to see what I need to
> > do on beagle to convert it over? Thanks!
>
> With [1], the DM support for the EHCI controller was added. There is
> still some work to be done to make it better, because there are still
> some #defines that need to assign the reset GPIO's. Ideally we'd get
> rid of the GPIO defines and use the device tree to address the reset.
> It isn't perfect, but it's better than having no USB at all. The
> am3517_evm and omap3_logic_somlv have them working. Make sure the
> board files have the legacy USB stuff removed [2]
>
> [1] - https://gitlab.denx.de/u-boot/u-boot/-/commit/94ed66194f150c308d1713965a28abce3ac6e200
> [2] - https://gitlab.denx.de/u-boot/u-boot/-/commit/76f6d52e61a1968702af69d6cea463b9d9332a96
>
> Let me know if there is anything I can do to help.
Hunh, thanks. I thought I had tried this much before but had things
blow up. With [2] it's a quick conversion and passing basic sanity
checks. Thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/5c616ad8/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/4] omap3_beagle: Disable USB support
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
2020-06-30 17:07 ` Adam Ford
@ 2020-06-30 18:49 ` Tom Rini
1 sibling, 0 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 18:49 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:56:48PM -0400, Tom Rini wrote:
> Disable USB support for now. There is non-trivial work required to
> fully move the OMAP3 platforms to DM. While this work is in-progress,
> disable USB support for now as we've gone well past the migration
> deadline.
>
> Cc: Adam Ford <aford173@gmail.com>
> Signed-off-by: Tom Rini <trini@konsulko.com>
As Adam noted, I should just convert this instead. It does in fact
convert easily at this point, so I'm rejecting this patch and will post
a conversion instead soon.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/d2186e3f/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/4] am335x: Update list of defconfigs
2020-06-30 16:56 [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
` (2 preceding siblings ...)
2020-06-30 16:56 ` [PATCH 4/4] ti814x: Remove platform Tom Rini
@ 2020-06-30 21:15 ` Tom Rini
3 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 21:15 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:56:47PM -0400, Tom Rini wrote:
> Both the am335x_boneblack and am335x_evm_usbspl configs have been gone
> for a while, remove their entries from MAINTAINERS.
>
> Signed-off-by: Tom Rini <trini@konsulko.com>
Applied to u-boot/next, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/a6839f03/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 3/4] ti816x_evm: Enable DM_MMC
2020-06-30 16:56 ` [PATCH 3/4] ti816x_evm: Enable DM_MMC Tom Rini
@ 2020-06-30 21:15 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 21:15 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:56:49PM -0400, Tom Rini wrote:
> This platform is already using DM in general and the MMC controller is
> the early generation of what is compatible with "ti,omap4-hsmmc" so
> enable DM_MMC (which in turn gets BLK enabled).
>
> Signed-off-by: Tom Rini <trini@konsulko.com>
Applied to u-boot/next, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/46800ee0/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 4/4] ti814x: Remove platform
2020-06-30 16:56 ` [PATCH 4/4] ti814x: Remove platform Tom Rini
@ 2020-06-30 21:15 ` Tom Rini
0 siblings, 0 replies; 12+ messages in thread
From: Tom Rini @ 2020-06-30 21:15 UTC (permalink / raw)
To: u-boot
On Tue, Jun 30, 2020 at 12:56:50PM -0400, Tom Rini wrote:
> The TI814x (DM814x) platform is rather old and in need of a lot of
> migration work. As much of that work is well past the deadline, remove
> this platform.
>
> Signed-off-by: Tom Rini <trini@konsulko.com>
Applied to u-boot/next, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200630/c73bec6e/attachment.sig>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-06-30 21:15 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-30 16:56 [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
2020-06-30 16:56 ` [PATCH 2/4] omap3_beagle: Disable USB support Tom Rini
2020-06-30 17:07 ` Adam Ford
2020-06-30 17:14 ` Tom Rini
2020-06-30 17:35 ` Adam Ford
2020-06-30 18:48 ` Tom Rini
2020-06-30 18:49 ` Tom Rini
2020-06-30 16:56 ` [PATCH 3/4] ti816x_evm: Enable DM_MMC Tom Rini
2020-06-30 21:15 ` Tom Rini
2020-06-30 16:56 ` [PATCH 4/4] ti814x: Remove platform Tom Rini
2020-06-30 21:15 ` Tom Rini
2020-06-30 21:15 ` [PATCH 1/4] am335x: Update list of defconfigs Tom Rini
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.