* [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH
@ 2020-07-01 16:58 Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 01/16] net: fsl_mdio: Change to use virtual address Zhiqiang Hou
` (16 more replies)
0 siblings, 17 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch set depends on:
https://patchwork.ozlabs.org/project/uboot/patch/20200503185227.28731-2-olteanv at gmail.com/
Hou Zhiqiang (16):
net: fsl_mdio: Change to use virtual address
net: fsl_mdio: Correct the MII management register block address
net: tsec: convert to use DM_MDIO when DM_ETH enabled
net: tsec: Add fixed-link PHY support
net: tsec: Add the compatible string "gianfar" support
powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled
fsl: p1_p2_rdb: Move vsc7835 firmware uploading to
board_early_init_r()
configs: p1_p2_rdb: Add the default address of vsc7385 firmware
dts: powerpc: p1020rdb: Add eTSEC DT nodes
powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled
configs: P1020RDB: Enable DM_ETH config
dts: powerpc: p1010rdb: Add eTSEC DT nodes
powerpc: p1010rdb: Compile legacy ethernet init function when no
DM_ETH
configs: P1010RDB: Enable DM_ETH config
dts: powerpc: p2020rdb: Add eTSEC DT nodes
configs: P2020RDB: Enable DM_ETH config
arch/powerpc/cpu/mpc8xxx/cpu.c | 2 +
arch/powerpc/dts/p1010rdb-pa.dts | 1 +
arch/powerpc/dts/p1010rdb-pa_36b.dts | 1 +
arch/powerpc/dts/p1010rdb.dtsi | 50 +++++++++++++++
arch/powerpc/dts/p1010si-post.dtsi | 25 ++++++++
arch/powerpc/dts/p1020-post.dtsi | 20 +++++-
arch/powerpc/dts/p1020rdb-pc.dts | 1 +
arch/powerpc/dts/p1020rdb-pc.dtsi | 55 ++++++++++++++++
arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
arch/powerpc/dts/p1020rdb-pd.dts | 45 ++++++++++++++
arch/powerpc/dts/p2020-post.dtsi | 10 ++-
arch/powerpc/dts/p2020rdb-pc.dts | 1 +
arch/powerpc/dts/p2020rdb-pc.dtsi | 50 +++++++++++++++
arch/powerpc/dts/p2020rdb-pc_36b.dts | 1 +
arch/powerpc/dts/pq3-etsec1-0.dtsi | 28 +++++++++
arch/powerpc/dts/pq3-etsec1-1.dtsi | 28 +++++++++
arch/powerpc/dts/pq3-etsec1-2.dtsi | 28 +++++++++
arch/powerpc/dts/pq3-etsec1-3.dtsi | 28 +++++++++
arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 +++++++++++
arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 +++++++++++
arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 +++++++++++
arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++
arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++
arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++
board/freescale/p1010rdb/p1010rdb.c | 2 +
board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 37 ++++++-----
configs/P1010RDB-PA_36BIT_NAND_defconfig | 2 +
configs/P1010RDB-PA_36BIT_NOR_defconfig | 2 +
configs/P1010RDB-PA_36BIT_SDCARD_defconfig | 2 +
configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig | 2 +
configs/P1010RDB-PA_NAND_defconfig | 2 +
configs/P1010RDB-PA_NOR_defconfig | 2 +
configs/P1010RDB-PA_SDCARD_defconfig | 2 +
configs/P1010RDB-PA_SPIFLASH_defconfig | 2 +
configs/P1010RDB-PB_36BIT_NAND_defconfig | 2 +
configs/P1010RDB-PB_36BIT_NOR_defconfig | 2 +
configs/P1010RDB-PB_36BIT_SDCARD_defconfig | 2 +
configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig | 2 +
configs/P1010RDB-PB_NAND_defconfig | 2 +
configs/P1010RDB-PB_NOR_defconfig | 2 +
configs/P1010RDB-PB_SDCARD_defconfig | 2 +
configs/P1010RDB-PB_SPIFLASH_defconfig | 2 +
configs/P1020RDB-PC_36BIT_NAND_defconfig | 3 +
configs/P1020RDB-PC_36BIT_SDCARD_defconfig | 3 +
configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
configs/P1020RDB-PC_36BIT_defconfig | 3 +
configs/P1020RDB-PC_NAND_defconfig | 3 +
configs/P1020RDB-PC_SDCARD_defconfig | 3 +
configs/P1020RDB-PC_SPIFLASH_defconfig | 3 +
configs/P1020RDB-PC_defconfig | 3 +
configs/P1020RDB-PD_NAND_defconfig | 3 +
configs/P1020RDB-PD_SDCARD_defconfig | 3 +
configs/P1020RDB-PD_SPIFLASH_defconfig | 3 +
configs/P1020RDB-PD_defconfig | 3 +
configs/P2020RDB-PC_36BIT_NAND_defconfig | 3 +
configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 3 +
configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
configs/P2020RDB-PC_36BIT_defconfig | 3 +
configs/P2020RDB-PC_NAND_defconfig | 3 +
configs/P2020RDB-PC_SDCARD_defconfig | 3 +
configs/P2020RDB-PC_SPIFLASH_defconfig | 3 +
configs/P2020RDB-PC_defconfig | 3 +
doc/device-tree-bindings/net/fsl-tsec-phy.txt | 2 +-
drivers/net/fsl_mdio.c | 28 +++++++--
drivers/net/tsec.c | 62 ++++++++-----------
include/configs/p1_p2_rdb_pc.h | 2 +
include/fsl_mdio.h | 4 ++
include/tsec.h | 4 ++
68 files changed, 698 insertions(+), 63 deletions(-)
create mode 100644 arch/powerpc/dts/p1020rdb-pc.dtsi
create mode 100644 arch/powerpc/dts/p2020rdb-pc.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-2.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-3.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 01/16] net: fsl_mdio: Change to use virtual address
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address Zhiqiang Hou
` (15 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
V4:
- No change.
drivers/net/fsl_mdio.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/fsl_mdio.c b/drivers/net/fsl_mdio.c
index 43040d4c3f..e52daa214d 100644
--- a/drivers/net/fsl_mdio.c
+++ b/drivers/net/fsl_mdio.c
@@ -213,7 +213,7 @@ static int tsec_mdio_probe(struct udevice *dev)
printf("dev_get_priv(dev %p) = NULL\n", dev);
return -1;
}
- priv->regs = (void *)(uintptr_t)dev_read_addr(dev);
+ priv->regs = dev_remap_addr(dev);
debug("%s priv %p @ regs %p, pdata %p\n", __func__,
priv, priv->regs, pdata);
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 01/16] net: fsl_mdio: Change to use virtual address Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-04 8:11 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 03/16] net: tsec: convert to use DM_MDIO when DM_ETH enabled Zhiqiang Hou
` (14 subsequent siblings)
16 siblings, 1 reply; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802a9 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
drivers/net/fsl_mdio.c | 28 ++++++++++++++++++++++------
include/fsl_mdio.h | 4 ++++
2 files changed, 26 insertions(+), 6 deletions(-)
diff --git a/drivers/net/fsl_mdio.c b/drivers/net/fsl_mdio.c
index e52daa214d..5b615d50f6 100644
--- a/drivers/net/fsl_mdio.c
+++ b/drivers/net/fsl_mdio.c
@@ -11,6 +11,7 @@
#include <fsl_mdio.h>
#include <asm/io.h>
#include <linux/errno.h>
+#include <tsec.h>
#ifdef CONFIG_DM_MDIO
struct tsec_mdio_priv {
@@ -190,17 +191,30 @@ static const struct mdio_ops tsec_mdio_ops = {
.reset = tsec_mdio_reset,
};
+static struct fsl_pq_mdio_data etsec2_data = {
+ .mdio_regs_off = TSEC_MDIO_REGS_OFFSET,
+};
+
+static struct fsl_pq_mdio_data gianfar_data = {
+ .mdio_regs_off = 0x0,
+};
+
+static struct fsl_pq_mdio_data fman_data = {
+ .mdio_regs_off = 0x0,
+};
+
static const struct udevice_id tsec_mdio_ids[] = {
- { .compatible = "fsl,gianfar-tbi" },
- { .compatible = "fsl,gianfar-mdio" },
- { .compatible = "fsl,etsec2-tbi" },
- { .compatible = "fsl,etsec2-mdio" },
- { .compatible = "fsl,fman-mdio" },
+ { .compatible = "fsl,gianfar-tbi", .data = (ulong)&gianfar_data },
+ { .compatible = "fsl,gianfar-mdio", .data = (ulong)&gianfar_data },
+ { .compatible = "fsl,etsec2-tbi", .data = (ulong)&etsec2_data },
+ { .compatible = "fsl,etsec2-mdio", .data = (ulong)&etsec2_data },
+ { .compatible = "fsl,fman-mdio", .data = (ulong)&fman_data },
{}
};
static int tsec_mdio_probe(struct udevice *dev)
{
+ struct fsl_pq_mdio_data *data;
struct tsec_mdio_priv *priv = (dev) ? dev_get_priv(dev) : NULL;
struct mdio_perdev_priv *pdata = (dev) ? dev_get_uclass_priv(dev) :
NULL;
@@ -213,7 +227,9 @@ static int tsec_mdio_probe(struct udevice *dev)
printf("dev_get_priv(dev %p) = NULL\n", dev);
return -1;
}
- priv->regs = dev_remap_addr(dev);
+
+ data = (struct fsl_pq_mdio_data *)dev_get_driver_data(dev);
+ priv->regs = dev_remap_addr(dev) + data->mdio_regs_off;
debug("%s priv %p @ regs %p, pdata %p\n", __func__,
priv, priv->regs, pdata);
diff --git a/include/fsl_mdio.h b/include/fsl_mdio.h
index 8857d50910..cd612c0954 100644
--- a/include/fsl_mdio.h
+++ b/include/fsl_mdio.h
@@ -55,6 +55,10 @@ int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr,
int regnum);
int memac_mdio_reset(struct mii_dev *bus);
+struct fsl_pq_mdio_data {
+ u32 mdio_regs_off;
+};
+
struct fsl_pq_mdio_info {
struct tsec_mii_mng __iomem *regs;
char *name;
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 03/16] net: tsec: convert to use DM_MDIO when DM_ETH enabled
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 01/16] net: fsl_mdio: Change to use virtual address Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 04/16] net: tsec: Add fixed-link PHY support Zhiqiang Hou
` (13 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- Split the fixed-link PHY support code to a new patch.
drivers/net/tsec.c | 43 ++++++++++---------------------------------
1 file changed, 10 insertions(+), 33 deletions(-)
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index 3d75acb6b4..babe44691e 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -18,6 +18,7 @@
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/errno.h>
+#include <miiphy.h>
#include <asm/processor.h>
#include <asm/io.h>
@@ -681,8 +682,12 @@ static int init_phy(struct tsec_private *priv)
if (priv->interface == PHY_INTERFACE_MODE_SGMII)
tsec_configure_serdes(priv);
+#ifdef CONFIG_DM_ETH
+ phydev = dm_eth_phy_connect(priv->dev);
+#else
phydev = phy_connect(priv->bus, priv->phyaddr, priv->dev,
priv->interface);
+#endif
if (!phydev)
return 0;
@@ -787,14 +792,17 @@ int tsec_standard_init(bd_t *bis)
return tsec_eth_init(bis, tsec_info, ARRAY_SIZE(tsec_info));
}
#else /* CONFIG_DM_ETH */
+
+#ifndef CONFIG_DM_MDIO
+#error "TSEC with DM_ETH also requires DM_MDIO"
+#endif
+
int tsec_probe(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct tsec_private *priv = dev_get_priv(dev);
- struct tsec_mii_mng __iomem *ext_phyregs_mii;
struct ofnode_phandle_args phandle_args;
u32 tbiaddr = CONFIG_SYS_TBIPA_VALUE;
- struct fsl_pq_mdio_info mdio_info;
const char *phy_mode;
fdt_addr_t reg;
ofnode parent;
@@ -803,31 +811,6 @@ int tsec_probe(struct udevice *dev)
pdata->iobase = (phys_addr_t)dev_read_addr(dev);
priv->regs = dev_remap_addr(dev);
- if (dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
- &phandle_args)) {
- printf("phy-handle does not exist under tsec %s\n", dev->name);
- return -ENOENT;
- } else {
- int reg = ofnode_read_u32_default(phandle_args.node, "reg", 0);
-
- priv->phyaddr = reg;
- }
-
- parent = ofnode_get_parent(phandle_args.node);
- if (!ofnode_valid(parent)) {
- printf("No parent node for PHY?\n");
- return -ENOENT;
- }
-
- reg = ofnode_get_addr_index(parent, 0);
- if (reg == FDT_ADDR_T_NONE) {
- printf("No 'reg' property of MII for external PHY\n");
- return -ENOENT;
- }
-
- ext_phyregs_mii = map_physmem(reg + TSEC_MDIO_REGS_OFFSET, 0,
- MAP_NOCACHE);
-
ret = dev_read_phandle_with_args(dev, "tbi-handle", NULL, 0, 0,
&phandle_args);
if (ret == 0) {
@@ -865,12 +848,6 @@ int tsec_probe(struct udevice *dev)
if (priv->interface == PHY_INTERFACE_MODE_SGMII)
priv->flags |= TSEC_SGMII;
- mdio_info.regs = ext_phyregs_mii;
- mdio_info.name = (char *)dev->name;
- ret = fsl_pq_mdio_init(NULL, &mdio_info);
- if (ret)
- return ret;
-
/* Reset the MAC */
setbits_be32(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
udelay(2); /* Soft Reset must be asserted for 3 TX clocks */
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 04/16] net: tsec: Add fixed-link PHY support
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (2 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 03/16] net: tsec: convert to use DM_MDIO when DM_ETH enabled Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 05/16] net: tsec: Add the compatible string "gianfar" support Zhiqiang Hou
` (12 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- New patch.
drivers/net/tsec.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index babe44691e..cb3e56d439 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -683,7 +683,10 @@ static int init_phy(struct tsec_private *priv)
tsec_configure_serdes(priv);
#ifdef CONFIG_DM_ETH
- phydev = dm_eth_phy_connect(priv->dev);
+ if (ofnode_valid(ofnode_find_subnode(priv->dev->node, "fixed-link")))
+ phydev = phy_connect(NULL, 0, priv->dev, priv->interface);
+ else
+ phydev = dm_eth_phy_connect(priv->dev);
#else
phydev = phy_connect(priv->bus, priv->phyaddr, priv->dev,
priv->interface);
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 05/16] net: tsec: Add the compatible string "gianfar" support
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (3 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 04/16] net: tsec: Add fixed-link PHY support Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled Zhiqiang Hou
` (11 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Add compatible string "gianfar" support and update the
device-tree-bindings doc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
V4:
- No change.
doc/device-tree-bindings/net/fsl-tsec-phy.txt | 2 +-
drivers/net/tsec.c | 16 ++++++++++++++--
include/tsec.h | 4 ++++
3 files changed, 19 insertions(+), 3 deletions(-)
diff --git a/doc/device-tree-bindings/net/fsl-tsec-phy.txt b/doc/device-tree-bindings/net/fsl-tsec-phy.txt
index 8e8574bc97..a44c5fd9d9 100644
--- a/doc/device-tree-bindings/net/fsl-tsec-phy.txt
+++ b/doc/device-tree-bindings/net/fsl-tsec-phy.txt
@@ -2,7 +2,7 @@
Properties:
- - compatible : Should be "fsl,etsec2"
+ - compatible : Should be "fsl,etsec2" or "gianfar"
- reg : Offset and length of the register set for the device
- phy-handle : See ethernet.txt file in the same directory.
- phy-connection-type : See ethernet.txt file in the same directory. This
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index cb3e56d439..22658506b2 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -806,11 +806,14 @@ int tsec_probe(struct udevice *dev)
struct tsec_private *priv = dev_get_priv(dev);
struct ofnode_phandle_args phandle_args;
u32 tbiaddr = CONFIG_SYS_TBIPA_VALUE;
+ struct tsec_data *data;
const char *phy_mode;
fdt_addr_t reg;
ofnode parent;
int ret;
+ data = (struct tsec_data *)dev_get_driver_data(dev);
+
pdata->iobase = (phys_addr_t)dev_read_addr(dev);
priv->regs = dev_remap_addr(dev);
@@ -831,7 +834,7 @@ int tsec_probe(struct udevice *dev)
return -ENOENT;
}
- priv->phyregs_sgmii = map_physmem(reg + TSEC_MDIO_REGS_OFFSET,
+ priv->phyregs_sgmii = map_physmem(reg + data->mdio_regs_off,
0, MAP_NOCACHE);
}
@@ -883,8 +886,17 @@ static const struct eth_ops tsec_ops = {
.mcast = tsec_mcast_addr,
};
+static struct tsec_data etsec2_data = {
+ .mdio_regs_off = TSEC_MDIO_REGS_OFFSET,
+};
+
+static struct tsec_data gianfar_data = {
+ .mdio_regs_off = 0x0,
+};
+
static const struct udevice_id tsec_ids[] = {
- { .compatible = "fsl,etsec2" },
+ { .compatible = "fsl,etsec2", .data = (ulong)&etsec2_data },
+ { .compatible = "gianfar", .data = (ulong)&gianfar_data },
{ }
};
diff --git a/include/tsec.h b/include/tsec.h
index b17fa957df..047dd3c373 100644
--- a/include/tsec.h
+++ b/include/tsec.h
@@ -394,6 +394,10 @@ struct tsec {
#define TX_BUF_CNT 2
+struct tsec_data {
+ u32 mdio_regs_off;
+};
+
struct tsec_private {
struct txbd8 __iomem txbd[TX_BUF_CNT];
struct rxbd8 __iomem rxbd[PKTBUFSRX];
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (4 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 05/16] net: tsec: Add the compatible string "gianfar" support Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-04 8:13 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 07/16] fsl: p1_p2_rdb: Move vsc7835 firmware uploading to board_early_init_r() Zhiqiang Hou
` (10 subsequent siblings)
16 siblings, 1 reply; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The cpu_eth_init() is only used by the legacy ethernet driver framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
arch/powerpc/cpu/mpc8xxx/cpu.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index da0a80e6fc..b904943b0e 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -347,6 +347,7 @@ int fixup_cpu(void)
* Initializes on-chip ethernet controllers.
* to override, implement board_eth_init()
*/
+#ifndef CONFIG_DM_ETH
int cpu_eth_init(bd_t *bis)
{
#if defined(CONFIG_ETHER_ON_FCC)
@@ -370,3 +371,4 @@ int cpu_eth_init(bd_t *bis)
#endif
return 0;
}
+#endif
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 07/16] fsl: p1_p2_rdb: Move vsc7835 firmware uploading to board_early_init_r()
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (5 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 08/16] configs: p1_p2_rdb: Add the default address of vsc7385 firmware Zhiqiang Hou
` (9 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Move vsc7835 firmware uploading to board_early_init_r(), so that
the switch also can work in DM eTSEC driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
V4:
- No change.
board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 35 +++++++++++----------
1 file changed, 18 insertions(+), 17 deletions(-)
diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index 1353debc0e..3dd6178708 100644
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -316,6 +316,10 @@ int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
int flash_esel = find_tlb_idx((void *)flashbase, 1);
+#ifdef CONFIG_VSC7385_ENET
+ unsigned int vscfw_addr;
+ char *tmp;
+#endif
/*
* Remap Boot flash region to caching-inhibited
@@ -338,6 +342,20 @@ int board_early_init_r(void)
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,/* perms, wimge */
0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */
+
+#ifdef CONFIG_VSC7385_ENET
+ /* If a VSC7385 microcode image is present, then upload it. */
+ tmp = env_get("vscfw_addr");
+ if (tmp) {
+ vscfw_addr = simple_strtoul(tmp, NULL, 16);
+ printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
+ if (vsc7385_upload_firmware((void *)vscfw_addr,
+ CONFIG_VSC7385_IMAGE_SIZE))
+ puts("Failure uploading VSC7385 microcode.\n");
+ } else {
+ puts("No address specified for VSC7385 microcode.\n");
+ }
+#endif
return 0;
}
@@ -348,10 +366,6 @@ int board_eth_init(bd_t *bis)
ccsr_gur_t *gur __attribute__((unused)) =
(void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
int num = 0;
-#ifdef CONFIG_VSC7385_ENET
- char *tmp;
- unsigned int vscfw_addr;
-#endif
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
@@ -375,19 +389,6 @@ int board_eth_init(bd_t *bis)
return 0;
}
-#ifdef CONFIG_VSC7385_ENET
- /* If a VSC7385 microcode image is present, then upload it. */
- tmp = env_get("vscfw_addr");
- if (tmp) {
- vscfw_addr = simple_strtoul(tmp, NULL, 16);
- printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
- if (vsc7385_upload_firmware((void *) vscfw_addr,
- CONFIG_VSC7385_IMAGE_SIZE))
- puts("Failure uploading VSC7385 microcode.\n");
- } else
- puts("No address specified for VSC7385 microcode.\n");
-#endif
-
mdio_info.regs = TSEC_GET_MDIO_REGS_BASE(1);
mdio_info.name = DEFAULT_MII_NAME;
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 08/16] configs: p1_p2_rdb: Add the default address of vsc7385 firmware
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (6 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 07/16] fsl: p1_p2_rdb: Move vsc7835 firmware uploading to board_early_init_r() Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes Zhiqiang Hou
` (8 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Add the environment 'vscfw_addr' to assign a default address for
vsc7385 firmware uploading.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
include/configs/p1_p2_rdb_pc.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 219e5d216b..6e00491cd8 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -460,6 +460,7 @@
/* Vsc7385 switch */
#ifdef CONFIG_VSC7385_ENET
+#define __VSCFW_ADDR "vscfw_addr=ef000000"
#define CONFIG_SYS_VSC7385_BASE 0xffb00000
#ifdef CONFIG_PHYS_64BIT
@@ -819,6 +820,7 @@ i2c mw 18 3 __SW_BOOT_MASK 1; reset
"ramdisk_size=120000\0" \
"map_lowernorbank=i2c dev 1; i2c mw 18 1 02 1; i2c mw 18 3 fd 1\0" \
"map_uppernorbank=i2c dev 1; i2c mw 18 1 00 1; i2c mw 18 3 fd 1\0" \
+__stringify(__VSCFW_ADDR)"\0" \
__stringify(__NOR_RST_CMD)"\0" \
__stringify(__SPI_RST_CMD)"\0" \
__stringify(__SD_RST_CMD)"\0" \
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (7 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 08/16] configs: p1_p2_rdb: Add the default address of vsc7385 firmware Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-04 8:16 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled Zhiqiang Hou
` (7 subsequent siblings)
16 siblings, 1 reply; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
P1020RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII switch VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- Remove the ptp_clock node.
- Modify the change log slightly.
arch/powerpc/dts/p1020-post.dtsi | 20 ++++++++-
arch/powerpc/dts/p1020rdb-pc.dts | 1 +
arch/powerpc/dts/p1020rdb-pc.dtsi | 55 +++++++++++++++++++++++++
arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
arch/powerpc/dts/p1020rdb-pd.dts | 45 ++++++++++++++++++++
arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 ++++++++++++++++
arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 ++++++++++++++++
arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 ++++++++++++++++
arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++++
arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++++
arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++++
11 files changed, 273 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/dts/p1020rdb-pc.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
diff --git a/arch/powerpc/dts/p1020-post.dtsi b/arch/powerpc/dts/p1020-post.dtsi
index 1dce8e86e9..c73539ad5c 100644
--- a/arch/powerpc/dts/p1020-post.dtsi
+++ b/arch/powerpc/dts/p1020-post.dtsi
@@ -44,10 +44,26 @@
clock-frequency = <0>;
};
- /include/ "pq3-i2c-0.dtsi"
- /include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: enet0_grp2: ethernet at b0000 {
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: enet1_grp2: ethernet at b1000 {
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: enet2_grp2: ethernet at b2000 {
+ };
};
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"
+
/* PCIe controller base address 0x9000 */
&pci1 {
compatible = "fsl,pcie-p1_p2", "fsl,pcie-fsl-qoriq";
diff --git a/arch/powerpc/dts/p1020rdb-pc.dts b/arch/powerpc/dts/p1020rdb-pc.dts
index 7ebaa619df..715330dc50 100644
--- a/arch/powerpc/dts/p1020rdb-pc.dts
+++ b/arch/powerpc/dts/p1020rdb-pc.dts
@@ -32,4 +32,5 @@
};
};
+/include/ "p1020rdb-pc.dtsi"
/include/ "p1020-post.dtsi"
diff --git a/arch/powerpc/dts/p1020rdb-pc.dtsi b/arch/powerpc/dts/p1020rdb-pc.dtsi
new file mode 100644
index 0000000000..6bf424fd3f
--- /dev/null
+++ b/arch/powerpc/dts/p1020rdb-pc.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * P1020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+&soc {
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1 0 0>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1 0 0>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy at 11 {
+ device_type = "tbi-phy";
+ reg = <0x11>;
+ };
+ };
+
+ mdio at 25000 {
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ phy-connection-type = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/dts/p1020rdb-pc_36b.dts b/arch/powerpc/dts/p1020rdb-pc_36b.dts
index c0e5ef4cf4..7680b7c7e1 100644
--- a/arch/powerpc/dts/p1020rdb-pc_36b.dts
+++ b/arch/powerpc/dts/p1020rdb-pc_36b.dts
@@ -32,4 +32,5 @@
};
};
+/include/ "p1020rdb-pc.dtsi"
/include/ "p1020-post.dtsi"
diff --git a/arch/powerpc/dts/p1020rdb-pd.dts b/arch/powerpc/dts/p1020rdb-pd.dts
index 21174a09be..e0e8993dab 100644
--- a/arch/powerpc/dts/p1020rdb-pd.dts
+++ b/arch/powerpc/dts/p1020rdb-pd.dts
@@ -17,6 +17,51 @@
soc: soc at ffe00000 {
ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ interrupts = <3 1 0 0>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupts = <2 1 0 0>;
+ reg = <0x1>;
+ };
+ };
+
+ mdio at 25000 {
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio at 26000 {
+ tbi2: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ phy-connection-type = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
};
pci1: pcie at ffe09000 {
diff --git a/arch/powerpc/dts/pq3-etsec2-0.dtsi b/arch/powerpc/dts/pq3-etsec2-0.dtsi
new file mode 100644
index 0000000000..f9d3d04650
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-0.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 device tree stub [ @ offsets 0x24000/0xb0000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+mdio at 24000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,etsec2-mdio";
+ reg = <0x24000 0x1000 0xb0030 0x4>;
+};
+
+ethernet at b0000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ reg = <0xb0000 0x1000>;
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ ranges;
+
+ queue-group at b0000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb0000 0x1000>;
+ interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/dts/pq3-etsec2-1.dtsi b/arch/powerpc/dts/pq3-etsec2-1.dtsi
new file mode 100644
index 0000000000..6c01481909
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-1.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 device tree stub [ @ offsets 0x25000/0xb1000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+mdio at 25000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,etsec2-tbi";
+ reg = <0x25000 0x1000 0xb1030 0x4>;
+};
+
+ethernet at b1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ reg = <0xb1000 0x1000>;
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ ranges;
+
+ queue-group at b1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb1000 0x1000>;
+ interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/dts/pq3-etsec2-2.dtsi b/arch/powerpc/dts/pq3-etsec2-2.dtsi
new file mode 100644
index 0000000000..2a597c0db6
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-2.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 device tree stub [ @ offsets 0x26000/0xb2000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+mdio at 26000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,etsec2-tbi";
+ reg = <0x26000 0x1000 0xb1030 0x4>;
+};
+
+ethernet at b2000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ reg = <0xb2000 0x1000>;
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ ranges;
+
+ queue-group at b2000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb2000 0x1000>;
+ interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
new file mode 100644
index 0000000000..16752a7c45
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb4000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+&enet0_grp2 {
+ queue-group at b4000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb4000 0x1000>;
+ interrupts = <17 2 0 0 18 2 0 0 24 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
new file mode 100644
index 0000000000..0464938424
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb5000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+&enet1_grp2 {
+ queue-group at b5000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb5000 0x1000>;
+ interrupts = <51 2 0 0 52 2 0 0 67 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
new file mode 100644
index 0000000000..fe8003c44a
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb6000 ]
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+&enet2_grp2 {
+ queue-group at b6000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xb6000 0x1000>;
+ interrupts = <25 2 0 0 26 2 0 0 27 2 0 0>;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (8 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-04 8:36 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 11/16] configs: P1020RDB: Enable DM_ETH config Zhiqiang Hou
` (6 subsequent siblings)
16 siblings, 1 reply; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index 3dd6178708..41585cf342 100644
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -359,6 +359,7 @@ int board_early_init_r(void)
return 0;
}
+#ifndef CONFIG_DM_ETH
int board_eth_init(bd_t *bis)
{
struct fsl_pq_mdio_info mdio_info;
@@ -406,6 +407,7 @@ int board_eth_init(bd_t *bis)
return pci_eth_init(bis);
}
+#endif
#if defined(CONFIG_QE) && \
(defined(CONFIG_TARGET_P1025RDB) || defined(CONFIG_TARGET_P1021RDB))
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 11/16] configs: P1020RDB: Enable DM_ETH config
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (9 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 12/16] dts: powerpc: p1010rdb: Add eTSEC DT nodes Zhiqiang Hou
` (5 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Enable the DM_ETH and DM_MDIO config.
On P1020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
configs/P1020RDB-PC_36BIT_NAND_defconfig | 3 +++
configs/P1020RDB-PC_36BIT_SDCARD_defconfig | 3 +++
configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +++
configs/P1020RDB-PC_36BIT_defconfig | 3 +++
configs/P1020RDB-PC_NAND_defconfig | 3 +++
configs/P1020RDB-PC_SDCARD_defconfig | 3 +++
configs/P1020RDB-PC_SPIFLASH_defconfig | 3 +++
configs/P1020RDB-PC_defconfig | 3 +++
configs/P1020RDB-PD_NAND_defconfig | 3 +++
configs/P1020RDB-PD_SDCARD_defconfig | 3 +++
configs/P1020RDB-PD_SPIFLASH_defconfig | 3 +++
configs/P1020RDB-PD_defconfig | 3 +++
12 files changed, 36 insertions(+)
diff --git a/configs/P1020RDB-PC_36BIT_NAND_defconfig b/configs/P1020RDB-PC_36BIT_NAND_defconfig
index 6ee52fe5e7..139a0be37e 100644
--- a/configs/P1020RDB-PC_36BIT_NAND_defconfig
+++ b/configs/P1020RDB-PC_36BIT_NAND_defconfig
@@ -61,6 +61,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -72,8 +73,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_36BIT_SDCARD_defconfig b/configs/P1020RDB-PC_36BIT_SDCARD_defconfig
index 489b91d8e7..f533225f26 100644
--- a/configs/P1020RDB-PC_36BIT_SDCARD_defconfig
+++ b/configs/P1020RDB-PC_36BIT_SDCARD_defconfig
@@ -56,6 +56,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -67,8 +68,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig b/configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig
index 4a8e4e3726..f3e87f0669 100644
--- a/configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig
+++ b/configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig
@@ -58,6 +58,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -69,8 +70,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_36BIT_defconfig b/configs/P1020RDB-PC_36BIT_defconfig
index f9a4b735ca..04c355585d 100644
--- a/configs/P1020RDB-PC_36BIT_defconfig
+++ b/configs/P1020RDB-PC_36BIT_defconfig
@@ -45,6 +45,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -56,8 +57,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_NAND_defconfig b/configs/P1020RDB-PC_NAND_defconfig
index 5c8231cba2..ee663c5861 100644
--- a/configs/P1020RDB-PC_NAND_defconfig
+++ b/configs/P1020RDB-PC_NAND_defconfig
@@ -60,6 +60,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -71,8 +72,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_SDCARD_defconfig b/configs/P1020RDB-PC_SDCARD_defconfig
index ad2bb90a49..cabd6c6022 100644
--- a/configs/P1020RDB-PC_SDCARD_defconfig
+++ b/configs/P1020RDB-PC_SDCARD_defconfig
@@ -55,6 +55,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -66,8 +67,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_SPIFLASH_defconfig b/configs/P1020RDB-PC_SPIFLASH_defconfig
index b8055e49b0..28a097b0ed 100644
--- a/configs/P1020RDB-PC_SPIFLASH_defconfig
+++ b/configs/P1020RDB-PC_SPIFLASH_defconfig
@@ -57,6 +57,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -68,8 +69,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PC_defconfig b/configs/P1020RDB-PC_defconfig
index a71985374e..580b4ef5c5 100644
--- a/configs/P1020RDB-PC_defconfig
+++ b/configs/P1020RDB-PC_defconfig
@@ -44,6 +44,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -55,8 +56,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PD_NAND_defconfig b/configs/P1020RDB-PD_NAND_defconfig
index 0043fd5f66..f1352d53d5 100644
--- a/configs/P1020RDB-PD_NAND_defconfig
+++ b/configs/P1020RDB-PD_NAND_defconfig
@@ -64,6 +64,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -75,8 +76,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PD_SDCARD_defconfig b/configs/P1020RDB-PD_SDCARD_defconfig
index cb0a8aec65..bba6a0ce95 100644
--- a/configs/P1020RDB-PD_SDCARD_defconfig
+++ b/configs/P1020RDB-PD_SDCARD_defconfig
@@ -59,6 +59,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -70,8 +71,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PD_SPIFLASH_defconfig b/configs/P1020RDB-PD_SPIFLASH_defconfig
index 35e60ca856..3125fa1e9f 100644
--- a/configs/P1020RDB-PD_SPIFLASH_defconfig
+++ b/configs/P1020RDB-PD_SPIFLASH_defconfig
@@ -61,6 +61,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -72,8 +73,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1020RDB-PD_defconfig b/configs/P1020RDB-PD_defconfig
index d7f19c3d96..d3a7afb0b4 100644
--- a/configs/P1020RDB-PD_defconfig
+++ b/configs/P1020RDB-PD_defconfig
@@ -48,6 +48,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -59,8 +60,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 12/16] dts: powerpc: p1010rdb: Add eTSEC DT nodes
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (10 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 11/16] configs: P1020RDB: Enable DM_ETH config Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH Zhiqiang Hou
` (4 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
P1010RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII PHY AR8033
eTSEC2: Connected to SGMII PHY AR8033
eTSEC3: Connected to SGMII PHY AR8033
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- Remove the ptp_clock node.
arch/powerpc/dts/p1010rdb-pa.dts | 1 +
arch/powerpc/dts/p1010rdb-pa_36b.dts | 1 +
arch/powerpc/dts/p1010rdb.dtsi | 50 ++++++++++++++++++++++++++++
arch/powerpc/dts/p1010si-post.dtsi | 25 ++++++++++++++
4 files changed, 77 insertions(+)
diff --git a/arch/powerpc/dts/p1010rdb-pa.dts b/arch/powerpc/dts/p1010rdb-pa.dts
index c66c4923ac..360d254d91 100644
--- a/arch/powerpc/dts/p1010rdb-pa.dts
+++ b/arch/powerpc/dts/p1010rdb-pa.dts
@@ -15,3 +15,4 @@
};
/include/ "p1010si-post.dtsi"
+/include/ "p1010rdb.dtsi"
diff --git a/arch/powerpc/dts/p1010rdb-pa_36b.dts b/arch/powerpc/dts/p1010rdb-pa_36b.dts
index b943de7cbb..062086a8c0 100644
--- a/arch/powerpc/dts/p1010rdb-pa_36b.dts
+++ b/arch/powerpc/dts/p1010rdb-pa_36b.dts
@@ -15,3 +15,4 @@
};
/include/ "p1010si-post.dtsi"
+/include/ "p1010rdb.dtsi"
diff --git a/arch/powerpc/dts/p1010rdb.dtsi b/arch/powerpc/dts/p1010rdb.dtsi
index 4f58ee2446..5964270878 100644
--- a/arch/powerpc/dts/p1010rdb.dtsi
+++ b/arch/powerpc/dts/p1010rdb.dtsi
@@ -5,6 +5,56 @@
* Copyright 2020 NXP
*/
&soc {
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ reg = <0x1>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ reg = <0x0>;
+ };
+
+ phy2: ethernet-phy at 2 {
+ reg = <0x2>;
+ };
+
+ tbi-phy at 3 {
+ device_type = "tbi-phy";
+ reg = <0x3>;
+ };
+ };
+
+ mdio at 25000 {
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio at 26000 {
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy1>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at b2000 {
+ phy-handle = <&phy2>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
i2c at 3000 {
rtc at 68 {
compatible = "pericom,pt7c4338";
diff --git a/arch/powerpc/dts/p1010si-post.dtsi b/arch/powerpc/dts/p1010si-post.dtsi
index 0289441381..f825208056 100644
--- a/arch/powerpc/dts/p1010si-post.dtsi
+++ b/arch/powerpc/dts/p1010si-post.dtsi
@@ -25,6 +25,31 @@
};
/include/ "pq3-i2c-0.dtsi"
/include/ "pq3-i2c-1.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: ethernet at b0000 {
+ queue-group at b0000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: ethernet at b1000 {
+ queue-group at b1000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: ethernet at b2000 {
+ queue-group at b2000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ };
+
+ };
};
/* controller at 0x9000 */
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (11 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 12/16] dts: powerpc: p1010rdb: Add eTSEC DT nodes Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-04 8:38 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 14/16] configs: P1010RDB: Enable DM_ETH config Zhiqiang Hou
` (3 subsequent siblings)
16 siblings, 1 reply; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
board/freescale/p1010rdb/p1010rdb.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c
index 66ccc0bd1e..309f4daa88 100644
--- a/board/freescale/p1010rdb/p1010rdb.c
+++ b/board/freescale/p1010rdb/p1010rdb.c
@@ -484,6 +484,7 @@ int checkboard(void)
return 0;
}
+#ifndef CONFIG_DM_ETH
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_TSEC_ENET
@@ -524,6 +525,7 @@ int board_eth_init(bd_t *bis)
return pci_eth_init(bis);
}
+#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void fdt_del_flexcan(void *blob)
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 14/16] configs: P1010RDB: Enable DM_ETH config
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (12 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 15/16] dts: powerpc: p2020rdb: Add eTSEC DT nodes Zhiqiang Hou
` (2 subsequent siblings)
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Enable the DM_ETH and DM_MDIO config.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- No change.
configs/P1010RDB-PA_36BIT_NAND_defconfig | 2 ++
configs/P1010RDB-PA_36BIT_NOR_defconfig | 2 ++
configs/P1010RDB-PA_36BIT_SDCARD_defconfig | 2 ++
configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig | 2 ++
configs/P1010RDB-PA_NAND_defconfig | 2 ++
configs/P1010RDB-PA_NOR_defconfig | 2 ++
configs/P1010RDB-PA_SDCARD_defconfig | 2 ++
configs/P1010RDB-PA_SPIFLASH_defconfig | 2 ++
configs/P1010RDB-PB_36BIT_NAND_defconfig | 2 ++
configs/P1010RDB-PB_36BIT_NOR_defconfig | 2 ++
configs/P1010RDB-PB_36BIT_SDCARD_defconfig | 2 ++
configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig | 2 ++
configs/P1010RDB-PB_NAND_defconfig | 2 ++
configs/P1010RDB-PB_NOR_defconfig | 2 ++
configs/P1010RDB-PB_SDCARD_defconfig | 2 ++
configs/P1010RDB-PB_SPIFLASH_defconfig | 2 ++
16 files changed, 32 insertions(+)
diff --git a/configs/P1010RDB-PA_36BIT_NAND_defconfig b/configs/P1010RDB-PA_36BIT_NAND_defconfig
index da04cab014..bd31e7c8fa 100644
--- a/configs/P1010RDB-PA_36BIT_NAND_defconfig
+++ b/configs/P1010RDB-PA_36BIT_NAND_defconfig
@@ -72,8 +72,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_36BIT_NOR_defconfig b/configs/P1010RDB-PA_36BIT_NOR_defconfig
index e6edd395e7..f5c5f0ead5 100644
--- a/configs/P1010RDB-PA_36BIT_NOR_defconfig
+++ b/configs/P1010RDB-PA_36BIT_NOR_defconfig
@@ -54,8 +54,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_36BIT_SDCARD_defconfig b/configs/P1010RDB-PA_36BIT_SDCARD_defconfig
index dcd606b0c2..229365a1eb 100644
--- a/configs/P1010RDB-PA_36BIT_SDCARD_defconfig
+++ b/configs/P1010RDB-PA_36BIT_SDCARD_defconfig
@@ -66,8 +66,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig b/configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig
index c0800c8d7d..147198fb88 100644
--- a/configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig
+++ b/configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig
@@ -68,8 +68,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_NAND_defconfig b/configs/P1010RDB-PA_NAND_defconfig
index 29ba692ca1..1f2472a338 100644
--- a/configs/P1010RDB-PA_NAND_defconfig
+++ b/configs/P1010RDB-PA_NAND_defconfig
@@ -71,8 +71,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_NOR_defconfig b/configs/P1010RDB-PA_NOR_defconfig
index d8f87b5dac..35232a87fc 100644
--- a/configs/P1010RDB-PA_NOR_defconfig
+++ b/configs/P1010RDB-PA_NOR_defconfig
@@ -53,8 +53,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_SDCARD_defconfig b/configs/P1010RDB-PA_SDCARD_defconfig
index 9711082529..6a46e3a253 100644
--- a/configs/P1010RDB-PA_SDCARD_defconfig
+++ b/configs/P1010RDB-PA_SDCARD_defconfig
@@ -65,8 +65,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PA_SPIFLASH_defconfig b/configs/P1010RDB-PA_SPIFLASH_defconfig
index de2ac2235f..6c7c12efc1 100644
--- a/configs/P1010RDB-PA_SPIFLASH_defconfig
+++ b/configs/P1010RDB-PA_SPIFLASH_defconfig
@@ -67,8 +67,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_36BIT_NAND_defconfig b/configs/P1010RDB-PB_36BIT_NAND_defconfig
index 9f4876dd13..832f7ce431 100644
--- a/configs/P1010RDB-PB_36BIT_NAND_defconfig
+++ b/configs/P1010RDB-PB_36BIT_NAND_defconfig
@@ -72,8 +72,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_36BIT_NOR_defconfig b/configs/P1010RDB-PB_36BIT_NOR_defconfig
index e85af32e2c..61afaf67ac 100644
--- a/configs/P1010RDB-PB_36BIT_NOR_defconfig
+++ b/configs/P1010RDB-PB_36BIT_NOR_defconfig
@@ -54,8 +54,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_36BIT_SDCARD_defconfig b/configs/P1010RDB-PB_36BIT_SDCARD_defconfig
index 45feab4ee4..8f483b4398 100644
--- a/configs/P1010RDB-PB_36BIT_SDCARD_defconfig
+++ b/configs/P1010RDB-PB_36BIT_SDCARD_defconfig
@@ -66,8 +66,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig b/configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig
index 3cd94f84ea..447ef19530 100644
--- a/configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig
+++ b/configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig
@@ -68,8 +68,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_NAND_defconfig b/configs/P1010RDB-PB_NAND_defconfig
index ddfe7b43a1..d8aae17e84 100644
--- a/configs/P1010RDB-PB_NAND_defconfig
+++ b/configs/P1010RDB-PB_NAND_defconfig
@@ -71,8 +71,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_NOR_defconfig b/configs/P1010RDB-PB_NOR_defconfig
index 6011f8a9d8..632afeaa89 100644
--- a/configs/P1010RDB-PB_NOR_defconfig
+++ b/configs/P1010RDB-PB_NOR_defconfig
@@ -53,8 +53,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_SDCARD_defconfig b/configs/P1010RDB-PB_SDCARD_defconfig
index 65f86fff60..4ba919b206 100644
--- a/configs/P1010RDB-PB_SDCARD_defconfig
+++ b/configs/P1010RDB-PB_SDCARD_defconfig
@@ -65,8 +65,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P1010RDB-PB_SPIFLASH_defconfig b/configs/P1010RDB-PB_SPIFLASH_defconfig
index f71ee19ba6..d5b9aca56d 100644
--- a/configs/P1010RDB-PB_SPIFLASH_defconfig
+++ b/configs/P1010RDB-PB_SPIFLASH_defconfig
@@ -67,8 +67,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 15/16] dts: powerpc: p2020rdb: Add eTSEC DT nodes
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (13 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 14/16] configs: P1010RDB: Enable DM_ETH config Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 16/16] configs: P2020RDB: Enable DM_ETH config Zhiqiang Hou
2020-07-01 17:11 ` [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Vladimir Oltean
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
P2020RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII switch VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
---
V4:
- Remove the ptp_clock node.
- Modify the change log slightly.
arch/powerpc/dts/p2020-post.dtsi | 10 ++++--
arch/powerpc/dts/p2020rdb-pc.dts | 1 +
arch/powerpc/dts/p2020rdb-pc.dtsi | 50 ++++++++++++++++++++++++++++
arch/powerpc/dts/p2020rdb-pc_36b.dts | 1 +
arch/powerpc/dts/pq3-etsec1-0.dtsi | 28 ++++++++++++++++
arch/powerpc/dts/pq3-etsec1-1.dtsi | 28 ++++++++++++++++
arch/powerpc/dts/pq3-etsec1-2.dtsi | 28 ++++++++++++++++
arch/powerpc/dts/pq3-etsec1-3.dtsi | 28 ++++++++++++++++
8 files changed, 172 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/dts/p2020rdb-pc.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-0.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-1.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-2.dtsi
create mode 100644 arch/powerpc/dts/pq3-etsec1-3.dtsi
diff --git a/arch/powerpc/dts/p2020-post.dtsi b/arch/powerpc/dts/p2020-post.dtsi
index 4ed093dad4..f8549b7ddf 100644
--- a/arch/powerpc/dts/p2020-post.dtsi
+++ b/arch/powerpc/dts/p2020-post.dtsi
@@ -38,8 +38,12 @@
clock-frequency = <0>;
};
- /include/ "pq3-i2c-0.dtsi"
- /include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
};
/* PCIe controller base address 0x8000 */
diff --git a/arch/powerpc/dts/p2020rdb-pc.dts b/arch/powerpc/dts/p2020rdb-pc.dts
index 08befd4c59..f3f6be1080 100644
--- a/arch/powerpc/dts/p2020rdb-pc.dts
+++ b/arch/powerpc/dts/p2020rdb-pc.dts
@@ -37,4 +37,5 @@
};
};
+/include/ "p2020rdb-pc.dtsi"
/include/ "p2020-post.dtsi"
diff --git a/arch/powerpc/dts/p2020rdb-pc.dtsi b/arch/powerpc/dts/p2020rdb-pc.dtsi
new file mode 100644
index 0000000000..0d2acc746e
--- /dev/null
+++ b/arch/powerpc/dts/p2020rdb-pc.dtsi
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * P2020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+&soc {
+ mdio at 24520 {
+ phy0: ethernet-phy at 0 {
+ interrupts = <3 1 0 0>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy at 1 {
+ interrupts = <2 1 0 0>;
+ reg = <0x1>;
+ };
+ };
+
+ mdio at 25520 {
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio at 26520 {
+ status = "disabled";
+ };
+
+ enet0: ethernet at 24000 {
+ phy-connection-type = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ enet1: ethernet at 25000 {
+ tbi-handle = <&tbi0>;
+ phy-handle = <&phy0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at 26000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/dts/p2020rdb-pc_36b.dts b/arch/powerpc/dts/p2020rdb-pc_36b.dts
index 04b2519e1a..6d983b7d71 100644
--- a/arch/powerpc/dts/p2020rdb-pc_36b.dts
+++ b/arch/powerpc/dts/p2020rdb-pc_36b.dts
@@ -37,4 +37,5 @@
};
};
+/include/ "p2020rdb-pc.dtsi"
/include/ "p2020-post.dtsi"
diff --git a/arch/powerpc/dts/pq3-etsec1-0.dtsi b/arch/powerpc/dts/pq3-etsec1-0.dtsi
new file mode 100644
index 0000000000..8800243f34
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec1-0.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC device tree stub [ @ offsets 0x24000 ]
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
+};
+
+mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+};
diff --git a/arch/powerpc/dts/pq3-etsec1-1.dtsi b/arch/powerpc/dts/pq3-etsec1-1.dtsi
new file mode 100644
index 0000000000..2bc62d1a57
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec1-1.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC device tree stub [ @ offsets 0x25000 ]
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
+};
+
+mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+};
diff --git a/arch/powerpc/dts/pq3-etsec1-2.dtsi b/arch/powerpc/dts/pq3-etsec1-2.dtsi
new file mode 100644
index 0000000000..d45865fe03
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec1-2.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC device tree stub [ @ offsets 0x26000 ]
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+ethernet at 26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <2>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
+};
+
+mdio at 26520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x26520 0x20>;
+};
diff --git a/arch/powerpc/dts/pq3-etsec1-3.dtsi b/arch/powerpc/dts/pq3-etsec1-3.dtsi
new file mode 100644
index 0000000000..853a27359d
--- /dev/null
+++ b/arch/powerpc/dts/pq3-etsec1-3.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * PQ3 eTSEC device tree stub [ @ offsets 0x27000 ]
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ * Copyright 2020 NXP
+ */
+
+ethernet at 27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <3>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
+ fsl,magic-packet;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <37 2 0 0 38 2 0 0 39 2 0 0>;
+};
+
+mdio at 27520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x27520 0x20>;
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 16/16] configs: P2020RDB: Enable DM_ETH config
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (14 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 15/16] dts: powerpc: p2020rdb: Add eTSEC DT nodes Zhiqiang Hou
@ 2020-07-01 16:58 ` Zhiqiang Hou
2020-07-01 17:11 ` [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Vladimir Oltean
16 siblings, 0 replies; 25+ messages in thread
From: Zhiqiang Hou @ 2020-07-01 16:58 UTC (permalink / raw)
To: u-boot
From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Enable the DM_ETH and DM_MDIO config.
On P2020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
V4:
- No change.
configs/P2020RDB-PC_36BIT_NAND_defconfig | 3 +++
configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 3 +++
configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +++
configs/P2020RDB-PC_36BIT_defconfig | 3 +++
configs/P2020RDB-PC_NAND_defconfig | 3 +++
configs/P2020RDB-PC_SDCARD_defconfig | 3 +++
configs/P2020RDB-PC_SPIFLASH_defconfig | 3 +++
configs/P2020RDB-PC_defconfig | 3 +++
8 files changed, 24 insertions(+)
diff --git a/configs/P2020RDB-PC_36BIT_NAND_defconfig b/configs/P2020RDB-PC_36BIT_NAND_defconfig
index 3e6ea64ee3..4cd689f55d 100644
--- a/configs/P2020RDB-PC_36BIT_NAND_defconfig
+++ b/configs/P2020RDB-PC_36BIT_NAND_defconfig
@@ -66,6 +66,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -77,8 +78,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_36BIT_SDCARD_defconfig b/configs/P2020RDB-PC_36BIT_SDCARD_defconfig
index 187cbee0d6..f46463a297 100644
--- a/configs/P2020RDB-PC_36BIT_SDCARD_defconfig
+++ b/configs/P2020RDB-PC_36BIT_SDCARD_defconfig
@@ -61,6 +61,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -72,8 +73,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig b/configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig
index 88c9224001..73d1be1013 100644
--- a/configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig
+++ b/configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig
@@ -63,6 +63,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -74,8 +75,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_36BIT_defconfig b/configs/P2020RDB-PC_36BIT_defconfig
index 88e24c30ba..21a0e85f98 100644
--- a/configs/P2020RDB-PC_36BIT_defconfig
+++ b/configs/P2020RDB-PC_36BIT_defconfig
@@ -50,6 +50,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -61,8 +62,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_NAND_defconfig b/configs/P2020RDB-PC_NAND_defconfig
index dda34dd43e..800c728ed3 100644
--- a/configs/P2020RDB-PC_NAND_defconfig
+++ b/configs/P2020RDB-PC_NAND_defconfig
@@ -65,6 +65,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -76,8 +77,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_SDCARD_defconfig b/configs/P2020RDB-PC_SDCARD_defconfig
index c2b6ad5f32..81cbac2fe8 100644
--- a/configs/P2020RDB-PC_SDCARD_defconfig
+++ b/configs/P2020RDB-PC_SDCARD_defconfig
@@ -60,6 +60,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -71,8 +72,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_SPIFLASH_defconfig b/configs/P2020RDB-PC_SPIFLASH_defconfig
index 3ec208ee00..89308a503b 100644
--- a/configs/P2020RDB-PC_SPIFLASH_defconfig
+++ b/configs/P2020RDB-PC_SPIFLASH_defconfig
@@ -62,6 +62,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -73,8 +74,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
diff --git a/configs/P2020RDB-PC_defconfig b/configs/P2020RDB-PC_defconfig
index 0f0a6ad810..66fc3b0a14 100644
--- a/configs/P2020RDB-PC_defconfig
+++ b/configs/P2020RDB-PC_defconfig
@@ -49,6 +49,7 @@ CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_BROADCOM=y
CONFIG_PHY_DAVICOM=y
@@ -60,8 +61,10 @@ CONFIG_PHY_SMSC=y
CONFIG_PHY_VITESSE=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_DM_ETH=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
+CONFIG_DM_MDIO=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_FSL=y
--
2.25.1
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
` (15 preceding siblings ...)
2020-07-01 16:58 ` [PATCHv4 16/16] configs: P2020RDB: Enable DM_ETH config Zhiqiang Hou
@ 2020-07-01 17:11 ` Vladimir Oltean
2020-07-01 17:45 ` Vladimir Oltean
16 siblings, 1 reply; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-01 17:11 UTC (permalink / raw)
To: u-boot
Hi Zhiqiang,
On Wed, 1 Jul 2020 at 20:05, Zhiqiang Hou <Zhiqiang.Hou@nxp.com> wrote:
>
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> This patch set depends on:
> https://patchwork.ozlabs.org/project/uboot/patch/20200503185227.28731-2-olteanv at gmail.com/
>
> Hou Zhiqiang (16):
> net: fsl_mdio: Change to use virtual address
> net: fsl_mdio: Correct the MII management register block address
> net: tsec: convert to use DM_MDIO when DM_ETH enabled
> net: tsec: Add fixed-link PHY support
> net: tsec: Add the compatible string "gianfar" support
> powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled
> fsl: p1_p2_rdb: Move vsc7835 firmware uploading to
> board_early_init_r()
> configs: p1_p2_rdb: Add the default address of vsc7385 firmware
> dts: powerpc: p1020rdb: Add eTSEC DT nodes
> powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled
> configs: P1020RDB: Enable DM_ETH config
> dts: powerpc: p1010rdb: Add eTSEC DT nodes
> powerpc: p1010rdb: Compile legacy ethernet init function when no
> DM_ETH
> configs: P1010RDB: Enable DM_ETH config
> dts: powerpc: p2020rdb: Add eTSEC DT nodes
> configs: P2020RDB: Enable DM_ETH config
>
> arch/powerpc/cpu/mpc8xxx/cpu.c | 2 +
> arch/powerpc/dts/p1010rdb-pa.dts | 1 +
> arch/powerpc/dts/p1010rdb-pa_36b.dts | 1 +
> arch/powerpc/dts/p1010rdb.dtsi | 50 +++++++++++++++
> arch/powerpc/dts/p1010si-post.dtsi | 25 ++++++++
> arch/powerpc/dts/p1020-post.dtsi | 20 +++++-
> arch/powerpc/dts/p1020rdb-pc.dts | 1 +
> arch/powerpc/dts/p1020rdb-pc.dtsi | 55 ++++++++++++++++
> arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
> arch/powerpc/dts/p1020rdb-pd.dts | 45 ++++++++++++++
> arch/powerpc/dts/p2020-post.dtsi | 10 ++-
> arch/powerpc/dts/p2020rdb-pc.dts | 1 +
> arch/powerpc/dts/p2020rdb-pc.dtsi | 50 +++++++++++++++
> arch/powerpc/dts/p2020rdb-pc_36b.dts | 1 +
> arch/powerpc/dts/pq3-etsec1-0.dtsi | 28 +++++++++
> arch/powerpc/dts/pq3-etsec1-1.dtsi | 28 +++++++++
> arch/powerpc/dts/pq3-etsec1-2.dtsi | 28 +++++++++
> arch/powerpc/dts/pq3-etsec1-3.dtsi | 28 +++++++++
> arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 +++++++++++
> arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 +++++++++++
> arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 +++++++++++
> arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++
> arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++
> arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++
> board/freescale/p1010rdb/p1010rdb.c | 2 +
> board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 37 ++++++-----
> configs/P1010RDB-PA_36BIT_NAND_defconfig | 2 +
> configs/P1010RDB-PA_36BIT_NOR_defconfig | 2 +
> configs/P1010RDB-PA_36BIT_SDCARD_defconfig | 2 +
> configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig | 2 +
> configs/P1010RDB-PA_NAND_defconfig | 2 +
> configs/P1010RDB-PA_NOR_defconfig | 2 +
> configs/P1010RDB-PA_SDCARD_defconfig | 2 +
> configs/P1010RDB-PA_SPIFLASH_defconfig | 2 +
> configs/P1010RDB-PB_36BIT_NAND_defconfig | 2 +
> configs/P1010RDB-PB_36BIT_NOR_defconfig | 2 +
> configs/P1010RDB-PB_36BIT_SDCARD_defconfig | 2 +
> configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig | 2 +
> configs/P1010RDB-PB_NAND_defconfig | 2 +
> configs/P1010RDB-PB_NOR_defconfig | 2 +
> configs/P1010RDB-PB_SDCARD_defconfig | 2 +
> configs/P1010RDB-PB_SPIFLASH_defconfig | 2 +
> configs/P1020RDB-PC_36BIT_NAND_defconfig | 3 +
> configs/P1020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> configs/P1020RDB-PC_36BIT_defconfig | 3 +
> configs/P1020RDB-PC_NAND_defconfig | 3 +
> configs/P1020RDB-PC_SDCARD_defconfig | 3 +
> configs/P1020RDB-PC_SPIFLASH_defconfig | 3 +
> configs/P1020RDB-PC_defconfig | 3 +
> configs/P1020RDB-PD_NAND_defconfig | 3 +
> configs/P1020RDB-PD_SDCARD_defconfig | 3 +
> configs/P1020RDB-PD_SPIFLASH_defconfig | 3 +
> configs/P1020RDB-PD_defconfig | 3 +
> configs/P2020RDB-PC_36BIT_NAND_defconfig | 3 +
> configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> configs/P2020RDB-PC_36BIT_defconfig | 3 +
> configs/P2020RDB-PC_NAND_defconfig | 3 +
> configs/P2020RDB-PC_SDCARD_defconfig | 3 +
> configs/P2020RDB-PC_SPIFLASH_defconfig | 3 +
> configs/P2020RDB-PC_defconfig | 3 +
> doc/device-tree-bindings/net/fsl-tsec-phy.txt | 2 +-
> drivers/net/fsl_mdio.c | 28 +++++++--
> drivers/net/tsec.c | 62 ++++++++-----------
> include/configs/p1_p2_rdb_pc.h | 2 +
> include/fsl_mdio.h | 4 ++
> include/tsec.h | 4 ++
> 68 files changed, 698 insertions(+), 63 deletions(-)
> create mode 100644 arch/powerpc/dts/p1020rdb-pc.dtsi
> create mode 100644 arch/powerpc/dts/p2020rdb-pc.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec1-0.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec1-1.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec1-2.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec1-3.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
>
> --
> 2.25.1
>
The point with the Acked-by/Reviewed-by/Tested-by tags is that you
copy them to your next patch submissions, such that the maintainers
see which patches have had eyes on them already, so that they don't
need to look through them again.
Thanks,
-Vladimir
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH
2020-07-01 17:11 ` [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Vladimir Oltean
@ 2020-07-01 17:45 ` Vladimir Oltean
2020-07-02 2:09 ` Z.q. Hou
0 siblings, 1 reply; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-01 17:45 UTC (permalink / raw)
To: u-boot
On Wed, 1 Jul 2020 at 20:11, Vladimir Oltean <olteanv@gmail.com> wrote:
>
> Hi Zhiqiang,
>
> On Wed, 1 Jul 2020 at 20:05, Zhiqiang Hou <Zhiqiang.Hou@nxp.com> wrote:
> >
> > From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> >
> > This patch set depends on:
> > https://patchwork.ozlabs.org/project/uboot/patch/20200503185227.28731-2-olteanv at gmail.com/
> >
> > Hou Zhiqiang (16):
> > net: fsl_mdio: Change to use virtual address
> > net: fsl_mdio: Correct the MII management register block address
> > net: tsec: convert to use DM_MDIO when DM_ETH enabled
> > net: tsec: Add fixed-link PHY support
> > net: tsec: Add the compatible string "gianfar" support
> > powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled
> > fsl: p1_p2_rdb: Move vsc7835 firmware uploading to
> > board_early_init_r()
> > configs: p1_p2_rdb: Add the default address of vsc7385 firmware
> > dts: powerpc: p1020rdb: Add eTSEC DT nodes
> > powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled
> > configs: P1020RDB: Enable DM_ETH config
> > dts: powerpc: p1010rdb: Add eTSEC DT nodes
> > powerpc: p1010rdb: Compile legacy ethernet init function when no
> > DM_ETH
> > configs: P1010RDB: Enable DM_ETH config
> > dts: powerpc: p2020rdb: Add eTSEC DT nodes
> > configs: P2020RDB: Enable DM_ETH config
> >
> > arch/powerpc/cpu/mpc8xxx/cpu.c | 2 +
> > arch/powerpc/dts/p1010rdb-pa.dts | 1 +
> > arch/powerpc/dts/p1010rdb-pa_36b.dts | 1 +
> > arch/powerpc/dts/p1010rdb.dtsi | 50 +++++++++++++++
> > arch/powerpc/dts/p1010si-post.dtsi | 25 ++++++++
> > arch/powerpc/dts/p1020-post.dtsi | 20 +++++-
> > arch/powerpc/dts/p1020rdb-pc.dts | 1 +
> > arch/powerpc/dts/p1020rdb-pc.dtsi | 55 ++++++++++++++++
> > arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
> > arch/powerpc/dts/p1020rdb-pd.dts | 45 ++++++++++++++
> > arch/powerpc/dts/p2020-post.dtsi | 10 ++-
> > arch/powerpc/dts/p2020rdb-pc.dts | 1 +
> > arch/powerpc/dts/p2020rdb-pc.dtsi | 50 +++++++++++++++
> > arch/powerpc/dts/p2020rdb-pc_36b.dts | 1 +
> > arch/powerpc/dts/pq3-etsec1-0.dtsi | 28 +++++++++
> > arch/powerpc/dts/pq3-etsec1-1.dtsi | 28 +++++++++
> > arch/powerpc/dts/pq3-etsec1-2.dtsi | 28 +++++++++
> > arch/powerpc/dts/pq3-etsec1-3.dtsi | 28 +++++++++
> > arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 +++++++++++
> > arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 +++++++++++
> > arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 +++++++++++
> > arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++
> > arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++
> > arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++
> > board/freescale/p1010rdb/p1010rdb.c | 2 +
> > board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 37 ++++++-----
> > configs/P1010RDB-PA_36BIT_NAND_defconfig | 2 +
> > configs/P1010RDB-PA_36BIT_NOR_defconfig | 2 +
> > configs/P1010RDB-PA_36BIT_SDCARD_defconfig | 2 +
> > configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig | 2 +
> > configs/P1010RDB-PA_NAND_defconfig | 2 +
> > configs/P1010RDB-PA_NOR_defconfig | 2 +
> > configs/P1010RDB-PA_SDCARD_defconfig | 2 +
> > configs/P1010RDB-PA_SPIFLASH_defconfig | 2 +
> > configs/P1010RDB-PB_36BIT_NAND_defconfig | 2 +
> > configs/P1010RDB-PB_36BIT_NOR_defconfig | 2 +
> > configs/P1010RDB-PB_36BIT_SDCARD_defconfig | 2 +
> > configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig | 2 +
> > configs/P1010RDB-PB_NAND_defconfig | 2 +
> > configs/P1010RDB-PB_NOR_defconfig | 2 +
> > configs/P1010RDB-PB_SDCARD_defconfig | 2 +
> > configs/P1010RDB-PB_SPIFLASH_defconfig | 2 +
> > configs/P1020RDB-PC_36BIT_NAND_defconfig | 3 +
> > configs/P1020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> > configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> > configs/P1020RDB-PC_36BIT_defconfig | 3 +
> > configs/P1020RDB-PC_NAND_defconfig | 3 +
> > configs/P1020RDB-PC_SDCARD_defconfig | 3 +
> > configs/P1020RDB-PC_SPIFLASH_defconfig | 3 +
> > configs/P1020RDB-PC_defconfig | 3 +
> > configs/P1020RDB-PD_NAND_defconfig | 3 +
> > configs/P1020RDB-PD_SDCARD_defconfig | 3 +
> > configs/P1020RDB-PD_SPIFLASH_defconfig | 3 +
> > configs/P1020RDB-PD_defconfig | 3 +
> > configs/P2020RDB-PC_36BIT_NAND_defconfig | 3 +
> > configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> > configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> > configs/P2020RDB-PC_36BIT_defconfig | 3 +
> > configs/P2020RDB-PC_NAND_defconfig | 3 +
> > configs/P2020RDB-PC_SDCARD_defconfig | 3 +
> > configs/P2020RDB-PC_SPIFLASH_defconfig | 3 +
> > configs/P2020RDB-PC_defconfig | 3 +
> > doc/device-tree-bindings/net/fsl-tsec-phy.txt | 2 +-
> > drivers/net/fsl_mdio.c | 28 +++++++--
> > drivers/net/tsec.c | 62 ++++++++-----------
> > include/configs/p1_p2_rdb_pc.h | 2 +
> > include/fsl_mdio.h | 4 ++
> > include/tsec.h | 4 ++
> > 68 files changed, 698 insertions(+), 63 deletions(-)
> > create mode 100644 arch/powerpc/dts/p1020rdb-pc.dtsi
> > create mode 100644 arch/powerpc/dts/p2020rdb-pc.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec1-0.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec1-1.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec1-2.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec1-3.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
> >
> > --
> > 2.25.1
> >
>
> The point with the Acked-by/Reviewed-by/Tested-by tags is that you
> copy them to your next patch submissions, such that the maintainers
> see which patches have had eyes on them already, so that they don't
> need to look through them again.
>
> Thanks,
> -Vladimir
I'm sorry, please ignore this. I thought none of the patches have the
Reviewed-by tag I added, but looks like those are in fact all the
patches that I did review. Time to review the rest!
Thanks,
-Vladimir
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH
2020-07-01 17:45 ` Vladimir Oltean
@ 2020-07-02 2:09 ` Z.q. Hou
0 siblings, 0 replies; 25+ messages in thread
From: Z.q. Hou @ 2020-07-02 2:09 UTC (permalink / raw)
To: u-boot
Hi Vladimir,
Thanks a lot for your comments!
> -----Original Message-----
> From: Vladimir Oltean [mailto:olteanv at gmail.com]
> Sent: 2020?7?2? 1:46
> To: Z.q. Hou <zhiqiang.hou@nxp.com>
> Cc: u-boot <u-boot@lists.denx.de>; Bin Meng <bmeng.cn@gmail.com>;
> Priyanka Jain <priyanka.jain@nxp.com>
> Subject: Re: [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB
> board to DM_ETH
>
> On Wed, 1 Jul 2020 at 20:11, Vladimir Oltean <olteanv@gmail.com> wrote:
> >
> > Hi Zhiqiang,
> >
> > On Wed, 1 Jul 2020 at 20:05, Zhiqiang Hou <Zhiqiang.Hou@nxp.com> wrote:
> > >
> > > From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> > >
> > > This patch set depends on:
> > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpa
> > >
> tchwork.ozlabs.org%2Fproject%2Fuboot%2Fpatch%2F20200503185227.2873
> 1-
> > >
> 2-olteanv%40gmail.com%2F&data=02%7C01%7CZhiqiang.Hou%40nxp.c
> om%7
> > >
> C9215a1fed74348210eb108d81de69d85%7C686ea1d3bc2b4c6fa92cd99c5c3
> 01635
> > > %7C0%7C0%7C637292223605570364&sdata=s1fe6AFATwaeeUAOU
> gK7vMElVZNP
> > > 3L%2F62pDsdcfOE%2BY%3D&reserved=0
> > >
> > > Hou Zhiqiang (16):
> > > net: fsl_mdio: Change to use virtual address
> > > net: fsl_mdio: Correct the MII management register block address
> > > net: tsec: convert to use DM_MDIO when DM_ETH enabled
> > > net: tsec: Add fixed-link PHY support
> > > net: tsec: Add the compatible string "gianfar" support
> > > powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH
> enabled
> > > fsl: p1_p2_rdb: Move vsc7835 firmware uploading to
> > > board_early_init_r()
> > > configs: p1_p2_rdb: Add the default address of vsc7385 firmware
> > > dts: powerpc: p1020rdb: Add eTSEC DT nodes
> > > powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH
> enabled
> > > configs: P1020RDB: Enable DM_ETH config
> > > dts: powerpc: p1010rdb: Add eTSEC DT nodes
> > > powerpc: p1010rdb: Compile legacy ethernet init function when no
> > > DM_ETH
> > > configs: P1010RDB: Enable DM_ETH config
> > > dts: powerpc: p2020rdb: Add eTSEC DT nodes
> > > configs: P2020RDB: Enable DM_ETH config
> > >
> > > arch/powerpc/cpu/mpc8xxx/cpu.c | 2 +
> > > arch/powerpc/dts/p1010rdb-pa.dts | 1 +
> > > arch/powerpc/dts/p1010rdb-pa_36b.dts | 1 +
> > > arch/powerpc/dts/p1010rdb.dtsi | 50
> +++++++++++++++
> > > arch/powerpc/dts/p1010si-post.dtsi | 25 ++++++++
> > > arch/powerpc/dts/p1020-post.dtsi | 20 +++++-
> > > arch/powerpc/dts/p1020rdb-pc.dts | 1 +
> > > arch/powerpc/dts/p1020rdb-pc.dtsi | 55
> ++++++++++++++++
> > > arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
> > > arch/powerpc/dts/p1020rdb-pd.dts | 45
> ++++++++++++++
> > > arch/powerpc/dts/p2020-post.dtsi | 10 ++-
> > > arch/powerpc/dts/p2020rdb-pc.dts | 1 +
> > > arch/powerpc/dts/p2020rdb-pc.dtsi | 50
> +++++++++++++++
> > > arch/powerpc/dts/p2020rdb-pc_36b.dts | 1 +
> > > arch/powerpc/dts/pq3-etsec1-0.dtsi | 28 +++++++++
> > > arch/powerpc/dts/pq3-etsec1-1.dtsi | 28 +++++++++
> > > arch/powerpc/dts/pq3-etsec1-2.dtsi | 28 +++++++++
> > > arch/powerpc/dts/pq3-etsec1-3.dtsi | 28 +++++++++
> > > arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 +++++++++++
> > > arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 +++++++++++
> > > arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 +++++++++++
> > > arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++
> > > arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++
> > > arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++
> > > board/freescale/p1010rdb/p1010rdb.c | 2 +
> > > board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 37 ++++++-----
> > > configs/P1010RDB-PA_36BIT_NAND_defconfig | 2 +
> > > configs/P1010RDB-PA_36BIT_NOR_defconfig | 2 +
> > > configs/P1010RDB-PA_36BIT_SDCARD_defconfig | 2 +
> > > configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig | 2 +
> > > configs/P1010RDB-PA_NAND_defconfig | 2 +
> > > configs/P1010RDB-PA_NOR_defconfig | 2 +
> > > configs/P1010RDB-PA_SDCARD_defconfig | 2 +
> > > configs/P1010RDB-PA_SPIFLASH_defconfig | 2 +
> > > configs/P1010RDB-PB_36BIT_NAND_defconfig | 2 +
> > > configs/P1010RDB-PB_36BIT_NOR_defconfig | 2 +
> > > configs/P1010RDB-PB_36BIT_SDCARD_defconfig | 2 +
> > > configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig | 2 +
> > > configs/P1010RDB-PB_NAND_defconfig | 2 +
> > > configs/P1010RDB-PB_NOR_defconfig | 2 +
> > > configs/P1010RDB-PB_SDCARD_defconfig | 2 +
> > > configs/P1010RDB-PB_SPIFLASH_defconfig | 2 +
> > > configs/P1020RDB-PC_36BIT_NAND_defconfig | 3 +
> > > configs/P1020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> > > configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> > > configs/P1020RDB-PC_36BIT_defconfig | 3 +
> > > configs/P1020RDB-PC_NAND_defconfig | 3 +
> > > configs/P1020RDB-PC_SDCARD_defconfig | 3 +
> > > configs/P1020RDB-PC_SPIFLASH_defconfig | 3 +
> > > configs/P1020RDB-PC_defconfig | 3 +
> > > configs/P1020RDB-PD_NAND_defconfig | 3 +
> > > configs/P1020RDB-PD_SDCARD_defconfig | 3 +
> > > configs/P1020RDB-PD_SPIFLASH_defconfig | 3 +
> > > configs/P1020RDB-PD_defconfig | 3 +
> > > configs/P2020RDB-PC_36BIT_NAND_defconfig | 3 +
> > > configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 3 +
> > > configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 3 +
> > > configs/P2020RDB-PC_36BIT_defconfig | 3 +
> > > configs/P2020RDB-PC_NAND_defconfig | 3 +
> > > configs/P2020RDB-PC_SDCARD_defconfig | 3 +
> > > configs/P2020RDB-PC_SPIFLASH_defconfig | 3 +
> > > configs/P2020RDB-PC_defconfig | 3 +
> > > doc/device-tree-bindings/net/fsl-tsec-phy.txt | 2 +-
> > > drivers/net/fsl_mdio.c | 28 +++++++--
> > > drivers/net/tsec.c | 62
> ++++++++-----------
> > > include/configs/p1_p2_rdb_pc.h | 2 +
> > > include/fsl_mdio.h | 4 ++
> > > include/tsec.h | 4 ++
> > > 68 files changed, 698 insertions(+), 63 deletions(-) create mode
> > > 100644 arch/powerpc/dts/p1020rdb-pc.dtsi create mode 100644
> > > arch/powerpc/dts/p2020rdb-pc.dtsi create mode 100644
> > > arch/powerpc/dts/pq3-etsec1-0.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec1-1.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec1-2.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec1-3.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> > > create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
> > >
> > > --
> > > 2.25.1
> > >
> >
> > The point with the Acked-by/Reviewed-by/Tested-by tags is that you
> > copy them to your next patch submissions, such that the maintainers
> > see which patches have had eyes on them already, so that they don't
> > need to look through them again.
> >
> > Thanks,
> > -Vladimir
>
> I'm sorry, please ignore this. I thought none of the patches have the
> Reviewed-by tag I added, but looks like those are in fact all the patches that I
> did review. Time to review the rest!
That's all right, and thanks again!
Regards,
Zhiqiang
>
> Thanks,
> -Vladimir
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address
2020-07-01 16:58 ` [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address Zhiqiang Hou
@ 2020-07-04 8:11 ` Vladimir Oltean
0 siblings, 0 replies; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-04 8:11 UTC (permalink / raw)
To: u-boot
On Thu, Jul 02, 2020 at 12:58:43AM +0800, Zhiqiang Hou wrote:
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> The MII management register block offset is different between
> gianfar and etsec2 compatible devices, this patch is to fix
> this issue by adding driver data for different compatible
> string.
>
> Fixes: 2932c5a802a9 ("net: tsec: fsl_mdio: add DM MDIO support")
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> V4:
> - No change.
>
> drivers/net/fsl_mdio.c | 28 ++++++++++++++++++++++------
> include/fsl_mdio.h | 4 ++++
> 2 files changed, 26 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/fsl_mdio.c b/drivers/net/fsl_mdio.c
> index e52daa214d..5b615d50f6 100644
> --- a/drivers/net/fsl_mdio.c
> +++ b/drivers/net/fsl_mdio.c
> @@ -11,6 +11,7 @@
> #include <fsl_mdio.h>
> #include <asm/io.h>
> #include <linux/errno.h>
> +#include <tsec.h>
>
> #ifdef CONFIG_DM_MDIO
> struct tsec_mdio_priv {
> @@ -190,17 +191,30 @@ static const struct mdio_ops tsec_mdio_ops = {
> .reset = tsec_mdio_reset,
> };
>
> +static struct fsl_pq_mdio_data etsec2_data = {
> + .mdio_regs_off = TSEC_MDIO_REGS_OFFSET,
> +};
> +
> +static struct fsl_pq_mdio_data gianfar_data = {
> + .mdio_regs_off = 0x0,
> +};
> +
> +static struct fsl_pq_mdio_data fman_data = {
> + .mdio_regs_off = 0x0,
> +};
> +
> static const struct udevice_id tsec_mdio_ids[] = {
> - { .compatible = "fsl,gianfar-tbi" },
> - { .compatible = "fsl,gianfar-mdio" },
> - { .compatible = "fsl,etsec2-tbi" },
> - { .compatible = "fsl,etsec2-mdio" },
> - { .compatible = "fsl,fman-mdio" },
> + { .compatible = "fsl,gianfar-tbi", .data = (ulong)&gianfar_data },
> + { .compatible = "fsl,gianfar-mdio", .data = (ulong)&gianfar_data },
> + { .compatible = "fsl,etsec2-tbi", .data = (ulong)&etsec2_data },
> + { .compatible = "fsl,etsec2-mdio", .data = (ulong)&etsec2_data },
> + { .compatible = "fsl,fman-mdio", .data = (ulong)&fman_data },
> {}
> };
>
> static int tsec_mdio_probe(struct udevice *dev)
> {
> + struct fsl_pq_mdio_data *data;
> struct tsec_mdio_priv *priv = (dev) ? dev_get_priv(dev) : NULL;
> struct mdio_perdev_priv *pdata = (dev) ? dev_get_uclass_priv(dev) :
> NULL;
> @@ -213,7 +227,9 @@ static int tsec_mdio_probe(struct udevice *dev)
> printf("dev_get_priv(dev %p) = NULL\n", dev);
> return -1;
> }
> - priv->regs = dev_remap_addr(dev);
> +
> + data = (struct fsl_pq_mdio_data *)dev_get_driver_data(dev);
> + priv->regs = dev_remap_addr(dev) + data->mdio_regs_off;
> debug("%s priv %p @ regs %p, pdata %p\n", __func__,
> priv, priv->regs, pdata);
>
> diff --git a/include/fsl_mdio.h b/include/fsl_mdio.h
> index 8857d50910..cd612c0954 100644
> --- a/include/fsl_mdio.h
> +++ b/include/fsl_mdio.h
> @@ -55,6 +55,10 @@ int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr,
> int regnum);
> int memac_mdio_reset(struct mii_dev *bus);
>
> +struct fsl_pq_mdio_data {
> + u32 mdio_regs_off;
> +};
> +
> struct fsl_pq_mdio_info {
> struct tsec_mii_mng __iomem *regs;
> char *name;
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled
2020-07-01 16:58 ` [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled Zhiqiang Hou
@ 2020-07-04 8:13 ` Vladimir Oltean
0 siblings, 0 replies; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-04 8:13 UTC (permalink / raw)
To: u-boot
On Thu, Jul 02, 2020 at 12:58:47AM +0800, Zhiqiang Hou wrote:
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> The cpu_eth_init() is only used by the legacy ethernet driver framework.
>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> V4:
> - No change.
>
> arch/powerpc/cpu/mpc8xxx/cpu.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
> index da0a80e6fc..b904943b0e 100644
> --- a/arch/powerpc/cpu/mpc8xxx/cpu.c
> +++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
> @@ -347,6 +347,7 @@ int fixup_cpu(void)
> * Initializes on-chip ethernet controllers.
> * to override, implement board_eth_init()
> */
> +#ifndef CONFIG_DM_ETH
> int cpu_eth_init(bd_t *bis)
> {
> #if defined(CONFIG_ETHER_ON_FCC)
> @@ -370,3 +371,4 @@ int cpu_eth_init(bd_t *bis)
> #endif
> return 0;
> }
> +#endif
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes
2020-07-01 16:58 ` [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes Zhiqiang Hou
@ 2020-07-04 8:16 ` Vladimir Oltean
0 siblings, 0 replies; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-04 8:16 UTC (permalink / raw)
To: u-boot
On Thu, Jul 02, 2020 at 12:58:50AM +0800, Zhiqiang Hou wrote:
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> P1020RDB implements 3 enhanced three-speed Ethernet controllers,
> and the connection is shown below:
> eTSEC1: Connected to RGMII switch VSC7385
> eTSEC2: Connected to SGMII PHY VSC8221
> eTSEC3: Connected to SGMII PHY AR8021
>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> V4:
> - Remove the ptp_clock node.
> - Modify the change log slightly.
>
> arch/powerpc/dts/p1020-post.dtsi | 20 ++++++++-
> arch/powerpc/dts/p1020rdb-pc.dts | 1 +
> arch/powerpc/dts/p1020rdb-pc.dtsi | 55 +++++++++++++++++++++++++
> arch/powerpc/dts/p1020rdb-pc_36b.dts | 1 +
> arch/powerpc/dts/p1020rdb-pd.dts | 45 ++++++++++++++++++++
> arch/powerpc/dts/pq3-etsec2-0.dtsi | 35 ++++++++++++++++
> arch/powerpc/dts/pq3-etsec2-1.dtsi | 35 ++++++++++++++++
> arch/powerpc/dts/pq3-etsec2-2.dtsi | 35 ++++++++++++++++
> arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi | 16 +++++++
> arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi | 16 +++++++
> arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi | 16 +++++++
> 11 files changed, 273 insertions(+), 2 deletions(-)
> create mode 100644 arch/powerpc/dts/p1020rdb-pc.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-0.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-1.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-2.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> create mode 100644 arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
>
> diff --git a/arch/powerpc/dts/p1020-post.dtsi b/arch/powerpc/dts/p1020-post.dtsi
> index 1dce8e86e9..c73539ad5c 100644
> --- a/arch/powerpc/dts/p1020-post.dtsi
> +++ b/arch/powerpc/dts/p1020-post.dtsi
> @@ -44,10 +44,26 @@
> clock-frequency = <0>;
> };
>
> - /include/ "pq3-i2c-0.dtsi"
> - /include/ "pq3-i2c-1.dtsi"
> +/include/ "pq3-i2c-0.dtsi"
> +/include/ "pq3-i2c-1.dtsi"
> +
> +/include/ "pq3-etsec2-0.dtsi"
> + enet0: enet0_grp2: ethernet at b0000 {
> + };
> +
> +/include/ "pq3-etsec2-1.dtsi"
> + enet1: enet1_grp2: ethernet at b1000 {
> + };
> +
> +/include/ "pq3-etsec2-2.dtsi"
> + enet2: enet2_grp2: ethernet at b2000 {
> + };
> };
>
> +/include/ "pq3-etsec2-grp2-0.dtsi"
> +/include/ "pq3-etsec2-grp2-1.dtsi"
> +/include/ "pq3-etsec2-grp2-2.dtsi"
> +
> /* PCIe controller base address 0x9000 */
> &pci1 {
> compatible = "fsl,pcie-p1_p2", "fsl,pcie-fsl-qoriq";
> diff --git a/arch/powerpc/dts/p1020rdb-pc.dts b/arch/powerpc/dts/p1020rdb-pc.dts
> index 7ebaa619df..715330dc50 100644
> --- a/arch/powerpc/dts/p1020rdb-pc.dts
> +++ b/arch/powerpc/dts/p1020rdb-pc.dts
> @@ -32,4 +32,5 @@
> };
> };
>
> +/include/ "p1020rdb-pc.dtsi"
> /include/ "p1020-post.dtsi"
> diff --git a/arch/powerpc/dts/p1020rdb-pc.dtsi b/arch/powerpc/dts/p1020rdb-pc.dtsi
> new file mode 100644
> index 0000000000..6bf424fd3f
> --- /dev/null
> +++ b/arch/powerpc/dts/p1020rdb-pc.dtsi
> @@ -0,0 +1,55 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * P1020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
> + *
> + * Copyright 2012 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +&soc {
> + mdio at 24000 {
> + phy0: ethernet-phy at 0 {
> + interrupt-parent = <&mpic>;
> + interrupts = <3 1 0 0>;
> + reg = <0x0>;
> + };
> +
> + phy1: ethernet-phy at 1 {
> + interrupt-parent = <&mpic>;
> + interrupts = <2 1 0 0>;
> + reg = <0x1>;
> + };
> +
> + tbi0: tbi-phy at 11 {
> + device_type = "tbi-phy";
> + reg = <0x11>;
> + };
> + };
> +
> + mdio at 25000 {
> + tbi1: tbi-phy at 11 {
> + reg = <0x11>;
> + device_type = "tbi-phy";
> + };
> + };
> +
> + enet0: ethernet at b0000 {
> + phy-connection-type = "rgmii-id";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +
> + };
> +
> + enet1: ethernet at b1000 {
> + phy-handle = <&phy0>;
> + tbi-handle = <&tbi1>;
> + phy-connection-type = "sgmii";
> + };
> +
> + enet2: ethernet at b2000 {
> + phy-handle = <&phy1>;
> + phy-connection-type = "rgmii-id";
> + };
> +};
> diff --git a/arch/powerpc/dts/p1020rdb-pc_36b.dts b/arch/powerpc/dts/p1020rdb-pc_36b.dts
> index c0e5ef4cf4..7680b7c7e1 100644
> --- a/arch/powerpc/dts/p1020rdb-pc_36b.dts
> +++ b/arch/powerpc/dts/p1020rdb-pc_36b.dts
> @@ -32,4 +32,5 @@
> };
> };
>
> +/include/ "p1020rdb-pc.dtsi"
> /include/ "p1020-post.dtsi"
> diff --git a/arch/powerpc/dts/p1020rdb-pd.dts b/arch/powerpc/dts/p1020rdb-pd.dts
> index 21174a09be..e0e8993dab 100644
> --- a/arch/powerpc/dts/p1020rdb-pd.dts
> +++ b/arch/powerpc/dts/p1020rdb-pd.dts
> @@ -17,6 +17,51 @@
>
> soc: soc at ffe00000 {
> ranges = <0x0 0x0 0xffe00000 0x100000>;
> +
> + mdio at 24000 {
> + phy0: ethernet-phy at 0 {
> + interrupts = <3 1 0 0>;
> + reg = <0x0>;
> + };
> +
> + phy1: ethernet-phy at 1 {
> + interrupts = <2 1 0 0>;
> + reg = <0x1>;
> + };
> + };
> +
> + mdio at 25000 {
> + tbi1: tbi-phy at 11 {
> + reg = <0x11>;
> + device_type = "tbi-phy";
> + };
> + };
> +
> + mdio at 26000 {
> + tbi2: tbi-phy at 11 {
> + reg = <0x11>;
> + device_type = "tbi-phy";
> + };
> + };
> +
> + enet0: ethernet at b0000 {
> + phy-connection-type = "rgmii-id";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + enet1: ethernet at b1000 {
> + phy-handle = <&phy0>;
> + tbi-handle = <&tbi1>;
> + phy-connection-type = "sgmii";
> + };
> +
> + enet2: ethernet at b2000 {
> + phy-handle = <&phy1>;
> + phy-connection-type = "rgmii-id";
> + };
> };
>
> pci1: pcie at ffe09000 {
> diff --git a/arch/powerpc/dts/pq3-etsec2-0.dtsi b/arch/powerpc/dts/pq3-etsec2-0.dtsi
> new file mode 100644
> index 0000000000..f9d3d04650
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-0.dtsi
> @@ -0,0 +1,35 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 device tree stub [ @ offsets 0x24000/0xb0000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +mdio at 24000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,etsec2-mdio";
> + reg = <0x24000 0x1000 0xb0030 0x4>;
> +};
> +
> +ethernet at b0000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "network";
> + model = "eTSEC";
> + compatible = "fsl,etsec2";
> + reg = <0xb0000 0x1000>;
> + fsl,num_rx_queues = <0x8>;
> + fsl,num_tx_queues = <0x8>;
> + fsl,magic-packet;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + ranges;
> +
> + queue-group at b0000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb0000 0x1000>;
> + interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
> + };
> +};
> diff --git a/arch/powerpc/dts/pq3-etsec2-1.dtsi b/arch/powerpc/dts/pq3-etsec2-1.dtsi
> new file mode 100644
> index 0000000000..6c01481909
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-1.dtsi
> @@ -0,0 +1,35 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 device tree stub [ @ offsets 0x25000/0xb1000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +mdio at 25000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,etsec2-tbi";
> + reg = <0x25000 0x1000 0xb1030 0x4>;
> +};
> +
> +ethernet at b1000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "network";
> + model = "eTSEC";
> + compatible = "fsl,etsec2";
> + reg = <0xb1000 0x1000>;
> + fsl,num_rx_queues = <0x8>;
> + fsl,num_tx_queues = <0x8>;
> + fsl,magic-packet;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + ranges;
> +
> + queue-group at b1000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb1000 0x1000>;
> + interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
> + };
> +};
> diff --git a/arch/powerpc/dts/pq3-etsec2-2.dtsi b/arch/powerpc/dts/pq3-etsec2-2.dtsi
> new file mode 100644
> index 0000000000..2a597c0db6
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-2.dtsi
> @@ -0,0 +1,35 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 device tree stub [ @ offsets 0x26000/0xb2000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +mdio at 26000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,etsec2-tbi";
> + reg = <0x26000 0x1000 0xb1030 0x4>;
> +};
> +
> +ethernet at b2000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "network";
> + model = "eTSEC";
> + compatible = "fsl,etsec2";
> + reg = <0xb2000 0x1000>;
> + fsl,num_rx_queues = <0x8>;
> + fsl,num_tx_queues = <0x8>;
> + fsl,magic-packet;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + ranges;
> +
> + queue-group at b2000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb2000 0x1000>;
> + interrupts = <31 2 0 0 32 2 0 0 33 2 0 0>;
> + };
> +};
> diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> new file mode 100644
> index 0000000000..16752a7c45
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-grp2-0.dtsi
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb4000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +&enet0_grp2 {
> + queue-group at b4000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb4000 0x1000>;
> + interrupts = <17 2 0 0 18 2 0 0 24 2 0 0>;
> + };
> +};
> diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> new file mode 100644
> index 0000000000..0464938424
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-grp2-1.dtsi
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb5000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +&enet1_grp2 {
> + queue-group at b5000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb5000 0x1000>;
> + interrupts = <51 2 0 0 52 2 0 0 67 2 0 0>;
> + };
> +};
> diff --git a/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi b/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
> new file mode 100644
> index 0000000000..fe8003c44a
> --- /dev/null
> +++ b/arch/powerpc/dts/pq3-etsec2-grp2-2.dtsi
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR X11
> +/*
> + * PQ3 eTSEC2 Group 2 device tree stub [ @ offsets 0xb6000 ]
> + *
> + * Copyright 2011 Freescale Semiconductor Inc.
> + * Copyright 2020 NXP
> + */
> +
> +&enet2_grp2 {
> + queue-group at b6000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xb6000 0x1000>;
> + interrupts = <25 2 0 0 26 2 0 0 27 2 0 0>;
> + };
> +};
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled
2020-07-01 16:58 ` [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled Zhiqiang Hou
@ 2020-07-04 8:36 ` Vladimir Oltean
0 siblings, 0 replies; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-04 8:36 UTC (permalink / raw)
To: u-boot
On Thu, Jul 02, 2020 at 12:58:51AM +0800, Zhiqiang Hou wrote:
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> The board_eth_init() is only used by legacy ethernet driver framework,
> so do not compile it when DM_ETH config has been selected.
>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> V4:
> - No change.
>
> board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
> index 3dd6178708..41585cf342 100644
> --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
> +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
> @@ -359,6 +359,7 @@ int board_early_init_r(void)
> return 0;
> }
>
> +#ifndef CONFIG_DM_ETH
> int board_eth_init(bd_t *bis)
> {
> struct fsl_pq_mdio_info mdio_info;
> @@ -406,6 +407,7 @@ int board_eth_init(bd_t *bis)
>
> return pci_eth_init(bis);
> }
> +#endif
>
> #if defined(CONFIG_QE) && \
> (defined(CONFIG_TARGET_P1025RDB) || defined(CONFIG_TARGET_P1021RDB))
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH
2020-07-01 16:58 ` [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH Zhiqiang Hou
@ 2020-07-04 8:38 ` Vladimir Oltean
0 siblings, 0 replies; 25+ messages in thread
From: Vladimir Oltean @ 2020-07-04 8:38 UTC (permalink / raw)
To: u-boot
On Thu, Jul 02, 2020 at 12:58:54AM +0800, Zhiqiang Hou wrote:
> From: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
>
> The board_eth_init() is only used by legacy ethernet driver framework,
> so do not compile it when DM_ETH config has been selected.
>
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> V4:
> - No change.
>
> board/freescale/p1010rdb/p1010rdb.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c
> index 66ccc0bd1e..309f4daa88 100644
> --- a/board/freescale/p1010rdb/p1010rdb.c
> +++ b/board/freescale/p1010rdb/p1010rdb.c
> @@ -484,6 +484,7 @@ int checkboard(void)
> return 0;
> }
>
> +#ifndef CONFIG_DM_ETH
> int board_eth_init(bd_t *bis)
> {
> #ifdef CONFIG_TSEC_ENET
> @@ -524,6 +525,7 @@ int board_eth_init(bd_t *bis)
>
> return pci_eth_init(bis);
> }
> +#endif
>
> #if defined(CONFIG_OF_BOARD_SETUP)
> void fdt_del_flexcan(void *blob)
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 25+ messages in thread
end of thread, other threads:[~2020-07-04 8:38 UTC | newest]
Thread overview: 25+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-01 16:58 [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 01/16] net: fsl_mdio: Change to use virtual address Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 02/16] net: fsl_mdio: Correct the MII management register block address Zhiqiang Hou
2020-07-04 8:11 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 03/16] net: tsec: convert to use DM_MDIO when DM_ETH enabled Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 04/16] net: tsec: Add fixed-link PHY support Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 05/16] net: tsec: Add the compatible string "gianfar" support Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 06/16] powerpc: mpc8xxx: Don't compile cpu_eth_init() when DM_ETH enabled Zhiqiang Hou
2020-07-04 8:13 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 07/16] fsl: p1_p2_rdb: Move vsc7835 firmware uploading to board_early_init_r() Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 08/16] configs: p1_p2_rdb: Add the default address of vsc7385 firmware Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 09/16] dts: powerpc: p1020rdb: Add eTSEC DT nodes Zhiqiang Hou
2020-07-04 8:16 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 10/16] powerpc: p1_p2_rdb: Don't compile board_eth_init() when DM_ETH enabled Zhiqiang Hou
2020-07-04 8:36 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 11/16] configs: P1020RDB: Enable DM_ETH config Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 12/16] dts: powerpc: p1010rdb: Add eTSEC DT nodes Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 13/16] powerpc: p1010rdb: Compile legacy ethernet init function when no DM_ETH Zhiqiang Hou
2020-07-04 8:38 ` Vladimir Oltean
2020-07-01 16:58 ` [PATCHv4 14/16] configs: P1010RDB: Enable DM_ETH config Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 15/16] dts: powerpc: p2020rdb: Add eTSEC DT nodes Zhiqiang Hou
2020-07-01 16:58 ` [PATCHv4 16/16] configs: P2020RDB: Enable DM_ETH config Zhiqiang Hou
2020-07-01 17:11 ` [PATCHv4 00/16] powerpc: covert p1010, p1020 and p2020 RDB board to DM_ETH Vladimir Oltean
2020-07-01 17:45 ` Vladimir Oltean
2020-07-02 2:09 ` Z.q. Hou
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.