From: Jim Quinlan <james.quinlan@broadcom.com> To: linux-pci@vger.kernel.org, Nicolas Saenz Julienne <nsaenzjulienne@suse.de>, bcm-kernel-feedback-list@broadcom.com, james.quinlan@broadcom.com Cc: Jim Quinlan <james.quinlan@broadcom.com>, Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>, Rob Herring <robh@kernel.org>, Bjorn Helgaas <bhelgaas@google.com>, Florian Fainelli <f.fainelli@gmail.com>, linux-rpi-kernel@lists.infradead.org (moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE), linux-arm-kernel@lists.infradead.org (moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE), linux-kernel@vger.kernel.org (open list) Subject: [PATCH v7 06/12] PCI: brcmstb: Add bcm7278 PERST# support Date: Wed, 8 Jul 2020 15:31:59 -0400 [thread overview] Message-ID: <20200708193219.47134-7-james.quinlan@broadcom.com> (raw) In-Reply-To: <20200708193219.47134-1-james.quinlan@broadcom.com> From: Jim Quinlan <jquinlan@broadcom.com> The PERST# bit was moved to a different register in 7278-type STB chips. In addition, the polarity of the bit was also changed; for other chips writing a 1 specified assert; for 7278-type chips, writing a 0 specifies assert. Of course, PERST# is a PCIe asserted-low signal. Signed-off-by: Jim Quinlan <jquinlan@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> --- drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c index 7c148eb65170..e5e7f7d82eda 100644 --- a/drivers/pci/controller/pcie-brcmstb.c +++ b/drivers/pci/controller/pcie-brcmstb.c @@ -83,6 +83,7 @@ #define PCIE_MISC_PCIE_CTRL 0x4064 #define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1 +#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK 0x4 #define PCIE_MISC_PCIE_STATUS 0x4068 #define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80 @@ -685,9 +686,16 @@ static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val) { u32 tmp; - tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); - u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); - writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + if (pcie->type == BCM7278) { + /* Perst bit has moved and assert value is 0 */ + tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL); + u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK); + writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL); + } else { + tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); + writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + } } static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie, @@ -772,7 +780,10 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie) /* Reset the bridge */ brcm_pcie_bridge_sw_init_set(pcie, 1); - brcm_pcie_perst_set(pcie, 1); + + /* BCM7278 fails when PERST# is set here */ + if (pcie->type != BCM7278) + brcm_pcie_perst_set(pcie, 1); usleep_range(100, 200); -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Jim Quinlan <james.quinlan@broadcom.com> To: linux-pci@vger.kernel.org, Nicolas Saenz Julienne <nsaenzjulienne@suse.de>, bcm-kernel-feedback-list@broadcom.com, james.quinlan@broadcom.com Cc: Rob Herring <robh@kernel.org>, Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>, open list <linux-kernel@vger.kernel.org>, Florian Fainelli <f.fainelli@gmail.com>, "moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE" <linux-rpi-kernel@lists.infradead.org>, Jim Quinlan <james.quinlan@broadcom.com>, Bjorn Helgaas <bhelgaas@google.com>, "moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE" <linux-arm-kernel@lists.infradead.org> Subject: [PATCH v7 06/12] PCI: brcmstb: Add bcm7278 PERST# support Date: Wed, 8 Jul 2020 15:31:59 -0400 [thread overview] Message-ID: <20200708193219.47134-7-james.quinlan@broadcom.com> (raw) In-Reply-To: <20200708193219.47134-1-james.quinlan@broadcom.com> From: Jim Quinlan <jquinlan@broadcom.com> The PERST# bit was moved to a different register in 7278-type STB chips. In addition, the polarity of the bit was also changed; for other chips writing a 1 specified assert; for 7278-type chips, writing a 0 specifies assert. Of course, PERST# is a PCIe asserted-low signal. Signed-off-by: Jim Quinlan <jquinlan@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> --- drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c index 7c148eb65170..e5e7f7d82eda 100644 --- a/drivers/pci/controller/pcie-brcmstb.c +++ b/drivers/pci/controller/pcie-brcmstb.c @@ -83,6 +83,7 @@ #define PCIE_MISC_PCIE_CTRL 0x4064 #define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1 +#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK 0x4 #define PCIE_MISC_PCIE_STATUS 0x4068 #define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80 @@ -685,9 +686,16 @@ static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val) { u32 tmp; - tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); - u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); - writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + if (pcie->type == BCM7278) { + /* Perst bit has moved and assert value is 0 */ + tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL); + u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK); + writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL); + } else { + tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); + writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie)); + } } static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie, @@ -772,7 +780,10 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie) /* Reset the bridge */ brcm_pcie_bridge_sw_init_set(pcie, 1); - brcm_pcie_perst_set(pcie, 1); + + /* BCM7278 fails when PERST# is set here */ + if (pcie->type != BCM7278) + brcm_pcie_perst_set(pcie, 1); usleep_range(100, 200); -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-07-08 19:32 UTC|newest] Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-07-08 19:31 [PATCH v7 00/12] PCI: brcmstb: enable PCIe for STB chips Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan via iommu 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` [PATCH v7 01/12] PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB Jim Quinlan 2020-07-08 19:31 ` [PATCH v7 02/12] ata: ahci_brcm: Fix use of BCM7216 reset controller Jim Quinlan 2020-07-08 19:31 ` [PATCH v7 03/12] dt-bindings: PCI: Add bindings for more Brcmstb chips Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` [PATCH v7 04/12] PCI: brcmstb: Add bcm7278 register info Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` [PATCH v7 05/12] PCI: brcmstb: Add suspend and resume pm_ops Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan 2020-07-08 19:31 ` Jim Quinlan [this message] 2020-07-08 19:31 ` [PATCH v7 06/12] PCI: brcmstb: Add bcm7278 PERST# support Jim Quinlan 2020-07-08 19:32 ` [PATCH v7 07/12] PCI: brcmstb: Add control of rescal reset Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan 2020-07-08 19:32 ` [PATCH v7 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan via iommu 2020-07-09 10:31 ` Christoph Hellwig 2020-07-09 10:31 ` Christoph Hellwig 2020-07-09 13:27 ` Jim Quinlan 2020-07-09 13:27 ` Jim Quinlan 2020-07-09 13:27 ` Jim Quinlan via iommu 2020-07-09 13:30 ` Christoph Hellwig 2020-07-09 13:30 ` Christoph Hellwig 2020-07-11 8:40 ` kernel test robot 2020-07-11 8:40 ` kernel test robot 2020-07-11 8:40 ` kernel test robot 2020-07-08 19:32 ` [PATCH v7 09/12] PCI: brcmstb: Set additional internal memory DMA viewport sizes Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan 2020-07-08 19:32 ` [PATCH v7 10/12] PCI: brcmstb: Accommodate MSI for older chips Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan 2020-07-08 19:32 ` [PATCH v7 11/12] PCI: brcmstb: Set bus max burst size by chip type Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan 2020-07-08 19:32 ` [PATCH v7 12/12] PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list Jim Quinlan 2020-07-08 19:32 ` Jim Quinlan
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200708193219.47134-7-james.quinlan@broadcom.com \ --to=james.quinlan@broadcom.com \ --cc=bcm-kernel-feedback-list@broadcom.com \ --cc=bhelgaas@google.com \ --cc=f.fainelli@gmail.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-pci@vger.kernel.org \ --cc=linux-rpi-kernel@lists.infradead.org \ --cc=lorenzo.pieralisi@arm.com \ --cc=nsaenzjulienne@suse.de \ --cc=robh@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.