[PATCH v3 00/14] Enable GPU for SM8150 and SM8250

[PATCH v3 00/14] Enable GPU for SM8150 and SM8250

[Jonathan Marek]

This series adds the missing clock drivers and dts nodes to enable
the GPU on both SM8150 and SM8250.

Note an extra drm/msm patch [1] is required for SM8250.

As noted by Dmitry, GMU init fails with newer firmware, needs this patch [2].

[1] https://patchwork.freedesktop.org/series/78968/
[2] https://git.linaro.org/landing-teams/working/qualcomm/kernel.git/commit/?h=tracking-qcomlt-sm8250&id=01331f2ccbe7e6c4719dbe038a5fb496db32646d

Changes in V2:
* Added "clk: qcom: gcc: fix sm8150 GPU and NPU clocks" to fix the newly added
  SM8150 GPU gcc clocks
* Added "Fixes:" tag to "clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL"
* Added yaml schemas to gpucc dt-bindings patches
* Added "clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers" and changed
  gpucc patches to use it.
* Removed CLK_IS_CRITICAL from gpu_cc_ahb_clk
* Added missing rpmh regulator level for sm8250 GPU clock levels
* Use sm8150/sm8250 iommu compatibles in dts
* Add gcc_gpu_gpll0_clk_src/gcc_gpu_gpll0_div_clk_src to gpucc clocks in dts

Changes in V3:
* Combined gpucc yaml bindings into one
* Removed some unused clocks from gpucc drivers to move closely match other gpucc
* Use parent_data instead of parent_names

Jonathan Marek (14):
  clk: qcom: gcc: fix sm8150 GPU and NPU clocks
  clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL
  clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid
  clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll
  clk: qcom: gcc: remove unnecessary vco_table from SM8150
  dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc
  dt-bindings: clock: add SM8150 QCOM Graphics clock bindings
  dt-bindings: clock: add SM8250 QCOM Graphics clock bindings
  clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers
  clk: qcom: Add graphics clock controller driver for SM8150
  clk: qcom: Add graphics clock controller driver for SM8250
  dt-bindings: power: Add missing rpmpd rpmh regulator level
  arm64: dts: qcom: add sm8150 GPU nodes
  arm64: dts: qcom: add sm8250 GPU nodes

 ...qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} |  18 +-
 .../bindings/clock/qcom,sc7180-gpucc.yaml     |  74 ----
 arch/arm64/boot/dts/qcom/sm8150.dtsi          | 136 +++++++
 arch/arm64/boot/dts/qcom/sm8250.dtsi          | 143 +++++++
 drivers/clk/qcom/Kconfig                      |  16 +
 drivers/clk/qcom/Makefile                     |   2 +
 drivers/clk/qcom/clk-alpha-pll.c              |  70 ++--
 drivers/clk/qcom/clk-alpha-pll.h              |  15 +-
 drivers/clk/qcom/gcc-sm8150.c                 |  26 +-
 drivers/clk/qcom/gdsc.c                       |  25 ++
 drivers/clk/qcom/gdsc.h                       |   1 +
 drivers/clk/qcom/gpucc-sc7180.c               |  27 +-
 drivers/clk/qcom/gpucc-sdm845.c               |  27 +-
 drivers/clk/qcom/gpucc-sm8150.c               | 320 ++++++++++++++++
 drivers/clk/qcom/gpucc-sm8250.c               | 348 ++++++++++++++++++
 include/dt-bindings/clock/qcom,gpucc-sm8150.h |  33 ++
 include/dt-bindings/clock/qcom,gpucc-sm8250.h |  34 ++
 include/dt-bindings/power/qcom-rpmpd.h        |   1 +
 18 files changed, 1128 insertions(+), 188 deletions(-)
 rename Documentation/devicetree/bindings/clock/{qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} (75%)
 delete mode 100644 Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml
 create mode 100644 drivers/clk/qcom/gpucc-sm8150.c
 create mode 100644 drivers/clk/qcom/gpucc-sm8250.c
 create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8150.h
 create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8250.h

-- 
2.26.1

[PATCH v3 01/14] clk: qcom: gcc: fix sm8150 GPU and NPU clocks

[Jonathan Marek]

Fix the parents and set BRANCH_HALT_SKIP. From the downstream driver it
should be a 500us delay and not skip, however this matches what was done
for other clocks that had 500us delay in downstream.

Fixes: f73a4230d5bb ("clk: qcom: gcc: Add GPU and NPU clocks for SM8150")

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/gcc-sm8150.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/gcc-sm8150.c b/drivers/clk/qcom/gcc-sm8150.c
index 72524cf11048..55e9d6d75a0c 100644
--- a/drivers/clk/qcom/gcc-sm8150.c
+++ b/drivers/clk/qcom/gcc-sm8150.c
@@ -1617,6 +1617,7 @@ static struct clk_branch gcc_gpu_cfg_ahb_clk = {
 };
 
 static struct clk_branch gcc_gpu_gpll0_clk_src = {
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52004,
 		.enable_mask = BIT(15),
@@ -1632,13 +1633,14 @@ static struct clk_branch gcc_gpu_gpll0_clk_src = {
 };
 
 static struct clk_branch gcc_gpu_gpll0_div_clk_src = {
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52004,
 		.enable_mask = BIT(16),
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_gpu_gpll0_div_clk_src",
 			.parent_hws = (const struct clk_hw *[]){
-				&gcc_gpu_gpll0_clk_src.clkr.hw },
+				&gpll0_out_even.clkr.hw },
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
 			.ops = &clk_branch2_ops,
@@ -1729,6 +1731,7 @@ static struct clk_branch gcc_npu_cfg_ahb_clk = {
 };
 
 static struct clk_branch gcc_npu_gpll0_clk_src = {
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52004,
 		.enable_mask = BIT(18),
@@ -1744,13 +1747,14 @@ static struct clk_branch gcc_npu_gpll0_clk_src = {
 };
 
 static struct clk_branch gcc_npu_gpll0_div_clk_src = {
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52004,
 		.enable_mask = BIT(19),
 		.hw.init = &(struct clk_init_data){
 			.name = "gcc_npu_gpll0_div_clk_src",
 			.parent_hws = (const struct clk_hw *[]){
-				&gcc_npu_gpll0_clk_src.clkr.hw },
+				&gpll0_out_even.clkr.hw },
 			.num_parents = 1,
 			.flags = CLK_SET_RATE_PARENT,
 			.ops = &clk_branch2_ops,
-- 
2.26.1

Re: [PATCH v3 01/14] clk: qcom: gcc: fix sm8150 GPU and NPU clocks

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:32)
> Fix the parents and set BRANCH_HALT_SKIP. From the downstream driver it
> should be a 500us delay and not skip, however this matches what was done
> for other clocks that had 500us delay in downstream.
> 
> Fixes: f73a4230d5bb ("clk: qcom: gcc: Add GPU and NPU clocks for SM8150")
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 02/14] clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL

[Jonathan Marek]

0x44 isn't a register offset, it is the value that goes into CAL_L_VAL.

Fixes: 548a909597d5 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/clk-alpha-pll.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 9b2dfa08acb2..1325139173c9 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -56,7 +56,6 @@
 #define PLL_STATUS(p)		((p)->offset + (p)->regs[PLL_OFF_STATUS])
 #define PLL_OPMODE(p)		((p)->offset + (p)->regs[PLL_OFF_OPMODE])
 #define PLL_FRAC(p)		((p)->offset + (p)->regs[PLL_OFF_FRAC])
-#define PLL_CAL_VAL(p)		((p)->offset + (p)->regs[PLL_OFF_CAL_VAL])
 
 const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
 	[CLK_ALPHA_PLL_TYPE_DEFAULT] =  {
@@ -115,7 +114,6 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
 		[PLL_OFF_STATUS] = 0x30,
 		[PLL_OFF_OPMODE] = 0x38,
 		[PLL_OFF_ALPHA_VAL] = 0x40,
-		[PLL_OFF_CAL_VAL] = 0x44,
 	},
 	[CLK_ALPHA_PLL_TYPE_LUCID] =  {
 		[PLL_OFF_L_VAL] = 0x04,
-- 
2.26.1

Re: [PATCH v3 02/14] clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:33)
> 0x44 isn't a register offset, it is the value that goes into CAL_L_VAL.
> 
> Fixes: 548a909597d5 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 03/14] clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid

[Jonathan Marek]

Fixed ops were already identical, this adds support for non-fixed ops by
sharing between trion and lucid.

This also changes the names for trion ops to be consistent with the rest.

Note LUCID_PCAL_DONE is renamed to TRION_PCAL_DONE because it is wrong for
lucid, LUCID_PCAL_DONE should be BIT(27). Next patch will address this.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/clk-alpha-pll.c | 58 ++++++++++----------------------
 drivers/clk/qcom/clk-alpha-pll.h | 17 ++++++----
 drivers/clk/qcom/gcc-sm8150.c    |  8 ++---
 3 files changed, 32 insertions(+), 51 deletions(-)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 1325139173c9..be7ffeae21b1 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -101,21 +101,6 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
 		[PLL_OFF_FRAC] = 0x38,
 	},
 	[CLK_ALPHA_PLL_TYPE_TRION] = {
-		[PLL_OFF_L_VAL] = 0x04,
-		[PLL_OFF_CAL_L_VAL] = 0x08,
-		[PLL_OFF_USER_CTL] = 0x0c,
-		[PLL_OFF_USER_CTL_U] = 0x10,
-		[PLL_OFF_USER_CTL_U1] = 0x14,
-		[PLL_OFF_CONFIG_CTL] = 0x18,
-		[PLL_OFF_CONFIG_CTL_U] = 0x1c,
-		[PLL_OFF_CONFIG_CTL_U1] = 0x20,
-		[PLL_OFF_TEST_CTL] = 0x24,
-		[PLL_OFF_TEST_CTL_U] = 0x28,
-		[PLL_OFF_STATUS] = 0x30,
-		[PLL_OFF_OPMODE] = 0x38,
-		[PLL_OFF_ALPHA_VAL] = 0x40,
-	},
-	[CLK_ALPHA_PLL_TYPE_LUCID] =  {
 		[PLL_OFF_L_VAL] = 0x04,
 		[PLL_OFF_CAL_L_VAL] = 0x08,
 		[PLL_OFF_USER_CTL] = 0x0c,
@@ -154,9 +139,9 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
 #define PLL_OUT_MASK		0x7
 #define PLL_RATE_MARGIN		500
 
-/* LUCID PLL specific settings and offsets */
-#define LUCID_PLL_CAL_VAL	0x44
-#define LUCID_PCAL_DONE		BIT(26)
+/* TRION PLL specific settings and offsets */
+#define TRION_PLL_CAL_VAL	0x44
+#define TRION_PCAL_DONE		BIT(26)
 
 #define pll_alpha_width(p)					\
 		((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ?	\
@@ -910,14 +895,14 @@ const struct clk_ops clk_alpha_pll_hwfsm_ops = {
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_hwfsm_ops);
 
-const struct clk_ops clk_trion_fixed_pll_ops = {
+const struct clk_ops clk_alpha_pll_fixed_trion_ops = {
 	.enable = clk_trion_pll_enable,
 	.disable = clk_trion_pll_disable,
 	.is_enabled = clk_trion_pll_is_enabled,
 	.recalc_rate = clk_trion_pll_recalc_rate,
 	.round_rate = clk_alpha_pll_round_rate,
 };
-EXPORT_SYMBOL_GPL(clk_trion_fixed_pll_ops);
+EXPORT_SYMBOL_GPL(clk_alpha_pll_fixed_trion_ops);
 
 static unsigned long
 clk_alpha_pll_postdiv_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
@@ -1337,12 +1322,12 @@ clk_trion_pll_postdiv_set_rate(struct clk_hw *hw, unsigned long rate,
 				  val << PLL_POST_DIV_SHIFT);
 }
 
-const struct clk_ops clk_trion_pll_postdiv_ops = {
+const struct clk_ops clk_alpha_pll_postdiv_trion_ops = {
 	.recalc_rate = clk_trion_pll_postdiv_recalc_rate,
 	.round_rate = clk_trion_pll_postdiv_round_rate,
 	.set_rate = clk_trion_pll_postdiv_set_rate,
 };
-EXPORT_SYMBOL_GPL(clk_trion_pll_postdiv_ops);
+EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_trion_ops);
 
 static long clk_alpha_pll_postdiv_fabia_round_rate(struct clk_hw *hw,
 				unsigned long rate, unsigned long *prate)
@@ -1397,13 +1382,13 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_fabia_ops);
  * @regmap: register map
  * @config: configuration to apply for pll
  */
-void clk_lucid_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+void clk_trion_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 			     const struct alpha_pll_config *config)
 {
 	if (config->l)
 		regmap_write(regmap, PLL_L_VAL(pll), config->l);
 
-	regmap_write(regmap, PLL_CAL_L_VAL(pll), LUCID_PLL_CAL_VAL);
+	regmap_write(regmap, PLL_CAL_L_VAL(pll), TRION_PLL_CAL_VAL);
 
 	if (config->alpha)
 		regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
@@ -1456,13 +1441,13 @@ void clk_lucid_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 	/* Place the PLL in STANDBY mode */
 	regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
 }
-EXPORT_SYMBOL_GPL(clk_lucid_pll_configure);
+EXPORT_SYMBOL_GPL(clk_trion_pll_configure);
 
 /*
- * The Lucid PLL requires a power-on self-calibration which happens when the
+ * The TRION PLL requires a power-on self-calibration which happens when the
  * PLL comes out of reset. Calibrate in case it is not completed.
  */
-static int alpha_pll_lucid_prepare(struct clk_hw *hw)
+static int alpha_pll_trion_prepare(struct clk_hw *hw)
 {
 	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
 	u32 regval;
@@ -1470,7 +1455,7 @@ static int alpha_pll_lucid_prepare(struct clk_hw *hw)
 
 	/* Return early if calibration is not needed. */
 	regmap_read(pll->clkr.regmap, PLL_STATUS(pll), &regval);
-	if (regval & LUCID_PCAL_DONE)
+	if (regval & TRION_PCAL_DONE)
 		return 0;
 
 	/* On/off to calibrate */
@@ -1481,7 +1466,7 @@ static int alpha_pll_lucid_prepare(struct clk_hw *hw)
 	return ret;
 }
 
-static int alpha_pll_lucid_set_rate(struct clk_hw *hw, unsigned long rate,
+static int alpha_pll_trion_set_rate(struct clk_hw *hw, unsigned long rate,
 				    unsigned long prate)
 {
 	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
@@ -1535,26 +1520,17 @@ static int alpha_pll_lucid_set_rate(struct clk_hw *hw, unsigned long rate,
 	return 0;
 }
 
-const struct clk_ops clk_alpha_pll_lucid_ops = {
-	.prepare = alpha_pll_lucid_prepare,
+const struct clk_ops clk_alpha_pll_trion_ops = {
+	.prepare = alpha_pll_trion_prepare,
 	.enable = clk_trion_pll_enable,
 	.disable = clk_trion_pll_disable,
 	.is_enabled = clk_trion_pll_is_enabled,
 	.recalc_rate = clk_trion_pll_recalc_rate,
 	.round_rate = clk_alpha_pll_round_rate,
-	.set_rate = alpha_pll_lucid_set_rate,
+	.set_rate = alpha_pll_trion_set_rate,
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_lucid_ops);
 
-const struct clk_ops clk_alpha_pll_fixed_lucid_ops = {
-	.enable = clk_trion_pll_enable,
-	.disable = clk_trion_pll_disable,
-	.is_enabled = clk_trion_pll_is_enabled,
-	.recalc_rate = clk_trion_pll_recalc_rate,
-	.round_rate = clk_alpha_pll_round_rate,
-};
-EXPORT_SYMBOL_GPL(clk_alpha_pll_fixed_lucid_ops);
-
 const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
 	.recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
 	.round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 704674a153b6..67f1fd271931 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -14,7 +14,7 @@ enum {
 	CLK_ALPHA_PLL_TYPE_BRAMMO,
 	CLK_ALPHA_PLL_TYPE_FABIA,
 	CLK_ALPHA_PLL_TYPE_TRION,
-	CLK_ALPHA_PLL_TYPE_LUCID,
+	CLK_ALPHA_PLL_TYPE_LUCID = CLK_ALPHA_PLL_TYPE_TRION,
 	CLK_ALPHA_PLL_TYPE_MAX,
 };
 
@@ -128,18 +128,23 @@ extern const struct clk_ops clk_alpha_pll_fabia_ops;
 extern const struct clk_ops clk_alpha_pll_fixed_fabia_ops;
 extern const struct clk_ops clk_alpha_pll_postdiv_fabia_ops;
 
-extern const struct clk_ops clk_alpha_pll_lucid_ops;
-extern const struct clk_ops clk_alpha_pll_fixed_lucid_ops;
+extern const struct clk_ops clk_alpha_pll_trion_ops;
+extern const struct clk_ops clk_alpha_pll_fixed_trion_ops;
+extern const struct clk_ops clk_alpha_pll_postdiv_trion_ops;
+
+#define clk_alpha_pll_lucid_ops clk_alpha_pll_trion_ops
+#define clk_alpha_pll_fixed_lucid_ops clk_alpha_pll_fixed_trion_ops
 extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
 
 void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 			     const struct alpha_pll_config *config);
 void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 				const struct alpha_pll_config *config);
-void clk_lucid_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+void clk_trion_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
 			     const struct alpha_pll_config *config);
+#define clk_lucid_pll_configure(pll, regmap, config) \
+	clk_trion_pll_configure(pll, regmap, config)
+
 
-extern const struct clk_ops clk_trion_fixed_pll_ops;
-extern const struct clk_ops clk_trion_pll_postdiv_ops;
 
 #endif
diff --git a/drivers/clk/qcom/gcc-sm8150.c b/drivers/clk/qcom/gcc-sm8150.c
index 55e9d6d75a0c..d7778def37da 100644
--- a/drivers/clk/qcom/gcc-sm8150.c
+++ b/drivers/clk/qcom/gcc-sm8150.c
@@ -53,7 +53,7 @@ static struct clk_alpha_pll gpll0 = {
 				.name = "bi_tcxo",
 			},
 			.num_parents = 1,
-			.ops = &clk_trion_fixed_pll_ops,
+			.ops = &clk_alpha_pll_fixed_trion_ops,
 		},
 	},
 };
@@ -79,7 +79,7 @@ static struct clk_alpha_pll_postdiv gpll0_out_even = {
 			.hw = &gpll0.clkr.hw,
 		},
 		.num_parents = 1,
-		.ops = &clk_trion_pll_postdiv_ops,
+		.ops = &clk_alpha_pll_postdiv_trion_ops,
 	},
 };
 
@@ -98,7 +98,7 @@ static struct clk_alpha_pll gpll7 = {
 				.name = "bi_tcxo",
 			},
 			.num_parents = 1,
-			.ops = &clk_trion_fixed_pll_ops,
+			.ops = &clk_alpha_pll_fixed_trion_ops,
 		},
 	},
 };
@@ -118,7 +118,7 @@ static struct clk_alpha_pll gpll9 = {
 				.name = "bi_tcxo",
 			},
 			.num_parents = 1,
-			.ops = &clk_trion_fixed_pll_ops,
+			.ops = &clk_alpha_pll_fixed_trion_ops,
 		},
 	},
 };
-- 
2.26.1

Re: [PATCH v3 03/14] clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:34)
> Fixed ops were already identical, this adds support for non-fixed ops by
> sharing between trion and lucid.
> 
> This also changes the names for trion ops to be consistent with the rest.
> 
> Note LUCID_PCAL_DONE is renamed to TRION_PCAL_DONE because it is wrong for
> lucid, LUCID_PCAL_DONE should be BIT(27). Next patch will address this.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 04/14] clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll

[Jonathan Marek]

Lucid PCAL_DONE is different from trion.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/clk-alpha-pll.c | 28 ++++++++++++++++++++++++++--
 drivers/clk/qcom/clk-alpha-pll.h |  2 +-
 2 files changed, 27 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index be7ffeae21b1..26139ef005e4 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -143,6 +143,9 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
 #define TRION_PLL_CAL_VAL	0x44
 #define TRION_PCAL_DONE		BIT(26)
 
+/* LUCID PLL specific settings and offsets */
+#define LUCID_PCAL_DONE		BIT(27)
+
 #define pll_alpha_width(p)					\
 		((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ?	\
 				 ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
@@ -1447,7 +1450,7 @@ EXPORT_SYMBOL_GPL(clk_trion_pll_configure);
  * The TRION PLL requires a power-on self-calibration which happens when the
  * PLL comes out of reset. Calibrate in case it is not completed.
  */
-static int alpha_pll_trion_prepare(struct clk_hw *hw)
+static int __alpha_pll_trion_prepare(struct clk_hw *hw, u32 pcal_done)
 {
 	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
 	u32 regval;
@@ -1455,7 +1458,7 @@ static int alpha_pll_trion_prepare(struct clk_hw *hw)
 
 	/* Return early if calibration is not needed. */
 	regmap_read(pll->clkr.regmap, PLL_STATUS(pll), &regval);
-	if (regval & TRION_PCAL_DONE)
+	if (regval & pcal_done)
 		return 0;
 
 	/* On/off to calibrate */
@@ -1466,6 +1469,16 @@ static int alpha_pll_trion_prepare(struct clk_hw *hw)
 	return ret;
 }
 
+static int alpha_pll_trion_prepare(struct clk_hw *hw)
+{
+	return __alpha_pll_trion_prepare(hw, TRION_PCAL_DONE);
+}
+
+static int alpha_pll_lucid_prepare(struct clk_hw *hw)
+{
+	return __alpha_pll_trion_prepare(hw, LUCID_PCAL_DONE);
+}
+
 static int alpha_pll_trion_set_rate(struct clk_hw *hw, unsigned long rate,
 				    unsigned long prate)
 {
@@ -1529,6 +1542,17 @@ const struct clk_ops clk_alpha_pll_trion_ops = {
 	.round_rate = clk_alpha_pll_round_rate,
 	.set_rate = alpha_pll_trion_set_rate,
 };
+EXPORT_SYMBOL_GPL(clk_alpha_pll_trion_ops);
+
+const struct clk_ops clk_alpha_pll_lucid_ops = {
+	.prepare = alpha_pll_lucid_prepare,
+	.enable = clk_trion_pll_enable,
+	.disable = clk_trion_pll_disable,
+	.is_enabled = clk_trion_pll_is_enabled,
+	.recalc_rate = clk_trion_pll_recalc_rate,
+	.round_rate = clk_alpha_pll_round_rate,
+	.set_rate = alpha_pll_trion_set_rate,
+};
 EXPORT_SYMBOL_GPL(clk_alpha_pll_lucid_ops);
 
 const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 67f1fd271931..69337c1b5850 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -132,7 +132,7 @@ extern const struct clk_ops clk_alpha_pll_trion_ops;
 extern const struct clk_ops clk_alpha_pll_fixed_trion_ops;
 extern const struct clk_ops clk_alpha_pll_postdiv_trion_ops;
 
-#define clk_alpha_pll_lucid_ops clk_alpha_pll_trion_ops
+extern const struct clk_ops clk_alpha_pll_lucid_ops;
 #define clk_alpha_pll_fixed_lucid_ops clk_alpha_pll_fixed_trion_ops
 extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
 
-- 
2.26.1

Re: [PATCH v3 04/14] clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:35)
> Lucid PCAL_DONE is different from trion.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 05/14] clk: qcom: gcc: remove unnecessary vco_table from SM8150

[Jonathan Marek]

The fixed alpha pll ops only use it for clamping in round_rate, which is
unnecessary. This is consistent with SM8250 GCC not using vco_table.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/gcc-sm8150.c | 10 ----------
 1 file changed, 10 deletions(-)

diff --git a/drivers/clk/qcom/gcc-sm8150.c b/drivers/clk/qcom/gcc-sm8150.c
index d7778def37da..8e9b5b3cceaf 100644
--- a/drivers/clk/qcom/gcc-sm8150.c
+++ b/drivers/clk/qcom/gcc-sm8150.c
@@ -34,14 +34,8 @@ enum {
 	P_SLEEP_CLK,
 };
 
-static const struct pll_vco trion_vco[] = {
-	{ 249600000, 2000000000, 0 },
-};
-
 static struct clk_alpha_pll gpll0 = {
 	.offset = 0x0,
-	.vco_table = trion_vco,
-	.num_vco = ARRAY_SIZE(trion_vco),
 	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_TRION],
 	.clkr = {
 		.enable_reg = 0x52000,
@@ -85,8 +79,6 @@ static struct clk_alpha_pll_postdiv gpll0_out_even = {
 
 static struct clk_alpha_pll gpll7 = {
 	.offset = 0x1a000,
-	.vco_table = trion_vco,
-	.num_vco = ARRAY_SIZE(trion_vco),
 	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_TRION],
 	.clkr = {
 		.enable_reg = 0x52000,
@@ -105,8 +97,6 @@ static struct clk_alpha_pll gpll7 = {
 
 static struct clk_alpha_pll gpll9 = {
 	.offset = 0x1c000,
-	.vco_table = trion_vco,
-	.num_vco = ARRAY_SIZE(trion_vco),
 	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_TRION],
 	.clkr = {
 		.enable_reg = 0x52000,
-- 
2.26.1

Re: [PATCH v3 05/14] clk: qcom: gcc: remove unnecessary vco_table from SM8150

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:36)
> The fixed alpha pll ops only use it for clamping in round_rate, which is
> unnecessary. This is consistent with SM8250 GCC not using vco_table.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 06/14] dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc

[Jonathan Marek]

These two bindings are almost identical, so combine them into one. This
will make it easier to add the sm8150 and sm8250 gpucc bindings.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 ...qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} | 14 ++--
 .../bindings/clock/qcom,sc7180-gpucc.yaml     | 74 -------------------
 2 files changed, 9 insertions(+), 79 deletions(-)
 rename Documentation/devicetree/bindings/clock/{qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} (82%)
 delete mode 100644 Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml

diff --git a/Documentation/devicetree/bindings/clock/qcom,sdm845-gpucc.yaml b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
similarity index 82%
rename from Documentation/devicetree/bindings/clock/qcom,sdm845-gpucc.yaml
rename to Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
index 8a0c576ba8b3..aab6bef79771 100644
--- a/Documentation/devicetree/bindings/clock/qcom,sdm845-gpucc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
@@ -1,23 +1,27 @@
 # SPDX-License-Identifier: GPL-2.0-only
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/clock/qcom,sdm845-gpucc.yaml#
+$id: http://devicetree.org/schemas/clock/qcom,gpucc.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: Qualcomm Graphics Clock & Reset Controller Binding for SDM845
+title: Qualcomm Graphics Clock & Reset Controller Binding
 
 maintainers:
   - Taniya Das <tdas@codeaurora.org>
 
 description: |
   Qualcomm graphics clock control module which supports the clocks, resets and
-  power domains on SDM845.
+  power domains on SDM845/SC7180.
 
-  See also dt-bindings/clock/qcom,gpucc-sdm845.h.
+  See also:
+    dt-bindings/clock/qcom,gpucc-sdm845.h
+    dt-bindings/clock/qcom,gpucc-sc7180.h
 
 properties:
   compatible:
-    const: qcom,sdm845-gpucc
+    enum:
+      - qcom,sdm845-gpucc
+      - qcom,sc7180-gpucc
 
   clocks:
     items:
diff --git a/Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml b/Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml
deleted file mode 100644
index fe08461fce05..000000000000
--- a/Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml
+++ /dev/null
@@ -1,74 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/clock/qcom,sc7180-gpucc.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Qualcomm Graphics Clock & Reset Controller Binding for SC7180
-
-maintainers:
-  - Taniya Das <tdas@codeaurora.org>
-
-description: |
-  Qualcomm graphics clock control module which supports the clocks, resets and
-  power domains on SC7180.
-
-  See also dt-bindings/clock/qcom,gpucc-sc7180.h.
-
-properties:
-  compatible:
-    const: qcom,sc7180-gpucc
-
-  clocks:
-    items:
-      - description: Board XO source
-      - description: GPLL0 main branch source
-      - description: GPLL0 div branch source
-
-  clock-names:
-    items:
-      - const: bi_tcxo
-      - const: gcc_gpu_gpll0_clk_src
-      - const: gcc_gpu_gpll0_div_clk_src
-
-  '#clock-cells':
-    const: 1
-
-  '#reset-cells':
-    const: 1
-
-  '#power-domain-cells':
-    const: 1
-
-  reg:
-    maxItems: 1
-
-required:
-  - compatible
-  - reg
-  - clocks
-  - clock-names
-  - '#clock-cells'
-  - '#reset-cells'
-  - '#power-domain-cells'
-
-additionalProperties: false
-
-examples:
-  - |
-    #include <dt-bindings/clock/qcom,gcc-sc7180.h>
-    #include <dt-bindings/clock/qcom,rpmh.h>
-    clock-controller@5090000 {
-      compatible = "qcom,sc7180-gpucc";
-      reg = <0x05090000 0x9000>;
-      clocks = <&rpmhcc RPMH_CXO_CLK>,
-               <&gcc GCC_GPU_GPLL0_CLK_SRC>,
-               <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
-      clock-names = "bi_tcxo",
-                    "gcc_gpu_gpll0_clk_src",
-                    "gcc_gpu_gpll0_div_clk_src";
-      #clock-cells = <1>;
-      #reset-cells = <1>;
-      #power-domain-cells = <1>;
-    };
-...
-- 
2.26.1

Re: [PATCH v3 06/14] dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc

[Rob Herring]

On Thu, 09 Jul 2020 09:52:37 -0400, Jonathan Marek wrote:
> These two bindings are almost identical, so combine them into one. This
> will make it easier to add the sm8150 and sm8250 gpucc bindings.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
>  ...qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} | 14 ++--
>  .../bindings/clock/qcom,sc7180-gpucc.yaml     | 74 -------------------
>  2 files changed, 9 insertions(+), 79 deletions(-)
>  rename Documentation/devicetree/bindings/clock/{qcom,sdm845-gpucc.yaml => qcom,gpucc.yaml} (82%)
>  delete mode 100644 Documentation/devicetree/bindings/clock/qcom,sc7180-gpucc.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 06/14] dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:37)
> These two bindings are almost identical, so combine them into one. This
> will make it easier to add the sm8150 and sm8250 gpucc bindings.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 07/14] dt-bindings: clock: add SM8150 QCOM Graphics clock bindings

[Jonathan Marek]

Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8150 SoCs.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 .../devicetree/bindings/clock/qcom,gpucc.yaml |  4 ++-
 include/dt-bindings/clock/qcom,gpucc-sm8150.h | 33 +++++++++++++++++++
 2 files changed, 36 insertions(+), 1 deletion(-)
 create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8150.h

diff --git a/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
index aab6bef79771..3e064ed0e0ea 100644
--- a/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
@@ -11,17 +11,19 @@ maintainers:
 
 description: |
   Qualcomm graphics clock control module which supports the clocks, resets and
-  power domains on SDM845/SC7180.
+  power domains on SDM845/SC7180/SM8150.
 
   See also:
     dt-bindings/clock/qcom,gpucc-sdm845.h
     dt-bindings/clock/qcom,gpucc-sc7180.h
+    dt-bindings/clock/qcom,gpucc-sm8150.h
 
 properties:
   compatible:
     enum:
       - qcom,sdm845-gpucc
       - qcom,sc7180-gpucc
+      - qcom,sm8150-gpucc
 
   clocks:
     items:
diff --git a/include/dt-bindings/clock/qcom,gpucc-sm8150.h b/include/dt-bindings/clock/qcom,gpucc-sm8150.h
new file mode 100644
index 000000000000..c5b70aad7770
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,gpucc-sm8150.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017-2020, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_GPU_CC_SM8150_H
+#define _DT_BINDINGS_CLK_QCOM_GPU_CC_SM8150_H
+
+/* GPU_CC clock registers */
+#define GPU_CC_AHB_CLK				0
+#define GPU_CC_CRC_AHB_CLK			1
+#define GPU_CC_CX_APB_CLK			2
+#define GPU_CC_CX_GMU_CLK			3
+#define GPU_CC_CX_SNOC_DVM_CLK			4
+#define GPU_CC_CXO_AON_CLK			5
+#define GPU_CC_CXO_CLK				6
+#define GPU_CC_GMU_CLK_SRC			7
+#define GPU_CC_GX_GMU_CLK			8
+#define GPU_CC_PLL1				9
+
+/* GPU_CC Resets */
+#define GPUCC_GPU_CC_CX_BCR			0
+#define GPUCC_GPU_CC_GFX3D_AON_BCR		1
+#define GPUCC_GPU_CC_GMU_BCR			2
+#define GPUCC_GPU_CC_GX_BCR			3
+#define GPUCC_GPU_CC_SPDM_BCR			4
+#define GPUCC_GPU_CC_XO_BCR			5
+
+/* GPU_CC GDSCRs */
+#define GPU_CX_GDSC				0
+#define GPU_GX_GDSC				1
+
+#endif
-- 
2.26.1

Re: [PATCH v3 07/14] dt-bindings: clock: add SM8150 QCOM Graphics clock bindings

[Rob Herring]

On Thu, 09 Jul 2020 09:52:38 -0400, Jonathan Marek wrote:
> Add device tree bindings for graphics clock controller for
> Qualcomm Technology Inc's SM8150 SoCs.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
>  .../devicetree/bindings/clock/qcom,gpucc.yaml |  4 ++-
>  include/dt-bindings/clock/qcom,gpucc-sm8150.h | 33 +++++++++++++++++++
>  2 files changed, 36 insertions(+), 1 deletion(-)
>  create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8150.h
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 07/14] dt-bindings: clock: add SM8150 QCOM Graphics clock bindings

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:38)
> Add device tree bindings for graphics clock controller for
> Qualcomm Technology Inc's SM8150 SoCs.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 08/14] dt-bindings: clock: add SM8250 QCOM Graphics clock bindings

[Jonathan Marek]

Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8250 SoCs.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 .../devicetree/bindings/clock/qcom,gpucc.yaml |  4 ++-
 include/dt-bindings/clock/qcom,gpucc-sm8250.h | 34 +++++++++++++++++++
 2 files changed, 37 insertions(+), 1 deletion(-)
 create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8250.h

diff --git a/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
index 3e064ed0e0ea..df943c4c3234 100644
--- a/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,gpucc.yaml
@@ -11,12 +11,13 @@ maintainers:
 
 description: |
   Qualcomm graphics clock control module which supports the clocks, resets and
-  power domains on SDM845/SC7180/SM8150.
+  power domains on SDM845/SC7180/SM8150/SM8250.
 
   See also:
     dt-bindings/clock/qcom,gpucc-sdm845.h
     dt-bindings/clock/qcom,gpucc-sc7180.h
     dt-bindings/clock/qcom,gpucc-sm8150.h
+    dt-bindings/clock/qcom,gpucc-sm8250.h
 
 properties:
   compatible:
@@ -24,6 +25,7 @@ properties:
       - qcom,sdm845-gpucc
       - qcom,sc7180-gpucc
       - qcom,sm8150-gpucc
+      - qcom,sm8250-gpucc
 
   clocks:
     items:
diff --git a/include/dt-bindings/clock/qcom,gpucc-sm8250.h b/include/dt-bindings/clock/qcom,gpucc-sm8250.h
new file mode 100644
index 000000000000..dc8e387c48ad
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,gpucc-sm8250.h
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017-2020, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_GPU_CC_SM8250_H
+#define _DT_BINDINGS_CLK_QCOM_GPU_CC_SM8250_H
+
+/* GPU_CC clock registers */
+#define GPU_CC_AHB_CLK				0
+#define GPU_CC_CRC_AHB_CLK			1
+#define GPU_CC_CX_APB_CLK			2
+#define GPU_CC_CX_GMU_CLK			3
+#define GPU_CC_CX_SNOC_DVM_CLK			4
+#define GPU_CC_CXO_AON_CLK			5
+#define GPU_CC_CXO_CLK				6
+#define GPU_CC_GMU_CLK_SRC			7
+#define GPU_CC_GX_GMU_CLK			8
+#define GPU_CC_PLL1				9
+#define GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK		10
+
+/* GPU_CC Resets */
+#define GPUCC_GPU_CC_ACD_BCR			0
+#define GPUCC_GPU_CC_CX_BCR			1
+#define GPUCC_GPU_CC_GFX3D_AON_BCR		2
+#define GPUCC_GPU_CC_GMU_BCR			3
+#define GPUCC_GPU_CC_GX_BCR			4
+#define GPUCC_GPU_CC_XO_BCR			5
+
+/* GPU_CC GDSCRs */
+#define GPU_CX_GDSC				0
+#define GPU_GX_GDSC				1
+
+#endif
-- 
2.26.1

Re: [PATCH v3 08/14] dt-bindings: clock: add SM8250 QCOM Graphics clock bindings

[Rob Herring]

On Thu, 09 Jul 2020 09:52:39 -0400, Jonathan Marek wrote:
> Add device tree bindings for graphics clock controller for
> Qualcomm Technology Inc's SM8250 SoCs.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
>  .../devicetree/bindings/clock/qcom,gpucc.yaml |  4 ++-
>  include/dt-bindings/clock/qcom,gpucc-sm8250.h | 34 +++++++++++++++++++
>  2 files changed, 37 insertions(+), 1 deletion(-)
>  create mode 100644 include/dt-bindings/clock/qcom,gpucc-sm8250.h
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 08/14] dt-bindings: clock: add SM8250 QCOM Graphics clock bindings

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:39)
> Add device tree bindings for graphics clock controller for
> Qualcomm Technology Inc's SM8250 SoCs.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 09/14] clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers

[Jonathan Marek]

All gpucc drivers need this, so move it to common code instead of
duplicating it in every gpucc driver.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/gdsc.c         | 25 +++++++++++++++++++++++++
 drivers/clk/qcom/gdsc.h         |  1 +
 drivers/clk/qcom/gpucc-sc7180.c | 27 +--------------------------
 drivers/clk/qcom/gpucc-sdm845.c | 27 +--------------------------
 4 files changed, 28 insertions(+), 52 deletions(-)

diff --git a/drivers/clk/qcom/gdsc.c b/drivers/clk/qcom/gdsc.c
index 04944f11659b..628397703717 100644
--- a/drivers/clk/qcom/gdsc.c
+++ b/drivers/clk/qcom/gdsc.c
@@ -433,3 +433,28 @@ void gdsc_unregister(struct gdsc_desc *desc)
 	}
 	of_genpd_del_provider(dev->of_node);
 }
+
+/*
+ * On SDM845+ the GPU GX domain is *almost* entirely controlled by the GMU
+ * running in the CX domain so the CPU doesn't need to know anything about the
+ * GX domain EXCEPT....
+ *
+ * Hardware constraints dictate that the GX be powered down before the CX. If
+ * the GMU crashes it could leave the GX on. In order to successfully bring back
+ * the device the CPU needs to disable the GX headswitch. There being no sane
+ * way to reach in and touch that register from deep inside the GPU driver we
+ * need to set up the infrastructure to be able to ensure that the GPU can
+ * ensure that the GX is off during this super special case. We do this by
+ * defining a GX gdsc with a dummy enable function and a "default" disable
+ * function.
+ *
+ * This allows us to attach with genpd_dev_pm_attach_by_name() in the GPU
+ * driver. During power up, nothing will happen from the CPU (and the GMU will
+ * power up normally but during power down this will ensure that the GX domain
+ * is *really* off - this gives us a semi standard way of doing what we need.
+ */
+int gdsc_gx_do_nothing_enable(struct generic_pm_domain *domain)
+{
+	/* Do nothing but give genpd the impression that we were successful */
+	return 0;
+}
diff --git a/drivers/clk/qcom/gdsc.h b/drivers/clk/qcom/gdsc.h
index c36fc26dcdff..1896bfb2bbd1 100644
--- a/drivers/clk/qcom/gdsc.h
+++ b/drivers/clk/qcom/gdsc.h
@@ -68,6 +68,7 @@ struct gdsc_desc {
 int gdsc_register(struct gdsc_desc *desc, struct reset_controller_dev *,
 		  struct regmap *);
 void gdsc_unregister(struct gdsc_desc *desc);
+int gdsc_gx_do_nothing_enable(struct generic_pm_domain *domain);
 #else
 static inline int gdsc_register(struct gdsc_desc *desc,
 				struct reset_controller_dev *rcdev,
diff --git a/drivers/clk/qcom/gpucc-sc7180.c b/drivers/clk/qcom/gpucc-sc7180.c
index 7b656b6aeced..88a739b6fec3 100644
--- a/drivers/clk/qcom/gpucc-sc7180.c
+++ b/drivers/clk/qcom/gpucc-sc7180.c
@@ -170,37 +170,12 @@ static struct gdsc cx_gdsc = {
 	.flags = VOTABLE,
 };
 
-/*
- * On SC7180 the GPU GX domain is *almost* entirely controlled by the GMU
- * running in the CX domain so the CPU doesn't need to know anything about the
- * GX domain EXCEPT....
- *
- * Hardware constraints dictate that the GX be powered down before the CX. If
- * the GMU crashes it could leave the GX on. In order to successfully bring back
- * the device the CPU needs to disable the GX headswitch. There being no sane
- * way to reach in and touch that register from deep inside the GPU driver we
- * need to set up the infrastructure to be able to ensure that the GPU can
- * ensure that the GX is off during this super special case. We do this by
- * defining a GX gdsc with a dummy enable function and a "default" disable
- * function.
- *
- * This allows us to attach with genpd_dev_pm_attach_by_name() in the GPU
- * driver. During power up, nothing will happen from the CPU (and the GMU will
- * power up normally but during power down this will ensure that the GX domain
- * is *really* off - this gives us a semi standard way of doing what we need.
- */
-static int gx_gdsc_enable(struct generic_pm_domain *domain)
-{
-	/* Do nothing but give genpd the impression that we were successful */
-	return 0;
-}
-
 static struct gdsc gx_gdsc = {
 	.gdscr = 0x100c,
 	.clamp_io_ctrl = 0x1508,
 	.pd = {
 		.name = "gx_gdsc",
-		.power_on = gx_gdsc_enable,
+		.power_on = gdsc_gx_do_nothing_enable,
 	},
 	.pwrsts = PWRSTS_OFF_ON,
 	.flags = CLAMP_IO,
diff --git a/drivers/clk/qcom/gpucc-sdm845.c b/drivers/clk/qcom/gpucc-sdm845.c
index e40efba1bf7d..5663698b306b 100644
--- a/drivers/clk/qcom/gpucc-sdm845.c
+++ b/drivers/clk/qcom/gpucc-sdm845.c
@@ -131,37 +131,12 @@ static struct gdsc gpu_cx_gdsc = {
 	.flags = VOTABLE,
 };
 
-/*
- * On SDM845 the GPU GX domain is *almost* entirely controlled by the GMU
- * running in the CX domain so the CPU doesn't need to know anything about the
- * GX domain EXCEPT....
- *
- * Hardware constraints dictate that the GX be powered down before the CX. If
- * the GMU crashes it could leave the GX on. In order to successfully bring back
- * the device the CPU needs to disable the GX headswitch. There being no sane
- * way to reach in and touch that register from deep inside the GPU driver we
- * need to set up the infrastructure to be able to ensure that the GPU can
- * ensure that the GX is off during this super special case. We do this by
- * defining a GX gdsc with a dummy enable function and a "default" disable
- * function.
- *
- * This allows us to attach with genpd_dev_pm_attach_by_name() in the GPU
- * driver. During power up, nothing will happen from the CPU (and the GMU will
- * power up normally but during power down this will ensure that the GX domain
- * is *really* off - this gives us a semi standard way of doing what we need.
- */
-static int gx_gdsc_enable(struct generic_pm_domain *domain)
-{
-	/* Do nothing but give genpd the impression that we were successful */
-	return 0;
-}
-
 static struct gdsc gpu_gx_gdsc = {
 	.gdscr = 0x100c,
 	.clamp_io_ctrl = 0x1508,
 	.pd = {
 		.name = "gpu_gx_gdsc",
-		.power_on = gx_gdsc_enable,
+		.power_on = gdsc_gx_do_nothing_enable,
 	},
 	.pwrsts = PWRSTS_OFF_ON,
 	.flags = CLAMP_IO | AON_RESET | POLL_CFG_GDSCR,
-- 
2.26.1

Re: [PATCH v3 09/14] clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:40)
> All gpucc drivers need this, so move it to common code instead of
> duplicating it in every gpucc driver.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 10/14] clk: qcom: Add graphics clock controller driver for SM8150

[Jonathan Marek]

Add support for the graphics clock controller found on SM8150
based devices.

This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/Kconfig        |   8 +
 drivers/clk/qcom/Makefile       |   1 +
 drivers/clk/qcom/gpucc-sm8150.c | 320 ++++++++++++++++++++++++++++++++
 3 files changed, 329 insertions(+)
 create mode 100644 drivers/clk/qcom/gpucc-sm8150.c

diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index cde6ca90a06b..1bf5e927ee0d 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -391,6 +391,14 @@ config SM_GCC_8250
 	  Say Y if you want to use peripheral devices such as UART,
 	  SPI, I2C, USB, SD/UFS, PCIe etc.
 
+config SM_GPUCC_8150
+	tristate "SM8150 Graphics Clock Controller"
+	select SM_GCC_8150
+	help
+	  Support for the graphics clock controller on SM8150 devices.
+	  Say Y if you want to support graphics controller devices and
+	  functionality such as 3D graphics.
+
 config SPMI_PMIC_CLKDIV
 	tristate "SPMI PMIC clkdiv Support"
 	depends on SPMI || COMPILE_TEST
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 7ec8561a1270..f819663c53a6 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_SDM_LPASSCC_845) += lpasscc-sdm845.o
 obj-$(CONFIG_SDM_VIDEOCC_845) += videocc-sdm845.o
 obj-$(CONFIG_SM_GCC_8150) += gcc-sm8150.o
 obj-$(CONFIG_SM_GCC_8250) += gcc-sm8250.o
+obj-$(CONFIG_SM_GPUCC_8150) += gpucc-sm8150.o
 obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
 obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
 obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
diff --git a/drivers/clk/qcom/gpucc-sm8150.c b/drivers/clk/qcom/gpucc-sm8150.c
new file mode 100644
index 000000000000..27c40754b2c7
--- /dev/null
+++ b/drivers/clk/qcom/gpucc-sm8150.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017-2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,gpucc-sm8150.h>
+
+#include "common.h"
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "reset.h"
+#include "gdsc.h"
+
+enum {
+	P_BI_TCXO,
+	P_CORE_BI_PLL_TEST_SE,
+	P_GPLL0_OUT_MAIN,
+	P_GPLL0_OUT_MAIN_DIV,
+	P_GPU_CC_PLL1_OUT_MAIN,
+};
+
+static const struct pll_vco trion_vco[] = {
+	{ 249600000, 2000000000, 0 },
+};
+
+static struct alpha_pll_config gpu_cc_pll1_config = {
+	.l = 0x1a,
+	.alpha = 0xaaa,
+	.config_ctl_val = 0x20485699,
+	.config_ctl_hi_val = 0x00002267,
+	.config_ctl_hi1_val = 0x00000024,
+	.test_ctl_val = 0x00000000,
+	.test_ctl_hi_val = 0x00000002,
+	.test_ctl_hi1_val = 0x00000000,
+	.user_ctl_val = 0x00000000,
+	.user_ctl_hi_val = 0x00000805,
+	.user_ctl_hi1_val = 0x000000d0,
+};
+
+static struct clk_alpha_pll gpu_cc_pll1 = {
+	.offset = 0x100,
+	.vco_table = trion_vco,
+	.num_vco = ARRAY_SIZE(trion_vco),
+	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_TRION],
+	.clkr = {
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_pll1",
+			.parent_data =  &(const struct clk_parent_data){
+				.fw_name = "bi_tcxo",
+			},
+			.num_parents = 1,
+			.ops = &clk_alpha_pll_trion_ops,
+		},
+	},
+};
+
+static const struct parent_map gpu_cc_parent_map_0[] = {
+	{ P_BI_TCXO, 0 },
+	{ P_GPU_CC_PLL1_OUT_MAIN, 3 },
+	{ P_GPLL0_OUT_MAIN, 5 },
+	{ P_GPLL0_OUT_MAIN_DIV, 6 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_0[] = {
+	{ .fw_name = "bi_tcxo" },
+	{ .hw = &gpu_cc_pll1.clkr.hw },
+	{ .fw_name = "gcc_gpu_gpll0_clk_src" },
+	{ .fw_name = "gcc_gpu_gpll0_div_clk_src" },
+};
+
+static const struct freq_tbl ftbl_gpu_cc_gmu_clk_src[] = {
+	F(19200000, P_BI_TCXO, 1, 0, 0),
+	F(200000000, P_GPLL0_OUT_MAIN_DIV, 1.5, 0, 0),
+	F(500000000, P_GPU_CC_PLL1_OUT_MAIN, 1, 0, 0),
+	{ }
+};
+
+static struct clk_rcg2 gpu_cc_gmu_clk_src = {
+	.cmd_rcgr = 0x1120,
+	.mnd_width = 0,
+	.hid_width = 5,
+	.parent_map = gpu_cc_parent_map_0,
+	.freq_tbl = ftbl_gpu_cc_gmu_clk_src,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "gpu_cc_gmu_clk_src",
+		.parent_data = gpu_cc_parent_data_0,
+		.num_parents = ARRAY_SIZE(gpu_cc_parent_data_0),
+		.flags = CLK_SET_RATE_PARENT,
+		.ops = &clk_rcg2_ops,
+	},
+};
+
+static struct clk_branch gpu_cc_ahb_clk = {
+	.halt_reg = 0x1078,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x1078,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_ahb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_crc_ahb_clk = {
+	.halt_reg = 0x107c,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x107c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_crc_ahb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_apb_clk = {
+	.halt_reg = 0x1088,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1088,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_apb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_gmu_clk = {
+	.halt_reg = 0x1098,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1098,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_gmu_clk",
+			.parent_data =  &(const struct clk_parent_data){
+				.hw = &gpu_cc_gmu_clk_src.clkr.hw,
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_snoc_dvm_clk = {
+	.halt_reg = 0x108c,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x108c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_snoc_dvm_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cxo_aon_clk = {
+	.halt_reg = 0x1004,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1004,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cxo_aon_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cxo_clk = {
+	.halt_reg = 0x109c,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x109c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cxo_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_gx_gmu_clk = {
+	.halt_reg = 0x1064,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1064,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_gx_gmu_clk",
+			.parent_data =  &(const struct clk_parent_data){
+				.hw = &gpu_cc_gmu_clk_src.clkr.hw,
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct gdsc gpu_cx_gdsc = {
+	.gdscr = 0x106c,
+	.gds_hw_ctrl = 0x1540,
+	.pd = {
+		.name = "gpu_cx_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
+};
+
+static struct gdsc gpu_gx_gdsc = {
+	.gdscr = 0x100c,
+	.clamp_io_ctrl = 0x1508,
+	.pd = {
+		.name = "gpu_gx_gdsc",
+		.power_on = gdsc_gx_do_nothing_enable,
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+	.flags = CLAMP_IO | AON_RESET | POLL_CFG_GDSCR,
+};
+
+static struct clk_regmap *gpu_cc_sm8150_clocks[] = {
+	[GPU_CC_AHB_CLK] = &gpu_cc_ahb_clk.clkr,
+	[GPU_CC_CRC_AHB_CLK] = &gpu_cc_crc_ahb_clk.clkr,
+	[GPU_CC_CX_APB_CLK] = &gpu_cc_cx_apb_clk.clkr,
+	[GPU_CC_CX_GMU_CLK] = &gpu_cc_cx_gmu_clk.clkr,
+	[GPU_CC_CX_SNOC_DVM_CLK] = &gpu_cc_cx_snoc_dvm_clk.clkr,
+	[GPU_CC_CXO_AON_CLK] = &gpu_cc_cxo_aon_clk.clkr,
+	[GPU_CC_CXO_CLK] = &gpu_cc_cxo_clk.clkr,
+	[GPU_CC_GMU_CLK_SRC] = &gpu_cc_gmu_clk_src.clkr,
+	[GPU_CC_GX_GMU_CLK] = &gpu_cc_gx_gmu_clk.clkr,
+	[GPU_CC_PLL1] = &gpu_cc_pll1.clkr,
+};
+
+static const struct qcom_reset_map gpu_cc_sm8150_resets[] = {
+	[GPUCC_GPU_CC_CX_BCR] = { 0x1068 },
+	[GPUCC_GPU_CC_GMU_BCR] = { 0x111c },
+	[GPUCC_GPU_CC_GX_BCR] = { 0x1008 },
+	[GPUCC_GPU_CC_SPDM_BCR] = { 0x1110 },
+	[GPUCC_GPU_CC_XO_BCR] = { 0x1000 },
+};
+
+static struct gdsc *gpu_cc_sm8150_gdscs[] = {
+	[GPU_CX_GDSC] = &gpu_cx_gdsc,
+	[GPU_GX_GDSC] = &gpu_gx_gdsc,
+};
+
+static const struct regmap_config gpu_cc_sm8150_regmap_config = {
+	.reg_bits	= 32,
+	.reg_stride	= 4,
+	.val_bits	= 32,
+	.max_register	= 0x8008,
+	.fast_io	= true,
+};
+
+static const struct qcom_cc_desc gpu_cc_sm8150_desc = {
+	.config = &gpu_cc_sm8150_regmap_config,
+	.clks = gpu_cc_sm8150_clocks,
+	.num_clks = ARRAY_SIZE(gpu_cc_sm8150_clocks),
+	.resets = gpu_cc_sm8150_resets,
+	.num_resets = ARRAY_SIZE(gpu_cc_sm8150_resets),
+	.gdscs = gpu_cc_sm8150_gdscs,
+	.num_gdscs = ARRAY_SIZE(gpu_cc_sm8150_gdscs),
+};
+
+static const struct of_device_id gpu_cc_sm8150_match_table[] = {
+	{ .compatible = "qcom,sm8150-gpucc" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, gpu_cc_sm8150_match_table);
+
+static int gpu_cc_sm8150_probe(struct platform_device *pdev)
+{
+	struct regmap *regmap;
+
+	regmap = qcom_cc_map(pdev, &gpu_cc_sm8150_desc);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	clk_trion_pll_configure(&gpu_cc_pll1, regmap, &gpu_cc_pll1_config);
+
+	return qcom_cc_really_probe(pdev, &gpu_cc_sm8150_desc, regmap);
+}
+
+static struct platform_driver gpu_cc_sm8150_driver = {
+	.probe = gpu_cc_sm8150_probe,
+	.driver = {
+		.name = "sm8150-gpucc",
+		.of_match_table = gpu_cc_sm8150_match_table,
+	},
+};
+
+static int __init gpu_cc_sm8150_init(void)
+{
+	return platform_driver_register(&gpu_cc_sm8150_driver);
+}
+subsys_initcall(gpu_cc_sm8150_init);
+
+static void __exit gpu_cc_sm8150_exit(void)
+{
+	platform_driver_unregister(&gpu_cc_sm8150_driver);
+}
+module_exit(gpu_cc_sm8150_exit);
+
+MODULE_DESCRIPTION("QTI GPUCC SM8150 Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.26.1

Re: [PATCH v3 10/14] clk: qcom: Add graphics clock controller driver for SM8150

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:41)
> Add support for the graphics clock controller found on SM8150
> based devices.
> 
> This is initially copied from the downstream kernel, but has
> been modified to more closely match the upstream sc7180 driver.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 11/14] clk: qcom: Add graphics clock controller driver for SM8250

[Jonathan Marek]

Add support for the graphics clock controller found on SM8250
based devices.

This is initially copied from the downstream kernel, but has
been modified to more closely match the upstream sc7180 driver.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 drivers/clk/qcom/Kconfig        |   8 +
 drivers/clk/qcom/Makefile       |   1 +
 drivers/clk/qcom/gpucc-sm8250.c | 348 ++++++++++++++++++++++++++++++++
 3 files changed, 357 insertions(+)
 create mode 100644 drivers/clk/qcom/gpucc-sm8250.c

diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 1bf5e927ee0d..125215e71ec7 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -399,6 +399,14 @@ config SM_GPUCC_8150
 	  Say Y if you want to support graphics controller devices and
 	  functionality such as 3D graphics.
 
+config SM_GPUCC_8250
+	tristate "SM8250 Graphics Clock Controller"
+	select SM_GCC_8250
+	help
+	  Support for the graphics clock controller on SM8250 devices.
+	  Say Y if you want to support graphics controller devices and
+	  functionality such as 3D graphics.
+
 config SPMI_PMIC_CLKDIV
 	tristate "SPMI PMIC clkdiv Support"
 	depends on SPMI || COMPILE_TEST
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index f819663c53a6..b5dcb61af7f2 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_SDM_VIDEOCC_845) += videocc-sdm845.o
 obj-$(CONFIG_SM_GCC_8150) += gcc-sm8150.o
 obj-$(CONFIG_SM_GCC_8250) += gcc-sm8250.o
 obj-$(CONFIG_SM_GPUCC_8150) += gpucc-sm8150.o
+obj-$(CONFIG_SM_GPUCC_8250) += gpucc-sm8250.o
 obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
 obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
 obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
diff --git a/drivers/clk/qcom/gpucc-sm8250.c b/drivers/clk/qcom/gpucc-sm8250.c
new file mode 100644
index 000000000000..49b0b071778d
--- /dev/null
+++ b/drivers/clk/qcom/gpucc-sm8250.c
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,gpucc-sm8250.h>
+
+#include "common.h"
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "reset.h"
+#include "gdsc.h"
+
+#define CX_GMU_CBCR_SLEEP_MASK		0xf
+#define CX_GMU_CBCR_SLEEP_SHIFT		4
+#define CX_GMU_CBCR_WAKE_MASK		0xf
+#define CX_GMU_CBCR_WAKE_SHIFT		8
+
+enum {
+	P_BI_TCXO,
+	P_CORE_BI_PLL_TEST_SE,
+	P_GPLL0_OUT_MAIN,
+	P_GPLL0_OUT_MAIN_DIV,
+	P_GPU_CC_PLL0_OUT_MAIN,
+	P_GPU_CC_PLL1_OUT_MAIN,
+};
+
+static struct pll_vco lucid_vco[] = {
+	{ 249600000, 2000000000, 0 },
+};
+
+static const struct alpha_pll_config gpu_cc_pll1_config = {
+	.l = 0x1a,
+	.alpha = 0xaaa,
+	.config_ctl_val = 0x20485699,
+	.config_ctl_hi_val = 0x00002261,
+	.config_ctl_hi1_val = 0x029a699c,
+	.user_ctl_val = 0x00000000,
+	.user_ctl_hi_val = 0x00000805,
+	.user_ctl_hi1_val = 0x00000000,
+};
+
+static struct clk_alpha_pll gpu_cc_pll1 = {
+	.offset = 0x100,
+	.vco_table = lucid_vco,
+	.num_vco = ARRAY_SIZE(lucid_vco),
+	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID],
+	.clkr = {
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_pll1",
+			.parent_data =  &(const struct clk_parent_data){
+				.fw_name = "bi_tcxo",
+			},
+			.num_parents = 1,
+			.ops = &clk_alpha_pll_lucid_ops,
+		},
+	},
+};
+
+static const struct parent_map gpu_cc_parent_map_0[] = {
+	{ P_BI_TCXO, 0 },
+	{ P_GPU_CC_PLL1_OUT_MAIN, 3 },
+	{ P_GPLL0_OUT_MAIN, 5 },
+	{ P_GPLL0_OUT_MAIN_DIV, 6 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_0[] = {
+	{ .fw_name = "bi_tcxo" },
+	{ .hw = &gpu_cc_pll1.clkr.hw },
+	{ .fw_name = "gcc_gpu_gpll0_clk_src" },
+	{ .fw_name = "gcc_gpu_gpll0_div_clk_src" },
+};
+
+static const struct freq_tbl ftbl_gpu_cc_gmu_clk_src[] = {
+	F(19200000, P_BI_TCXO, 1, 0, 0),
+	F(200000000, P_GPLL0_OUT_MAIN_DIV, 1.5, 0, 0),
+	F(500000000, P_GPU_CC_PLL1_OUT_MAIN, 1, 0, 0),
+	{ }
+};
+
+static struct clk_rcg2 gpu_cc_gmu_clk_src = {
+	.cmd_rcgr = 0x1120,
+	.mnd_width = 0,
+	.hid_width = 5,
+	.parent_map = gpu_cc_parent_map_0,
+	.freq_tbl = ftbl_gpu_cc_gmu_clk_src,
+	.clkr.hw.init = &(struct clk_init_data){
+		.name = "gpu_cc_gmu_clk_src",
+		.parent_data = gpu_cc_parent_data_0,
+		.num_parents = ARRAY_SIZE(gpu_cc_parent_data_0),
+		.flags = CLK_SET_RATE_PARENT,
+		.ops = &clk_rcg2_ops,
+	},
+};
+
+static struct clk_branch gpu_cc_ahb_clk = {
+	.halt_reg = 0x1078,
+	.halt_check = BRANCH_HALT_DELAY,
+	.clkr = {
+		.enable_reg = 0x1078,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_ahb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_crc_ahb_clk = {
+	.halt_reg = 0x107c,
+	.halt_check = BRANCH_HALT_VOTED,
+	.clkr = {
+		.enable_reg = 0x107c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_crc_ahb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_apb_clk = {
+	.halt_reg = 0x1088,
+	.halt_check = BRANCH_HALT_VOTED,
+	.clkr = {
+		.enable_reg = 0x1088,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_apb_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_gmu_clk = {
+	.halt_reg = 0x1098,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1098,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_gmu_clk",
+			.parent_data =  &(const struct clk_parent_data){
+				.hw = &gpu_cc_gmu_clk_src.clkr.hw,
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cx_snoc_dvm_clk = {
+	.halt_reg = 0x108c,
+	.halt_check = BRANCH_HALT_VOTED,
+	.clkr = {
+		.enable_reg = 0x108c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cx_snoc_dvm_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cxo_aon_clk = {
+	.halt_reg = 0x1004,
+	.halt_check = BRANCH_HALT_VOTED,
+	.clkr = {
+		.enable_reg = 0x1004,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cxo_aon_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_cxo_clk = {
+	.halt_reg = 0x109c,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x109c,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_cxo_clk",
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_gx_gmu_clk = {
+	.halt_reg = 0x1064,
+	.halt_check = BRANCH_HALT,
+	.clkr = {
+		.enable_reg = 0x1064,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			.name = "gpu_cc_gx_gmu_clk",
+			.parent_data =  &(const struct clk_parent_data){
+				.hw = &gpu_cc_gmu_clk_src.clkr.hw,
+			},
+			.num_parents = 1,
+			.flags = CLK_SET_RATE_PARENT,
+			.ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct clk_branch gpu_cc_hlos1_vote_gpu_smmu_clk = {
+	.halt_reg = 0x5000,
+	.halt_check = BRANCH_VOTED,
+	.clkr = {
+		.enable_reg = 0x5000,
+		.enable_mask = BIT(0),
+		.hw.init = &(struct clk_init_data){
+			 .name = "gpu_cc_hlos1_vote_gpu_smmu_clk",
+			 .ops = &clk_branch2_ops,
+		},
+	},
+};
+
+static struct gdsc gpu_cx_gdsc = {
+	.gdscr = 0x106c,
+	.gds_hw_ctrl = 0x1540,
+	.pd = {
+		.name = "gpu_cx_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+	.flags = VOTABLE,
+};
+
+static struct gdsc gpu_gx_gdsc = {
+	.gdscr = 0x100c,
+	.clamp_io_ctrl = 0x1508,
+	.pd = {
+		.name = "gpu_gx_gdsc",
+		.power_on = gdsc_gx_do_nothing_enable,
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+	.flags = CLAMP_IO | AON_RESET | POLL_CFG_GDSCR,
+};
+
+static struct clk_regmap *gpu_cc_sm8250_clocks[] = {
+	[GPU_CC_AHB_CLK] = &gpu_cc_ahb_clk.clkr,
+	[GPU_CC_CRC_AHB_CLK] = &gpu_cc_crc_ahb_clk.clkr,
+	[GPU_CC_CX_APB_CLK] = &gpu_cc_cx_apb_clk.clkr,
+	[GPU_CC_CX_GMU_CLK] = &gpu_cc_cx_gmu_clk.clkr,
+	[GPU_CC_CX_SNOC_DVM_CLK] = &gpu_cc_cx_snoc_dvm_clk.clkr,
+	[GPU_CC_CXO_AON_CLK] = &gpu_cc_cxo_aon_clk.clkr,
+	[GPU_CC_CXO_CLK] = &gpu_cc_cxo_clk.clkr,
+	[GPU_CC_GMU_CLK_SRC] = &gpu_cc_gmu_clk_src.clkr,
+	[GPU_CC_GX_GMU_CLK] = &gpu_cc_gx_gmu_clk.clkr,
+	[GPU_CC_PLL1] = &gpu_cc_pll1.clkr,
+	[GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK] = &gpu_cc_hlos1_vote_gpu_smmu_clk.clkr,
+};
+
+static const struct qcom_reset_map gpu_cc_sm8250_resets[] = {
+	[GPUCC_GPU_CC_ACD_BCR] = { 0x1160 },
+	[GPUCC_GPU_CC_CX_BCR] = { 0x1068 },
+	[GPUCC_GPU_CC_GFX3D_AON_BCR] = { 0x10a0 },
+	[GPUCC_GPU_CC_GMU_BCR] = { 0x111c },
+	[GPUCC_GPU_CC_GX_BCR] = { 0x1008 },
+	[GPUCC_GPU_CC_XO_BCR] = { 0x1000 },
+};
+
+static struct gdsc *gpu_cc_sm8250_gdscs[] = {
+	[GPU_CX_GDSC] = &gpu_cx_gdsc,
+	[GPU_GX_GDSC] = &gpu_gx_gdsc,
+};
+
+static const struct regmap_config gpu_cc_sm8250_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.max_register = 0x8008,
+	.fast_io = true,
+};
+
+static const struct qcom_cc_desc gpu_cc_sm8250_desc = {
+	.config = &gpu_cc_sm8250_regmap_config,
+	.clks = gpu_cc_sm8250_clocks,
+	.num_clks = ARRAY_SIZE(gpu_cc_sm8250_clocks),
+	.resets = gpu_cc_sm8250_resets,
+	.num_resets = ARRAY_SIZE(gpu_cc_sm8250_resets),
+	.gdscs = gpu_cc_sm8250_gdscs,
+	.num_gdscs = ARRAY_SIZE(gpu_cc_sm8250_gdscs),
+};
+
+static const struct of_device_id gpu_cc_sm8250_match_table[] = {
+	{ .compatible = "qcom,sm8250-gpucc" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, gpu_cc_sm8250_match_table);
+
+static int gpu_cc_sm8250_probe(struct platform_device *pdev)
+{
+	struct regmap *regmap;
+	unsigned int value, mask;
+
+	regmap = qcom_cc_map(pdev, &gpu_cc_sm8250_desc);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	clk_lucid_pll_configure(&gpu_cc_pll1, regmap, &gpu_cc_pll1_config);
+
+	/*
+	 * Configure gpu_cc_cx_gmu_clk with recommended
+	 * wakeup/sleep settings
+	 */
+	mask = CX_GMU_CBCR_WAKE_MASK << CX_GMU_CBCR_WAKE_SHIFT;
+	mask |= CX_GMU_CBCR_SLEEP_MASK << CX_GMU_CBCR_SLEEP_SHIFT;
+	value = 0xf << CX_GMU_CBCR_WAKE_SHIFT | 0xf << CX_GMU_CBCR_SLEEP_SHIFT;
+	regmap_update_bits(regmap, 0x1098, mask, value);
+
+	return qcom_cc_really_probe(pdev, &gpu_cc_sm8250_desc, regmap);;
+}
+
+static struct platform_driver gpu_cc_sm8250_driver = {
+	.probe = gpu_cc_sm8250_probe,
+	.driver = {
+		.name = "sm8250-gpucc",
+		.of_match_table = gpu_cc_sm8250_match_table,
+	},
+};
+
+static int __init gpu_cc_sm8250_init(void)
+{
+	return platform_driver_register(&gpu_cc_sm8250_driver);
+}
+subsys_initcall(gpu_cc_sm8250_init);
+
+static void __exit gpu_cc_sm8250_exit(void)
+{
+	platform_driver_unregister(&gpu_cc_sm8250_driver);
+}
+module_exit(gpu_cc_sm8250_exit);
+
+MODULE_DESCRIPTION("QTI GPU_CC SM8250 Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.26.1

Re: [PATCH v3 11/14] clk: qcom: Add graphics clock controller driver for SM8250

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:42)
> Add support for the graphics clock controller found on SM8250
> based devices.
> 
> This is initially copied from the downstream kernel, but has
> been modified to more closely match the upstream sc7180 driver.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---

Applied to clk-next

[PATCH v3 12/14] dt-bindings: power: Add missing rpmpd rpmh regulator level

[Jonathan Marek]

Add RPMH_REGULATOR_LEVEL_SVS_L0, used by sm8250.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 include/dt-bindings/power/qcom-rpmpd.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index dc146e44228b..5e61eaf73bdd 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -55,6 +55,7 @@
 #define RPMH_REGULATOR_LEVEL_MIN_SVS	48
 #define RPMH_REGULATOR_LEVEL_LOW_SVS	64
 #define RPMH_REGULATOR_LEVEL_SVS	128
+#define RPMH_REGULATOR_LEVEL_SVS_L0	144
 #define RPMH_REGULATOR_LEVEL_SVS_L1	192
 #define RPMH_REGULATOR_LEVEL_SVS_L2	224
 #define RPMH_REGULATOR_LEVEL_NOM	256
-- 
2.26.1

Re: [PATCH v3 12/14] dt-bindings: power: Add missing rpmpd rpmh regulator level

[Rob Herring]

On Thu, 09 Jul 2020 09:52:43 -0400, Jonathan Marek wrote:
> Add RPMH_REGULATOR_LEVEL_SVS_L0, used by sm8250.
> 
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
>  include/dt-bindings/power/qcom-rpmpd.h | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v3 13/14] arm64: dts: qcom: add sm8150 GPU nodes

[Jonathan Marek]

This brings up the GPU. Tested on HDK855 by running vulkan CTS.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 136 +++++++++++++++++++++++++++
 1 file changed, 136 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index d117a64f591e..b65fd7027d1e 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -10,6 +10,7 @@
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,gcc-sm8150.h>
+#include <dt-bindings/clock/qcom,gpucc-sm8150.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -549,6 +550,141 @@ glink-edge {
 			};
 		};
 
+		gpu: gpu@2c00000 {
+			/*
+			 * note: the amd,imageon compatible makes it possible
+			 * to use the drm/msm driver without the display node,
+			 * make sure to remove it when display node is added
+			 */
+			compatible = "qcom,adreno-640.1",
+				     "qcom,adreno",
+				     "amd,imageon";
+			#stream-id-cells = <16>;
+
+			reg = <0 0x2c00000 0 0x40000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+			iommus = <&adreno_smmu 0 0x401>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			qcom,gmu = <&gmu>;
+
+			zap-shader {
+				memory-region = <&gpu_mem>;
+			};
+
+			/* note: downstream checks gpu binning for 675 Mhz */
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-675000000 {
+					opp-hz = /bits/ 64 <675000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+				};
+
+				opp-585000000 {
+					opp-hz = /bits/ 64 <585000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+				};
+
+				opp-499200000 {
+					opp-hz = /bits/ 64 <499200000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
+				};
+
+				opp-427000000 {
+					opp-hz = /bits/ 64 <427000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+				};
+
+				opp-345000000 {
+					opp-hz = /bits/ 64 <345000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+
+				opp-257000000 {
+					opp-hz = /bits/ 64 <257000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+				};
+			};
+		};
+
+		gmu: gmu@2c6a000 {
+			compatible="qcom,adreno-gmu-640.1", "qcom,adreno-gmu";
+
+			reg = <0 0x2c6a000 0 0x30000>,
+			      <0 0xb290000 0 0x10000>,
+			      <0 0xb490000 0 0x10000>;
+			reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
+
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_CX_GMU_CLK>,
+			         <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+			clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";
+
+			power-domains = <&gpucc GPU_CX_GDSC>,
+					<&gpucc GPU_GX_GDSC>;
+			power-domain-names = "cx", "gx";
+
+			iommus = <&adreno_smmu 5 0x400>;
+
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+				};
+			};
+		};
+
+		gpucc: clock-controller@2c90000 {
+			compatible = "qcom,sm8150-gpucc";
+			reg = <0 0x2c90000 0 0x9000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+			clock-names = "bi_tcxo",
+				      "gcc_gpu_gpll0_clk_src",
+				      "gcc_gpu_gpll0_div_clk_src";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		adreno_smmu: iommu@2ca0000 {
+			compatible = "qcom,sm8150-smmu-500", "arm,mmu-500";
+			reg = <0 0x2ca0000 0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 674 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+			         <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>;
+			clock-names = "ahb", "bus", "iface";
+
+			power-domains = <&gpucc GPU_CX_GDSC>;
+		};
+
 		tlmm: pinctrl@3100000 {
 			compatible = "qcom,sm8150-pinctrl";
 			reg = <0x0 0x03100000 0x0 0x300000>,
-- 
2.26.1

[PATCH v3 14/14] arm64: dts: qcom: add sm8250 GPU nodes

[Jonathan Marek]

This brings up the GPU. Tested on HDK865 by running vulkan CTS.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 143 +++++++++++++++++++++++++++
 1 file changed, 143 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 3564f233064c..636e2196138c 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-sm8250.h>
+#include <dt-bindings/clock/qcom,gpucc-sm8250.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-aoss-qmp.h>
@@ -1131,6 +1132,148 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
 			};
 		};
 
+		gpu: gpu@3d00000 {
+			/*
+			 * note: the amd,imageon compatible makes it possible
+			 * to use the drm/msm driver without the display node,
+			 * make sure to remove it when display node is added
+			 */
+			compatible = "qcom,adreno-650.2",
+				     "qcom,adreno",
+				     "amd,imageon";
+			#stream-id-cells = <16>;
+
+			reg = <0 0x3d00000 0 0x40000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+			iommus = <&adreno_smmu 0 0x401>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			qcom,gmu = <&gmu>;
+
+			zap-shader {
+				memory-region = <&gpu_mem>;
+			};
+
+			/* note: downstream checks gpu binning for 670 Mhz */
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-670000000 {
+					opp-hz = /bits/ 64 <670000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+				};
+
+				opp-587000000 {
+					opp-hz = /bits/ 64 <587000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+				};
+
+				opp-525000000 {
+					opp-hz = /bits/ 64 <525000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
+				};
+
+				opp-490000000 {
+					opp-hz = /bits/ 64 <490000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+				};
+
+				opp-441600000 {
+					opp-hz = /bits/ 64 <441600000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
+				};
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+
+				opp-305000000 {
+					opp-hz = /bits/ 64 <305000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+				};
+			};
+		};
+
+		gmu: gmu@3d6a000 {
+			compatible="qcom,adreno-gmu-650.2", "qcom,adreno-gmu";
+
+			reg = <0 0x3d6a000 0 0x30000>,
+			      <0 0x3de0000 0 0x10000>,
+			      <0 0xb290000 0 0x10000>,
+			      <0 0xb490000 0 0x10000>;
+			reg-names = "gmu", "rscc", "gmu_pdc", "gmu_pdc_seq";
+
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_CX_GMU_CLK>,
+			         <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+			clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";
+
+			power-domains = <&gpucc GPU_CX_GDSC>,
+					<&gpucc GPU_GX_GDSC>;
+			power-domain-names = "cx", "gx";
+
+			iommus = <&adreno_smmu 5 0x400>;
+
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+				};
+			};
+		};
+
+		gpucc: clock-controller@3d90000 {
+			compatible = "qcom,sm8250-gpucc";
+			reg = <0 0x3d90000 0 0x9000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+			clock-names = "bi_tcxo",
+				      "gcc_gpu_gpll0_clk_src",
+				      "gcc_gpu_gpll0_div_clk_src";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		adreno_smmu: iommu@3da0000 {
+			compatible = "qcom,sm8250-smmu-500", "arm,mmu-500";
+			reg = <0 0x3da0000 0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <2>;
+			interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>;
+			clock-names = "ahb", "bus", "iface";
+
+			power-domains = <&gpucc GPU_CX_GDSC>;
+		};
+
 		usb_1_hsphy: phy@88e3000 {
 			compatible = "qcom,sm8250-usb-hs-phy",
 				     "qcom,usb-snps-hs-7nm-phy";
-- 
2.26.1

Re: [PATCH v3 00/14] Enable GPU for SM8150 and SM8250

[Stephen Boyd]

Quoting Jonathan Marek (2020-07-09 06:52:31)
> This series adds the missing clock drivers and dts nodes to enable
> the GPU on both SM8150 and SM8250.
> 
> Note an extra drm/msm patch [1] is required for SM8250.
> 
> As noted by Dmitry, GMU init fails with newer firmware, needs this patch [2].
> 
> [1] https://patchwork.freedesktop.org/series/78968/
> [2] https://git.linaro.org/landing-teams/working/qualcomm/kernel.git/commit/?h=tracking-qcomlt-sm8250&id=01331f2ccbe7e6c4719dbe038a5fb496db32646d

Vinod, can you test this patch series? And Taniya, can you review it?

Re: [PATCH v3 00/14] Enable GPU for SM8150 and SM8250

[Dmitry Baryshkov]

On 21/07/2020 10:54, Stephen Boyd wrote:
> Quoting Jonathan Marek (2020-07-09 06:52:31)
>> This series adds the missing clock drivers and dts nodes to enable
>> the GPU on both SM8150 and SM8250.
>>
>> Note an extra drm/msm patch [1] is required for SM8250.
>>
>> As noted by Dmitry, GMU init fails with newer firmware, needs this patch [2].
>>
>> [1] https://patchwork.freedesktop.org/series/78968/
>> [2] https://git.linaro.org/landing-teams/working/qualcomm/kernel.git/commit/?h=tracking-qcomlt-sm8250&id=01331f2ccbe7e6c4719dbe038a5fb496db32646d
> 
> Vinod, can you test this patch series? And Taniya, can you review it?

On SM8250:

Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>


-- 
With best wishes
Dmitry