* [PATCH v2 0/3] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board.
@ 2020-06-25 17:37 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 1/3] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-06-25 17:37 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, paul.burton, paul, robh+dt, tsbogend,
ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
v1->v2:
1.Add DT node for LED.
2.Update defconfig for LED.
周琰杰 (Zhou Yanjie) (3):
MIPS: Ingenic: Add Ingenic X1830 support.
dt-bindings: MIPS: Add Ingenic X1830 based boards.
MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
.../devicetree/bindings/mips/ingenic/devices.yaml | 12 +-
arch/mips/boot/dts/ingenic/Makefile | 1 +
arch/mips/boot/dts/ingenic/cu1830-neo.dts | 168 ++++++++++++
arch/mips/boot/dts/ingenic/x1830.dtsi | 300 +++++++++++++++++++++
arch/mips/configs/cu1830-neo_defconfig | 123 +++++++++
arch/mips/jz4740/Kconfig | 10 +
6 files changed, 611 insertions(+), 3 deletions(-)
create mode 100644 arch/mips/boot/dts/ingenic/cu1830-neo.dts
create mode 100755 arch/mips/boot/dts/ingenic/x1830.dtsi
create mode 100644 arch/mips/configs/cu1830-neo_defconfig
--
2.11.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2 1/3] MIPS: Ingenic: Add Ingenic X1830 support.
2020-06-25 17:37 [PATCH v2 0/3] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
@ 2020-06-25 17:37 ` 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 3/3] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
2 siblings, 0 replies; 6+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-06-25 17:37 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, paul.burton, paul, robh+dt, tsbogend,
ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
No change.
arch/mips/boot/dts/ingenic/x1830.dtsi | 300 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 +
2 files changed, 306 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/x1830.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
new file mode 100644
index 000000000000..6d2d6f227b45
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/x1830-cgu.h>
+#include <dt-bindings/dma/x1830-dma.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1830";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1830-cgu@10000000 {
+ compatible = "ingenic,x1830-cgu";
+ reg = <0x10000000 0x100>;
+
+ #clock-cells = <1>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+ };
+
+ tcu: timer@10002000 {
+ compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu X1830_CLK_RTCLK
+ &cgu X1830_CLK_EXCLK
+ &cgu X1830_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+
+ wdt: watchdog@0 {
+ compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
+ reg = <0x0 0x10>;
+
+ clocks = <&tcu TCU_CLK_WDT>;
+ clock-names = "wdt";
+ };
+ };
+
+ rtc: rtc@10003000 {
+ compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
+ reg = <0x10003000 0x4c>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <32>;
+
+ clocks = <&cgu X1830_CLK_RTCLK>;
+ clock-names = "rtc";
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1830-pinctrl";
+ reg = <0x10010000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+
+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <60>;
+
+ clocks = <&cgu X1830_CLK_SMB0>;
+
+ status = "disabled";
+ };
+
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <59>;
+
+ clocks = <&cgu X1830_CLK_SMB1>;
+
+ status = "disabled";
+ };
+
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1830_CLK_SMB2>;
+
+ status = "disabled";
+ };
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ pdma: dma-controller@13420000 {
+ compatible = "ingenic,x1830-dma";
+ reg = <0x13420000 0x400
+ 0x13421000 0x40>;
+ #dma-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <10>;
+
+ clocks = <&cgu X1830_CLK_PDMA>;
+ };
+
+ mac: ethernet@134b0000 {
+ compatible = "ingenic,x1830-mac", "snps,dwmac";
+ reg = <0x134b0000 0x2000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <55>;
+ interrupt-names = "macirq";
+
+ clocks = <&cgu X1830_CLK_MAC>;
+ clock-names = "stmmaceth";
+
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+
+ msc0: mmc@13450000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13450000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <37>;
+
+ clocks = <&cgu X1830_CLK_MSC0>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC0_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ msc1: mmc@13460000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13460000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+
+ clocks = <&cgu X1830_CLK_MSC1>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC1_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 9c2e8c15bb97..cd0ddb52da99 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -50,3 +50,9 @@ config MACH_X1000
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1830
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
--
2.11.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards.
2020-06-25 17:37 [PATCH v2 0/3] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 1/3] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
@ 2020-06-25 17:37 ` 周琰杰 (Zhou Yanjie)
2020-07-14 2:32 ` Rob Herring
2020-06-25 17:37 ` [PATCH v2 3/3] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
2 siblings, 1 reply; 6+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-06-25 17:37 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, paul.burton, paul, robh+dt, tsbogend,
ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Add bindings for Ingenic X1830 based board, prepare for later dts.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
No change.
Documentation/devicetree/bindings/mips/ingenic/devices.yaml | 12 +++++++++---
1 file changed, 9 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
index d1175030781a..feb695be9f66 100644
--- a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
+++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
@@ -8,7 +8,8 @@ title: Ingenic XBurst based Platforms Device Tree Bindings
maintainers:
- 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
-description: |
+
+description:
Devices with a Ingenic XBurst CPU shall have the following properties.
properties:
@@ -32,8 +33,13 @@ properties:
- const: img,ci20
- const: ingenic,jz4780
- - description: YSH & ATIL General Board CU Neo
+ - description: YSH & ATIL General Board, CU1000 Module with Neo Backplane
items:
- const: yna,cu1000-neo
- - const: ingenic,x1000
+ - const: ingenic,x1000e
+
+ - description: YSH & ATIL General Board, CU1830 Module with Neo Backplane
+ items:
+ - const: yna,cu1830-neo
+ - const: ingenic,x1830
...
--
2.11.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 3/3] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
2020-06-25 17:37 [PATCH v2 0/3] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 1/3] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards 周琰杰 (Zhou Yanjie)
@ 2020-06-25 17:37 ` 周琰杰 (Zhou Yanjie)
2 siblings, 0 replies; 6+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-06-25 17:37 UTC (permalink / raw)
To: linux-mips
Cc: linux-kernel, devicetree, paul.burton, paul, robh+dt, tsbogend,
ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Add a device tree and a defconfig for the Ingenic X1830 based
YSH & ATIL CU Neo board.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
1.Add DT node for LED.
2.Update defconfig for LED.
arch/mips/boot/dts/ingenic/Makefile | 1 +
arch/mips/boot/dts/ingenic/cu1830-neo.dts | 168 ++++++++++++++++++++++++++++++
arch/mips/configs/cu1830-neo_defconfig | 123 ++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 4 +
4 files changed, 296 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/cu1830-neo.dts
create mode 100644 arch/mips/configs/cu1830-neo_defconfig
diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
index e1654291a7b0..c33434fad007 100644
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_JZ4740_QI_LB60) += qi_lb60.dtb
dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb
+dtb-$(CONFIG_X1830_CU1830_NEO) += cu1830-neo.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
new file mode 100644
index 000000000000..605160927fe6
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1830.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "yna,cu1830-neo", "ingenic,x1830";
+ model = "YSH & ATIL General Board CU1830-Neo";
+
+ aliases {
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x08000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-0 {
+ gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ wlan_pwrseq: msc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+
+ reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&exclk {
+ clock-frequency = <24000000>;
+};
+
+&tcu {
+ /* 1500 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+ assigned-clock-rates = <1500000>, <1500000>;
+
+ /* Use channel #0 for the system timer channel #2 for the clocksource */
+ ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_i2c0>;
+
+ ads7830: adc@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart1>;
+};
+
+&mac {
+ status = "okay";
+
+ phy-mode = "rmii";
+ phy-handle = <&ip101gr>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_mac>;
+
+ snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+ status = "okay";
+
+ ip101gr: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&msc0 {
+ status = "okay";
+
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc0>;
+
+ non-removable;
+};
+
+&msc1 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc1>;
+
+ non-removable;
+
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ ap6212a: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpc>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ brcm,drive-strength = <10>;
+ };
+};
+
+&pinctrl {
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-pull-up;
+ };
+
+ pins_uart1: uart1 {
+ function = "uart1";
+ groups = "uart1-data";
+ bias-pull-up;
+ };
+
+ pins_mac: mac {
+ function = "mac";
+ groups = "mac";
+ bias-disable;
+ };
+
+ pins_msc0: msc0 {
+ function = "mmc0";
+ groups = "mmc0-1bit", "mmc0-4bit";
+ bias-disable;
+ };
+
+ pins_msc1: msc1 {
+ function = "mmc1";
+ groups = "mmc1-1bit", "mmc1-4bit";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/configs/cu1830-neo_defconfig b/arch/mips/configs/cu1830-neo_defconfig
new file mode 100644
index 000000000000..cbfb62900273
--- /dev/null
+++ b/arch/mips/configs/cu1830-neo_defconfig
@@ -0,0 +1,123 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1830_CU1830_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_BRCMFMAC=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index cd0ddb52da99..6c065dcaeff8 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -27,6 +27,10 @@ config X1000_CU1000_NEO
bool "YSH & ATIL CU1000 Module with Neo backplane"
select MACH_X1000
+config X1830_CU1830_NEO
+ bool "YSH & ATIL CU1830 Module with Neo backplane"
+ select MACH_X1830
+
endchoice
config MACH_JZ4740
--
2.11.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards.
2020-06-25 17:37 ` [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards 周琰杰 (Zhou Yanjie)
@ 2020-07-14 2:32 ` Rob Herring
2020-07-14 3:40 ` Zhou Yanjie
0 siblings, 1 reply; 6+ messages in thread
From: Rob Herring @ 2020-07-14 2:32 UTC (permalink / raw)
To: 周琰杰 (Zhou Yanjie)
Cc: linux-mips, linux-kernel, devicetree, paul.burton, paul,
tsbogend, ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu,
yanfei.li, sernia.zhou, zhenwenjin
On Fri, Jun 26, 2020 at 01:37:15AM +0800, 周琰杰 (Zhou Yanjie) wrote:
> Add bindings for Ingenic X1830 based board, prepare for later dts.
>
> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
>
> Notes:
> v1->v2:
> No change.
>
> Documentation/devicetree/bindings/mips/ingenic/devices.yaml | 12 +++++++++---
> 1 file changed, 9 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
> index d1175030781a..feb695be9f66 100644
> --- a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
> +++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
> @@ -8,7 +8,8 @@ title: Ingenic XBurst based Platforms Device Tree Bindings
>
> maintainers:
> - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> -description: |
> +
> +description:
> Devices with a Ingenic XBurst CPU shall have the following properties.
>
> properties:
> @@ -32,8 +33,13 @@ properties:
> - const: img,ci20
> - const: ingenic,jz4780
>
> - - description: YSH & ATIL General Board CU Neo
> + - description: YSH & ATIL General Board, CU1000 Module with Neo Backplane
> items:
> - const: yna,cu1000-neo
> - - const: ingenic,x1000
> + - const: ingenic,x1000e
What's this change? You can't just change bindings.
> +
> + - description: YSH & ATIL General Board, CU1830 Module with Neo Backplane
> + items:
> + - const: yna,cu1830-neo
> + - const: ingenic,x1830
> ...
> --
> 2.11.0
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards.
2020-07-14 2:32 ` Rob Herring
@ 2020-07-14 3:40 ` Zhou Yanjie
0 siblings, 0 replies; 6+ messages in thread
From: Zhou Yanjie @ 2020-07-14 3:40 UTC (permalink / raw)
To: Rob Herring
Cc: linux-mips, linux-kernel, devicetree, paul.burton, paul,
tsbogend, ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu,
yanfei.li, sernia.zhou, zhenwenjin
Hi Rob,
在 2020/7/14 上午10:32, Rob Herring 写道:
> On Fri, Jun 26, 2020 at 01:37:15AM +0800, 周琰杰 (Zhou Yanjie) wrote:
>> Add bindings for Ingenic X1830 based board, prepare for later dts.
>>
>> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>> ---
>>
>> Notes:
>> v1->v2:
>> No change.
>>
>> Documentation/devicetree/bindings/mips/ingenic/devices.yaml | 12 +++++++++---
>> 1 file changed, 9 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
>> index d1175030781a..feb695be9f66 100644
>> --- a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
>> +++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
>> @@ -8,7 +8,8 @@ title: Ingenic XBurst based Platforms Device Tree Bindings
>>
>> maintainers:
>> - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>> -description: |
>> +
>> +description:
>> Devices with a Ingenic XBurst CPU shall have the following properties.
>>
>> properties:
>> @@ -32,8 +33,13 @@ properties:
>> - const: img,ci20
>> - const: ingenic,jz4780
>>
>> - - description: YSH & ATIL General Board CU Neo
>> + - description: YSH & ATIL General Board, CU1000 Module with Neo Backplane
>> items:
>> - const: yna,cu1000-neo
>> - - const: ingenic,x1000
>> + - const: ingenic,x1000e
> What's this change? You can't just change bindings.
This is my fault, I will add the modification of the corresponding dts
file in the next version.
Thanks and best regards!
>> +
>> + - description: YSH & ATIL General Board, CU1830 Module with Neo Backplane
>> + items:
>> + - const: yna,cu1830-neo
>> + - const: ingenic,x1830
>> ...
>> --
>> 2.11.0
>>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-07-14 3:40 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-25 17:37 [PATCH v2 0/3] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 1/3] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
2020-06-25 17:37 ` [PATCH v2 2/3] dt-bindings: MIPS: Add Ingenic X1830 based boards 周琰杰 (Zhou Yanjie)
2020-07-14 2:32 ` Rob Herring
2020-07-14 3:40 ` Zhou Yanjie
2020-06-25 17:37 ` [PATCH v2 3/3] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.