* Re: [PATCH v2 3/3] arm64: dts: rockchip: add rk3318 A95X Z2 board
@ 2020-08-03 21:41 ` Robin Murphy
0 siblings, 0 replies; 23+ messages in thread
From: Robin Murphy @ 2020-08-03 21:41 UTC (permalink / raw)
To: Johan Jonker, heiko
Cc: devicetree, robh+dt, linux-kernel, linux-arm-kernel, linux-rockchip
On 2020-07-18 11:53, Johan Jonker wrote:
> The rk3318 A95X Z2 boards are sold as TV box.
> No further documentation is given, but from the dts files
> extracted it seems that the rk3318 processor is simulair
> to the rk3328. This dts file contains only the basic nodes
> that have support in the mainline kernel.
>
> Features:
>
> CPU: RK3318 Quad-Core Cortex-A53
> GPU: Mali-450
> RAM: 2/4GB DDR3
> ROM: EMMC 16/32/64GB
> HDMI: HDMI 2.0a for 4k@60Hz
> Ethernet: 10/100M standard RJ-45
> WiFi: 2.4G+5G WIFI, 802.11 b/g/n
> Bluetooth: 4.0
> 1 x USB 3.0
> 1 x USB 2.0
> 1 x Micro SD card slot
> 1 x SPDIF
> 1 x AV
> 1 x DC IN
>
> Signed-off-by: Johan Jonker <jbx6244@gmail.com>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts | 393 ++++++++++++++++++++++++
> 2 files changed, 394 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index b87b1f773..aa508bc4a 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -2,6 +2,7 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
> new file mode 100644
> index 000000000..413418ea1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
> @@ -0,0 +1,393 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include "rk3328.dtsi"
> +
> +/ {
> + model = "A95X Z2";
> + compatible = "zkmagic,a95x-z2", "rockchip,rk3318";
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + vol-up-key {
> + label = "volume up";
> + linux,code = <KEY_VOLUMEUP>;
Really? If as usual this is actually the recovery button hidden inside
the box, it's somewhat questionable whether it's worth describing in DT
at all. At the very least it should probably be presented as something
more realistic than half a volume control.
> + press-threshold-microvolt = <17000>;
> + };
> + };
> +
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&ir_int>;
> + pinctrl-names = "default";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&cyx_led_pin>;
> + pinctrl-names = "default";
> +
> + cyx_led: led-0 {
What needs a phandle to this node to warrant a label?
> + default-state = "on";
> + gpios = <&gpio2 RK_PC7 GPIO_ACTIVE_LOW>;
> + label = "CYX_LED";
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-0 = <&wifi_enable_h>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> + };
> +
> + spdif-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "spdif";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&spdif>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&spdif_out>;
> + };
> + };
> +
> + spdif_out: spdif-out {
> + compatible = "linux,spdif-dit";
> + #sound-dai-cells = <0>;
> + };
> +
> + /* Power tree */
> + regulators {
Don't create fake "buses" for regulators, especially if they don't even
contain most of the regulators anyway.
> + compatible = "simple-mfd";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vccio_1v8_reg: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "vccio_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vccio_3v3_reg: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "vccio_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> +
> + vcc_otg_vbus: otg-vbus-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&otg_vbus_drv>;
> + pinctrl-names = "default";
> + regulator-name = "vcc_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + };
> +
> + vcc_phy: vcc-phy-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_phy";
> + regulator-always-on;
> + regulator-boot-on;
> + };
Is this actually a distinct regulator? The reference design has the
internal FEPHY block powered pretty much directly from the general 1V8
and 1V0 supplies that also power USB/HDMI/etc., so I'd rather expect
low-end boxes to follow suit. Either way there doesn't seem to be a
great deal of value in describing something with no controls, no voltage
information, and no connection to the power tree.
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&sdmmc0m1_gpio>;
> + pinctrl-names = "default";
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vccio_3v3_reg>;
> + };
> +
> + vdd_arm: vdd-arm {
> + compatible = "pwm-regulator";
> + pwms = <&pwm0 0 5000 1>;
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm1 0 5000 1>;
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&analog_sound {
> + status = "okay";
> +};
> +
> +&codec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu0_opp_table {
> + opp-1200000000 {
> + status = "disabled";
> + };
> +
> + opp-1296000000 {
> + status = "disabled";
> + };
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + non-removable;
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&gmac2phy {
> + assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
> + assigned-clock-rate = <50000000>;
> + assigned-clocks = <&cru SCLK_MAC2PHY>;
> + clock_in_out = "output";
> + phy-supply = <&vcc_phy>;
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_log>;
> +};
> +
> +&hdmi {
> + ddc-i2c-scl-high-time-ns = <9625>;
> + ddc-i2c-scl-low-time-ns = <10000>;
> + status = "okay";
> +};
> +
> +&hdmiphy {
> + status = "okay";
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2s0 {
> + status = "okay";
> +};
> +
> +&i2s1 {
> + status = "okay";
> +};
> +
> +&io_domains {
> + pmuio-supply = <&vccio_3v3_reg>;
> + vccio1-supply = <&vccio_3v3_reg>;
> + vccio2-supply = <&vccio_1v8_reg>;
> + vccio3-supply = <&vccio_3v3_reg>;
> + vccio4-supply = <&vccio_1v8_reg>;
> + vccio5-supply = <&vccio_3v3_reg>;
> + vccio6-supply = <&vccio_3v3_reg>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + ir {
> + ir_int: ir-int {
> + rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + cyx_led_pin: cyx-led-pin {
> + rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pwm0 {
> + pwm0_pin_pull_up: pwm0-pin-pull-up {
> + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_up>;
> + };
> + };
> +
> + pwm1 {
> + pwm1_pin_pull_up: pwm1-pin-pull-up {
> + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_up>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc1 {
> + clk_32k_out: clk-32k-out {
> + rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + otg_vbus_drv: otg-vbus-drv {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + pinctrl-0 = <&pwm0_pin_pull_up>;
> + pinctrl-names = "active";
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-0 = <&pwm1_pin_pull_up>;
> + pinctrl-names = "active";
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vccio_1v8_reg>;
> + status = "okay";
> +};
> +
> +&sdio {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + max-frequency = <125000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &clk_32k_out>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + disable-wp;
> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
> + pinctrl-names = "default";
> + vmmc-supply = <&vcc_sd>;
> + status = "okay";
> +};
> +
> +&spdif {
> + pinctrl-0 = <&spdifm0_tx>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&soc_crit {
> + temperature = <115000>; /* millicelsius */
> +};
> +
> +&target {
> + temperature = <105000>; /* millicelsius */
> +};
> +
> +&threshold {
> + temperature = <90000>; /* millicelsius */
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-temp = <120000>;
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +
> + u2phy_host: host-port {
Just refer to the ports normally by label rather than duplicate a random
snippet of DTSI hierarchy - I'm not sure why this particular pattern
seems to get copied around so much.
Robin.
> + status = "okay";
> + };
> +
> + u2phy_otg: otg-port {
> + phy-supply = <&vcc_otg_vbus>;
> + status = "okay";
> + };
> +};
> +
> +&uart0 {
> + pinctrl-0 = <&uart0_xfer &uart0_cts>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb20_otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&vop {
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH v2 3/3] arm64: dts: rockchip: add rk3318 A95X Z2 board
@ 2020-08-03 21:41 ` Robin Murphy
0 siblings, 0 replies; 23+ messages in thread
From: Robin Murphy @ 2020-08-03 21:41 UTC (permalink / raw)
To: Johan Jonker, heiko-4mtYJXux2i+zQB+pC5nmwQ
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 2020-07-18 11:53, Johan Jonker wrote:
> The rk3318 A95X Z2 boards are sold as TV box.
> No further documentation is given, but from the dts files
> extracted it seems that the rk3318 processor is simulair
> to the rk3328. This dts file contains only the basic nodes
> that have support in the mainline kernel.
>
> Features:
>
> CPU: RK3318 Quad-Core Cortex-A53
> GPU: Mali-450
> RAM: 2/4GB DDR3
> ROM: EMMC 16/32/64GB
> HDMI: HDMI 2.0a for 4k@60Hz
> Ethernet: 10/100M standard RJ-45
> WiFi: 2.4G+5G WIFI, 802.11 b/g/n
> Bluetooth: 4.0
> 1 x USB 3.0
> 1 x USB 2.0
> 1 x Micro SD card slot
> 1 x SPDIF
> 1 x AV
> 1 x DC IN
>
> Signed-off-by: Johan Jonker <jbx6244-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts | 393 ++++++++++++++++++++++++
> 2 files changed, 394 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index b87b1f773..aa508bc4a 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -2,6 +2,7 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
> new file mode 100644
> index 000000000..413418ea1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
> @@ -0,0 +1,393 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include "rk3328.dtsi"
> +
> +/ {
> + model = "A95X Z2";
> + compatible = "zkmagic,a95x-z2", "rockchip,rk3318";
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> +
> + vol-up-key {
> + label = "volume up";
> + linux,code = <KEY_VOLUMEUP>;
Really? If as usual this is actually the recovery button hidden inside
the box, it's somewhat questionable whether it's worth describing in DT
at all. At the very least it should probably be presented as something
more realistic than half a volume control.
> + press-threshold-microvolt = <17000>;
> + };
> + };
> +
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&ir_int>;
> + pinctrl-names = "default";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&cyx_led_pin>;
> + pinctrl-names = "default";
> +
> + cyx_led: led-0 {
What needs a phandle to this node to warrant a label?
> + default-state = "on";
> + gpios = <&gpio2 RK_PC7 GPIO_ACTIVE_LOW>;
> + label = "CYX_LED";
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-0 = <&wifi_enable_h>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> + };
> +
> + spdif-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "spdif";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&spdif>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&spdif_out>;
> + };
> + };
> +
> + spdif_out: spdif-out {
> + compatible = "linux,spdif-dit";
> + #sound-dai-cells = <0>;
> + };
> +
> + /* Power tree */
> + regulators {
Don't create fake "buses" for regulators, especially if they don't even
contain most of the regulators anyway.
> + compatible = "simple-mfd";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vccio_1v8_reg: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "vccio_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vccio_3v3_reg: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "vccio_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> +
> + vcc_otg_vbus: otg-vbus-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&otg_vbus_drv>;
> + pinctrl-names = "default";
> + regulator-name = "vcc_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + };
> +
> + vcc_phy: vcc-phy-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_phy";
> + regulator-always-on;
> + regulator-boot-on;
> + };
Is this actually a distinct regulator? The reference design has the
internal FEPHY block powered pretty much directly from the general 1V8
and 1V0 supplies that also power USB/HDMI/etc., so I'd rather expect
low-end boxes to follow suit. Either way there doesn't seem to be a
great deal of value in describing something with no controls, no voltage
information, and no connection to the power tree.
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&sdmmc0m1_gpio>;
> + pinctrl-names = "default";
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vccio_3v3_reg>;
> + };
> +
> + vdd_arm: vdd-arm {
> + compatible = "pwm-regulator";
> + pwms = <&pwm0 0 5000 1>;
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm1 0 5000 1>;
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&analog_sound {
> + status = "okay";
> +};
> +
> +&codec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu0_opp_table {
> + opp-1200000000 {
> + status = "disabled";
> + };
> +
> + opp-1296000000 {
> + status = "disabled";
> + };
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + non-removable;
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&gmac2phy {
> + assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
> + assigned-clock-rate = <50000000>;
> + assigned-clocks = <&cru SCLK_MAC2PHY>;
> + clock_in_out = "output";
> + phy-supply = <&vcc_phy>;
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_log>;
> +};
> +
> +&hdmi {
> + ddc-i2c-scl-high-time-ns = <9625>;
> + ddc-i2c-scl-low-time-ns = <10000>;
> + status = "okay";
> +};
> +
> +&hdmiphy {
> + status = "okay";
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2s0 {
> + status = "okay";
> +};
> +
> +&i2s1 {
> + status = "okay";
> +};
> +
> +&io_domains {
> + pmuio-supply = <&vccio_3v3_reg>;
> + vccio1-supply = <&vccio_3v3_reg>;
> + vccio2-supply = <&vccio_1v8_reg>;
> + vccio3-supply = <&vccio_3v3_reg>;
> + vccio4-supply = <&vccio_1v8_reg>;
> + vccio5-supply = <&vccio_3v3_reg>;
> + vccio6-supply = <&vccio_3v3_reg>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + ir {
> + ir_int: ir-int {
> + rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + cyx_led_pin: cyx-led-pin {
> + rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pwm0 {
> + pwm0_pin_pull_up: pwm0-pin-pull-up {
> + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_up>;
> + };
> + };
> +
> + pwm1 {
> + pwm1_pin_pull_up: pwm1-pin-pull-up {
> + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_up>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc1 {
> + clk_32k_out: clk-32k-out {
> + rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + otg_vbus_drv: otg-vbus-drv {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + pinctrl-0 = <&pwm0_pin_pull_up>;
> + pinctrl-names = "active";
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-0 = <&pwm1_pin_pull_up>;
> + pinctrl-names = "active";
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vccio_1v8_reg>;
> + status = "okay";
> +};
> +
> +&sdio {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + max-frequency = <125000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &clk_32k_out>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + disable-wp;
> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
> + pinctrl-names = "default";
> + vmmc-supply = <&vcc_sd>;
> + status = "okay";
> +};
> +
> +&spdif {
> + pinctrl-0 = <&spdifm0_tx>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&soc_crit {
> + temperature = <115000>; /* millicelsius */
> +};
> +
> +&target {
> + temperature = <105000>; /* millicelsius */
> +};
> +
> +&threshold {
> + temperature = <90000>; /* millicelsius */
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-temp = <120000>;
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +
> + u2phy_host: host-port {
Just refer to the ports normally by label rather than duplicate a random
snippet of DTSI hierarchy - I'm not sure why this particular pattern
seems to get copied around so much.
Robin.
> + status = "okay";
> + };
> +
> + u2phy_otg: otg-port {
> + phy-supply = <&vcc_otg_vbus>;
> + status = "okay";
> + };
> +};
> +
> +&uart0 {
> + pinctrl-0 = <&uart0_xfer &uart0_cts>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb20_otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&vop {
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
>
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH v2 3/3] arm64: dts: rockchip: add rk3318 A95X Z2 board
@ 2020-08-04 15:54 ` Johan Jonker
0 siblings, 0 replies; 23+ messages in thread
From: Johan Jonker @ 2020-08-04 15:54 UTC (permalink / raw)
To: Robin Murphy, heiko
Cc: devicetree, robh+dt, linux-kernel, linux-arm-kernel, linux-rockchip
Hi Robin,
Thank you for your review.
Added some questions in return.
This dts file seems to be some sort of variation of
rk3328-box-liantong.dtsi in the manufacturer tree. Depending on the
design the vendor then changes the wifi chip or removes the spdif
connector to save some cost.
On 8/3/20 11:41 PM, Robin Murphy wrote:
> On 2020-07-18 11:53, Johan Jonker wrote:
>> The rk3318 A95X Z2 boards are sold as TV box.
>> No further documentation is given, but from the dts files
>> extracted it seems that the rk3318 processor is simulair
>> to the rk3328. This dts file contains only the basic nodes
>> that have support in the mainline kernel.
>>
>> Features:
>>
>> CPU: RK3318 Quad-Core Cortex-A53
>> GPU: Mali-450
>> RAM: 2/4GB DDR3
>> ROM: EMMC 16/32/64GB
>> HDMI: HDMI 2.0a for 4k@60Hz
>> Ethernet: 10/100M standard RJ-45
>> WiFi: 2.4G+5G WIFI, 802.11 b/g/n
>> Bluetooth: 4.0
>> 1 x USB 3.0
>> 1 x USB 2.0
>> 1 x Micro SD card slot
>> 1 x SPDIF
>> 1 x AV
>> 1 x DC IN
>>
>> Signed-off-by: Johan Jonker <jbx6244@gmail.com>
>> ---
>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>> arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts | 393
>> ++++++++++++++++++++++++
>> 2 files changed, 394 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>> b/arch/arm64/boot/dts/rockchip/Makefile
>> index b87b1f773..aa508bc4a 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -2,6 +2,7 @@
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> new file mode 100644
>> index 000000000..413418ea1
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> @@ -0,0 +1,393 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/input/input.h>
>> +#include "rk3328.dtsi"
>> +
>> +/ {
>> + model = "A95X Z2";
>> + compatible = "zkmagic,a95x-z2", "rockchip,rk3318";
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + adc-keys {
>> + compatible = "adc-keys";
>> + io-channels = <&saradc 0>;
>> + io-channel-names = "buttons";
>> + keyup-threshold-microvolt = <1800000>;
>> + poll-interval = <100>;
>> +
>> + vol-up-key {
>> + label = "volume up";
>> + linux,code = <KEY_VOLUMEUP>;
>
> Really? If as usual this is actually the recovery button hidden inside
> the box, it's somewhat questionable whether it's worth describing in DT
> at all. At the very least it should probably be presented as something
> more realistic than half a volume control.
Dts use is not limited to a mainline kernel setting. In Android that
<KEY_VOLUMEUP> seem to be a standard way needed to enter a menu. Then
make it as complete as possible to make it work.
What would be your realistic key proposal?
>
>> + press-threshold-microvolt = <17000>;
>> + };
>> + };
>> +
>> + ir-receiver {
>> + compatible = "gpio-ir-receiver";
>> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&ir_int>;
>> + pinctrl-names = "default";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <&cyx_led_pin>;
>> + pinctrl-names = "default";
>> +
>> + cyx_led: led-0 {
>
> What needs a phandle to this node to warrant a label?
Without repeating previous discussions, I made a proposal that was
approved. So we just stick to that set of rules consequently.
A little explanation:
With the conversion to yaml a preferred nodename was introduced.
Legacy Rockchip node names were sort of free style and causing the
dts-checker to produce a flood of warnings.
The led properties are described in 2 places, under leds and under pinctrl.
To improve the readability given the legacy and to prevent the
disconnect between schematics, leds and pinctrl we add a label with a
consistent name.
Fix with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
>
>> + default-state = "on";
>> + gpios = <&gpio2 RK_PC7 GPIO_ACTIVE_LOW>;
>> + label = "CYX_LED";
This label with capital letters is used by an Android app, so keep it.
>> + };
>> + };
>> +
>> + sdio_pwrseq: sdio-pwrseq {
>> + compatible = "mmc-pwrseq-simple";
>> + pinctrl-0 = <&wifi_enable_h>;
>> + pinctrl-names = "default";
>> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + spdif-sound {
>> + compatible = "simple-audio-card";
>> + simple-audio-card,name = "spdif";
Some programs don't like long names here.
Recently I see others also use "SPDIF".
Should I change?
Currently for rk3328 we have: "Analog" and "HDMI"
Is there a standard?
Please advise.
>> +
>> + simple-audio-card,cpu {
>> + sound-dai = <&spdif>;
>> + };
>> +
>> + simple-audio-card,codec {
>> + sound-dai = <&spdif_out>;
>> + };
>> + };
>> +
>> + spdif_out: spdif-out {
>> + compatible = "linux,spdif-dit";
>> + #sound-dai-cells = <0>;
>> + };
>> +
>> + /* Power tree */
>> + regulators {
>
> Don't create fake "buses" for regulators, especially if they don't even
> contain most of the regulators anyway.
Agree.
The original reason was not given.
vccio_1v8_reg and vccio_3v3_reg are used mostly in &io_domains.
Is there a dependency requirement that both must be probed/enabled
before being used?
Without these regulators in a bus should we then add a vcc-sys-regulator
for a complete supply chain?
vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
>
>> + compatible = "simple-mfd";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + vccio_1v8_reg: regulator@0 {
>> + compatible = "regulator-fixed";
>> + reg = <0>;
>> + regulator-name = "vccio_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> +
>> + vccio_3v3_reg: regulator@1 {
>> + compatible = "regulator-fixed";
>> + reg = <1>;
>> + regulator-name = "vccio_3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> + };
>> +
>> + vcc_otg_vbus: otg-vbus-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
>> + pinctrl-0 = <&otg_vbus_drv>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + enable-active-high;
>> + };
>> +
>> + vcc_phy: vcc-phy-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc_phy";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>
> Is this actually a distinct regulator? The reference design has the
> internal FEPHY block powered pretty much directly from the general 1V8
> and 1V0 supplies that also power USB/HDMI/etc., so I'd rather expect
> low-end boxes to follow suit. Either way there doesn't seem to be a
> great deal of value in describing something with no controls, no voltage
> information, and no connection to the power tree.
Agree.
phy-supply appears to be an optional property, so removing it is
possible. It shows up in rk3328-roc-cc.dts and rk3328-evb.dts.
What does the maintainer prefer? Remove or not?
>
>> +
>> + vcc_sd: sdmmc-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&sdmmc0m1_gpio>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_sd";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + vin-supply = <&vccio_3v3_reg>;
>> + };
>> +
>> + vdd_arm: vdd-arm {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm0 0 5000 1>;
>> + regulator-name = "vdd_arm";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + vdd_log: vdd-log {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm1 0 5000 1>;
>> + regulator-name = "vdd_log";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +};
>> +
>> +&analog_sound {
>> + status = "okay";
>> +};
>> +
>> +&codec {
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu1 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu2 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu3 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu0_opp_table {
>> + opp-1200000000 {
>> + status = "disabled";
>> + };
>> +
>> + opp-1296000000 {
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&emmc {
>> + bus-width = <8>;
>> + cap-mmc-highspeed;
>> + non-removable;
>> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> +};
>> +
>> +&gmac2phy {
>> + assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
>> + assigned-clock-rate = <50000000>;
>> + assigned-clocks = <&cru SCLK_MAC2PHY>;
>> + clock_in_out = "output";
>> + phy-supply = <&vcc_phy>;
Remove or not?
>> + status = "okay";
>> +};
>> +
>> +&gpu {
>> + mali-supply = <&vdd_log>;
>> +};
>> +
>> +&hdmi {
>> + ddc-i2c-scl-high-time-ns = <9625>;
>> + ddc-i2c-scl-low-time-ns = <10000>;
>> + status = "okay";
>> +};
>> +
>> +&hdmiphy {
>> + status = "okay";
>> +};
>> +
>> +&hdmi_sound {
>> + status = "okay";
>> +};
>> +
>> +&i2s0 {
>> + status = "okay";
>> +};
>> +
>> +&i2s1 {
>> + status = "okay";
>> +};
>> +
>> +&io_domains {
>> + pmuio-supply = <&vccio_3v3_reg>;
>> + vccio1-supply = <&vccio_3v3_reg>;
>> + vccio2-supply = <&vccio_1v8_reg>;
>> + vccio3-supply = <&vccio_3v3_reg>;
>> + vccio4-supply = <&vccio_1v8_reg>;
>> + vccio5-supply = <&vccio_3v3_reg>;
>> + vccio6-supply = <&vccio_3v3_reg>;
>> + status = "okay";
>> +};
>> +
>> +&pinctrl {
>> + ir {
>> + ir_int: ir-int {
>> + rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + leds {
>> + cyx_led_pin: cyx-led-pin {
>> + rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + pwm0 {
>> + pwm0_pin_pull_up: pwm0-pin-pull-up {
>> + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + pwm1 {
>> + pwm1_pin_pull_up: pwm1-pin-pull-up {
>> + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + sdio-pwrseq {
>> + wifi_enable_h: wifi-enable-h {
>> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + sdmmc1 {
>> + clk_32k_out: clk-32k-out {
>> + rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + usb {
>> + host_vbus_drv: host-vbus-drv {
>> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> +
>> + otg_vbus_drv: otg-vbus-drv {
>> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +};
>> +
>> +&pwm0 {
>> + pinctrl-0 = <&pwm0_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&pwm1 {
>> + pinctrl-0 = <&pwm1_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&saradc {
>> + vref-supply = <&vccio_1v8_reg>;
>> + status = "okay";
>> +};
>> +
>> +&sdio {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + cap-sdio-irq;
>> + keep-power-in-suspend;
>> + max-frequency = <125000000>;
>> + mmc-pwrseq = <&sdio_pwrseq>;
>> + non-removable;
>> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &clk_32k_out>;
>> + pinctrl-names = "default";
>> + sd-uhs-sdr104;
>> + status = "okay";
>> +};
>> +
>> +&sdmmc {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + disable-wp;
This is from the manufacturer tree for a micro SD card. Remove or not?
Please advise.
>> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
>> + pinctrl-names = "default";
>> + vmmc-supply = <&vcc_sd>;
>> + status = "okay";
>> +};
>> +
>> +&spdif {
>> + pinctrl-0 = <&spdifm0_tx>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&soc_crit {
>> + temperature = <115000>; /* millicelsius */
>> +};
>> +
>> +&target {
>> + temperature = <105000>; /* millicelsius */
>> +};
>> +
>> +&threshold {
>> + temperature = <90000>; /* millicelsius */
>> +};
>> +
>> +&tsadc {
>> + rockchip,hw-tshut-temp = <120000>;
>> + status = "okay";
>> +};
>> +
>> +&u2phy {
>> + status = "okay";
>> +
>> + u2phy_host: host-port {
>
> Just refer to the ports normally by label rather than duplicate a random
> snippet of DTSI hierarchy - I'm not sure why this particular pattern
> seems to get copied around so much.
Here the node labels start with the same letters and the result will
stay together. In other cases it will scatter all over the dts file and
affects the readability. I just followed the manufacturer's example. If
the maintainer agrees then I'll change.
>
> Robin.
>
>> + status = "okay";
>> + };
>> +
>> + u2phy_otg: otg-port {
>> + phy-supply = <&vcc_otg_vbus>;
>> + status = "okay";
>> + };
>> +};
>> +
>> +&uart0 {
>> + pinctrl-0 = <&uart0_xfer &uart0_cts>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + status = "okay";
>> +};
>> +
>> +&usb20_otg {
>> + dr_mode = "host";
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ehci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ohci {
>> + status = "okay";
>> +};
>> +
>> +&vop {
>> + status = "okay";
>> +};
>> +
>> +&vop_mmu {
>> + status = "okay";
>> +};
>>
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH v2 3/3] arm64: dts: rockchip: add rk3318 A95X Z2 board
@ 2020-08-04 15:54 ` Johan Jonker
0 siblings, 0 replies; 23+ messages in thread
From: Johan Jonker @ 2020-08-04 15:54 UTC (permalink / raw)
To: Robin Murphy, heiko
Cc: devicetree, robh+dt, linux-kernel, linux-arm-kernel, linux-rockchip
Hi Robin,
Thank you for your review.
Added some questions in return.
This dts file seems to be some sort of variation of
rk3328-box-liantong.dtsi in the manufacturer tree. Depending on the
design the vendor then changes the wifi chip or removes the spdif
connector to save some cost.
On 8/3/20 11:41 PM, Robin Murphy wrote:
> On 2020-07-18 11:53, Johan Jonker wrote:
>> The rk3318 A95X Z2 boards are sold as TV box.
>> No further documentation is given, but from the dts files
>> extracted it seems that the rk3318 processor is simulair
>> to the rk3328. This dts file contains only the basic nodes
>> that have support in the mainline kernel.
>>
>> Features:
>>
>> CPU: RK3318 Quad-Core Cortex-A53
>> GPU: Mali-450
>> RAM: 2/4GB DDR3
>> ROM: EMMC 16/32/64GB
>> HDMI: HDMI 2.0a for 4k@60Hz
>> Ethernet: 10/100M standard RJ-45
>> WiFi: 2.4G+5G WIFI, 802.11 b/g/n
>> Bluetooth: 4.0
>> 1 x USB 3.0
>> 1 x USB 2.0
>> 1 x Micro SD card slot
>> 1 x SPDIF
>> 1 x AV
>> 1 x DC IN
>>
>> Signed-off-by: Johan Jonker <jbx6244@gmail.com>
>> ---
>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>> arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts | 393
>> ++++++++++++++++++++++++
>> 2 files changed, 394 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>> b/arch/arm64/boot/dts/rockchip/Makefile
>> index b87b1f773..aa508bc4a 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -2,6 +2,7 @@
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> new file mode 100644
>> index 000000000..413418ea1
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> @@ -0,0 +1,393 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/input/input.h>
>> +#include "rk3328.dtsi"
>> +
>> +/ {
>> + model = "A95X Z2";
>> + compatible = "zkmagic,a95x-z2", "rockchip,rk3318";
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + adc-keys {
>> + compatible = "adc-keys";
>> + io-channels = <&saradc 0>;
>> + io-channel-names = "buttons";
>> + keyup-threshold-microvolt = <1800000>;
>> + poll-interval = <100>;
>> +
>> + vol-up-key {
>> + label = "volume up";
>> + linux,code = <KEY_VOLUMEUP>;
>
> Really? If as usual this is actually the recovery button hidden inside
> the box, it's somewhat questionable whether it's worth describing in DT
> at all. At the very least it should probably be presented as something
> more realistic than half a volume control.
Dts use is not limited to a mainline kernel setting. In Android that
<KEY_VOLUMEUP> seem to be a standard way needed to enter a menu. Then
make it as complete as possible to make it work.
What would be your realistic key proposal?
>
>> + press-threshold-microvolt = <17000>;
>> + };
>> + };
>> +
>> + ir-receiver {
>> + compatible = "gpio-ir-receiver";
>> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&ir_int>;
>> + pinctrl-names = "default";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <&cyx_led_pin>;
>> + pinctrl-names = "default";
>> +
>> + cyx_led: led-0 {
>
> What needs a phandle to this node to warrant a label?
Without repeating previous discussions, I made a proposal that was
approved. So we just stick to that set of rules consequently.
A little explanation:
With the conversion to yaml a preferred nodename was introduced.
Legacy Rockchip node names were sort of free style and causing the
dts-checker to produce a flood of warnings.
The led properties are described in 2 places, under leds and under pinctrl.
To improve the readability given the legacy and to prevent the
disconnect between schematics, leds and pinctrl we add a label with a
consistent name.
Fix with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
>
>> + default-state = "on";
>> + gpios = <&gpio2 RK_PC7 GPIO_ACTIVE_LOW>;
>> + label = "CYX_LED";
This label with capital letters is used by an Android app, so keep it.
>> + };
>> + };
>> +
>> + sdio_pwrseq: sdio-pwrseq {
>> + compatible = "mmc-pwrseq-simple";
>> + pinctrl-0 = <&wifi_enable_h>;
>> + pinctrl-names = "default";
>> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + spdif-sound {
>> + compatible = "simple-audio-card";
>> + simple-audio-card,name = "spdif";
Some programs don't like long names here.
Recently I see others also use "SPDIF".
Should I change?
Currently for rk3328 we have: "Analog" and "HDMI"
Is there a standard?
Please advise.
>> +
>> + simple-audio-card,cpu {
>> + sound-dai = <&spdif>;
>> + };
>> +
>> + simple-audio-card,codec {
>> + sound-dai = <&spdif_out>;
>> + };
>> + };
>> +
>> + spdif_out: spdif-out {
>> + compatible = "linux,spdif-dit";
>> + #sound-dai-cells = <0>;
>> + };
>> +
>> + /* Power tree */
>> + regulators {
>
> Don't create fake "buses" for regulators, especially if they don't even
> contain most of the regulators anyway.
Agree.
The original reason was not given.
vccio_1v8_reg and vccio_3v3_reg are used mostly in &io_domains.
Is there a dependency requirement that both must be probed/enabled
before being used?
Without these regulators in a bus should we then add a vcc-sys-regulator
for a complete supply chain?
vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
>
>> + compatible = "simple-mfd";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + vccio_1v8_reg: regulator@0 {
>> + compatible = "regulator-fixed";
>> + reg = <0>;
>> + regulator-name = "vccio_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> +
>> + vccio_3v3_reg: regulator@1 {
>> + compatible = "regulator-fixed";
>> + reg = <1>;
>> + regulator-name = "vccio_3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> + };
>> +
>> + vcc_otg_vbus: otg-vbus-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
>> + pinctrl-0 = <&otg_vbus_drv>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + enable-active-high;
>> + };
>> +
>> + vcc_phy: vcc-phy-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc_phy";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>
> Is this actually a distinct regulator? The reference design has the
> internal FEPHY block powered pretty much directly from the general 1V8
> and 1V0 supplies that also power USB/HDMI/etc., so I'd rather expect
> low-end boxes to follow suit. Either way there doesn't seem to be a
> great deal of value in describing something with no controls, no voltage
> information, and no connection to the power tree.
Agree.
phy-supply appears to be an optional property, so removing it is
possible. It shows up in rk3328-roc-cc.dts and rk3328-evb.dts.
What does the maintainer prefer? Remove or not?
>
>> +
>> + vcc_sd: sdmmc-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&sdmmc0m1_gpio>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_sd";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + vin-supply = <&vccio_3v3_reg>;
>> + };
>> +
>> + vdd_arm: vdd-arm {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm0 0 5000 1>;
>> + regulator-name = "vdd_arm";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + vdd_log: vdd-log {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm1 0 5000 1>;
>> + regulator-name = "vdd_log";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +};
>> +
>> +&analog_sound {
>> + status = "okay";
>> +};
>> +
>> +&codec {
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu1 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu2 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu3 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu0_opp_table {
>> + opp-1200000000 {
>> + status = "disabled";
>> + };
>> +
>> + opp-1296000000 {
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&emmc {
>> + bus-width = <8>;
>> + cap-mmc-highspeed;
>> + non-removable;
>> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> +};
>> +
>> +&gmac2phy {
>> + assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
>> + assigned-clock-rate = <50000000>;
>> + assigned-clocks = <&cru SCLK_MAC2PHY>;
>> + clock_in_out = "output";
>> + phy-supply = <&vcc_phy>;
Remove or not?
>> + status = "okay";
>> +};
>> +
>> +&gpu {
>> + mali-supply = <&vdd_log>;
>> +};
>> +
>> +&hdmi {
>> + ddc-i2c-scl-high-time-ns = <9625>;
>> + ddc-i2c-scl-low-time-ns = <10000>;
>> + status = "okay";
>> +};
>> +
>> +&hdmiphy {
>> + status = "okay";
>> +};
>> +
>> +&hdmi_sound {
>> + status = "okay";
>> +};
>> +
>> +&i2s0 {
>> + status = "okay";
>> +};
>> +
>> +&i2s1 {
>> + status = "okay";
>> +};
>> +
>> +&io_domains {
>> + pmuio-supply = <&vccio_3v3_reg>;
>> + vccio1-supply = <&vccio_3v3_reg>;
>> + vccio2-supply = <&vccio_1v8_reg>;
>> + vccio3-supply = <&vccio_3v3_reg>;
>> + vccio4-supply = <&vccio_1v8_reg>;
>> + vccio5-supply = <&vccio_3v3_reg>;
>> + vccio6-supply = <&vccio_3v3_reg>;
>> + status = "okay";
>> +};
>> +
>> +&pinctrl {
>> + ir {
>> + ir_int: ir-int {
>> + rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + leds {
>> + cyx_led_pin: cyx-led-pin {
>> + rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + pwm0 {
>> + pwm0_pin_pull_up: pwm0-pin-pull-up {
>> + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + pwm1 {
>> + pwm1_pin_pull_up: pwm1-pin-pull-up {
>> + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + sdio-pwrseq {
>> + wifi_enable_h: wifi-enable-h {
>> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + sdmmc1 {
>> + clk_32k_out: clk-32k-out {
>> + rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + usb {
>> + host_vbus_drv: host-vbus-drv {
>> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> +
>> + otg_vbus_drv: otg-vbus-drv {
>> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +};
>> +
>> +&pwm0 {
>> + pinctrl-0 = <&pwm0_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&pwm1 {
>> + pinctrl-0 = <&pwm1_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&saradc {
>> + vref-supply = <&vccio_1v8_reg>;
>> + status = "okay";
>> +};
>> +
>> +&sdio {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + cap-sdio-irq;
>> + keep-power-in-suspend;
>> + max-frequency = <125000000>;
>> + mmc-pwrseq = <&sdio_pwrseq>;
>> + non-removable;
>> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &clk_32k_out>;
>> + pinctrl-names = "default";
>> + sd-uhs-sdr104;
>> + status = "okay";
>> +};
>> +
>> +&sdmmc {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + disable-wp;
This is from the manufacturer tree for a micro SD card. Remove or not?
Please advise.
>> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
>> + pinctrl-names = "default";
>> + vmmc-supply = <&vcc_sd>;
>> + status = "okay";
>> +};
>> +
>> +&spdif {
>> + pinctrl-0 = <&spdifm0_tx>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&soc_crit {
>> + temperature = <115000>; /* millicelsius */
>> +};
>> +
>> +&target {
>> + temperature = <105000>; /* millicelsius */
>> +};
>> +
>> +&threshold {
>> + temperature = <90000>; /* millicelsius */
>> +};
>> +
>> +&tsadc {
>> + rockchip,hw-tshut-temp = <120000>;
>> + status = "okay";
>> +};
>> +
>> +&u2phy {
>> + status = "okay";
>> +
>> + u2phy_host: host-port {
>
> Just refer to the ports normally by label rather than duplicate a random
> snippet of DTSI hierarchy - I'm not sure why this particular pattern
> seems to get copied around so much.
Here the node labels start with the same letters and the result will
stay together. In other cases it will scatter all over the dts file and
affects the readability. I just followed the manufacturer's example. If
the maintainer agrees then I'll change.
>
> Robin.
>
>> + status = "okay";
>> + };
>> +
>> + u2phy_otg: otg-port {
>> + phy-supply = <&vcc_otg_vbus>;
>> + status = "okay";
>> + };
>> +};
>> +
>> +&uart0 {
>> + pinctrl-0 = <&uart0_xfer &uart0_cts>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + status = "okay";
>> +};
>> +
>> +&usb20_otg {
>> + dr_mode = "host";
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ehci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ohci {
>> + status = "okay";
>> +};
>> +
>> +&vop {
>> + status = "okay";
>> +};
>> +
>> +&vop_mmu {
>> + status = "okay";
>> +};
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH v2 3/3] arm64: dts: rockchip: add rk3318 A95X Z2 board
@ 2020-08-04 15:54 ` Johan Jonker
0 siblings, 0 replies; 23+ messages in thread
From: Johan Jonker @ 2020-08-04 15:54 UTC (permalink / raw)
To: Robin Murphy, heiko-4mtYJXux2i+zQB+pC5nmwQ
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Robin,
Thank you for your review.
Added some questions in return.
This dts file seems to be some sort of variation of
rk3328-box-liantong.dtsi in the manufacturer tree. Depending on the
design the vendor then changes the wifi chip or removes the spdif
connector to save some cost.
On 8/3/20 11:41 PM, Robin Murphy wrote:
> On 2020-07-18 11:53, Johan Jonker wrote:
>> The rk3318 A95X Z2 boards are sold as TV box.
>> No further documentation is given, but from the dts files
>> extracted it seems that the rk3318 processor is simulair
>> to the rk3328. This dts file contains only the basic nodes
>> that have support in the mainline kernel.
>>
>> Features:
>>
>> CPU: RK3318 Quad-Core Cortex-A53
>> GPU: Mali-450
>> RAM: 2/4GB DDR3
>> ROM: EMMC 16/32/64GB
>> HDMI: HDMI 2.0a for 4k@60Hz
>> Ethernet: 10/100M standard RJ-45
>> WiFi: 2.4G+5G WIFI, 802.11 b/g/n
>> Bluetooth: 4.0
>> 1 x USB 3.0
>> 1 x USB 2.0
>> 1 x Micro SD card slot
>> 1 x SPDIF
>> 1 x AV
>> 1 x DC IN
>>
>> Signed-off-by: Johan Jonker <jbx6244-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>> arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts | 393
>> ++++++++++++++++++++++++
>> 2 files changed, 394 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>> b/arch/arm64/boot/dts/rockchip/Makefile
>> index b87b1f773..aa508bc4a 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -2,6 +2,7 @@
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> new file mode 100644
>> index 000000000..413418ea1
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
>> @@ -0,0 +1,393 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/input/input.h>
>> +#include "rk3328.dtsi"
>> +
>> +/ {
>> + model = "A95X Z2";
>> + compatible = "zkmagic,a95x-z2", "rockchip,rk3318";
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + adc-keys {
>> + compatible = "adc-keys";
>> + io-channels = <&saradc 0>;
>> + io-channel-names = "buttons";
>> + keyup-threshold-microvolt = <1800000>;
>> + poll-interval = <100>;
>> +
>> + vol-up-key {
>> + label = "volume up";
>> + linux,code = <KEY_VOLUMEUP>;
>
> Really? If as usual this is actually the recovery button hidden inside
> the box, it's somewhat questionable whether it's worth describing in DT
> at all. At the very least it should probably be presented as something
> more realistic than half a volume control.
Dts use is not limited to a mainline kernel setting. In Android that
<KEY_VOLUMEUP> seem to be a standard way needed to enter a menu. Then
make it as complete as possible to make it work.
What would be your realistic key proposal?
>
>> + press-threshold-microvolt = <17000>;
>> + };
>> + };
>> +
>> + ir-receiver {
>> + compatible = "gpio-ir-receiver";
>> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&ir_int>;
>> + pinctrl-names = "default";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <&cyx_led_pin>;
>> + pinctrl-names = "default";
>> +
>> + cyx_led: led-0 {
>
> What needs a phandle to this node to warrant a label?
Without repeating previous discussions, I made a proposal that was
approved. So we just stick to that set of rules consequently.
A little explanation:
With the conversion to yaml a preferred nodename was introduced.
Legacy Rockchip node names were sort of free style and causing the
dts-checker to produce a flood of warnings.
The led properties are described in 2 places, under leds and under pinctrl.
To improve the readability given the legacy and to prevent the
disconnect between schematics, leds and pinctrl we add a label with a
consistent name.
Fix with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
>
>> + default-state = "on";
>> + gpios = <&gpio2 RK_PC7 GPIO_ACTIVE_LOW>;
>> + label = "CYX_LED";
This label with capital letters is used by an Android app, so keep it.
>> + };
>> + };
>> +
>> + sdio_pwrseq: sdio-pwrseq {
>> + compatible = "mmc-pwrseq-simple";
>> + pinctrl-0 = <&wifi_enable_h>;
>> + pinctrl-names = "default";
>> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + spdif-sound {
>> + compatible = "simple-audio-card";
>> + simple-audio-card,name = "spdif";
Some programs don't like long names here.
Recently I see others also use "SPDIF".
Should I change?
Currently for rk3328 we have: "Analog" and "HDMI"
Is there a standard?
Please advise.
>> +
>> + simple-audio-card,cpu {
>> + sound-dai = <&spdif>;
>> + };
>> +
>> + simple-audio-card,codec {
>> + sound-dai = <&spdif_out>;
>> + };
>> + };
>> +
>> + spdif_out: spdif-out {
>> + compatible = "linux,spdif-dit";
>> + #sound-dai-cells = <0>;
>> + };
>> +
>> + /* Power tree */
>> + regulators {
>
> Don't create fake "buses" for regulators, especially if they don't even
> contain most of the regulators anyway.
Agree.
The original reason was not given.
vccio_1v8_reg and vccio_3v3_reg are used mostly in &io_domains.
Is there a dependency requirement that both must be probed/enabled
before being used?
Without these regulators in a bus should we then add a vcc-sys-regulator
for a complete supply chain?
vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
>
>> + compatible = "simple-mfd";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + vccio_1v8_reg: regulator@0 {
>> + compatible = "regulator-fixed";
>> + reg = <0>;
>> + regulator-name = "vccio_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> +
>> + vccio_3v3_reg: regulator@1 {
>> + compatible = "regulator-fixed";
>> + reg = <1>;
>> + regulator-name = "vccio_3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
Just an example:
vin-supply = <&vcc_sys>;
>> + };
>> + };
>> +
>> + vcc_otg_vbus: otg-vbus-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
>> + pinctrl-0 = <&otg_vbus_drv>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + enable-active-high;
>> + };
>> +
>> + vcc_phy: vcc-phy-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc_phy";
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>
> Is this actually a distinct regulator? The reference design has the
> internal FEPHY block powered pretty much directly from the general 1V8
> and 1V0 supplies that also power USB/HDMI/etc., so I'd rather expect
> low-end boxes to follow suit. Either way there doesn't seem to be a
> great deal of value in describing something with no controls, no voltage
> information, and no connection to the power tree.
Agree.
phy-supply appears to be an optional property, so removing it is
possible. It shows up in rk3328-roc-cc.dts and rk3328-evb.dts.
What does the maintainer prefer? Remove or not?
>
>> +
>> + vcc_sd: sdmmc-regulator {
>> + compatible = "regulator-fixed";
>> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&sdmmc0m1_gpio>;
>> + pinctrl-names = "default";
>> + regulator-name = "vcc_sd";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + vin-supply = <&vccio_3v3_reg>;
>> + };
>> +
>> + vdd_arm: vdd-arm {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm0 0 5000 1>;
>> + regulator-name = "vdd_arm";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +
>> + vdd_log: vdd-log {
>> + compatible = "pwm-regulator";
>> + pwms = <&pwm1 0 5000 1>;
>> + regulator-name = "vdd_log";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-settling-time-up-us = <250>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + };
>> +};
>> +
>> +&analog_sound {
>> + status = "okay";
>> +};
>> +
>> +&codec {
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu1 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu2 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu3 {
>> + cpu-supply = <&vdd_arm>;
>> +};
>> +
>> +&cpu0_opp_table {
>> + opp-1200000000 {
>> + status = "disabled";
>> + };
>> +
>> + opp-1296000000 {
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&emmc {
>> + bus-width = <8>;
>> + cap-mmc-highspeed;
>> + non-removable;
>> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> +};
>> +
>> +&gmac2phy {
>> + assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
>> + assigned-clock-rate = <50000000>;
>> + assigned-clocks = <&cru SCLK_MAC2PHY>;
>> + clock_in_out = "output";
>> + phy-supply = <&vcc_phy>;
Remove or not?
>> + status = "okay";
>> +};
>> +
>> +&gpu {
>> + mali-supply = <&vdd_log>;
>> +};
>> +
>> +&hdmi {
>> + ddc-i2c-scl-high-time-ns = <9625>;
>> + ddc-i2c-scl-low-time-ns = <10000>;
>> + status = "okay";
>> +};
>> +
>> +&hdmiphy {
>> + status = "okay";
>> +};
>> +
>> +&hdmi_sound {
>> + status = "okay";
>> +};
>> +
>> +&i2s0 {
>> + status = "okay";
>> +};
>> +
>> +&i2s1 {
>> + status = "okay";
>> +};
>> +
>> +&io_domains {
>> + pmuio-supply = <&vccio_3v3_reg>;
>> + vccio1-supply = <&vccio_3v3_reg>;
>> + vccio2-supply = <&vccio_1v8_reg>;
>> + vccio3-supply = <&vccio_3v3_reg>;
>> + vccio4-supply = <&vccio_1v8_reg>;
>> + vccio5-supply = <&vccio_3v3_reg>;
>> + vccio6-supply = <&vccio_3v3_reg>;
>> + status = "okay";
>> +};
>> +
>> +&pinctrl {
>> + ir {
>> + ir_int: ir-int {
>> + rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + leds {
>> + cyx_led_pin: cyx-led-pin {
>> + rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + pwm0 {
>> + pwm0_pin_pull_up: pwm0-pin-pull-up {
>> + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + pwm1 {
>> + pwm1_pin_pull_up: pwm1-pin-pull-up {
>> + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_up>;
>> + };
>> + };
>> +
>> + sdio-pwrseq {
>> + wifi_enable_h: wifi-enable-h {
>> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + sdmmc1 {
>> + clk_32k_out: clk-32k-out {
>> + rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
>> + };
>> + };
>> +
>> + usb {
>> + host_vbus_drv: host-vbus-drv {
>> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> +
>> + otg_vbus_drv: otg-vbus-drv {
>> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
>> + };
>> + };
>> +};
>> +
>> +&pwm0 {
>> + pinctrl-0 = <&pwm0_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&pwm1 {
>> + pinctrl-0 = <&pwm1_pin_pull_up>;
>> + pinctrl-names = "active";
>> + status = "okay";
>> +};
>> +
>> +&saradc {
>> + vref-supply = <&vccio_1v8_reg>;
>> + status = "okay";
>> +};
>> +
>> +&sdio {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + cap-sdio-irq;
>> + keep-power-in-suspend;
>> + max-frequency = <125000000>;
>> + mmc-pwrseq = <&sdio_pwrseq>;
>> + non-removable;
>> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &clk_32k_out>;
>> + pinctrl-names = "default";
>> + sd-uhs-sdr104;
>> + status = "okay";
>> +};
>> +
>> +&sdmmc {
>> + bus-width = <4>;
>> + cap-sd-highspeed;
>> + disable-wp;
This is from the manufacturer tree for a micro SD card. Remove or not?
Please advise.
>> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
>> + pinctrl-names = "default";
>> + vmmc-supply = <&vcc_sd>;
>> + status = "okay";
>> +};
>> +
>> +&spdif {
>> + pinctrl-0 = <&spdifm0_tx>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&soc_crit {
>> + temperature = <115000>; /* millicelsius */
>> +};
>> +
>> +&target {
>> + temperature = <105000>; /* millicelsius */
>> +};
>> +
>> +&threshold {
>> + temperature = <90000>; /* millicelsius */
>> +};
>> +
>> +&tsadc {
>> + rockchip,hw-tshut-temp = <120000>;
>> + status = "okay";
>> +};
>> +
>> +&u2phy {
>> + status = "okay";
>> +
>> + u2phy_host: host-port {
>
> Just refer to the ports normally by label rather than duplicate a random
> snippet of DTSI hierarchy - I'm not sure why this particular pattern
> seems to get copied around so much.
Here the node labels start with the same letters and the result will
stay together. In other cases it will scatter all over the dts file and
affects the readability. I just followed the manufacturer's example. If
the maintainer agrees then I'll change.
>
> Robin.
>
>> + status = "okay";
>> + };
>> +
>> + u2phy_otg: otg-port {
>> + phy-supply = <&vcc_otg_vbus>;
>> + status = "okay";
>> + };
>> +};
>> +
>> +&uart0 {
>> + pinctrl-0 = <&uart0_xfer &uart0_cts>;
>> + pinctrl-names = "default";
Remove.
Already in dtsi.
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + status = "okay";
>> +};
>> +
>> +&usb20_otg {
>> + dr_mode = "host";
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ehci {
>> + status = "okay";
>> +};
>> +
>> +&usb_host0_ohci {
>> + status = "okay";
>> +};
>> +
>> +&vop {
>> + status = "okay";
>> +};
>> +
>> +&vop_mmu {
>> + status = "okay";
>> +};
>>
^ permalink raw reply [flat|nested] 23+ messages in thread