[PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Dan Murphy]

Hello

These are the final patches from the original multicolor framework patchset.

Changes made were to the LP50xx to rework regmap_defaults to eliminate used
only once #defines.  Also fixed putting the child node in the dt parsing and
changed regmap regcache type to flat.

Dan

Dan Murphy (6):
  dt: bindings: lp50xx: Introduce the lp50xx family of RGB drivers
  leds: lp50xx: Add the LP50XX family of the RGB LED driver
  ARM: defconfig: u8500: Add LP55XX_COMMON config flag
  ARM: dts: n900: Add reg property to the LP5523 channel node
  ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node
  ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

 .../devicetree/bindings/leds/leds-lp50xx.yaml | 130 ++++
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi    |  14 +-
 arch/arm/boot/dts/omap3-n900.dts              |  29 +-
 arch/arm/boot/dts/ste-href.dtsi               |  22 +-
 arch/arm/configs/u8500_defconfig              |   1 +
 drivers/leds/Kconfig                          |  11 +
 drivers/leds/Makefile                         |   1 +
 drivers/leds/leds-lp50xx.c                    | 634 ++++++++++++++++++
 8 files changed, 823 insertions(+), 19 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
 create mode 100644 drivers/leds/leds-lp50xx.c

-- 
2.28.0

[PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Dan Murphy]

Hello

These are the final patches from the original multicolor framework patchset.

Changes made were to the LP50xx to rework regmap_defaults to eliminate used
only once #defines.  Also fixed putting the child node in the dt parsing and
changed regmap regcache type to flat.

Dan

Dan Murphy (6):
  dt: bindings: lp50xx: Introduce the lp50xx family of RGB drivers
  leds: lp50xx: Add the LP50XX family of the RGB LED driver
  ARM: defconfig: u8500: Add LP55XX_COMMON config flag
  ARM: dts: n900: Add reg property to the LP5523 channel node
  ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node
  ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

 .../devicetree/bindings/leds/leds-lp50xx.yaml | 130 ++++
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi    |  14 +-
 arch/arm/boot/dts/omap3-n900.dts              |  29 +-
 arch/arm/boot/dts/ste-href.dtsi               |  22 +-
 arch/arm/configs/u8500_defconfig              |   1 +
 drivers/leds/Kconfig                          |  11 +
 drivers/leds/Makefile                         |   1 +
 drivers/leds/leds-lp50xx.c                    | 634 ++++++++++++++++++
 8 files changed, 823 insertions(+), 19 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
 create mode 100644 drivers/leds/leds-lp50xx.c

-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 1/6] dt: bindings: lp50xx: Introduce the lp50xx family of RGB drivers

[Dan Murphy]

Introduce the bindings for the Texas Instruments LP5036, LP5030, LP5024,
LP5018, LP5012 and LP5009 RGB LED device driver.  The LP5036/30/24/18/12/9
can control RGB LEDs individually or as part of a control bank group.
These devices have the ability to adjust the mixing control for the RGB
LEDs to obtain different colors independent of the overall brightness of
the LED grouping.

Datasheet:
http://www.ti.com/lit/ds/symlink/lp5012.pdf
http://www.ti.com/lit/ds/symlink/lp5024.pdf
http://www.ti.com/lit/ds/symlink/lp5036.pdf

Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 .../devicetree/bindings/leds/leds-lp50xx.yaml | 130 ++++++++++++++++++
 1 file changed, 130 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-lp50xx.yaml

diff --git a/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
new file mode 100644
index 000000000000..947542a253ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-lp50xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LED driver for LP50XX RGB LED from Texas Instruments.
+
+maintainers:
+  - Dan Murphy <dmurphy@ti.com>
+
+description: |
+  The LP50XX is multi-channel, I2C RGB LED Drivers that can group RGB LEDs into
+  a LED group or control them individually.
+
+  The difference in these RGB LED drivers is the number of supported RGB
+  modules.
+
+  For more product information please see the link below:
+  https://www.ti.com/lit/ds/symlink/lp5012.pdf
+  https://www.ti.com/lit/ds/symlink/lp5024.pdf
+  https://www.ti.com/lit/ds/symlink/lp5036.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,lp5009
+      - ti,lp5012
+      - ti,lp5018
+      - ti,lp5024
+      - ti,lp5030
+      - ti,lp5036
+
+  reg:
+    maxItems: 1
+    description:
+      I2C slave address
+      lp5009/12 - 0x14, 0x15, 0x16, 0x17
+      lp5018/24 - 0x28, 0x29, 0x2a, 0x2b
+      lp5030/36 - 0x30, 0x31, 0x32, 0x33
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO pin to enable/disable the device.
+
+  vled-supply:
+    description: LED supply.
+
+patternProperties:
+  '^multi-led@[0-9a-f]$':
+    type: object
+    allOf:
+      - $ref: leds-class-multicolor.yaml#
+    properties:
+      reg:
+        minItems: 1
+        maxItems: 12
+        description:
+          This property denotes the LED module number(s) that is used on the
+          for the child node.  The LED modules can either be used stand alone
+          or grouped into a module bank.
+
+    patternProperties:
+      "(^led-[0-9a-f]$|led)":
+        type: object
+        $ref: common.yaml#
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+   #include <dt-bindings/gpio/gpio.h>
+   #include <dt-bindings/leds/common.h>
+
+   i2c {
+       #address-cells = <1>;
+       #size-cells = <0>;
+
+       led-controller@14 {
+           compatible = "ti,lp5009";
+           reg = <0x14>;
+           #address-cells = <1>;
+           #size-cells = <0>;
+           enable-gpios = <&gpio1 16>;
+
+           multi-led@1 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x1>;
+               color = <LED_COLOR_ID_RGB>;
+               function = LED_FUNCTION_CHARGING;
+
+               led-0 {
+                   color = <LED_COLOR_ID_RED>;
+               };
+
+               led-1 {
+                   color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-2 {
+                   color = <LED_COLOR_ID_BLUE>;
+               };
+          };
+
+          multi-led@2 {
+            #address-cells = <1>;
+            #size-cells = <2>;
+            reg = <0x2 0x3 0x5>;
+            color = <LED_COLOR_ID_RGB>;
+            function = LED_FUNCTION_STANDBY;
+
+            led-6 {
+              color = <LED_COLOR_ID_RED>;
+            };
+
+            led-7 {
+              color = <LED_COLOR_ID_GREEN>;
+            };
+
+            led-8 {
+              color = <LED_COLOR_ID_BLUE>;
+            };
+         };
+       };
+    };
+
+...
-- 
2.28.0

[PATCH v33 1/6] dt: bindings: lp50xx: Introduce the lp50xx family of RGB drivers

[Dan Murphy]

Introduce the bindings for the Texas Instruments LP5036, LP5030, LP5024,
LP5018, LP5012 and LP5009 RGB LED device driver.  The LP5036/30/24/18/12/9
can control RGB LEDs individually or as part of a control bank group.
These devices have the ability to adjust the mixing control for the RGB
LEDs to obtain different colors independent of the overall brightness of
the LED grouping.

Datasheet:
http://www.ti.com/lit/ds/symlink/lp5012.pdf
http://www.ti.com/lit/ds/symlink/lp5024.pdf
http://www.ti.com/lit/ds/symlink/lp5036.pdf

Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 .../devicetree/bindings/leds/leds-lp50xx.yaml | 130 ++++++++++++++++++
 1 file changed, 130 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-lp50xx.yaml

diff --git a/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
new file mode 100644
index 000000000000..947542a253ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-lp50xx.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-lp50xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LED driver for LP50XX RGB LED from Texas Instruments.
+
+maintainers:
+  - Dan Murphy <dmurphy@ti.com>
+
+description: |
+  The LP50XX is multi-channel, I2C RGB LED Drivers that can group RGB LEDs into
+  a LED group or control them individually.
+
+  The difference in these RGB LED drivers is the number of supported RGB
+  modules.
+
+  For more product information please see the link below:
+  https://www.ti.com/lit/ds/symlink/lp5012.pdf
+  https://www.ti.com/lit/ds/symlink/lp5024.pdf
+  https://www.ti.com/lit/ds/symlink/lp5036.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,lp5009
+      - ti,lp5012
+      - ti,lp5018
+      - ti,lp5024
+      - ti,lp5030
+      - ti,lp5036
+
+  reg:
+    maxItems: 1
+    description:
+      I2C slave address
+      lp5009/12 - 0x14, 0x15, 0x16, 0x17
+      lp5018/24 - 0x28, 0x29, 0x2a, 0x2b
+      lp5030/36 - 0x30, 0x31, 0x32, 0x33
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO pin to enable/disable the device.
+
+  vled-supply:
+    description: LED supply.
+
+patternProperties:
+  '^multi-led@[0-9a-f]$':
+    type: object
+    allOf:
+      - $ref: leds-class-multicolor.yaml#
+    properties:
+      reg:
+        minItems: 1
+        maxItems: 12
+        description:
+          This property denotes the LED module number(s) that is used on the
+          for the child node.  The LED modules can either be used stand alone
+          or grouped into a module bank.
+
+    patternProperties:
+      "(^led-[0-9a-f]$|led)":
+        type: object
+        $ref: common.yaml#
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+   #include <dt-bindings/gpio/gpio.h>
+   #include <dt-bindings/leds/common.h>
+
+   i2c {
+       #address-cells = <1>;
+       #size-cells = <0>;
+
+       led-controller@14 {
+           compatible = "ti,lp5009";
+           reg = <0x14>;
+           #address-cells = <1>;
+           #size-cells = <0>;
+           enable-gpios = <&gpio1 16>;
+
+           multi-led@1 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x1>;
+               color = <LED_COLOR_ID_RGB>;
+               function = LED_FUNCTION_CHARGING;
+
+               led-0 {
+                   color = <LED_COLOR_ID_RED>;
+               };
+
+               led-1 {
+                   color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-2 {
+                   color = <LED_COLOR_ID_BLUE>;
+               };
+          };
+
+          multi-led@2 {
+            #address-cells = <1>;
+            #size-cells = <2>;
+            reg = <0x2 0x3 0x5>;
+            color = <LED_COLOR_ID_RGB>;
+            function = LED_FUNCTION_STANDBY;
+
+            led-6 {
+              color = <LED_COLOR_ID_RED>;
+            };
+
+            led-7 {
+              color = <LED_COLOR_ID_GREEN>;
+            };
+
+            led-8 {
+              color = <LED_COLOR_ID_BLUE>;
+            };
+         };
+       };
+    };
+
+...
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 2/6] leds: lp50xx: Add the LP50XX family of the RGB LED driver

[Dan Murphy]

Introduce the LP5036/30/24/18/12/9 RGB LED driver.
The difference in these parts are the number of
LED outputs where the:

LP5036 can control 36 LEDs
LP5030 can control 30 LEDs
LP5024 can control 24 LEDs
LP5018 can control 18 LEDs
LP5012 can control 12 LEDs
LP5009 can control 9 LEDs

The device has the ability to group LED outputs into control banks
so that multiple LED banks can be controlled with the same mixing and
brightness. Or the LED outputs can also be controlled independently.

Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 drivers/leds/Kconfig       |  11 +
 drivers/leds/Makefile      |   1 +
 drivers/leds/leds-lp50xx.c | 634 +++++++++++++++++++++++++++++++++++++
 3 files changed, 646 insertions(+)
 create mode 100644 drivers/leds/leds-lp50xx.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 1c181df24eae..00b488915945 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -395,6 +395,17 @@ config LEDS_LP3952
 	  To compile this driver as a module, choose M here: the
 	  module will be called leds-lp3952.
 
+config LEDS_LP50XX
+	tristate "LED Support for TI LP5036/30/24/18/12/9 LED driver chip"
+	depends on LEDS_CLASS && REGMAP_I2C
+	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
+	help
+	  If you say yes here you get support for the Texas Instruments
+	  LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called leds-lp50xx.
+
 config LEDS_LP55XX_COMMON
 	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index c2c7d7ade0d0..778cb4bb8c52 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_LEDS_LM3697)		+= leds-lm3697.o
 obj-$(CONFIG_LEDS_LOCOMO)		+= leds-locomo.o
 obj-$(CONFIG_LEDS_LP3944)		+= leds-lp3944.o
 obj-$(CONFIG_LEDS_LP3952)		+= leds-lp3952.o
+obj-$(CONFIG_LEDS_LP50XX)		+= leds-lp50xx.o
 obj-$(CONFIG_LEDS_LP5521)		+= leds-lp5521.o
 obj-$(CONFIG_LEDS_LP5523)		+= leds-lp5523.o
 obj-$(CONFIG_LEDS_LP5562)		+= leds-lp5562.o
diff --git a/drivers/leds/leds-lp50xx.c b/drivers/leds/leds-lp50xx.c
new file mode 100644
index 000000000000..47144a37cb94
--- /dev/null
+++ b/drivers/leds/leds-lp50xx.c
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LP50XX LED chip family driver
+// Copyright (C) 2018-20 Texas Instruments Incorporated - https://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#include <linux/led-class-multicolor.h>
+
+#include "leds.h"
+
+#define LP50XX_DEV_CFG0		0x00
+#define LP50XX_DEV_CFG1		0x01
+#define LP50XX_LED_CFG0		0x02
+
+/* LP5009 and LP5012 registers */
+#define LP5012_BNK_BRT		0x03
+#define LP5012_BNKA_CLR		0x04
+#define LP5012_BNKB_CLR		0x05
+#define LP5012_BNKC_CLR		0x06
+#define LP5012_LED0_BRT		0x07
+#define LP5012_OUT0_CLR		0x0b
+#define LP5012_RESET		0x17
+
+/* LP5018 and LP5024 registers */
+#define LP5024_BNK_BRT		0x03
+#define LP5024_BNKA_CLR		0x04
+#define LP5024_BNKB_CLR		0x05
+#define LP5024_BNKC_CLR		0x06
+#define LP5024_LED0_BRT		0x07
+#define LP5024_OUT0_CLR		0x0f
+#define LP5024_RESET		0x27
+
+/* LP5030 and LP5036 registers */
+#define LP5036_LED_CFG1		0x03
+#define LP5036_BNK_BRT		0x04
+#define LP5036_BNKA_CLR		0x05
+#define LP5036_BNKB_CLR		0x06
+#define LP5036_BNKC_CLR		0x07
+#define LP5036_LED0_BRT		0x08
+#define LP5036_OUT0_CLR		0x14
+#define LP5036_RESET		0x38
+
+#define LP50XX_SW_RESET		0xff
+#define LP50XX_CHIP_EN		BIT(6)
+
+/* There are 3 LED outputs per bank */
+#define LP50XX_LEDS_PER_MODULE	3
+
+#define LP5009_MAX_LED_MODULES	2
+#define LP5012_MAX_LED_MODULES	4
+#define LP5018_MAX_LED_MODULES	6
+#define LP5024_MAX_LED_MODULES	8
+#define LP5030_MAX_LED_MODULES	10
+#define LP5036_MAX_LED_MODULES	12
+
+static const struct reg_default lp5012_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5012_BNK_BRT, 0xff},
+	{LP5012_BNKA_CLR, 0x0f},
+	{LP5012_BNKB_CLR, 0x0f},
+	{LP5012_BNKC_CLR, 0x0f},
+	{LP5012_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff},
+	{LP5012_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x0c, 0x00}, {0x0d, 0x00}, {0x0e, 0x00}, {0x0f, 0x00}, {0x10, 0x00},
+	{0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00},	{0x15, 0x00},
+	{0x16, 0x00},
+	{LP5012_RESET, 0x00}
+};
+
+static const struct reg_default lp5024_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5024_BNK_BRT, 0xff},
+	{LP5024_BNKA_CLR, 0x0f},
+	{LP5024_BNKB_CLR, 0x0f},
+	{LP5024_BNKC_CLR, 0x0f},
+	{LP5024_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+	{0x0d, 0xff}, {0x0e, 0xff},
+	{LP5024_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x10, 0x00}, {0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00},
+	{0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+	{0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+	{0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+	{0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00},
+	{LP5024_RESET, 0x00}
+};
+
+static const struct reg_default lp5036_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5036_LED_CFG1, 0x0},
+	{LP5036_BNK_BRT, 0xff},
+	{LP5036_BNKA_CLR, 0x0f},
+	{LP5036_BNKB_CLR, 0x0f},
+	{LP5036_BNKC_CLR, 0x0f},
+	{LP5036_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+	{0x0d, 0xff}, {0x0e, 0xff}, {0x0f, 0xff}, {0x10, 0xff}, {0x11, 0xff},
+	{0x12, 0xff}, {0x13, 0xff},
+	{LP5036_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+	{0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+	{0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+	{0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
+	{0x29, 0x00}, {0x2a, 0x00}, {0x2b, 0x00}, {0x2c, 0x00}, {0x2d, 0x00},
+	{0x2e, 0x00}, {0x2f, 0x00}, {0x30, 0x00}, {0x31, 0x00}, {0x32, 0x00},
+	{0x33, 0x00}, {0x34, 0x00}, {0x35, 0x00}, {0x36, 0x00}, {0x37, 0x00},
+	{LP5036_RESET, 0x00}
+};
+
+static const struct regmap_config lp5012_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5012_RESET,
+	.reg_defaults = lp5012_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5012_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5024_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5024_RESET,
+	.reg_defaults = lp5024_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5024_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5036_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5036_RESET,
+	.reg_defaults = lp5036_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5036_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+enum lp50xx_model {
+	LP5009,
+	LP5012,
+	LP5018,
+	LP5024,
+	LP5030,
+	LP5036,
+};
+
+/**
+ * struct lp50xx_chip_info -
+ * @lp50xx_regmap_config: regmap register configuration
+ * @model_id: LED device model
+ * @max_modules: total number of supported LED modules
+ * @num_leds: number of LED outputs available on the device
+ * @led_brightness0_reg: first brightness register of the device
+ * @mix_out0_reg: first color mix register of the device
+ * @bank_brt_reg: bank brightness register
+ * @bank_mix_reg: color mix register
+ * @reset_reg: device reset register
+ */
+struct lp50xx_chip_info {
+	const struct regmap_config *lp50xx_regmap_config;
+	int model_id;
+	u8 max_modules;
+	u8 num_leds;
+	u8 led_brightness0_reg;
+	u8 mix_out0_reg;
+	u8 bank_brt_reg;
+	u8 bank_mix_reg;
+	u8 reset_reg;
+};
+
+static const struct lp50xx_chip_info lp50xx_chip_info_tbl[] = {
+	[LP5009] = {
+		.model_id = LP5009,
+		.max_modules = LP5009_MAX_LED_MODULES,
+		.num_leds = LP5009_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = &lp5012_regmap_config,
+	},
+	[LP5012] = {
+		.model_id = LP5012,
+		.max_modules = LP5012_MAX_LED_MODULES,
+		.num_leds = LP5012_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = &lp5012_regmap_config,
+	},
+	[LP5018] = {
+		.model_id = LP5018,
+		.max_modules = LP5018_MAX_LED_MODULES,
+		.num_leds = LP5018_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = &lp5024_regmap_config,
+	},
+	[LP5024] = {
+		.model_id = LP5024,
+		.max_modules = LP5024_MAX_LED_MODULES,
+		.num_leds = LP5024_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = &lp5024_regmap_config,
+	},
+	[LP5030] = {
+		.model_id = LP5030,
+		.max_modules = LP5030_MAX_LED_MODULES,
+		.num_leds = LP5030_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = &lp5036_regmap_config,
+	},
+	[LP5036] = {
+		.model_id = LP5036,
+		.max_modules = LP5036_MAX_LED_MODULES,
+		.num_leds = LP5036_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = &lp5036_regmap_config,
+	},
+};
+
+struct lp50xx_led {
+	struct led_classdev_mc mc_cdev;
+	struct lp50xx *priv;
+	unsigned long bank_modules;
+	int led_intensity[LP50XX_LEDS_PER_MODULE];
+	u8 ctrl_bank_enabled;
+	int led_number;
+};
+
+/**
+ * struct lp50xx -
+ * @enable_gpio: hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: pointer to the I2C client
+ * @regmap: device register map
+ * @dev: pointer to the devices device struct
+ * @lock: lock for reading/writing the device
+ * @chip_info: chip specific information (ie num_leds)
+ * @num_of_banked_leds: holds the number of banked LEDs
+ * @leds: array of LED strings
+ */
+struct lp50xx {
+	struct gpio_desc *enable_gpio;
+	struct regulator *regulator;
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct device *dev;
+	struct mutex lock;
+	const struct lp50xx_chip_info *chip_info;
+	int num_of_banked_leds;
+
+	/* This needs to be at the end of the struct */
+	struct lp50xx_led leds[];
+};
+
+static struct lp50xx_led *mcled_cdev_to_led(struct led_classdev_mc *mc_cdev)
+{
+	return container_of(mc_cdev, struct lp50xx_led, mc_cdev);
+}
+
+static int lp50xx_brightness_set(struct led_classdev *cdev,
+			     enum led_brightness brightness)
+{
+	struct led_classdev_mc *mc_dev = lcdev_to_mccdev(cdev);
+	struct lp50xx_led *led = mcled_cdev_to_led(mc_dev);
+	const struct lp50xx_chip_info *led_chip = led->priv->chip_info;
+	u8 led_offset, reg_val;
+	int ret = 0;
+	int i;
+
+	mutex_lock(&led->priv->lock);
+	if (led->ctrl_bank_enabled)
+		reg_val = led_chip->bank_brt_reg;
+	else
+		reg_val = led_chip->led_brightness0_reg +
+			  led->led_number;
+
+	ret = regmap_write(led->priv->regmap, reg_val, brightness);
+	if (ret) {
+		dev_err(&led->priv->client->dev,
+			"Cannot write brightness value %d\n", ret);
+		goto out;
+	}
+
+	for (i = 0; i < led->mc_cdev.num_colors; i++) {
+		if (led->ctrl_bank_enabled) {
+			reg_val = led_chip->bank_mix_reg + i;
+		} else {
+			led_offset = (led->led_number * 3) + i;
+			reg_val = led_chip->mix_out0_reg + led_offset;
+		}
+
+		ret = regmap_write(led->priv->regmap, reg_val,
+				   mc_dev->subled_info[i].intensity);
+		if (ret) {
+			dev_err(&led->priv->client->dev,
+				"Cannot write intensity value %d\n", ret);
+			goto out;
+		}
+	}
+out:
+	mutex_unlock(&led->priv->lock);
+	return ret;
+}
+
+static int lp50xx_set_banks(struct lp50xx *priv, u32 led_banks[])
+{
+	u8 led_config_lo, led_config_hi;
+	u32 bank_enable_mask = 0;
+	int ret;
+	int i;
+
+	for (i = 0; i < priv->chip_info->max_modules; i++) {
+		if (led_banks[i])
+			bank_enable_mask |= (1 << led_banks[i]);
+	}
+
+	led_config_lo = (u8)(bank_enable_mask & 0xff);
+	led_config_hi = (u8)(bank_enable_mask >> 8) & 0xff;
+
+	ret = regmap_write(priv->regmap, LP50XX_LED_CFG0, led_config_lo);
+	if (ret)
+		return ret;
+
+	if (priv->chip_info->model_id >= LP5030)
+		ret = regmap_write(priv->regmap, LP5036_LED_CFG1, led_config_hi);
+
+	return ret;
+}
+
+static int lp50xx_reset(struct lp50xx *priv)
+{
+	return regmap_write(priv->regmap, priv->chip_info->reset_reg, LP50XX_SW_RESET);
+}
+
+static int lp50xx_enable_disable(struct lp50xx *priv, int enable_disable)
+{
+	int ret;
+
+	if (priv->enable_gpio) {
+		ret = gpiod_direction_output(priv->enable_gpio, enable_disable);
+		if (ret)
+			return ret;
+	}
+
+	if (enable_disable)
+		return regmap_write(priv->regmap, LP50XX_DEV_CFG0, LP50XX_CHIP_EN);
+	else
+		return regmap_write(priv->regmap, LP50XX_DEV_CFG0, 0);
+
+}
+
+static int lp50xx_probe_leds(struct fwnode_handle *child, struct lp50xx *priv,
+			     struct lp50xx_led *led, int num_leds)
+{
+	u32 led_banks[LP5036_MAX_LED_MODULES] = {0};
+	int led_number;
+	int ret;
+
+	if (num_leds > 1) {
+		if (num_leds > priv->chip_info->max_modules) {
+			dev_err(&priv->client->dev, "reg property is invalid\n");
+			return -EINVAL;
+		}
+
+		priv->num_of_banked_leds = num_leds;
+
+		ret = fwnode_property_read_u32_array(child, "reg", led_banks, num_leds);
+		if (ret) {
+			dev_err(&priv->client->dev, "reg property is missing\n");
+			return ret;
+		}
+
+		ret = lp50xx_set_banks(priv, led_banks);
+		if (ret) {
+			dev_err(&priv->client->dev, "Cannot setup banked LEDs\n");
+			return ret;
+		}
+
+		led->ctrl_bank_enabled = 1;
+	} else {
+		ret = fwnode_property_read_u32(child, "reg", &led_number);
+		if (ret) {
+			dev_err(&priv->client->dev, "led reg property missing\n");
+			return ret;
+		}
+
+		if (led_number > priv->chip_info->num_leds) {
+			dev_err(&priv->client->dev, "led-sources property is invalid\n");
+			return -EINVAL;
+		}
+
+		led->led_number = led_number;
+	}
+
+	return 0;
+}
+
+static int lp50xx_probe_dt(struct lp50xx *priv)
+{
+	struct fwnode_handle *child = NULL;
+	struct fwnode_handle *led_node = NULL;
+	struct led_init_data init_data = {};
+	struct led_classdev *led_cdev;
+	struct mc_subled *mc_led_info;
+	struct lp50xx_led *led;
+	int ret = -EINVAL;
+	int num_colors;
+	u32 color_id;
+	int i = 0;
+
+	priv->enable_gpio = devm_gpiod_get_optional(priv->dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->enable_gpio)) {
+		ret = PTR_ERR(priv->enable_gpio);
+		dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+			ret);
+		return ret;
+	}
+
+	priv->regulator = devm_regulator_get(priv->dev, "vled");
+	if (IS_ERR(priv->regulator))
+		priv->regulator = NULL;
+
+	device_for_each_child_node(priv->dev, child) {
+		led = &priv->leds[i];
+		ret = fwnode_property_count_u32(child, "reg");
+		if (ret < 0) {
+			dev_err(&priv->client->dev, "reg property is invalid\n");
+			goto child_out;
+		}
+
+		ret = lp50xx_probe_leds(child, priv, led, ret);
+		if (ret)
+			goto child_out;
+
+		init_data.fwnode = child;
+		num_colors = 0;
+
+		/*
+		 * There are only 3 LEDs per module otherwise they should be
+		 * banked which also is presented as 3 LEDs.
+		 */
+		mc_led_info = devm_kcalloc(priv->dev, LP50XX_LEDS_PER_MODULE,
+					   sizeof(*mc_led_info), GFP_KERNEL);
+		if (!mc_led_info)
+			return -ENOMEM;
+
+		fwnode_for_each_child_node(child, led_node) {
+			ret = fwnode_property_read_u32(led_node, "color",
+						       &color_id);
+			if (ret) {
+				dev_err(priv->dev, "Cannot read color\n");
+				goto child_out;
+			}
+
+			mc_led_info[num_colors].color_index = color_id;
+			num_colors++;
+		}
+
+		led->priv = priv;
+		led->mc_cdev.num_colors = num_colors;
+		led->mc_cdev.subled_info = mc_led_info;
+		led_cdev = &led->mc_cdev.led_cdev;
+		led_cdev->brightness_set_blocking = lp50xx_brightness_set;
+
+		fwnode_property_read_string(child, "linux,default-trigger",
+					    &led_cdev->default_trigger);
+
+		ret = devm_led_classdev_multicolor_register_ext(&priv->client->dev,
+						       &led->mc_cdev,
+						       &init_data);
+		if (ret) {
+			dev_err(&priv->client->dev, "led register err: %d\n",
+				ret);
+			goto child_out;
+		}
+		i++;
+		fwnode_handle_put(child);
+	}
+
+	return 0;
+
+child_out:
+	fwnode_handle_put(child);
+	return ret;
+}
+
+static int lp50xx_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct lp50xx *led;
+	int count;
+	int ret;
+
+	count = device_get_child_node_count(&client->dev);
+	if (!count) {
+		dev_err(&client->dev, "LEDs are not defined in device tree!");
+		return -ENODEV;
+	}
+
+	led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+			   GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	mutex_init(&led->lock);
+	led->client = client;
+	led->dev = &client->dev;
+	led->chip_info = &lp50xx_chip_info_tbl[id->driver_data];
+	i2c_set_clientdata(client, led);
+	led->regmap = devm_regmap_init_i2c(client,
+					led->chip_info->lp50xx_regmap_config);
+	if (IS_ERR(led->regmap)) {
+		ret = PTR_ERR(led->regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = lp50xx_reset(led);
+	if (ret)
+		return ret;
+
+	ret = lp50xx_enable_disable(led, 1);
+	if (ret)
+		return ret;
+
+	return lp50xx_probe_dt(led);
+}
+
+static int lp50xx_remove(struct i2c_client *client)
+{
+	struct lp50xx *led = i2c_get_clientdata(client);
+	int ret;
+
+	ret = lp50xx_enable_disable(led, 0);
+	if (ret) {
+		dev_err(&led->client->dev, "Failed to disable chip\n");
+		return ret;
+	}
+
+	if (led->regulator) {
+		ret = regulator_disable(led->regulator);
+		if (ret)
+			dev_err(&led->client->dev,
+				"Failed to disable regulator\n");
+	}
+
+	mutex_destroy(&led->lock);
+
+	return 0;
+}
+
+static const struct i2c_device_id lp50xx_id[] = {
+	{ "lp5009", LP5009 },
+	{ "lp5012", LP5012 },
+	{ "lp5018", LP5018 },
+	{ "lp5024", LP5024 },
+	{ "lp5030", LP5030 },
+	{ "lp5036", LP5036 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, lp50xx_id);
+
+static const struct of_device_id of_lp50xx_leds_match[] = {
+	{ .compatible = "ti,lp5009", .data = (void *)LP5009 },
+	{ .compatible = "ti,lp5012", .data = (void *)LP5012 },
+	{ .compatible = "ti,lp5018", .data = (void *)LP5018 },
+	{ .compatible = "ti,lp5024", .data = (void *)LP5024 },
+	{ .compatible = "ti,lp5030", .data = (void *)LP5030 },
+	{ .compatible = "ti,lp5036", .data = (void *)LP5036 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lp50xx_leds_match);
+
+static struct i2c_driver lp50xx_driver = {
+	.driver = {
+		.name	= "lp50xx",
+		.of_match_table = of_lp50xx_leds_match,
+	},
+	.probe		= lp50xx_probe,
+	.remove		= lp50xx_remove,
+	.id_table	= lp50xx_id,
+};
+module_i2c_driver(lp50xx_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LP50XX LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.28.0

[PATCH v33 2/6] leds: lp50xx: Add the LP50XX family of the RGB LED driver

[Dan Murphy]

Introduce the LP5036/30/24/18/12/9 RGB LED driver.
The difference in these parts are the number of
LED outputs where the:

LP5036 can control 36 LEDs
LP5030 can control 30 LEDs
LP5024 can control 24 LEDs
LP5018 can control 18 LEDs
LP5012 can control 12 LEDs
LP5009 can control 9 LEDs

The device has the ability to group LED outputs into control banks
so that multiple LED banks can be controlled with the same mixing and
brightness. Or the LED outputs can also be controlled independently.

Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 drivers/leds/Kconfig       |  11 +
 drivers/leds/Makefile      |   1 +
 drivers/leds/leds-lp50xx.c | 634 +++++++++++++++++++++++++++++++++++++
 3 files changed, 646 insertions(+)
 create mode 100644 drivers/leds/leds-lp50xx.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 1c181df24eae..00b488915945 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -395,6 +395,17 @@ config LEDS_LP3952
 	  To compile this driver as a module, choose M here: the
 	  module will be called leds-lp3952.
 
+config LEDS_LP50XX
+	tristate "LED Support for TI LP5036/30/24/18/12/9 LED driver chip"
+	depends on LEDS_CLASS && REGMAP_I2C
+	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
+	help
+	  If you say yes here you get support for the Texas Instruments
+	  LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called leds-lp50xx.
+
 config LEDS_LP55XX_COMMON
 	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 	depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index c2c7d7ade0d0..778cb4bb8c52 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_LEDS_LM3697)		+= leds-lm3697.o
 obj-$(CONFIG_LEDS_LOCOMO)		+= leds-locomo.o
 obj-$(CONFIG_LEDS_LP3944)		+= leds-lp3944.o
 obj-$(CONFIG_LEDS_LP3952)		+= leds-lp3952.o
+obj-$(CONFIG_LEDS_LP50XX)		+= leds-lp50xx.o
 obj-$(CONFIG_LEDS_LP5521)		+= leds-lp5521.o
 obj-$(CONFIG_LEDS_LP5523)		+= leds-lp5523.o
 obj-$(CONFIG_LEDS_LP5562)		+= leds-lp5562.o
diff --git a/drivers/leds/leds-lp50xx.c b/drivers/leds/leds-lp50xx.c
new file mode 100644
index 000000000000..47144a37cb94
--- /dev/null
+++ b/drivers/leds/leds-lp50xx.c
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LP50XX LED chip family driver
+// Copyright (C) 2018-20 Texas Instruments Incorporated - https://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#include <linux/led-class-multicolor.h>
+
+#include "leds.h"
+
+#define LP50XX_DEV_CFG0		0x00
+#define LP50XX_DEV_CFG1		0x01
+#define LP50XX_LED_CFG0		0x02
+
+/* LP5009 and LP5012 registers */
+#define LP5012_BNK_BRT		0x03
+#define LP5012_BNKA_CLR		0x04
+#define LP5012_BNKB_CLR		0x05
+#define LP5012_BNKC_CLR		0x06
+#define LP5012_LED0_BRT		0x07
+#define LP5012_OUT0_CLR		0x0b
+#define LP5012_RESET		0x17
+
+/* LP5018 and LP5024 registers */
+#define LP5024_BNK_BRT		0x03
+#define LP5024_BNKA_CLR		0x04
+#define LP5024_BNKB_CLR		0x05
+#define LP5024_BNKC_CLR		0x06
+#define LP5024_LED0_BRT		0x07
+#define LP5024_OUT0_CLR		0x0f
+#define LP5024_RESET		0x27
+
+/* LP5030 and LP5036 registers */
+#define LP5036_LED_CFG1		0x03
+#define LP5036_BNK_BRT		0x04
+#define LP5036_BNKA_CLR		0x05
+#define LP5036_BNKB_CLR		0x06
+#define LP5036_BNKC_CLR		0x07
+#define LP5036_LED0_BRT		0x08
+#define LP5036_OUT0_CLR		0x14
+#define LP5036_RESET		0x38
+
+#define LP50XX_SW_RESET		0xff
+#define LP50XX_CHIP_EN		BIT(6)
+
+/* There are 3 LED outputs per bank */
+#define LP50XX_LEDS_PER_MODULE	3
+
+#define LP5009_MAX_LED_MODULES	2
+#define LP5012_MAX_LED_MODULES	4
+#define LP5018_MAX_LED_MODULES	6
+#define LP5024_MAX_LED_MODULES	8
+#define LP5030_MAX_LED_MODULES	10
+#define LP5036_MAX_LED_MODULES	12
+
+static const struct reg_default lp5012_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5012_BNK_BRT, 0xff},
+	{LP5012_BNKA_CLR, 0x0f},
+	{LP5012_BNKB_CLR, 0x0f},
+	{LP5012_BNKC_CLR, 0x0f},
+	{LP5012_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff},
+	{LP5012_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x0c, 0x00}, {0x0d, 0x00}, {0x0e, 0x00}, {0x0f, 0x00}, {0x10, 0x00},
+	{0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00},	{0x15, 0x00},
+	{0x16, 0x00},
+	{LP5012_RESET, 0x00}
+};
+
+static const struct reg_default lp5024_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5024_BNK_BRT, 0xff},
+	{LP5024_BNKA_CLR, 0x0f},
+	{LP5024_BNKB_CLR, 0x0f},
+	{LP5024_BNKC_CLR, 0x0f},
+	{LP5024_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+	{0x0d, 0xff}, {0x0e, 0xff},
+	{LP5024_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x10, 0x00}, {0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00},
+	{0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+	{0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+	{0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+	{0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00},
+	{LP5024_RESET, 0x00}
+};
+
+static const struct reg_default lp5036_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5036_LED_CFG1, 0x0},
+	{LP5036_BNK_BRT, 0xff},
+	{LP5036_BNKA_CLR, 0x0f},
+	{LP5036_BNKB_CLR, 0x0f},
+	{LP5036_BNKC_CLR, 0x0f},
+	{LP5036_LED0_BRT, 0x0f},
+	/* LEDX_BRT registers are all 0xff for defaults */
+	{0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+	{0x0d, 0xff}, {0x0e, 0xff}, {0x0f, 0xff}, {0x10, 0xff}, {0x11, 0xff},
+	{0x12, 0xff}, {0x13, 0xff},
+	{LP5036_OUT0_CLR, 0x0f},
+	/* OUTX_CLR registers are all 0x0 for defaults */
+	{0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+	{0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+	{0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+	{0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
+	{0x29, 0x00}, {0x2a, 0x00}, {0x2b, 0x00}, {0x2c, 0x00}, {0x2d, 0x00},
+	{0x2e, 0x00}, {0x2f, 0x00}, {0x30, 0x00}, {0x31, 0x00}, {0x32, 0x00},
+	{0x33, 0x00}, {0x34, 0x00}, {0x35, 0x00}, {0x36, 0x00}, {0x37, 0x00},
+	{LP5036_RESET, 0x00}
+};
+
+static const struct regmap_config lp5012_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5012_RESET,
+	.reg_defaults = lp5012_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5012_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5024_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5024_RESET,
+	.reg_defaults = lp5024_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5024_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5036_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5036_RESET,
+	.reg_defaults = lp5036_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5036_reg_defs),
+	.cache_type = REGCACHE_FLAT,
+};
+
+enum lp50xx_model {
+	LP5009,
+	LP5012,
+	LP5018,
+	LP5024,
+	LP5030,
+	LP5036,
+};
+
+/**
+ * struct lp50xx_chip_info -
+ * @lp50xx_regmap_config: regmap register configuration
+ * @model_id: LED device model
+ * @max_modules: total number of supported LED modules
+ * @num_leds: number of LED outputs available on the device
+ * @led_brightness0_reg: first brightness register of the device
+ * @mix_out0_reg: first color mix register of the device
+ * @bank_brt_reg: bank brightness register
+ * @bank_mix_reg: color mix register
+ * @reset_reg: device reset register
+ */
+struct lp50xx_chip_info {
+	const struct regmap_config *lp50xx_regmap_config;
+	int model_id;
+	u8 max_modules;
+	u8 num_leds;
+	u8 led_brightness0_reg;
+	u8 mix_out0_reg;
+	u8 bank_brt_reg;
+	u8 bank_mix_reg;
+	u8 reset_reg;
+};
+
+static const struct lp50xx_chip_info lp50xx_chip_info_tbl[] = {
+	[LP5009] = {
+		.model_id = LP5009,
+		.max_modules = LP5009_MAX_LED_MODULES,
+		.num_leds = LP5009_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = &lp5012_regmap_config,
+	},
+	[LP5012] = {
+		.model_id = LP5012,
+		.max_modules = LP5012_MAX_LED_MODULES,
+		.num_leds = LP5012_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = &lp5012_regmap_config,
+	},
+	[LP5018] = {
+		.model_id = LP5018,
+		.max_modules = LP5018_MAX_LED_MODULES,
+		.num_leds = LP5018_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = &lp5024_regmap_config,
+	},
+	[LP5024] = {
+		.model_id = LP5024,
+		.max_modules = LP5024_MAX_LED_MODULES,
+		.num_leds = LP5024_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = &lp5024_regmap_config,
+	},
+	[LP5030] = {
+		.model_id = LP5030,
+		.max_modules = LP5030_MAX_LED_MODULES,
+		.num_leds = LP5030_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = &lp5036_regmap_config,
+	},
+	[LP5036] = {
+		.model_id = LP5036,
+		.max_modules = LP5036_MAX_LED_MODULES,
+		.num_leds = LP5036_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = &lp5036_regmap_config,
+	},
+};
+
+struct lp50xx_led {
+	struct led_classdev_mc mc_cdev;
+	struct lp50xx *priv;
+	unsigned long bank_modules;
+	int led_intensity[LP50XX_LEDS_PER_MODULE];
+	u8 ctrl_bank_enabled;
+	int led_number;
+};
+
+/**
+ * struct lp50xx -
+ * @enable_gpio: hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: pointer to the I2C client
+ * @regmap: device register map
+ * @dev: pointer to the devices device struct
+ * @lock: lock for reading/writing the device
+ * @chip_info: chip specific information (ie num_leds)
+ * @num_of_banked_leds: holds the number of banked LEDs
+ * @leds: array of LED strings
+ */
+struct lp50xx {
+	struct gpio_desc *enable_gpio;
+	struct regulator *regulator;
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct device *dev;
+	struct mutex lock;
+	const struct lp50xx_chip_info *chip_info;
+	int num_of_banked_leds;
+
+	/* This needs to be at the end of the struct */
+	struct lp50xx_led leds[];
+};
+
+static struct lp50xx_led *mcled_cdev_to_led(struct led_classdev_mc *mc_cdev)
+{
+	return container_of(mc_cdev, struct lp50xx_led, mc_cdev);
+}
+
+static int lp50xx_brightness_set(struct led_classdev *cdev,
+			     enum led_brightness brightness)
+{
+	struct led_classdev_mc *mc_dev = lcdev_to_mccdev(cdev);
+	struct lp50xx_led *led = mcled_cdev_to_led(mc_dev);
+	const struct lp50xx_chip_info *led_chip = led->priv->chip_info;
+	u8 led_offset, reg_val;
+	int ret = 0;
+	int i;
+
+	mutex_lock(&led->priv->lock);
+	if (led->ctrl_bank_enabled)
+		reg_val = led_chip->bank_brt_reg;
+	else
+		reg_val = led_chip->led_brightness0_reg +
+			  led->led_number;
+
+	ret = regmap_write(led->priv->regmap, reg_val, brightness);
+	if (ret) {
+		dev_err(&led->priv->client->dev,
+			"Cannot write brightness value %d\n", ret);
+		goto out;
+	}
+
+	for (i = 0; i < led->mc_cdev.num_colors; i++) {
+		if (led->ctrl_bank_enabled) {
+			reg_val = led_chip->bank_mix_reg + i;
+		} else {
+			led_offset = (led->led_number * 3) + i;
+			reg_val = led_chip->mix_out0_reg + led_offset;
+		}
+
+		ret = regmap_write(led->priv->regmap, reg_val,
+				   mc_dev->subled_info[i].intensity);
+		if (ret) {
+			dev_err(&led->priv->client->dev,
+				"Cannot write intensity value %d\n", ret);
+			goto out;
+		}
+	}
+out:
+	mutex_unlock(&led->priv->lock);
+	return ret;
+}
+
+static int lp50xx_set_banks(struct lp50xx *priv, u32 led_banks[])
+{
+	u8 led_config_lo, led_config_hi;
+	u32 bank_enable_mask = 0;
+	int ret;
+	int i;
+
+	for (i = 0; i < priv->chip_info->max_modules; i++) {
+		if (led_banks[i])
+			bank_enable_mask |= (1 << led_banks[i]);
+	}
+
+	led_config_lo = (u8)(bank_enable_mask & 0xff);
+	led_config_hi = (u8)(bank_enable_mask >> 8) & 0xff;
+
+	ret = regmap_write(priv->regmap, LP50XX_LED_CFG0, led_config_lo);
+	if (ret)
+		return ret;
+
+	if (priv->chip_info->model_id >= LP5030)
+		ret = regmap_write(priv->regmap, LP5036_LED_CFG1, led_config_hi);
+
+	return ret;
+}
+
+static int lp50xx_reset(struct lp50xx *priv)
+{
+	return regmap_write(priv->regmap, priv->chip_info->reset_reg, LP50XX_SW_RESET);
+}
+
+static int lp50xx_enable_disable(struct lp50xx *priv, int enable_disable)
+{
+	int ret;
+
+	if (priv->enable_gpio) {
+		ret = gpiod_direction_output(priv->enable_gpio, enable_disable);
+		if (ret)
+			return ret;
+	}
+
+	if (enable_disable)
+		return regmap_write(priv->regmap, LP50XX_DEV_CFG0, LP50XX_CHIP_EN);
+	else
+		return regmap_write(priv->regmap, LP50XX_DEV_CFG0, 0);
+
+}
+
+static int lp50xx_probe_leds(struct fwnode_handle *child, struct lp50xx *priv,
+			     struct lp50xx_led *led, int num_leds)
+{
+	u32 led_banks[LP5036_MAX_LED_MODULES] = {0};
+	int led_number;
+	int ret;
+
+	if (num_leds > 1) {
+		if (num_leds > priv->chip_info->max_modules) {
+			dev_err(&priv->client->dev, "reg property is invalid\n");
+			return -EINVAL;
+		}
+
+		priv->num_of_banked_leds = num_leds;
+
+		ret = fwnode_property_read_u32_array(child, "reg", led_banks, num_leds);
+		if (ret) {
+			dev_err(&priv->client->dev, "reg property is missing\n");
+			return ret;
+		}
+
+		ret = lp50xx_set_banks(priv, led_banks);
+		if (ret) {
+			dev_err(&priv->client->dev, "Cannot setup banked LEDs\n");
+			return ret;
+		}
+
+		led->ctrl_bank_enabled = 1;
+	} else {
+		ret = fwnode_property_read_u32(child, "reg", &led_number);
+		if (ret) {
+			dev_err(&priv->client->dev, "led reg property missing\n");
+			return ret;
+		}
+
+		if (led_number > priv->chip_info->num_leds) {
+			dev_err(&priv->client->dev, "led-sources property is invalid\n");
+			return -EINVAL;
+		}
+
+		led->led_number = led_number;
+	}
+
+	return 0;
+}
+
+static int lp50xx_probe_dt(struct lp50xx *priv)
+{
+	struct fwnode_handle *child = NULL;
+	struct fwnode_handle *led_node = NULL;
+	struct led_init_data init_data = {};
+	struct led_classdev *led_cdev;
+	struct mc_subled *mc_led_info;
+	struct lp50xx_led *led;
+	int ret = -EINVAL;
+	int num_colors;
+	u32 color_id;
+	int i = 0;
+
+	priv->enable_gpio = devm_gpiod_get_optional(priv->dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->enable_gpio)) {
+		ret = PTR_ERR(priv->enable_gpio);
+		dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+			ret);
+		return ret;
+	}
+
+	priv->regulator = devm_regulator_get(priv->dev, "vled");
+	if (IS_ERR(priv->regulator))
+		priv->regulator = NULL;
+
+	device_for_each_child_node(priv->dev, child) {
+		led = &priv->leds[i];
+		ret = fwnode_property_count_u32(child, "reg");
+		if (ret < 0) {
+			dev_err(&priv->client->dev, "reg property is invalid\n");
+			goto child_out;
+		}
+
+		ret = lp50xx_probe_leds(child, priv, led, ret);
+		if (ret)
+			goto child_out;
+
+		init_data.fwnode = child;
+		num_colors = 0;
+
+		/*
+		 * There are only 3 LEDs per module otherwise they should be
+		 * banked which also is presented as 3 LEDs.
+		 */
+		mc_led_info = devm_kcalloc(priv->dev, LP50XX_LEDS_PER_MODULE,
+					   sizeof(*mc_led_info), GFP_KERNEL);
+		if (!mc_led_info)
+			return -ENOMEM;
+
+		fwnode_for_each_child_node(child, led_node) {
+			ret = fwnode_property_read_u32(led_node, "color",
+						       &color_id);
+			if (ret) {
+				dev_err(priv->dev, "Cannot read color\n");
+				goto child_out;
+			}
+
+			mc_led_info[num_colors].color_index = color_id;
+			num_colors++;
+		}
+
+		led->priv = priv;
+		led->mc_cdev.num_colors = num_colors;
+		led->mc_cdev.subled_info = mc_led_info;
+		led_cdev = &led->mc_cdev.led_cdev;
+		led_cdev->brightness_set_blocking = lp50xx_brightness_set;
+
+		fwnode_property_read_string(child, "linux,default-trigger",
+					    &led_cdev->default_trigger);
+
+		ret = devm_led_classdev_multicolor_register_ext(&priv->client->dev,
+						       &led->mc_cdev,
+						       &init_data);
+		if (ret) {
+			dev_err(&priv->client->dev, "led register err: %d\n",
+				ret);
+			goto child_out;
+		}
+		i++;
+		fwnode_handle_put(child);
+	}
+
+	return 0;
+
+child_out:
+	fwnode_handle_put(child);
+	return ret;
+}
+
+static int lp50xx_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct lp50xx *led;
+	int count;
+	int ret;
+
+	count = device_get_child_node_count(&client->dev);
+	if (!count) {
+		dev_err(&client->dev, "LEDs are not defined in device tree!");
+		return -ENODEV;
+	}
+
+	led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+			   GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	mutex_init(&led->lock);
+	led->client = client;
+	led->dev = &client->dev;
+	led->chip_info = &lp50xx_chip_info_tbl[id->driver_data];
+	i2c_set_clientdata(client, led);
+	led->regmap = devm_regmap_init_i2c(client,
+					led->chip_info->lp50xx_regmap_config);
+	if (IS_ERR(led->regmap)) {
+		ret = PTR_ERR(led->regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = lp50xx_reset(led);
+	if (ret)
+		return ret;
+
+	ret = lp50xx_enable_disable(led, 1);
+	if (ret)
+		return ret;
+
+	return lp50xx_probe_dt(led);
+}
+
+static int lp50xx_remove(struct i2c_client *client)
+{
+	struct lp50xx *led = i2c_get_clientdata(client);
+	int ret;
+
+	ret = lp50xx_enable_disable(led, 0);
+	if (ret) {
+		dev_err(&led->client->dev, "Failed to disable chip\n");
+		return ret;
+	}
+
+	if (led->regulator) {
+		ret = regulator_disable(led->regulator);
+		if (ret)
+			dev_err(&led->client->dev,
+				"Failed to disable regulator\n");
+	}
+
+	mutex_destroy(&led->lock);
+
+	return 0;
+}
+
+static const struct i2c_device_id lp50xx_id[] = {
+	{ "lp5009", LP5009 },
+	{ "lp5012", LP5012 },
+	{ "lp5018", LP5018 },
+	{ "lp5024", LP5024 },
+	{ "lp5030", LP5030 },
+	{ "lp5036", LP5036 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, lp50xx_id);
+
+static const struct of_device_id of_lp50xx_leds_match[] = {
+	{ .compatible = "ti,lp5009", .data = (void *)LP5009 },
+	{ .compatible = "ti,lp5012", .data = (void *)LP5012 },
+	{ .compatible = "ti,lp5018", .data = (void *)LP5018 },
+	{ .compatible = "ti,lp5024", .data = (void *)LP5024 },
+	{ .compatible = "ti,lp5030", .data = (void *)LP5030 },
+	{ .compatible = "ti,lp5036", .data = (void *)LP5036 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lp50xx_leds_match);
+
+static struct i2c_driver lp50xx_driver = {
+	.driver = {
+		.name	= "lp50xx",
+		.of_match_table = of_lp50xx_leds_match,
+	},
+	.probe		= lp50xx_probe,
+	.remove		= lp50xx_remove,
+	.id_table	= lp50xx_id,
+};
+module_i2c_driver(lp50xx_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LP50XX LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 3/6] ARM: defconfig: u8500: Add LP55XX_COMMON config flag

[Dan Murphy]

The dependencies for the LP55XX LED drivers have been updated so that
the child devices (i.e. LP5521) now depends on the LP55XX_COMMON config
flag as opposed to the device selecting the LP55XX_COMMON flag.  The
LP55XX_COMMON needs to be set in the defconfig.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 arch/arm/configs/u8500_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 28dd7cf56048..dea599e1c17e 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -113,6 +113,7 @@ CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_LP55XX_COMMON=y
 CONFIG_LEDS_LP5521=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
-- 
2.28.0

[PATCH v33 3/6] ARM: defconfig: u8500: Add LP55XX_COMMON config flag

[Dan Murphy]

The dependencies for the LP55XX LED drivers have been updated so that
the child devices (i.e. LP5521) now depends on the LP55XX_COMMON config
flag as opposed to the device selecting the LP55XX_COMMON flag.  The
LP55XX_COMMON needs to be set in the defconfig.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 arch/arm/configs/u8500_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 28dd7cf56048..dea599e1c17e 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -113,6 +113,7 @@ CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_LP55XX_COMMON=y
 CONFIG_LEDS_LP5521=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 4/6] ARM: dts: n900: Add reg property to the LP5523 channel node

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
CC: Tony Lindgren <tony@atomide.com>
CC: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 arch/arm/boot/dts/omap3-n900.dts | 29 ++++++++++++++++++++---------
 1 file changed, 20 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 4089d97405c9..ebe93b06b4f7 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -618,63 +618,74 @@ indicator {
 	};
 
 	lp5523: lp5523@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "national,lp5523";
 		reg = <0x32>;
 		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
 		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 
-		chan0 {
+		chan@0 {
 			chan-name = "lp5523:kb1";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <0>;
 		};
 
-		chan1 {
+		chan@1 {
 			chan-name = "lp5523:kb2";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <1>;
 		};
 
-		chan2 {
+		chan@2 {
 			chan-name = "lp5523:kb3";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <2>;
 		};
 
-		chan3 {
+		chan@3 {
 			chan-name = "lp5523:kb4";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <3>;
 		};
 
-		chan4 {
+		chan@4 {
 			chan-name = "lp5523:b";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <4>;
 		};
 
-		chan5 {
+		chan@5 {
 			chan-name = "lp5523:g";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <5>;
 		};
 
-		chan6 {
+		chan@6 {
 			chan-name = "lp5523:r";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <6>;
 		};
 
-		chan7 {
+		chan@7 {
 			chan-name = "lp5523:kb5";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <7>;
 		};
 
-		chan8 {
+		chan@8 {
 			chan-name = "lp5523:kb6";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <8>;
 		};
 	};
 
-- 
2.28.0

[PATCH v33 4/6] ARM: dts: n900: Add reg property to the LP5523 channel node

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
CC: Tony Lindgren <tony@atomide.com>
CC: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 arch/arm/boot/dts/omap3-n900.dts | 29 ++++++++++++++++++++---------
 1 file changed, 20 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 4089d97405c9..ebe93b06b4f7 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -618,63 +618,74 @@ indicator {
 	};
 
 	lp5523: lp5523@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "national,lp5523";
 		reg = <0x32>;
 		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
 		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 
-		chan0 {
+		chan@0 {
 			chan-name = "lp5523:kb1";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <0>;
 		};
 
-		chan1 {
+		chan@1 {
 			chan-name = "lp5523:kb2";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <1>;
 		};
 
-		chan2 {
+		chan@2 {
 			chan-name = "lp5523:kb3";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <2>;
 		};
 
-		chan3 {
+		chan@3 {
 			chan-name = "lp5523:kb4";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <3>;
 		};
 
-		chan4 {
+		chan@4 {
 			chan-name = "lp5523:b";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <4>;
 		};
 
-		chan5 {
+		chan@5 {
 			chan-name = "lp5523:g";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <5>;
 		};
 
-		chan6 {
+		chan@6 {
 			chan-name = "lp5523:r";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <6>;
 		};
 
-		chan7 {
+		chan@7 {
 			chan-name = "lp5523:kb5";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <7>;
 		};
 
-		chan8 {
+		chan@8 {
 			chan-name = "lp5523:kb6";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			reg = <8>;
 		};
 	};
 
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 5/6] ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
---
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
index 2b9423d55c37..77aa90640052 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -258,29 +258,35 @@ leds: led-controller@30 {
 		reg = <0x30>;
 		clock-mode = /bits/ 8 <1>;
 		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		chan0 {
+		chan@0 {
 			chan-name = "R";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <0>;
 		};
 
-		chan1 {
+		chan@1 {
 			chan-name = "G";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <1>;
 		};
 
-		chan2 {
+		chan@2 {
 			chan-name = "B";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <2>;
 		};
 
-		chan3 {
+		chan@3 {
 			chan-name = "W";
 			led-cur = /bits/ 8 <0x0>;
 			max-cur = /bits/ 8 <0x0>;
+			reg = <3>;
 		};
 	};
 
-- 
2.28.0

[PATCH v33 5/6] ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
---
 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
index 2b9423d55c37..77aa90640052 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -258,29 +258,35 @@ leds: led-controller@30 {
 		reg = <0x30>;
 		clock-mode = /bits/ 8 <1>;
 		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		chan0 {
+		chan@0 {
 			chan-name = "R";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <0>;
 		};
 
-		chan1 {
+		chan@1 {
 			chan-name = "G";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <1>;
 		};
 
-		chan2 {
+		chan@2 {
 			chan-name = "B";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <2>;
 		};
 
-		chan3 {
+		chan@3 {
 			chan-name = "W";
 			led-cur = /bits/ 8 <0x0>;
 			max-cur = /bits/ 8 <0x0>;
+			reg = <3>;
 		};
 	};
 
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 5/6] ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node

[Shawn Guo]

On Wed, Aug 12, 2020 at 02:50:19PM -0500, Dan Murphy wrote:
> Add the reg property to each channel node.  This update is
> to accommodate the multicolor framework.  In addition to the
> accommodation this allows the LEDs to be placed on any channel
> and allow designs to skip channels as opposed to requiring
> sequential order.
> 
> Acked-by: Pavel Machek <pavel@ucw.cz>
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> CC: Shawn Guo <shawnguo@kernel.org>
> CC: Sascha Hauer <s.hauer@pengutronix.de>
> CC: Pengutronix Kernel Team <kernel@pengutronix.de>
> CC: Fabio Estevam <festevam@gmail.com>
> CC: NXP Linux Team <linux-imx@nxp.com>

Applied, thanks.

Re: [PATCH v33 5/6] ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 channel node

[Shawn Guo]

On Wed, Aug 12, 2020 at 02:50:19PM -0500, Dan Murphy wrote:
> Add the reg property to each channel node.  This update is
> to accommodate the multicolor framework.  In addition to the
> accommodation this allows the LEDs to be placed on any channel
> and allow designs to skip channels as opposed to requiring
> sequential order.
> 
> Acked-by: Pavel Machek <pavel@ucw.cz>
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> CC: Shawn Guo <shawnguo@kernel.org>
> CC: Sascha Hauer <s.hauer@pengutronix.de>
> CC: Pengutronix Kernel Team <kernel@pengutronix.de>
> CC: Fabio Estevam <festevam@gmail.com>
> CC: NXP Linux Team <linux-imx@nxp.com>

Applied, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 arch/arm/boot/dts/ste-href.dtsi | 22 ++++++++++++++++------
 1 file changed, 16 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 33e3b0b3c53d..ff47cbf6ed3b 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -58,16 +58,21 @@ lp5521@33 {
 				reg = <0x33>;
 				label = "lp5521_pri";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				chan@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 					linux,default-trigger = "heartbeat";
 				};
-				chan1 {
+				chan@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan2 {
+				chan@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
@@ -77,15 +82,20 @@ lp5521@34 {
 				reg = <0x34>;
 				label = "lp5521_sec";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				chan@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan1 {
+				chan@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan2 {
+				chan@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-- 
2.28.0

[PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Dan Murphy]

Add the reg property to each channel node.  This update is
to accommodate the multicolor framework.  In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 arch/arm/boot/dts/ste-href.dtsi | 22 ++++++++++++++++------
 1 file changed, 16 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 33e3b0b3c53d..ff47cbf6ed3b 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -58,16 +58,21 @@ lp5521@33 {
 				reg = <0x33>;
 				label = "lp5521_pri";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				chan@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 					linux,default-trigger = "heartbeat";
 				};
-				chan1 {
+				chan@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan2 {
+				chan@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
@@ -77,15 +82,20 @@ lp5521@34 {
 				reg = <0x34>;
 				label = "lp5521_sec";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				chan@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan1 {
+				chan@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-				chan2 {
+				chan@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
 				};
-- 
2.28.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Linus Walleij]

On Wed, Aug 12, 2020 at 9:50 PM Dan Murphy <dmurphy@ti.com> wrote:

> Add the reg property to each channel node.  This update is
> to accommodate the multicolor framework.  In addition to the
> accommodation this allows the LEDs to be placed on any channel
> and allow designs to skip channels as opposed to requiring
> sequential order.
>
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> CC: Linus Walleij <linus.walleij@linaro.org>
> Acked-by: Pavel Machek <pavel@ucw.cz>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

I don't knof if I should just apply these two patches or if there are
dependencies that need to go in first. I guess yes?

Yours,
Linus Walleij

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Linus Walleij]

On Wed, Aug 12, 2020 at 9:50 PM Dan Murphy <dmurphy@ti.com> wrote:

> Add the reg property to each channel node.  This update is
> to accommodate the multicolor framework.  In addition to the
> accommodation this allows the LEDs to be placed on any channel
> and allow designs to skip channels as opposed to requiring
> sequential order.
>
> Signed-off-by: Dan Murphy <dmurphy@ti.com>
> CC: Linus Walleij <linus.walleij@linaro.org>
> Acked-by: Pavel Machek <pavel@ucw.cz>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

I don't knof if I should just apply these two patches or if there are
dependencies that need to go in first. I guess yes?

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Dan Murphy]

Linus

On 8/27/20 5:58 PM, Linus Walleij wrote:
> On Wed, Aug 12, 2020 at 9:50 PM Dan Murphy <dmurphy@ti.com> wrote:
>
>> Add the reg property to each channel node.  This update is
>> to accommodate the multicolor framework.  In addition to the
>> accommodation this allows the LEDs to be placed on any channel
>> and allow designs to skip channels as opposed to requiring
>> sequential order.
>>
>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>> CC: Linus Walleij <linus.walleij@linaro.org>
>> Acked-by: Pavel Machek <pavel@ucw.cz>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
>
> I don't knof if I should just apply these two patches or if there are
> dependencies that need to go in first. I guess yes?

I believe all dependencies have been met for these

Dan

> Yours,
> Linus Walleij

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Dan Murphy]

Linus

On 8/27/20 5:58 PM, Linus Walleij wrote:
> On Wed, Aug 12, 2020 at 9:50 PM Dan Murphy <dmurphy@ti.com> wrote:
>
>> Add the reg property to each channel node.  This update is
>> to accommodate the multicolor framework.  In addition to the
>> accommodation this allows the LEDs to be placed on any channel
>> and allow designs to skip channels as opposed to requiring
>> sequential order.
>>
>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>> CC: Linus Walleij <linus.walleij@linaro.org>
>> Acked-by: Pavel Machek <pavel@ucw.cz>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
>
> I don't knof if I should just apply these two patches or if there are
> dependencies that need to go in first. I guess yes?

I believe all dependencies have been met for these

Dan

> Yours,
> Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Linus Walleij]

On Fri, Aug 28, 2020 at 8:39 PM Dan Murphy <dmurphy@ti.com> wrote:

> > I don't knof if I should just apply these two patches or if there are
> > dependencies that need to go in first. I guess yes?
>
> I believe all dependencies have been met for these

OK I applied this patch to the Ux500 tree!

Yours,
Linus Walleij

Re: [PATCH v33 6/6] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes

[Linus Walleij]

On Fri, Aug 28, 2020 at 8:39 PM Dan Murphy <dmurphy@ti.com> wrote:

> > I don't knof if I should just apply these two patches or if there are
> > dependencies that need to go in first. I guess yes?
>
> I believe all dependencies have been met for these

OK I applied this patch to the Ux500 tree!

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 529 bytes --]

Hi!

> These are the final patches from the original multicolor framework patchset.
> 
> Changes made were to the LP50xx to rework regmap_defaults to eliminate used
> only once #defines.  Also fixed putting the child node in the dt parsing and
> changed regmap regcache type to flat.

Thanks. I applied 1 and 2 of the series to the for-next branch.

Best regards,
								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

Re: [PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Pavel Machek]

[-- Attachment #1.1: Type: text/plain, Size: 529 bytes --]

Hi!

> These are the final patches from the original multicolor framework patchset.
> 
> Changes made were to the LP50xx to rework regmap_defaults to eliminate used
> only once #defines.  Also fixed putting the child node in the dt parsing and
> changed regmap regcache type to flat.

Thanks. I applied 1 and 2 of the series to the for-next branch.

Best regards,
								Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #1.2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Dan Murphy]

Pavel

On 8/17/20 3:35 PM, Pavel Machek wrote:
> Hi!
>
>> These are the final patches from the original multicolor framework patchset.
>>
>> Changes made were to the LP50xx to rework regmap_defaults to eliminate used
>> only once #defines.  Also fixed putting the child node in the dt parsing and
>> changed regmap regcache type to flat.
> Thanks. I applied 1 and 2 of the series to the for-next branch.

Thanks.  The DT files are not really a major issue.  But the defconfig 
is not sure who to ping to have them pull it.

Maybe Linus W?

Dan

> Best regards,
> 								Pavel

Re: [PATCH v33 0/6] LP50xx addition and remainder Multicolor patches

[Dan Murphy]

Pavel

On 8/17/20 3:35 PM, Pavel Machek wrote:
> Hi!
>
>> These are the final patches from the original multicolor framework patchset.
>>
>> Changes made were to the LP50xx to rework regmap_defaults to eliminate used
>> only once #defines.  Also fixed putting the child node in the dt parsing and
>> changed regmap regcache type to flat.
> Thanks. I applied 1 and 2 of the series to the for-next branch.

Thanks.  The DT files are not really a major issue.  But the defconfig 
is not sure who to ping to have them pull it.

Maybe Linus W?

Dan

> Best regards,
> 								Pavel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel