[PATCH v3 0/2] wcn36xx: Enable VHT when supported

[PATCH v3 0/2] wcn36xx: Enable VHT when supported

[Bryan O'Donoghue]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This series is six in a set of seven to add support for wcn3680 at 802.11ac
data-rates.

These two commits have been moved later in the set of commits so that the
patches to enable advertisement of VHT capabilities happen after all of the
supporting code has been comitted.

Changes from V2:

- Rename "wcn36xx: Add ieee802.11 VHT flags" to "wcn36xx: Advertise
  ieee802.11 VHT flags"

https://lore.kernel.org/linux-wireless/20200829033908.2167689-5-bryan.odonoghue@linaro.org/T/#u
https://lore.kernel.org/linux-wireless/20200829033846.2167619-4-bryan.odonoghue@linaro.org/T/#u


Bryan O'Donoghue (2):
  wcn36xx: Add VHT rates to wcn36xx_update_allowed_rates()
  wcn36xx: Advertise ieee802.11 VHT flags

 drivers/net/wireless/ath/wcn36xx/main.c | 40 +++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

-- 
2.27.0

[PATCH v3 1/2] wcn36xx: Add VHT rates to wcn36xx_update_allowed_rates()

[Bryan O'Donoghue]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/net/wireless/ath/wcn36xx/main.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/net/wireless/ath/wcn36xx/main.c b/drivers/net/wireless/ath/wcn36xx/main.c
index 2c2b6178c8cd..9c283c110e07 100644
--- a/drivers/net/wireless/ath/wcn36xx/main.c
+++ b/drivers/net/wireless/ath/wcn36xx/main.c
@@ -766,6 +766,14 @@ static void wcn36xx_update_allowed_rates(struct ieee80211_sta *sta,
 		       sta->ht_cap.mcs.rx_mask,
 		       sizeof(sta->ht_cap.mcs.rx_mask));
 	}
+
+	if (sta->vht_cap.vht_supported) {
+		sta_priv->supported_rates.op_rate_mode = STA_11ac;
+		sta_priv->supported_rates.vht_rx_mcs_map =
+				sta->vht_cap.vht_mcs.rx_mcs_map;
+		sta_priv->supported_rates.vht_tx_mcs_map =
+				sta->vht_cap.vht_mcs.tx_mcs_map;
+	}
 }
 void wcn36xx_set_default_rates(struct wcn36xx_hal_supported_rates *rates)
 {
-- 
2.27.0

[PATCH v3 2/2] wcn36xx: Advertise ieee802.11 VHT flags

[Bryan O'Donoghue]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds ieee802.11 VHT flags for the wcn3680b.

- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream

RX LDPC is declared as supported in the datasheet but not enabled at this
time.

After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/net/wireless/ath/wcn36xx/main.c | 32 +++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/drivers/net/wireless/ath/wcn36xx/main.c b/drivers/net/wireless/ath/wcn36xx/main.c
index 9c283c110e07..9e97513feeb5 100644
--- a/drivers/net/wireless/ath/wcn36xx/main.c
+++ b/drivers/net/wireless/ath/wcn36xx/main.c
@@ -1200,6 +1200,35 @@ static const struct ieee80211_ops wcn36xx_ops = {
 	CFG80211_TESTMODE_CMD(wcn36xx_tm_cmd)
 };
 
+static void
+wcn36xx_set_ieee80211_vht_caps(struct ieee80211_sta_vht_cap *vht_cap)
+{
+	vht_cap->vht_supported = true;
+
+	vht_cap->cap = (IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 |
+			IEEE80211_VHT_CAP_SHORT_GI_80 |
+			IEEE80211_VHT_CAP_RXSTBC_1 |
+			IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE |
+			IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE |
+			3 << IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT |
+			7 << IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT);
+
+	vht_cap->vht_mcs.rx_mcs_map =
+		cpu_to_le16(IEEE80211_VHT_MCS_SUPPORT_0_9 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 2 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 4 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 6 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 8 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 10 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 12 |
+			    IEEE80211_VHT_MCS_NOT_SUPPORTED << 14);
+
+	vht_cap->vht_mcs.rx_highest = cpu_to_le16(433);
+	vht_cap->vht_mcs.tx_highest = vht_cap->vht_mcs.rx_highest;
+
+	vht_cap->vht_mcs.tx_mcs_map = vht_cap->vht_mcs.rx_mcs_map;
+}
+
 static int wcn36xx_init_ieee80211(struct wcn36xx *wcn)
 {
 	static const u32 cipher_suites[] = {
@@ -1228,6 +1257,9 @@ static int wcn36xx_init_ieee80211(struct wcn36xx *wcn)
 		wcn->hw->wiphy->bands[NL80211_BAND_5GHZ] = &wcn_band_5ghz;
 	}
 
+	if (wcn->rf_id == RF_IRIS_WCN3680)
+		wcn36xx_set_ieee80211_vht_caps(&wcn_band_5ghz.vht_cap);
+
 	wcn->hw->wiphy->max_scan_ssids = WCN36XX_MAX_SCAN_SSIDS;
 	wcn->hw->wiphy->max_scan_ie_len = WCN36XX_MAX_SCAN_IE_LEN;
 
-- 
2.27.0

[PATCH v3 1/2] wcn36xx: Add VHT rates to wcn36xx_update_allowed_rates()

[Bryan O'Donoghue]

This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/net/wireless/ath/wcn36xx/main.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/net/wireless/ath/wcn36xx/main.c b/drivers/net/wireless/ath/wcn36xx/main.c
index 2c2b6178c8cd..9c283c110e07 100644
--- a/drivers/net/wireless/ath/wcn36xx/main.c
+++ b/drivers/net/wireless/ath/wcn36xx/main.c
@@ -766,6 +766,14 @@ static void wcn36xx_update_allowed_rates(struct ieee80211_sta *sta,
 		       sta->ht_cap.mcs.rx_mask,
 		       sizeof(sta->ht_cap.mcs.rx_mask));
 	}
+
+	if (sta->vht_cap.vht_supported) {
+		sta_priv->supported_rates.op_rate_mode = STA_11ac;
+		sta_priv->supported_rates.vht_rx_mcs_map =
+				sta->vht_cap.vht_mcs.rx_mcs_map;
+		sta_priv->supported_rates.vht_tx_mcs_map =
+				sta->vht_cap.vht_mcs.tx_mcs_map;
+	}
 }
 void wcn36xx_set_default_rates(struct wcn36xx_hal_supported_rates *rates)
 {
-- 
2.27.0