From: Neil Armstrong <narmstrong@baylibre.com> To: u-boot@lists.denx.de Subject: [PATCH 0/8] ARM: mach-meson: update & rework USB for GXL, GXM & AXG Date: Thu, 10 Sep 2020 10:48:11 +0200 [thread overview] Message-ID: <20200910084819.25312-1-narmstrong@baylibre.com> (raw) This serie follows the recent work under Linux to rework and update support of the USB complex in the Amlogic GXL, GXM & AXG SoCs. This rework follows the clean implementation for the G12A & following SoCs to support Host, Device & OTG functionnality. The GXL, GXM & AXG USB complex is architectured in the same was as the G12A & later USB complex, thus we can use the same architecture but adapted to the different init & config flow found in the Amlogic GXL, GXM & AXG SoCs. With this patchset, USB Host functionnality is retained, working & tested on the Khadas VIM2 (GXM), Libretech-CC (GXL) & S400 (AXG), with Device mode added and tested by using the UMS gadget. Neil Armstrong (8): ARM: dts: sync amlogic AXG/GXL/GXM DT from Linux 5.8-rc1 usb: dwc3: add Amlogic GXL & GXL DWC3 Glue ARM: mach-meson: use new DWC3 glue for GXL & GXM phy: meson-gxl: remove invalid USB3 PHY driver phy: meson-gxl-usb: depend on Meson AXG aswell arm: meson-axg: add board_usb_init()/cleanup() for USB gadget ARM: dts: meson-axg: add USB nodes for S400 configs: s400: enable USB arch/arm/dts/meson-axg-s400-u-boot.dtsi | 12 + arch/arm/dts/meson-axg-u-boot.dtsi | 62 +++ arch/arm/dts/meson-axg.dtsi | 6 +- arch/arm/dts/meson-gx-libretech-pc.dtsi | 78 +++- arch/arm/dts/meson-gx.dtsi | 23 +- arch/arm/dts/meson-gxbb-nanopi-k2.dts | 2 +- arch/arm/dts/meson-gxbb-odroidc2.dts | 2 +- arch/arm/dts/meson-gxbb.dtsi | 23 + .../meson-gxl-s805x-libretech-ac-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 73 ++- .../meson-gxl-s905d-libretech-pc-u-boot.dtsi | 4 - .../meson-gxl-s905x-khadas-vim-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 4 + .../meson-gxl-s905x-libretech-cc-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s905x-libretech-cc.dts | 77 +++- arch/arm/dts/meson-gxl-s905x-p212.dtsi | 3 +- arch/arm/dts/meson-gxl-u-boot.dtsi | 16 - arch/arm/dts/meson-gxl.dtsi | 79 +++- .../arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi | 4 - arch/arm/dts/meson-gxm-khadas-vim2.dts | 3 +- .../meson-gxm-s912-libretech-pc-u-boot.dtsi | 4 - arch/arm/dts/meson-gxm.dtsi | 7 +- arch/arm/include/asm/arch-meson/usb-gx.h | 3 +- arch/arm/mach-meson/board-axg.c | 128 ++++++ arch/arm/mach-meson/board-gx.c | 127 +++--- configs/khadas-vim2_defconfig | 2 +- configs/khadas-vim_defconfig | 2 +- configs/libretech-ac_defconfig | 2 +- configs/libretech-cc_defconfig | 2 +- configs/libretech-s905d-pc_defconfig | 2 +- configs/libretech-s912-pc_defconfig | 2 +- configs/p212_defconfig | 2 +- configs/s400_defconfig | 15 + drivers/phy/Kconfig | 2 +- drivers/phy/Makefile | 2 +- drivers/phy/meson-gxl-usb3.c | 219 --------- drivers/usb/dwc3/Kconfig | 8 + drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-meson-gxl.c | 425 ++++++++++++++++++ .../reset/amlogic,meson-gxbb-reset.h | 2 +- include/dt-bindings/sound/meson-aiu.h | 18 + 41 files changed, 1092 insertions(+), 366 deletions(-) create mode 100644 arch/arm/dts/meson-axg-u-boot.dtsi delete mode 100644 drivers/phy/meson-gxl-usb3.c create mode 100644 drivers/usb/dwc3/dwc3-meson-gxl.c create mode 100644 include/dt-bindings/sound/meson-aiu.h -- 2.22.0
WARNING: multiple messages have this Message-ID (diff)
From: "Neil Armstrong" <narmstrong@baylibre.com> To: marex@denx.de Cc: u-boot-amlogic@groups.io, u-boot@lists.denx.de, Neil Armstrong <narmstrong@baylibre.com> Subject: [PATCH 0/8] ARM: mach-meson: update & rework USB for GXL, GXM & AXG Date: Thu, 10 Sep 2020 10:48:11 +0200 [thread overview] Message-ID: <20200910084819.25312-1-narmstrong@baylibre.com> (raw) This serie follows the recent work under Linux to rework and update support of the USB complex in the Amlogic GXL, GXM & AXG SoCs. This rework follows the clean implementation for the G12A & following SoCs to support Host, Device & OTG functionnality. The GXL, GXM & AXG USB complex is architectured in the same was as the G12A & later USB complex, thus we can use the same architecture but adapted to the different init & config flow found in the Amlogic GXL, GXM & AXG SoCs. With this patchset, USB Host functionnality is retained, working & tested on the Khadas VIM2 (GXM), Libretech-CC (GXL) & S400 (AXG), with Device mode added and tested by using the UMS gadget. Neil Armstrong (8): ARM: dts: sync amlogic AXG/GXL/GXM DT from Linux 5.8-rc1 usb: dwc3: add Amlogic GXL & GXL DWC3 Glue ARM: mach-meson: use new DWC3 glue for GXL & GXM phy: meson-gxl: remove invalid USB3 PHY driver phy: meson-gxl-usb: depend on Meson AXG aswell arm: meson-axg: add board_usb_init()/cleanup() for USB gadget ARM: dts: meson-axg: add USB nodes for S400 configs: s400: enable USB arch/arm/dts/meson-axg-s400-u-boot.dtsi | 12 + arch/arm/dts/meson-axg-u-boot.dtsi | 62 +++ arch/arm/dts/meson-axg.dtsi | 6 +- arch/arm/dts/meson-gx-libretech-pc.dtsi | 78 +++- arch/arm/dts/meson-gx.dtsi | 23 +- arch/arm/dts/meson-gxbb-nanopi-k2.dts | 2 +- arch/arm/dts/meson-gxbb-odroidc2.dts | 2 +- arch/arm/dts/meson-gxbb.dtsi | 23 + .../meson-gxl-s805x-libretech-ac-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 73 ++- .../meson-gxl-s905d-libretech-pc-u-boot.dtsi | 4 - .../meson-gxl-s905x-khadas-vim-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 4 + .../meson-gxl-s905x-libretech-cc-u-boot.dtsi | 4 - arch/arm/dts/meson-gxl-s905x-libretech-cc.dts | 77 +++- arch/arm/dts/meson-gxl-s905x-p212.dtsi | 3 +- arch/arm/dts/meson-gxl-u-boot.dtsi | 16 - arch/arm/dts/meson-gxl.dtsi | 79 +++- .../arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi | 4 - arch/arm/dts/meson-gxm-khadas-vim2.dts | 3 +- .../meson-gxm-s912-libretech-pc-u-boot.dtsi | 4 - arch/arm/dts/meson-gxm.dtsi | 7 +- arch/arm/include/asm/arch-meson/usb-gx.h | 3 +- arch/arm/mach-meson/board-axg.c | 128 ++++++ arch/arm/mach-meson/board-gx.c | 127 +++--- configs/khadas-vim2_defconfig | 2 +- configs/khadas-vim_defconfig | 2 +- configs/libretech-ac_defconfig | 2 +- configs/libretech-cc_defconfig | 2 +- configs/libretech-s905d-pc_defconfig | 2 +- configs/libretech-s912-pc_defconfig | 2 +- configs/p212_defconfig | 2 +- configs/s400_defconfig | 15 + drivers/phy/Kconfig | 2 +- drivers/phy/Makefile | 2 +- drivers/phy/meson-gxl-usb3.c | 219 --------- drivers/usb/dwc3/Kconfig | 8 + drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-meson-gxl.c | 425 ++++++++++++++++++ .../reset/amlogic,meson-gxbb-reset.h | 2 +- include/dt-bindings/sound/meson-aiu.h | 18 + 41 files changed, 1092 insertions(+), 366 deletions(-) create mode 100644 arch/arm/dts/meson-axg-u-boot.dtsi delete mode 100644 drivers/phy/meson-gxl-usb3.c create mode 100644 drivers/usb/dwc3/dwc3-meson-gxl.c create mode 100644 include/dt-bindings/sound/meson-aiu.h -- 2.22.0
next reply other threads:[~2020-09-10 8:48 UTC|newest] Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-09-10 8:48 Neil Armstrong [this message] 2020-09-10 8:48 ` [PATCH 0/8] ARM: mach-meson: update & rework USB for GXL, GXM & AXG Neil Armstrong 2020-09-10 8:48 ` [PATCH 1/8] ARM: dts: sync amlogic AXG/GXL/GXM DT from Linux 5.8-rc1 Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 2/8] usb: dwc3: add Amlogic GXL & GXL DWC3 Glue Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 3/8] ARM: mach-meson: use new DWC3 glue for GXL & GXM Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 4/8] phy: meson-gxl: remove invalid USB3 PHY driver Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 5/8] phy: meson-gxl-usb: depend on Meson AXG aswell Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 6/8] arm: meson-axg: add board_usb_init()/cleanup() for USB gadget Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 7/8] ARM: dts: meson-axg: add USB nodes for S400 Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-10 8:48 ` [PATCH 8/8] configs: s400: enable USB Neil Armstrong 2020-09-10 8:48 ` Neil Armstrong 2020-09-28 7:41 ` [PATCH 0/8] ARM: mach-meson: update & rework USB for GXL, GXM & AXG Neil Armstrong 2020-09-28 7:41 ` Neil Armstrong
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200910084819.25312-1-narmstrong@baylibre.com \ --to=narmstrong@baylibre.com \ --cc=u-boot@lists.denx.de \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.