* hwmon: nct6775: If an ACPI driver is available for this device, you should use it instead of the native driver
@ 2020-10-05 7:50 Corentin Labbe
2020-10-05 15:03 ` Guenter Roeck
0 siblings, 1 reply; 2+ messages in thread
From: Corentin Labbe @ 2020-10-05 7:50 UTC (permalink / raw)
To: linux-hwmon, linux, jdelvare
Hello
I have a motherboard with a nct6775 and I got this on boot:
nct6775: Found NCT6798D or compatible chip at 0x2e:0x290
ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\AMW0.SHWM) (20200326/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
And so the driver is not loaded.
Since I dont have an ACPI driver for it I have hacked the driver to skip this acpi_check_resource_conflict() and the driver works well:
nct6798-isa-0290
Adapter: ISA adapter
in0: 936.00 mV (min = +0.00 V, max = +1.74 V)
in1: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
in2: 3.41 V (min = +0.00 V, max = +0.00 V) ALARM
in3: 3.33 V (min = +0.00 V, max = +0.00 V) ALARM
in4: 1.01 V (min = +0.00 V, max = +0.00 V) ALARM
in5: 776.00 mV (min = +0.00 V, max = +0.00 V) ALARM
in6: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
in7: 3.41 V (min = +0.00 V, max = +0.00 V) ALARM
in8: 3.31 V (min = +0.00 V, max = +0.00 V) ALARM
in9: 904.00 mV (min = +0.00 V, max = +0.00 V) ALARM
in10: 272.00 mV (min = +0.00 V, max = +0.00 V) ALARM
in11: 552.00 mV (min = +0.00 V, max = +0.00 V) ALARM
in12: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
in13: 1.01 V (min = +0.00 V, max = +0.00 V) ALARM
in14: 992.00 mV (min = +0.00 V, max = +0.00 V) ALARM
fan1: 0 RPM (min = 0 RPM)
fan2: 1138 RPM (min = 0 RPM)
fan3: 1744 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
fan5: 2402 RPM (min = 0 RPM)
fan6: 0 RPM (min = 0 RPM)
fan7: 0 RPM (min = 0 RPM)
SYSTIN: +38.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor
CPUTIN: +37.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor
AUXTIN0: +25.0°C sensor = thermistor
AUXTIN1: +53.0°C sensor = thermistor
AUXTIN2: +20.0°C sensor = thermistor
AUXTIN3: +26.0°C sensor = thermistor
SMBUSMASTER 1: +61.5°C
PCH_CHIP_CPU_MAX_TEMP: +0.0°C
PCH_CHIP_TEMP: +0.0°C
PCH_CPU_TEMP: +0.0°C
intrusion0: ALARM
intrusion1: ALARM
beep_enable: disabled
I got the same problem with an it87 and did the same, but does it exists a better way to do this ?
Or does I ignore soemthing to make it works ?
Thanks
Regards
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: hwmon: nct6775: If an ACPI driver is available for this device, you should use it instead of the native driver
2020-10-05 7:50 hwmon: nct6775: If an ACPI driver is available for this device, you should use it instead of the native driver Corentin Labbe
@ 2020-10-05 15:03 ` Guenter Roeck
0 siblings, 0 replies; 2+ messages in thread
From: Guenter Roeck @ 2020-10-05 15:03 UTC (permalink / raw)
To: Corentin Labbe, linux-hwmon, jdelvare
On 10/5/20 12:50 AM, Corentin Labbe wrote:
> Hello
>
> I have a motherboard with a nct6775 and I got this on boot:
> nct6775: Found NCT6798D or compatible chip at 0x2e:0x290
> ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\AMW0.SHWM) (20200326/utaddress-204)
> ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
> And so the driver is not loaded.
>
> Since I dont have an ACPI driver for it I have hacked the driver to skip this acpi_check_resource_conflict() and the driver works well:
> nct6798-isa-0290
> Adapter: ISA adapter
> in0: 936.00 mV (min = +0.00 V, max = +1.74 V)
> in1: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
> in2: 3.41 V (min = +0.00 V, max = +0.00 V) ALARM
> in3: 3.33 V (min = +0.00 V, max = +0.00 V) ALARM
> in4: 1.01 V (min = +0.00 V, max = +0.00 V) ALARM
> in5: 776.00 mV (min = +0.00 V, max = +0.00 V) ALARM
> in6: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
> in7: 3.41 V (min = +0.00 V, max = +0.00 V) ALARM
> in8: 3.31 V (min = +0.00 V, max = +0.00 V) ALARM
> in9: 904.00 mV (min = +0.00 V, max = +0.00 V) ALARM
> in10: 272.00 mV (min = +0.00 V, max = +0.00 V) ALARM
> in11: 552.00 mV (min = +0.00 V, max = +0.00 V) ALARM
> in12: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM
> in13: 1.01 V (min = +0.00 V, max = +0.00 V) ALARM
> in14: 992.00 mV (min = +0.00 V, max = +0.00 V) ALARM
> fan1: 0 RPM (min = 0 RPM)
> fan2: 1138 RPM (min = 0 RPM)
> fan3: 1744 RPM (min = 0 RPM)
> fan4: 0 RPM (min = 0 RPM)
> fan5: 2402 RPM (min = 0 RPM)
> fan6: 0 RPM (min = 0 RPM)
> fan7: 0 RPM (min = 0 RPM)
> SYSTIN: +38.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor
> CPUTIN: +37.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor
> AUXTIN0: +25.0°C sensor = thermistor
> AUXTIN1: +53.0°C sensor = thermistor
> AUXTIN2: +20.0°C sensor = thermistor
> AUXTIN3: +26.0°C sensor = thermistor
> SMBUSMASTER 1: +61.5°C
> PCH_CHIP_CPU_MAX_TEMP: +0.0°C
> PCH_CHIP_TEMP: +0.0°C
> PCH_CPU_TEMP: +0.0°C
> intrusion0: ALARM
> intrusion1: ALARM
> beep_enable: disabled
>
> I got the same problem with an it87 and did the same, but does it exists a better way to do this ?
> Or does I ignore soemthing to make it works ?
>
You could add "acpi_enforce_resources=lax" to the kernel command line.
Your hack (and the command line parameter) may be problematic
if ACPI does indeed access the chip since the chip has multiple pages
and ACPI may (unsynchronized with the kernel driver) change the page
number.
Worst case this may cause a system hang or reboot, unfortunately.
You might at least want to decode the ACPI tables to determine what,
if anything, it does when accessing the chip. You might be lucky
and it doesn't really access it - some systems just reserve the address
space but don't use it, presumably because system vendors don't want
users to access the SuperIO chip directly.
Guenter
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2020-10-05 15:03 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-05 7:50 hwmon: nct6775: If an ACPI driver is available for this device, you should use it instead of the native driver Corentin Labbe
2020-10-05 15:03 ` Guenter Roeck
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.