* [PATCH] hw/block: m25p80: Implement AAI-WP command support for SST flashes
@ 2020-12-02 14:30 Bin Meng
2020-12-03 12:54 ` Francisco Iglesias
0 siblings, 1 reply; 3+ messages in thread
From: Bin Meng @ 2020-12-02 14:30 UTC (permalink / raw)
To: Alistair Francis, Kevin Wolf, Max Reitz, qemu-block, qemu-devel
Cc: Xuzhou Cheng, Bin Meng
From: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Auto Address Increment (AAI) Word-Program is a special command of
SST flashes. AAI-WP allows multiple bytes of data to be programmed
without re-issuing the next sequential address location.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
---
hw/block/m25p80.c | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
index 9b36762df9..f225d9c96d 100644
--- a/hw/block/m25p80.c
+++ b/hw/block/m25p80.c
@@ -359,6 +359,7 @@ typedef enum {
QPP_4 = 0x34,
RDID_90 = 0x90,
RDID_AB = 0xab,
+ AAI_WP = 0xad,
ERASE_4K = 0x20,
ERASE4_4K = 0x21,
@@ -449,6 +450,7 @@ struct Flash {
bool four_bytes_address_mode;
bool reset_enable;
bool quad_enable;
+ bool aai_enable;
uint8_t ear;
int64_t dirty_page;
@@ -661,6 +663,7 @@ static void complete_collecting_data(Flash *s)
case PP:
case PP4:
case PP4_4:
+ case AAI_WP:
s->state = STATE_PAGE_PROGRAM;
break;
case READ:
@@ -1010,6 +1013,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case WRDI:
s->write_enable = false;
+ if (get_man(s) == MAN_SST) {
+ s->aai_enable = false;
+ }
break;
case WREN:
s->write_enable = true;
@@ -1162,6 +1168,17 @@ static void decode_new_cmd(Flash *s, uint32_t value)
case RSTQIO:
s->quad_enable = false;
break;
+ case AAI_WP:
+ if (get_man(s) == MAN_SST && s->write_enable) {
+ if (s->aai_enable) {
+ s->state = STATE_PAGE_PROGRAM;
+ } else {
+ s->aai_enable = true;
+ s->needed_bytes = get_addr_length(s);
+ s->state = STATE_COLLECTING_DATA;
+ }
+ }
+ break;
default:
s->pos = 0;
s->len = 1;
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] hw/block: m25p80: Implement AAI-WP command support for SST flashes
2020-12-02 14:30 [PATCH] hw/block: m25p80: Implement AAI-WP command support for SST flashes Bin Meng
@ 2020-12-03 12:54 ` Francisco Iglesias
2020-12-11 6:13 ` Bin Meng
0 siblings, 1 reply; 3+ messages in thread
From: Francisco Iglesias @ 2020-12-03 12:54 UTC (permalink / raw)
To: Bin Meng
Cc: Kevin Wolf, Bin Meng, qemu-block, Xuzhou Cheng, Alistair Francis,
qemu-devel, Max Reitz
Hello Bin,
On [2020 Dec 02] Wed 22:30:37, Bin Meng wrote:
> From: Xuzhou Cheng <xuzhou.cheng@windriver.com>
>
> Auto Address Increment (AAI) Word-Program is a special command of
> SST flashes. AAI-WP allows multiple bytes of data to be programmed
> without re-issuing the next sequential address location.
>
> Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
> Signed-off-by: Bin Meng <bin.meng@windriver.com>
> ---
>
> hw/block/m25p80.c | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
> diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> index 9b36762df9..f225d9c96d 100644
> --- a/hw/block/m25p80.c
> +++ b/hw/block/m25p80.c
> @@ -359,6 +359,7 @@ typedef enum {
> QPP_4 = 0x34,
> RDID_90 = 0x90,
> RDID_AB = 0xab,
> + AAI_WP = 0xad,
>
> ERASE_4K = 0x20,
> ERASE4_4K = 0x21,
> @@ -449,6 +450,7 @@ struct Flash {
> bool four_bytes_address_mode;
> bool reset_enable;
> bool quad_enable;
> + bool aai_enable;
We need to add above addition also into the vmstate.
> uint8_t ear;
>
> int64_t dirty_page;
> @@ -661,6 +663,7 @@ static void complete_collecting_data(Flash *s)
> case PP:
> case PP4:
> case PP4_4:
> + case AAI_WP:
> s->state = STATE_PAGE_PROGRAM;
> break;
> case READ:
> @@ -1010,6 +1013,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
Since only 3 cmds are allowed while within AAI programming sequence [1] I think
a warning migt be good have before the command switch case, similar to:
if (get_man(s) == MAN_SST && s->aai_enable && !is_valid_aai_cmd(value)) {
qemu_log_mask(LOG_GUEST_ERROR,
"M25P80: Invalid cmd within AAI programming sequence");
}
>
> case WRDI:
> s->write_enable = false;
> + if (get_man(s) == MAN_SST) {
> + s->aai_enable = false;
> + }
> break;
> case WREN:
> s->write_enable = true;
> @@ -1162,6 +1168,17 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> case RSTQIO:
> s->quad_enable = false;
> break;
> + case AAI_WP:
> + if (get_man(s) == MAN_SST && s->write_enable) {
> + if (s->aai_enable) {
> + s->state = STATE_PAGE_PROGRAM;
> + } else {
> + s->aai_enable = true;
> + s->needed_bytes = get_addr_length(s);
> + s->state = STATE_COLLECTING_DATA;
> + }
Perhaps a qemu_log_mask in an 'else' could be useful here also:
} else {
qemu_log_mask(LOG_GUEST_ERROR, "M25P80: %s"
(get_man(s) == MAN_SST) ? "AAI_WP with write protect" :
"Unknown CMD: 0xAD\n");
Lastly, [1] also says that the address shouldn't wrapp around when in AAI mode,
so we need a check before doing that also I think.
Best regards,
Francisco Iglesias
[1] http://ww1.microchip.com/downloads/en/devicedoc/s71271_04.pdf
> + }
> + break;
> default:
> s->pos = 0;
> s->len = 1;
> --
> 2.25.1
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] hw/block: m25p80: Implement AAI-WP command support for SST flashes
2020-12-03 12:54 ` Francisco Iglesias
@ 2020-12-11 6:13 ` Bin Meng
0 siblings, 0 replies; 3+ messages in thread
From: Bin Meng @ 2020-12-11 6:13 UTC (permalink / raw)
To: Francisco Iglesias
Cc: Kevin Wolf, Bin Meng, Qemu-block, Xuzhou Cheng, Alistair Francis,
qemu-devel@nongnu.org Developers, Max Reitz
Hi Francisco,
On Thu, Dec 3, 2020 at 8:54 PM Francisco Iglesias
<frasse.iglesias@gmail.com> wrote:
>
> Hello Bin,
>
> On [2020 Dec 02] Wed 22:30:37, Bin Meng wrote:
> > From: Xuzhou Cheng <xuzhou.cheng@windriver.com>
> >
> > Auto Address Increment (AAI) Word-Program is a special command of
> > SST flashes. AAI-WP allows multiple bytes of data to be programmed
> > without re-issuing the next sequential address location.
> >
> > Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
> > Signed-off-by: Bin Meng <bin.meng@windriver.com>
> > ---
> >
> > hw/block/m25p80.c | 17 +++++++++++++++++
> > 1 file changed, 17 insertions(+)
> >
> > diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> > index 9b36762df9..f225d9c96d 100644
> > --- a/hw/block/m25p80.c
> > +++ b/hw/block/m25p80.c
> > @@ -359,6 +359,7 @@ typedef enum {
> > QPP_4 = 0x34,
> > RDID_90 = 0x90,
> > RDID_AB = 0xab,
> > + AAI_WP = 0xad,
> >
> > ERASE_4K = 0x20,
> > ERASE4_4K = 0x21,
> > @@ -449,6 +450,7 @@ struct Flash {
> > bool four_bytes_address_mode;
> > bool reset_enable;
> > bool quad_enable;
> > + bool aai_enable;
>
> We need to add above addition also into the vmstate.
>
> > uint8_t ear;
> >
> > int64_t dirty_page;
> > @@ -661,6 +663,7 @@ static void complete_collecting_data(Flash *s)
> > case PP:
> > case PP4:
> > case PP4_4:
> > + case AAI_WP:
> > s->state = STATE_PAGE_PROGRAM;
> > break;
> > case READ:
> > @@ -1010,6 +1013,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>
> Since only 3 cmds are allowed while within AAI programming sequence [1] I think
> a warning migt be good have before the command switch case, similar to:
>
> if (get_man(s) == MAN_SST && s->aai_enable && !is_valid_aai_cmd(value)) {
> qemu_log_mask(LOG_GUEST_ERROR,
> "M25P80: Invalid cmd within AAI programming sequence");
> }
>
> >
> > case WRDI:
> > s->write_enable = false;
> > + if (get_man(s) == MAN_SST) {
> > + s->aai_enable = false;
> > + }
> > break;
> > case WREN:
> > s->write_enable = true;
> > @@ -1162,6 +1168,17 @@ static void decode_new_cmd(Flash *s, uint32_t value)
> > case RSTQIO:
> > s->quad_enable = false;
> > break;
> > + case AAI_WP:
> > + if (get_man(s) == MAN_SST && s->write_enable) {
> > + if (s->aai_enable) {
> > + s->state = STATE_PAGE_PROGRAM;
> > + } else {
> > + s->aai_enable = true;
> > + s->needed_bytes = get_addr_length(s);
> > + s->state = STATE_COLLECTING_DATA;
> > + }
>
> Perhaps a qemu_log_mask in an 'else' could be useful here also:
>
> } else {
> qemu_log_mask(LOG_GUEST_ERROR, "M25P80: %s"
> (get_man(s) == MAN_SST) ? "AAI_WP with write protect" :
> "Unknown CMD: 0xAD\n");
>
> Lastly, [1] also says that the address shouldn't wrapp around when in AAI mode,
> so we need a check before doing that also I think.
>
> Best regards,
> Francisco Iglesias
>
> [1] http://ww1.microchip.com/downloads/en/devicedoc/s71271_04.pdf
Thanks for the review. All of your comments will be addressed in v2.
Regards,
Bin
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-12-11 6:15 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-02 14:30 [PATCH] hw/block: m25p80: Implement AAI-WP command support for SST flashes Bin Meng
2020-12-03 12:54 ` Francisco Iglesias
2020-12-11 6:13 ` Bin Meng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.