* [PATCH v4 1/3] dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support
@ 2020-12-07 9:00 ` Troy Lee
0 siblings, 0 replies; 12+ messages in thread
From: Troy Lee @ 2020-12-07 9:00 UTC (permalink / raw)
To: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, troy_lee, ryan_chen
Adding Aspeed AST2400 and AST2600 binding for edac driver.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Acked-by: Joel Stanley <joel@jms.id.au>
---
.../devicetree/bindings/edac/aspeed-sdram-edac.txt | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
index 6a0f3d90d682..8ca9e0a049d8 100644
--- a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
+++ b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt
@@ -1,6 +1,6 @@
-Aspeed AST2500 SoC EDAC node
+Aspeed BMC SoC EDAC node
-The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error
+The Aspeed BMC SoC supports DDR3 and DDR4 memory with and without ECC (error
correction check).
The memory controller supports SECDED (single bit error correction, double bit
@@ -11,7 +11,10 @@ Note, the bootloader must configure ECC mode in the memory controller.
Required properties:
-- compatible: should be "aspeed,ast2500-sdram-edac"
+- compatible: should be one of
+ - "aspeed,ast2400-sdram-edac"
+ - "aspeed,ast2500-sdram-edac"
+ - "aspeed,ast2600-sdram-edac"
- reg: sdram controller register set should be <0x1e6e0000 0x174>
- interrupts: should be AVIC interrupt #0
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 2/3] ARM: dts: aspeed: Add AST2600 edac into common devicetree
2020-12-07 9:00 ` Troy Lee
@ 2020-12-07 9:00 ` Troy Lee
-1 siblings, 0 replies; 12+ messages in thread
From: Troy Lee @ 2020-12-07 9:00 UTC (permalink / raw)
To: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, troy_lee, ryan_chen
Adding Aspeed AST2600 edac node into common devicetree.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
---
arch/arm/boot/dts/aspeed-g6.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index b58220a49cbd..74367ee96f20 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -69,6 +69,12 @@
always-on;
};
+ edac: sdram@1e6e0000 {
+ compatible = "aspeed,ast2600-sdram-edac", "syscon";
+ reg = <0x1e6e0000 0x174>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
ahb {
compatible = "simple-bus";
#address-cells = <1>;
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v4 2/3] ARM: dts: aspeed: Add AST2600 edac into common devicetree
@ 2020-12-07 9:00 ` Troy Lee
0 siblings, 0 replies; 12+ messages in thread
From: Troy Lee @ 2020-12-07 9:00 UTC (permalink / raw)
To: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, troy_lee, ryan_chen
Adding Aspeed AST2600 edac node into common devicetree.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
---
arch/arm/boot/dts/aspeed-g6.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index b58220a49cbd..74367ee96f20 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -69,6 +69,12 @@
always-on;
};
+ edac: sdram@1e6e0000 {
+ compatible = "aspeed,ast2600-sdram-edac", "syscon";
+ reg = <0x1e6e0000 0x174>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
ahb {
compatible = "simple-bus";
#address-cells = <1>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
2020-12-07 9:00 ` Troy Lee
@ 2020-12-07 9:00 ` Troy Lee
-1 siblings, 0 replies; 12+ messages in thread
From: Troy Lee @ 2020-12-07 9:00 UTC (permalink / raw)
To: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, troy_lee, ryan_chen
Adding AST2400 and AST2600 edac driver support.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
---
drivers/edac/Kconfig | 6 +++---
drivers/edac/aspeed_edac.c | 7 +++++--
2 files changed, 8 insertions(+), 5 deletions(-)
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 7a47680d6f07..c410331e8ee8 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -515,10 +515,10 @@ config EDAC_QCOM
health, you should probably say 'Y' here.
config EDAC_ASPEED
- tristate "Aspeed AST 2500 SoC"
- depends on MACH_ASPEED_G5
+ tristate "Aspeed AST BMC SoC"
+ depends on ARCH_ASPEED
help
- Support for error detection and correction on the Aspeed AST 2500 SoC.
+ Support for error detection and correction on the Aspeed AST BMC SoC.
First, ECC must be configured in the bootloader. Then, this driver
will expose error counters via the EDAC kernel framework.
diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
index fde809efc520..a46da56d6d54 100644
--- a/drivers/edac/aspeed_edac.c
+++ b/drivers/edac/aspeed_edac.c
@@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
int rc;
/* retrieve info about physical memory from device tree */
- np = of_find_node_by_path("/memory");
+ np = of_find_node_by_name(NULL, "memory");
if (!np) {
dev_err(mci->pdev, "dt: missing /memory node\n");
return -ENODEV;
@@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
static const struct of_device_id aspeed_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdram-edac" },
{ .compatible = "aspeed,ast2500-sdram-edac" },
+ { .compatible = "aspeed,ast2600-sdram-edac" },
{},
};
+MODULE_DEVICE_TABLE(of, aspeed_of_match);
static struct platform_driver aspeed_driver = {
.driver = {
@@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Stefan Schaeckeler <sschaeck@cisco.com>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
MODULE_VERSION("1.0");
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
@ 2020-12-07 9:00 ` Troy Lee
0 siblings, 0 replies; 12+ messages in thread
From: Troy Lee @ 2020-12-07 9:00 UTC (permalink / raw)
To: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, troy_lee, ryan_chen
Adding AST2400 and AST2600 edac driver support.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
---
drivers/edac/Kconfig | 6 +++---
drivers/edac/aspeed_edac.c | 7 +++++--
2 files changed, 8 insertions(+), 5 deletions(-)
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 7a47680d6f07..c410331e8ee8 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -515,10 +515,10 @@ config EDAC_QCOM
health, you should probably say 'Y' here.
config EDAC_ASPEED
- tristate "Aspeed AST 2500 SoC"
- depends on MACH_ASPEED_G5
+ tristate "Aspeed AST BMC SoC"
+ depends on ARCH_ASPEED
help
- Support for error detection and correction on the Aspeed AST 2500 SoC.
+ Support for error detection and correction on the Aspeed AST BMC SoC.
First, ECC must be configured in the bootloader. Then, this driver
will expose error counters via the EDAC kernel framework.
diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
index fde809efc520..a46da56d6d54 100644
--- a/drivers/edac/aspeed_edac.c
+++ b/drivers/edac/aspeed_edac.c
@@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
int rc;
/* retrieve info about physical memory from device tree */
- np = of_find_node_by_path("/memory");
+ np = of_find_node_by_name(NULL, "memory");
if (!np) {
dev_err(mci->pdev, "dt: missing /memory node\n");
return -ENODEV;
@@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
static const struct of_device_id aspeed_of_match[] = {
+ { .compatible = "aspeed,ast2400-sdram-edac" },
{ .compatible = "aspeed,ast2500-sdram-edac" },
+ { .compatible = "aspeed,ast2600-sdram-edac" },
{},
};
+MODULE_DEVICE_TABLE(of, aspeed_of_match);
static struct platform_driver aspeed_driver = {
.driver = {
@@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Stefan Schaeckeler <sschaeck@cisco.com>");
-MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
+MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
MODULE_VERSION("1.0");
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
2020-12-07 9:00 ` Troy Lee
@ 2020-12-07 9:10 ` Stefan Schaeckeler (sschaeck)
-1 siblings, 0 replies; 12+ messages in thread
From: Stefan Schaeckeler (sschaeck) @ 2020-12-07 9:10 UTC (permalink / raw)
To: Troy Lee, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, ryan_chen
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com>
> ---
drivers/edac/Kconfig | 6 +++---
> drivers/edac/aspeed_edac.c | 7 +++++--
> 2 files changed, 8 insertions(+), 5 deletions(-)
> diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
> index 7a47680d6f07..c410331e8ee8 100644
> --- a/drivers/edac/Kconfig
> +++ b/drivers/edac/Kconfig
> @@ -515,10 +515,10 @@ config EDAC_QCOM
> health, you should probably say 'Y' here.
>
> config EDAC_ASPEED
> - tristate "Aspeed AST 2500 SoC"
> - depends on MACH_ASPEED_G5
> + tristate "Aspeed AST BMC SoC"
> + depends on ARCH_ASPEED
> help
> - Support for error detection and correction on the Aspeed AST 2500 SoC.
> + Support for error detection and correction on the Aspeed AST BMC SoC.
>
> First, ECC must be configured in the bootloader. Then, this driver
> will expose error counters via the EDAC kernel framework.
> diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
> index fde809efc520..a46da56d6d54 100644
> --- a/drivers/edac/aspeed_edac.c
> +++ b/drivers/edac/aspeed_edac.c
> @@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
> int rc;
>
> /* retrieve info about physical memory from device tree */
> - np = of_find_node_by_path("/memory");
> + np = of_find_node_by_name(NULL, "memory");
> if (!np) {
> dev_err(mci->pdev, "dt: missing /memory node\n");
> return -ENODEV;
> @@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
>
>
> static const struct of_device_id aspeed_of_match[] = {
> + { .compatible = "aspeed,ast2400-sdram-edac" },
> { .compatible = "aspeed,ast2500-sdram-edac" },
> + { .compatible = "aspeed,ast2600-sdram-edac" },
> {},
> };
>
> +MODULE_DEVICE_TABLE(of, aspeed_of_match);
>
> static struct platform_driver aspeed_driver = {
> .driver = {
> @@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
>
> MODULE_LICENSE("GPL");
> MODULE_AUTHOR("Stefan Schaeckeler <sschaeck@cisco.com>");
> -MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
> +MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
> MODULE_VERSION("1.0");
> --
> 2.17.1
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
@ 2020-12-07 9:10 ` Stefan Schaeckeler (sschaeck)
0 siblings, 0 replies; 12+ messages in thread
From: Stefan Schaeckeler (sschaeck) @ 2020-12-07 9:10 UTC (permalink / raw)
To: Troy Lee, Rob Herring, Joel Stanley, Andrew Jeffery,
Borislav Petkov, Mauro Carvalho Chehab, Tony Luck, James Morse,
Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE
Cc: leetroy, ryan_chen
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com>
> ---
drivers/edac/Kconfig | 6 +++---
> drivers/edac/aspeed_edac.c | 7 +++++--
> 2 files changed, 8 insertions(+), 5 deletions(-)
> diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
> index 7a47680d6f07..c410331e8ee8 100644
> --- a/drivers/edac/Kconfig
> +++ b/drivers/edac/Kconfig
> @@ -515,10 +515,10 @@ config EDAC_QCOM
> health, you should probably say 'Y' here.
>
> config EDAC_ASPEED
> - tristate "Aspeed AST 2500 SoC"
> - depends on MACH_ASPEED_G5
> + tristate "Aspeed AST BMC SoC"
> + depends on ARCH_ASPEED
> help
> - Support for error detection and correction on the Aspeed AST 2500 SoC.
> + Support for error detection and correction on the Aspeed AST BMC SoC.
>
> First, ECC must be configured in the bootloader. Then, this driver
> will expose error counters via the EDAC kernel framework.
> diff --git a/drivers/edac/aspeed_edac.c b/drivers/edac/aspeed_edac.c
> index fde809efc520..a46da56d6d54 100644
> --- a/drivers/edac/aspeed_edac.c
> +++ b/drivers/edac/aspeed_edac.c
> @@ -239,7 +239,7 @@ static int init_csrows(struct mem_ctl_info *mci)
> int rc;
>
> /* retrieve info about physical memory from device tree */
> - np = of_find_node_by_path("/memory");
> + np = of_find_node_by_name(NULL, "memory");
> if (!np) {
> dev_err(mci->pdev, "dt: missing /memory node\n");
> return -ENODEV;
> @@ -375,10 +375,13 @@ static int aspeed_remove(struct platform_device *pdev)
>
>
> static const struct of_device_id aspeed_of_match[] = {
> + { .compatible = "aspeed,ast2400-sdram-edac" },
> { .compatible = "aspeed,ast2500-sdram-edac" },
> + { .compatible = "aspeed,ast2600-sdram-edac" },
> {},
> };
>
> +MODULE_DEVICE_TABLE(of, aspeed_of_match);
>
> static struct platform_driver aspeed_driver = {
> .driver = {
> @@ -392,5 +395,5 @@ module_platform_driver(aspeed_driver);
>
> MODULE_LICENSE("GPL");
> MODULE_AUTHOR("Stefan Schaeckeler <sschaeck@cisco.com>");
> -MODULE_DESCRIPTION("Aspeed AST2500 EDAC driver");
> +MODULE_DESCRIPTION("Aspeed BMC SoC EDAC driver");
> MODULE_VERSION("1.0");
> --
> 2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
2020-12-07 9:00 ` Troy Lee
@ 2020-12-07 11:53 ` Joel Stanley
-1 siblings, 0 replies; 12+ messages in thread
From: Joel Stanley @ 2020-12-07 11:53 UTC (permalink / raw)
To: Troy Lee
Cc: Stefan Schaeckeler, Rob Herring, Andrew Jeffery, Borislav Petkov,
Mauro Carvalho Chehab, Tony Luck, James Morse, Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE, leetroy, Ryan Chen
On Mon, 7 Dec 2020 at 09:01, Troy Lee <troy_lee@aspeedtech.com> wrote:
>
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/3] edac: Supporting AST2400 and AST2600 edac driver
@ 2020-12-07 11:53 ` Joel Stanley
0 siblings, 0 replies; 12+ messages in thread
From: Joel Stanley @ 2020-12-07 11:53 UTC (permalink / raw)
To: Troy Lee
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Tony Luck, Robert Richter, James Morse,
moderated list:ARM/ASPEED MACHINE SUPPORT, Andrew Jeffery,
open list, leetroy, Rob Herring, Borislav Petkov, Ryan Chen,
Stefan Schaeckeler, Mauro Carvalho Chehab,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list:EDAC-CORE
On Mon, 7 Dec 2020 at 09:01, Troy Lee <troy_lee@aspeedtech.com> wrote:
>
> Adding AST2400 and AST2600 edac driver support.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 1/3] dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support
2020-12-07 9:00 ` Troy Lee
@ 2020-12-07 11:11 ` Borislav Petkov
-1 siblings, 0 replies; 12+ messages in thread
From: Borislav Petkov @ 2020-12-07 11:11 UTC (permalink / raw)
To: Troy Lee
Cc: Stefan Schaeckeler, Rob Herring, Joel Stanley, Andrew Jeffery,
Mauro Carvalho Chehab, Tony Luck, James Morse, Robert Richter,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/ASPEED MACHINE SUPPORT,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list,
open list:EDAC-CORE, leetroy, ryan_chen
On Mon, Dec 07, 2020 at 05:00:11PM +0800, Troy Lee wrote:
> Adding Aspeed AST2400 and AST2600 binding for edac driver.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
> Acked-by: Joel Stanley <joel@jms.id.au>
> ---
> .../devicetree/bindings/edac/aspeed-sdram-edac.txt | 9 ++++++---
> 1 file changed, 6 insertions(+), 3 deletions(-)
All 3 applied, thanks.
--
Regards/Gruss,
Boris.
https://people.kernel.org/tglx/notes-about-netiquette
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v4 1/3] dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 support
@ 2020-12-07 11:11 ` Borislav Petkov
0 siblings, 0 replies; 12+ messages in thread
From: Borislav Petkov @ 2020-12-07 11:11 UTC (permalink / raw)
To: Troy Lee
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Tony Luck, Robert Richter,
moderated list:ARM/ASPEED MACHINE SUPPORT, Andrew Jeffery,
ryan_chen, open list, leetroy, Rob Herring, James Morse,
Joel Stanley, Stefan Schaeckeler, Mauro Carvalho Chehab,
moderated list:ARM/ASPEED MACHINE SUPPORT, open list:EDAC-CORE
On Mon, Dec 07, 2020 at 05:00:11PM +0800, Troy Lee wrote:
> Adding Aspeed AST2400 and AST2600 binding for edac driver.
>
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
> Acked-by: Joel Stanley <joel@jms.id.au>
> ---
> .../devicetree/bindings/edac/aspeed-sdram-edac.txt | 9 ++++++---
> 1 file changed, 6 insertions(+), 3 deletions(-)
All 3 applied, thanks.
--
Regards/Gruss,
Boris.
https://people.kernel.org/tglx/notes-about-netiquette
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread