* [PATCH v7 0/8] mainline Plymovent M2M and BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, dri-devel
changes v7:
- panel-simple.yaml: fix comments and part order
- panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
changes v6:
- do more panel-simple.yaml related cleanups
changes v5:
- rebase against latest shawngup/for-next
- add patch to fix checkpatch warning on PLYM2M dts
changes v4:
- add PLYBAS board
- PLYM2M: add touchscreen node
- PLYM2M: add rename led nodes to led-x
changes v3:
- use old style copyright text
changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
Oleksij Rempel (8):
dt-bindings: display: simple: fix alphabetical order for EDT
compatibles
dt-bindings: display: simple: add EDT compatibles already supported by
the driver
dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: arm: fsl: add Plymovent M2M board
ARM: dts: add Plymovent M2M board
dt-bindings: arm: fsl: add Plymovent BAS board
ARM: dts: add Plymovent BAS board
.../devicetree/bindings/arm/fsl.yaml | 2 +
.../bindings/display/panel/panel-simple.yaml | 19 +-
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++
6 files changed, 857 insertions(+), 8 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
--
2.29.2
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v7 0/8] mainline Plymovent M2M and BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
changes v7:
- panel-simple.yaml: fix comments and part order
- panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
changes v6:
- do more panel-simple.yaml related cleanups
changes v5:
- rebase against latest shawngup/for-next
- add patch to fix checkpatch warning on PLYM2M dts
changes v4:
- add PLYBAS board
- PLYM2M: add touchscreen node
- PLYM2M: add rename led nodes to led-x
changes v3:
- use old style copyright text
changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
Oleksij Rempel (8):
dt-bindings: display: simple: fix alphabetical order for EDT
compatibles
dt-bindings: display: simple: add EDT compatibles already supported by
the driver
dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: arm: fsl: add Plymovent M2M board
ARM: dts: add Plymovent M2M board
dt-bindings: arm: fsl: add Plymovent BAS board
ARM: dts: add Plymovent BAS board
.../devicetree/bindings/arm/fsl.yaml | 2 +
.../bindings/display/panel/panel-simple.yaml | 19 +-
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++
6 files changed, 857 insertions(+), 8 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v7 0/8] mainline Plymovent M2M and BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
changes v7:
- panel-simple.yaml: fix comments and part order
- panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
changes v6:
- do more panel-simple.yaml related cleanups
changes v5:
- rebase against latest shawngup/for-next
- add patch to fix checkpatch warning on PLYM2M dts
changes v4:
- add PLYBAS board
- PLYM2M: add touchscreen node
- PLYM2M: add rename led nodes to led-x
changes v3:
- use old style copyright text
changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
Oleksij Rempel (8):
dt-bindings: display: simple: fix alphabetical order for EDT
compatibles
dt-bindings: display: simple: add EDT compatibles already supported by
the driver
dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: arm: fsl: add Plymovent M2M board
ARM: dts: add Plymovent M2M board
dt-bindings: arm: fsl: add Plymovent BAS board
ARM: dts: add Plymovent BAS board
.../devicetree/bindings/arm/fsl.yaml | 2 +
.../bindings/display/panel/panel-simple.yaml | 19 +-
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++
6 files changed, 857 insertions(+), 8 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, dri-devel
Reorder it alphabetically and remove one double entry.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
1 file changed, 6 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index edb53ab0d9eb..7e459ff974dd 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -105,26 +105,24 @@ properties:
- dlc,dlc1010gig
# Emerging Display Technology Corp. 3.5" QVGA TFT LCD panel
- edt,et035012dm6
+ # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
+ - edt,et057090dhu
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
- edt,etm0430g0dh6
- # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- - edt,et057090dhu
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm070080dh6
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm0700g0dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same as ETM0700G0DH6 but with inverted pixel clock.
- edt,etm070080bdh6
+ # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
+ # Same timings as the ETM0700G0DH6, but with resistive touch.
+ - edt,etm070080dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- # Same timings as the ETM0700G0DH6, but with resistive touch.
- - edt,etm070080dh6
+ - edt,etm0700g0dh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Reorder it alphabetically and remove one double entry.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
1 file changed, 6 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index edb53ab0d9eb..7e459ff974dd 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -105,26 +105,24 @@ properties:
- dlc,dlc1010gig
# Emerging Display Technology Corp. 3.5" QVGA TFT LCD panel
- edt,et035012dm6
+ # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
+ - edt,et057090dhu
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
- edt,etm0430g0dh6
- # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- - edt,et057090dhu
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm070080dh6
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm0700g0dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same as ETM0700G0DH6 but with inverted pixel clock.
- edt,etm070080bdh6
+ # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
+ # Same timings as the ETM0700G0DH6, but with resistive touch.
+ - edt,etm070080dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- # Same timings as the ETM0700G0DH6, but with resistive touch.
- - edt,etm070080dh6
+ - edt,etm0700g0dh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Reorder it alphabetically and remove one double entry.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
1 file changed, 6 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index edb53ab0d9eb..7e459ff974dd 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -105,26 +105,24 @@ properties:
- dlc,dlc1010gig
# Emerging Display Technology Corp. 3.5" QVGA TFT LCD panel
- edt,et035012dm6
+ # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
+ - edt,et057090dhu
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
- edt,etm0430g0dh6
- # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- - edt,et057090dhu
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm070080dh6
- # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- - edt,etm0700g0dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same as ETM0700G0DH6 but with inverted pixel clock.
- edt,etm070080bdh6
+ # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
+ # Same timings as the ETM0700G0DH6, but with resistive touch.
+ - edt,etm070080dh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- # Same timings as the ETM0700G0DH6, but with resistive touch.
- - edt,etm070080dh6
+ - edt,etm0700g0dh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, dri-devel
Some EDT compatibles are already supported by the driver but will fail
on checkpatch script. Fix it by syncing dt-bindings documentation with the
driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 7e459ff974dd..46e5b2a5a011 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -107,6 +107,7 @@ properties:
- edt,et035012dm6
# Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- edt,et057090dhu
+ - edt,et070080dh6
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
@@ -121,8 +122,10 @@ properties:
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
+ - edt,etm0700g0bdh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- edt,etm0700g0dh6
+ - edt,etm0700g0edh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Some EDT compatibles are already supported by the driver but will fail
on checkpatch script. Fix it by syncing dt-bindings documentation with the
driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 7e459ff974dd..46e5b2a5a011 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -107,6 +107,7 @@ properties:
- edt,et035012dm6
# Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- edt,et057090dhu
+ - edt,et070080dh6
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
@@ -121,8 +122,10 @@ properties:
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
+ - edt,etm0700g0bdh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- edt,etm0700g0dh6
+ - edt,etm0700g0edh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Some EDT compatibles are already supported by the driver but will fail
on checkpatch script. Fix it by syncing dt-bindings documentation with the
driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 7e459ff974dd..46e5b2a5a011 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -107,6 +107,7 @@ properties:
- edt,et035012dm6
# Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
- edt,et057090dhu
+ - edt,et070080dh6
# Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
- edt,etm043080dh6gp
# Emerging Display Technology Corp. 480x272 TFT Display
@@ -121,8 +122,10 @@ properties:
# Same display as the ETM0700G0BDH6, but with changed hardware for the
# backlight and the touch interface.
- edt,etm070080edh6
+ - edt,etm0700g0bdh6
# Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
- edt,etm0700g0dh6
+ - edt,etm0700g0edh6
# Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
- evervision,vgg804821
# Foxlink Group 5" WVGA TFT LCD panel
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander, dri-devel
So far, this panel seems to be compatible with "lg,lb070wv8", on other
hand it is better to set this compatible in the devicetree. So, let's
add it for now only to the dt-binding documentation to fix the
checkpatch warnings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 46e5b2a5a011..206ff74db53e 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -172,6 +172,8 @@ properties:
- koe,tx26d202vm0bwa
# Kaohsiung Opto-Electronics. TX31D200VM0BAA 12.3" HSXGA LVDS panel
- koe,tx31d200vm0baa
+ # Kyocera Corporation 7" WVGA (800x480) transmissive color TFT
+ - kyo,tcg070wvlq
# Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel
- kyo,tcg121xglp
# LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
So far, this panel seems to be compatible with "lg,lb070wv8", on other
hand it is better to set this compatible in the devicetree. So, let's
add it for now only to the dt-binding documentation to fix the
checkpatch warnings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 46e5b2a5a011..206ff74db53e 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -172,6 +172,8 @@ properties:
- koe,tx26d202vm0bwa
# Kaohsiung Opto-Electronics. TX31D200VM0BAA 12.3" HSXGA LVDS panel
- koe,tx31d200vm0baa
+ # Kyocera Corporation 7" WVGA (800x480) transmissive color TFT
+ - kyo,tcg070wvlq
# Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel
- kyo,tcg121xglp
# LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
So far, this panel seems to be compatible with "lg,lb070wv8", on other
hand it is better to set this compatible in the devicetree. So, let's
add it for now only to the dt-binding documentation to fix the
checkpatch warnings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 46e5b2a5a011..206ff74db53e 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -172,6 +172,8 @@ properties:
- koe,tx26d202vm0bwa
# Kaohsiung Opto-Electronics. TX31D200VM0BAA 12.3" HSXGA LVDS panel
- koe,tx31d200vm0baa
+ # Kyocera Corporation 7" WVGA (800x480) transmissive color TFT
+ - kyo,tcg070wvlq
# Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel
- kyo,tcg121xglp
# LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 4/8] dt-bindings: vendor-prefixes: Add an entry for Plymovent
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Rob Herring, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6a9be2bbbcb6..8332d50301ea 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -840,6 +840,8 @@ patternProperties:
description: PLDA
"^plx,.*":
description: Broadcom Corporation (formerly PLX Technology)
+ "^ply,.*":
+ description: Plymovent Group BV
"^pni,.*":
description: PNI Sensor Corporation
"^pocketbook,.*":
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 4/8] dt-bindings: vendor-prefixes: Add an entry for Plymovent
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Rob Herring, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6a9be2bbbcb6..8332d50301ea 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -840,6 +840,8 @@ patternProperties:
description: PLDA
"^plx,.*":
description: Broadcom Corporation (formerly PLX Technology)
+ "^ply,.*":
+ description: Plymovent Group BV
"^pni,.*":
description: PNI Sensor Corporation
"^pocketbook,.*":
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 4/8] dt-bindings: vendor-prefixes: Add an entry for Plymovent
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6a9be2bbbcb6..8332d50301ea 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -840,6 +840,8 @@ patternProperties:
description: PLDA
"^plx,.*":
description: Broadcom Corporation (formerly PLX Technology)
+ "^ply,.*":
+ description: Plymovent Group BV
"^pni,.*":
description: PNI Sensor Corporation
"^pocketbook,.*":
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 5/8] dt-bindings: arm: fsl: add Plymovent M2M board
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Rob Herring, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add Plymovent Group BV M2M iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 4772f64c4463..36c5a0c5ace2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
- prt,prtvt7 # Protonic VT7 board
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 5/8] dt-bindings: arm: fsl: add Plymovent M2M board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Rob Herring, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Add Plymovent Group BV M2M iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 4772f64c4463..36c5a0c5ace2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
- prt,prtvt7 # Protonic VT7 board
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 5/8] dt-bindings: arm: fsl: add Plymovent M2M board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Add Plymovent Group BV M2M iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 4772f64c4463..36c5a0c5ace2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
- prt,prtvt7 # Protonic VT7 board
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 6/8] ARM: dts: add Plymovent M2M board
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, dri-devel
Plymovent M2M is a control interface produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++++++++++++
2 files changed, 447 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3ab9d58428cf..31249fc5f85c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4d0d3d3386af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent M2M board";
+ compatible = "ply,plym2m", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 1000>;
+ num-interpolated-steps = <20>;
+ default-brightness-level = <19>;
+ power-supply = <®_12v0>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0bdh6";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_12v0: regulator-12v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc2046>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&usbotg {
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x10000
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x3008
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
+ >;
+ };
+
+ pinctrl_tsc2046: tsc2046grp {
+ fsl,pins = <
+ /* TSC_PENIRQ */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ /* TSC_BUSY */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 6/8] ARM: dts: add Plymovent M2M board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Plymovent M2M is a control interface produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++++++++++++
2 files changed, 447 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3ab9d58428cf..31249fc5f85c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4d0d3d3386af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent M2M board";
+ compatible = "ply,plym2m", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 1000>;
+ num-interpolated-steps = <20>;
+ default-brightness-level = <19>;
+ power-supply = <®_12v0>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0bdh6";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_12v0: regulator-12v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc2046>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&usbotg {
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x10000
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x3008
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
+ >;
+ };
+
+ pinctrl_tsc2046: tsc2046grp {
+ fsl,pins = <
+ /* TSC_PENIRQ */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ /* TSC_BUSY */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 6/8] ARM: dts: add Plymovent M2M board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Plymovent M2M is a control interface produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++++++++++++
2 files changed, 447 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3ab9d58428cf..31249fc5f85c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4d0d3d3386af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent M2M board";
+ compatible = "ply,plym2m", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+ brightness-levels = <0 1000>;
+ num-interpolated-steps = <20>;
+ default-brightness-level = <19>;
+ power-supply = <®_12v0>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0bdh6";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_12v0: regulator-12v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ touchscreen@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-0 = <&pinctrl_tsc2046>;
+ pinctrl-names ="default";
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-max-pressure = <4095>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+
+ wakeup-source;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&usbotg {
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ disable-wp;
+ cap-sd-highspeed;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x10000
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x3008
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
+ >;
+ };
+
+ pinctrl_tsc2046: tsc2046grp {
+ fsl,pins = <
+ /* TSC_PENIRQ */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ /* TSC_BUSY */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 7/8] dt-bindings: arm: fsl: add Plymovent BAS board
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, Rob Herring, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
Add Plymovent Group BV BAS iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 36c5a0c5ace2..490cbc75b18a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plybas # Plymovent BAS board
- ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 7/8] dt-bindings: arm: fsl: add Plymovent BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, Rob Herring, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Add Plymovent Group BV BAS iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 36c5a0c5ace2..490cbc75b18a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plybas # Plymovent BAS board
- ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 7/8] dt-bindings: arm: fsl: add Plymovent BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Add Plymovent Group BV BAS iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 36c5a0c5ace2..490cbc75b18a 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -364,6 +364,7 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules
- kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module
+ - ply,plybas # Plymovent BAS board
- ply,plym2m # Plymovent M2M board
- poslab,imx6dl-savageboard # Poslab SavageBoard Dual
- prt,prtrvt # Protonic RVT board
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 8/8] ARM: dts: add Plymovent BAS board
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-07 14:09 ` Oleksij Rempel
-1 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam,
linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, dri-devel
Plymovent BAS is a base system controller produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++
2 files changed, 395 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31249fc5f85c..ee725aebc3a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plybas.dtb \
imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
new file mode 100644
index 000000000000..333c306aa946
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent BAS board";
+ compatible = "ply,plybas", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ button@20 {
+ label = "START";
+ linux,code = <31>;
+ gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+ };
+
+ button@21 {
+ label = "CLEAN";
+ linux,code = <46>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "debug1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "light_tower1";
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-3 {
+ label = "light_tower2";
+ gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "light_tower3";
+ gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ label = "light_tower4";
+ gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+ "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+ "IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+ "IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+ "IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+ "IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+ "IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+ "IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ fsl,uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 20>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG_0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ /* DEBUG_1 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+
+ /* LED1 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
+ /* LED2 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
+ /* LED3 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
+ /* LED4 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 8/8] ARM: dts: add Plymovent BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
Fabio Estevam, linux-arm-kernel
Plymovent BAS is a base system controller produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++
2 files changed, 395 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31249fc5f85c..ee725aebc3a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plybas.dtb \
imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
new file mode 100644
index 000000000000..333c306aa946
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent BAS board";
+ compatible = "ply,plybas", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ button@20 {
+ label = "START";
+ linux,code = <31>;
+ gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+ };
+
+ button@21 {
+ label = "CLEAN";
+ linux,code = <46>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "debug1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "light_tower1";
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-3 {
+ label = "light_tower2";
+ gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "light_tower3";
+ gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ label = "light_tower4";
+ gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+ "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+ "IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+ "IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+ "IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+ "IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+ "IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+ "IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ fsl,uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 20>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG_0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ /* DEBUG_1 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+
+ /* LED1 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
+ /* LED2 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
+ /* LED3 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
+ /* LED4 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* [PATCH v7 8/8] ARM: dts: add Plymovent BAS board
@ 2020-12-07 14:09 ` Oleksij Rempel
0 siblings, 0 replies; 39+ messages in thread
From: Oleksij Rempel @ 2020-12-07 14:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo,
Thierry Reding, Sam Ravnborg, David Airlie, Daniel Vetter
Cc: devicetree, linux-kernel, dri-devel, Oleksij Rempel,
NXP Linux Team, Pengutronix Kernel Team, David Jander,
linux-arm-kernel
Plymovent BAS is a base system controller produced for the Plymovent filter
systems.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++
2 files changed, 395 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31249fc5f85c..ee725aebc3a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -461,6 +461,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
+ imx6dl-plybas.dtb \
imx6dl-plym2m.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
new file mode 100644
index 000000000000..333c306aa946
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+ model = "Plymovent BAS board";
+ compatible = "ply,plybas", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ button@20 {
+ label = "START";
+ linux,code = <31>;
+ gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+ };
+
+ button@21 {
+ label = "CLEAN";
+ linux,code = <46>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-0 {
+ label = "debug0";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "debug1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "light_tower1";
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-3 {
+ label = "light_tower2";
+ gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "light_tower3";
+ gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ label = "light_tower4";
+ gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ clk50m_phy: phy-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ xceiver-supply = <®_5v0>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clk50m_phy>;
+ clock-names = "ipg", "ahb", "ptp";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ8081RNA PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "SD1_CD", "", "", "", "", "", "",
+ "DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+ "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+ "IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+ "IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+ "IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+ "IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+ "IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+ "IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ fsl,uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 20>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphynop1 {
+ status = "disabled";
+};
+
+&usbphynop2 {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
+ /* CAN2_SR */
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG_0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ /* DEBUG_1 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+
+ /* LED1 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
+ /* LED2 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
+ /* LED3 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
+ /* LED4 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+};
--
2.29.2
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 39+ messages in thread
* Re: [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-10 3:45 ` Rob Herring
-1 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:45 UTC (permalink / raw)
To: Oleksij Rempel
Cc: linux-kernel, Thierry Reding, linux-arm-kernel, Daniel Vetter,
dri-devel, Pengutronix Kernel Team, David Jander, Shawn Guo,
Mark Rutland, NXP Linux Team, David Airlie, Rob Herring,
Sascha Hauer, Sam Ravnborg, devicetree
On Mon, 07 Dec 2020 15:09:32 +0100, Oleksij Rempel wrote:
> Reorder it alphabetically and remove one double entry.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
> 1 file changed, 6 insertions(+), 8 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
@ 2020-12-10 3:45 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:45 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Daniel Vetter, David Airlie,
Sam Ravnborg, Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Shawn Guo, linux-arm-kernel
On Mon, 07 Dec 2020 15:09:32 +0100, Oleksij Rempel wrote:
> Reorder it alphabetically and remove one double entry.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
> 1 file changed, 6 insertions(+), 8 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles
@ 2020-12-10 3:45 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:45 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, David Airlie, Sam Ravnborg,
Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, Pengutronix Kernel Team,
David Jander, Shawn Guo, linux-arm-kernel
On Mon, 07 Dec 2020 15:09:32 +0100, Oleksij Rempel wrote:
> Reorder it alphabetically and remove one double entry.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../bindings/display/panel/panel-simple.yaml | 14 ++++++--------
> 1 file changed, 6 insertions(+), 8 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-10 3:46 ` Rob Herring
-1 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Daniel Vetter, linux-kernel, David Jander, devicetree,
David Airlie, dri-devel, Pengutronix Kernel Team, Thierry Reding,
Shawn Guo, Rob Herring, Sascha Hauer, NXP Linux Team,
linux-arm-kernel, Mark Rutland, Sam Ravnborg
On Mon, 07 Dec 2020 15:09:33 +0100, Oleksij Rempel wrote:
> Some EDT compatibles are already supported by the driver but will fail
> on checkpatch script. Fix it by syncing dt-bindings documentation with the
> driver.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
@ 2020-12-10 3:46 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Sam Ravnborg, Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, Daniel Vetter, David Jander,
Shawn Guo, linux-arm-kernel
On Mon, 07 Dec 2020 15:09:33 +0100, Oleksij Rempel wrote:
> Some EDT compatibles are already supported by the driver but will fail
> on checkpatch script. Fix it by syncing dt-bindings documentation with the
> driver.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver
@ 2020-12-10 3:46 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Sam Ravnborg, Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, David Jander, Shawn Guo,
linux-arm-kernel
On Mon, 07 Dec 2020 15:09:33 +0100, Oleksij Rempel wrote:
> Some EDT compatibles are already supported by the driver but will fail
> on checkpatch script. Fix it by syncing dt-bindings documentation with the
> driver.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2020-12-10 3:46 ` Rob Herring
-1 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Shawn Guo, Mark Rutland, Daniel Vetter, Sascha Hauer,
NXP Linux Team, David Jander, dri-devel, David Airlie,
Thierry Reding, Sam Ravnborg, Rob Herring, linux-kernel,
Pengutronix Kernel Team, linux-arm-kernel, devicetree
On Mon, 07 Dec 2020 15:09:34 +0100, Oleksij Rempel wrote:
> So far, this panel seems to be compatible with "lg,lb070wv8", on other
> hand it is better to set this compatible in the devicetree. So, let's
> add it for now only to the dt-binding documentation to fix the
> checkpatch warnings.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
@ 2020-12-10 3:46 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Sam Ravnborg, Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, Daniel Vetter, David Jander,
Shawn Guo, linux-arm-kernel
On Mon, 07 Dec 2020 15:09:34 +0100, Oleksij Rempel wrote:
> So far, this panel seems to be compatible with "lg,lb070wv8", on other
> hand it is better to set this compatible in the devicetree. So, let's
> add it for now only to the dt-binding documentation to fix the
> checkpatch warnings.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
@ 2020-12-10 3:46 ` Rob Herring
0 siblings, 0 replies; 39+ messages in thread
From: Rob Herring @ 2020-12-10 3:46 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Sam Ravnborg, Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, David Jander, Shawn Guo,
linux-arm-kernel
On Mon, 07 Dec 2020 15:09:34 +0100, Oleksij Rempel wrote:
> So far, this panel seems to be compatible with "lg,lb070wv8", on other
> hand it is better to set this compatible in the devicetree. So, let's
> add it for now only to the dt-binding documentation to fix the
> checkpatch warnings.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 0/8] mainline Plymovent M2M and BAS board
2020-12-07 14:09 ` Oleksij Rempel
(?)
@ 2021-01-07 3:10 ` Shawn Guo
-1 siblings, 0 replies; 39+ messages in thread
From: Shawn Guo @ 2021-01-07 3:10 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, Rob Herring, Sascha Hauer, Thierry Reding,
Sam Ravnborg, David Airlie, Daniel Vetter, devicetree,
Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team,
Pengutronix Kernel Team, David Jander, dri-devel
On Mon, Dec 07, 2020 at 03:09:31PM +0100, Oleksij Rempel wrote:
> changes v7:
> - panel-simple.yaml: fix comments and part order
> - panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
>
> changes v6:
> - do more panel-simple.yaml related cleanups
>
> changes v5:
> - rebase against latest shawngup/for-next
> - add patch to fix checkpatch warning on PLYM2M dts
>
> changes v4:
> - add PLYBAS board
> - PLYM2M: add touchscreen node
> - PLYM2M: add rename led nodes to led-x
>
> changes v3:
> - use old style copyright text
>
> changes v2:
> - fsl.yaml: reorder ply,plym2m
> - imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
>
> Oleksij Rempel (8):
> dt-bindings: display: simple: fix alphabetical order for EDT
> compatibles
> dt-bindings: display: simple: add EDT compatibles already supported by
> the driver
> dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
> dt-bindings: vendor-prefixes: Add an entry for Plymovent
> dt-bindings: arm: fsl: add Plymovent M2M board
> ARM: dts: add Plymovent M2M board
> dt-bindings: arm: fsl: add Plymovent BAS board
> ARM: dts: add Plymovent BAS board
Applied all, thanks.
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 0/8] mainline Plymovent M2M and BAS board
@ 2021-01-07 3:10 ` Shawn Guo
0 siblings, 0 replies; 39+ messages in thread
From: Shawn Guo @ 2021-01-07 3:10 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Fabio Estevam, Sascha Hauer, linux-kernel, dri-devel,
Rob Herring, Thierry Reding, NXP Linux Team, Daniel Vetter,
David Jander, Sam Ravnborg, linux-arm-kernel
On Mon, Dec 07, 2020 at 03:09:31PM +0100, Oleksij Rempel wrote:
> changes v7:
> - panel-simple.yaml: fix comments and part order
> - panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
>
> changes v6:
> - do more panel-simple.yaml related cleanups
>
> changes v5:
> - rebase against latest shawngup/for-next
> - add patch to fix checkpatch warning on PLYM2M dts
>
> changes v4:
> - add PLYBAS board
> - PLYM2M: add touchscreen node
> - PLYM2M: add rename led nodes to led-x
>
> changes v3:
> - use old style copyright text
>
> changes v2:
> - fsl.yaml: reorder ply,plym2m
> - imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
>
> Oleksij Rempel (8):
> dt-bindings: display: simple: fix alphabetical order for EDT
> compatibles
> dt-bindings: display: simple: add EDT compatibles already supported by
> the driver
> dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
> dt-bindings: vendor-prefixes: Add an entry for Plymovent
> dt-bindings: arm: fsl: add Plymovent M2M board
> ARM: dts: add Plymovent M2M board
> dt-bindings: arm: fsl: add Plymovent BAS board
> ARM: dts: add Plymovent BAS board
Applied all, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v7 0/8] mainline Plymovent M2M and BAS board
@ 2021-01-07 3:10 ` Shawn Guo
0 siblings, 0 replies; 39+ messages in thread
From: Shawn Guo @ 2021-01-07 3:10 UTC (permalink / raw)
To: Oleksij Rempel
Cc: Mark Rutland, devicetree, Pengutronix Kernel Team, David Airlie,
Sascha Hauer, linux-kernel, dri-devel, Rob Herring,
Thierry Reding, NXP Linux Team, David Jander, Sam Ravnborg,
linux-arm-kernel
On Mon, Dec 07, 2020 at 03:09:31PM +0100, Oleksij Rempel wrote:
> changes v7:
> - panel-simple.yaml: fix comments and part order
> - panel-simple.yaml: invent a product description for the Kyocera tcg070wvlq panel
>
> changes v6:
> - do more panel-simple.yaml related cleanups
>
> changes v5:
> - rebase against latest shawngup/for-next
> - add patch to fix checkpatch warning on PLYM2M dts
>
> changes v4:
> - add PLYBAS board
> - PLYM2M: add touchscreen node
> - PLYM2M: add rename led nodes to led-x
>
> changes v3:
> - use old style copyright text
>
> changes v2:
> - fsl.yaml: reorder ply,plym2m
> - imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
>
> Oleksij Rempel (8):
> dt-bindings: display: simple: fix alphabetical order for EDT
> compatibles
> dt-bindings: display: simple: add EDT compatibles already supported by
> the driver
> dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
> dt-bindings: vendor-prefixes: Add an entry for Plymovent
> dt-bindings: arm: fsl: add Plymovent M2M board
> ARM: dts: add Plymovent M2M board
> dt-bindings: arm: fsl: add Plymovent BAS board
> ARM: dts: add Plymovent BAS board
Applied all, thanks.
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 39+ messages in thread
end of thread, other threads:[~2021-01-07 3:13 UTC | newest]
Thread overview: 39+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-07 14:09 [PATCH v7 0/8] mainline Plymovent M2M and BAS board Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` [PATCH v7 1/8] dt-bindings: display: simple: fix alphabetical order for EDT compatibles Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-10 3:45 ` Rob Herring
2020-12-10 3:45 ` Rob Herring
2020-12-10 3:45 ` Rob Herring
2020-12-07 14:09 ` [PATCH v7 2/8] dt-bindings: display: simple: add EDT compatibles already supported by the driver Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-10 3:46 ` Rob Herring
2020-12-10 3:46 ` Rob Herring
2020-12-10 3:46 ` Rob Herring
2020-12-07 14:09 ` [PATCH v7 3/8] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-10 3:46 ` Rob Herring
2020-12-10 3:46 ` Rob Herring
2020-12-10 3:46 ` Rob Herring
2020-12-07 14:09 ` [PATCH v7 4/8] dt-bindings: vendor-prefixes: Add an entry for Plymovent Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` [PATCH v7 5/8] dt-bindings: arm: fsl: add Plymovent M2M board Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` [PATCH v7 6/8] ARM: dts: " Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` [PATCH v7 7/8] dt-bindings: arm: fsl: add Plymovent BAS board Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` [PATCH v7 8/8] ARM: dts: " Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2020-12-07 14:09 ` Oleksij Rempel
2021-01-07 3:10 ` [PATCH v7 0/8] mainline Plymovent M2M and " Shawn Guo
2021-01-07 3:10 ` Shawn Guo
2021-01-07 3:10 ` Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.