[PATCH 0/6] Regression fixes/clean ups in the Qualcomm crypto engine driver

[PATCH 0/6] Regression fixes/clean ups in the Qualcomm crypto engine driver

[Thara Gopinath]

This patch series is a result of running kernel crypto fuzz tests (by
enabling CONFIG_CRYPTO_MANAGER_EXTRA_TESTS) on the transformations
currently supported via the Qualcomm crypto engine on sdm845.
The first four patches are fixes for various regressions found during
testing. The last two patches are minor clean ups of unused variable
and parameters.

Thara Gopinath (6):
  drivers: crypto: qce: sha: Restore/save sha1_state/sha256_state with
    qce_sha_reqctx in export/import
  drivers: crypto: qce: sha: Hold back a block of data to be transferred
    as part of final
  drivers: crypto: qce: skcipher: Fix regressions found during fuzz
    testing
  drivers: crypto: qce: common: Set data unit size to message length for
    AES XTS transformation
  drivers: crypto: qce: Remover src_tbl from qce_cipher_reqctx
  drivers: crypto: qce: Remove totallen and offset in qce_start

 drivers/crypto/qce/cipher.h   |   1 -
 drivers/crypto/qce/common.c   |  25 ++++----
 drivers/crypto/qce/common.h   |   3 +-
 drivers/crypto/qce/sha.c      | 114 +++++++++-------------------------
 drivers/crypto/qce/skcipher.c |  70 ++++++++++++++++++---
 5 files changed, 101 insertions(+), 112 deletions(-)

-- 
2.25.1

[PATCH 1/6] drivers: crypto: qce: sha: Restore/save sha1_state/sha256_state with qce_sha_reqctx in export/import

[Thara Gopinath]

Export and import interfaces save and restore partial transformation
states. The partial states were being stored and restored in struct
sha1_state for sha1/hmac(sha1) transformations and sha256_state for
sha256/hmac(sha256) transformations.This led to a bunch of corner cases
where improper state was being stored and restored. A few of the corner
cases that turned up during testing are:

- wrong byte_count restored if export/import is called twice without h/w
transaction in between
- wrong buflen restored back if the pending buffer
length is exactly the block size.
- wrong state restored if buffer length is 0.

To fix these issues, save and restore the entire qce_sha_rctx structure
instead of parts of it in sha1_state and sha256_state structures.
This in turn simplifies the export and import apis.

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/sha.c | 93 ++++------------------------------------
 1 file changed, 8 insertions(+), 85 deletions(-)

diff --git a/drivers/crypto/qce/sha.c b/drivers/crypto/qce/sha.c
index 61c418c12345..b8428da6716d 100644
--- a/drivers/crypto/qce/sha.c
+++ b/drivers/crypto/qce/sha.c
@@ -139,97 +139,20 @@ static int qce_ahash_init(struct ahash_request *req)
 
 static int qce_ahash_export(struct ahash_request *req, void *out)
 {
-	struct crypto_ahash *ahash = crypto_ahash_reqtfm(req);
-	struct qce_sha_reqctx *rctx = ahash_request_ctx(req);
-	unsigned long flags = rctx->flags;
-	unsigned int digestsize = crypto_ahash_digestsize(ahash);
-	unsigned int blocksize =
-			crypto_tfm_alg_blocksize(crypto_ahash_tfm(ahash));
-
-	if (IS_SHA1(flags) || IS_SHA1_HMAC(flags)) {
-		struct sha1_state *out_state = out;
-
-		out_state->count = rctx->count;
-		qce_cpu_to_be32p_array((__be32 *)out_state->state,
-				       rctx->digest, digestsize);
-		memcpy(out_state->buffer, rctx->buf, blocksize);
-	} else if (IS_SHA256(flags) || IS_SHA256_HMAC(flags)) {
-		struct sha256_state *out_state = out;
-
-		out_state->count = rctx->count;
-		qce_cpu_to_be32p_array((__be32 *)out_state->state,
-				       rctx->digest, digestsize);
-		memcpy(out_state->buf, rctx->buf, blocksize);
-	} else {
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static int qce_import_common(struct ahash_request *req, u64 in_count,
-			     const u32 *state, const u8 *buffer, bool hmac)
-{
-	struct crypto_ahash *ahash = crypto_ahash_reqtfm(req);
 	struct qce_sha_reqctx *rctx = ahash_request_ctx(req);
-	unsigned int digestsize = crypto_ahash_digestsize(ahash);
-	unsigned int blocksize;
-	u64 count = in_count;
-
-	blocksize = crypto_tfm_alg_blocksize(crypto_ahash_tfm(ahash));
-	rctx->count = in_count;
-	memcpy(rctx->buf, buffer, blocksize);
-
-	if (in_count <= blocksize) {
-		rctx->first_blk = 1;
-	} else {
-		rctx->first_blk = 0;
-		/*
-		 * For HMAC, there is a hardware padding done when first block
-		 * is set. Therefore the byte_count must be incremened by 64
-		 * after the first block operation.
-		 */
-		if (hmac)
-			count += SHA_PADDING;
-	}
 
-	rctx->byte_count[0] = (__force __be32)(count & ~SHA_PADDING_MASK);
-	rctx->byte_count[1] = (__force __be32)(count >> 32);
-	qce_cpu_to_be32p_array((__be32 *)rctx->digest, (const u8 *)state,
-			       digestsize);
-	rctx->buflen = (unsigned int)(in_count & (blocksize - 1));
+	memcpy(out, rctx, sizeof(struct qce_sha_reqctx));
 
 	return 0;
 }
 
 static int qce_ahash_import(struct ahash_request *req, const void *in)
 {
-	struct qce_sha_reqctx *rctx;
-	unsigned long flags;
-	bool hmac;
-	int ret;
-
-	ret = qce_ahash_init(req);
-	if (ret)
-		return ret;
-
-	rctx = ahash_request_ctx(req);
-	flags = rctx->flags;
-	hmac = IS_SHA_HMAC(flags);
-
-	if (IS_SHA1(flags) || IS_SHA1_HMAC(flags)) {
-		const struct sha1_state *state = in;
+	struct qce_sha_reqctx *rctx = ahash_request_ctx(req);
 
-		ret = qce_import_common(req, state->count, state->state,
-					state->buffer, hmac);
-	} else if (IS_SHA256(flags) || IS_SHA256_HMAC(flags)) {
-		const struct sha256_state *state = in;
+	memcpy(rctx, in, sizeof(struct qce_sha_reqctx));
 
-		ret = qce_import_common(req, state->count, state->state,
-					state->buf, hmac);
-	}
-
-	return ret;
+	return 0;
 }
 
 static int qce_ahash_update(struct ahash_request *req)
@@ -450,7 +373,7 @@ static const struct qce_ahash_def ahash_def[] = {
 		.drv_name	= "sha1-qce",
 		.digestsize	= SHA1_DIGEST_SIZE,
 		.blocksize	= SHA1_BLOCK_SIZE,
-		.statesize	= sizeof(struct sha1_state),
+		.statesize	= sizeof(struct qce_sha_reqctx),
 		.std_iv		= std_iv_sha1,
 	},
 	{
@@ -459,7 +382,7 @@ static const struct qce_ahash_def ahash_def[] = {
 		.drv_name	= "sha256-qce",
 		.digestsize	= SHA256_DIGEST_SIZE,
 		.blocksize	= SHA256_BLOCK_SIZE,
-		.statesize	= sizeof(struct sha256_state),
+		.statesize	= sizeof(struct qce_sha_reqctx),
 		.std_iv		= std_iv_sha256,
 	},
 	{
@@ -468,7 +391,7 @@ static const struct qce_ahash_def ahash_def[] = {
 		.drv_name	= "hmac-sha1-qce",
 		.digestsize	= SHA1_DIGEST_SIZE,
 		.blocksize	= SHA1_BLOCK_SIZE,
-		.statesize	= sizeof(struct sha1_state),
+		.statesize	= sizeof(struct qce_sha_reqctx),
 		.std_iv		= std_iv_sha1,
 	},
 	{
@@ -477,7 +400,7 @@ static const struct qce_ahash_def ahash_def[] = {
 		.drv_name	= "hmac-sha256-qce",
 		.digestsize	= SHA256_DIGEST_SIZE,
 		.blocksize	= SHA256_BLOCK_SIZE,
-		.statesize	= sizeof(struct sha256_state),
+		.statesize	= sizeof(struct qce_sha_reqctx),
 		.std_iv		= std_iv_sha256,
 	},
 };
-- 
2.25.1

Re: [PATCH 1/6] drivers: crypto: qce: sha: Restore/save sha1_state/sha256_state with qce_sha_reqctx in export/import

[Herbert Xu]

On Fri, Dec 18, 2020 at 10:30:22PM -0500, Thara Gopinath wrote:
> Export and import interfaces save and restore partial transformation
> states. The partial states were being stored and restored in struct
> sha1_state for sha1/hmac(sha1) transformations and sha256_state for
> sha256/hmac(sha256) transformations.This led to a bunch of corner cases
> where improper state was being stored and restored. A few of the corner
> cases that turned up during testing are:
> 
> - wrong byte_count restored if export/import is called twice without h/w
> transaction in between
> - wrong buflen restored back if the pending buffer
> length is exactly the block size.
> - wrong state restored if buffer length is 0.
> 
> To fix these issues, save and restore the entire qce_sha_rctx structure
> instead of parts of it in sha1_state and sha256_state structures.
> This in turn simplifies the export and import apis.
> 
> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
> ---
>  drivers/crypto/qce/sha.c | 93 ++++------------------------------------
>  1 file changed, 8 insertions(+), 85 deletions(-)

How is this safe when the reqctx structure contains pointers?

Cheers,
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH 1/6] drivers: crypto: qce: sha: Restore/save sha1_state/sha256_state with qce_sha_reqctx in export/import

[Thara Gopinath]

On 1/2/21 4:25 PM, Herbert Xu wrote:
> On Fri, Dec 18, 2020 at 10:30:22PM -0500, Thara Gopinath wrote:
>> Export and import interfaces save and restore partial transformation
>> states. The partial states were being stored and restored in struct
>> sha1_state for sha1/hmac(sha1) transformations and sha256_state for
>> sha256/hmac(sha256) transformations.This led to a bunch of corner cases
>> where improper state was being stored and restored. A few of the corner
>> cases that turned up during testing are:
>>
>> - wrong byte_count restored if export/import is called twice without h/w
>> transaction in between
>> - wrong buflen restored back if the pending buffer
>> length is exactly the block size.
>> - wrong state restored if buffer length is 0.
>>
>> To fix these issues, save and restore the entire qce_sha_rctx structure
>> instead of parts of it in sha1_state and sha256_state structures.
>> This in turn simplifies the export and import apis.
>>
>> Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
>> ---
>>   drivers/crypto/qce/sha.c | 93 ++++------------------------------------
>>   1 file changed, 8 insertions(+), 85 deletions(-)
> 
> How is this safe when the reqctx structure contains pointers?

Hi Herbert,

You are right. Also more I think about this, it is better to have 
another struct to export and import the relevant pieces.
I will fix this and send across a v2.

> 
> Cheers,
> 

-- 
Warm Regards
Thara

[PATCH 2/6] drivers: crypto: qce: sha: Hold back a block of data to be transferred as part of final

[Thara Gopinath]

If the available data to transfer is exactly a multiple of block size, save
the last block to be transferred in qce_ahash_final (with the last block
bit set) if this is indeed the end of data stream. If not this saved block
will be transferred as part of next update. If this block is not held back
and if this is indeed the end of data stream, the digest obtained will be
wrong since qce_ahash_final will see that rctx->buflen is 0 and return
doing nothing which in turn means that a digest will not be copied to the
destination result buffer.  qce_ahash_final cannot be made to alter this
behavior and allowed to proceed if rctx->buflen is 0 because the crypto
engine BAM does not allow for zero length transfers.

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/sha.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/drivers/crypto/qce/sha.c b/drivers/crypto/qce/sha.c
index b8428da6716d..02d89267a806 100644
--- a/drivers/crypto/qce/sha.c
+++ b/drivers/crypto/qce/sha.c
@@ -193,6 +193,25 @@ static int qce_ahash_update(struct ahash_request *req)
 
 	/* calculate how many bytes will be hashed later */
 	hash_later = total % blocksize;
+
+	/*
+	 * At this point, there is more than one block size of data.  If
+	 * the available data to transfer is exactly a multiple of block
+	 * size, save the last block to be transferred in qce_ahash_final
+	 * (with the last block bit set) if this is indeed the end of data
+	 * stream. If not this saved block will be transferred as part of
+	 * next update. If this block is not held back and if this is
+	 * indeed the end of data stream, the digest obtained will be wrong
+	 * since qce_ahash_final will see that rctx->buflen is 0 and return
+	 * doing nothing which in turn means that a digest will not be
+	 * copied to the destination result buffer.  qce_ahash_final cannot
+	 * be made to alter this behavior and allowed to proceed if
+	 * rctx->buflen is 0 because the crypto engine BAM does not allow
+	 * for zero length transfers.
+	 */
+	if (!hash_later)
+		hash_later = blocksize;
+
 	if (hash_later) {
 		unsigned int src_offset = req->nbytes - hash_later;
 		scatterwalk_map_and_copy(rctx->buf, req->src, src_offset,
-- 
2.25.1

[PATCH 3/6] drivers: crypto: qce: skcipher: Fix regressions found during fuzz testing

[Thara Gopinath]

This patch contains the following fixes for the supported encryption
algorithms in the Qualcomm crypto engine(CE)
1. Return unsupported if key1 = key2 for AES XTS algorithm since CE
does not support this and the operation causes the engine to hang.
2. Return unsupprted if any three keys are same for DES3 algorithms
since CE does not support this and the operation causes the engine to
hang.
3. Return unsupported for 0 length plain texts since crypto engine BAM
dma does not support 0 length data.
4. ECB messages do not have an IV and hence set the ivsize to 0.
5. Ensure that the data passed for ECB/CBC encryption/decryption is
blocksize aligned. Otherwise the CE hangs on the operation.
6. Allow messages of length less that 512 bytes for all other encryption
algorithms other than AES XTS. The recommendation is only for AES XTS
to have data size greater than 512 bytes.

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/skcipher.c | 68 ++++++++++++++++++++++++++++++-----
 1 file changed, 60 insertions(+), 8 deletions(-)

diff --git a/drivers/crypto/qce/skcipher.c b/drivers/crypto/qce/skcipher.c
index a2d3da0ad95f..936bfb7c769b 100644
--- a/drivers/crypto/qce/skcipher.c
+++ b/drivers/crypto/qce/skcipher.c
@@ -167,16 +167,32 @@ static int qce_skcipher_setkey(struct crypto_skcipher *ablk, const u8 *key,
 	struct crypto_tfm *tfm = crypto_skcipher_tfm(ablk);
 	struct qce_cipher_ctx *ctx = crypto_tfm_ctx(tfm);
 	unsigned long flags = to_cipher_tmpl(ablk)->alg_flags;
+	unsigned int __keylen;
 	int ret;
 
 	if (!key || !keylen)
 		return -EINVAL;
 
-	switch (IS_XTS(flags) ? keylen >> 1 : keylen) {
+	/*
+	 * AES XTS key1 = key2 not supported by crypto engine.
+	 * Revisit to request a fallback cipher in this case.
+	 */
+	if (IS_XTS(flags)) {
+		__keylen = keylen >> 1;
+		if (!memcmp(key, key + __keylen, __keylen))
+			return -EINVAL;
+	} else {
+		__keylen = keylen;
+	}
+	switch (__keylen) {
 	case AES_KEYSIZE_128:
 	case AES_KEYSIZE_256:
 		memcpy(ctx->enc_key, key, keylen);
 		break;
+	case AES_KEYSIZE_192:
+		break;
+	default:
+		return -EINVAL;
 	}
 
 	ret = crypto_skcipher_setkey(ctx->fallback, key, keylen);
@@ -204,12 +220,27 @@ static int qce_des3_setkey(struct crypto_skcipher *ablk, const u8 *key,
 			   unsigned int keylen)
 {
 	struct qce_cipher_ctx *ctx = crypto_skcipher_ctx(ablk);
+	u32 _key[6];
 	int err;
 
 	err = verify_skcipher_des3_key(ablk, key);
 	if (err)
 		return err;
 
+	/*
+	 * The crypto engine does not support any two keys
+	 * being the same for triple des algorithms. The
+	 * verify_skcipher_des3_key does not check for all the
+	 * below conditions. Return -ENOKEY in case any two keys
+	 * are the same. Revisit to see if a fallback cipher
+	 * is needed to handle this condition.
+	 */
+	memcpy(_key, key, DES3_EDE_KEY_SIZE);
+	if (!((_key[0] ^ _key[2]) | (_key[1] ^ _key[3])) ||
+	    !((_key[2] ^ _key[4]) | (_key[3] ^ _key[5])) ||
+	    !((_key[0] ^ _key[4]) | (_key[1] ^ _key[5])))
+		return -ENOKEY;
+
 	ctx->enc_keylen = keylen;
 	memcpy(ctx->enc_key, key, keylen);
 	return 0;
@@ -221,6 +252,7 @@ static int qce_skcipher_crypt(struct skcipher_request *req, int encrypt)
 	struct qce_cipher_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct qce_cipher_reqctx *rctx = skcipher_request_ctx(req);
 	struct qce_alg_template *tmpl = to_cipher_tmpl(tfm);
+	unsigned int blocksize = crypto_skcipher_blocksize(tfm);
 	int keylen;
 	int ret;
 
@@ -228,14 +260,34 @@ static int qce_skcipher_crypt(struct skcipher_request *req, int encrypt)
 	rctx->flags |= encrypt ? QCE_ENCRYPT : QCE_DECRYPT;
 	keylen = IS_XTS(rctx->flags) ? ctx->enc_keylen >> 1 : ctx->enc_keylen;
 
-	/* qce is hanging when AES-XTS request len > QCE_SECTOR_SIZE and
-	 * is not a multiple of it; pass such requests to the fallback
+	/* CE does not handle 0 length messages */
+	if (!req->cryptlen)
+		return -EINVAL;
+
+	/*
+	 * ECB and CBC algorithms require message lengths to be
+	 * multiples of block size.
+	 * TODO: The spec says AES CBC mode for certain versions
+	 * of crypto engine can handle partial blocks as well.
+	 * Test and enable such messages.
+	 */
+	if (IS_ECB(rctx->flags) || IS_CBC(rctx->flags))
+		if (!IS_ALIGNED(req->cryptlen, blocksize))
+			return -EINVAL;
+
+	/*
+	 * Conditions for requesting a fallback cipher
+	 * AES-192 (not supported by crypto engine (CE))
+	 * AES-XTS request with len <= 512 byte (not recommended to use CE)
+	 * AES-XTS request with len > QCE_SECTOR_SIZE and
+	 * is not a multiple of it.(Revisit this condition to check if it is
+	 * needed in all versions of CE)
 	 */
 	if (IS_AES(rctx->flags) &&
-	    (((keylen != AES_KEYSIZE_128 && keylen != AES_KEYSIZE_256) ||
-	      req->cryptlen <= aes_sw_max_len) ||
-	     (IS_XTS(rctx->flags) && req->cryptlen > QCE_SECTOR_SIZE &&
-	      req->cryptlen % QCE_SECTOR_SIZE))) {
+	    ((keylen != AES_KEYSIZE_128 && keylen != AES_KEYSIZE_256) ||
+	    (IS_XTS(rctx->flags) && ((req->cryptlen <= aes_sw_max_len) ||
+	    (req->cryptlen > QCE_SECTOR_SIZE &&
+	    req->cryptlen % QCE_SECTOR_SIZE))))) {
 		skcipher_request_set_tfm(&rctx->fallback_req, ctx->fallback);
 		skcipher_request_set_callback(&rctx->fallback_req,
 					      req->base.flags,
@@ -307,7 +359,7 @@ static const struct qce_skcipher_def skcipher_def[] = {
 		.name		= "ecb(aes)",
 		.drv_name	= "ecb-aes-qce",
 		.blocksize	= AES_BLOCK_SIZE,
-		.ivsize		= AES_BLOCK_SIZE,
+		.ivsize		= 0,
 		.min_keysize	= AES_MIN_KEY_SIZE,
 		.max_keysize	= AES_MAX_KEY_SIZE,
 	},
-- 
2.25.1

[PATCH 4/6] drivers: crypto: qce: common: Set data unit size to message length for AES XTS transformation

[Thara Gopinath]

Set the register REG_ENCR_XTS_DU_SIZE to cryptlen for AES XTS
transformation. Anything else causes the engine to return back
wrong results.

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/common.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/crypto/qce/common.c b/drivers/crypto/qce/common.c
index 5006e74c40cd..7ae0b779563f 100644
--- a/drivers/crypto/qce/common.c
+++ b/drivers/crypto/qce/common.c
@@ -294,15 +294,15 @@ static void qce_xtskey(struct qce_device *qce, const u8 *enckey,
 {
 	u32 xtskey[QCE_MAX_CIPHER_KEY_SIZE / sizeof(u32)] = {0};
 	unsigned int xtsklen = enckeylen / (2 * sizeof(u32));
-	unsigned int xtsdusize;
 
 	qce_cpu_to_be32p_array((__be32 *)xtskey, enckey + enckeylen / 2,
 			       enckeylen / 2);
 	qce_write_array(qce, REG_ENCR_XTS_KEY0, xtskey, xtsklen);
 
-	/* xts du size 512B */
-	xtsdusize = min_t(u32, QCE_SECTOR_SIZE, cryptlen);
-	qce_write(qce, REG_ENCR_XTS_DU_SIZE, xtsdusize);
+	/* Set data unit size to cryptlen. Anything else causes
+	 * crypto engine to return back incorrect results.
+	 */
+	qce_write(qce, REG_ENCR_XTS_DU_SIZE, cryptlen);
 }
 
 static int qce_setup_regs_skcipher(struct crypto_async_request *async_req,
-- 
2.25.1

[PATCH 5/6] drivers: crypto: qce: Remover src_tbl from qce_cipher_reqctx

[Thara Gopinath]

src_table is unused and hence remove it from struct qce_cipher_reqctx

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/cipher.h | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/crypto/qce/cipher.h b/drivers/crypto/qce/cipher.h
index cffa9fc628ff..850f257d00f3 100644
--- a/drivers/crypto/qce/cipher.h
+++ b/drivers/crypto/qce/cipher.h
@@ -40,7 +40,6 @@ struct qce_cipher_reqctx {
 	struct scatterlist result_sg;
 	struct sg_table dst_tbl;
 	struct scatterlist *dst_sg;
-	struct sg_table src_tbl;
 	struct scatterlist *src_sg;
 	unsigned int cryptlen;
 	struct skcipher_request fallback_req;	// keep at the end
-- 
2.25.1

[PATCH 6/6] drivers: crypto: qce: Remove totallen and offset in qce_start

[Thara Gopinath]

totallen is used to get the size of the data to be transformed.
This is also available via nbytes or cryptlen in the qce_sha_reqctx
and qce_cipher_ctx. Similarly offset convey nothing for the supported
encryption and authentication transformations and is always 0.
Remove these two redundant parameters in qce_start.

Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
---
 drivers/crypto/qce/common.c   | 17 +++++++----------
 drivers/crypto/qce/common.h   |  3 +--
 drivers/crypto/qce/sha.c      |  2 +-
 drivers/crypto/qce/skcipher.c |  2 +-
 4 files changed, 10 insertions(+), 14 deletions(-)

diff --git a/drivers/crypto/qce/common.c b/drivers/crypto/qce/common.c
index 7ae0b779563f..e292d8453ef6 100644
--- a/drivers/crypto/qce/common.c
+++ b/drivers/crypto/qce/common.c
@@ -139,8 +139,7 @@ static u32 qce_auth_cfg(unsigned long flags, u32 key_size)
 	return cfg;
 }
 
-static int qce_setup_regs_ahash(struct crypto_async_request *async_req,
-				u32 totallen, u32 offset)
+static int qce_setup_regs_ahash(struct crypto_async_request *async_req)
 {
 	struct ahash_request *req = ahash_request_cast(async_req);
 	struct crypto_ahash *ahash = __crypto_ahash_cast(async_req->tfm);
@@ -305,8 +304,7 @@ static void qce_xtskey(struct qce_device *qce, const u8 *enckey,
 	qce_write(qce, REG_ENCR_XTS_DU_SIZE, cryptlen);
 }
 
-static int qce_setup_regs_skcipher(struct crypto_async_request *async_req,
-				     u32 totallen, u32 offset)
+static int qce_setup_regs_skcipher(struct crypto_async_request *async_req)
 {
 	struct skcipher_request *req = skcipher_request_cast(async_req);
 	struct qce_cipher_reqctx *rctx = skcipher_request_ctx(req);
@@ -366,7 +364,7 @@ static int qce_setup_regs_skcipher(struct crypto_async_request *async_req,
 
 	qce_write(qce, REG_ENCR_SEG_CFG, encr_cfg);
 	qce_write(qce, REG_ENCR_SEG_SIZE, rctx->cryptlen);
-	qce_write(qce, REG_ENCR_SEG_START, offset & 0xffff);
+	qce_write(qce, REG_ENCR_SEG_START, 0);
 
 	if (IS_CTR(flags)) {
 		qce_write(qce, REG_CNTR_MASK, ~0);
@@ -375,7 +373,7 @@ static int qce_setup_regs_skcipher(struct crypto_async_request *async_req,
 		qce_write(qce, REG_CNTR_MASK2, ~0);
 	}
 
-	qce_write(qce, REG_SEG_SIZE, totallen);
+	qce_write(qce, REG_SEG_SIZE, rctx->cryptlen);
 
 	/* get little endianness */
 	config = qce_config_reg(qce, 1);
@@ -387,17 +385,16 @@ static int qce_setup_regs_skcipher(struct crypto_async_request *async_req,
 }
 #endif
 
-int qce_start(struct crypto_async_request *async_req, u32 type, u32 totallen,
-	      u32 offset)
+int qce_start(struct crypto_async_request *async_req, u32 type)
 {
 	switch (type) {
 #ifdef CONFIG_CRYPTO_DEV_QCE_SKCIPHER
 	case CRYPTO_ALG_TYPE_SKCIPHER:
-		return qce_setup_regs_skcipher(async_req, totallen, offset);
+		return qce_setup_regs_skcipher(async_req);
 #endif
 #ifdef CONFIG_CRYPTO_DEV_QCE_SHA
 	case CRYPTO_ALG_TYPE_AHASH:
-		return qce_setup_regs_ahash(async_req, totallen, offset);
+		return qce_setup_regs_ahash(async_req);
 #endif
 	default:
 		return -EINVAL;
diff --git a/drivers/crypto/qce/common.h b/drivers/crypto/qce/common.h
index 85ba16418a04..3bc244bcca2d 100644
--- a/drivers/crypto/qce/common.h
+++ b/drivers/crypto/qce/common.h
@@ -94,7 +94,6 @@ struct qce_alg_template {
 void qce_cpu_to_be32p_array(__be32 *dst, const u8 *src, unsigned int len);
 int qce_check_status(struct qce_device *qce, u32 *status);
 void qce_get_version(struct qce_device *qce, u32 *major, u32 *minor, u32 *step);
-int qce_start(struct crypto_async_request *async_req, u32 type, u32 totallen,
-	      u32 offset);
+int qce_start(struct crypto_async_request *async_req, u32 type);
 
 #endif /* _COMMON_H_ */
diff --git a/drivers/crypto/qce/sha.c b/drivers/crypto/qce/sha.c
index 02d89267a806..141cfe14574d 100644
--- a/drivers/crypto/qce/sha.c
+++ b/drivers/crypto/qce/sha.c
@@ -107,7 +107,7 @@ static int qce_ahash_async_req_handle(struct crypto_async_request *async_req)
 
 	qce_dma_issue_pending(&qce->dma);
 
-	ret = qce_start(async_req, tmpl->crypto_alg_type, 0, 0);
+	ret = qce_start(async_req, tmpl->crypto_alg_type);
 	if (ret)
 		goto error_terminate;
 
diff --git a/drivers/crypto/qce/skcipher.c b/drivers/crypto/qce/skcipher.c
index 936bfb7c769b..2f327640b4de 100644
--- a/drivers/crypto/qce/skcipher.c
+++ b/drivers/crypto/qce/skcipher.c
@@ -143,7 +143,7 @@ qce_skcipher_async_req_handle(struct crypto_async_request *async_req)
 
 	qce_dma_issue_pending(&qce->dma);
 
-	ret = qce_start(async_req, tmpl->crypto_alg_type, req->cryptlen, 0);
+	ret = qce_start(async_req, tmpl->crypto_alg_type);
 	if (ret)
 		goto error_terminate;
 
-- 
2.25.1