* [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay
@ 2021-01-04 21:28 Pawel Dembicki
2021-01-04 21:28 ` [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171 Pawel Dembicki
2021-01-05 7:41 ` [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Chris Packham
0 siblings, 2 replies; 4+ messages in thread
From: Pawel Dembicki @ 2021-01-04 21:28 UTC (permalink / raw)
To: u-boot
Clock delay in RGMII is required for some boards.
Clock delay is read from phy-mode dts property. Delay is configured via
proper bits in PORT_REG_PHYS_CTRL register.
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
---
Changes in v3:
- clear initial values of RX and TX delay bit
Changes in v2:
- change source info about delay: from hardcode to phy-mode propoperty in dts
drivers/net/phy/mv88e61xx.c | 66 ++++++++++++++++++++++++++++++++++++-
1 file changed, 65 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
index 7eff37b244..3bcd2ba242 100644
--- a/drivers/net/phy/mv88e61xx.c
+++ b/drivers/net/phy/mv88e61xx.c
@@ -97,6 +97,8 @@
#define PORT_REG_STATUS_CMODE_1000BASE_X 0x9
#define PORT_REG_STATUS_CMODE_SGMII 0xa
+#define PORT_REG_PHYS_CTRL_RGMII_RX_DELAY BIT(15)
+#define PORT_REG_PHYS_CTRL_RGMII_TX_DELAY BIT(14)
#define PORT_REG_PHYS_CTRL_PCS_AN_EN BIT(10)
#define PORT_REG_PHYS_CTRL_PCS_AN_RST BIT(9)
#define PORT_REG_PHYS_CTRL_FC_VALUE BIT(7)
@@ -729,7 +731,45 @@ unforce:
static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)
{
struct mv88e61xx_phy_priv *priv = phydev->priv;
- int val;
+ ofnode node;
+ const char *str;
+ int val, phy_mode;
+ u32 phy_handle;
+
+ if (!ofnode_valid(phydev->node)) {
+ node = dev_ofnode(phydev->dev);
+ phy_handle = ofnode_read_u32_default(node, "phy-handle", -ENXIO);
+
+ if (phy_handle == -ENXIO) {
+ node = ofnode_first_subnode(node);
+
+ while (ofnode_valid(node)) {
+ phy_handle = ofnode_read_u32_default(node, "phy-handle", -ENXIO);
+ if (phy_handle != -ENXIO)
+ break;
+ node = ofnode_next_subnode(node);
+ }
+ }
+
+ if (phy_handle != -ENXIO)
+ node = ofnode_get_by_phandle(phy_handle);
+ else
+ node = ofnode_null();
+ } else {
+ node = phy_get_ofnode(phydev);
+ }
+
+ node = ofnode_find_subnode(node, "ports");
+ node = ofnode_first_subnode(node);
+
+ while (ofnode_valid(node)) {
+ u8 port_no = (u8)ofnode_read_u32_default(node, "reg", -1);
+
+ if (port_no == port)
+ break;
+
+ node = ofnode_next_subnode(node);
+ }
val = mv88e61xx_port_read(phydev, port, PORT_REG_PHYS_CTRL);
if (val < 0)
@@ -754,6 +794,30 @@ static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)
val |= PORT_REG_PHYS_CTRL_LINK_VALUE |
PORT_REG_PHYS_CTRL_LINK_FORCE;
+ if (ofnode_valid(node)) {
+ str = ofnode_read_string(node, "phy-mode");
+ if (str) {
+ phy_mode = phy_get_interface_by_name(str);
+ val &= ~(PORT_REG_PHYS_CTRL_RGMII_RX_DELAY |
+ PORT_REG_PHYS_CTRL_RGMII_TX_DELAY);
+
+ switch (phy_mode) {
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val |= PORT_REG_PHYS_CTRL_RGMII_RX_DELAY;
+ val |= PORT_REG_PHYS_CTRL_RGMII_TX_DELAY;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val |= PORT_REG_PHYS_CTRL_RGMII_RX_DELAY;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ val |= PORT_REG_PHYS_CTRL_RGMII_TX_DELAY;
+ break;
+ default:
+ break;
+ }
+ }
+ }
+
return mv88e61xx_port_write(phydev, port, PORT_REG_PHYS_CTRL,
val);
}
--
2.25.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171
2021-01-04 21:28 [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Pawel Dembicki
@ 2021-01-04 21:28 ` Pawel Dembicki
2021-01-05 7:43 ` Chris Packham
2021-01-05 7:41 ` [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Chris Packham
1 sibling, 1 reply; 4+ messages in thread
From: Pawel Dembicki @ 2021-01-04 21:28 UTC (permalink / raw)
To: u-boot
This patch add MV88E6171 id to driver data.
Tested on Checkpoint L-50 board.
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
---
Changes in v3,v2:
- resend only
drivers/net/phy/mv88e61xx.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
index 3bcd2ba242..82f1587ff5 100644
--- a/drivers/net/phy/mv88e61xx.c
+++ b/drivers/net/phy/mv88e61xx.c
@@ -183,6 +183,7 @@
#define PORT_SWITCH_ID_6071 0x0710
#define PORT_SWITCH_ID_6096 0x0980
#define PORT_SWITCH_ID_6097 0x0990
+#define PORT_SWITCH_ID_6171 0x1710
#define PORT_SWITCH_ID_6172 0x1720
#define PORT_SWITCH_ID_6176 0x1760
#define PORT_SWITCH_ID_6220 0x2200
@@ -1055,6 +1056,7 @@ static int mv88e61xx_probe(struct phy_device *phydev)
switch (priv->id) {
case PORT_SWITCH_ID_6096:
case PORT_SWITCH_ID_6097:
+ case PORT_SWITCH_ID_6171:
case PORT_SWITCH_ID_6172:
case PORT_SWITCH_ID_6176:
case PORT_SWITCH_ID_6240:
@@ -1210,6 +1212,17 @@ static struct phy_driver mv88e61xx_driver = {
.shutdown = &genphy_shutdown,
};
+static struct phy_driver mv88e617x_driver = {
+ .name = "Marvell MV88E617x",
+ .uid = 0x01410e70,
+ .mask = 0xfffffff0,
+ .features = PHY_GBIT_FEATURES,
+ .probe = mv88e61xx_probe,
+ .config = mv88e61xx_phy_config,
+ .startup = mv88e61xx_phy_startup,
+ .shutdown = &genphy_shutdown,
+};
+
static struct phy_driver mv88e609x_driver = {
.name = "Marvell MV88E609x",
.uid = 0x1410c89,
@@ -1235,6 +1248,7 @@ static struct phy_driver mv88e6071_driver = {
int phy_mv88e61xx_init(void)
{
phy_register(&mv88e61xx_driver);
+ phy_register(&mv88e617x_driver);
phy_register(&mv88e609x_driver);
phy_register(&mv88e6071_driver);
--
2.25.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay
2021-01-04 21:28 [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Pawel Dembicki
2021-01-04 21:28 ` [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171 Pawel Dembicki
@ 2021-01-05 7:41 ` Chris Packham
1 sibling, 0 replies; 4+ messages in thread
From: Chris Packham @ 2021-01-05 7:41 UTC (permalink / raw)
To: u-boot
On Tue, 5 Jan 2021, 10:28 AM Pawel Dembicki, <paweldembicki@gmail.com>
wrote:
> Clock delay in RGMII is required for some boards.
>
> Clock delay is read from phy-mode dts property. Delay is configured via
> proper bits in PORT_REG_PHYS_CTRL register.
>
> Cc: Chris Packham <judge.packham@gmail.com>
> Cc: Joe Hershberger <joe.hershberger@ni.com>
> Cc: Anatolij Gustschin <agust@denx.de>
> Cc: Tim Harvey <tharvey@gateworks.com>
> Cc: Tom Rini <trini@konsulko.com>
> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
>
Looks good to me.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
---
> Changes in v3:
> - clear initial values of RX and TX delay bit
> Changes in v2:
> - change source info about delay: from hardcode to phy-mode propoperty in
> dts
> drivers/net/phy/mv88e61xx.c | 66 ++++++++++++++++++++++++++++++++++++-
> 1 file changed, 65 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
> index 7eff37b244..3bcd2ba242 100644
> --- a/drivers/net/phy/mv88e61xx.c
> +++ b/drivers/net/phy/mv88e61xx.c
> @@ -97,6 +97,8 @@
> #define PORT_REG_STATUS_CMODE_1000BASE_X 0x9
> #define PORT_REG_STATUS_CMODE_SGMII 0xa
>
> +#define PORT_REG_PHYS_CTRL_RGMII_RX_DELAY BIT(15)
> +#define PORT_REG_PHYS_CTRL_RGMII_TX_DELAY BIT(14)
> #define PORT_REG_PHYS_CTRL_PCS_AN_EN BIT(10)
> #define PORT_REG_PHYS_CTRL_PCS_AN_RST BIT(9)
> #define PORT_REG_PHYS_CTRL_FC_VALUE BIT(7)
> @@ -729,7 +731,45 @@ unforce:
> static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)
> {
> struct mv88e61xx_phy_priv *priv = phydev->priv;
> - int val;
> + ofnode node;
> + const char *str;
> + int val, phy_mode;
> + u32 phy_handle;
> +
> + if (!ofnode_valid(phydev->node)) {
> + node = dev_ofnode(phydev->dev);
> + phy_handle = ofnode_read_u32_default(node, "phy-handle",
> -ENXIO);
> +
> + if (phy_handle == -ENXIO) {
> + node = ofnode_first_subnode(node);
> +
> + while (ofnode_valid(node)) {
> + phy_handle = ofnode_read_u32_default(node,
> "phy-handle", -ENXIO);
> + if (phy_handle != -ENXIO)
> + break;
> + node = ofnode_next_subnode(node);
> + }
> + }
> +
> + if (phy_handle != -ENXIO)
> + node = ofnode_get_by_phandle(phy_handle);
> + else
> + node = ofnode_null();
> + } else {
> + node = phy_get_ofnode(phydev);
> + }
> +
> + node = ofnode_find_subnode(node, "ports");
> + node = ofnode_first_subnode(node);
> +
> + while (ofnode_valid(node)) {
> + u8 port_no = (u8)ofnode_read_u32_default(node, "reg", -1);
> +
> + if (port_no == port)
> + break;
> +
> + node = ofnode_next_subnode(node);
> + }
>
> val = mv88e61xx_port_read(phydev, port, PORT_REG_PHYS_CTRL);
> if (val < 0)
> @@ -754,6 +794,30 @@ static int mv88e61xx_fixed_port_setup(struct
> phy_device *phydev, u8 port)
> val |= PORT_REG_PHYS_CTRL_LINK_VALUE |
> PORT_REG_PHYS_CTRL_LINK_FORCE;
>
> + if (ofnode_valid(node)) {
> + str = ofnode_read_string(node, "phy-mode");
> + if (str) {
> + phy_mode = phy_get_interface_by_name(str);
> + val &= ~(PORT_REG_PHYS_CTRL_RGMII_RX_DELAY |
> + PORT_REG_PHYS_CTRL_RGMII_TX_DELAY);
> +
> + switch (phy_mode) {
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + val |= PORT_REG_PHYS_CTRL_RGMII_RX_DELAY;
> + val |= PORT_REG_PHYS_CTRL_RGMII_TX_DELAY;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + val |= PORT_REG_PHYS_CTRL_RGMII_RX_DELAY;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + val |= PORT_REG_PHYS_CTRL_RGMII_TX_DELAY;
> + break;
> + default:
> + break;
> + }
> + }
> + }
> +
> return mv88e61xx_port_write(phydev, port, PORT_REG_PHYS_CTRL,
> val);
> }
> --
> 2.25.1
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171
2021-01-04 21:28 ` [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171 Pawel Dembicki
@ 2021-01-05 7:43 ` Chris Packham
0 siblings, 0 replies; 4+ messages in thread
From: Chris Packham @ 2021-01-05 7:43 UTC (permalink / raw)
To: u-boot
On Tue, 5 Jan 2021, 10:28 AM Pawel Dembicki, <paweldembicki@gmail.com>
wrote:
> This patch add MV88E6171 id to driver data.
>
> Tested on Checkpoint L-50 board.
>
> Cc: Chris Packham <judge.packham@gmail.com>
> Cc: Joe Hershberger <joe.hershberger@ni.com>
> Cc: Anatolij Gustschin <agust@denx.de>
> Cc: Tim Harvey <tharvey@gateworks.com>
> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
>
Looks good to me.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
---
> Changes in v3,v2:
> - resend only
> drivers/net/phy/mv88e61xx.c | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
> index 3bcd2ba242..82f1587ff5 100644
> --- a/drivers/net/phy/mv88e61xx.c
> +++ b/drivers/net/phy/mv88e61xx.c
> @@ -183,6 +183,7 @@
> #define PORT_SWITCH_ID_6071 0x0710
> #define PORT_SWITCH_ID_6096 0x0980
> #define PORT_SWITCH_ID_6097 0x0990
> +#define PORT_SWITCH_ID_6171 0x1710
> #define PORT_SWITCH_ID_6172 0x1720
> #define PORT_SWITCH_ID_6176 0x1760
> #define PORT_SWITCH_ID_6220 0x2200
> @@ -1055,6 +1056,7 @@ static int mv88e61xx_probe(struct phy_device *phydev)
> switch (priv->id) {
> case PORT_SWITCH_ID_6096:
> case PORT_SWITCH_ID_6097:
> + case PORT_SWITCH_ID_6171:
> case PORT_SWITCH_ID_6172:
> case PORT_SWITCH_ID_6176:
> case PORT_SWITCH_ID_6240:
> @@ -1210,6 +1212,17 @@ static struct phy_driver mv88e61xx_driver = {
> .shutdown = &genphy_shutdown,
> };
>
> +static struct phy_driver mv88e617x_driver = {
> + .name = "Marvell MV88E617x",
> + .uid = 0x01410e70,
> + .mask = 0xfffffff0,
> + .features = PHY_GBIT_FEATURES,
> + .probe = mv88e61xx_probe,
> + .config = mv88e61xx_phy_config,
> + .startup = mv88e61xx_phy_startup,
> + .shutdown = &genphy_shutdown,
> +};
> +
> static struct phy_driver mv88e609x_driver = {
> .name = "Marvell MV88E609x",
> .uid = 0x1410c89,
> @@ -1235,6 +1248,7 @@ static struct phy_driver mv88e6071_driver = {
> int phy_mv88e61xx_init(void)
> {
> phy_register(&mv88e61xx_driver);
> + phy_register(&mv88e617x_driver);
> phy_register(&mv88e609x_driver);
> phy_register(&mv88e6071_driver);
>
> --
> 2.25.1
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-01-05 7:43 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-01-04 21:28 [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Pawel Dembicki
2021-01-04 21:28 ` [PATCH v3 2/2] phy: mv88e61xx: add support for MV88E6171 Pawel Dembicki
2021-01-05 7:43 ` Chris Packham
2021-01-05 7:41 ` [PATCH v3 1/2] phy: mv88e61xx: add support for RGMII TX/RX delay Chris Packham
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.