* [PATCH v4 0/7] dt-bindings: display: Convert DWC HDMI TX bindings to YAML
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Hello,
This patch series attempts a conversion of the DWC HDMI TX DT bindings
to YAML.
The DWC HDMI TX is an HDMI transmitter IP core from Synopsys, integrated
in various SoCs with different glue layers. As such, some properties are
defined in a common document, but sometimes need to be overridden by
platform-specific bindings.
Compared to v3, the series incorporates small review feedback, and has
gained patch 1/7 that updated the imx6q(dl) device trees to use 'ports'
nodes. Patch 2/7 then adds a base schema for the common properties,
based on the existing dw_hdmi.txt document. Patches 3/7 to 5/7 then
convert the platform-specific bindings for Renesas, NXP and Rockchip
SoCs. Patch 6/7 replaces the reference to dw_hdmi.txt in the Allwinner
bindings with a reference to the YAML base schema, and patch 7/7 drops
dw_hdmi.txt.
I have volunteered Philipp Zabel and Mark Yao as maintainers for the
i.MX6 and Rockchip bindings respectively. Could you please let me know
if you would prefer a different maintainer, or ack the respective patch
if this is fine with you ?
It seems to be difficult to find a maintainer for the RockChip bindings.
In the event that no maintainer can be found, Rob has recommended to
simply delete the text-based bindings, which I would prefer not being
forced to do in a v5.
Laurent Pinchart (7):
ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder
dt-bindings: display: bridge: Add YAML schema for Synopsys DW-HDMI
dt-bindings: display: bridge: renesas,dw-hdmi: Convert binding to YAML
dt-bindings: display: imx: hdmi: Convert binding to YAML
dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
dt-bindings: display: sun8i-a83t-dw-hdmi: Reference dw-hdmi YAML
schema
dt-bindings: display: bridge: Remove deprecated dw_hdmi.txt
.../display/allwinner,sun8i-a83t-dw-hdmi.yaml | 4 +-
.../bindings/display/bridge/dw_hdmi.txt | 33 ----
.../display/bridge/renesas,dw-hdmi.txt | 88 ----------
.../display/bridge/renesas,dw-hdmi.yaml | 125 ++++++++++++++
.../display/bridge/synopsys,dw-hdmi.yaml | 55 ++++++
.../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++
.../devicetree/bindings/display/imx/hdmi.txt | 65 --------
.../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
.../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
MAINTAINERS | 2 +-
arch/arm/boot/dts/imx6q.dtsi | 20 ++-
arch/arm/boot/dts/imx6qdl.dtsi | 25 +--
12 files changed, 490 insertions(+), 283 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
delete mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
create mode 100644 Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH v4 0/7] dt-bindings: display: Convert DWC HDMI TX bindings to YAML
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Hello,
This patch series attempts a conversion of the DWC HDMI TX DT bindings
to YAML.
The DWC HDMI TX is an HDMI transmitter IP core from Synopsys, integrated
in various SoCs with different glue layers. As such, some properties are
defined in a common document, but sometimes need to be overridden by
platform-specific bindings.
Compared to v3, the series incorporates small review feedback, and has
gained patch 1/7 that updated the imx6q(dl) device trees to use 'ports'
nodes. Patch 2/7 then adds a base schema for the common properties,
based on the existing dw_hdmi.txt document. Patches 3/7 to 5/7 then
convert the platform-specific bindings for Renesas, NXP and Rockchip
SoCs. Patch 6/7 replaces the reference to dw_hdmi.txt in the Allwinner
bindings with a reference to the YAML base schema, and patch 7/7 drops
dw_hdmi.txt.
I have volunteered Philipp Zabel and Mark Yao as maintainers for the
i.MX6 and Rockchip bindings respectively. Could you please let me know
if you would prefer a different maintainer, or ack the respective patch
if this is fine with you ?
It seems to be difficult to find a maintainer for the RockChip bindings.
In the event that no maintainer can be found, Rob has recommended to
simply delete the text-based bindings, which I would prefer not being
forced to do in a v5.
Laurent Pinchart (7):
ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder
dt-bindings: display: bridge: Add YAML schema for Synopsys DW-HDMI
dt-bindings: display: bridge: renesas,dw-hdmi: Convert binding to YAML
dt-bindings: display: imx: hdmi: Convert binding to YAML
dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
dt-bindings: display: sun8i-a83t-dw-hdmi: Reference dw-hdmi YAML
schema
dt-bindings: display: bridge: Remove deprecated dw_hdmi.txt
.../display/allwinner,sun8i-a83t-dw-hdmi.yaml | 4 +-
.../bindings/display/bridge/dw_hdmi.txt | 33 ----
.../display/bridge/renesas,dw-hdmi.txt | 88 ----------
.../display/bridge/renesas,dw-hdmi.yaml | 125 ++++++++++++++
.../display/bridge/synopsys,dw-hdmi.yaml | 55 ++++++
.../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++
.../devicetree/bindings/display/imx/hdmi.txt | 65 --------
.../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
.../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
MAINTAINERS | 2 +-
arch/arm/boot/dts/imx6q.dtsi | 20 ++-
arch/arm/boot/dts/imx6qdl.dtsi | 25 +--
12 files changed, 490 insertions(+), 283 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
delete mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
create mode 100644 Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH v4 1/7] ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
In preparation for the conversion of the DWC HDMI TX device tree
bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports'
node. The 'ports' node is optional in the OF graph implementation, but
YAML bindings require it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
arch/arm/boot/dts/imx6q.dtsi | 20 +++++++++++---------
arch/arm/boot/dts/imx6qdl.dtsi | 25 ++++++++++++++-----------
2 files changed, 25 insertions(+), 20 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 5277e3903291..8d209c1b3ca7 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -406,19 +406,21 @@ ipu2_csi1_mux_to_ipu2_csi1: endpoint {
&hdmi {
compatible = "fsl,imx6q-hdmi";
- port@2 {
- reg = <2>;
+ ports {
+ port@2 {
+ reg = <2>;
- hdmi_mux_2: endpoint {
- remote-endpoint = <&ipu2_di0_hdmi>;
+ hdmi_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_hdmi>;
+ };
};
- };
- port@3 {
- reg = <3>;
+ port@3 {
+ reg = <3>;
- hdmi_mux_3: endpoint {
- remote-endpoint = <&ipu2_di1_hdmi>;
+ hdmi_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_hdmi>;
+ };
};
};
};
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 6f59a99cbe82..82e01ce026ea 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -182,8 +182,6 @@ gpmi: nand-controller@112000 {
};
hdmi: hdmi@120000 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0x00120000 0x9000>;
interrupts = <0 115 0x04>;
gpr = <&gpr>;
@@ -192,19 +190,24 @@ hdmi: hdmi@120000 {
clock-names = "iahb", "isfr";
status = "disabled";
- port@0 {
- reg = <0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
};
- };
- port@1 {
- reg = <1>;
+ port@1 {
+ reg = <1>;
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
};
};
};
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 1/7] ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
In preparation for the conversion of the DWC HDMI TX device tree
bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports'
node. The 'ports' node is optional in the OF graph implementation, but
YAML bindings require it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
arch/arm/boot/dts/imx6q.dtsi | 20 +++++++++++---------
arch/arm/boot/dts/imx6qdl.dtsi | 25 ++++++++++++++-----------
2 files changed, 25 insertions(+), 20 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 5277e3903291..8d209c1b3ca7 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -406,19 +406,21 @@ ipu2_csi1_mux_to_ipu2_csi1: endpoint {
&hdmi {
compatible = "fsl,imx6q-hdmi";
- port@2 {
- reg = <2>;
+ ports {
+ port@2 {
+ reg = <2>;
- hdmi_mux_2: endpoint {
- remote-endpoint = <&ipu2_di0_hdmi>;
+ hdmi_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_hdmi>;
+ };
};
- };
- port@3 {
- reg = <3>;
+ port@3 {
+ reg = <3>;
- hdmi_mux_3: endpoint {
- remote-endpoint = <&ipu2_di1_hdmi>;
+ hdmi_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_hdmi>;
+ };
};
};
};
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 6f59a99cbe82..82e01ce026ea 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -182,8 +182,6 @@ gpmi: nand-controller@112000 {
};
hdmi: hdmi@120000 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0x00120000 0x9000>;
interrupts = <0 115 0x04>;
gpr = <&gpr>;
@@ -192,19 +190,24 @@ hdmi: hdmi@120000 {
clock-names = "iahb", "isfr";
status = "disabled";
- port@0 {
- reg = <0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
};
- };
- port@1 {
- reg = <1>;
+ port@1 {
+ reg = <1>;
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
};
};
};
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 2/7] dt-bindings: display: bridge: Add YAML schema for Synopsys DW-HDMI
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Add a .yaml schema containing the common properties for the Synopsys
DesignWare HDMI TX controller. This isn't a full device tree binding
specification, but is meant to be referenced by platform-specific
bindings for the IP core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Drop ports property
Changes since v1:
- Add default to reg-io-width property
- Add additionalProperties
- Rebase on top of OF graph schema, dropped redundant properties
- Drop cec clock as it's device-specific
- Increase max clocks to 5 to accommodate the Rockchip DW-HDMI
---
.../display/bridge/synopsys,dw-hdmi.yaml | 55 +++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
new file mode 100644
index 000000000000..9be44a682e67
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/synopsys,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Synopsys DesignWare HDMI TX Controller
+
+maintainers:
+ - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+ This document defines device tree properties for the Synopsys DesignWare HDMI
+ TX controller (DWC HDMI TX) IP core. It doesn't constitute a full device tree
+ binding specification by itself but is meant to be referenced by device tree
+ bindings for the platform-specific integrations of the DWC HDMI TX.
+
+ When referenced from platform device tree bindings the properties defined in
+ this document are defined as follows. The platform device tree bindings are
+ responsible for defining whether each property is required or optional.
+
+properties:
+ reg:
+ maxItems: 1
+
+ reg-io-width:
+ description:
+ Width (in bytes) of the registers specified by the reg property.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 4]
+ default: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 5
+ items:
+ - description: The bus clock for either AHB and APB
+ - description: The internal register configuration clock
+ additionalItems: true
+
+ clock-names:
+ minItems: 2
+ maxItems: 5
+ items:
+ - const: iahb
+ - const: isfr
+ additionalItems: true
+
+ interrupts:
+ maxItems: 1
+
+additionalProperties: true
+
+...
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 2/7] dt-bindings: display: bridge: Add YAML schema for Synopsys DW-HDMI
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Add a .yaml schema containing the common properties for the Synopsys
DesignWare HDMI TX controller. This isn't a full device tree binding
specification, but is meant to be referenced by platform-specific
bindings for the IP core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Drop ports property
Changes since v1:
- Add default to reg-io-width property
- Add additionalProperties
- Rebase on top of OF graph schema, dropped redundant properties
- Drop cec clock as it's device-specific
- Increase max clocks to 5 to accommodate the Rockchip DW-HDMI
---
.../display/bridge/synopsys,dw-hdmi.yaml | 55 +++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
new file mode 100644
index 000000000000..9be44a682e67
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/synopsys,dw-hdmi.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/synopsys,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Synopsys DesignWare HDMI TX Controller
+
+maintainers:
+ - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+ This document defines device tree properties for the Synopsys DesignWare HDMI
+ TX controller (DWC HDMI TX) IP core. It doesn't constitute a full device tree
+ binding specification by itself but is meant to be referenced by device tree
+ bindings for the platform-specific integrations of the DWC HDMI TX.
+
+ When referenced from platform device tree bindings the properties defined in
+ this document are defined as follows. The platform device tree bindings are
+ responsible for defining whether each property is required or optional.
+
+properties:
+ reg:
+ maxItems: 1
+
+ reg-io-width:
+ description:
+ Width (in bytes) of the registers specified by the reg property.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 4]
+ default: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 5
+ items:
+ - description: The bus clock for either AHB and APB
+ - description: The internal register configuration clock
+ additionalItems: true
+
+ clock-names:
+ minItems: 2
+ maxItems: 5
+ items:
+ - const: iahb
+ - const: isfr
+ additionalItems: true
+
+ interrupts:
+ maxItems: 1
+
+additionalProperties: true
+
+...
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 3/7] dt-bindings: display: bridge: renesas,dw-hdmi: Convert binding to YAML
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Convert the Renesas R-Car DWC HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Use port instead of port-base
Changes since v2:
- Update MAINTAINERS
Changes since v1:
- Drop the part numbers in comments, only keep the SoC names
- Use unevaluatedProperties instead of additionalProperties
- Only specify maxItems for clocks and clock-names
- Drop reg, interrupts, #address-cells and #size-cells as they're
checked in the base schema
- Use one size and address cell in example
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
---
.../display/bridge/renesas,dw-hdmi.txt | 88 ------------
.../display/bridge/renesas,dw-hdmi.yaml | 125 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 126 insertions(+), 89 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
deleted file mode 100644
index 3f6072651182..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-Renesas Gen3 DWC HDMI TX Encoder
-================================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible : Shall contain one or more of
- - "renesas,r8a774a1-hdmi" for R8A774A1 (RZ/G2M) compatible HDMI TX
- - "renesas,r8a774b1-hdmi" for R8A774B1 (RZ/G2N) compatible HDMI TX
- - "renesas,r8a774e1-hdmi" for R8A774E1 (RZ/G2H) compatible HDMI TX
- - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
- - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX
- - "renesas,r8a77961-hdmi" for R8A77961 (R-Car M3-W+) compatible HDMI TX
- - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX
- - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 and RZ/G2 compatible
- HDMI TX
-
- When compatible with generic versions, nodes must list the SoC-specific
- version corresponding to the platform first, followed by the
- family-specific version.
-
-- reg: See dw_hdmi.txt.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have one port numbered 0
- corresponding to the video input of the controller and one port numbered 1
- corresponding to its HDMI output, and one port numbered 2 corresponding to
- sound input of the controller. Each port shall have a single endpoint.
-
-Optional properties:
-
-- power-domains: Shall reference the power domain that contains the DWC HDMI,
- if any.
-
-
-Example:
-
- hdmi0: hdmi@fead0000 {
- compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
- reg = <0 0xfead0000 0 0x10000>;
- interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
- clock-names = "iahb", "isfr";
- power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- dw_hdmi0_in: endpoint {
- remote-endpoint = <&du_out_hdmi0>;
- };
- };
- port@1 {
- reg = <1>;
- rcar_dw_hdmi0_out: endpoint {
- remote-endpoint = <&hdmi0_con>;
- };
- };
- port@2 {
- reg = <2>;
- rcar_dw_hdmi0_sound_in: endpoint {
- remote-endpoint = <&hdmi_sound_out>;
- };
- };
- };
- };
-
- hdmi0-out {
- compatible = "hdmi-connector";
- label = "HDMI0 OUT";
- type = "a";
-
- port {
- hdmi0_con: endpoint {
- remote-endpoint = <&rcar_dw_hdmi0_out>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
new file mode 100644
index 000000000000..0c9785c8db51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
@@ -0,0 +1,125 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car DWC HDMI TX Encoder
+
+maintainers:
+ - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - renesas,r8a774a1-hdmi # for RZ/G2M compatible HDMI TX
+ - renesas,r8a774b1-hdmi # for RZ/G2N compatible HDMI TX
+ - renesas,r8a774e1-hdmi # for RZ/G2H compatible HDMI TX
+ - renesas,r8a7795-hdmi # for R-Car H3 compatible HDMI TX
+ - renesas,r8a7796-hdmi # for R-Car M3-W compatible HDMI TX
+ - renesas,r8a77961-hdmi # for R-Car M3-W+ compatible HDMI TX
+ - renesas,r8a77965-hdmi # for R-Car M3-N compatible HDMI TX
+ - const: renesas,rcar-gen3-hdmi
+
+ reg-io-width:
+ const: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ maxItems: 2
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Parallel RGB input port
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: HDMI output port
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Sound input port
+
+ required:
+ - port@0
+ - port@1
+ - port@2
+
+ power-domains:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - interrupts
+ - ports
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/power/r8a7795-sysc.h>
+
+ hdmi@fead0000 {
+ compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
+ reg = <0xfead0000 0x10000>;
+ interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
+ clock-names = "iahb", "isfr";
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ dw_hdmi0_in: endpoint {
+ remote-endpoint = <&du_out_hdmi0>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ rcar_dw_hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi0_con>;
+ };
+ };
+ port@2 {
+ reg = <2>;
+ rcar_dw_hdmi0_sound_in: endpoint {
+ remote-endpoint = <&hdmi_sound_out>;
+ };
+ };
+ };
+ };
+
+ hdmi0-out {
+ compatible = "hdmi-connector";
+ label = "HDMI0 OUT";
+ type = "a";
+
+ port {
+ hdmi0_con: endpoint {
+ remote-endpoint = <&rcar_dw_hdmi0_out>;
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 094e52838542..318b694dba61 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5948,7 +5948,7 @@ L: dri-devel@lists.freedesktop.org
L: linux-renesas-soc@vger.kernel.org
S: Supported
T: git git://linuxtv.org/pinchartl/media drm/du/next
-F: Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+F: Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
F: Documentation/devicetree/bindings/display/bridge/renesas,lvds.yaml
F: Documentation/devicetree/bindings/display/renesas,du.yaml
F: drivers/gpu/drm/rcar-du/
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 3/7] dt-bindings: display: bridge: renesas, dw-hdmi: Convert binding to YAML
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Convert the Renesas R-Car DWC HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Use port instead of port-base
Changes since v2:
- Update MAINTAINERS
Changes since v1:
- Drop the part numbers in comments, only keep the SoC names
- Use unevaluatedProperties instead of additionalProperties
- Only specify maxItems for clocks and clock-names
- Drop reg, interrupts, #address-cells and #size-cells as they're
checked in the base schema
- Use one size and address cell in example
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
---
.../display/bridge/renesas,dw-hdmi.txt | 88 ------------
.../display/bridge/renesas,dw-hdmi.yaml | 125 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 126 insertions(+), 89 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
deleted file mode 100644
index 3f6072651182..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-Renesas Gen3 DWC HDMI TX Encoder
-================================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible : Shall contain one or more of
- - "renesas,r8a774a1-hdmi" for R8A774A1 (RZ/G2M) compatible HDMI TX
- - "renesas,r8a774b1-hdmi" for R8A774B1 (RZ/G2N) compatible HDMI TX
- - "renesas,r8a774e1-hdmi" for R8A774E1 (RZ/G2H) compatible HDMI TX
- - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
- - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX
- - "renesas,r8a77961-hdmi" for R8A77961 (R-Car M3-W+) compatible HDMI TX
- - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX
- - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 and RZ/G2 compatible
- HDMI TX
-
- When compatible with generic versions, nodes must list the SoC-specific
- version corresponding to the platform first, followed by the
- family-specific version.
-
-- reg: See dw_hdmi.txt.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have one port numbered 0
- corresponding to the video input of the controller and one port numbered 1
- corresponding to its HDMI output, and one port numbered 2 corresponding to
- sound input of the controller. Each port shall have a single endpoint.
-
-Optional properties:
-
-- power-domains: Shall reference the power domain that contains the DWC HDMI,
- if any.
-
-
-Example:
-
- hdmi0: hdmi@fead0000 {
- compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
- reg = <0 0xfead0000 0 0x10000>;
- interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
- clock-names = "iahb", "isfr";
- power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- dw_hdmi0_in: endpoint {
- remote-endpoint = <&du_out_hdmi0>;
- };
- };
- port@1 {
- reg = <1>;
- rcar_dw_hdmi0_out: endpoint {
- remote-endpoint = <&hdmi0_con>;
- };
- };
- port@2 {
- reg = <2>;
- rcar_dw_hdmi0_sound_in: endpoint {
- remote-endpoint = <&hdmi_sound_out>;
- };
- };
- };
- };
-
- hdmi0-out {
- compatible = "hdmi-connector";
- label = "HDMI0 OUT";
- type = "a";
-
- port {
- hdmi0_con: endpoint {
- remote-endpoint = <&rcar_dw_hdmi0_out>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
new file mode 100644
index 000000000000..0c9785c8db51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
@@ -0,0 +1,125 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car DWC HDMI TX Encoder
+
+maintainers:
+ - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - renesas,r8a774a1-hdmi # for RZ/G2M compatible HDMI TX
+ - renesas,r8a774b1-hdmi # for RZ/G2N compatible HDMI TX
+ - renesas,r8a774e1-hdmi # for RZ/G2H compatible HDMI TX
+ - renesas,r8a7795-hdmi # for R-Car H3 compatible HDMI TX
+ - renesas,r8a7796-hdmi # for R-Car M3-W compatible HDMI TX
+ - renesas,r8a77961-hdmi # for R-Car M3-W+ compatible HDMI TX
+ - renesas,r8a77965-hdmi # for R-Car M3-N compatible HDMI TX
+ - const: renesas,rcar-gen3-hdmi
+
+ reg-io-width:
+ const: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ maxItems: 2
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Parallel RGB input port
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: HDMI output port
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Sound input port
+
+ required:
+ - port@0
+ - port@1
+ - port@2
+
+ power-domains:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - interrupts
+ - ports
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/power/r8a7795-sysc.h>
+
+ hdmi@fead0000 {
+ compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
+ reg = <0xfead0000 0x10000>;
+ interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
+ clock-names = "iahb", "isfr";
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ dw_hdmi0_in: endpoint {
+ remote-endpoint = <&du_out_hdmi0>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ rcar_dw_hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi0_con>;
+ };
+ };
+ port@2 {
+ reg = <2>;
+ rcar_dw_hdmi0_sound_in: endpoint {
+ remote-endpoint = <&hdmi_sound_out>;
+ };
+ };
+ };
+ };
+
+ hdmi0-out {
+ compatible = "hdmi-connector";
+ label = "HDMI0 OUT";
+ type = "a";
+
+ port {
+ hdmi0_con: endpoint {
+ remote-endpoint = <&rcar_dw_hdmi0_out>;
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 094e52838542..318b694dba61 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5948,7 +5948,7 @@ L: dri-devel@lists.freedesktop.org
L: linux-renesas-soc@vger.kernel.org
S: Supported
T: git git://linuxtv.org/pinchartl/media drm/du/next
-F: Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+F: Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.yaml
F: Documentation/devicetree/bindings/display/bridge/renesas,lvds.yaml
F: Documentation/devicetree/bindings/display/renesas,du.yaml
F: drivers/gpu/drm/rcar-du/
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Convert the i.MX6 HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Use port instead of port-base
Changes since v1:
- Only specify maxItems for clocks
- Drop reg and interrupts as they're checked in the base schema
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
- Drop clock-names items, use maxItems only
---
.../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
.../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
2 files changed, 126 insertions(+), 65 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
new file mode 100644
index 000000000000..af7fe9c4d196
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6 DWC HDMI TX Encoder
+
+maintainers:
+ - Philipp Zabel <p.zabel@pengutronix.de>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: ../bridge/synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ enum:
+ - fsl,imx6dl-hdmi
+ - fsl,imx6q-hdmi
+
+ reg-io-width:
+ const: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ maxItems: 2
+
+ ddc-i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The HDMI DDC bus can be connected to either a system I2C master or the
+ functionally-reduced I2C master contained in the DWC HDMI. When connected
+ to a system I2C master this property contains a phandle to that I2C
+ master controller.
+
+ gpr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to the iomuxc-gpr region containing the HDMI multiplexer control
+ register.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description: |
+ This device has four video ports, corresponding to the four inputs of the
+ HDMI multiplexer. Each port shall have a single endpoint.
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: First input of the HDMI multiplexer
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Second input of the HDMI multiplexer
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Third input of the HDMI multiplexer
+
+ port@3:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Fourth input of the HDMI multiplexer
+
+ anyOf:
+ - required:
+ - port@0
+ - required:
+ - port@1
+ - required:
+ - port@2
+ - required:
+ - port@3
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - gpr
+ - interrupts
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+
+ hdmi: hdmi@120000 {
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>,
+ <&clks IMX6QDL_CLK_HDMI_ISFR>;
+ clock-names = "iahb", "isfr";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/display/imx/hdmi.txt b/Documentation/devicetree/bindings/display/imx/hdmi.txt
deleted file mode 100644
index 6d021e71c9cf..000000000000
--- a/Documentation/devicetree/bindings/display/imx/hdmi.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-Freescale i.MX6 DWC HDMI TX Encoder
-===================================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible : Shall be one of "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
-- reg: See dw_hdmi.txt.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have between one and four ports,
- numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer.
- Each port shall have a single endpoint.
-- gpr : Shall contain a phandle to the iomuxc-gpr region containing the HDMI
- multiplexer control register.
-
-Optional properties
-
-- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
- or the functionally-reduced I2C master contained in the DWC HDMI. When
- connected to a system I2C master this property contains a phandle to that
- I2C master controller.
-
-
-Example:
-
- gpr: iomuxc-gpr@20e0000 {
- /* ... */
- };
-
- hdmi: hdmi@120000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6q-hdmi";
- reg = <0x00120000 0x9000>;
- interrupts = <0 115 0x04>;
- gpr = <&gpr>;
- clocks = <&clks 123>, <&clks 124>;
- clock-names = "iahb", "isfr";
- ddc-i2c-bus = <&i2c2>;
-
- port@0 {
- reg = <0>;
-
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
- };
- };
- };
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Convert the i.MX6 HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v3:
- Use port instead of port-base
Changes since v1:
- Only specify maxItems for clocks
- Drop reg and interrupts as they're checked in the base schema
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
- Drop clock-names items, use maxItems only
---
.../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
.../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
2 files changed, 126 insertions(+), 65 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
new file mode 100644
index 000000000000..af7fe9c4d196
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6 DWC HDMI TX Encoder
+
+maintainers:
+ - Philipp Zabel <p.zabel@pengutronix.de>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: ../bridge/synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ enum:
+ - fsl,imx6dl-hdmi
+ - fsl,imx6q-hdmi
+
+ reg-io-width:
+ const: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ maxItems: 2
+
+ ddc-i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The HDMI DDC bus can be connected to either a system I2C master or the
+ functionally-reduced I2C master contained in the DWC HDMI. When connected
+ to a system I2C master this property contains a phandle to that I2C
+ master controller.
+
+ gpr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to the iomuxc-gpr region containing the HDMI multiplexer control
+ register.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description: |
+ This device has four video ports, corresponding to the four inputs of the
+ HDMI multiplexer. Each port shall have a single endpoint.
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: First input of the HDMI multiplexer
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Second input of the HDMI multiplexer
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Third input of the HDMI multiplexer
+
+ port@3:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Fourth input of the HDMI multiplexer
+
+ anyOf:
+ - required:
+ - port@0
+ - required:
+ - port@1
+ - required:
+ - port@2
+ - required:
+ - port@3
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - gpr
+ - interrupts
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+
+ hdmi: hdmi@120000 {
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>,
+ <&clks IMX6QDL_CLK_HDMI_ISFR>;
+ clock-names = "iahb", "isfr";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/display/imx/hdmi.txt b/Documentation/devicetree/bindings/display/imx/hdmi.txt
deleted file mode 100644
index 6d021e71c9cf..000000000000
--- a/Documentation/devicetree/bindings/display/imx/hdmi.txt
+++ /dev/null
@@ -1,65 +0,0 @@
-Freescale i.MX6 DWC HDMI TX Encoder
-===================================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible : Shall be one of "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
-- reg: See dw_hdmi.txt.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have between one and four ports,
- numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer.
- Each port shall have a single endpoint.
-- gpr : Shall contain a phandle to the iomuxc-gpr region containing the HDMI
- multiplexer control register.
-
-Optional properties
-
-- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
- or the functionally-reduced I2C master contained in the DWC HDMI. When
- connected to a system I2C master this property contains a phandle to that
- I2C master controller.
-
-
-Example:
-
- gpr: iomuxc-gpr@20e0000 {
- /* ... */
- };
-
- hdmi: hdmi@120000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6q-hdmi";
- reg = <0x00120000 0x9000>;
- interrupts = <0 115 0x04>;
- gpr = <&gpr>;
- clocks = <&clks 123>, <&clks 124>;
- clock-names = "iahb", "isfr";
- ddc-i2c-bus = <&i2c2>;
-
- port@0 {
- reg = <0>;
-
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
- };
- };
- };
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 5/7] dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Convert the Rockchip HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
Changes since v3:
- Replace endpoint-base with endpoint
Changes since v2:
- Use Mark's @gmail.com e-mail address as the @rock-chips.com address
bounces
Changes since v1:
- Drop pinctrl-0 and pinctrl-1
- Use unevaluatedProperties instead of additionalProperties
- Drop reg and interrupts as they're checked in the base schema
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
- Tidy up clock names
---
.../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
.../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
2 files changed, 156 insertions(+), 74 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
deleted file mode 100644
index 3d32ce137e7f..000000000000
--- a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
+++ /dev/null
@@ -1,74 +0,0 @@
-Rockchip DWC HDMI TX Encoder
-============================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible: should be one of the following:
- "rockchip,rk3228-dw-hdmi"
- "rockchip,rk3288-dw-hdmi"
- "rockchip,rk3328-dw-hdmi"
- "rockchip,rk3399-dw-hdmi"
-- reg: See dw_hdmi.txt.
-- reg-io-width: See dw_hdmi.txt. Shall be 4.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have a single port numbered 0
- corresponding to the video input of the controller. The port shall have two
- endpoints, numbered 0 and 1, connected respectively to the vopb and vopl.
-- rockchip,grf: Shall reference the GRF to mux vopl/vopb.
-
-Optional properties
-
-- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
- or the functionally-reduced I2C master contained in the DWC HDMI. When
- connected to a system I2C master this property contains a phandle to that
- I2C master controller.
-- clock-names: See dw_hdmi.txt. The "cec" clock is optional.
-- clock-names: May contain "cec" as defined in dw_hdmi.txt.
-- clock-names: May contain "grf", power for grf io.
-- clock-names: May contain "vpll", external clock for some hdmi phy.
-- phys: from general PHY binding: the phandle for the PHY device.
-- phy-names: Should be "hdmi" if phys references an external phy.
-
-Optional pinctrl entry:
-- If you have both a "unwedge" and "default" pinctrl entry, dw_hdmi
- will switch to the unwedge pinctrl state for 10ms if it ever gets an
- i2c timeout. It's intended that this unwedge pinctrl entry will
- cause the SDA line to be driven low to work around a hardware
- errata.
-
-Example:
-
-hdmi: hdmi@ff980000 {
- compatible = "rockchip,rk3288-dw-hdmi";
- reg = <0xff980000 0x20000>;
- reg-io-width = <4>;
- ddc-i2c-bus = <&i2c5>;
- rockchip,grf = <&grf>;
- interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
- clock-names = "iahb", "isfr";
- ports {
- hdmi_in: port {
- #address-cells = <1>;
- #size-cells = <0>;
- hdmi_in_vopb: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&vopb_out_hdmi>;
- };
- hdmi_in_vopl: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&vopl_out_hdmi>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
new file mode 100644
index 000000000000..75cd9c686e98
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/rockchip/rockchip,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip DWC HDMI TX Encoder
+
+maintainers:
+ - Mark Yao <markyao0591@gmail.com>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: ../bridge/synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk3228-dw-hdmi
+ - rockchip,rk3288-dw-hdmi
+ - rockchip,rk3328-dw-hdmi
+ - rockchip,rk3399-dw-hdmi
+
+ reg-io-width:
+ const: 4
+
+ clocks:
+ minItems: 2
+ maxItems: 5
+ items:
+ - {}
+ - {}
+ # The next three clocks are all optional, but shall be specified in this
+ # order when present.
+ - description: The HDMI CEC controller main clock
+ - description: Power for GRF IO
+ - description: External clock for some HDMI PHY
+
+ clock-names:
+ minItems: 2
+ maxItems: 5
+ items:
+ - {}
+ - {}
+ - enum:
+ - cec
+ - grf
+ - vpll
+ - enum:
+ - grf
+ - vpll
+ - const: vpll
+
+ ddc-i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The HDMI DDC bus can be connected to either a system I2C master or the
+ functionally-reduced I2C master contained in the DWC HDMI. When connected
+ to a system I2C master this property contains a phandle to that I2C
+ master controller.
+
+ phys:
+ maxItems: 1
+ description: The HDMI PHY
+
+ phy-names:
+ const: hdmi
+
+ pinctrl-names:
+ description:
+ The unwedge pinctrl entry shall drive the DDC SDA line low. This is
+ intended to work around a hardware errata that can cause the DDC I2C
+ bus to be wedged.
+ items:
+ - const: default
+ - const: unwedge
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: Input of the DWC HDMI TX
+
+ properties:
+ endpoint@0:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description: Connection to the VOPB
+
+ endpoint@1:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description: Connection to the VOPL
+
+ required:
+ - endpoint@0
+ - endpoint@1
+
+ required:
+ - port
+
+ rockchip,grf:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to the GRF to mux vopl/vopb.
+
+required:
+ - compatible
+ - reg
+ - reg-io-width
+ - clocks
+ - clock-names
+ - interrupts
+ - ports
+ - rockchip,grf
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/rk3288-cru.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ hdmi: hdmi@ff980000 {
+ compatible = "rockchip,rk3288-dw-hdmi";
+ reg = <0xff980000 0x20000>;
+ reg-io-width = <4>;
+ ddc-i2c-bus = <&i2c5>;
+ rockchip,grf = <&grf>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
+ clock-names = "iahb", "isfr";
+
+ ports {
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_hdmi>;
+ };
+ hdmi_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_hdmi>;
+ };
+ };
+ };
+ };
+
+...
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 5/7] dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Convert the Rockchip HDMI TX text binding to YAML.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
Changes since v3:
- Replace endpoint-base with endpoint
Changes since v2:
- Use Mark's @gmail.com e-mail address as the @rock-chips.com address
bounces
Changes since v1:
- Drop pinctrl-0 and pinctrl-1
- Use unevaluatedProperties instead of additionalProperties
- Drop reg and interrupts as they're checked in the base schema
- Rebase on top of OF graph schema, dropped redundant properties
- Fix identation for enum entries
- Tidy up clock names
---
.../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
.../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
2 files changed, 156 insertions(+), 74 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
deleted file mode 100644
index 3d32ce137e7f..000000000000
--- a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
+++ /dev/null
@@ -1,74 +0,0 @@
-Rockchip DWC HDMI TX Encoder
-============================
-
-The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
-with a companion PHY IP.
-
-These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
-Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
-following device-specific properties.
-
-
-Required properties:
-
-- compatible: should be one of the following:
- "rockchip,rk3228-dw-hdmi"
- "rockchip,rk3288-dw-hdmi"
- "rockchip,rk3328-dw-hdmi"
- "rockchip,rk3399-dw-hdmi"
-- reg: See dw_hdmi.txt.
-- reg-io-width: See dw_hdmi.txt. Shall be 4.
-- interrupts: HDMI interrupt number
-- clocks: See dw_hdmi.txt.
-- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
-- ports: See dw_hdmi.txt. The DWC HDMI shall have a single port numbered 0
- corresponding to the video input of the controller. The port shall have two
- endpoints, numbered 0 and 1, connected respectively to the vopb and vopl.
-- rockchip,grf: Shall reference the GRF to mux vopl/vopb.
-
-Optional properties
-
-- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
- or the functionally-reduced I2C master contained in the DWC HDMI. When
- connected to a system I2C master this property contains a phandle to that
- I2C master controller.
-- clock-names: See dw_hdmi.txt. The "cec" clock is optional.
-- clock-names: May contain "cec" as defined in dw_hdmi.txt.
-- clock-names: May contain "grf", power for grf io.
-- clock-names: May contain "vpll", external clock for some hdmi phy.
-- phys: from general PHY binding: the phandle for the PHY device.
-- phy-names: Should be "hdmi" if phys references an external phy.
-
-Optional pinctrl entry:
-- If you have both a "unwedge" and "default" pinctrl entry, dw_hdmi
- will switch to the unwedge pinctrl state for 10ms if it ever gets an
- i2c timeout. It's intended that this unwedge pinctrl entry will
- cause the SDA line to be driven low to work around a hardware
- errata.
-
-Example:
-
-hdmi: hdmi@ff980000 {
- compatible = "rockchip,rk3288-dw-hdmi";
- reg = <0xff980000 0x20000>;
- reg-io-width = <4>;
- ddc-i2c-bus = <&i2c5>;
- rockchip,grf = <&grf>;
- interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
- clock-names = "iahb", "isfr";
- ports {
- hdmi_in: port {
- #address-cells = <1>;
- #size-cells = <0>;
- hdmi_in_vopb: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&vopb_out_hdmi>;
- };
- hdmi_in_vopl: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&vopl_out_hdmi>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
new file mode 100644
index 000000000000..75cd9c686e98
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/rockchip/rockchip,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip DWC HDMI TX Encoder
+
+maintainers:
+ - Mark Yao <markyao0591@gmail.com>
+
+description: |
+ The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+ with a companion PHY IP.
+
+allOf:
+ - $ref: ../bridge/synopsys,dw-hdmi.yaml#
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk3228-dw-hdmi
+ - rockchip,rk3288-dw-hdmi
+ - rockchip,rk3328-dw-hdmi
+ - rockchip,rk3399-dw-hdmi
+
+ reg-io-width:
+ const: 4
+
+ clocks:
+ minItems: 2
+ maxItems: 5
+ items:
+ - {}
+ - {}
+ # The next three clocks are all optional, but shall be specified in this
+ # order when present.
+ - description: The HDMI CEC controller main clock
+ - description: Power for GRF IO
+ - description: External clock for some HDMI PHY
+
+ clock-names:
+ minItems: 2
+ maxItems: 5
+ items:
+ - {}
+ - {}
+ - enum:
+ - cec
+ - grf
+ - vpll
+ - enum:
+ - grf
+ - vpll
+ - const: vpll
+
+ ddc-i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The HDMI DDC bus can be connected to either a system I2C master or the
+ functionally-reduced I2C master contained in the DWC HDMI. When connected
+ to a system I2C master this property contains a phandle to that I2C
+ master controller.
+
+ phys:
+ maxItems: 1
+ description: The HDMI PHY
+
+ phy-names:
+ const: hdmi
+
+ pinctrl-names:
+ description:
+ The unwedge pinctrl entry shall drive the DDC SDA line low. This is
+ intended to work around a hardware errata that can cause the DDC I2C
+ bus to be wedged.
+ items:
+ - const: default
+ - const: unwedge
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: Input of the DWC HDMI TX
+
+ properties:
+ endpoint@0:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description: Connection to the VOPB
+
+ endpoint@1:
+ $ref: /schemas/graph.yaml#/properties/endpoint
+ description: Connection to the VOPL
+
+ required:
+ - endpoint@0
+ - endpoint@1
+
+ required:
+ - port
+
+ rockchip,grf:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to the GRF to mux vopl/vopb.
+
+required:
+ - compatible
+ - reg
+ - reg-io-width
+ - clocks
+ - clock-names
+ - interrupts
+ - ports
+ - rockchip,grf
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/rk3288-cru.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ hdmi: hdmi@ff980000 {
+ compatible = "rockchip,rk3288-dw-hdmi";
+ reg = <0xff980000 0x20000>;
+ reg-io-width = <4>;
+ ddc-i2c-bus = <&i2c5>;
+ rockchip,grf = <&grf>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>;
+ clock-names = "iahb", "isfr";
+
+ ports {
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_hdmi>;
+ };
+ hdmi_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_hdmi>;
+ };
+ };
+ };
+ };
+
+...
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 6/7] dt-bindings: display: sun8i-a83t-dw-hdmi: Reference dw-hdmi YAML schema
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
Replace the reference to the DWC HDMI text DT binding with a reference
to the YAML equivalent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
.../bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
index fa4769a0b26e..5cbf655c3a07 100644
--- a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
+++ b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
@@ -12,8 +12,8 @@ description: |
and CEC.
These DT bindings follow the Synopsys DWC HDMI TX bindings defined
- in Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with
- the following device-specific properties.
+ in bridge/synopsys,dw-hdmi.yaml with the following device-specific
+ properties.
maintainers:
- Chen-Yu Tsai <wens@csie.org>
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 6/7] dt-bindings: display: sun8i-a83t-dw-hdmi: Reference dw-hdmi YAML schema
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
Replace the reference to the DWC HDMI text DT binding with a reference
to the YAML equivalent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
.../bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
index fa4769a0b26e..5cbf655c3a07 100644
--- a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
+++ b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml
@@ -12,8 +12,8 @@ description: |
and CEC.
These DT bindings follow the Synopsys DWC HDMI TX bindings defined
- in Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with
- the following device-specific properties.
+ in bridge/synopsys,dw-hdmi.yaml with the following device-specific
+ properties.
maintainers:
- Chen-Yu Tsai <wens@csie.org>
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 7/7] dt-bindings: display: bridge: Remove deprecated dw_hdmi.txt
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 6:44 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring,
Mark Yao, Philipp Zabel
dw_hdmi.txt has been replaced with synopsys,dw-hdmi.yaml, and all
references to the old file have been converted. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/display/bridge/dw_hdmi.txt | 33 -------------------
1 file changed, 33 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
deleted file mode 100644
index 33bf981fbe33..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
+++ /dev/null
@@ -1,33 +0,0 @@
-Synopsys DesignWare HDMI TX Encoder
-===================================
-
-This document defines device tree properties for the Synopsys DesignWare HDMI
-TX Encoder (DWC HDMI TX). It doesn't constitue a device tree binding
-specification by itself but is meant to be referenced by platform-specific
-device tree bindings.
-
-When referenced from platform device tree bindings the properties defined in
-this document are defined as follows. The platform device tree bindings are
-responsible for defining whether each property is required or optional.
-
-- reg: Memory mapped base address and length of the DWC HDMI TX registers.
-
-- reg-io-width: Width of the registers specified by the reg property. The
- value is expressed in bytes and must be equal to 1 or 4 if specified. The
- register width defaults to 1 if the property is not present.
-
-- interrupts: Reference to the DWC HDMI TX interrupt.
-
-- clocks: References to all the clocks specified in the clock-names property
- as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt.
-
-- clock-names: The DWC HDMI TX uses the following clocks.
-
- - "iahb" is the bus clock for either AHB and APB (mandatory).
- - "isfr" is the internal register configuration clock (mandatory).
- - "cec" is the HDMI CEC controller main clock (optional).
-
-- ports: The connectivity of the DWC HDMI TX with the rest of the system is
- expressed in using ports as specified in the device graph bindings defined
- in Documentation/devicetree/bindings/graph.txt. The numbering of the ports
- is platform-specific.
--
Regards,
Laurent Pinchart
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v4 7/7] dt-bindings: display: bridge: Remove deprecated dw_hdmi.txt
@ 2021-01-14 6:44 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 6:44 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, Sandy Huang, linux-renesas-soc, Rob Herring, Mark Yao
dw_hdmi.txt has been replaced with synopsys,dw-hdmi.yaml, and all
references to the old file have been converted. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/display/bridge/dw_hdmi.txt | 33 -------------------
1 file changed, 33 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
deleted file mode 100644
index 33bf981fbe33..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt
+++ /dev/null
@@ -1,33 +0,0 @@
-Synopsys DesignWare HDMI TX Encoder
-===================================
-
-This document defines device tree properties for the Synopsys DesignWare HDMI
-TX Encoder (DWC HDMI TX). It doesn't constitue a device tree binding
-specification by itself but is meant to be referenced by platform-specific
-device tree bindings.
-
-When referenced from platform device tree bindings the properties defined in
-this document are defined as follows. The platform device tree bindings are
-responsible for defining whether each property is required or optional.
-
-- reg: Memory mapped base address and length of the DWC HDMI TX registers.
-
-- reg-io-width: Width of the registers specified by the reg property. The
- value is expressed in bytes and must be equal to 1 or 4 if specified. The
- register width defaults to 1 if the property is not present.
-
-- interrupts: Reference to the DWC HDMI TX interrupt.
-
-- clocks: References to all the clocks specified in the clock-names property
- as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt.
-
-- clock-names: The DWC HDMI TX uses the following clocks.
-
- - "iahb" is the bus clock for either AHB and APB (mandatory).
- - "isfr" is the internal register configuration clock (mandatory).
- - "cec" is the HDMI CEC controller main clock (optional).
-
-- ports: The connectivity of the DWC HDMI TX with the rest of the system is
- expressed in using ports as specified in the device graph bindings defined
- in Documentation/devicetree/bindings/graph.txt. The numbering of the ports
- is platform-specific.
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-14 8:17 ` Philipp Zabel
-1 siblings, 0 replies; 22+ messages in thread
From: Philipp Zabel @ 2021-01-14 8:17 UTC (permalink / raw)
To: Laurent Pinchart, dri-devel
Cc: devicetree, linux-renesas-soc, Sandy Huang, Rob Herring, Mark Yao
On Thu, 2021-01-14 at 08:44 +0200, Laurent Pinchart wrote:
> Convert the i.MX6 HDMI TX text binding to YAML.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes since v3:
>
> - Use port instead of port-base
>
> Changes since v1:
>
> - Only specify maxItems for clocks
> - Drop reg and interrupts as they're checked in the base schema
> - Rebase on top of OF graph schema, dropped redundant properties
> - Fix identation for enum entries
> - Drop clock-names items, use maxItems only
> ---
> .../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
> .../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
> 2 files changed, 126 insertions(+), 65 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> new file mode 100644
> index 000000000000..af7fe9c4d196
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> @@ -0,0 +1,126 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale i.MX6 DWC HDMI TX Encoder
> +
> +maintainers:
> + - Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
regards
Philipp
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
@ 2021-01-14 8:17 ` Philipp Zabel
0 siblings, 0 replies; 22+ messages in thread
From: Philipp Zabel @ 2021-01-14 8:17 UTC (permalink / raw)
To: Laurent Pinchart, dri-devel
Cc: linux-renesas-soc, devicetree, Rob Herring, Sandy Huang, Mark Yao
On Thu, 2021-01-14 at 08:44 +0200, Laurent Pinchart wrote:
> Convert the i.MX6 HDMI TX text binding to YAML.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes since v3:
>
> - Use port instead of port-base
>
> Changes since v1:
>
> - Only specify maxItems for clocks
> - Drop reg and interrupts as they're checked in the base schema
> - Rebase on top of OF graph schema, dropped redundant properties
> - Fix identation for enum entries
> - Drop clock-names items, use maxItems only
> ---
> .../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
> .../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
> 2 files changed, 126 insertions(+), 65 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> new file mode 100644
> index 000000000000..af7fe9c4d196
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> @@ -0,0 +1,126 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale i.MX6 DWC HDMI TX Encoder
> +
> +maintainers:
> + - Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
regards
Philipp
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
2021-01-14 8:17 ` Philipp Zabel
@ 2021-01-14 9:42 ` Laurent Pinchart
-1 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 9:42 UTC (permalink / raw)
To: Philipp Zabel
Cc: Laurent Pinchart, dri-devel, devicetree, linux-renesas-soc,
Sandy Huang, Rob Herring, Mark Yao
Hi Philipp,
On Thu, Jan 14, 2021 at 09:17:47AM +0100, Philipp Zabel wrote:
> On Thu, 2021-01-14 at 08:44 +0200, Laurent Pinchart wrote:
> > Convert the i.MX6 HDMI TX text binding to YAML.
> >
> > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > ---
> > Changes since v3:
> >
> > - Use port instead of port-base
> >
> > Changes since v1:
> >
> > - Only specify maxItems for clocks
> > - Drop reg and interrupts as they're checked in the base schema
> > - Rebase on top of OF graph schema, dropped redundant properties
> > - Fix identation for enum entries
> > - Drop clock-names items, use maxItems only
> > ---
> > .../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
> > .../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
> > 2 files changed, 126 insertions(+), 65 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > new file mode 100644
> > index 000000000000..af7fe9c4d196
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > @@ -0,0 +1,126 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Freescale i.MX6 DWC HDMI TX Encoder
> > +
> > +maintainers:
> > + - Philipp Zabel <p.zabel@pengutronix.de>
>
> Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Very appreciated, thank you.
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v4 4/7] dt-bindings: display: imx: hdmi: Convert binding to YAML
@ 2021-01-14 9:42 ` Laurent Pinchart
0 siblings, 0 replies; 22+ messages in thread
From: Laurent Pinchart @ 2021-01-14 9:42 UTC (permalink / raw)
To: Philipp Zabel
Cc: devicetree, Laurent Pinchart, Sandy Huang, dri-devel,
linux-renesas-soc, Rob Herring, Mark Yao
Hi Philipp,
On Thu, Jan 14, 2021 at 09:17:47AM +0100, Philipp Zabel wrote:
> On Thu, 2021-01-14 at 08:44 +0200, Laurent Pinchart wrote:
> > Convert the i.MX6 HDMI TX text binding to YAML.
> >
> > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > ---
> > Changes since v3:
> >
> > - Use port instead of port-base
> >
> > Changes since v1:
> >
> > - Only specify maxItems for clocks
> > - Drop reg and interrupts as they're checked in the base schema
> > - Rebase on top of OF graph schema, dropped redundant properties
> > - Fix identation for enum entries
> > - Drop clock-names items, use maxItems only
> > ---
> > .../bindings/display/imx/fsl,imx6-hdmi.yaml | 126 ++++++++++++++++++
> > .../devicetree/bindings/display/imx/hdmi.txt | 65 ---------
> > 2 files changed, 126 insertions(+), 65 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > delete mode 100644 Documentation/devicetree/bindings/display/imx/hdmi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > new file mode 100644
> > index 000000000000..af7fe9c4d196
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml
> > @@ -0,0 +1,126 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Freescale i.MX6 DWC HDMI TX Encoder
> > +
> > +maintainers:
> > + - Philipp Zabel <p.zabel@pengutronix.de>
>
> Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Very appreciated, thank you.
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v4 5/7] dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
2021-01-14 6:44 ` Laurent Pinchart
@ 2021-01-15 16:50 ` Rob Herring
-1 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2021-01-15 16:50 UTC (permalink / raw)
To: Laurent Pinchart
Cc: Rob Herring, dri-devel, linux-renesas-soc, Mark Yao, devicetree,
Sandy Huang
On Thu, 14 Jan 2021 08:44:35 +0200, Laurent Pinchart wrote:
> Convert the Rockchip HDMI TX text binding to YAML.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> ---
> Changes since v3:
>
> - Replace endpoint-base with endpoint
>
> Changes since v2:
>
> - Use Mark's @gmail.com e-mail address as the @rock-chips.com address
> bounces
>
> Changes since v1:
>
> - Drop pinctrl-0 and pinctrl-1
> - Use unevaluatedProperties instead of additionalProperties
> - Drop reg and interrupts as they're checked in the base schema
> - Rebase on top of OF graph schema, dropped redundant properties
> - Fix identation for enum entries
> - Tidy up clock names
> ---
> .../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
> .../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
> 2 files changed, 156 insertions(+), 74 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
> create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v4 5/7] dt-bindings: display: rockchip: dw-hdmi: Convert binding to YAML
@ 2021-01-15 16:50 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2021-01-15 16:50 UTC (permalink / raw)
To: Laurent Pinchart
Cc: devicetree, Sandy Huang, dri-devel, linux-renesas-soc,
Rob Herring, Mark Yao
On Thu, 14 Jan 2021 08:44:35 +0200, Laurent Pinchart wrote:
> Convert the Rockchip HDMI TX text binding to YAML.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> ---
> Changes since v3:
>
> - Replace endpoint-base with endpoint
>
> Changes since v2:
>
> - Use Mark's @gmail.com e-mail address as the @rock-chips.com address
> bounces
>
> Changes since v1:
>
> - Drop pinctrl-0 and pinctrl-1
> - Use unevaluatedProperties instead of additionalProperties
> - Drop reg and interrupts as they're checked in the base schema
> - Rebase on top of OF graph schema, dropped redundant properties
> - Fix identation for enum entries
> - Tidy up clock names
> ---
> .../display/rockchip/dw_hdmi-rockchip.txt | 74 ---------
> .../display/rockchip/rockchip,dw-hdmi.yaml | 156 ++++++++++++++++++
> 2 files changed, 156 insertions(+), 74 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
> create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,dw-hdmi.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2021-01-15 16:51 UTC | newest]
Thread overview: 22+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-01-14 6:44 [PATCH v4 0/7] dt-bindings: display: Convert DWC HDMI TX bindings to YAML Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 1/7] ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 2/7] dt-bindings: display: bridge: Add YAML schema for Synopsys DW-HDMI Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 3/7] dt-bindings: display: bridge: renesas,dw-hdmi: Convert binding to YAML Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 3/7] dt-bindings: display: bridge: renesas, dw-hdmi: " Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 4/7] dt-bindings: display: imx: hdmi: " Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-14 8:17 ` Philipp Zabel
2021-01-14 8:17 ` Philipp Zabel
2021-01-14 9:42 ` Laurent Pinchart
2021-01-14 9:42 ` Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 5/7] dt-bindings: display: rockchip: dw-hdmi: " Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-15 16:50 ` Rob Herring
2021-01-15 16:50 ` Rob Herring
2021-01-14 6:44 ` [PATCH v4 6/7] dt-bindings: display: sun8i-a83t-dw-hdmi: Reference dw-hdmi YAML schema Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
2021-01-14 6:44 ` [PATCH v4 7/7] dt-bindings: display: bridge: Remove deprecated dw_hdmi.txt Laurent Pinchart
2021-01-14 6:44 ` Laurent Pinchart
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.