[PATCH v2 0/7] devicetree fixes for Protonic and Plymovent boards

[PATCH v2 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

changes v2:
- imx6dl-prtvt7: remove touchscreen-inverted-*

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 74 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 81 insertions(+), 13 deletions(-)

-- 
2.30.0

[PATCH v2 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

changes v2:
- imx6dl-prtvt7: remove touchscreen-inverted-*

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 74 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 81 insertions(+), 13 deletions(-)

-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 0/7] devicetree fixes for Protonic and Plymovent boards

[Oleksij Rempel]

changes v2:
- imx6dl-prtvt7: remove touchscreen-inverted-*

Oleksij Rempel (7):
  dt-bindings: display: simple: add Innolux G070Y2-T02 panel
  drm: panel-simple: Add support for the Innolux G070Y2-T02 panel
  ARM: dts: imx6dl-prtvt7: Add display and panel nodes
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

 .../bindings/display/panel/panel-simple.yaml  |  2 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           |  2 -
 arch/arm/boot/dts/imx6dl-prtvt7.dts           | 74 ++++++++++++++++---
 drivers/gpu/drm/panel/panel-simple.c          | 16 ++++
 4 files changed, 81 insertions(+), 13 deletions(-)

-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0

[PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
TFT LCD panel with TTL interface and a backlight unit.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 3207608d1178..f7a1465313db 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -152,6 +152,8 @@ properties:
       - innolux,at070tn92
         # Innolux G070Y2-L01 7" WVGA (800x480) TFT LCD panel
       - innolux,g070y2-l01
+        # Innolux G070Y2-T02 7" WVGA (800x480) TFT LCD TTL panel
+      - innolux,g070y2-t02
         # Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel
       - innolux,g101ice-l01
         # Innolux Corporation 12.1" WXGA (1280x800) TFT LCD panel
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Rob Herring]

On Thu, 21 Jan 2021 07:11:35 +0100, Oleksij Rempel wrote:
> Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
> TFT LCD panel with TTL interface and a backlight unit.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Rob Herring]

On Thu, 21 Jan 2021 07:11:35 +0100, Oleksij Rempel wrote:
> Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
> TFT LCD panel with TTL interface and a backlight unit.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 1/7] dt-bindings: display: simple: add Innolux G070Y2-T02 panel

[Rob Herring]

On Thu, 21 Jan 2021 07:11:35 +0100, Oleksij Rempel wrote:
> Add binding for the Innolux G070Y2-T02 panel. It is 7" WVGA (800x480)
> TFT LCD panel with TTL interface and a backlight unit.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  .../devicetree/bindings/display/panel/panel-simple.yaml         | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0

[PATCH v2 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 2/7] drm: panel-simple: Add support for the Innolux G070Y2-T02 panel

[Oleksij Rempel]

Add compatible and timings for the Innolux G070Y2-T02 panel. It is 7"
WVGA (800x480) TFT LCD panel with TTL interface and a backlight unit.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/gpu/drm/panel/panel-simple.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index 41bbec72b2da..14996ca264f3 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -2149,6 +2149,19 @@ static const struct panel_desc innolux_g070y2_l01 = {
 	.connector_type = DRM_MODE_CONNECTOR_LVDS,
 };
 
+static const struct panel_desc innolux_g070y2_t02 = {
+	.modes = &innolux_at070tn92_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,
+		.height = 92,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+};
+
 static const struct display_timing innolux_g101ice_l01_timing = {
 	.pixelclock = { 60400000, 71100000, 74700000 },
 	.hactive = { 1280, 1280, 1280 },
@@ -4135,6 +4148,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "innolux,g070y2-l01",
 		.data = &innolux_g070y2_l01,
+	}, {
+		.compatible = "innolux,g070y2-t02",
+		.data = &innolux_g070y2_t02,
 	}, {
 		.compatible = "innolux,g101ice-l01",
 		.data = &innolux_g101ice_l01
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0

[PATCH v2 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 3/7] ARM: dts: imx6dl-prtvt7: Add display and panel nodes

[Oleksij Rempel]

Add Innolux G070Y2-T02 panel to the Protonic VT7 board.

Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index ae6da241f13e..d9cb1e41cc10 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -31,6 +31,30 @@ backlight_lcd: backlight-lcd {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -138,6 +162,18 @@ led-debug0 {
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,6 +185,13 @@ reg_bl_12v0: regulator-bl-12v0 {
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -260,6 +303,10 @@ &ipu1 {
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
 &pwm1 {
 	#pwm-cells = <2>;
 	pinctrl-names = "default";
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..836026a0e219 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,21 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <4095>;
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0

[PATCH v2 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..836026a0e219 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,21 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <4095>;
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 4/7] ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node

[Oleksij Rempel]

Add touchscreen support to the Protonic VT7 board.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index d9cb1e41cc10..836026a0e219 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -266,6 +266,21 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <4095>;
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+		wakeup-source;
+	};
 };
 
 &i2c1 {
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 836026a0e219..8a1491975da8 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -362,12 +359,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0

[PATCH v2 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 836026a0e219..8a1491975da8 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -362,12 +359,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 5/7] ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio

[Oleksij Rempel]

The backlight power is controlled through the reg_bl_12v0 regulator.

Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 836026a0e219..8a1491975da8 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 500000>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	display {
@@ -362,12 +359,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 8a1491975da8..83b461eb33a2 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -320,7 +320,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0

[PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 8a1491975da8..83b461eb33a2 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -320,7 +320,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-prtvt7.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 8a1491975da8..83b461eb33a2 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -21,7 +21,7 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
@@ -320,7 +320,6 @@ &ipu1_di0_disp0 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Fabio Estevam]

Hi Oleksij,

On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> At some point PWM cell count was changed, but it didn't triggered any

It changed in this commit:

commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date:   Fri Jul 10 07:19:37 2020 +0200

    ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files

    The imx-pwm driver supports 3 cells and this is the more flexible setting.
    So use it by default and overwrite it back to two for the files that
    reference the PWMs with just 2 cells to minimize changes.

    This allows to drop explicit setting to 3 cells for the boards that already
    depend on this. The boards that are now using 2 cells explicitly can be
    converted to 3 individually.

    Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
    Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Fabio Estevam]

Hi Oleksij,

On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> At some point PWM cell count was changed, but it didn't triggered any

It changed in this commit:

commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date:   Fri Jul 10 07:19:37 2020 +0200

    ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files

    The imx-pwm driver supports 3 cells and this is the more flexible setting.
    So use it by default and overwrite it back to two for the files that
    reference the PWMs with just 2 cells to minimize changes.

    This allows to drop explicit setting to 3 cells for the boards that already
    depend on this. The boards that are now using 2 cells explicitly can be
    converted to 3 individually.

    Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
    Signed-off-by: Shawn Guo <shawnguo@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Fabio Estevam]

Hi Oleksij,

On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> At some point PWM cell count was changed, but it didn't triggered any

It changed in this commit:

commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date:   Fri Jul 10 07:19:37 2020 +0200

    ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files

    The imx-pwm driver supports 3 cells and this is the more flexible setting.
    So use it by default and overwrite it back to two for the files that
    reference the PWMs with just 2 cells to minimize changes.

    This allows to drop explicit setting to 3 cells for the boards that already
    depend on this. The boards that are now using 2 cells explicitly can be
    converted to 3 individually.

    Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
    Signed-off-by: Shawn Guo <shawnguo@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

On Thu, Jan 21, 2021 at 11:17:42AM -0300, Fabio Estevam wrote:
> Hi Oleksij,
> 
> On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> >
> > At some point PWM cell count was changed, but it didn't triggered any
> 
> It changed in this commit:
> 
> commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
> Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Date:   Fri Jul 10 07:19:37 2020 +0200
> 
>     ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
> 
>     The imx-pwm driver supports 3 cells and this is the more flexible setting.
>     So use it by default and overwrite it back to two for the files that
>     reference the PWMs with just 2 cells to minimize changes.
> 
>     This allows to drop explicit setting to 3 cells for the boards that already
>     depend on this. The boards that are now using 2 cells explicitly can be
>     converted to 3 individually.
> 
>     Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
>     Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OK, nice. Thx!

Should I resend this series without this patch?

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

On Thu, Jan 21, 2021 at 11:17:42AM -0300, Fabio Estevam wrote:
> Hi Oleksij,
> 
> On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> >
> > At some point PWM cell count was changed, but it didn't triggered any
> 
> It changed in this commit:
> 
> commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
> Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Date:   Fri Jul 10 07:19:37 2020 +0200
> 
>     ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
> 
>     The imx-pwm driver supports 3 cells and this is the more flexible setting.
>     So use it by default and overwrite it back to two for the files that
>     reference the PWMs with just 2 cells to minimize changes.
> 
>     This allows to drop explicit setting to 3 cells for the boards that already
>     depend on this. The boards that are now using 2 cells explicitly can be
>     converted to 3 individually.
> 
>     Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
>     Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OK, nice. Thx!

Should I resend this series without this patch?

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 6/7] ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.

[Oleksij Rempel]

On Thu, Jan 21, 2021 at 11:17:42AM -0300, Fabio Estevam wrote:
> Hi Oleksij,
> 
> On Thu, Jan 21, 2021 at 3:12 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> >
> > At some point PWM cell count was changed, but it didn't triggered any
> 
> It changed in this commit:
> 
> commit fa28d8212ede9c533ae87a737571a9d3b3eebb29
> Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Date:   Fri Jul 10 07:19:37 2020 +0200
> 
>     ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
> 
>     The imx-pwm driver supports 3 cells and this is the more flexible setting.
>     So use it by default and overwrite it back to two for the files that
>     reference the PWMs with just 2 cells to minimize changes.
> 
>     This allows to drop explicit setting to 3 cells for the boards that already
>     depend on this. The boards that are now using 2 cells explicitly can be
>     converted to 3 individually.
> 
>     Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
>     Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OK, nice. Thx!

Should I resend this series without this patch?

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0

[PATCH v2 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 7/7] ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties

[Oleksij Rempel]

Remove touchscreen-size-* properties.  This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
And the real range of values reported by the driver (or measured by the
controller) is close to max values and may change with time on resistive
panels. So, it make no sense to keep this values in the device tree.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-plym2m.dts | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 4d0d3d3386af..c97274f0df07 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel