From: <kostap@marvell.com> To: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org> Cc: <vladimir.vid@sartura.hr>, <tmn505@gmail.com>, <luka.kovacic@sartura.hr>, <sebastian.hesselbarth@gmail.com>, <gregory.clement@bootlin.com>, <andrew@lunn.ch>, <robh+dt@kernel.org>, <vkoul@kernel.org>, <kishon@ti.com>, <miquel.raynal@bootlin.com>, <mw@semihalf.com>, <jaz@semihalf.com>, <nadavh@marvell.com>, <stefanc@marvell.com>, <bpeled@marvell.com>, "Konstantin Porotchkin" <kostap@marvell.com> Subject: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms Date: Tue, 9 Feb 2021 15:46:05 +0200 [thread overview] Message-ID: <20210209134610.19904-1-kostap@marvell.com> (raw) From: Konstantin Porotchkin <kostap@marvell.com> This patch series contains the following changes/fixes: 1. Add support for Armada CN913x Development Board topology "B" 2. Add support for Armada CN913x Reference Design boards (CRB) 3. Fixes the CP11X references in PHY binding document 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions All above changes are already intergated into Marvell official SDK sources v2: - extract common nodes from DB boards to separate DTSI files - disable eth2 on CRB boards until the required phy mode support is added - mention the switch part ID in CRB board description v3: - do not rename setup A DTS files for DB variants - fix a couple of wrong include names v4: - Rebase on top of Linus master branch (v5.11-rc7) - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) - Add cd-gpio entry to CP0 SDHCI for SD card support - Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander - Add Stefan's patch to enable 10G port on CN9130-DB platforms Grzegorz Jaszczyk (1): Documentation/bindings: phy: update references to cp11x Konstantin Porotchkin (3): arch/arm64/boot/dts/marvell: fix NAND partitioning scheme arm64: dts: cn913x: add device trees for topology B boards arm64: dts: add support for Marvell cn9130-crb platform Stefan Chulski (1): dts: marvell: Enable 10G interface on 9130-DB board .../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: <kostap@marvell.com> To: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org> Cc: tmn505@gmail.com, andrew@lunn.ch, nadavh@marvell.com, jaz@semihalf.com, gregory.clement@bootlin.com, vkoul@kernel.org, kishon@ti.com, vladimir.vid@sartura.hr, luka.kovacic@sartura.hr, robh+dt@kernel.org, miquel.raynal@bootlin.com, Konstantin Porotchkin <kostap@marvell.com>, stefanc@marvell.com, mw@semihalf.com, bpeled@marvell.com, sebastian.hesselbarth@gmail.com Subject: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms Date: Tue, 9 Feb 2021 15:46:05 +0200 [thread overview] Message-ID: <20210209134610.19904-1-kostap@marvell.com> (raw) From: Konstantin Porotchkin <kostap@marvell.com> This patch series contains the following changes/fixes: 1. Add support for Armada CN913x Development Board topology "B" 2. Add support for Armada CN913x Reference Design boards (CRB) 3. Fixes the CP11X references in PHY binding document 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions All above changes are already intergated into Marvell official SDK sources v2: - extract common nodes from DB boards to separate DTSI files - disable eth2 on CRB boards until the required phy mode support is added - mention the switch part ID in CRB board description v3: - do not rename setup A DTS files for DB variants - fix a couple of wrong include names v4: - Rebase on top of Linus master branch (v5.11-rc7) - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) - Add cd-gpio entry to CP0 SDHCI for SD card support - Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander - Add Stefan's patch to enable 10G port on CN9130-DB platforms Grzegorz Jaszczyk (1): Documentation/bindings: phy: update references to cp11x Konstantin Porotchkin (3): arch/arm64/boot/dts/marvell: fix NAND partitioning scheme arm64: dts: cn913x: add device trees for topology B boards arm64: dts: add support for Marvell cn9130-crb platform Stefan Chulski (1): dts: marvell: Enable 10G interface on 9130-DB board .../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2021-02-09 13:50 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-02-09 13:46 kostap [this message] 2021-02-09 13:46 ` [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms kostap 2021-02-09 13:46 ` [PATCH v4 1/5] Documentation/bindings: phy: update references to cp11x kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 2/5] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 3/5] arm64: dts: cn913x: add device trees for topology B boards kostap 2021-02-09 13:46 ` kostap 2021-02-09 13:46 ` [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board kostap 2021-02-09 13:46 ` kostap 2021-02-09 14:13 ` Marcin Wojtas 2021-02-09 14:13 ` Marcin Wojtas 2021-02-09 13:46 ` [PATCH v4 5/5] arm64: dts: add support for Marvell cn9130-crb platform kostap 2021-02-09 13:46 ` kostap 2021-06-17 15:40 ` [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms Gregory CLEMENT 2021-06-17 15:40 ` Gregory CLEMENT 2021-07-08 7:50 ` [EXT] " Kostya Porotchkin 2021-07-08 7:50 ` Kostya Porotchkin
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210209134610.19904-1-kostap@marvell.com \ --to=kostap@marvell.com \ --cc=andrew@lunn.ch \ --cc=bpeled@marvell.com \ --cc=devicetree@vger.kernel.org \ --cc=gregory.clement@bootlin.com \ --cc=jaz@semihalf.com \ --cc=kishon@ti.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=luka.kovacic@sartura.hr \ --cc=miquel.raynal@bootlin.com \ --cc=mw@semihalf.com \ --cc=nadavh@marvell.com \ --cc=robh+dt@kernel.org \ --cc=sebastian.hesselbarth@gmail.com \ --cc=stefanc@marvell.com \ --cc=tmn505@gmail.com \ --cc=vkoul@kernel.org \ --cc=vladimir.vid@sartura.hr \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.