[PATCH v2 net-next 0/4] Add support for Qualcomm QCA807x PHYs

[PATCH v2 net-next 0/4] Add support for Qualcomm QCA807x PHYs

[Robert Marko]

This patch series adds support for Qualcomm QCA807x PHYs.

These are really common companion PHYs on boards featuring
Qualcomm IPQ40xx, IPQ60xx and IPQ807x SoCs.

They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.

They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.

Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.

Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.

Robert Marko (4):
  dt-bindings: net: Add QCA807x PHY
  dt-bindings: net: Add bindings for Qualcomm QCA807x
  net: phy: Add Qualcomm QCA807x driver
  MAINTAINERS: Add entry for Qualcomm QCA807x PHY driver

 .../devicetree/bindings/net/qcom,qca807x.yaml |  70 ++
 MAINTAINERS                                   |   9 +
 drivers/net/phy/Kconfig                       |  10 +
 drivers/net/phy/Makefile                      |   1 +
 drivers/net/phy/qca807x.c                     | 855 ++++++++++++++++++
 include/dt-bindings/net/qcom-qca807x.h        |  30 +
 6 files changed, 975 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom,qca807x.yaml
 create mode 100644 drivers/net/phy/qca807x.c
 create mode 100644 include/dt-bindings/net/qcom-qca807x.h

-- 
2.29.2

[PATCH v2 net-next 1/4] dt-bindings: net: Add QCA807x PHY

[Robert Marko]

Add DT bindings for Qualcomm QCA807x PHY series.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes in v2:
* Drop PSGMII/QSGMII TX driver defines

 include/dt-bindings/net/qcom-qca807x.h | 30 ++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
 create mode 100644 include/dt-bindings/net/qcom-qca807x.h

diff --git a/include/dt-bindings/net/qcom-qca807x.h b/include/dt-bindings/net/qcom-qca807x.h
new file mode 100644
index 000000000000..a5ac12777c2b
--- /dev/null
+++ b/include/dt-bindings/net/qcom-qca807x.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Device Tree constants for the Qualcomm QCA807X PHYs
+ */
+
+#ifndef _DT_BINDINGS_QCOM_QCA807X_H
+#define _DT_BINDINGS_QCOM_QCA807X_H
+
+/* Full amplitude, full bias current */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_BIAS		0
+/* Amplitude follow DSP (amplitude is adjusted based on cable length), half bias current */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS		1
+/* Full amplitude, bias current follow DSP (bias current is adjusted based on cable length) */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_DSP_BIAS		2
+/* Both amplitude and bias current follow DSP */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_BIAS		3
+/* Full amplitude, half bias current */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS		4
+/* Amplitude follow DSP setting; 1/4 bias current when cable<10m,
+ * otherwise half bias current
+ */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS	5
+/* Full amplitude; same bias current setting with “010” and “011”,
+ * but half more bias is reduced when cable <10m
+ */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS_SHORT	6
+/* Amplitude follow DSP; same bias current setting with “110”, default value */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS_SHORT	7
+
+#endif
-- 
2.29.2

Re: [PATCH v2 net-next 1/4] dt-bindings: net: Add QCA807x PHY

[Andrew Lunn]

On Wed, Feb 10, 2021 at 01:55:20PM +0100, Robert Marko wrote:
> Add DT bindings for Qualcomm QCA807x PHY series.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> ---
> Changes in v2:
> * Drop PSGMII/QSGMII TX driver defines
> 
>  include/dt-bindings/net/qcom-qca807x.h | 30 ++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
>  create mode 100644 include/dt-bindings/net/qcom-qca807x.h
> 
> diff --git a/include/dt-bindings/net/qcom-qca807x.h b/include/dt-bindings/net/qcom-qca807x.h
> new file mode 100644
> index 000000000000..a5ac12777c2b
> --- /dev/null
> +++ b/include/dt-bindings/net/qcom-qca807x.h
> @@ -0,0 +1,30 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Device Tree constants for the Qualcomm QCA807X PHYs
> + */
> +
> +#ifndef _DT_BINDINGS_QCOM_QCA807X_H
> +#define _DT_BINDINGS_QCOM_QCA807X_H
> +
> +/* Full amplitude, full bias current */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_BIAS		0
> +/* Amplitude follow DSP (amplitude is adjusted based on cable length), half bias current */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS		1
> +/* Full amplitude, bias current follow DSP (bias current is adjusted based on cable length) */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_DSP_BIAS		2
> +/* Both amplitude and bias current follow DSP */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_BIAS		3
> +/* Full amplitude, half bias current */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS		4
> +/* Amplitude follow DSP setting; 1/4 bias current when cable<10m,
> + * otherwise half bias current
> + */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS	5
> +/* Full amplitude; same bias current setting with “010” and “011”,
> + * but half more bias is reduced when cable <10m
> + */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS_SHORT	6
> +/* Amplitude follow DSP; same bias current setting with “110”, default value */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS_SHORT	7

Are these really properties of the board? That is what device tree is
supposed to be about. These seem like configuration options. Which
suggests they should actually be a PHY tunable.

	 Andrew

[PATCH v2 net-next 2/4] dt-bindings: net: Add bindings for Qualcomm QCA807x

[Robert Marko]

Add DT bindings for Qualcomm QCA807x PHYs.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes in v2:
* Drop LED properties
* Directly define PSGMII/QSGMII SerDes driver values

 .../devicetree/bindings/net/qcom,qca807x.yaml | 70 +++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom,qca807x.yaml

diff --git a/Documentation/devicetree/bindings/net/qcom,qca807x.yaml b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml
new file mode 100644
index 000000000000..0867f5e698cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qcom,qca807x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm QCA807x PHY
+
+maintainers:
+  - Robert Marko <robert.marko@sartura.hr>
+
+description: |
+  Bindings for Qualcomm QCA807x PHYs
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  reg:
+    maxItems: 1
+
+  qcom,fiber-enable:
+    description: |
+      If present, then PHYs combo port is configured to operate in combo
+      mode. In combo mode autodetection of copper and fiber media is
+      used in order to support both of them.
+      Combo mode can be strapped as well, if not strapped this property
+      will set combo support anyway.
+    type: boolean
+
+  qcom,psgmii-az:
+    description: |
+      If present, then PSMGII PHY will advertise 802.3-az support to
+      the MAC.
+    type: boolean
+
+  gpio-controller: true
+  "#gpio-cells":
+    const: 2
+
+  qcom,tx-driver-strength:
+    description: PSGMII/QSGMII SerDes TX driver strength control in mV.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [140, 160, 180, 200, 220, 240, 260, 280, 300, 320, 400, 500, 600]
+
+  qcom,control-dac:
+    description: Analog MDI driver amplitude and bias current.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+required:
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/net/qcom-qca807x.h>
+
+    mdio {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      ethphy0: ethernet-phy@0 {
+        compatible = "ethernet-phy-ieee802.3-c22";
+        reg = <0>;
+
+        qcom,control-dac = <QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS>;
+      };
+    };
-- 
2.29.2

Re: [PATCH v2 net-next 2/4] dt-bindings: net: Add bindings for Qualcomm QCA807x

[Rob Herring]

On Wed, Feb 10, 2021 at 01:55:21PM +0100, Robert Marko wrote:
> Add DT bindings for Qualcomm QCA807x PHYs.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> ---
> Changes in v2:
> * Drop LED properties
> * Directly define PSGMII/QSGMII SerDes driver values
> 
>  .../devicetree/bindings/net/qcom,qca807x.yaml | 70 +++++++++++++++++++
>  1 file changed, 70 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/qcom,qca807x.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/qcom,qca807x.yaml b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml
> new file mode 100644
> index 000000000000..0867f5e698cd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml
> @@ -0,0 +1,70 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/qcom,qca807x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm QCA807x PHY
> +
> +maintainers:
> +  - Robert Marko <robert.marko@sartura.hr>
> +
> +description: |
> +  Bindings for Qualcomm QCA807x PHYs
> +
> +allOf:
> +  - $ref: ethernet-phy.yaml#
> +
> +properties:
> +  reg:
> +    maxItems: 1
> +
> +  qcom,fiber-enable:
> +    description: |
> +      If present, then PHYs combo port is configured to operate in combo
> +      mode. In combo mode autodetection of copper and fiber media is
> +      used in order to support both of them.
> +      Combo mode can be strapped as well, if not strapped this property
> +      will set combo support anyway.
> +    type: boolean
> +
> +  qcom,psgmii-az:
> +    description: |
> +      If present, then PSMGII PHY will advertise 802.3-az support to
> +      the MAC.

Sounds like a standard thing that should be common?

> +    type: boolean
> +
> +  gpio-controller: true
> +  "#gpio-cells":
> +    const: 2
> +
> +  qcom,tx-driver-strength:
> +    description: PSGMII/QSGMII SerDes TX driver strength control in mV.

Use standard unit suffix as defined in property-units.txt.

Again, seems like a common property?

> +    $ref: /schemas/types.yaml#/definitions/uint32

Then you can drop this.

> +    enum: [140, 160, 180, 200, 220, 240, 260, 280, 300, 320, 400, 500, 600]
> +
> +  qcom,control-dac:
> +    description: Analog MDI driver amplitude and bias current.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2, 3, 4, 5, 6, 7]
> +
> +required:
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/net/qcom-qca807x.h>
> +
> +    mdio {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      ethphy0: ethernet-phy@0 {
> +        compatible = "ethernet-phy-ieee802.3-c22";
> +        reg = <0>;
> +
> +        qcom,control-dac = <QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS>;
> +      };
> +    };
> -- 
> 2.29.2
> 

[PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[Robert Marko]

This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.

They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.

They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.

Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.

Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.

This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.

This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.

These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes in v2:
* Drop LED related code
* Fix ordering in KConfig and Makefile
* Add SFP module validation upon instert
* Rework IRQ code
* Convert values for PSGMII/QSGMII SerDes driver
  into register values instead of using defines in dt-bindings
* Fill phydev->port with correct port type

 drivers/net/phy/Kconfig   |  10 +
 drivers/net/phy/Makefile  |   1 +
 drivers/net/phy/qca807x.c | 855 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 866 insertions(+)
 create mode 100644 drivers/net/phy/qca807x.c

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 92164e7b7f60..f0725d8acd4a 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -259,6 +259,16 @@ config AT803X_PHY
 	help
 	  Currently supports the AR8030, AR8031, AR8033 and AR8035 model
 
+config QCA807X_PHY
+	tristate "Qualcomm QCA807X PHYs"
+	depends on OF_MDIO
+	help
+	  Adds support for the Qualcomm QCA807x PHYs.
+	  These are 802.3 Clause 22 compliant PHYs supporting gigabit
+	  ethernet as well as 100Base-FX and 1000Base-X fibre.
+
+	  Currently supports the QCA8072 and QCA8075 models.
+
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index ca0a313423b9..25530057950e 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -73,6 +73,7 @@ obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
 obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
 obj-$(CONFIG_NATIONAL_PHY)	+= national.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
+obj-$(CONFIG_QCA807X_PHY)	+= qca807x.o
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
 obj-$(CONFIG_RENESAS_PHY)	+= uPD60620.o
diff --git a/drivers/net/phy/qca807x.c b/drivers/net/phy/qca807x.c
new file mode 100644
index 000000000000..9126035853e4
--- /dev/null
+++ b/drivers/net/phy/qca807x.c
@@ -0,0 +1,855 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020 Sartura Ltd.
+ *
+ * Author: Robert Marko <robert.marko@sartura.hr>
+ *
+ * Qualcomm QCA8072 and QCA8075 PHY driver
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/bitfield.h>
+#include <linux/ethtool_netlink.h>
+#include <linux/gpio.h>
+#include <linux/sfp.h>
+
+#include <dt-bindings/net/qcom-qca807x.h>
+
+#define PHY_ID_QCA8072		0x004dd0b2
+#define PHY_ID_QCA8075		0x004dd0b1
+#define PHY_ID_QCA807X_PSGMII	0x06820805
+
+/* Downshift */
+#define QCA807X_SMARTSPEED_EN			BIT(5)
+#define QCA807X_SMARTSPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
+#define QCA807X_SMARTSPEED_RETRY_LIMIT_DEFAULT	5
+#define QCA807X_SMARTSPEED_RETRY_LIMIT_MIN	2
+#define QCA807X_SMARTSPEED_RETRY_LIMIT_MAX	9
+
+/* Cable diagnostic test (CDT) */
+#define QCA807X_CDT						0x16
+#define QCA807X_CDT_ENABLE					BIT(15)
+#define QCA807X_CDT_ENABLE_INTER_PAIR_SHORT			BIT(13)
+#define QCA807X_CDT_STATUS					BIT(11)
+#define QCA807X_CDT_MMD3_STATUS					0x8064
+#define QCA807X_CDT_MDI0_STATUS_MASK				GENMASK(15, 12)
+#define QCA807X_CDT_MDI1_STATUS_MASK				GENMASK(11, 8)
+#define QCA807X_CDT_MDI2_STATUS_MASK				GENMASK(7, 4)
+#define QCA807X_CDT_MDI3_STATUS_MASK				GENMASK(3, 0)
+#define QCA807X_CDT_RESULTS_INVALID				0x0
+#define QCA807X_CDT_RESULTS_OK					0x1
+#define QCA807X_CDT_RESULTS_OPEN				0x2
+#define QCA807X_CDT_RESULTS_SAME_SHORT				0x3
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK	0x4
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK	0x8
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK	0xc
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN	0x6
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN	0xa
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN	0xe
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT	0x7
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT	0xb
+#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT	0xf
+#define QCA807X_CDT_RESULTS_BUSY				0x9
+#define QCA807X_CDT_MMD3_MDI0_LENGTH				0x8065
+#define QCA807X_CDT_MMD3_MDI1_LENGTH				0x8066
+#define QCA807X_CDT_MMD3_MDI2_LENGTH				0x8067
+#define QCA807X_CDT_MMD3_MDI3_LENGTH				0x8068
+#define QCA807X_CDT_SAME_SHORT_LENGTH_MASK			GENMASK(15, 8)
+#define QCA807X_CDT_CROSS_SHORT_LENGTH_MASK			GENMASK(7, 0)
+
+#define QCA807X_CHIP_CONFIGURATION				0x1f
+#define QCA807X_BT_BX_REG_SEL					BIT(15)
+#define QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK		GENMASK(3, 0)
+#define QCA807X_CHIP_CONFIGURATION_MODE_QSGMII_SGMII		4
+#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER		3
+#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_ALL_COPPER	0
+
+#define QCA807X_MEDIA_SELECT_STATUS				0x1a
+#define QCA807X_MEDIA_DETECTED_COPPER				BIT(5)
+#define QCA807X_MEDIA_DETECTED_1000_BASE_X			BIT(4)
+#define QCA807X_MEDIA_DETECTED_100_BASE_FX			BIT(3)
+
+#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION			0x807e
+#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN		BIT(0)
+
+#define QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH	0x801a
+#define QCA807X_CONTROL_DAC_MASK				GENMASK(2, 0)
+
+#define QCA807X_MMD7_LED_100N_1				0x8074
+#define QCA807X_MMD7_LED_100N_2				0x8075
+#define QCA807X_MMD7_LED_1000N_1			0x8076
+#define QCA807X_MMD7_LED_1000N_2			0x8077
+#define QCA807X_GPIO_FORCE_EN				BIT(15)
+#define QCA807X_GPIO_FORCE_MODE_MASK			GENMASK(14, 13)
+
+#define QCA807X_INTR_ENABLE				0x12
+#define QCA807X_INTR_STATUS				0x13
+#define QCA807X_INTR_ENABLE_AUTONEG_ERR			BIT(15)
+#define QCA807X_INTR_ENABLE_SPEED_CHANGED		BIT(14)
+#define QCA807X_INTR_ENABLE_DUPLEX_CHANGED		BIT(13)
+#define QCA807X_INTR_ENABLE_LINK_FAIL			BIT(11)
+#define QCA807X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
+
+#define QCA807X_FUNCTION_CONTROL			0x10
+#define QCA807X_FC_MDI_CROSSOVER_MODE_MASK		GENMASK(6, 5)
+#define QCA807X_FC_MDI_CROSSOVER_AUTO			3
+#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX		1
+#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI		0
+
+#define QCA807X_PHY_SPECIFIC_STATUS			0x11
+#define QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED		BIT(11)
+#define QCA807X_SS_SPEED_MASK				GENMASK(15, 14)
+#define QCA807X_SS_SPEED_1000				2
+#define QCA807X_SS_SPEED_100				1
+#define QCA807X_SS_SPEED_10				0
+#define QCA807X_SS_DUPLEX				BIT(13)
+#define QCA807X_SS_MDIX					BIT(6)
+
+/* PSGMII PHY specific */
+#define PSGMII_QSGMII_DRIVE_CONTROL_1			0xb
+#define PSGMII_QSGMII_TX_DRIVER_MASK			GENMASK(7, 4)
+#define PSGMII_MODE_CTRL				0x6d
+#define PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK		GENMASK(3, 0)
+#define PSGMII_MMD3_SERDES_CONTROL			0x805a
+
+struct qca807x_gpio_priv {
+	struct phy_device *phy;
+};
+
+static int qca807x_get_downshift(struct phy_device *phydev, u8 *data)
+{
+	int val, cnt, enable;
+
+	val = phy_read(phydev, MII_NWAYTEST);
+	if (val < 0)
+		return val;
+
+	enable = FIELD_GET(QCA807X_SMARTSPEED_EN, val);
+	cnt = FIELD_GET(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, val) + 2;
+
+	*data = enable ? cnt : DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int qca807x_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	int ret, val;
+
+	if (cnt > QCA807X_SMARTSPEED_RETRY_LIMIT_MAX ||
+	    (cnt < QCA807X_SMARTSPEED_RETRY_LIMIT_MIN && cnt != DOWNSHIFT_DEV_DISABLE))
+		return -EINVAL;
+
+	if (!cnt) {
+		ret = phy_clear_bits(phydev, MII_NWAYTEST, QCA807X_SMARTSPEED_EN);
+	} else {
+		val = QCA807X_SMARTSPEED_EN;
+		val |= FIELD_PREP(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, cnt - 2);
+
+		phy_modify(phydev, MII_NWAYTEST,
+			   QCA807X_SMARTSPEED_EN |
+			   QCA807X_SMARTSPEED_RETRY_LIMIT_MASK,
+			   val);
+	}
+
+	ret = genphy_soft_reset(phydev);
+
+	return ret;
+}
+
+static int qca807x_get_tunable(struct phy_device *phydev,
+			       struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return qca807x_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int qca807x_set_tunable(struct phy_device *phydev,
+			       struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return qca807x_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static bool qca807x_distance_valid(int result)
+{
+	switch (result) {
+	case QCA807X_CDT_RESULTS_OPEN:
+	case QCA807X_CDT_RESULTS_SAME_SHORT:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return true;
+	}
+	return false;
+}
+
+static int qca807x_report_length(struct phy_device *phydev,
+				 int pair, int result)
+{
+	int length;
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_MDI0_LENGTH + pair);
+	if (ret < 0)
+		return ret;
+
+	switch (result) {
+	case ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT:
+		length = (FIELD_GET(QCA807X_CDT_SAME_SHORT_LENGTH_MASK, ret) * 800) / 10;
+		break;
+	case ETHTOOL_A_CABLE_RESULT_CODE_OPEN:
+	case ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT:
+		length = (FIELD_GET(QCA807X_CDT_CROSS_SHORT_LENGTH_MASK, ret) * 800) / 10;
+		break;
+	}
+
+	ethnl_cable_test_fault_length(phydev, pair, length);
+
+	return 0;
+}
+
+static int qca807x_cable_test_report_trans(int result)
+{
+	switch (result) {
+	case QCA807X_CDT_RESULTS_OK:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+	case QCA807X_CDT_RESULTS_OPEN:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+	case QCA807X_CDT_RESULTS_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+	default:
+		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+}
+
+static int qca807x_cable_test_report(struct phy_device *phydev)
+{
+	int pair0, pair1, pair2, pair3;
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_STATUS);
+	if (ret < 0)
+		return ret;
+
+	pair0 = FIELD_GET(QCA807X_CDT_MDI0_STATUS_MASK, ret);
+	pair1 = FIELD_GET(QCA807X_CDT_MDI1_STATUS_MASK, ret);
+	pair2 = FIELD_GET(QCA807X_CDT_MDI2_STATUS_MASK, ret);
+	pair3 = FIELD_GET(QCA807X_CDT_MDI3_STATUS_MASK, ret);
+
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+				qca807x_cable_test_report_trans(pair0));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B,
+				qca807x_cable_test_report_trans(pair1));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C,
+				qca807x_cable_test_report_trans(pair2));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D,
+				qca807x_cable_test_report_trans(pair3));
+
+	if (qca807x_distance_valid(pair0))
+		qca807x_report_length(phydev, 0, qca807x_cable_test_report_trans(pair0));
+	if (qca807x_distance_valid(pair1))
+		qca807x_report_length(phydev, 1, qca807x_cable_test_report_trans(pair1));
+	if (qca807x_distance_valid(pair2))
+		qca807x_report_length(phydev, 2, qca807x_cable_test_report_trans(pair2));
+	if (qca807x_distance_valid(pair3))
+		qca807x_report_length(phydev, 3, qca807x_cable_test_report_trans(pair3));
+
+	return 0;
+}
+
+static int qca807x_cable_test_get_status(struct phy_device *phydev,
+					 bool *finished)
+{
+	int val;
+
+	*finished = false;
+
+	val = phy_read(phydev, QCA807X_CDT);
+	if (!((val & QCA807X_CDT_ENABLE) && (val & QCA807X_CDT_STATUS))) {
+		*finished = true;
+
+		return qca807x_cable_test_report(phydev);
+	}
+
+	return 0;
+}
+
+static int qca807x_cable_test_start(struct phy_device *phydev)
+{
+	int val, ret;
+
+	/* Check if fiber is being used in the combo port,
+	 * as we cant cable test fiber modules.
+	 */
+	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
+		if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+			val = phy_read(phydev, QCA807X_MEDIA_SELECT_STATUS);
+			if ((val & QCA807X_MEDIA_DETECTED_1000_BASE_X) ||
+			    (val & QCA807X_MEDIA_DETECTED_100_BASE_FX))
+				return -EOPNOTSUPP;
+		}
+	}
+
+	val = phy_read(phydev, QCA807X_CDT);
+	/* Enable inter-pair short check as well */
+	val &= ~QCA807X_CDT_ENABLE_INTER_PAIR_SHORT;
+	val |= QCA807X_CDT_ENABLE;
+	ret = phy_write(phydev, QCA807X_CDT, val);
+
+	return ret;
+}
+
+#ifdef CONFIG_GPIOLIB
+static int qca807x_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int qca807x_gpio_get_reg(unsigned int offset)
+{
+	return QCA807X_MMD7_LED_100N_2 + (offset % 2) * 2;
+}
+
+static int qca807x_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
+	int val;
+
+	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));
+
+	return FIELD_GET(QCA807X_GPIO_FORCE_MODE_MASK, val);
+}
+
+static void qca807x_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
+	int val;
+
+	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));
+	val &= ~QCA807X_GPIO_FORCE_MODE_MASK;
+	val |= FIELD_PREP(QCA807X_GPIO_FORCE_MODE_MASK, value);
+
+	phy_write_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset), val);
+}
+
+static int qca807x_gpio_dir_out(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	qca807x_gpio_set(gc, offset, value);
+
+	return 0;
+}
+
+static int qca807x_gpio(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct qca807x_gpio_priv *priv;
+	struct gpio_chip *gc;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->phy = phydev;
+
+	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	gc->label = dev_name(dev);
+	gc->base = -1;
+	gc->ngpio = 2;
+	gc->parent = dev;
+	gc->owner = THIS_MODULE;
+	gc->can_sleep = true;
+	gc->get_direction = qca807x_gpio_get_direction;
+	gc->direction_output = qca807x_gpio_dir_out;
+	gc->get = qca807x_gpio_get;
+	gc->set = qca807x_gpio_set;
+
+	return devm_gpiochip_add_data(dev, gc, priv);
+}
+#endif
+
+static int qca807x_read_copper_status(struct phy_device *phydev, bool combo_port)
+{
+	int ss, err, page, old_link = phydev->link;
+
+	if (phydev->port != PORT_TP)
+		phydev->port = PORT_TP;
+
+	/* Only combo port has dual pages */
+	if (combo_port) {
+		/* Check whether copper page is set and set if needed */
+		page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
+		if (!(page & QCA807X_BT_BX_REG_SEL)) {
+			page |= QCA807X_BT_BX_REG_SEL;
+			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
+		}
+	}
+
+	/* Update the link, but return if there was an error */
+	err = genphy_update_link(phydev);
+	if (err)
+		return err;
+
+	/* why bother the PHY if nothing can have changed */
+	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
+		return 0;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	err = genphy_read_lpa(phydev);
+	if (err < 0)
+		return err;
+
+	/* Read the QCA807x PHY-Specific Status register copper page,
+	 * which indicates the speed and duplex that the PHY is actually
+	 * using, irrespective of whether we are in autoneg mode or not.
+	 */
+	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
+	if (ss < 0)
+		return ss;
+
+	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
+		int sfc;
+
+		sfc = phy_read(phydev, QCA807X_FUNCTION_CONTROL);
+		if (sfc < 0)
+			return sfc;
+
+		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
+		case QCA807X_SS_SPEED_10:
+			phydev->speed = SPEED_10;
+			break;
+		case QCA807X_SS_SPEED_100:
+			phydev->speed = SPEED_100;
+			break;
+		case QCA807X_SS_SPEED_1000:
+			phydev->speed = SPEED_1000;
+			break;
+		}
+		if (ss & QCA807X_SS_DUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+
+		if (ss & QCA807X_SS_MDIX)
+			phydev->mdix = ETH_TP_MDI_X;
+		else
+			phydev->mdix = ETH_TP_MDI;
+
+		switch (FIELD_GET(QCA807X_FC_MDI_CROSSOVER_MODE_MASK, sfc)) {
+		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI:
+			phydev->mdix_ctrl = ETH_TP_MDI;
+			break;
+		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX:
+			phydev->mdix_ctrl = ETH_TP_MDI_X;
+			break;
+		case QCA807X_FC_MDI_CROSSOVER_AUTO:
+			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+			break;
+		}
+	}
+
+	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
+		phy_resolve_aneg_pause(phydev);
+
+	return 0;
+}
+
+static int qca807x_read_fiber_status(struct phy_device *phydev, bool combo_port)
+{
+	int ss, err, page;
+
+	if (phydev->port != PORT_FIBRE)
+		phydev->port = PORT_FIBRE;
+
+	/* Check whether fiber page is set and set if needed */
+	page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
+	if (page & QCA807X_BT_BX_REG_SEL) {
+		page &= ~QCA807X_BT_BX_REG_SEL;
+		phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
+	}
+
+	err = genphy_c37_read_status(phydev);
+	if (err)
+		return err;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+
+	/* Read the QCA807x PHY-Specific Status register fiber page,
+	 * which indicates the speed and duplex that the PHY is actually
+	 * using, irrespective of whether we are in autoneg mode or not.
+	 */
+	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
+	if (ss < 0)
+		return ss;
+
+	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
+		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
+		case QCA807X_SS_SPEED_100:
+			phydev->speed = SPEED_100;
+			break;
+		case QCA807X_SS_SPEED_1000:
+			phydev->speed = SPEED_1000;
+			break;
+		}
+
+		if (ss & QCA807X_SS_DUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+	}
+
+	return 0;
+}
+
+static int qca807x_read_status(struct phy_device *phydev)
+{
+	int val;
+
+	/* Check for Combo port */
+	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
+		/* Check for fiber mode first */
+		if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+			/* Check for actual detected media */
+			val = phy_read(phydev, QCA807X_MEDIA_SELECT_STATUS);
+			if (val & QCA807X_MEDIA_DETECTED_COPPER) {
+				qca807x_read_copper_status(phydev, true);
+			} else if ((val & QCA807X_MEDIA_DETECTED_1000_BASE_X) ||
+				   (val & QCA807X_MEDIA_DETECTED_100_BASE_FX)) {
+				qca807x_read_fiber_status(phydev, true);
+			}
+		} else {
+			qca807x_read_copper_status(phydev, true);
+		}
+	} else {
+		qca807x_read_copper_status(phydev, false);
+	}
+
+	return 0;
+}
+
+static int qca807x_ack_intr(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_read(phydev, QCA807X_INTR_STATUS);
+
+	return (ret < 0) ? ret : 0;
+}
+
+static int qca807x_config_intr(struct phy_device *phydev)
+{
+	int ret, val;
+
+	val = phy_read(phydev, QCA807X_INTR_ENABLE);
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+		/* Clear any pending interrupts */
+		ret = qca807x_ack_intr(phydev);
+		if (ret)
+			return ret;
+		/* Check for combo port as it has fewer interrupts */
+		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
+			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
+			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
+			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
+		} else {
+			val |= QCA807X_INTR_ENABLE_AUTONEG_ERR;
+			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
+			val |= QCA807X_INTR_ENABLE_DUPLEX_CHANGED;
+			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
+			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
+		}
+		ret = phy_write(phydev, QCA807X_INTR_ENABLE, val);
+	} else {
+		ret = phy_write(phydev, QCA807X_INTR_ENABLE, 0);
+		if (ret)
+			return ret;
+
+		/* Clear any pending interrupts */
+		ret = qca807x_ack_intr(phydev);
+	}
+
+	return ret;
+}
+
+static irqreturn_t qca807x_handle_interrupt(struct phy_device *phydev)
+{
+	int irq_status, int_enabled;
+
+	irq_status = phy_read(phydev, QCA807X_INTR_STATUS);
+	if (irq_status < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* Read the current enabled interrupts */
+	int_enabled = phy_read(phydev, QCA807X_INTR_ENABLE);
+	if (int_enabled < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* See if this was one of our enabled interrupts */
+	if (!(irq_status & int_enabled))
+		return IRQ_NONE;
+
+	phy_trigger_machine(phydev);
+
+	return IRQ_HANDLED;
+}
+
+static int qca807x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+	struct phy_device *phydev = upstream;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, };
+	phy_interface_t iface;
+
+	sfp_parse_support(phydev->sfp_bus, id, support);
+	iface = sfp_select_interface(phydev->sfp_bus, support);
+
+	if (iface != PHY_INTERFACE_MODE_1000BASEX &&
+	    iface != PHY_INTERFACE_MODE_SGMII) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct sfp_upstream_ops qca807x_sfp_ops = {
+	.attach = phy_sfp_attach,
+	.detach = phy_sfp_detach,
+	.module_insert = qca807x_sfp_insert,
+};
+
+static int qca807x_config(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	int control_dac, ret = 0;
+	u32 of_control_dac;
+
+	/* Check for Combo port */
+	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
+		int fiber_mode_autodect;
+		int psgmii_serdes;
+		int chip_config;
+
+		if (of_property_read_bool(node, "qcom,fiber-enable")) {
+			/* Enable fiber mode autodection (1000Base-X or 100Base-FX) */
+			fiber_mode_autodect = phy_read_mmd(phydev, MDIO_MMD_AN,
+							   QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION);
+			fiber_mode_autodect |= QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN;
+			phy_write_mmd(phydev, MDIO_MMD_AN, QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION,
+				      fiber_mode_autodect);
+
+			/* Enable 4 copper + combo port mode */
+			chip_config = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
+			chip_config &= ~QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK;
+			chip_config |= FIELD_PREP(QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK,
+						  QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER);
+			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, chip_config);
+
+			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
+			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->advertising);
+		}
+
+		/* Prevent PSGMII going into hibernation via PSGMII self test */
+		psgmii_serdes = phy_read_mmd(phydev, MDIO_MMD_PCS, PSGMII_MMD3_SERDES_CONTROL);
+		psgmii_serdes &= ~BIT(1);
+		ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
+				    PSGMII_MMD3_SERDES_CONTROL,
+				    psgmii_serdes);
+	}
+
+	if (!of_property_read_u32(node, "qcom,control-dac", &of_control_dac)) {
+		control_dac = phy_read_mmd(phydev, MDIO_MMD_AN,
+					   QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH);
+		control_dac &= ~QCA807X_CONTROL_DAC_MASK;
+		control_dac |= FIELD_PREP(QCA807X_CONTROL_DAC_MASK, of_control_dac);
+		ret = phy_write_mmd(phydev, MDIO_MMD_AN,
+				    QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH,
+				    control_dac);
+	}
+
+	return ret;
+}
+
+static int qca807x_probe(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	int ret = 0;
+
+	if (IS_ENABLED(CONFIG_GPIOLIB)) {
+		/* Do not register a GPIO controller unless flagged for it */
+		if (of_property_read_bool(node, "gpio-controller"))
+			ret = qca807x_gpio(phydev);
+	}
+
+	/* Attach SFP bus on combo port*/
+	if (of_property_read_bool(node, "qcom,fiber-enable")) {
+		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION))
+			ret = phy_sfp_probe(phydev, &qca807x_sfp_ops);
+	}
+
+	return ret;
+}
+
+static int qca807x_psgmii_config(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	int psgmii_az, tx_amp, ret = 0;
+	u32 tx_driver_strength_dt;
+
+	/* Workaround to enable AZ transmitting ability */
+	if (of_property_read_bool(node, "qcom,psgmii-az")) {
+		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
+		psgmii_az &= ~PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK;
+		psgmii_az |= FIELD_PREP(PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK, 0xc);
+		ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL, psgmii_az);
+		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
+	}
+
+	/* PSGMII/QSGMII TX amp set to DT defined value instead of default 600mV */
+	if (!of_property_read_u32(node, "qcom,tx-driver-strength", &tx_driver_strength_dt)) {
+		int tx_driver_strength;
+
+		switch (tx_driver_strength_dt) {
+		case 140:
+			tx_driver_strength = 0;
+			break;
+		case 160:
+			tx_driver_strength = 1;
+			break;
+		case 180:
+			tx_driver_strength = 2;
+			break;
+		case 200:
+			tx_driver_strength = 3;
+			break;
+		case 220:
+			tx_driver_strength = 4;
+			break;
+		case 240:
+			tx_driver_strength = 5;
+			break;
+		case 260:
+			tx_driver_strength = 6;
+			break;
+		case 280:
+			tx_driver_strength = 7;
+			break;
+		case 300:
+			tx_driver_strength = 8;
+			break;
+		case 320:
+			tx_driver_strength = 9;
+			break;
+		case 400:
+			tx_driver_strength = 10;
+			break;
+		case 500:
+			tx_driver_strength = 11;
+			break;
+		case 600:
+			tx_driver_strength = 12;
+			break;
+		default:
+			tx_driver_strength = 12;
+			break;
+		}
+
+		tx_amp = phy_read(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1);
+		tx_amp &= ~PSGMII_QSGMII_TX_DRIVER_MASK;
+		tx_amp |= FIELD_PREP(PSGMII_QSGMII_TX_DRIVER_MASK, tx_driver_strength);
+		ret = phy_write(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1, tx_amp);
+	}
+
+	return ret;
+}
+
+static struct phy_driver qca807x_drivers[] = {
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_QCA8072),
+		.name			= "Qualcomm QCA8072",
+		.flags			= PHY_POLL_CABLE_TEST,
+		/* PHY_GBIT_FEATURES */
+		.probe			= qca807x_probe,
+		.config_init		= qca807x_config,
+		.read_status		= qca807x_read_status,
+		.config_intr		= qca807x_config_intr,
+		.handle_interrupt	= qca807x_handle_interrupt,
+		.soft_reset		= genphy_soft_reset,
+		.get_tunable		= qca807x_get_tunable,
+		.set_tunable		= qca807x_set_tunable,
+		.cable_test_start	= qca807x_cable_test_start,
+		.cable_test_get_status	= qca807x_cable_test_get_status,
+	},
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_QCA8075),
+		.name			= "Qualcomm QCA8075",
+		.flags			= PHY_POLL_CABLE_TEST,
+		/* PHY_GBIT_FEATURES */
+		.probe			= qca807x_probe,
+		.config_init		= qca807x_config,
+		.read_status		= qca807x_read_status,
+		.config_intr		= qca807x_config_intr,
+		.handle_interrupt	= qca807x_handle_interrupt,
+		.soft_reset		= genphy_soft_reset,
+		.get_tunable		= qca807x_get_tunable,
+		.set_tunable		= qca807x_set_tunable,
+		.cable_test_start	= qca807x_cable_test_start,
+		.cable_test_get_status	= qca807x_cable_test_get_status,
+	},
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_QCA807X_PSGMII),
+		.name		= "Qualcomm QCA807x PSGMII",
+		.probe		= qca807x_psgmii_config,
+	},
+};
+module_phy_driver(qca807x_drivers);
+
+static struct mdio_device_id __maybe_unused qca807x_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8072) },
+	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8075) },
+	{ PHY_ID_MATCH_MODEL(PHY_ID_QCA807X_PSGMII) },
+	{ }
+};
+
+MODULE_AUTHOR("Robert Marko");
+MODULE_DESCRIPTION("Qualcomm QCA807x PHY driver");
+MODULE_DEVICE_TABLE(mdio, qca807x_tbl);
+MODULE_LICENSE("GPL");
-- 
2.29.2

Re: [PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[Heiner Kallweit]

On 10.02.2021 13:55, Robert Marko wrote:
> This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
> 
> They are 2 or 5 port IEEE 802.3 clause 22 compliant
> 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.
> 
> They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
> while second one is SGMII for connection to MAC or fiber.
> 
> Both models have a combo port that supports 1000BASE-X and 100BASE-FX
> fiber.
> 
> Each PHY inside of QCA807x series has 2 digitally controlled output only
> pins that natively drive LED-s.
> But some vendors used these to driver generic LED-s controlled by
> user space, so lets enable registering each PHY as GPIO controller and
> add driver for it.
> 
> This also adds the ability to specify DT properties so that 1000 Base-T
> LED will also be lit up for 100 and 10 Base connections.
> 
> This is usually done by U-boot, but boards running mainline U-boot are
> not configuring this yet.
> 
> These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
> boards.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> ---
> Changes in v2:
> * Drop LED related code
> * Fix ordering in KConfig and Makefile
> * Add SFP module validation upon instert
> * Rework IRQ code
> * Convert values for PSGMII/QSGMII SerDes driver
>   into register values instead of using defines in dt-bindings
> * Fill phydev->port with correct port type
> 
>  drivers/net/phy/Kconfig   |  10 +
>  drivers/net/phy/Makefile  |   1 +
>  drivers/net/phy/qca807x.c | 855 ++++++++++++++++++++++++++++++++++++++
>  3 files changed, 866 insertions(+)
>  create mode 100644 drivers/net/phy/qca807x.c
> 
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index 92164e7b7f60..f0725d8acd4a 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -259,6 +259,16 @@ config AT803X_PHY
>  	help
>  	  Currently supports the AR8030, AR8031, AR8033 and AR8035 model
>  
> +config QCA807X_PHY
> +	tristate "Qualcomm QCA807X PHYs"
> +	depends on OF_MDIO
> +	help
> +	  Adds support for the Qualcomm QCA807x PHYs.
> +	  These are 802.3 Clause 22 compliant PHYs supporting gigabit
> +	  ethernet as well as 100Base-FX and 1000Base-X fibre.
> +
> +	  Currently supports the QCA8072 and QCA8075 models.
> +
>  config QSEMI_PHY
>  	tristate "Quality Semiconductor PHYs"
>  	help
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index ca0a313423b9..25530057950e 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -73,6 +73,7 @@ obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
>  obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
>  obj-$(CONFIG_NATIONAL_PHY)	+= national.o
>  obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
> +obj-$(CONFIG_QCA807X_PHY)	+= qca807x.o
>  obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
>  obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
>  obj-$(CONFIG_RENESAS_PHY)	+= uPD60620.o
> diff --git a/drivers/net/phy/qca807x.c b/drivers/net/phy/qca807x.c
> new file mode 100644
> index 000000000000..9126035853e4
> --- /dev/null
> +++ b/drivers/net/phy/qca807x.c
> @@ -0,0 +1,855 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2020 Sartura Ltd.
> + *
> + * Author: Robert Marko <robert.marko@sartura.hr>
> + *
> + * Qualcomm QCA8072 and QCA8075 PHY driver
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy.h>
> +#include <linux/bitfield.h>
> +#include <linux/ethtool_netlink.h>
> +#include <linux/gpio.h>
> +#include <linux/sfp.h>
> +
> +#include <dt-bindings/net/qcom-qca807x.h>
> +
> +#define PHY_ID_QCA8072		0x004dd0b2
> +#define PHY_ID_QCA8075		0x004dd0b1
> +#define PHY_ID_QCA807X_PSGMII	0x06820805
> +
> +/* Downshift */
> +#define QCA807X_SMARTSPEED_EN			BIT(5)
> +#define QCA807X_SMARTSPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
> +#define QCA807X_SMARTSPEED_RETRY_LIMIT_DEFAULT	5
> +#define QCA807X_SMARTSPEED_RETRY_LIMIT_MIN	2
> +#define QCA807X_SMARTSPEED_RETRY_LIMIT_MAX	9
> +
> +/* Cable diagnostic test (CDT) */
> +#define QCA807X_CDT						0x16
> +#define QCA807X_CDT_ENABLE					BIT(15)
> +#define QCA807X_CDT_ENABLE_INTER_PAIR_SHORT			BIT(13)
> +#define QCA807X_CDT_STATUS					BIT(11)
> +#define QCA807X_CDT_MMD3_STATUS					0x8064
> +#define QCA807X_CDT_MDI0_STATUS_MASK				GENMASK(15, 12)
> +#define QCA807X_CDT_MDI1_STATUS_MASK				GENMASK(11, 8)
> +#define QCA807X_CDT_MDI2_STATUS_MASK				GENMASK(7, 4)
> +#define QCA807X_CDT_MDI3_STATUS_MASK				GENMASK(3, 0)
> +#define QCA807X_CDT_RESULTS_INVALID				0x0
> +#define QCA807X_CDT_RESULTS_OK					0x1
> +#define QCA807X_CDT_RESULTS_OPEN				0x2
> +#define QCA807X_CDT_RESULTS_SAME_SHORT				0x3
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK	0x4
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK	0x8
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK	0xc
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN	0x6
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN	0xa
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN	0xe
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT	0x7
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT	0xb
> +#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT	0xf
> +#define QCA807X_CDT_RESULTS_BUSY				0x9
> +#define QCA807X_CDT_MMD3_MDI0_LENGTH				0x8065
> +#define QCA807X_CDT_MMD3_MDI1_LENGTH				0x8066
> +#define QCA807X_CDT_MMD3_MDI2_LENGTH				0x8067
> +#define QCA807X_CDT_MMD3_MDI3_LENGTH				0x8068
> +#define QCA807X_CDT_SAME_SHORT_LENGTH_MASK			GENMASK(15, 8)
> +#define QCA807X_CDT_CROSS_SHORT_LENGTH_MASK			GENMASK(7, 0)
> +
> +#define QCA807X_CHIP_CONFIGURATION				0x1f
> +#define QCA807X_BT_BX_REG_SEL					BIT(15)
> +#define QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK		GENMASK(3, 0)
> +#define QCA807X_CHIP_CONFIGURATION_MODE_QSGMII_SGMII		4
> +#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER		3
> +#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_ALL_COPPER	0
> +
> +#define QCA807X_MEDIA_SELECT_STATUS				0x1a
> +#define QCA807X_MEDIA_DETECTED_COPPER				BIT(5)
> +#define QCA807X_MEDIA_DETECTED_1000_BASE_X			BIT(4)
> +#define QCA807X_MEDIA_DETECTED_100_BASE_FX			BIT(3)
> +
> +#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION			0x807e
> +#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN		BIT(0)
> +
> +#define QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH	0x801a
> +#define QCA807X_CONTROL_DAC_MASK				GENMASK(2, 0)
> +
> +#define QCA807X_MMD7_LED_100N_1				0x8074
> +#define QCA807X_MMD7_LED_100N_2				0x8075
> +#define QCA807X_MMD7_LED_1000N_1			0x8076
> +#define QCA807X_MMD7_LED_1000N_2			0x8077
> +#define QCA807X_GPIO_FORCE_EN				BIT(15)
> +#define QCA807X_GPIO_FORCE_MODE_MASK			GENMASK(14, 13)
> +
> +#define QCA807X_INTR_ENABLE				0x12
> +#define QCA807X_INTR_STATUS				0x13
> +#define QCA807X_INTR_ENABLE_AUTONEG_ERR			BIT(15)
> +#define QCA807X_INTR_ENABLE_SPEED_CHANGED		BIT(14)
> +#define QCA807X_INTR_ENABLE_DUPLEX_CHANGED		BIT(13)
> +#define QCA807X_INTR_ENABLE_LINK_FAIL			BIT(11)
> +#define QCA807X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
> +
> +#define QCA807X_FUNCTION_CONTROL			0x10
> +#define QCA807X_FC_MDI_CROSSOVER_MODE_MASK		GENMASK(6, 5)
> +#define QCA807X_FC_MDI_CROSSOVER_AUTO			3
> +#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX		1
> +#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI		0
> +
> +#define QCA807X_PHY_SPECIFIC_STATUS			0x11
> +#define QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED		BIT(11)
> +#define QCA807X_SS_SPEED_MASK				GENMASK(15, 14)
> +#define QCA807X_SS_SPEED_1000				2
> +#define QCA807X_SS_SPEED_100				1
> +#define QCA807X_SS_SPEED_10				0
> +#define QCA807X_SS_DUPLEX				BIT(13)
> +#define QCA807X_SS_MDIX					BIT(6)
> +
> +/* PSGMII PHY specific */
> +#define PSGMII_QSGMII_DRIVE_CONTROL_1			0xb
> +#define PSGMII_QSGMII_TX_DRIVER_MASK			GENMASK(7, 4)
> +#define PSGMII_MODE_CTRL				0x6d
> +#define PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK		GENMASK(3, 0)
> +#define PSGMII_MMD3_SERDES_CONTROL			0x805a
> +
> +struct qca807x_gpio_priv {
> +	struct phy_device *phy;
> +};
> +
> +static int qca807x_get_downshift(struct phy_device *phydev, u8 *data)
> +{
> +	int val, cnt, enable;
> +
> +	val = phy_read(phydev, MII_NWAYTEST);
> +	if (val < 0)
> +		return val;
> +
> +	enable = FIELD_GET(QCA807X_SMARTSPEED_EN, val);
> +	cnt = FIELD_GET(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, val) + 2;
> +
> +	*data = enable ? cnt : DOWNSHIFT_DEV_DISABLE;
> +
> +	return 0;
> +}
> +
> +static int qca807x_set_downshift(struct phy_device *phydev, u8 cnt)
> +{
> +	int ret, val;
> +
> +	if (cnt > QCA807X_SMARTSPEED_RETRY_LIMIT_MAX ||
> +	    (cnt < QCA807X_SMARTSPEED_RETRY_LIMIT_MIN && cnt != DOWNSHIFT_DEV_DISABLE))
> +		return -EINVAL;
> +
> +	if (!cnt) {
> +		ret = phy_clear_bits(phydev, MII_NWAYTEST, QCA807X_SMARTSPEED_EN);
> +	} else {
> +		val = QCA807X_SMARTSPEED_EN;
> +		val |= FIELD_PREP(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, cnt - 2);
> +
> +		phy_modify(phydev, MII_NWAYTEST,
> +			   QCA807X_SMARTSPEED_EN |
> +			   QCA807X_SMARTSPEED_RETRY_LIMIT_MASK,
> +			   val);
> +	}
> +
> +	ret = genphy_soft_reset(phydev);
> +
> +	return ret;
> +}
> +
> +static int qca807x_get_tunable(struct phy_device *phydev,
> +			       struct ethtool_tunable *tuna, void *data)
> +{
> +	switch (tuna->id) {
> +	case ETHTOOL_PHY_DOWNSHIFT:
> +		return qca807x_get_downshift(phydev, data);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static int qca807x_set_tunable(struct phy_device *phydev,
> +			       struct ethtool_tunable *tuna, const void *data)
> +{
> +	switch (tuna->id) {
> +	case ETHTOOL_PHY_DOWNSHIFT:
> +		return qca807x_set_downshift(phydev, *(const u8 *)data);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static bool qca807x_distance_valid(int result)
> +{
> +	switch (result) {
> +	case QCA807X_CDT_RESULTS_OPEN:
> +	case QCA807X_CDT_RESULTS_SAME_SHORT:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
> +		return true;
> +	}
> +	return false;
> +}
> +
> +static int qca807x_report_length(struct phy_device *phydev,
> +				 int pair, int result)
> +{
> +	int length;
> +	int ret;
> +
> +	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_MDI0_LENGTH + pair);
> +	if (ret < 0)
> +		return ret;
> +
> +	switch (result) {
> +	case ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT:
> +		length = (FIELD_GET(QCA807X_CDT_SAME_SHORT_LENGTH_MASK, ret) * 800) / 10;
> +		break;
> +	case ETHTOOL_A_CABLE_RESULT_CODE_OPEN:
> +	case ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT:
> +		length = (FIELD_GET(QCA807X_CDT_CROSS_SHORT_LENGTH_MASK, ret) * 800) / 10;
> +		break;
> +	}
> +
> +	ethnl_cable_test_fault_length(phydev, pair, length);
> +
> +	return 0;
> +}
> +
> +static int qca807x_cable_test_report_trans(int result)
> +{
> +	switch (result) {
> +	case QCA807X_CDT_RESULTS_OK:
> +		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
> +	case QCA807X_CDT_RESULTS_OPEN:
> +		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
> +	case QCA807X_CDT_RESULTS_SAME_SHORT:
> +		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
> +	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
> +		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
> +	default:
> +		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
> +	}
> +}
> +
> +static int qca807x_cable_test_report(struct phy_device *phydev)
> +{
> +	int pair0, pair1, pair2, pair3;
> +	int ret;
> +
> +	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_STATUS);
> +	if (ret < 0)
> +		return ret;
> +
> +	pair0 = FIELD_GET(QCA807X_CDT_MDI0_STATUS_MASK, ret);
> +	pair1 = FIELD_GET(QCA807X_CDT_MDI1_STATUS_MASK, ret);
> +	pair2 = FIELD_GET(QCA807X_CDT_MDI2_STATUS_MASK, ret);
> +	pair3 = FIELD_GET(QCA807X_CDT_MDI3_STATUS_MASK, ret);
> +
> +	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
> +				qca807x_cable_test_report_trans(pair0));
> +	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B,
> +				qca807x_cable_test_report_trans(pair1));
> +	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C,
> +				qca807x_cable_test_report_trans(pair2));
> +	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D,
> +				qca807x_cable_test_report_trans(pair3));
> +
> +	if (qca807x_distance_valid(pair0))
> +		qca807x_report_length(phydev, 0, qca807x_cable_test_report_trans(pair0));
> +	if (qca807x_distance_valid(pair1))
> +		qca807x_report_length(phydev, 1, qca807x_cable_test_report_trans(pair1));
> +	if (qca807x_distance_valid(pair2))
> +		qca807x_report_length(phydev, 2, qca807x_cable_test_report_trans(pair2));
> +	if (qca807x_distance_valid(pair3))
> +		qca807x_report_length(phydev, 3, qca807x_cable_test_report_trans(pair3));
> +
> +	return 0;
> +}
> +
> +static int qca807x_cable_test_get_status(struct phy_device *phydev,
> +					 bool *finished)
> +{
> +	int val;
> +
> +	*finished = false;
> +
> +	val = phy_read(phydev, QCA807X_CDT);
> +	if (!((val & QCA807X_CDT_ENABLE) && (val & QCA807X_CDT_STATUS))) {
> +		*finished = true;
> +
> +		return qca807x_cable_test_report(phydev);
> +	}
> +
> +	return 0;
> +}
> +
> +static int qca807x_cable_test_start(struct phy_device *phydev)
> +{
> +	int val, ret;
> +
> +	/* Check if fiber is being used in the combo port,
> +	 * as we cant cable test fiber modules.
> +	 */
> +	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
> +		if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
> +			val = phy_read(phydev, QCA807X_MEDIA_SELECT_STATUS);
> +			if ((val & QCA807X_MEDIA_DETECTED_1000_BASE_X) ||
> +			    (val & QCA807X_MEDIA_DETECTED_100_BASE_FX))
> +				return -EOPNOTSUPP;
> +		}
> +	}
> +
> +	val = phy_read(phydev, QCA807X_CDT);
> +	/* Enable inter-pair short check as well */
> +	val &= ~QCA807X_CDT_ENABLE_INTER_PAIR_SHORT;
> +	val |= QCA807X_CDT_ENABLE;
> +	ret = phy_write(phydev, QCA807X_CDT, val);
> +
> +	return ret;
> +}
> +
> +#ifdef CONFIG_GPIOLIB
> +static int qca807x_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
> +{
> +	return GPIO_LINE_DIRECTION_OUT;
> +}
> +
> +static int qca807x_gpio_get_reg(unsigned int offset)
> +{
> +	return QCA807X_MMD7_LED_100N_2 + (offset % 2) * 2;
> +}
> +
> +static int qca807x_gpio_get(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
> +	int val;
> +
> +	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));
> +
> +	return FIELD_GET(QCA807X_GPIO_FORCE_MODE_MASK, val);
> +}
> +
> +static void qca807x_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> +	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
> +	int val;
> +
> +	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));
> +	val &= ~QCA807X_GPIO_FORCE_MODE_MASK;
> +	val |= FIELD_PREP(QCA807X_GPIO_FORCE_MODE_MASK, value);
> +
> +	phy_write_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset), val);

You could use phy_modify_mmd() here.

> +}
> +
> +static int qca807x_gpio_dir_out(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> +	qca807x_gpio_set(gc, offset, value);
> +
> +	return 0;
> +}
> +
> +static int qca807x_gpio(struct phy_device *phydev)
> +{
> +	struct device *dev = &phydev->mdio.dev;
> +	struct qca807x_gpio_priv *priv;
> +	struct gpio_chip *gc;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->phy = phydev;
> +
> +	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
> +	if (!gc)
> +		return -ENOMEM;
> +
> +	gc->label = dev_name(dev);
> +	gc->base = -1;
> +	gc->ngpio = 2;
> +	gc->parent = dev;
> +	gc->owner = THIS_MODULE;
> +	gc->can_sleep = true;
> +	gc->get_direction = qca807x_gpio_get_direction;
> +	gc->direction_output = qca807x_gpio_dir_out;
> +	gc->get = qca807x_gpio_get;
> +	gc->set = qca807x_gpio_set;
> +
> +	return devm_gpiochip_add_data(dev, gc, priv);
> +}
> +#endif
> +
> +static int qca807x_read_copper_status(struct phy_device *phydev, bool combo_port)
> +{
> +	int ss, err, page, old_link = phydev->link;
> +
> +	if (phydev->port != PORT_TP)
> +		phydev->port = PORT_TP;
> +
> +	/* Only combo port has dual pages */
> +	if (combo_port) {
> +		/* Check whether copper page is set and set if needed */
> +		page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
> +		if (!(page & QCA807X_BT_BX_REG_SEL)) {
> +			page |= QCA807X_BT_BX_REG_SEL;
> +			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
> +		}
> +	}
> +
> +	/* Update the link, but return if there was an error */
> +	err = genphy_update_link(phydev);
> +	if (err)
> +		return err;
> +
> +	/* why bother the PHY if nothing can have changed */
> +	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
> +		return 0;
> +
> +	phydev->speed = SPEED_UNKNOWN;
> +	phydev->duplex = DUPLEX_UNKNOWN;
> +	phydev->pause = 0;
> +	phydev->asym_pause = 0;
> +
> +	err = genphy_read_lpa(phydev);
> +	if (err < 0)
> +		return err;
> +
> +	/* Read the QCA807x PHY-Specific Status register copper page,
> +	 * which indicates the speed and duplex that the PHY is actually
> +	 * using, irrespective of whether we are in autoneg mode or not.
> +	 */
> +	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
> +	if (ss < 0)
> +		return ss;
> +
> +	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
> +		int sfc;
> +
> +		sfc = phy_read(phydev, QCA807X_FUNCTION_CONTROL);
> +		if (sfc < 0)
> +			return sfc;
> +
> +		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
> +		case QCA807X_SS_SPEED_10:
> +			phydev->speed = SPEED_10;
> +			break;
> +		case QCA807X_SS_SPEED_100:
> +			phydev->speed = SPEED_100;
> +			break;
> +		case QCA807X_SS_SPEED_1000:
> +			phydev->speed = SPEED_1000;
> +			break;
> +		}
> +		if (ss & QCA807X_SS_DUPLEX)
> +			phydev->duplex = DUPLEX_FULL;
> +		else
> +			phydev->duplex = DUPLEX_HALF;
> +
> +		if (ss & QCA807X_SS_MDIX)
> +			phydev->mdix = ETH_TP_MDI_X;
> +		else
> +			phydev->mdix = ETH_TP_MDI;
> +
> +		switch (FIELD_GET(QCA807X_FC_MDI_CROSSOVER_MODE_MASK, sfc)) {
> +		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI:
> +			phydev->mdix_ctrl = ETH_TP_MDI;
> +			break;
> +		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX:
> +			phydev->mdix_ctrl = ETH_TP_MDI_X;
> +			break;
> +		case QCA807X_FC_MDI_CROSSOVER_AUTO:
> +			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
> +			break;
> +		}
> +	}
> +
> +	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
> +		phy_resolve_aneg_pause(phydev);
> +
> +	return 0;
> +}
> +
> +static int qca807x_read_fiber_status(struct phy_device *phydev, bool combo_port)
> +{
> +	int ss, err, page;
> +
> +	if (phydev->port != PORT_FIBRE)
> +		phydev->port = PORT_FIBRE;
> +
> +	/* Check whether fiber page is set and set if needed */
> +	page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
> +	if (page & QCA807X_BT_BX_REG_SEL) {
> +		page &= ~QCA807X_BT_BX_REG_SEL;
> +		phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
> +	}
> +
> +	err = genphy_c37_read_status(phydev);
> +	if (err)
> +		return err;
> +
> +	phydev->speed = SPEED_UNKNOWN;
> +	phydev->duplex = DUPLEX_UNKNOWN;
> +
> +	/* Read the QCA807x PHY-Specific Status register fiber page,
> +	 * which indicates the speed and duplex that the PHY is actually
> +	 * using, irrespective of whether we are in autoneg mode or not.
> +	 */
> +	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
> +	if (ss < 0)
> +		return ss;
> +
> +	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
> +		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
> +		case QCA807X_SS_SPEED_100:
> +			phydev->speed = SPEED_100;
> +			break;
> +		case QCA807X_SS_SPEED_1000:
> +			phydev->speed = SPEED_1000;
> +			break;
> +		}
> +
> +		if (ss & QCA807X_SS_DUPLEX)
> +			phydev->duplex = DUPLEX_FULL;
> +		else
> +			phydev->duplex = DUPLEX_HALF;
> +	}
> +
> +	return 0;
> +}
> +
> +static int qca807x_read_status(struct phy_device *phydev)
> +{
> +	int val;
> +
> +	/* Check for Combo port */
> +	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
> +		/* Check for fiber mode first */
> +		if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
> +			/* Check for actual detected media */
> +			val = phy_read(phydev, QCA807X_MEDIA_SELECT_STATUS);
> +			if (val & QCA807X_MEDIA_DETECTED_COPPER) {
> +				qca807x_read_copper_status(phydev, true);
> +			} else if ((val & QCA807X_MEDIA_DETECTED_1000_BASE_X) ||
> +				   (val & QCA807X_MEDIA_DETECTED_100_BASE_FX)) {
> +				qca807x_read_fiber_status(phydev, true);
> +			}
> +		} else {
> +			qca807x_read_copper_status(phydev, true);
> +		}
> +	} else {
> +		qca807x_read_copper_status(phydev, false);
> +	}
> +
> +	return 0;
> +}
> +
> +static int qca807x_ack_intr(struct phy_device *phydev)
> +{
> +	int ret;
> +
> +	ret = phy_read(phydev, QCA807X_INTR_STATUS);
> +
> +	return (ret < 0) ? ret : 0;
> +}
> +
> +static int qca807x_config_intr(struct phy_device *phydev)
> +{
> +	int ret, val;
> +
> +	val = phy_read(phydev, QCA807X_INTR_ENABLE);
> +
No check for val < 0 here?

> +	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
> +		/* Clear any pending interrupts */
> +		ret = qca807x_ack_intr(phydev);
> +		if (ret)
> +			return ret;
> +		/* Check for combo port as it has fewer interrupts */
> +		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
> +			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
> +			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
> +			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
> +		} else {
> +			val |= QCA807X_INTR_ENABLE_AUTONEG_ERR;
> +			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
> +			val |= QCA807X_INTR_ENABLE_DUPLEX_CHANGED;
> +			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
> +			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
> +		}

Your interrupt handler has no extra functionality, therefore it
should be sufficient to get the link change events only.

> +		ret = phy_write(phydev, QCA807X_INTR_ENABLE, val);
> +	} else {
> +		ret = phy_write(phydev, QCA807X_INTR_ENABLE, 0);
> +		if (ret)
> +			return ret;
> +
> +		/* Clear any pending interrupts */
> +		ret = qca807x_ack_intr(phydev);
> +	}
> +
> +	return ret;
> +}
> +
> +static irqreturn_t qca807x_handle_interrupt(struct phy_device *phydev)
> +{
> +	int irq_status, int_enabled;
> +
> +	irq_status = phy_read(phydev, QCA807X_INTR_STATUS);
> +	if (irq_status < 0) {
> +		phy_error(phydev);
> +		return IRQ_NONE;
> +	}
> +
> +	/* Read the current enabled interrupts */
> +	int_enabled = phy_read(phydev, QCA807X_INTR_ENABLE);
> +	if (int_enabled < 0) {
> +		phy_error(phydev);
> +		return IRQ_NONE;
> +	}
> +
> +	/* See if this was one of our enabled interrupts */
> +	if (!(irq_status & int_enabled))
> +		return IRQ_NONE;
> +
> +	phy_trigger_machine(phydev);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int qca807x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
> +{
> +	struct phy_device *phydev = upstream;
> +	__ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, };
> +	phy_interface_t iface;
> +
> +	sfp_parse_support(phydev->sfp_bus, id, support);
> +	iface = sfp_select_interface(phydev->sfp_bus, support);
> +
> +	if (iface != PHY_INTERFACE_MODE_1000BASEX &&
> +	    iface != PHY_INTERFACE_MODE_SGMII) {
> +		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct sfp_upstream_ops qca807x_sfp_ops = {
> +	.attach = phy_sfp_attach,
> +	.detach = phy_sfp_detach,
> +	.module_insert = qca807x_sfp_insert,
> +};
> +
> +static int qca807x_config(struct phy_device *phydev)
> +{
> +	struct device_node *node = phydev->mdio.dev.of_node;
> +	int control_dac, ret = 0;
> +	u32 of_control_dac;
> +
> +	/* Check for Combo port */
> +	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
> +		int fiber_mode_autodect;
> +		int psgmii_serdes;
> +		int chip_config;
> +
> +		if (of_property_read_bool(node, "qcom,fiber-enable")) {
> +			/* Enable fiber mode autodection (1000Base-X or 100Base-FX) */
> +			fiber_mode_autodect = phy_read_mmd(phydev, MDIO_MMD_AN,
> +							   QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION);
> +			fiber_mode_autodect |= QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN;
> +			phy_write_mmd(phydev, MDIO_MMD_AN, QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION,
> +				      fiber_mode_autodect);
> +
> +			/* Enable 4 copper + combo port mode */
> +			chip_config = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
> +			chip_config &= ~QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK;
> +			chip_config |= FIELD_PREP(QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK,
> +						  QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER);
> +			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, chip_config);
> +
> +			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
> +			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->advertising);
> +		}
> +
> +		/* Prevent PSGMII going into hibernation via PSGMII self test */
> +		psgmii_serdes = phy_read_mmd(phydev, MDIO_MMD_PCS, PSGMII_MMD3_SERDES_CONTROL);
> +		psgmii_serdes &= ~BIT(1);
> +		ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
> +				    PSGMII_MMD3_SERDES_CONTROL,
> +				    psgmii_serdes);

Here phy_modify_mmd() could be used too, same a few lines later.

> +	}
> +
> +	if (!of_property_read_u32(node, "qcom,control-dac", &of_control_dac)) {
> +		control_dac = phy_read_mmd(phydev, MDIO_MMD_AN,
> +					   QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH);
> +		control_dac &= ~QCA807X_CONTROL_DAC_MASK;
> +		control_dac |= FIELD_PREP(QCA807X_CONTROL_DAC_MASK, of_control_dac);
> +		ret = phy_write_mmd(phydev, MDIO_MMD_AN,
> +				    QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH,
> +				    control_dac);
> +	}
> +
> +	return ret;
> +}
> +
> +static int qca807x_probe(struct phy_device *phydev)
> +{
> +	struct device_node *node = phydev->mdio.dev.of_node;
> +	int ret = 0;
> +
> +	if (IS_ENABLED(CONFIG_GPIOLIB)) {
> +		/* Do not register a GPIO controller unless flagged for it */
> +		if (of_property_read_bool(node, "gpio-controller"))
> +			ret = qca807x_gpio(phydev);

The return value is ignored if fiber is enabled. I think the function
can return -EPROBE_DEFER, and that would be something you want to
propagate to the caller.

> +	}
> +
> +	/* Attach SFP bus on combo port*/
> +	if (of_property_read_bool(node, "qcom,fiber-enable")) {
> +		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION))
> +			ret = phy_sfp_probe(phydev, &qca807x_sfp_ops);
> +	}
> +
> +	return ret;
> +}
> +
> +static int qca807x_psgmii_config(struct phy_device *phydev)
> +{
> +	struct device_node *node = phydev->mdio.dev.of_node;
> +	int psgmii_az, tx_amp, ret = 0;
> +	u32 tx_driver_strength_dt;
> +
> +	/* Workaround to enable AZ transmitting ability */
> +	if (of_property_read_bool(node, "qcom,psgmii-az")) {
> +		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
> +		psgmii_az &= ~PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK;
> +		psgmii_az |= FIELD_PREP(PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK, 0xc);
> +		ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL, psgmii_az);
> +		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
> +	}
> +
> +	/* PSGMII/QSGMII TX amp set to DT defined value instead of default 600mV */
> +	if (!of_property_read_u32(node, "qcom,tx-driver-strength", &tx_driver_strength_dt)) {
> +		int tx_driver_strength;
> +
> +		switch (tx_driver_strength_dt) {
> +		case 140:
> +			tx_driver_strength = 0;
> +			break;
> +		case 160:
> +			tx_driver_strength = 1;
> +			break;
> +		case 180:
> +			tx_driver_strength = 2;
> +			break;
> +		case 200:
> +			tx_driver_strength = 3;
> +			break;
> +		case 220:
> +			tx_driver_strength = 4;
> +			break;
> +		case 240:
> +			tx_driver_strength = 5;
> +			break;
> +		case 260:
> +			tx_driver_strength = 6;
> +			break;
> +		case 280:
> +			tx_driver_strength = 7;
> +			break;
> +		case 300:
> +			tx_driver_strength = 8;
> +			break;
> +		case 320:
> +			tx_driver_strength = 9;
> +			break;
> +		case 400:
> +			tx_driver_strength = 10;
> +			break;
> +		case 500:
> +			tx_driver_strength = 11;
> +			break;
> +		case 600:
> +			tx_driver_strength = 12;
> +			break;
> +		default:
> +			tx_driver_strength = 12;
> +			break;
> +		}
> +
> +		tx_amp = phy_read(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1);
> +		tx_amp &= ~PSGMII_QSGMII_TX_DRIVER_MASK;
> +		tx_amp |= FIELD_PREP(PSGMII_QSGMII_TX_DRIVER_MASK, tx_driver_strength);
> +		ret = phy_write(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1, tx_amp);
> +	}

phy_modify() ?

> +
> +	return ret;
> +}
> +
> +static struct phy_driver qca807x_drivers[] = {
> +	{
> +		PHY_ID_MATCH_EXACT(PHY_ID_QCA8072),
> +		.name			= "Qualcomm QCA8072",
> +		.flags			= PHY_POLL_CABLE_TEST,
> +		/* PHY_GBIT_FEATURES */
> +		.probe			= qca807x_probe,
> +		.config_init		= qca807x_config,
> +		.read_status		= qca807x_read_status,
> +		.config_intr		= qca807x_config_intr,
> +		.handle_interrupt	= qca807x_handle_interrupt,
> +		.soft_reset		= genphy_soft_reset,
> +		.get_tunable		= qca807x_get_tunable,
> +		.set_tunable		= qca807x_set_tunable,
> +		.cable_test_start	= qca807x_cable_test_start,
> +		.cable_test_get_status	= qca807x_cable_test_get_status,
> +	},
> +	{
> +		PHY_ID_MATCH_EXACT(PHY_ID_QCA8075),
> +		.name			= "Qualcomm QCA8075",
> +		.flags			= PHY_POLL_CABLE_TEST,
> +		/* PHY_GBIT_FEATURES */
> +		.probe			= qca807x_probe,
> +		.config_init		= qca807x_config,
> +		.read_status		= qca807x_read_status,
> +		.config_intr		= qca807x_config_intr,
> +		.handle_interrupt	= qca807x_handle_interrupt,
> +		.soft_reset		= genphy_soft_reset,
> +		.get_tunable		= qca807x_get_tunable,
> +		.set_tunable		= qca807x_set_tunable,
> +		.cable_test_start	= qca807x_cable_test_start,
> +		.cable_test_get_status	= qca807x_cable_test_get_status,
> +	},
> +	{
> +		PHY_ID_MATCH_EXACT(PHY_ID_QCA807X_PSGMII),
> +		.name		= "Qualcomm QCA807x PSGMII",
> +		.probe		= qca807x_psgmii_config,
> +	},
> +};
> +module_phy_driver(qca807x_drivers);
> +
> +static struct mdio_device_id __maybe_unused qca807x_tbl[] = {
> +	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8072) },
> +	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8075) },
> +	{ PHY_ID_MATCH_MODEL(PHY_ID_QCA807X_PSGMII) },
> +	{ }
> +};
> +
> +MODULE_AUTHOR("Robert Marko");
> +MODULE_DESCRIPTION("Qualcomm QCA807x PHY driver");
> +MODULE_DEVICE_TABLE(mdio, qca807x_tbl);
> +MODULE_LICENSE("GPL");
> 

Re: [PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[-- Attachment #1: Type: text/plain, Size: 5034 bytes --]

Hi Robert,

I love your patch! Yet something to improve:

[auto build test ERROR on net-next/master]

url:    https://github.com/0day-ci/linux/commits/Robert-Marko/Add-support-for-Qualcomm-QCA807x-PHYs/20210210-210217
base:   https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git de1db4a6ed6241e34cab0e5059d4b56f6bae39b9
config: arm64-allyesconfig (attached as .config)
compiler: aarch64-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/0day-ci/linux/commit/bf3f094b38fe42c313ba63d67c21b64cffb7f7b1
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Robert-Marko/Add-support-for-Qualcomm-QCA807x-PHYs/20210210-210217
        git checkout bf3f094b38fe42c313ba63d67c21b64cffb7f7b1
        # save the attached .config to linux build tree
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=arm64 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>):

   drivers/net/phy/qca807x.c: In function 'qca807x_read_copper_status':
>> drivers/net/phy/qca807x.c:404:12: error: 'struct phy_device' has no member named 'port'
     404 |  if (phydev->port != PORT_TP)
         |            ^~
   drivers/net/phy/qca807x.c:405:9: error: 'struct phy_device' has no member named 'port'
     405 |   phydev->port = PORT_TP;
         |         ^~
   drivers/net/phy/qca807x.c: In function 'qca807x_read_fiber_status':
   drivers/net/phy/qca807x.c:494:12: error: 'struct phy_device' has no member named 'port'
     494 |  if (phydev->port != PORT_FIBRE)
         |            ^~
   drivers/net/phy/qca807x.c:495:9: error: 'struct phy_device' has no member named 'port'
     495 |   phydev->port = PORT_FIBRE;
         |         ^~


vim +404 drivers/net/phy/qca807x.c

   399	
   400	static int qca807x_read_copper_status(struct phy_device *phydev, bool combo_port)
   401	{
   402		int ss, err, page, old_link = phydev->link;
   403	
 > 404		if (phydev->port != PORT_TP)
   405			phydev->port = PORT_TP;
   406	
   407		/* Only combo port has dual pages */
   408		if (combo_port) {
   409			/* Check whether copper page is set and set if needed */
   410			page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
   411			if (!(page & QCA807X_BT_BX_REG_SEL)) {
   412				page |= QCA807X_BT_BX_REG_SEL;
   413				phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
   414			}
   415		}
   416	
   417		/* Update the link, but return if there was an error */
   418		err = genphy_update_link(phydev);
   419		if (err)
   420			return err;
   421	
   422		/* why bother the PHY if nothing can have changed */
   423		if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
   424			return 0;
   425	
   426		phydev->speed = SPEED_UNKNOWN;
   427		phydev->duplex = DUPLEX_UNKNOWN;
   428		phydev->pause = 0;
   429		phydev->asym_pause = 0;
   430	
   431		err = genphy_read_lpa(phydev);
   432		if (err < 0)
   433			return err;
   434	
   435		/* Read the QCA807x PHY-Specific Status register copper page,
   436		 * which indicates the speed and duplex that the PHY is actually
   437		 * using, irrespective of whether we are in autoneg mode or not.
   438		 */
   439		ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
   440		if (ss < 0)
   441			return ss;
   442	
   443		if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
   444			int sfc;
   445	
   446			sfc = phy_read(phydev, QCA807X_FUNCTION_CONTROL);
   447			if (sfc < 0)
   448				return sfc;
   449	
   450			switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
   451			case QCA807X_SS_SPEED_10:
   452				phydev->speed = SPEED_10;
   453				break;
   454			case QCA807X_SS_SPEED_100:
   455				phydev->speed = SPEED_100;
   456				break;
   457			case QCA807X_SS_SPEED_1000:
   458				phydev->speed = SPEED_1000;
   459				break;
   460			}
   461			if (ss & QCA807X_SS_DUPLEX)
   462				phydev->duplex = DUPLEX_FULL;
   463			else
   464				phydev->duplex = DUPLEX_HALF;
   465	
   466			if (ss & QCA807X_SS_MDIX)
   467				phydev->mdix = ETH_TP_MDI_X;
   468			else
   469				phydev->mdix = ETH_TP_MDI;
   470	
   471			switch (FIELD_GET(QCA807X_FC_MDI_CROSSOVER_MODE_MASK, sfc)) {
   472			case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI:
   473				phydev->mdix_ctrl = ETH_TP_MDI;
   474				break;
   475			case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX:
   476				phydev->mdix_ctrl = ETH_TP_MDI_X;
   477				break;
   478			case QCA807X_FC_MDI_CROSSOVER_AUTO:
   479				phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
   480				break;
   481			}
   482		}
   483	
   484		if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
   485			phy_resolve_aneg_pause(phydev);
   486	
   487		return 0;
   488	}
   489	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 76556 bytes --]

Re: [PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[kernel test robot]

[-- Attachment #1: Type: text/plain, Size: 5174 bytes --]

Hi Robert,

I love your patch! Yet something to improve:

[auto build test ERROR on net-next/master]

url:    https://github.com/0day-ci/linux/commits/Robert-Marko/Add-support-for-Qualcomm-QCA807x-PHYs/20210210-210217
base:   https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git de1db4a6ed6241e34cab0e5059d4b56f6bae39b9
config: arm64-allyesconfig (attached as .config)
compiler: aarch64-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/0day-ci/linux/commit/bf3f094b38fe42c313ba63d67c21b64cffb7f7b1
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Robert-Marko/Add-support-for-Qualcomm-QCA807x-PHYs/20210210-210217
        git checkout bf3f094b38fe42c313ba63d67c21b64cffb7f7b1
        # save the attached .config to linux build tree
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=arm64 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>):

   drivers/net/phy/qca807x.c: In function 'qca807x_read_copper_status':
>> drivers/net/phy/qca807x.c:404:12: error: 'struct phy_device' has no member named 'port'
     404 |  if (phydev->port != PORT_TP)
         |            ^~
   drivers/net/phy/qca807x.c:405:9: error: 'struct phy_device' has no member named 'port'
     405 |   phydev->port = PORT_TP;
         |         ^~
   drivers/net/phy/qca807x.c: In function 'qca807x_read_fiber_status':
   drivers/net/phy/qca807x.c:494:12: error: 'struct phy_device' has no member named 'port'
     494 |  if (phydev->port != PORT_FIBRE)
         |            ^~
   drivers/net/phy/qca807x.c:495:9: error: 'struct phy_device' has no member named 'port'
     495 |   phydev->port = PORT_FIBRE;
         |         ^~


vim +404 drivers/net/phy/qca807x.c

   399	
   400	static int qca807x_read_copper_status(struct phy_device *phydev, bool combo_port)
   401	{
   402		int ss, err, page, old_link = phydev->link;
   403	
 > 404		if (phydev->port != PORT_TP)
   405			phydev->port = PORT_TP;
   406	
   407		/* Only combo port has dual pages */
   408		if (combo_port) {
   409			/* Check whether copper page is set and set if needed */
   410			page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
   411			if (!(page & QCA807X_BT_BX_REG_SEL)) {
   412				page |= QCA807X_BT_BX_REG_SEL;
   413				phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
   414			}
   415		}
   416	
   417		/* Update the link, but return if there was an error */
   418		err = genphy_update_link(phydev);
   419		if (err)
   420			return err;
   421	
   422		/* why bother the PHY if nothing can have changed */
   423		if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
   424			return 0;
   425	
   426		phydev->speed = SPEED_UNKNOWN;
   427		phydev->duplex = DUPLEX_UNKNOWN;
   428		phydev->pause = 0;
   429		phydev->asym_pause = 0;
   430	
   431		err = genphy_read_lpa(phydev);
   432		if (err < 0)
   433			return err;
   434	
   435		/* Read the QCA807x PHY-Specific Status register copper page,
   436		 * which indicates the speed and duplex that the PHY is actually
   437		 * using, irrespective of whether we are in autoneg mode or not.
   438		 */
   439		ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
   440		if (ss < 0)
   441			return ss;
   442	
   443		if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
   444			int sfc;
   445	
   446			sfc = phy_read(phydev, QCA807X_FUNCTION_CONTROL);
   447			if (sfc < 0)
   448				return sfc;
   449	
   450			switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
   451			case QCA807X_SS_SPEED_10:
   452				phydev->speed = SPEED_10;
   453				break;
   454			case QCA807X_SS_SPEED_100:
   455				phydev->speed = SPEED_100;
   456				break;
   457			case QCA807X_SS_SPEED_1000:
   458				phydev->speed = SPEED_1000;
   459				break;
   460			}
   461			if (ss & QCA807X_SS_DUPLEX)
   462				phydev->duplex = DUPLEX_FULL;
   463			else
   464				phydev->duplex = DUPLEX_HALF;
   465	
   466			if (ss & QCA807X_SS_MDIX)
   467				phydev->mdix = ETH_TP_MDI_X;
   468			else
   469				phydev->mdix = ETH_TP_MDI;
   470	
   471			switch (FIELD_GET(QCA807X_FC_MDI_CROSSOVER_MODE_MASK, sfc)) {
   472			case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI:
   473				phydev->mdix_ctrl = ETH_TP_MDI;
   474				break;
   475			case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX:
   476				phydev->mdix_ctrl = ETH_TP_MDI_X;
   477				break;
   478			case QCA807X_FC_MDI_CROSSOVER_AUTO:
   479				phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
   480				break;
   481			}
   482		}
   483	
   484		if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
   485			phy_resolve_aneg_pause(phydev);
   486	
   487		return 0;
   488	}
   489	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org

[-- Attachment #2: config.gz --]
[-- Type: application/gzip, Size: 76556 bytes --]

Re: [PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[Andrew Lunn]

On Wed, Feb 10, 2021 at 01:55:22PM +0100, Robert Marko wrote:

Hi Robert

Could you move the GPIO driver into a patch of its own, and Cc: the
GPIO maintainer and list for that patch please.

     Andrew

Re: [PATCH v2 net-next 3/4] net: phy: Add Qualcomm QCA807x driver

[Andrew Lunn]

> +static int qca807x_psgmii_config(struct phy_device *phydev)
> +{
> +	struct device_node *node = phydev->mdio.dev.of_node;
> +	int psgmii_az, tx_amp, ret = 0;
> +	u32 tx_driver_strength_dt;
> +
> +	/* Workaround to enable AZ transmitting ability */
> +	if (of_property_read_bool(node, "qcom,psgmii-az")) {
> +		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
> +		psgmii_az &= ~PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK;
> +		psgmii_az |= FIELD_PREP(PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK, 0xc);
> +		ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL, psgmii_az);
> +		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
> +	}
> +
> +	/* PSGMII/QSGMII TX amp set to DT defined value instead of default 600mV */
> +	if (!of_property_read_u32(node, "qcom,tx-driver-strength", &tx_driver_strength_dt)) {
> +		int tx_driver_strength;
> +
> +		switch (tx_driver_strength_dt) {
> +		case 140:
> +			tx_driver_strength = 0;
> +			break;
> +		case 160:
> +			tx_driver_strength = 1;
> +			break;
> +		case 180:
> +			tx_driver_strength = 2;
> +			break;
> +		case 200:
> +			tx_driver_strength = 3;
> +			break;
> +		case 220:
> +			tx_driver_strength = 4;
> +			break;
> +		case 240:
> +			tx_driver_strength = 5;
> +			break;
> +		case 260:
> +			tx_driver_strength = 6;
> +			break;
> +		case 280:
> +			tx_driver_strength = 7;
> +			break;
> +		case 300:
> +			tx_driver_strength = 8;
> +			break;
> +		case 320:
> +			tx_driver_strength = 9;
> +			break;
> +		case 400:
> +			tx_driver_strength = 10;
> +			break;
> +		case 500:
> +			tx_driver_strength = 11;
> +			break;
> +		case 600:
> +			tx_driver_strength = 12;
> +			break;
> +		default:
> +			tx_driver_strength = 12;
> +			break;

Please return -EINVAL here. The value in DT is not valid, so you
should error out. If there is no value at all, then it is O.K. to
default to 12.

     Andrew

[PATCH v2 net-next 4/4] MAINTAINERS: Add entry for Qualcomm QCA807x PHY driver

[Robert Marko]

Add maintainers entry for the Qualcomm QCA807x PHY driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
 MAINTAINERS | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 667d03852191..48f32ef108d5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14775,6 +14775,15 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/regulator/vqmmc-ipq4019-regulator.yaml
 F:	drivers/regulator/vqmmc-ipq4019-regulator.c
 
+QUALCOMM QCA807X PHY DRIVER
+M:	Robert Marko <robert.marko@sartura.hr>
+M:	Luka Perkov <luka.perkov@sartura.hr>
+L:	linux-arm-msm@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/qcom,qca807x.yaml
+F:	drivers/net/phy/qca807x.c
+F:	include/dt-bindings/net/qcom-qca807x.h
+
 QUALCOMM RMNET DRIVER
 M:	Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
 M:	Sean Tranchetti <stranche@codeaurora.org>
-- 
2.29.2