* [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR
@ 2021-02-12 13:56 Peter Bergin
2021-02-12 18:16 ` ZHIZHIKIN Andrey
0 siblings, 1 reply; 3+ messages in thread
From: Peter Bergin @ 2021-02-12 13:56 UTC (permalink / raw)
To: u-boot
Update imx-atf and firmware-imx to latest released versions.
Update address of ATF_LOAD_ADDR that has changed to 0x490000 in imx-atf
commit 48733cb4e773a7584ced601de9d717efa3d73815.
Add 'O=' to make instructions as one issue has been noticed where it was
trouble building directly inside u-boot source dir.
Signed-off-by: Peter Bergin <peter@berginkonsult.se>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
---
doc/board/freescale/imx8mp_evk.rst | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/doc/board/freescale/imx8mp_evk.rst b/doc/board/freescale/imx8mp_evk.rst
index ccffcf7257..5ca3bb8199 100644
--- a/doc/board/freescale/imx8mp_evk.rst
+++ b/doc/board/freescale/imx8mp_evk.rst
@@ -18,7 +18,7 @@ Get and Build the ARM Trusted firmware
Note: $(srctree) is the U-Boot source directory
Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_5.4.47_2.2.0
+branch: imx_5.4.70_2.3.0
.. code-block:: bash
@@ -30,13 +30,13 @@ Get the ddr firmware
.. code-block:: bash
- $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
- $ chmod +x firmware-imx-8.9.bin
- $ ./firmware-imx-8.9.bin
- $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_1d_dmem.bin
- $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin $(srctree)/lpddr4_pmu_train_1d_imem.bin
- $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_2d_dmem.bin
- $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
+ $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.bin
+ $ chmod +x firmware-imx-8.10.bin
+ $ ./firmware-imx-8.10.bin
+ $ cp firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin $(srctree)/lpddr4_pmu_train_1d_dmem.bin
+ $ cp firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin $(srctree)/lpddr4_pmu_train_1d_imem.bin
+ $ cp firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin $(srctree)/lpddr4_pmu_train_2d_dmem.bin
+ $ cp firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_202006.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
Build U-Boot
------------
@@ -44,15 +44,15 @@ Build U-Boot
.. code-block:: bash
$ export CROSS_COMPILE=aarch64-poky-linux-
- $ make imx8mp_evk_defconfig
- $ export ATF_LOAD_ADDR=0x960000
- $ make flash.bin
+ $ make O=build imx8mp_evk_defconfig
+ $ export ATF_LOAD_ADDR=0x970000
+ $ make O=build flash.bin
Burn the flash.bin to the MicroSD card at offset 32KB:
.. code-block:: bash
- $sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
+ $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
Boot
----
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR
2021-02-12 13:56 [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR Peter Bergin
@ 2021-02-12 18:16 ` ZHIZHIKIN Andrey
2021-02-12 19:38 ` Peter Bergin
0 siblings, 1 reply; 3+ messages in thread
From: ZHIZHIKIN Andrey @ 2021-02-12 18:16 UTC (permalink / raw)
To: u-boot
Hello Peter,
> -----Original Message-----
> From: Peter Bergin <peter@berginkonsult.se>
> Sent: Friday, February 12, 2021 2:57 PM
> To: u-boot at lists.denx.de
> Cc: Peter Bergin <peter@berginkonsult.se>; ZHIZHIKIN Andrey
> <andrey.zhizhikin@leica-geosystems.com>
> Subject: [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions
> and change ATF_LOAD_ADDR
>
> Update imx-atf and firmware-imx to latest released versions.
>
> Update address of ATF_LOAD_ADDR that has changed to 0x490000 in imx-atf
> commit 48733cb4e773a7584ced601de9d717efa3d73815.
Commit message is incorrect, ATF_LOAD_ADDR is actually set to 0x970000
>
> Add 'O=' to make instructions as one issue has been noticed where it was trouble
> building directly inside u-boot source dir.
>
> Signed-off-by: Peter Bergin <peter@berginkonsult.se>
> Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
> ---
> doc/board/freescale/imx8mp_evk.rst | 24 ++++++++++++------------
> 1 file changed, 12 insertions(+), 12 deletions(-)
>
> diff --git a/doc/board/freescale/imx8mp_evk.rst
> b/doc/board/freescale/imx8mp_evk.rst
> index ccffcf7257..5ca3bb8199 100644
> --- a/doc/board/freescale/imx8mp_evk.rst
> +++ b/doc/board/freescale/imx8mp_evk.rst
> @@ -18,7 +18,7 @@ Get and Build the ARM Trusted firmware
>
> Note: $(srctree) is the U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
> -branch: imx_5.4.47_2.2.0
> +branch: imx_5.4.70_2.3.0
>
> .. code-block:: bash
>
> @@ -30,13 +30,13 @@ Get the ddr firmware
>
> .. code-block:: bash
>
> - $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
> - $ chmod +x firmware-imx-8.9.bin
> - $ ./firmware-imx-8.9.bin
> - $ cp firmware-imx-
> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin
> $(srctree)/lpddr4_pmu_train_1d_dmem.bin
> - $ cp firmware-imx-
> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin
> $(srctree)/lpddr4_pmu_train_1d_imem.bin
> - $ cp firmware-imx-
> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin
> $(srctree)/lpddr4_pmu_train_2d_dmem.bin
> - $ cp firmware-imx-
> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin
> $(srctree)/lpddr4_pmu_train_2d_imem.bin
> + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.bin
> + $ chmod +x firmware-imx-8.10.bin
> + $ ./firmware-imx-8.10.bin
> + $ cp firmware-imx-
> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin
> $(srctree)/lpddr4_pmu_train_1d_dmem.bin
> + $ cp firmware-imx-
> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin
> $(srctree)/lpddr4_pmu_train_1d_imem.bin
> + $ cp firmware-imx-
> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin
> $(srctree)/lpddr4_pmu_train_2d_dmem.bin
> + $ cp
> + firmware-imx-
> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_20200
> + 6.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
>
> Build U-Boot
> ------------
> @@ -44,15 +44,15 @@ Build U-Boot
> .. code-block:: bash
>
> $ export CROSS_COMPILE=aarch64-poky-linux-
> - $ make imx8mp_evk_defconfig
> - $ export ATF_LOAD_ADDR=0x960000
> - $ make flash.bin
> + $ make O=build imx8mp_evk_defconfig
As a suggestion: maybe it is better to change the order here when `make O=build imx8mp_evk_defconfig` called first, followed by copy of DDR firmware and ATF binary.
This would make sure that the ./build folder would already exist at the time copy operations are executed, and should make step-by-step instructions more transparent.
> + $ export ATF_LOAD_ADDR=0x970000
> + $ make O=build flash.bin
>
> Burn the flash.bin to the MicroSD card at offset 32KB:
>
> .. code-block:: bash
>
> - $sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
> + $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32
> + conv=notrunc; sync
>
> Boot
> ----
> --
> 2.25.1
Otherwise:
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cheers,
Andrey
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR
2021-02-12 18:16 ` ZHIZHIKIN Andrey
@ 2021-02-12 19:38 ` Peter Bergin
0 siblings, 0 replies; 3+ messages in thread
From: Peter Bergin @ 2021-02-12 19:38 UTC (permalink / raw)
To: u-boot
Hi Andrey,
thanks for the review!
On 2021-02-12 19:16, ZHIZHIKIN Andrey wrote:
> Hello Peter,
>
>> -----Original Message-----
>> From: Peter Bergin <peter@berginkonsult.se>
>> Sent: Friday, February 12, 2021 2:57 PM
>> To: u-boot at lists.denx.de
>> Cc: Peter Bergin <peter@berginkonsult.se>; ZHIZHIKIN Andrey
>> <andrey.zhizhikin@leica-geosystems.com>
>> Subject: [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions
>> and change ATF_LOAD_ADDR
>>
>> Update imx-atf and firmware-imx to latest released versions.
>>
>> Update address of ATF_LOAD_ADDR that has changed to 0x490000 in imx-atf
>> commit 48733cb4e773a7584ced601de9d717efa3d73815.
> Commit message is incorrect, ATF_LOAD_ADDR is actually set to 0x970000
Good catch and it is indeed wrong.
>> Add 'O=' to make instructions as one issue has been noticed where it was trouble
>> building directly inside u-boot source dir.
>>
>> Signed-off-by: Peter Bergin <peter@berginkonsult.se>
>> Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
>> ---
>> doc/board/freescale/imx8mp_evk.rst | 24 ++++++++++++------------
>> 1 file changed, 12 insertions(+), 12 deletions(-)
>>
>> diff --git a/doc/board/freescale/imx8mp_evk.rst
>> b/doc/board/freescale/imx8mp_evk.rst
>> index ccffcf7257..5ca3bb8199 100644
>> --- a/doc/board/freescale/imx8mp_evk.rst
>> +++ b/doc/board/freescale/imx8mp_evk.rst
>> @@ -18,7 +18,7 @@ Get and Build the ARM Trusted firmware
>>
>> Note: $(srctree) is the U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
>> -branch: imx_5.4.47_2.2.0
>> +branch: imx_5.4.70_2.3.0
>>
>> .. code-block:: bash
>>
>> @@ -30,13 +30,13 @@ Get the ddr firmware
>>
>> .. code-block:: bash
>>
>> - $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
>> - $ chmod +x firmware-imx-8.9.bin
>> - $ ./firmware-imx-8.9.bin
>> - $ cp firmware-imx-
>> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin
>> $(srctree)/lpddr4_pmu_train_1d_dmem.bin
>> - $ cp firmware-imx-
>> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin
>> $(srctree)/lpddr4_pmu_train_1d_imem.bin
>> - $ cp firmware-imx-
>> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin
>> $(srctree)/lpddr4_pmu_train_2d_dmem.bin
>> - $ cp firmware-imx-
>> 8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin
>> $(srctree)/lpddr4_pmu_train_2d_imem.bin
>> + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.bin
>> + $ chmod +x firmware-imx-8.10.bin
>> + $ ./firmware-imx-8.10.bin
>> + $ cp firmware-imx-
>> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin
>> $(srctree)/lpddr4_pmu_train_1d_dmem.bin
>> + $ cp firmware-imx-
>> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin
>> $(srctree)/lpddr4_pmu_train_1d_imem.bin
>> + $ cp firmware-imx-
>> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin
>> $(srctree)/lpddr4_pmu_train_2d_dmem.bin
>> + $ cp
>> + firmware-imx-
>> 8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_20200
>> + 6.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
>> Build U-Boot
>> ------------
>> @@ -44,15 +44,15 @@ Build U-Boot
>> .. code-block:: bash
>>
>> $ export CROSS_COMPILE=aarch64-poky-linux-
>> - $ make imx8mp_evk_defconfig
>> - $ export ATF_LOAD_ADDR=0x960000
>> - $ make flash.bin
>> + $ make O=build imx8mp_evk_defconfig
> As a suggestion: maybe it is better to change the order here when `make O=build imx8mp_evk_defconfig` called first, followed by copy of DDR firmware and ATF binary.
>
> This would make sure that the ./build folder would already exist at the time copy operations are executed, and should make step-by-step instructions more transparent.
Good suggestion.
>> + $ export ATF_LOAD_ADDR=0x970000
>> + $ make O=build flash.bin
>>
>> Burn the flash.bin to the MicroSD card at offset 32KB:
>>
>> .. code-block:: bash
>>
>> - $sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
>> + $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32
>> + conv=notrunc; sync
>>
>> Boot
>> ----
>> --
>> 2.25.1
> Otherwise:
> Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
>
> Cheers,
> Andrey
Will update and send a v2 on this.
Best regards,
/Peter
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-02-12 19:38 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-02-12 13:56 [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR Peter Bergin
2021-02-12 18:16 ` ZHIZHIKIN Andrey
2021-02-12 19:38 ` Peter Bergin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.