From: Aswath Govindraju <a-govindraju@ti.com>
To: unlisted-recipients:; (no To-header on input)
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
Lokesh Vutla <lokeshvutla@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>, <a-govindraju@ti.com>,
Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
Date: Wed, 10 Mar 2021 21:49:23 +0530 [thread overview]
Message-ID: <20210310161924.22256-4-a-govindraju@ti.com> (raw)
In-Reply-To: <20210310161924.22256-1-a-govindraju@ti.com>
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the latest J7200 datasheet[2]
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
[2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
2 files changed, 54 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..6f90c3b1cf45 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,29 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_sd_dv";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -45,6 +68,13 @@
};
&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +100,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -157,6 +193,10 @@
};
&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
@@ -206,6 +246,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
ti,otap-del-sel-mmc-hs = <0x0>;
ti,otap-del-sel-ddr52 = <0x6>;
ti,otap-del-sel-hs200 = <0x8>;
- ti,otap-del-sel-hs400 = <0x0>;
+ ti,otap-del-sel-hs400 = <0x5>;
+ ti,itap-del-sel-legacy = <0x10>;
+ ti,itap-del-sel-mmc-hs = <0xa>;
ti,strobe-sel = <0x77>;
+ ti,clkbuf-sel = <0x7>;
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -534,7 +539,12 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ ti,trm-icp = <0x8>;
dma-coherent;
};
--
2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Aswath Govindraju <a-govindraju@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
Lokesh Vutla <lokeshvutla@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>, <a-govindraju@ti.com>,
Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
Date: Wed, 10 Mar 2021 21:49:23 +0530 [thread overview]
Message-ID: <20210310161924.22256-4-a-govindraju@ti.com> (raw)
In-Reply-To: <20210310161924.22256-1-a-govindraju@ti.com>
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the latest J7200 datasheet[2]
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
[2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
2 files changed, 54 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..6f90c3b1cf45 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,29 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_sd_dv";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -45,6 +68,13 @@
};
&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +100,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -157,6 +193,10 @@
};
&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
@@ -206,6 +246,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
ti,otap-del-sel-mmc-hs = <0x0>;
ti,otap-del-sel-ddr52 = <0x6>;
ti,otap-del-sel-hs200 = <0x8>;
- ti,otap-del-sel-hs400 = <0x0>;
+ ti,otap-del-sel-hs400 = <0x5>;
+ ti,itap-del-sel-legacy = <0x10>;
+ ti,itap-del-sel-mmc-hs = <0xa>;
ti,strobe-sel = <0x77>;
+ ti,clkbuf-sel = <0x7>;
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -534,7 +539,12 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ ti,trm-icp = <0x8>;
dma-coherent;
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-03-10 16:20 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-10 16:19 [PATCH v5 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems Aswath Govindraju
2021-03-10 16:19 ` Aswath Govindraju
2021-03-10 16:19 ` [PATCH v5 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes Aswath Govindraju
2021-03-10 16:19 ` Aswath Govindraju
2021-03-11 12:30 ` Grygorii Strashko
2021-03-11 12:30 ` Grygorii Strashko
2021-03-10 16:19 ` [PATCH v5 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules Aswath Govindraju
2021-03-10 16:19 ` Aswath Govindraju
2021-03-16 12:01 ` Grygorii Strashko
2021-03-16 12:01 ` Grygorii Strashko
2021-03-10 16:19 ` Aswath Govindraju [this message]
2021-03-10 16:19 ` [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems Aswath Govindraju
2021-03-18 15:15 ` Kishon Vijay Abraham I
2021-03-18 15:15 ` Kishon Vijay Abraham I
2021-03-19 3:45 ` Aswath Govindraju
2021-03-19 3:45 ` Aswath Govindraju
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210310161924.22256-4-a-govindraju@ti.com \
--to=a-govindraju@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=kristo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.