From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> To: vkoul@kernel.org Cc: yung-chuan.liao@linux.intel.com, pierre-louis.bossart@linux.intel.com, sanyog.r.kale@intel.com, alsa-devel@alsa-project.org, linux-kernel@vger.kernel.org, robh@kernel.org, devicetree@vger.kernel.org, Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Subject: [PATCH v4 5/9] soundwire: qcom: update register read/write routine Date: Fri, 12 Mar 2021 12:00:05 +0000 [thread overview] Message-ID: <20210312120009.22386-6-srinivas.kandagatla@linaro.org> (raw) In-Reply-To: <20210312120009.22386-1-srinivas.kandagatla@linaro.org> In the existing code every soundwire register read and register write are kinda blocked. Each of these are using a special command id that generates interrupt after it successfully finishes. This is really overhead, limiting and not really necessary unless we are doing something special. We can simply read/write the fifo that should also give exactly what we need! This will also allow to read/write registers in interrupt context, which was not possible with the special command approach. With previous approach number of interrupts generated after enumeration are around 130: $ cat /proc/interrupts | grep soundwire 21: 130 0 0 0 0 0 0 0 GICv3 234 Edge soundwire after this patch they are just 3 interrupts $ cat /proc/interrupts | grep soundwire 21: 3 0 0 0 0 0 0 0 GICv3 234 Edge soundwire This has significantly not only reduced interrupting CPU during enumeration but also during streaming! Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- drivers/soundwire/qcom.c | 178 ++++++++++++++++++++++----------------- 1 file changed, 99 insertions(+), 79 deletions(-) diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c index 2bcb4362f0e0..0cbd611fb8c6 100644 --- a/drivers/soundwire/qcom.c +++ b/drivers/soundwire/qcom.c @@ -38,11 +38,13 @@ #define SWRM_CMD_FIFO_WR_CMD 0x300 #define SWRM_CMD_FIFO_RD_CMD 0x304 #define SWRM_CMD_FIFO_CMD 0x308 +#define SWRM_CMD_FIFO_FLUSH 0x1 #define SWRM_CMD_FIFO_STATUS 0x30C #define SWRM_CMD_FIFO_CFG_ADDR 0x314 #define SWRM_CONTINUE_EXEC_ON_CMD_IGNORE BIT(31) #define SWRM_RD_WR_CMD_RETRIES 0x7 #define SWRM_CMD_FIFO_RD_FIFO_ADDR 0x318 +#define SWRM_RD_FIFO_CMD_ID_MASK GENMASK(11, 8) #define SWRM_ENUMERATOR_CFG_ADDR 0x500 #define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m) (0x101C + 0x40 * (m)) #define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK GENMASK(2, 0) @@ -78,13 +80,16 @@ #define SWRM_SPECIAL_CMD_ID 0xF #define MAX_FREQ_NUM 1 #define TIMEOUT_MS (2 * HZ) -#define QCOM_SWRM_MAX_RD_LEN 0xf +#define QCOM_SWRM_MAX_RD_LEN 0x1 #define QCOM_SDW_MAX_PORTS 14 #define DEFAULT_CLK_FREQ 9600000 #define SWRM_MAX_DAIS 0xF #define SWR_INVALID_PARAM 0xFF #define SWR_HSTOP_MAX_VAL 0xF #define SWR_HSTART_MIN_VAL 0x0 +#define SWR_BROADCAST_CMD_ID 0x0F +#define SWR_MAX_CMD_ID 14 +#define MAX_FIFO_RD_RETRY 3 struct qcom_swrm_port_config { u8 si; @@ -103,10 +108,8 @@ struct qcom_swrm_ctrl { struct device *dev; struct regmap *regmap; void __iomem *mmio; - struct completion *comp; + struct completion broadcast; struct work_struct slave_work; - /* read/write lock */ - spinlock_t comp_lock; /* Port alloc/free lock */ struct mutex port_lock; struct clk *hclk; @@ -120,6 +123,8 @@ struct qcom_swrm_ctrl { int rows_index; unsigned long dout_port_mask; unsigned long din_port_mask; + u8 rcmd_id; + u8 wcmd_id; struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS]; struct sdw_stream_runtime *sruntime[SWRM_MAX_DAIS]; enum sdw_slave_status status[SDW_MAX_DEVICES]; @@ -198,77 +203,105 @@ static int qcom_swrm_cpu_reg_write(struct qcom_swrm_ctrl *ctrl, int reg, return SDW_CMD_OK; } -static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *ctrl, u8 cmd_data, - u8 dev_addr, u16 reg_addr) +static u32 swrm_get_packed_reg_val(u8 *cmd_id, u8 cmd_data, + u8 dev_addr, u16 reg_addr) { - DECLARE_COMPLETION_ONSTACK(comp); - unsigned long flags; u32 val; - int ret; - - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = ∁ - spin_unlock_irqrestore(&ctrl->comp_lock, flags); - val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, - SWRM_SPECIAL_CMD_ID, reg_addr); - ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_WR_CMD, val); - if (ret) - goto err; - - ret = wait_for_completion_timeout(ctrl->comp, - msecs_to_jiffies(TIMEOUT_MS)); + u8 id = *cmd_id; - if (!ret) - ret = SDW_CMD_IGNORED; - else - ret = SDW_CMD_OK; -err: - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = NULL; - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + if (id != SWR_BROADCAST_CMD_ID) { + if (id < SWR_MAX_CMD_ID) + id += 1; + else + id = 0; + *cmd_id = id; + } + val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, id, reg_addr); - return ret; + return val; } -static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *ctrl, - u8 dev_addr, u16 reg_addr, - u32 len, u8 *rval) + +static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *swrm, u8 cmd_data, + u8 dev_addr, u16 reg_addr) { - int i, ret; - u32 val; - DECLARE_COMPLETION_ONSTACK(comp); - unsigned long flags; - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = ∁ - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + u32 val; + int ret = 0; + u8 cmd_id = 0x0; - val = SWRM_REG_VAL_PACK(len, dev_addr, SWRM_SPECIAL_CMD_ID, reg_addr); - ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_RD_CMD, val); - if (ret) - goto err; + if (dev_addr == SDW_BROADCAST_DEV_NUM) { + cmd_id = SWR_BROADCAST_CMD_ID; + val = swrm_get_packed_reg_val(&cmd_id, cmd_data, + dev_addr, reg_addr); + } else { + val = swrm_get_packed_reg_val(&swrm->wcmd_id, cmd_data, + dev_addr, reg_addr); + } - ret = wait_for_completion_timeout(ctrl->comp, - msecs_to_jiffies(TIMEOUT_MS)); + swrm->reg_write(swrm, SWRM_CMD_FIFO_WR_CMD, val); + + /* version 1.3 or less */ + if (swrm->version <= 0x01030000) + usleep_range(150, 155); + + if (cmd_id == SWR_BROADCAST_CMD_ID) { + /* + * sleep for 10ms for MSM soundwire variant to allow broadcast + * command to complete. + */ + ret = wait_for_completion_timeout(&swrm->broadcast, + msecs_to_jiffies(TIMEOUT_MS)); + if (!ret) + ret = SDW_CMD_IGNORED; + else + ret = SDW_CMD_OK; - if (!ret) { - ret = SDW_CMD_IGNORED; - goto err; } else { ret = SDW_CMD_OK; } + return ret; +} - for (i = 0; i < len; i++) { - ctrl->reg_read(ctrl, SWRM_CMD_FIFO_RD_FIFO_ADDR, &val); - rval[i] = val & 0xFF; - } +static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *swrm, + u8 dev_addr, u16 reg_addr, + u32 len, u8 *rval) +{ + u32 cmd_data, cmd_id, val, retry_attempt = 0; + + val = swrm_get_packed_reg_val(&swrm->rcmd_id, len, dev_addr, reg_addr); + + /* wait for FIFO RD to complete to avoid overflow */ + usleep_range(100, 105); + swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val); + /* wait for FIFO RD CMD complete to avoid overflow */ + usleep_range(250, 255); + + do { + swrm->reg_read(swrm, SWRM_CMD_FIFO_RD_FIFO_ADDR, &cmd_data); + rval[0] = cmd_data & 0xFF; + cmd_id = FIELD_GET(SWRM_RD_FIFO_CMD_ID_MASK, cmd_data); + + if (cmd_id != swrm->rcmd_id) { + if (retry_attempt < (MAX_FIFO_RD_RETRY - 1)) { + /* wait 500 us before retry on fifo read failure */ + usleep_range(500, 505); + swrm->reg_write(swrm, SWRM_CMD_FIFO_CMD, + SWRM_CMD_FIFO_FLUSH); + swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val); + } + retry_attempt++; + } else { + return SDW_CMD_OK; + } -err: - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = NULL; - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + } while (retry_attempt < MAX_FIFO_RD_RETRY); - return ret; + dev_err(swrm->dev, "failed to read fifo: reg: 0x%x, rcmd_id: 0x%x,\ + dev_num: 0x%x, cmd_data: 0x%x\n", + reg_addr, swrm->rcmd_id, dev_addr, cmd_data); + + return SDW_CMD_IGNORED; } static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl) @@ -291,7 +324,6 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) { struct qcom_swrm_ctrl *ctrl = dev_id; u32 sts, value; - unsigned long flags; ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS, &sts); @@ -304,8 +336,10 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) } if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) || - sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) - schedule_work(&ctrl->slave_work); + sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) { + qcom_swrm_get_device_status(ctrl); + sdw_handle_slave_status(&ctrl->bus, ctrl->status); + } /** * clear the interrupt before complete() is called, as complete can @@ -314,15 +348,12 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) */ ctrl->reg_write(ctrl, SWRM_INTERRUPT_CLEAR, sts); - if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED) { - spin_lock_irqsave(&ctrl->comp_lock, flags); - if (ctrl->comp) - complete(ctrl->comp); - spin_unlock_irqrestore(&ctrl->comp_lock, flags); - } + if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED) + complete(&ctrl->broadcast); return IRQ_HANDLED; } + static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl) { u32 val; @@ -570,16 +601,6 @@ static u32 qcom_swrm_freq_tbl[MAX_FREQ_NUM] = { DEFAULT_CLK_FREQ, }; -static void qcom_swrm_slave_wq(struct work_struct *work) -{ - struct qcom_swrm_ctrl *ctrl = - container_of(work, struct qcom_swrm_ctrl, slave_work); - - qcom_swrm_get_device_status(ctrl); - sdw_handle_slave_status(&ctrl->bus, ctrl->status); -} - - static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl, struct sdw_stream_runtime *stream) { @@ -947,9 +968,8 @@ static int qcom_swrm_probe(struct platform_device *pdev) ctrl->dev = dev; dev_set_drvdata(&pdev->dev, ctrl); - spin_lock_init(&ctrl->comp_lock); mutex_init(&ctrl->port_lock); - INIT_WORK(&ctrl->slave_work, qcom_swrm_slave_wq); + init_completion(&ctrl->broadcast); ctrl->bus.ops = &qcom_swrm_ops; ctrl->bus.port_ops = &qcom_swrm_port_ops; -- 2.21.0
WARNING: multiple messages have this Message-ID (diff)
From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> To: vkoul@kernel.org Cc: robh@kernel.org, alsa-devel@alsa-project.org, devicetree@vger.kernel.org, pierre-louis.bossart@linux.intel.com, linux-kernel@vger.kernel.org, Srinivas Kandagatla <srinivas.kandagatla@linaro.org>, sanyog.r.kale@intel.com, yung-chuan.liao@linux.intel.com Subject: [PATCH v4 5/9] soundwire: qcom: update register read/write routine Date: Fri, 12 Mar 2021 12:00:05 +0000 [thread overview] Message-ID: <20210312120009.22386-6-srinivas.kandagatla@linaro.org> (raw) In-Reply-To: <20210312120009.22386-1-srinivas.kandagatla@linaro.org> In the existing code every soundwire register read and register write are kinda blocked. Each of these are using a special command id that generates interrupt after it successfully finishes. This is really overhead, limiting and not really necessary unless we are doing something special. We can simply read/write the fifo that should also give exactly what we need! This will also allow to read/write registers in interrupt context, which was not possible with the special command approach. With previous approach number of interrupts generated after enumeration are around 130: $ cat /proc/interrupts | grep soundwire 21: 130 0 0 0 0 0 0 0 GICv3 234 Edge soundwire after this patch they are just 3 interrupts $ cat /proc/interrupts | grep soundwire 21: 3 0 0 0 0 0 0 0 GICv3 234 Edge soundwire This has significantly not only reduced interrupting CPU during enumeration but also during streaming! Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- drivers/soundwire/qcom.c | 178 ++++++++++++++++++++++----------------- 1 file changed, 99 insertions(+), 79 deletions(-) diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c index 2bcb4362f0e0..0cbd611fb8c6 100644 --- a/drivers/soundwire/qcom.c +++ b/drivers/soundwire/qcom.c @@ -38,11 +38,13 @@ #define SWRM_CMD_FIFO_WR_CMD 0x300 #define SWRM_CMD_FIFO_RD_CMD 0x304 #define SWRM_CMD_FIFO_CMD 0x308 +#define SWRM_CMD_FIFO_FLUSH 0x1 #define SWRM_CMD_FIFO_STATUS 0x30C #define SWRM_CMD_FIFO_CFG_ADDR 0x314 #define SWRM_CONTINUE_EXEC_ON_CMD_IGNORE BIT(31) #define SWRM_RD_WR_CMD_RETRIES 0x7 #define SWRM_CMD_FIFO_RD_FIFO_ADDR 0x318 +#define SWRM_RD_FIFO_CMD_ID_MASK GENMASK(11, 8) #define SWRM_ENUMERATOR_CFG_ADDR 0x500 #define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m) (0x101C + 0x40 * (m)) #define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK GENMASK(2, 0) @@ -78,13 +80,16 @@ #define SWRM_SPECIAL_CMD_ID 0xF #define MAX_FREQ_NUM 1 #define TIMEOUT_MS (2 * HZ) -#define QCOM_SWRM_MAX_RD_LEN 0xf +#define QCOM_SWRM_MAX_RD_LEN 0x1 #define QCOM_SDW_MAX_PORTS 14 #define DEFAULT_CLK_FREQ 9600000 #define SWRM_MAX_DAIS 0xF #define SWR_INVALID_PARAM 0xFF #define SWR_HSTOP_MAX_VAL 0xF #define SWR_HSTART_MIN_VAL 0x0 +#define SWR_BROADCAST_CMD_ID 0x0F +#define SWR_MAX_CMD_ID 14 +#define MAX_FIFO_RD_RETRY 3 struct qcom_swrm_port_config { u8 si; @@ -103,10 +108,8 @@ struct qcom_swrm_ctrl { struct device *dev; struct regmap *regmap; void __iomem *mmio; - struct completion *comp; + struct completion broadcast; struct work_struct slave_work; - /* read/write lock */ - spinlock_t comp_lock; /* Port alloc/free lock */ struct mutex port_lock; struct clk *hclk; @@ -120,6 +123,8 @@ struct qcom_swrm_ctrl { int rows_index; unsigned long dout_port_mask; unsigned long din_port_mask; + u8 rcmd_id; + u8 wcmd_id; struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS]; struct sdw_stream_runtime *sruntime[SWRM_MAX_DAIS]; enum sdw_slave_status status[SDW_MAX_DEVICES]; @@ -198,77 +203,105 @@ static int qcom_swrm_cpu_reg_write(struct qcom_swrm_ctrl *ctrl, int reg, return SDW_CMD_OK; } -static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *ctrl, u8 cmd_data, - u8 dev_addr, u16 reg_addr) +static u32 swrm_get_packed_reg_val(u8 *cmd_id, u8 cmd_data, + u8 dev_addr, u16 reg_addr) { - DECLARE_COMPLETION_ONSTACK(comp); - unsigned long flags; u32 val; - int ret; - - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = ∁ - spin_unlock_irqrestore(&ctrl->comp_lock, flags); - val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, - SWRM_SPECIAL_CMD_ID, reg_addr); - ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_WR_CMD, val); - if (ret) - goto err; - - ret = wait_for_completion_timeout(ctrl->comp, - msecs_to_jiffies(TIMEOUT_MS)); + u8 id = *cmd_id; - if (!ret) - ret = SDW_CMD_IGNORED; - else - ret = SDW_CMD_OK; -err: - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = NULL; - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + if (id != SWR_BROADCAST_CMD_ID) { + if (id < SWR_MAX_CMD_ID) + id += 1; + else + id = 0; + *cmd_id = id; + } + val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, id, reg_addr); - return ret; + return val; } -static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *ctrl, - u8 dev_addr, u16 reg_addr, - u32 len, u8 *rval) + +static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *swrm, u8 cmd_data, + u8 dev_addr, u16 reg_addr) { - int i, ret; - u32 val; - DECLARE_COMPLETION_ONSTACK(comp); - unsigned long flags; - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = ∁ - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + u32 val; + int ret = 0; + u8 cmd_id = 0x0; - val = SWRM_REG_VAL_PACK(len, dev_addr, SWRM_SPECIAL_CMD_ID, reg_addr); - ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_RD_CMD, val); - if (ret) - goto err; + if (dev_addr == SDW_BROADCAST_DEV_NUM) { + cmd_id = SWR_BROADCAST_CMD_ID; + val = swrm_get_packed_reg_val(&cmd_id, cmd_data, + dev_addr, reg_addr); + } else { + val = swrm_get_packed_reg_val(&swrm->wcmd_id, cmd_data, + dev_addr, reg_addr); + } - ret = wait_for_completion_timeout(ctrl->comp, - msecs_to_jiffies(TIMEOUT_MS)); + swrm->reg_write(swrm, SWRM_CMD_FIFO_WR_CMD, val); + + /* version 1.3 or less */ + if (swrm->version <= 0x01030000) + usleep_range(150, 155); + + if (cmd_id == SWR_BROADCAST_CMD_ID) { + /* + * sleep for 10ms for MSM soundwire variant to allow broadcast + * command to complete. + */ + ret = wait_for_completion_timeout(&swrm->broadcast, + msecs_to_jiffies(TIMEOUT_MS)); + if (!ret) + ret = SDW_CMD_IGNORED; + else + ret = SDW_CMD_OK; - if (!ret) { - ret = SDW_CMD_IGNORED; - goto err; } else { ret = SDW_CMD_OK; } + return ret; +} - for (i = 0; i < len; i++) { - ctrl->reg_read(ctrl, SWRM_CMD_FIFO_RD_FIFO_ADDR, &val); - rval[i] = val & 0xFF; - } +static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *swrm, + u8 dev_addr, u16 reg_addr, + u32 len, u8 *rval) +{ + u32 cmd_data, cmd_id, val, retry_attempt = 0; + + val = swrm_get_packed_reg_val(&swrm->rcmd_id, len, dev_addr, reg_addr); + + /* wait for FIFO RD to complete to avoid overflow */ + usleep_range(100, 105); + swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val); + /* wait for FIFO RD CMD complete to avoid overflow */ + usleep_range(250, 255); + + do { + swrm->reg_read(swrm, SWRM_CMD_FIFO_RD_FIFO_ADDR, &cmd_data); + rval[0] = cmd_data & 0xFF; + cmd_id = FIELD_GET(SWRM_RD_FIFO_CMD_ID_MASK, cmd_data); + + if (cmd_id != swrm->rcmd_id) { + if (retry_attempt < (MAX_FIFO_RD_RETRY - 1)) { + /* wait 500 us before retry on fifo read failure */ + usleep_range(500, 505); + swrm->reg_write(swrm, SWRM_CMD_FIFO_CMD, + SWRM_CMD_FIFO_FLUSH); + swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val); + } + retry_attempt++; + } else { + return SDW_CMD_OK; + } -err: - spin_lock_irqsave(&ctrl->comp_lock, flags); - ctrl->comp = NULL; - spin_unlock_irqrestore(&ctrl->comp_lock, flags); + } while (retry_attempt < MAX_FIFO_RD_RETRY); - return ret; + dev_err(swrm->dev, "failed to read fifo: reg: 0x%x, rcmd_id: 0x%x,\ + dev_num: 0x%x, cmd_data: 0x%x\n", + reg_addr, swrm->rcmd_id, dev_addr, cmd_data); + + return SDW_CMD_IGNORED; } static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl) @@ -291,7 +324,6 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) { struct qcom_swrm_ctrl *ctrl = dev_id; u32 sts, value; - unsigned long flags; ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS, &sts); @@ -304,8 +336,10 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) } if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) || - sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) - schedule_work(&ctrl->slave_work); + sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) { + qcom_swrm_get_device_status(ctrl); + sdw_handle_slave_status(&ctrl->bus, ctrl->status); + } /** * clear the interrupt before complete() is called, as complete can @@ -314,15 +348,12 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id) */ ctrl->reg_write(ctrl, SWRM_INTERRUPT_CLEAR, sts); - if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED) { - spin_lock_irqsave(&ctrl->comp_lock, flags); - if (ctrl->comp) - complete(ctrl->comp); - spin_unlock_irqrestore(&ctrl->comp_lock, flags); - } + if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED) + complete(&ctrl->broadcast); return IRQ_HANDLED; } + static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl) { u32 val; @@ -570,16 +601,6 @@ static u32 qcom_swrm_freq_tbl[MAX_FREQ_NUM] = { DEFAULT_CLK_FREQ, }; -static void qcom_swrm_slave_wq(struct work_struct *work) -{ - struct qcom_swrm_ctrl *ctrl = - container_of(work, struct qcom_swrm_ctrl, slave_work); - - qcom_swrm_get_device_status(ctrl); - sdw_handle_slave_status(&ctrl->bus, ctrl->status); -} - - static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl, struct sdw_stream_runtime *stream) { @@ -947,9 +968,8 @@ static int qcom_swrm_probe(struct platform_device *pdev) ctrl->dev = dev; dev_set_drvdata(&pdev->dev, ctrl); - spin_lock_init(&ctrl->comp_lock); mutex_init(&ctrl->port_lock); - INIT_WORK(&ctrl->slave_work, qcom_swrm_slave_wq); + init_completion(&ctrl->broadcast); ctrl->bus.ops = &qcom_swrm_ops; ctrl->bus.port_ops = &qcom_swrm_port_ops; -- 2.21.0
next prev parent reply other threads:[~2021-03-12 12:01 UTC|newest] Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-03-12 12:00 [PATCH v4 0/9] soundwire: qcom: various improvements Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 1/9] dt-bindings: soundwire: qcom: clarify data port bus parameters Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-23 22:47 ` Rob Herring 2021-03-23 22:47 ` Rob Herring 2021-03-12 12:00 ` [PATCH v4 2/9] soundwire: qcom: add support to missing transport params Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 3/9] soundwire: qcom: set continue execution flag for ignored commands Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 4/9] soundwire: qcom: start the clock during initialization Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla [this message] 2021-03-12 12:00 ` [PATCH v4 5/9] soundwire: qcom: update register read/write routine Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 6/9] soundwire: qcom: add support to new interrupts Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 7/9] soundwire: export sdw_compare_devid() and sdw_extract_slave_id() Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 12:00 ` [PATCH v4 8/9] soundwire: qcom: add auto enumeration support Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-20 6:13 ` kernel test robot 2021-03-20 6:13 ` kernel test robot 2021-03-20 6:13 ` kernel test robot 2021-03-12 12:00 ` [PATCH v4 9/9] soundwire: qcom: wait for enumeration to be complete in probe Srinivas Kandagatla 2021-03-12 12:00 ` Srinivas Kandagatla 2021-03-12 16:33 ` [PATCH v4 0/9] soundwire: qcom: various improvements Pierre-Louis Bossart
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210312120009.22386-6-srinivas.kandagatla@linaro.org \ --to=srinivas.kandagatla@linaro.org \ --cc=alsa-devel@alsa-project.org \ --cc=devicetree@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=pierre-louis.bossart@linux.intel.com \ --cc=robh@kernel.org \ --cc=sanyog.r.kale@intel.com \ --cc=vkoul@kernel.org \ --cc=yung-chuan.liao@linux.intel.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.