[PATCH v4 0/5] soundwire: add static port map support

[PATCH v4 0/5] soundwire: add static port map support

[Srinivas Kandagatla]

In some cases, SoundWire device ports are statically mapped to Controller
ports during design, however there is no way to expose this information
to the controller. Controllers like Qualcomm ones use this info to setup
static bandwidth parameters for those ports.

A generic port allocation is not possible in this cases!
This patch adds a new member m_port_map to SoundWire device so that
it can populate the static master port map and share it with controller
to be able to setup correct bandwidth parameters.

As a user of this feature this patchset also adds new bindings for
wsa881x smart speaker which has 4 ports which are statically mapped
to the 3 output and 1 input port of the controller.

Tested it on DB845c and SM8250 MTP.

thanks,
srini

Changes since v3:
	- updated kernel doc for more clarity on m_port_map

Srinivas Kandagatla (5):
  soundwire: add static port mapping support
  soundwire: qcom: update port map allocation bit mask
  soundwire: qcom: add static port map support
  ASoC: dt-bindings: wsa881x: add bindings for port mapping
  ASoC: codecs: wsa881x: add static port map support

 .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
 drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
 include/linux/soundwire/sdw.h                 |  2 ++
 sound/soc/codecs/wsa881x.c                    |  7 +++++
 4 files changed, 43 insertions(+), 6 deletions(-)

-- 
2.21.0

[PATCH v4 0/5] soundwire: add static port map support

[Srinivas Kandagatla]

In some cases, SoundWire device ports are statically mapped to Controller
ports during design, however there is no way to expose this information
to the controller. Controllers like Qualcomm ones use this info to setup
static bandwidth parameters for those ports.

A generic port allocation is not possible in this cases!
This patch adds a new member m_port_map to SoundWire device so that
it can populate the static master port map and share it with controller
to be able to setup correct bandwidth parameters.

As a user of this feature this patchset also adds new bindings for
wsa881x smart speaker which has 4 ports which are statically mapped
to the 3 output and 1 input port of the controller.

Tested it on DB845c and SM8250 MTP.

thanks,
srini

Changes since v3:
	- updated kernel doc for more clarity on m_port_map

Srinivas Kandagatla (5):
  soundwire: add static port mapping support
  soundwire: qcom: update port map allocation bit mask
  soundwire: qcom: add static port map support
  ASoC: dt-bindings: wsa881x: add bindings for port mapping
  ASoC: codecs: wsa881x: add static port map support

 .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
 drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
 include/linux/soundwire/sdw.h                 |  2 ++
 sound/soc/codecs/wsa881x.c                    |  7 +++++
 4 files changed, 43 insertions(+), 6 deletions(-)

-- 
2.21.0

[PATCH v4 1/5] soundwire: add static port mapping support

[Srinivas Kandagatla]

Some of the SoundWire device ports are statically mapped to Controller
ports during design, however there is no way to expose this information
to the controller. Controllers like Qualcomm ones use this info to setup
static bandwidth parameters for those ports.

A generic port allocation is not possible in this cases!
So this patch adds a new member m_port_map to struct sdw_slave to expose
this static map.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 include/linux/soundwire/sdw.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/linux/soundwire/sdw.h b/include/linux/soundwire/sdw.h
index d08039d65825..2f52d6609076 100644
--- a/include/linux/soundwire/sdw.h
+++ b/include/linux/soundwire/sdw.h
@@ -614,6 +614,7 @@ struct sdw_slave_ops {
  * @debugfs: Slave debugfs
  * @node: node for bus list
  * @port_ready: Port ready completion flag for each Slave port
+ * @m_port_map: static Master port map for each Slave port
  * @dev_num: Current Device Number, values can be 0 or dev_num_sticky
  * @dev_num_sticky: one-time static Device Number assigned by Bus
  * @probed: boolean tracking driver state
@@ -645,6 +646,7 @@ struct sdw_slave {
 #endif
 	struct list_head node;
 	struct completion port_ready[SDW_MAX_PORTS];
+	unsigned int m_port_map[SDW_MAX_PORTS];
 	enum sdw_clk_stop_mode curr_clk_stop_mode;
 	u16 dev_num;
 	u16 dev_num_sticky;
-- 
2.21.0

[PATCH v4 1/5] soundwire: add static port mapping support

[Srinivas Kandagatla]

Some of the SoundWire device ports are statically mapped to Controller
ports during design, however there is no way to expose this information
to the controller. Controllers like Qualcomm ones use this info to setup
static bandwidth parameters for those ports.

A generic port allocation is not possible in this cases!
So this patch adds a new member m_port_map to struct sdw_slave to expose
this static map.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 include/linux/soundwire/sdw.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/linux/soundwire/sdw.h b/include/linux/soundwire/sdw.h
index d08039d65825..2f52d6609076 100644
--- a/include/linux/soundwire/sdw.h
+++ b/include/linux/soundwire/sdw.h
@@ -614,6 +614,7 @@ struct sdw_slave_ops {
  * @debugfs: Slave debugfs
  * @node: node for bus list
  * @port_ready: Port ready completion flag for each Slave port
+ * @m_port_map: static Master port map for each Slave port
  * @dev_num: Current Device Number, values can be 0 or dev_num_sticky
  * @dev_num_sticky: one-time static Device Number assigned by Bus
  * @probed: boolean tracking driver state
@@ -645,6 +646,7 @@ struct sdw_slave {
 #endif
 	struct list_head node;
 	struct completion port_ready[SDW_MAX_PORTS];
+	unsigned int m_port_map[SDW_MAX_PORTS];
 	enum sdw_clk_stop_mode curr_clk_stop_mode;
 	u16 dev_num;
 	u16 dev_num_sticky;
-- 
2.21.0

[PATCH v4 2/5] soundwire: qcom: update port map allocation bit mask

[Srinivas Kandagatla]

currently the internal bitmask used for allocating ports starts with offset 0.
This is bit confusing as data port numbers on Qualcomm controller are valid
from 1 to 14. So adjust this bit mask accordingly, this will also help while
adding static port map support.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 6d22df01f354..9e70c53e2c7b 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -519,7 +519,7 @@ static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl,
 			port_mask = &ctrl->din_port_mask;
 
 		list_for_each_entry(p_rt, &m_rt->port_list, port_node)
-			clear_bit(p_rt->num - 1, port_mask);
+			clear_bit(p_rt->num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -552,13 +552,13 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
 				/* Port numbers start from 1 - 14*/
 				pn = find_first_zero_bit(port_mask, maxport);
-				if (pn > (maxport - 1)) {
+				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
 					goto err;
 				}
 				set_bit(pn, port_mask);
-				pconfig[nports].num = pn + 1;
+				pconfig[nports].num = pn;
 				pconfig[nports].ch_mask = p_rt->ch_mask;
 				nports++;
 			}
@@ -580,7 +580,7 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 err:
 	if (ret) {
 		for (i = 0; i < nports; i++)
-			clear_bit(pconfig[i].num - 1, port_mask);
+			clear_bit(pconfig[i].num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -754,6 +754,9 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
 	ctrl->num_dout_ports = val;
 
 	nports = ctrl->num_dout_ports + ctrl->num_din_ports;
+	/* Valid port numbers are from 1-14, so mask out port 0 explicitly */
+	set_bit(0, &ctrl->dout_port_mask);
+	set_bit(0, &ctrl->din_port_mask);
 
 	ret = of_property_read_u8_array(np, "qcom,ports-offset1",
 					off1, nports);
-- 
2.21.0

[PATCH v4 2/5] soundwire: qcom: update port map allocation bit mask

[Srinivas Kandagatla]

currently the internal bitmask used for allocating ports starts with offset 0.
This is bit confusing as data port numbers on Qualcomm controller are valid
from 1 to 14. So adjust this bit mask accordingly, this will also help while
adding static port map support.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 6d22df01f354..9e70c53e2c7b 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -519,7 +519,7 @@ static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl,
 			port_mask = &ctrl->din_port_mask;
 
 		list_for_each_entry(p_rt, &m_rt->port_list, port_node)
-			clear_bit(p_rt->num - 1, port_mask);
+			clear_bit(p_rt->num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -552,13 +552,13 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
 				/* Port numbers start from 1 - 14*/
 				pn = find_first_zero_bit(port_mask, maxport);
-				if (pn > (maxport - 1)) {
+				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
 					goto err;
 				}
 				set_bit(pn, port_mask);
-				pconfig[nports].num = pn + 1;
+				pconfig[nports].num = pn;
 				pconfig[nports].ch_mask = p_rt->ch_mask;
 				nports++;
 			}
@@ -580,7 +580,7 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 err:
 	if (ret) {
 		for (i = 0; i < nports; i++)
-			clear_bit(pconfig[i].num - 1, port_mask);
+			clear_bit(pconfig[i].num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -754,6 +754,9 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
 	ctrl->num_dout_ports = val;
 
 	nports = ctrl->num_dout_ports + ctrl->num_din_ports;
+	/* Valid port numbers are from 1-14, so mask out port 0 explicitly */
+	set_bit(0, &ctrl->dout_port_mask);
+	set_bit(0, &ctrl->din_port_mask);
 
 	ret = of_property_read_u8_array(np, "qcom,ports-offset1",
 					off1, nports);
-- 
2.21.0

[PATCH v4 3/5] soundwire: qcom: add static port map support

[Srinivas Kandagatla]

SoundWire device ports are statically mapped to Controller ports during
design. Add support to read these from SoundWire devices.
This controller uses static port map info to setup bandwidth
parameters for those ports.

A generic port allocation is not possible in this cases!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 9e70c53e2c7b..39222b04a2e0 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -460,6 +460,8 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
 	struct qcom_swrm_port_config *pcfg;
+	struct sdw_slave *slave;
+	unsigned int m_port;
 	int i = 0;
 
 	list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) {
@@ -473,8 +475,14 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
-				pcfg = &ctrl->pconfig[i];
+				m_port = slave->m_port_map[p_rt->num];
+				/* port config starts at offset 0 so -1 from actual port number */
+				if (m_port)
+					pcfg = &ctrl->pconfig[m_port - 1];
+				else
+					pcfg = &ctrl->pconfig[i];
 				p_rt->transport_params.port_num = p_rt->num;
 				p_rt->transport_params.sample_interval =
 					pcfg->si + 1;
@@ -535,8 +543,10 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 	struct sdw_master_runtime *m_rt;
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
+	struct sdw_slave *slave;
 	unsigned long *port_mask;
 	int i, maxport, pn, nports = 0, ret = 0;
+	unsigned int m_port;
 
 	mutex_lock(&ctrl->port_lock);
 	list_for_each_entry(m_rt, &stream->master_list, stream_node) {
@@ -549,9 +559,15 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
+				m_port = slave->m_port_map[p_rt->num];
 				/* Port numbers start from 1 - 14*/
-				pn = find_first_zero_bit(port_mask, maxport);
+				if (m_port)
+					pn = m_port;
+				else
+					pn = find_first_zero_bit(port_mask, maxport);
+
 				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
-- 
2.21.0

[PATCH v4 3/5] soundwire: qcom: add static port map support

[Srinivas Kandagatla]

SoundWire device ports are statically mapped to Controller ports during
design. Add support to read these from SoundWire devices.
This controller uses static port map info to setup bandwidth
parameters for those ports.

A generic port allocation is not possible in this cases!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 9e70c53e2c7b..39222b04a2e0 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -460,6 +460,8 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
 	struct qcom_swrm_port_config *pcfg;
+	struct sdw_slave *slave;
+	unsigned int m_port;
 	int i = 0;
 
 	list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) {
@@ -473,8 +475,14 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
-				pcfg = &ctrl->pconfig[i];
+				m_port = slave->m_port_map[p_rt->num];
+				/* port config starts at offset 0 so -1 from actual port number */
+				if (m_port)
+					pcfg = &ctrl->pconfig[m_port - 1];
+				else
+					pcfg = &ctrl->pconfig[i];
 				p_rt->transport_params.port_num = p_rt->num;
 				p_rt->transport_params.sample_interval =
 					pcfg->si + 1;
@@ -535,8 +543,10 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 	struct sdw_master_runtime *m_rt;
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
+	struct sdw_slave *slave;
 	unsigned long *port_mask;
 	int i, maxport, pn, nports = 0, ret = 0;
+	unsigned int m_port;
 
 	mutex_lock(&ctrl->port_lock);
 	list_for_each_entry(m_rt, &stream->master_list, stream_node) {
@@ -549,9 +559,15 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
+				m_port = slave->m_port_map[p_rt->num];
 				/* Port numbers start from 1 - 14*/
-				pn = find_first_zero_bit(port_mask, maxport);
+				if (m_port)
+					pn = m_port;
+				else
+					pn = find_first_zero_bit(port_mask, maxport);
+
 				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
-- 
2.21.0

[PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Srinivas Kandagatla]

WSA881x SoundWire device ports are statically assigned to master ports
at design time. So add bindings required to specify these mappings!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 .../devicetree/bindings/sound/qcom,wsa881x.yaml          | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
index ea44d03e58ca..491ce1270cb5 100644
--- a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
@@ -26,6 +26,13 @@ properties:
     description: GPIO spec for Powerdown/Shutdown line to use
     maxItems: 1
 
+  qcom,port-mapping:
+    description: |
+      Specifies static port mapping between slave and master ports.
+      In the order of slave port index.
+    maxItems: 4
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+
   '#thermal-sensor-cells':
     const: 0
 
@@ -54,6 +61,7 @@ examples:
             powerdown-gpios = <&wcdpinctrl 2 0>;
             #thermal-sensor-cells = <0>;
             #sound-dai-cells = <0>;
+            qcom,port-mapping = <1 2 3 7>;
         };
 
         speaker@0,2 {
@@ -62,6 +70,7 @@ examples:
             powerdown-gpios = <&wcdpinctrl 2 0>;
             #thermal-sensor-cells = <0>;
             #sound-dai-cells = <0>;
+            qcom,port-mapping = <4 5 6 8>;
         };
     };
 
-- 
2.21.0

[PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Srinivas Kandagatla]

WSA881x SoundWire device ports are statically assigned to master ports
at design time. So add bindings required to specify these mappings!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 .../devicetree/bindings/sound/qcom,wsa881x.yaml          | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
index ea44d03e58ca..491ce1270cb5 100644
--- a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml
@@ -26,6 +26,13 @@ properties:
     description: GPIO spec for Powerdown/Shutdown line to use
     maxItems: 1
 
+  qcom,port-mapping:
+    description: |
+      Specifies static port mapping between slave and master ports.
+      In the order of slave port index.
+    maxItems: 4
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+
   '#thermal-sensor-cells':
     const: 0
 
@@ -54,6 +61,7 @@ examples:
             powerdown-gpios = <&wcdpinctrl 2 0>;
             #thermal-sensor-cells = <0>;
             #sound-dai-cells = <0>;
+            qcom,port-mapping = <1 2 3 7>;
         };
 
         speaker@0,2 {
@@ -62,6 +70,7 @@ examples:
             powerdown-gpios = <&wcdpinctrl 2 0>;
             #thermal-sensor-cells = <0>;
             #sound-dai-cells = <0>;
+            qcom,port-mapping = <4 5 6 8>;
         };
     };
 
-- 
2.21.0

Re: [PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Rob Herring]

On Mon, 15 Mar 2021 16:56:49 +0000, Srinivas Kandagatla wrote:
> WSA881x SoundWire device ports are statically assigned to master ports
> at design time. So add bindings required to specify these mappings!
> 
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
>  .../devicetree/bindings/sound/qcom,wsa881x.yaml          | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Rob Herring]

On Mon, 15 Mar 2021 16:56:49 +0000, Srinivas Kandagatla wrote:
> WSA881x SoundWire device ports are statically assigned to master ports
> at design time. So add bindings required to specify these mappings!
> 
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
>  .../devicetree/bindings/sound/qcom,wsa881x.yaml          | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Vinod Koul]

On 15-03-21, 16:56, Srinivas Kandagatla wrote:
> WSA881x SoundWire device ports are statically assigned to master ports
> at design time. So add bindings required to specify these mappings!

Mark, are you okay for 4, 5 to go thru sdw tree with your ack? The
patches lgtm

-- 
~Vinod

Re: [PATCH v4 4/5] ASoC: dt-bindings: wsa881x: add bindings for port mapping

[Vinod Koul]

On 15-03-21, 16:56, Srinivas Kandagatla wrote:
> WSA881x SoundWire device ports are statically assigned to master ports
> at design time. So add bindings required to specify these mappings!

Mark, are you okay for 4, 5 to go thru sdw tree with your ack? The
patches lgtm

-- 
~Vinod

[PATCH v4 5/5] ASoC: codecs: wsa881x: add static port map support

[Srinivas Kandagatla]

Two instances of WSA881x(Speaker Right, Speaker Left) ports
are statically mapped to master ports. Allow the driver to parse
those mappings from device tree.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 sound/soc/codecs/wsa881x.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/sound/soc/codecs/wsa881x.c b/sound/soc/codecs/wsa881x.c
index db87e07b11c9..b3568aec0cd0 100644
--- a/sound/soc/codecs/wsa881x.c
+++ b/sound/soc/codecs/wsa881x.c
@@ -1093,6 +1093,7 @@ static int wsa881x_probe(struct sdw_slave *pdev,
 			 const struct sdw_device_id *id)
 {
 	struct wsa881x_priv *wsa881x;
+	struct device *dev = &pdev->dev;
 
 	wsa881x = devm_kzalloc(&pdev->dev, sizeof(*wsa881x), GFP_KERNEL);
 	if (!wsa881x)
@@ -1105,6 +1106,12 @@ static int wsa881x_probe(struct sdw_slave *pdev,
 		return PTR_ERR(wsa881x->sd_n);
 	}
 
+	/* valid port numbers on this codec starts from 1, so skip 0th index */
+	if (of_property_read_u32_array(dev->of_node, "qcom,port-mapping",
+				       &pdev->m_port_map[1],
+				       WSA881X_MAX_SWR_PORTS))
+		dev_info(dev, "Static Port mapping not specified\n");
+
 	dev_set_drvdata(&pdev->dev, wsa881x);
 	wsa881x->slave = pdev;
 	wsa881x->dev = &pdev->dev;
-- 
2.21.0

[PATCH v4 5/5] ASoC: codecs: wsa881x: add static port map support

[Srinivas Kandagatla]

Two instances of WSA881x(Speaker Right, Speaker Left) ports
are statically mapped to master ports. Allow the driver to parse
those mappings from device tree.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 sound/soc/codecs/wsa881x.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/sound/soc/codecs/wsa881x.c b/sound/soc/codecs/wsa881x.c
index db87e07b11c9..b3568aec0cd0 100644
--- a/sound/soc/codecs/wsa881x.c
+++ b/sound/soc/codecs/wsa881x.c
@@ -1093,6 +1093,7 @@ static int wsa881x_probe(struct sdw_slave *pdev,
 			 const struct sdw_device_id *id)
 {
 	struct wsa881x_priv *wsa881x;
+	struct device *dev = &pdev->dev;
 
 	wsa881x = devm_kzalloc(&pdev->dev, sizeof(*wsa881x), GFP_KERNEL);
 	if (!wsa881x)
@@ -1105,6 +1106,12 @@ static int wsa881x_probe(struct sdw_slave *pdev,
 		return PTR_ERR(wsa881x->sd_n);
 	}
 
+	/* valid port numbers on this codec starts from 1, so skip 0th index */
+	if (of_property_read_u32_array(dev->of_node, "qcom,port-mapping",
+				       &pdev->m_port_map[1],
+				       WSA881X_MAX_SWR_PORTS))
+		dev_info(dev, "Static Port mapping not specified\n");
+
 	dev_set_drvdata(&pdev->dev, wsa881x);
 	wsa881x->slave = pdev;
 	wsa881x->dev = &pdev->dev;
-- 
2.21.0

Re: [PATCH v4 0/5] soundwire: add static port map support

[Pierre-Louis Bossart]

On 3/15/21 11:56 AM, Srinivas Kandagatla wrote:
> In some cases, SoundWire device ports are statically mapped to Controller
> ports during design, however there is no way to expose this information
> to the controller. Controllers like Qualcomm ones use this info to setup
> static bandwidth parameters for those ports.
> 
> A generic port allocation is not possible in this cases!
> This patch adds a new member m_port_map to SoundWire device so that
> it can populate the static master port map and share it with controller
> to be able to setup correct bandwidth parameters.
> 
> As a user of this feature this patchset also adds new bindings for
> wsa881x smart speaker which has 4 ports which are statically mapped
> to the 3 output and 1 input port of the controller.
> 
> Tested it on DB845c and SM8250 MTP.
> 
> thanks,
> srini

Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>

> Changes since v3:
> 	- updated kernel doc for more clarity on m_port_map
> 
> Srinivas Kandagatla (5):
>    soundwire: add static port mapping support
>    soundwire: qcom: update port map allocation bit mask
>    soundwire: qcom: add static port map support
>    ASoC: dt-bindings: wsa881x: add bindings for port mapping
>    ASoC: codecs: wsa881x: add static port map support
> 
>   .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
>   drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
>   include/linux/soundwire/sdw.h                 |  2 ++
>   sound/soc/codecs/wsa881x.c                    |  7 +++++
>   4 files changed, 43 insertions(+), 6 deletions(-)
> 

Re: [PATCH v4 0/5] soundwire: add static port map support

[Pierre-Louis Bossart]

On 3/15/21 11:56 AM, Srinivas Kandagatla wrote:
> In some cases, SoundWire device ports are statically mapped to Controller
> ports during design, however there is no way to expose this information
> to the controller. Controllers like Qualcomm ones use this info to setup
> static bandwidth parameters for those ports.
> 
> A generic port allocation is not possible in this cases!
> This patch adds a new member m_port_map to SoundWire device so that
> it can populate the static master port map and share it with controller
> to be able to setup correct bandwidth parameters.
> 
> As a user of this feature this patchset also adds new bindings for
> wsa881x smart speaker which has 4 ports which are statically mapped
> to the 3 output and 1 input port of the controller.
> 
> Tested it on DB845c and SM8250 MTP.
> 
> thanks,
> srini

Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>

> Changes since v3:
> 	- updated kernel doc for more clarity on m_port_map
> 
> Srinivas Kandagatla (5):
>    soundwire: add static port mapping support
>    soundwire: qcom: update port map allocation bit mask
>    soundwire: qcom: add static port map support
>    ASoC: dt-bindings: wsa881x: add bindings for port mapping
>    ASoC: codecs: wsa881x: add static port map support
> 
>   .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
>   drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
>   include/linux/soundwire/sdw.h                 |  2 ++
>   sound/soc/codecs/wsa881x.c                    |  7 +++++
>   4 files changed, 43 insertions(+), 6 deletions(-)
> 

Re: [PATCH v4 0/5] soundwire: add static port map support

[Vinod Koul]

On 15-03-21, 16:56, Srinivas Kandagatla wrote:
> In some cases, SoundWire device ports are statically mapped to Controller
> ports during design, however there is no way to expose this information
> to the controller. Controllers like Qualcomm ones use this info to setup
> static bandwidth parameters for those ports.
> 
> A generic port allocation is not possible in this cases!
> This patch adds a new member m_port_map to SoundWire device so that
> it can populate the static master port map and share it with controller
> to be able to setup correct bandwidth parameters.
> 
> As a user of this feature this patchset also adds new bindings for
> wsa881x smart speaker which has 4 ports which are statically mapped
> to the 3 output and 1 input port of the controller.
> 
> Tested it on DB845c and SM8250 MTP.
> 
> thanks,
> srini
> 
> Changes since v3:
> 	- updated kernel doc for more clarity on m_port_map
> 
> Srinivas Kandagatla (5):
>   soundwire: add static port mapping support
>   soundwire: qcom: update port map allocation bit mask
>   soundwire: qcom: add static port map support

Applied all sdw patches, thanks

>   ASoC: dt-bindings: wsa881x: add bindings for port mapping
>   ASoC: codecs: wsa881x: add static port map support
> 
>  .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
>  drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
>  include/linux/soundwire/sdw.h                 |  2 ++
>  sound/soc/codecs/wsa881x.c                    |  7 +++++
>  4 files changed, 43 insertions(+), 6 deletions(-)
> 
> -- 
> 2.21.0

-- 
~Vinod

Re: [PATCH v4 0/5] soundwire: add static port map support

[Vinod Koul]

On 15-03-21, 16:56, Srinivas Kandagatla wrote:
> In some cases, SoundWire device ports are statically mapped to Controller
> ports during design, however there is no way to expose this information
> to the controller. Controllers like Qualcomm ones use this info to setup
> static bandwidth parameters for those ports.
> 
> A generic port allocation is not possible in this cases!
> This patch adds a new member m_port_map to SoundWire device so that
> it can populate the static master port map and share it with controller
> to be able to setup correct bandwidth parameters.
> 
> As a user of this feature this patchset also adds new bindings for
> wsa881x smart speaker which has 4 ports which are statically mapped
> to the 3 output and 1 input port of the controller.
> 
> Tested it on DB845c and SM8250 MTP.
> 
> thanks,
> srini
> 
> Changes since v3:
> 	- updated kernel doc for more clarity on m_port_map
> 
> Srinivas Kandagatla (5):
>   soundwire: add static port mapping support
>   soundwire: qcom: update port map allocation bit mask
>   soundwire: qcom: add static port map support

Applied all sdw patches, thanks

>   ASoC: dt-bindings: wsa881x: add bindings for port mapping
>   ASoC: codecs: wsa881x: add static port map support
> 
>  .../bindings/sound/qcom,wsa881x.yaml          |  9 ++++++
>  drivers/soundwire/qcom.c                      | 31 +++++++++++++++----
>  include/linux/soundwire/sdw.h                 |  2 ++
>  sound/soc/codecs/wsa881x.c                    |  7 +++++
>  4 files changed, 43 insertions(+), 6 deletions(-)
> 
> -- 
> 2.21.0

-- 
~Vinod