[PATCH v2 0/4] Add peripheral support to imx8mq-nitrogen board

[PATCH v2 0/4] Add peripheral support to imx8mq-nitrogen board

[Adrien Grassein]

Hi,

this patch set aims is to add support of multiple peripheral of the
Boundary8M board:
  - USB Host;
  - USB device;
  - DB_DSIHD sub board for MIPI-DSI to HDMI output (via lt8912b chip).


Updates in v2:
  - Use a GPIO hog to handle the USB HOST reset line;
  - Remove useless GPIO hog for lt8912b.


Thanks,

Adrien Grassein (4):
  arm64: dts: imx8mq-nitrogen: add USB OTG support
  arm64: dts: imx8mq-nitrogen: add USB HOST support
  arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI
  arm64: defconfig: Enable LT8912B DRM bridge driver

 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 185 ++++++++++++++++++
 arch/arm64/configs/defconfig                  |   1 +
 2 files changed, 186 insertions(+)

-- 
2.25.1

[PATCH v2 0/4] Add peripheral support to imx8mq-nitrogen board

[Adrien Grassein]

Hi,

this patch set aims is to add support of multiple peripheral of the
Boundary8M board:
  - USB Host;
  - USB device;
  - DB_DSIHD sub board for MIPI-DSI to HDMI output (via lt8912b chip).


Updates in v2:
  - Use a GPIO hog to handle the USB HOST reset line;
  - Remove useless GPIO hog for lt8912b.


Thanks,

Adrien Grassein (4):
  arm64: dts: imx8mq-nitrogen: add USB OTG support
  arm64: dts: imx8mq-nitrogen: add USB HOST support
  arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI
  arm64: defconfig: Enable LT8912B DRM bridge driver

 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 185 ++++++++++++++++++
 arch/arm64/configs/defconfig                  |   1 +
 2 files changed, 186 insertions(+)

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/4] arm64: dts: imx8mq-nitrogen: add USB OTG support

[Adrien Grassein]

Add the description for the USB OTG port.
The OTG port uses a dedicated regulator for vbus.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 35 +++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index 81d269296610..b46f45a82be1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -34,6 +34,17 @@ power {
 		};
 	};
 
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_vref_0v9: regulator-vref-0v9 {
 		compatible = "regulator-fixed";
 		regulator-name = "vref-0v9";
@@ -190,6 +201,18 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_dwc3_0 {
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb3_0>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
 &usdhc1 {
 	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
 	assigned-clock-rates = <400000000>;
@@ -339,6 +362,12 @@ MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20		0x16
 		>;
 	};
 
+	pinctrl_reg_usbotg_vbus: reg-usbotg-vbusgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x16
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x45
@@ -353,6 +382,12 @@ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
 		>;
 	};
 
+	pinctrl_usb3_0: usb3-0grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x16
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
-- 
2.25.1

[PATCH v2 1/4] arm64: dts: imx8mq-nitrogen: add USB OTG support

[Adrien Grassein]

Add the description for the USB OTG port.
The OTG port uses a dedicated regulator for vbus.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 35 +++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index 81d269296610..b46f45a82be1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -34,6 +34,17 @@ power {
 		};
 	};
 
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_vref_0v9: regulator-vref-0v9 {
 		compatible = "regulator-fixed";
 		regulator-name = "vref-0v9";
@@ -190,6 +201,18 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_dwc3_0 {
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb3_0>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
 &usdhc1 {
 	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
 	assigned-clock-rates = <400000000>;
@@ -339,6 +362,12 @@ MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20		0x16
 		>;
 	};
 
+	pinctrl_reg_usbotg_vbus: reg-usbotg-vbusgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x16
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x45
@@ -353,6 +382,12 @@ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
 		>;
 	};
 
+	pinctrl_usb3_0: usb3-0grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x16
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/4] arm64: dts: imx8mq-nitrogen: add USB HOST support

[Adrien Grassein]

Add the description for the USB host port.
This port is linked to a resettable USB HUB so handle
this reset signal with a GPIO hog.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index b46f45a82be1..04992cbba56e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -102,6 +102,14 @@ ethphy0: ethernet-phy@4 {
 	};
 };
 
+&gpio1 {
+	usb-host-reset-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -213,6 +221,22 @@ &usb3_phy0 {
 	status = "okay";
 };
 
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/*
+ * On this board, USB host is connected to a resettable hub.
+ * The reset signal is connected to the GPIO <&gpio1 14 GPIO_ACTIVE_LOW>.
+ * You need to activate it in the bootloader or in the userspace.
+ */
+&usb3_phy1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb3_1>;
+};
+
 &usdhc1 {
 	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
 	assigned-clock-rates = <400000000>;
@@ -388,6 +412,12 @@ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x16
 		>;
 	};
 
+	pinctrl_usb3_1: usb3-1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x16
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
-- 
2.25.1

[PATCH v2 2/4] arm64: dts: imx8mq-nitrogen: add USB HOST support

[Adrien Grassein]

Add the description for the USB host port.
This port is linked to a resettable USB HUB so handle
this reset signal with a GPIO hog.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index b46f45a82be1..04992cbba56e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -102,6 +102,14 @@ ethphy0: ethernet-phy@4 {
 	};
 };
 
+&gpio1 {
+	usb-host-reset-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -213,6 +221,22 @@ &usb3_phy0 {
 	status = "okay";
 };
 
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/*
+ * On this board, USB host is connected to a resettable hub.
+ * The reset signal is connected to the GPIO <&gpio1 14 GPIO_ACTIVE_LOW>.
+ * You need to activate it in the bootloader or in the userspace.
+ */
+&usb3_phy1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb3_1>;
+};
+
 &usdhc1 {
 	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
 	assigned-clock-rates = <400000000>;
@@ -388,6 +412,12 @@ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x16
 		>;
 	};
 
+	pinctrl_usb3_1: usb3-1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x16
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/4] arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI

[Adrien Grassein]

Add support of the lt8912b in the DTB.
This adds the support of the DB_DSIHD daugther board from
Boundary Devices.


Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 128 ++++++++++++++++++
 1 file changed, 128 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index 04992cbba56e..da5a95ffa8b4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -34,6 +34,19 @@ power {
 		};
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		ddc-i2c-bus = <&ddc_i2c_bus>;
+		label = "hdmi";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&lt8912_out>;
+			};
+		};
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -81,6 +94,9 @@ reg_vref_5v: regulator-vref-5v {
 	};
 };
 
+&dphy {
+	status = "okay";
+};
 
 &fec1 {
 	pinctrl-names = "default";
@@ -193,6 +209,105 @@ rtc@68 {
 	};
 };
 
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	pca9546: i2cmux9546@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c4@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+
+			hdmi-bridge@48 {
+				compatible = "lontium,lt8912b";
+				reg = <0x48> ;
+				reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						hdmi_out_in: endpoint {
+							data-lanes = <1 2 3 4>;
+							remote-endpoint = <&mipi_dsi_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						lt8912_out: endpoint {
+							remote-endpoint = <&hdmi_connector_in>;
+						};
+					};
+				};
+			};
+		};
+
+		ddc_i2c_bus: i2c4@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+		};
+
+		i2c4@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+
+			max7323: max7323@68 {
+				compatible = "maxim,max7323";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_max7323>;
+				gpio-controller;
+				reg = <0x68>;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&gpio3 {
+	max7323_intterupt {
+		gpio-hog;
+		gpios = <15 0>;
+		input;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mipi_dsi_out: endpoint {
+				remote-endpoint = <&hdmi_out_in>;
+			};
+		};
+	};
+};
+
 &uart1 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -368,6 +483,19 @@ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x49
 		>;
 	};
 
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_max7323: max7323grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
+		>;
+	};
+
 	pinctrl_reg_arm_dram: reg-arm-dramgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24	0x16
-- 
2.25.1

[PATCH v2 3/4] arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI

[Adrien Grassein]

Add support of the lt8912b in the DTB.
This adds the support of the DB_DSIHD daugther board from
Boundary Devices.


Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 .../boot/dts/freescale/imx8mq-nitrogen.dts    | 128 ++++++++++++++++++
 1 file changed, 128 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index 04992cbba56e..da5a95ffa8b4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -34,6 +34,19 @@ power {
 		};
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		ddc-i2c-bus = <&ddc_i2c_bus>;
+		label = "hdmi";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&lt8912_out>;
+			};
+		};
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -81,6 +94,9 @@ reg_vref_5v: regulator-vref-5v {
 	};
 };
 
+&dphy {
+	status = "okay";
+};
 
 &fec1 {
 	pinctrl-names = "default";
@@ -193,6 +209,105 @@ rtc@68 {
 	};
 };
 
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	pca9546: i2cmux9546@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c4@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+
+			hdmi-bridge@48 {
+				compatible = "lontium,lt8912b";
+				reg = <0x48> ;
+				reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						hdmi_out_in: endpoint {
+							data-lanes = <1 2 3 4>;
+							remote-endpoint = <&mipi_dsi_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						lt8912_out: endpoint {
+							remote-endpoint = <&hdmi_connector_in>;
+						};
+					};
+				};
+			};
+		};
+
+		ddc_i2c_bus: i2c4@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+		};
+
+		i2c4@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clock-frequency = <100000>;
+
+			max7323: max7323@68 {
+				compatible = "maxim,max7323";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_max7323>;
+				gpio-controller;
+				reg = <0x68>;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&gpio3 {
+	max7323_intterupt {
+		gpio-hog;
+		gpios = <15 0>;
+		input;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mipi_dsi_out: endpoint {
+				remote-endpoint = <&hdmi_out_in>;
+			};
+		};
+	};
+};
+
 &uart1 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -368,6 +483,19 @@ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x49
 		>;
 	};
 
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_max7323: max7323grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
+		>;
+	};
+
 	pinctrl_reg_arm_dram: reg-arm-dramgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24	0x16
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/4] arm64: defconfig: Enable LT8912B DRM bridge driver

[Adrien Grassein]

This driver is used by the Nitrogen8 SBC.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts | 8 --------
 arch/arm64/configs/defconfig                      | 1 +
 2 files changed, 1 insertion(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index da5a95ffa8b4..4ffd23ea705f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -281,14 +281,6 @@ max7323: max7323@68 {
 	};
 };
 
-&gpio3 {
-	max7323_intterupt {
-		gpio-hog;
-		gpios = <15 0>;
-		input;
-	};
-};
-
 &lcdif {
 	status = "okay";
 };
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 3f059bca9e24..39bddac5e44a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -690,6 +690,7 @@ CONFIG_DRM_PANEL_RAYDIUM_RM67191=m
 CONFIG_DRM_PANEL_SITRONIX_ST7703=m
 CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA=m
 CONFIG_DRM_DISPLAY_CONNECTOR=m
+CONFIG_DRM_LONTIUM_LT8912B=m
 CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_LONTIUM_LT9611=m
 CONFIG_DRM_SII902X=m
-- 
2.25.1

[PATCH v2 4/4] arm64: defconfig: Enable LT8912B DRM bridge driver

[Adrien Grassein]

This driver is used by the Nitrogen8 SBC.

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
 arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts | 8 --------
 arch/arm64/configs/defconfig                      | 1 +
 2 files changed, 1 insertion(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index da5a95ffa8b4..4ffd23ea705f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -281,14 +281,6 @@ max7323: max7323@68 {
 	};
 };
 
-&gpio3 {
-	max7323_intterupt {
-		gpio-hog;
-		gpios = <15 0>;
-		input;
-	};
-};
-
 &lcdif {
 	status = "okay";
 };
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 3f059bca9e24..39bddac5e44a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -690,6 +690,7 @@ CONFIG_DRM_PANEL_RAYDIUM_RM67191=m
 CONFIG_DRM_PANEL_SITRONIX_ST7703=m
 CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA=m
 CONFIG_DRM_DISPLAY_CONNECTOR=m
+CONFIG_DRM_LONTIUM_LT8912B=m
 CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_LONTIUM_LT9611=m
 CONFIG_DRM_SII902X=m
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel