From: Oleksij Rempel <o.rempel@pengutronix.de> To: Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Andrew Lunn <andrew@lunn.ch>, Florian Fainelli <f.fainelli@gmail.com>, Heiner Kallweit <hkallweit1@gmail.com>, Fugang Duan <fugang.duan@nxp.com> Cc: Oleksij Rempel <o.rempel@pengutronix.de>, kernel@pengutronix.de, netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-imx@nxp.com, Fabio Estevam <festevam@gmail.com>, David Jander <david@protonic.nl>, Russell King <linux@armlinux.org.uk>, Philippe Schenker <philippe.schenker@toradex.com> Subject: [PATCH net-next v1 2/3] net: phy: at803x: AR8085: add loopback support Date: Tue, 30 Mar 2021 15:54:06 +0200 [thread overview] Message-ID: <20210330135407.17010-3-o.rempel@pengutronix.de> (raw) In-Reply-To: <20210330135407.17010-1-o.rempel@pengutronix.de> PHY loopback is needed for the ethernet controller self test support. This PHY was tested with the FEC sefltest. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/phy/at803x.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index d7799beb811c..8679738cf2ab 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -326,6 +326,30 @@ static int at803x_resume(struct phy_device *phydev) return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0); } +static int at803x_loopback(struct phy_device *phydev, bool enable) +{ + int ret; + + if (enable) + ret = phy_clear_bits(phydev, MII_BMCR, BMCR_ANENABLE); + else + ret = phy_set_bits(phydev, MII_BMCR, BMCR_ANENABLE); + + if (ret) + return ret; + + ret = genphy_loopback(phydev, enable); + + /* + * Loop back needs some time to start transmitting packets in the loop. + * Documentation says nothing about it, so I take time which seems to + * work on AR8085. + */ + msleep(1); + + return ret; +} + static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev, unsigned int selector) { @@ -1128,6 +1152,7 @@ static struct phy_driver at803x_driver[] = { .get_wol = at803x_get_wol, .suspend = at803x_suspend, .resume = at803x_resume, + .set_loopback = at803x_loopback, /* PHY_GBIT_FEATURES */ .read_status = at803x_read_status, .config_intr = at803x_config_intr, -- 2.29.2
WARNING: multiple messages have this Message-ID (diff)
From: Oleksij Rempel <o.rempel@pengutronix.de> To: Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Andrew Lunn <andrew@lunn.ch>, Florian Fainelli <f.fainelli@gmail.com>, Heiner Kallweit <hkallweit1@gmail.com>, Fugang Duan <fugang.duan@nxp.com> Cc: Oleksij Rempel <o.rempel@pengutronix.de>, kernel@pengutronix.de, netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-imx@nxp.com, Fabio Estevam <festevam@gmail.com>, David Jander <david@protonic.nl>, Russell King <linux@armlinux.org.uk>, Philippe Schenker <philippe.schenker@toradex.com> Subject: [PATCH net-next v1 2/3] net: phy: at803x: AR8085: add loopback support Date: Tue, 30 Mar 2021 15:54:06 +0200 [thread overview] Message-ID: <20210330135407.17010-3-o.rempel@pengutronix.de> (raw) In-Reply-To: <20210330135407.17010-1-o.rempel@pengutronix.de> PHY loopback is needed for the ethernet controller self test support. This PHY was tested with the FEC sefltest. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/phy/at803x.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index d7799beb811c..8679738cf2ab 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -326,6 +326,30 @@ static int at803x_resume(struct phy_device *phydev) return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0); } +static int at803x_loopback(struct phy_device *phydev, bool enable) +{ + int ret; + + if (enable) + ret = phy_clear_bits(phydev, MII_BMCR, BMCR_ANENABLE); + else + ret = phy_set_bits(phydev, MII_BMCR, BMCR_ANENABLE); + + if (ret) + return ret; + + ret = genphy_loopback(phydev, enable); + + /* + * Loop back needs some time to start transmitting packets in the loop. + * Documentation says nothing about it, so I take time which seems to + * work on AR8085. + */ + msleep(1); + + return ret; +} + static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev, unsigned int selector) { @@ -1128,6 +1152,7 @@ static struct phy_driver at803x_driver[] = { .get_wol = at803x_get_wol, .suspend = at803x_suspend, .resume = at803x_resume, + .set_loopback = at803x_loopback, /* PHY_GBIT_FEATURES */ .read_status = at803x_read_status, .config_intr = at803x_config_intr, -- 2.29.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-03-30 13:55 UTC|newest] Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-03-30 13:54 [PATCH net-next v1 0/3] provide basic selftest support for the ethernet FEC driver Oleksij Rempel 2021-03-30 13:54 ` Oleksij Rempel 2021-03-30 13:54 ` [PATCH net-next v1 1/3] net: phy: micrel: KSZ8081: add loopback support Oleksij Rempel 2021-03-30 13:54 ` Oleksij Rempel 2021-03-30 14:06 ` Marc Kleine-Budde 2021-03-30 14:06 ` Marc Kleine-Budde 2021-03-30 14:39 ` Andrew Lunn 2021-03-30 14:39 ` Andrew Lunn 2021-03-30 13:54 ` Oleksij Rempel [this message] 2021-03-30 13:54 ` [PATCH net-next v1 2/3] net: phy: at803x: AR8085: " Oleksij Rempel 2021-03-30 14:08 ` Marc Kleine-Budde 2021-03-30 14:08 ` Marc Kleine-Budde 2021-03-30 14:49 ` Andrew Lunn 2021-03-30 14:49 ` Andrew Lunn 2021-03-30 13:54 ` [PATCH net-next v1 3/3] net: fec: add basic selftest support Oleksij Rempel 2021-03-30 13:54 ` Oleksij Rempel 2021-03-31 1:07 ` kernel test robot 2021-03-31 1:07 ` kernel test robot 2021-03-31 1:07 ` kernel test robot 2021-03-31 12:27 ` Andrew Lunn 2021-03-31 12:27 ` Andrew Lunn 2021-04-01 7:47 ` Oleksij Rempel 2021-04-01 7:47 ` Oleksij Rempel 2021-04-01 16:06 ` Florian Fainelli 2021-04-01 16:06 ` Florian Fainelli
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210330135407.17010-3-o.rempel@pengutronix.de \ --to=o.rempel@pengutronix.de \ --cc=andrew@lunn.ch \ --cc=david@protonic.nl \ --cc=f.fainelli@gmail.com \ --cc=festevam@gmail.com \ --cc=fugang.duan@nxp.com \ --cc=hkallweit1@gmail.com \ --cc=kernel@pengutronix.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-imx@nxp.com \ --cc=linux-kernel@vger.kernel.org \ --cc=linux@armlinux.org.uk \ --cc=netdev@vger.kernel.org \ --cc=philippe.schenker@toradex.com \ --cc=s.hauer@pengutronix.de \ --cc=shawnguo@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.