[PATCH hwmon-next 0/3] dd support for MPS Multi-phase mp2888 controller

[PATCH hwmon-next 0/3] dd support for MPS Multi-phase mp2888 controller

[Vadim Pasternak]

Add driver and documentation for mp2888 device from Monolithic Power
Systems, Inc. (MPS) vendor. This is a digital, multi-phase, pulse-width
modulation controller.

Patch set includes:
Patch #1 - increases maximum number of phases.
Patch #2 - provides mp2888 driver and documentation.
Patch #3 - providesy binding documentation.

Vadim Pasternak (3):
  hwmon: (pmbus) Increase maximum number of phases per page
  hwmon: (pmbus) Add support for MPS Multi-phase mp2888 controller
  dt-bindings: Add MP2888 voltage regulator device

 .../devicetree/bindings/trivial-devices.yaml       |   2 +
 Documentation/hwmon/mp2888.rst                     | 111 +++++++++
 drivers/hwmon/pmbus/Kconfig                        |   9 +
 drivers/hwmon/pmbus/Makefile                       |   1 +
 drivers/hwmon/pmbus/mp2888.c                       | 256 +++++++++++++++++++++
 drivers/hwmon/pmbus/pmbus.h                        |   2 +-
 6 files changed, 380 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/hwmon/mp2888.rst
 create mode 100644 drivers/hwmon/pmbus/mp2888.c

-- 
2.11.0

[PATCH hwmon-next 1/3] hwmon: (pmbus) Increase maximum number of phases per page

[Vadim Pasternak]

Increase maximum number of phases from 8 to 10 to support multi-phase
devices allowing up to 10 phases.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
---
 drivers/hwmon/pmbus/pmbus.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/hwmon/pmbus/pmbus.h b/drivers/hwmon/pmbus/pmbus.h
index 4c30ec89f5bf..fd43873011a4 100644
--- a/drivers/hwmon/pmbus/pmbus.h
+++ b/drivers/hwmon/pmbus/pmbus.h
@@ -375,7 +375,7 @@ enum pmbus_sensor_classes {
 };
 
 #define PMBUS_PAGES	32	/* Per PMBus specification */
-#define PMBUS_PHASES	8	/* Maximum number of phases per page */
+#define PMBUS_PHASES	10	/* Maximum number of phases per page */
 
 /* Functionality bit mask */
 #define PMBUS_HAVE_VIN		BIT(0)
-- 
2.11.0

[PATCH hwmon-next 2/3] hwmon: (pmbus) Add support for MPS Multi-phase mp2888 controller

[Vadim Pasternak]

Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.

This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
  setting of different formats on rails 1 and 2. For VID the following
  protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
  10-mV DAC, IMVP9 mode with 5-mV DAC.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
---
 Documentation/hwmon/mp2888.rst | 111 ++++++++++++++++++
 drivers/hwmon/pmbus/Kconfig    |   9 ++
 drivers/hwmon/pmbus/Makefile   |   1 +
 drivers/hwmon/pmbus/mp2888.c   | 256 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 377 insertions(+)
 create mode 100644 Documentation/hwmon/mp2888.rst
 create mode 100644 drivers/hwmon/pmbus/mp2888.c

diff --git a/Documentation/hwmon/mp2888.rst b/Documentation/hwmon/mp2888.rst
new file mode 100644
index 000000000000..7839a010642a
--- /dev/null
+++ b/Documentation/hwmon/mp2888.rst
@@ -0,0 +1,111 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2888
+====================
+
+Supported chips:
+
+  * MPS MP12254
+
+    Prefix: 'mp2888'
+
+Author:
+
+	Vadim Pasternak <vadimp@nvidia.com>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+vendor dual-loop, digital, multi-phase controller MP2888.
+
+This device: supports:
+
+- One power rail.
+- Programmable Multi-Phase up to 10 Phases.
+- PWM-VID Interface
+- One pages 0 for telemetry.
+- Programmable pins for PMBus Address.
+- Built-In EEPROM to Store Custom Configurations.
+
+Device complaint with:
+
+- PMBus rev 1.3 interface.
+
+Device supports direct format for reading output current, output voltage,
+input and output power and temperature.
+Device supports linear format for reading input voltage and input power.
+
+The driver provides the next attributes for the current:
+
+- for current out input and maximum alarm;
+- for phase current: input and label.
+
+The driver exports the following attributes via the 'sysfs' files, where:
+
+- 'n' is number of configured phases (from 1 to 10);
+- index 1 for "iout";
+- indexes 2 ... 1 + n for phases.
+
+**curr1_alarm**
+
+**curr[1-{1+n}]_input**
+
+**curr[1-{1+n}]_label**
+
+The driver provides the next attributes for the voltage:
+
+- for voltage in: input, low and high critical thresholds, low and high
+  critical alarms;
+- for voltage out: input and high alarm;
+
+The driver exports the following attributes via the 'sysfs' files, where
+
+**in1_crit**
+
+**in1_crit_alarm**
+
+**in1_input**
+
+**in1_label**
+
+**in1_min**
+
+**in1_min_alarm**
+
+**in2_alarm**
+
+**in2_input**
+
+**in2_label**
+
+The driver provides the next attributes for the power:
+
+- for power in alarm and input.
+- for power out: cap, cap alarm an input.
+
+The driver exports the following attributes via the 'sysfs' files, where
+- indexes 1 for "pin";
+- indexes 2 for "pout";
+
+**power1_alarm**
+
+**power1_input**
+
+**power1_label**
+
+**power2_cap**
+
+**power2_cap_alarm**
+
+**power2_input**
+
+**power2_label**
+
+The driver provides the next attributes for the temperature:
+
+**temp1_input**
+
+**temp1_max**
+
+**temp1_max_alarm**
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 32d2fc850621..a57571928b31 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -211,6 +211,15 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_MP2888
+	tristate "MPS MP2888"
+	help
+	  If you say yes here you get hardware monitoring support for MPS
+	  MP2888 Digital, Multi-Phase, Pulse-Width Modulation Controller.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called mp2888.
+
 config SENSORS_MP2975
 	tristate "MPS MP2975"
 	help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 6a4ba0fdc1db..a6d7352621ca 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_MP2888)	+= mp2888.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
diff --git a/drivers/hwmon/pmbus/mp2888.c b/drivers/hwmon/pmbus/mp2888.c
new file mode 100644
index 000000000000..3d4b272616c6
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2888.c
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers
+ *
+ * Copyright (C) 2020 Nvidia Technologies Ltd.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+/* Vendor specific registers. */
+#define MP2888_MFR_SYS_CONFIG	0x44
+#define MP2888_MFR_VR_CONFIG1	0xe1
+
+#define MP2888_TOTAL_CURRENT_RESOLUTION	BIT(3)
+#define MP2888_VIN_LIMIT_UNIT		8
+#define MP2888_VIN_UNIT			3125
+#define MP2888_TEMP_UNIT		10
+#define MP2888_MAX_PHASE		10
+
+struct mp2888_data {
+	struct pmbus_driver_info info;
+	int total_curr_resolution;
+};
+
+#define to_mp2888_data(x)  container_of(x, struct mp2888_data, info)
+
+static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	switch (reg) {
+	case PMBUS_VOUT_MODE:
+		/* Enforce VOUT direct format. */
+		return PB_VOUT_MODE_DIRECT;
+	default:
+		return -ENODATA;
+	}
+}
+
+static int
+mp2888_read_word_helper(struct i2c_client *client, int page, int phase, u8 reg, u16 mask)
+{
+	int ret = pmbus_read_word_data(client, page, phase, reg);
+
+	return (ret > 0) ? ret & mask : ret;
+}
+
+static int mp2888_read_word_data(struct i2c_client *client, int page, int phase, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct mp2888_data *data = to_mp2888_data(info);
+	int ret;
+
+	switch (reg) {
+	case PMBUS_OT_WARN_LIMIT:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(7, 0));
+		break;
+	case PMBUS_VIN_OV_FAULT_LIMIT:
+	case PMBUS_VIN_UV_WARN_LIMIT:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(7, 0));
+		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, MP2888_VIN_LIMIT_UNIT);
+		break;
+	case PMBUS_READ_VIN:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(9, 0));
+		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret * MP2888_VIN_UNIT, 100000);
+		break;
+	case PMBUS_READ_VOUT:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
+		break;
+	case PMBUS_READ_TEMPERATURE_1:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
+		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, MP2888_TEMP_UNIT);
+		break;
+	case PMBUS_READ_IOUT:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
+		ret = (ret < 0) ? ret : data->total_curr_resolution ? DIV_ROUND_CLOSEST(ret, 2) :
+		      DIV_ROUND_CLOSEST(ret, 4);
+		/*
+		 * Current phase sensing, providing by the device through the dedicated
+		 * registers 73h - 77h is not accurate, because sampling of current occurrence of
+		 * bit weight has a big deviation. Calculate per-phase current as total current
+		 * divided by number phases.
+		 */
+		if (phase != 0xff)
+			ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, data->info.phases[page]);
+		break;
+	case PMBUS_READ_POUT:
+	case PMBUS_READ_PIN:
+		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
+		ret = (ret < 0) ? ret : data->total_curr_resolution ? ret :
+		      DIV_ROUND_CLOSEST(ret, 2);
+		break;
+	case PMBUS_OT_FAULT_LIMIT:
+	case PMBUS_UT_WARN_LIMIT:
+	case PMBUS_UT_FAULT_LIMIT:
+	case PMBUS_VIN_UV_FAULT_LIMIT:
+	case PMBUS_VOUT_UV_WARN_LIMIT:
+	case PMBUS_VOUT_OV_WARN_LIMIT:
+	case PMBUS_VOUT_UV_FAULT_LIMIT:
+	case PMBUS_VOUT_OV_FAULT_LIMIT:
+	case PMBUS_VIN_OV_WARN_LIMIT:
+	case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
+	case PMBUS_IOUT_OC_WARN_LIMIT:
+	case PMBUS_IOUT_OC_FAULT_LIMIT:
+	case PMBUS_IOUT_UC_FAULT_LIMIT:
+	case PMBUS_POUT_OP_FAULT_LIMIT:
+	case PMBUS_POUT_OP_WARN_LIMIT:
+	case PMBUS_PIN_OP_WARN_LIMIT:
+	case PMBUS_MFR_VIN_MIN:
+	case PMBUS_MFR_VIN_MAX:
+	case PMBUS_MFR_VOUT_MAX:
+	case PMBUS_MFR_IIN_MAX:
+	case PMBUS_MFR_IOUT_MAX:
+	case PMBUS_MFR_PIN_MAX:
+	case PMBUS_MFR_POUT_MAX:
+	case PMBUS_MFR_MAX_TEMP_1:
+		return -ENXIO;
+	default:
+		return -ENODATA;
+	}
+
+	return ret;
+}
+
+static void mp2888_set_phase(struct pmbus_driver_info *info)
+{
+	int i;
+
+	for (i = 0 ; i < info->phases[0]; i++)
+		info->pfunc[i] = PMBUS_HAVE_IOUT;
+}
+
+static int
+mp2888_identify_multiphase(struct i2c_client *client, struct mp2888_data *data,
+			   struct pmbus_driver_info *info)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
+	if (ret < 0)
+		return ret;
+
+	/* Identify multiphase number - could be from 1 to 10. */
+	ret = i2c_smbus_read_word_data(client, MP2888_MFR_VR_CONFIG1);
+	if (ret <= 0)
+		return ret;
+
+	info->phases[0] = ret & GENMASK(3, 0);
+
+	/*
+	 * The device provides a total of 10 PWM pins, and can be configured to different phase
+	 * count applications for rail.
+	 */
+	if (info->phases[0] > MP2888_MAX_PHASE)
+		return -EINVAL;
+
+	mp2888_set_phase(info);
+
+	return 0;
+}
+
+static int mp2888_current_resolution_get(struct i2c_client *client, struct mp2888_data *data)
+{
+	int ret;
+
+	/*
+	 * Obtain resolution selector for total current report and protection.
+	 * 0: original resolution; 1: half resolution (in such case phase current value should
+	 * be doubled.
+	 */
+	ret = i2c_smbus_read_word_data(client, MP2888_MFR_SYS_CONFIG);
+	if (ret < 0)
+		return ret;
+	data->total_curr_resolution = (ret & MP2888_TOTAL_CURRENT_RESOLUTION) >> 3;
+
+	return 0;
+}
+
+static struct pmbus_driver_info mp2888_info = {
+	.pages = 1,
+	.format[PSC_VOLTAGE_IN] = linear,
+	.format[PSC_VOLTAGE_OUT] = direct,
+	.format[PSC_TEMPERATURE] = direct,
+	.format[PSC_CURRENT_IN] = linear,
+	.format[PSC_CURRENT_OUT] = direct,
+	.format[PSC_POWER] = direct,
+	.m[PSC_TEMPERATURE] = 1,
+	.m[PSC_VOLTAGE_OUT] = 1,
+	.R[PSC_VOLTAGE_OUT] = 3,
+	.m[PSC_CURRENT_OUT] = 1,
+	.m[PSC_POWER] = 1,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT |
+		   PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
+		   PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+		   PMBUS_PHASE_VIRTUAL,
+	.read_byte_data = mp2888_read_byte_data,
+	.read_word_data = mp2888_read_word_data,
+};
+
+static int mp2888_probe(struct i2c_client *client)
+{
+	struct pmbus_driver_info *info;
+	struct mp2888_data *data;
+	int ret;
+
+	data = devm_kzalloc(&client->dev, sizeof(struct mp2888_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	memcpy(&data->info, &mp2888_info, sizeof(*info));
+	info = &data->info;
+
+	/* Identify multiphase configuration. */
+	ret = mp2888_identify_multiphase(client, data, info);
+	if (ret)
+		return ret;
+
+	/* Obtain total current resolution. */
+	ret = mp2888_current_resolution_get(client, data);
+	if (ret)
+		return ret;
+
+	return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2888_id[] = {
+	{"mp2888", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2888_id);
+
+static const struct of_device_id __maybe_unused mp2888_of_match[] = {
+	{.compatible = "mps,mp2888"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, mp2888_of_match);
+
+static struct i2c_driver mp2888_driver = {
+	.driver = {
+		.name = "mp2888",
+		.of_match_table = of_match_ptr(mp2888_of_match),
+	},
+	.probe_new = mp2888_probe,
+	.id_table = mp2888_id,
+};
+
+module_i2c_driver(mp2888_driver);
+
+MODULE_AUTHOR("Vadim Pasternak <vadimp@nvidia.com>");
+MODULE_DESCRIPTION("PMBus driver for MPS MP2888 device");
+MODULE_LICENSE("GPL");
-- 
2.11.0

[PATCH hwmon-next 3/3] dt-bindings: Add MP2888 voltage regulator device

[Vadim Pasternak]

Monolithic Power Systems, Inc. (MPS) dual-loop, digital, multi-phase
controller.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
---
 Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index a327130d1faa..4f6d149bfb3f 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -98,6 +98,8 @@ properties:
           - fsl,mpl3115
             # MPR121: Proximity Capacitive Touch Sensor Controller
           - fsl,mpr121
+            # Monolithic Power Systems Inc. multi-phase controller mp2888
+          - mps,mp2888
             # Monolithic Power Systems Inc. multi-phase controller mp2975
           - mps,mp2975
             # G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface
-- 
2.11.0

Re: [PATCH hwmon-next 2/3] hwmon: (pmbus) Add support for MPS Multi-phase mp2888 controller

[Guenter Roeck]

On 4/8/21 7:17 AM, Vadim Pasternak wrote:
> Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
> vendor. This is a digital, multi-phase, pulse-width modulation
> controller.
> 
> This device supports:
> - One power rail.
> - Programmable Multi-Phase up to 10 Phases.
> - PWM-VID Interface
> - One pages 0 for telemetry.
> - Programmable pins for PMBus Address.
> - Built-In EEPROM to Store Custom Configurations.
> - Can configured VOUT readout in direct or VID format and allows
>   setting of different formats on rails 1 and 2. For VID the following
>   protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
>   10-mV DAC, IMVP9 mode with 5-mV DAC.
> 
> Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
> ---
>  Documentation/hwmon/mp2888.rst | 111 ++++++++++++++++++
>  drivers/hwmon/pmbus/Kconfig    |   9 ++
>  drivers/hwmon/pmbus/Makefile   |   1 +
>  drivers/hwmon/pmbus/mp2888.c   | 256 +++++++++++++++++++++++++++++++++++++++++
>  4 files changed, 377 insertions(+)
>  create mode 100644 Documentation/hwmon/mp2888.rst
>  create mode 100644 drivers/hwmon/pmbus/mp2888.c
> 
> diff --git a/Documentation/hwmon/mp2888.rst b/Documentation/hwmon/mp2888.rst
> new file mode 100644
> index 000000000000..7839a010642a
> --- /dev/null
> +++ b/Documentation/hwmon/mp2888.rst
> @@ -0,0 +1,111 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2888
> +====================
> +
> +Supported chips:
> +
> +  * MPS MP12254
> +
> +    Prefix: 'mp2888'
> +
> +Author:
> +
> +	Vadim Pasternak <vadimp@nvidia.com>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +vendor dual-loop, digital, multi-phase controller MP2888.
> +
> +This device: supports:
> +
> +- One power rail.
> +- Programmable Multi-Phase up to 10 Phases.
> +- PWM-VID Interface
> +- One pages 0 for telemetry.
> +- Programmable pins for PMBus Address.
> +- Built-In EEPROM to Store Custom Configurations.
> +
> +Device complaint with:
> +
> +- PMBus rev 1.3 interface.
> +
> +Device supports direct format for reading output current, output voltage,
> +input and output power and temperature.
> +Device supports linear format for reading input voltage and input power.
> +
> +The driver provides the next attributes for the current:
> +
> +- for current out input and maximum alarm;
> +- for phase current: input and label.
> +
> +The driver exports the following attributes via the 'sysfs' files, where:
> +
> +- 'n' is number of configured phases (from 1 to 10);
> +- index 1 for "iout";
> +- indexes 2 ... 1 + n for phases.
> +
> +**curr1_alarm**
> +
> +**curr[1-{1+n}]_input**
> +
> +**curr[1-{1+n}]_label**
> +
> +The driver provides the next attributes for the voltage:
> +
> +- for voltage in: input, low and high critical thresholds, low and high
> +  critical alarms;
> +- for voltage out: input and high alarm;
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +
> +**in1_crit**
> +
> +**in1_crit_alarm**
> +
> +**in1_input**
> +
> +**in1_label**
> +
> +**in1_min**
> +
> +**in1_min_alarm**
> +
> +**in2_alarm**
> +
> +**in2_input**
> +
> +**in2_label**
> +
> +The driver provides the next attributes for the power:
> +
> +- for power in alarm and input.
> +- for power out: cap, cap alarm an input.
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +- indexes 1 for "pin";
> +- indexes 2 for "pout";
> +
> +**power1_alarm**
> +
> +**power1_input**
> +
> +**power1_label**
> +
> +**power2_cap**
> +
> +**power2_cap_alarm**
> +
> +**power2_input**
> +
> +**power2_label**
> +
> +The driver provides the next attributes for the temperature:
> +
> +**temp1_input**
> +
> +**temp1_max**
> +
> +**temp1_max_alarm**
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 32d2fc850621..a57571928b31 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -211,6 +211,15 @@ config SENSORS_MAX8688
>  	  This driver can also be built as a module. If so, the module will
>  	  be called max8688.
>  
> +config SENSORS_MP2888
> +	tristate "MPS MP2888"
> +	help
> +	  If you say yes here you get hardware monitoring support for MPS
> +	  MP2888 Digital, Multi-Phase, Pulse-Width Modulation Controller.
> +
> +	  This driver can also be built as a module. If so, the module will
> +	  be called mp2888.
> +
>  config SENSORS_MP2975
>  	tristate "MPS MP2975"
>  	help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index 6a4ba0fdc1db..a6d7352621ca 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
>  obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
>  obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
>  obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
> +obj-$(CONFIG_SENSORS_MP2888)	+= mp2888.o
>  obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
>  obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
>  obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2888.c b/drivers/hwmon/pmbus/mp2888.c
> new file mode 100644
> index 000000000000..3d4b272616c6
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2888.c
> @@ -0,0 +1,256 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers
> + *
> + * Copyright (C) 2020 Nvidia Technologies Ltd.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +/* Vendor specific registers. */
> +#define MP2888_MFR_SYS_CONFIG	0x44
> +#define MP2888_MFR_VR_CONFIG1	0xe1
> +
> +#define MP2888_TOTAL_CURRENT_RESOLUTION	BIT(3)
> +#define MP2888_VIN_LIMIT_UNIT		8
> +#define MP2888_VIN_UNIT			3125
> +#define MP2888_TEMP_UNIT		10
> +#define MP2888_MAX_PHASE		10
> +
> +struct mp2888_data {
> +	struct pmbus_driver_info info;
> +	int total_curr_resolution;
> +};
> +
> +#define to_mp2888_data(x)  container_of(x, struct mp2888_data, info)
> +
> +static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
> +{
> +	switch (reg) {
> +	case PMBUS_VOUT_MODE:
> +		/* Enforce VOUT direct format. */
> +		return PB_VOUT_MODE_DIRECT;
> +	default:
> +		return -ENODATA;
> +	}
> +}
> +
> +static int
> +mp2888_read_word_helper(struct i2c_client *client, int page, int phase, u8 reg, u16 mask)
> +{
> +	int ret = pmbus_read_word_data(client, page, phase, reg);
> +
> +	return (ret > 0) ? ret & mask : ret;
> +}
> +
> +static int mp2888_read_word_data(struct i2c_client *client, int page, int phase, int reg)
> +{
> +	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
> +	struct mp2888_data *data = to_mp2888_data(info);
> +	int ret;
> +
> +	switch (reg) {
> +	case PMBUS_OT_WARN_LIMIT:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(7, 0));
> +		break;

Explanation needed: The register map states that the upper bits read 0.
If that is unreliable, it needs to be documented here. This applies
to all masked operations.

> +	case PMBUS_VIN_OV_FAULT_LIMIT:
> +	case PMBUS_VIN_UV_WARN_LIMIT:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(7, 0));
> +		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, MP2888_VIN_LIMIT_UNIT);

Limits are linear, and the exponent is supposed to be reported in the register.
Why override it ? Seems to me this code causes resolution loss.

> +		break;
> +	case PMBUS_READ_VIN:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(9, 0));
> +		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret * MP2888_VIN_UNIT, 100000);
> +		break;

Again, this must cause a significant loss of accuracy. Why not just add in the linear11
exponent ?

> +	case PMBUS_READ_VOUT:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
> +		break;
> +	case PMBUS_READ_TEMPERATURE_1:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
> +		ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, MP2888_TEMP_UNIT);

Better use linear11 and add the exponent (or fix the coefficients).

> +		break;
> +	case PMBUS_READ_IOUT:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
> +		ret = (ret < 0) ? ret : data->total_curr_resolution ? DIV_ROUND_CLOSEST(ret, 2) :
> +		      DIV_ROUND_CLOSEST(ret, 4);

I understand this can't use linear11 because that would drop/misinterpret the
upper bits, but it would be better to adjust the coefficients instead of
accepting a loss of accuracy here.

> +		/*
> +		 * Current phase sensing, providing by the device through the dedicated
> +		 * registers 73h - 77h is not accurate, because sampling of current occurrence of
> +		 * bit weight has a big deviation. Calculate per-phase current as total current
> +		 * divided by number phases.
> +		 */
> +		if (phase != 0xff)
> +			ret = (ret < 0) ? ret : DIV_ROUND_CLOSEST(ret, data->info.phases[page]);

If this is indeed the case, I'd argue that phase support is quite useless. The whole point
of it is to show load per phase, even if it is not perfect. Either live with the inaccuracy
and document it, or drop multi-phase support (and document why it isn't supported).

Note that all multi-phase controllers I have seen report inaccurate currents for the multiple
phases.

> +		break;
> +	case PMBUS_READ_POUT:
> +	case PMBUS_READ_PIN:
> +		ret = mp2888_read_word_helper(client, page, phase, reg, GENMASK(11, 0));
> +		ret = (ret < 0) ? ret : data->total_curr_resolution ? ret :
> +		      DIV_ROUND_CLOSEST(ret, 2);

Same as above. Adjusting coefficients would be better and easier than loss
of resolution.

> +		break;
> +	case PMBUS_OT_FAULT_LIMIT:
> +	case PMBUS_UT_WARN_LIMIT:
> +	case PMBUS_UT_FAULT_LIMIT:
> +	case PMBUS_VIN_UV_FAULT_LIMIT:
> +	case PMBUS_VOUT_UV_WARN_LIMIT:
> +	case PMBUS_VOUT_OV_WARN_LIMIT:
> +	case PMBUS_VOUT_UV_FAULT_LIMIT:
> +	case PMBUS_VOUT_OV_FAULT_LIMIT:
> +	case PMBUS_VIN_OV_WARN_LIMIT:
> +	case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
> +	case PMBUS_IOUT_OC_WARN_LIMIT:
> +	case PMBUS_IOUT_OC_FAULT_LIMIT:
> +	case PMBUS_IOUT_UC_FAULT_LIMIT:
> +	case PMBUS_POUT_OP_FAULT_LIMIT:
> +	case PMBUS_POUT_OP_WARN_LIMIT:
> +	case PMBUS_PIN_OP_WARN_LIMIT:
> +	case PMBUS_MFR_VIN_MIN:
> +	case PMBUS_MFR_VIN_MAX:
> +	case PMBUS_MFR_VOUT_MAX:
> +	case PMBUS_MFR_IIN_MAX:
> +	case PMBUS_MFR_IOUT_MAX:
> +	case PMBUS_MFR_PIN_MAX:
> +	case PMBUS_MFR_POUT_MAX:
> +	case PMBUS_MFR_MAX_TEMP_1:
> +		return -ENXIO;

This needs explanation. Does the chip misbehave if accesses to those registers
are attempted ? If so, document/explain it. Otherwise drop the code.

> +	default:
> +		return -ENODATA;
> +	}
> +
> +	return ret;
> +}
> +
> +static void mp2888_set_phase(struct pmbus_driver_info *info)
> +{
> +	int i;
> +
> +	for (i = 0 ; i < info->phases[0]; i++)
> +		info->pfunc[i] = PMBUS_HAVE_IOUT;

You can just set that statically. It won't be used if a phase is disabled.

> +}
> +
> +static int
> +mp2888_identify_multiphase(struct i2c_client *client, struct mp2888_data *data,
> +			   struct pmbus_driver_info *info)
> +{
> +	int ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Identify multiphase number - could be from 1 to 10. */
> +	ret = i2c_smbus_read_word_data(client, MP2888_MFR_VR_CONFIG1);
> +	if (ret <= 0)
> +		return ret;
> +
> +	info->phases[0] = ret & GENMASK(3, 0);
> +
> +	/*
> +	 * The device provides a total of 10 PWM pins, and can be configured to different phase
> +	 * count applications for rail.
> +	 */
> +	if (info->phases[0] > MP2888_MAX_PHASE)
> +		return -EINVAL;
> +
> +	mp2888_set_phase(info);
> +
> +	return 0;
> +}
> +
> +static int mp2888_current_resolution_get(struct i2c_client *client, struct mp2888_data *data)
> +{
> +	int ret;
> +
> +	/*
> +	 * Obtain resolution selector for total current report and protection.
> +	 * 0: original resolution; 1: half resolution (in such case phase current value should
> +	 * be doubled.
> +	 */
> +	ret = i2c_smbus_read_word_data(client, MP2888_MFR_SYS_CONFIG);
> +	if (ret < 0)
> +		return ret;
> +	data->total_curr_resolution = (ret & MP2888_TOTAL_CURRENT_RESOLUTION) >> 3;
> +
> +	return 0;
> +}
> +
> +static struct pmbus_driver_info mp2888_info = {
> +	.pages = 1,
> +	.format[PSC_VOLTAGE_IN] = linear,
> +	.format[PSC_VOLTAGE_OUT] = direct,
> +	.format[PSC_TEMPERATURE] = direct,
> +	.format[PSC_CURRENT_IN] = linear,
> +	.format[PSC_CURRENT_OUT] = direct,
> +	.format[PSC_POWER] = direct,
> +	.m[PSC_TEMPERATURE] = 1,
> +	.m[PSC_VOLTAGE_OUT] = 1,
> +	.R[PSC_VOLTAGE_OUT] = 3,
> +	.m[PSC_CURRENT_OUT] = 1,
> +	.m[PSC_POWER] = 1,
> +	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT |
> +		   PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> +		   PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
> +		   PMBUS_PHASE_VIRTUAL,
> +	.read_byte_data = mp2888_read_byte_data,
> +	.read_word_data = mp2888_read_word_data,
> +};
> +
> +static int mp2888_probe(struct i2c_client *client)
> +{
> +	struct pmbus_driver_info *info;
> +	struct mp2888_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(&client->dev, sizeof(struct mp2888_data),
> +			    GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	memcpy(&data->info, &mp2888_info, sizeof(*info));
> +	info = &data->info;
> +
> +	/* Identify multiphase configuration. */
> +	ret = mp2888_identify_multiphase(client, data, info);
> +	if (ret)
> +		return ret;
> +
> +	/* Obtain total current resolution. */
> +	ret = mp2888_current_resolution_get(client, data);
> +	if (ret)
> +		return ret;
> +
> +	return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2888_id[] = {
> +	{"mp2888", 0},
> +	{}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2888_id);
> +
> +static const struct of_device_id __maybe_unused mp2888_of_match[] = {
> +	{.compatible = "mps,mp2888"},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, mp2888_of_match);
> +
> +static struct i2c_driver mp2888_driver = {
> +	.driver = {
> +		.name = "mp2888",
> +		.of_match_table = of_match_ptr(mp2888_of_match),
> +	},
> +	.probe_new = mp2888_probe,
> +	.id_table = mp2888_id,
> +};
> +
> +module_i2c_driver(mp2888_driver);
> +
> +MODULE_AUTHOR("Vadim Pasternak <vadimp@nvidia.com>");
> +MODULE_DESCRIPTION("PMBus driver for MPS MP2888 device");
> +MODULE_LICENSE("GPL");
> 

Re: [PATCH hwmon-next 3/3] dt-bindings: Add MP2888 voltage regulator device

[Rob Herring]

On Thu, 08 Apr 2021 17:17:26 +0300, Vadim Pasternak wrote:
> Monolithic Power Systems, Inc. (MPS) dual-loop, digital, multi-phase
> controller.
> 
> Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
> ---
>  Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>