From: Claudiu Beznea <claudiu.beznea@microchip.com> To: <nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>, <ludovic.desroches@microchip.com>, <robh+dt@kernel.org>, <linux@armlinux.org.uk> Cc: <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Claudiu Beznea <claudiu.beznea@microchip.com> Subject: [PATCH v2 20/24] ARM: at91: pm: add backup mode support for SAMA7G5 Date: Fri, 9 Apr 2021 14:13:41 +0300 [thread overview] Message-ID: <20210409111345.294472-21-claudiu.beznea@microchip.com> (raw) In-Reply-To: <20210409111345.294472-1-claudiu.beznea@microchip.com> Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin to shutdown controller. This will signal to PMIC that it needs to switch to the state corresponding to backup mode. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> --- arch/arm/mach-at91/pm.c | 3 ++- arch/arm/mach-at91/pm_suspend.S | 7 +++++++ 2 files changed, 9 insertions(+), 1 deletion(-) diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 91b4014d2e10..fcb20272d65d 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -729,7 +729,8 @@ static int __init at91_pm_backup_init(void) struct platform_device *pdev; int ret = -ENODEV, located = 0; - if (!IS_ENABLED(CONFIG_SOC_SAMA5D2)) + if (!IS_ENABLED(CONFIG_SOC_SAMA5D2) && + !IS_ENABLED(CONFIG_SOC_SAMA7G5)) return -EPERM; if (!at91_is_pm_mode_active(AT91_PM_BACKUP)) diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S index 7396e18dd7e5..cbd61a3bcab1 100644 --- a/arch/arm/mach-at91/pm_suspend.S +++ b/arch/arm/mach-at91/pm_suspend.S @@ -106,6 +106,12 @@ lp_done_\ena: #endif .endm + .macro at91_backup_set_lpm reg +#ifdef CONFIG_SOC_SAMA7 + orr \reg, \reg, #0x200000 +#endif + .endm + .text .arm @@ -989,6 +995,7 @@ ulp_exit: ldr r0, .shdwc mov tmp1, #0xA5000000 add tmp1, tmp1, #0x1 + at91_backup_set_lpm tmp1 str tmp1, [r0, #0] .endm -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Claudiu Beznea <claudiu.beznea@microchip.com> To: <nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>, <ludovic.desroches@microchip.com>, <robh+dt@kernel.org>, <linux@armlinux.org.uk> Cc: <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Claudiu Beznea <claudiu.beznea@microchip.com> Subject: [PATCH v2 20/24] ARM: at91: pm: add backup mode support for SAMA7G5 Date: Fri, 9 Apr 2021 14:13:41 +0300 [thread overview] Message-ID: <20210409111345.294472-21-claudiu.beznea@microchip.com> (raw) In-Reply-To: <20210409111345.294472-1-claudiu.beznea@microchip.com> Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin to shutdown controller. This will signal to PMIC that it needs to switch to the state corresponding to backup mode. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> --- arch/arm/mach-at91/pm.c | 3 ++- arch/arm/mach-at91/pm_suspend.S | 7 +++++++ 2 files changed, 9 insertions(+), 1 deletion(-) diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 91b4014d2e10..fcb20272d65d 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -729,7 +729,8 @@ static int __init at91_pm_backup_init(void) struct platform_device *pdev; int ret = -ENODEV, located = 0; - if (!IS_ENABLED(CONFIG_SOC_SAMA5D2)) + if (!IS_ENABLED(CONFIG_SOC_SAMA5D2) && + !IS_ENABLED(CONFIG_SOC_SAMA7G5)) return -EPERM; if (!at91_is_pm_mode_active(AT91_PM_BACKUP)) diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S index 7396e18dd7e5..cbd61a3bcab1 100644 --- a/arch/arm/mach-at91/pm_suspend.S +++ b/arch/arm/mach-at91/pm_suspend.S @@ -106,6 +106,12 @@ lp_done_\ena: #endif .endm + .macro at91_backup_set_lpm reg +#ifdef CONFIG_SOC_SAMA7 + orr \reg, \reg, #0x200000 +#endif + .endm + .text .arm @@ -989,6 +995,7 @@ ulp_exit: ldr r0, .shdwc mov tmp1, #0xA5000000 add tmp1, tmp1, #0x1 + at91_backup_set_lpm tmp1 str tmp1, [r0, #0] .endm -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-04-09 11:18 UTC|newest] Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-04-09 11:13 [PATCH v2 00/24] ARM: at91: pm: add support for sama7g5 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 01/24] ARM: at91: pm: move pm_bu to soc_pm data structure Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 02/24] ARM: at91: pm: move the setup of soc_pm.bu->suspended Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 03/24] ARM: at91: pm: document at91_soc_pm structure Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 04/24] ARM: at91: pm: check for different controllers in at91_pm_modes_init() Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 05/24] ARM: at91: pm: do not initialize pdev Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 06/24] ARM: at91: pm: use r7 instead of tmp1 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 07/24] ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 08/24] ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 09/24] ARM: at91: pm: add support for waiting MCK1..4 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 10/24] ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 11/24] ARM: at91: ddr: add registers definitions for sama7g5's ddr Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 12/24] ARM: at91: pm: add self-refresh support for sama7g5 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 13/24] ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 14/24] ARM: at91: pm: add support for 2.5V LDO regulator control Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 15/24] ARM: at91: pm: wait for ddr power mode off Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 16/24] dt-bindings: atmel-sysreg: add bindings for sama7g5 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-12 16:02 ` Rob Herring 2021-04-12 16:02 ` Rob Herring 2021-04-15 7:31 ` Claudiu.Beznea 2021-04-15 7:31 ` Claudiu.Beznea 2021-04-09 11:13 ` [PATCH v2 17/24] ARM: at91: pm: add sama7g5 ddr controller Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 18/24] ARM: at91: pm: add sama7g5 ddr phy controller Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 19/24] ARM: at91: pm: save ddr phy calibration data to securam Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea [this message] 2021-04-09 11:13 ` [PATCH v2 20/24] ARM: at91: pm: add backup mode support for SAMA7G5 Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 21/24] ARM: at91: pm: add sama7g5's pmc Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 22/24] ARM: at91: sama7: introduce sama7 SoC family Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 23/24] ARM: at91: pm: add pm support for SAMA7G5 Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea 2021-04-09 11:13 ` [PATCH v2 24/24] ARM: at91: pm: add sama7g5 shdwc Claudiu Beznea 2021-04-09 11:13 ` Claudiu Beznea
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210409111345.294472-21-claudiu.beznea@microchip.com \ --to=claudiu.beznea@microchip.com \ --cc=alexandre.belloni@bootlin.com \ --cc=devicetree@vger.kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux@armlinux.org.uk \ --cc=ludovic.desroches@microchip.com \ --cc=nicolas.ferre@microchip.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.