* [PATCH net-next 0/2] net: phy: marvell-88x2222: a couple of improvements @ 2021-04-12 12:16 Ivan Bornyakov 2021-04-12 12:16 ` [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational Ivan Bornyakov 2021-04-12 12:17 ` [PATCH net-next 2/2] net: phy: marvell-88x2222: swap 1G/10G modes on autoneg Ivan Bornyakov 0 siblings, 2 replies; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-12 12:16 UTC (permalink / raw) Cc: Ivan Bornyakov, system, andrew, hkallweit1, linux, davem, kuba, netdev, linux-kernel First, there are some SFP modules that only uses RX_LOS for link indication. Add check that SFP link is operational before actual read of link status. Second, it is invalid to set 10G speed without autonegotiation, according to phy_ethtool_ksettings_set(). Implement switching between 10GBase-R and 1000Base-X/SGMII if autonegotiation can't complete but there is signal in line. Ivan Bornyakov (2): net: phy: marvell-88x2222: check that link is operational net: phy: marvell-88x2222: swap 1G/10G modes on autoneg drivers/net/phy/marvell-88x2222.c | 296 +++++++++++++++++++----------- 1 file changed, 191 insertions(+), 105 deletions(-) -- 2.26.3 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-12 12:16 [PATCH net-next 0/2] net: phy: marvell-88x2222: a couple of improvements Ivan Bornyakov @ 2021-04-12 12:16 ` Ivan Bornyakov 2021-04-12 23:32 ` Marek Behún 2021-04-12 23:40 ` Andrew Lunn 2021-04-12 12:17 ` [PATCH net-next 2/2] net: phy: marvell-88x2222: swap 1G/10G modes on autoneg Ivan Bornyakov 1 sibling, 2 replies; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-12 12:16 UTC (permalink / raw) Cc: Ivan Bornyakov, system, andrew, hkallweit1, linux, davem, kuba, netdev, linux-kernel Some SFP modules uses RX_LOS for link indication. In such cases link will be always up, even without cable connected. RX_LOS changes will trigger link_up()/link_down() upstream operations. Thus, check that SFP link is operational before actual read link status. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> --- drivers/net/phy/marvell-88x2222.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c index eca8c2f20684..fb285ac741b2 100644 --- a/drivers/net/phy/marvell-88x2222.c +++ b/drivers/net/phy/marvell-88x2222.c @@ -51,6 +51,7 @@ struct mv2222_data { phy_interface_t line_interface; __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); + bool sfp_link; }; /* SFI PMA transmit enable */ @@ -148,6 +149,9 @@ static int mv2222_read_status(struct phy_device *phydev) phydev->speed = SPEED_UNKNOWN; phydev->duplex = DUPLEX_UNKNOWN; + if (!priv->sfp_link) + return 0; + if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) link = mv2222_read_status_10g(phydev); else @@ -446,9 +450,31 @@ static void mv2222_sfp_remove(void *upstream) linkmode_zero(priv->supported); } +static void mv2222_sfp_link_up(void *upstream) +{ + struct phy_device *phydev = upstream; + struct mv2222_data *priv; + + priv = (struct mv2222_data *)phydev->priv; + + priv->sfp_link = true; +} + +static void mv2222_sfp_link_down(void *upstream) +{ + struct phy_device *phydev = upstream; + struct mv2222_data *priv; + + priv = (struct mv2222_data *)phydev->priv; + + priv->sfp_link = false; +} + static const struct sfp_upstream_ops sfp_phy_ops = { .module_insert = mv2222_sfp_insert, .module_remove = mv2222_sfp_remove, + .link_up = mv2222_sfp_link_up, + .link_down = mv2222_sfp_link_down, .attach = phy_sfp_attach, .detach = phy_sfp_detach, }; -- 2.26.3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-12 12:16 ` [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational Ivan Bornyakov @ 2021-04-12 23:32 ` Marek Behún 2021-04-13 7:13 ` Ivan Bornyakov 2021-04-12 23:40 ` Andrew Lunn 1 sibling, 1 reply; 12+ messages in thread From: Marek Behún @ 2021-04-12 23:32 UTC (permalink / raw) To: Ivan Bornyakov Cc: system, andrew, hkallweit1, linux, davem, kuba, netdev, linux-kernel On Mon, 12 Apr 2021 15:16:59 +0300 Ivan Bornyakov <i.bornyakov@metrotek.ru> wrote: > Some SFP modules uses RX_LOS for link indication. In such cases link > will be always up, even without cable connected. RX_LOS changes will > trigger link_up()/link_down() upstream operations. Thus, check that SFP > link is operational before actual read link status. > > Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> > --- > drivers/net/phy/marvell-88x2222.c | 26 ++++++++++++++++++++++++++ > 1 file changed, 26 insertions(+) > > diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c > index eca8c2f20684..fb285ac741b2 100644 > --- a/drivers/net/phy/marvell-88x2222.c > +++ b/drivers/net/phy/marvell-88x2222.c > @@ -51,6 +51,7 @@ > struct mv2222_data { > phy_interface_t line_interface; > __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); > + bool sfp_link; > }; > > /* SFI PMA transmit enable */ > @@ -148,6 +149,9 @@ static int mv2222_read_status(struct phy_device *phydev) > phydev->speed = SPEED_UNKNOWN; > phydev->duplex = DUPLEX_UNKNOWN; > > + if (!priv->sfp_link) > + return 0; > + So if SFP is not used at all, if this PHY is used in a different usecase, this function will always return 0? Is this correct? > if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) > link = mv2222_read_status_10g(phydev); > else > @@ -446,9 +450,31 @@ static void mv2222_sfp_remove(void *upstream) > linkmode_zero(priv->supported); > } > > +static void mv2222_sfp_link_up(void *upstream) > +{ > + struct phy_device *phydev = upstream; > + struct mv2222_data *priv; > + > + priv = (struct mv2222_data *)phydev->priv; > + > + priv->sfp_link = true; > +} > + > +static void mv2222_sfp_link_down(void *upstream) > +{ > + struct phy_device *phydev = upstream; > + struct mv2222_data *priv; > + > + priv = (struct mv2222_data *)phydev->priv; This cast is redundant since the phydev->priv is (void*). You can cast (void*) to (struct ... *). You can also just use struct mv2222_data *priv = phydev->priv; > + > + priv->sfp_link = false; > +} > + > static const struct sfp_upstream_ops sfp_phy_ops = { > .module_insert = mv2222_sfp_insert, > .module_remove = mv2222_sfp_remove, > + .link_up = mv2222_sfp_link_up, > + .link_down = mv2222_sfp_link_down, > .attach = phy_sfp_attach, > .detach = phy_sfp_detach, > }; ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-12 23:32 ` Marek Behún @ 2021-04-13 7:13 ` Ivan Bornyakov 2021-04-13 13:07 ` Andrew Lunn 0 siblings, 1 reply; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-13 7:13 UTC (permalink / raw) To: Marek Behún Cc: system, andrew, hkallweit1, linux, davem, kuba, netdev, linux-kernel On Tue, Apr 13, 2021 at 01:32:12AM +0200, Marek Behún wrote: > On Mon, 12 Apr 2021 15:16:59 +0300 > Ivan Bornyakov <i.bornyakov@metrotek.ru> wrote: > > > Some SFP modules uses RX_LOS for link indication. In such cases link > > will be always up, even without cable connected. RX_LOS changes will > > trigger link_up()/link_down() upstream operations. Thus, check that SFP > > link is operational before actual read link status. > > > > Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> > > --- > > drivers/net/phy/marvell-88x2222.c | 26 ++++++++++++++++++++++++++ > > 1 file changed, 26 insertions(+) > > > > diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c > > index eca8c2f20684..fb285ac741b2 100644 > > --- a/drivers/net/phy/marvell-88x2222.c > > +++ b/drivers/net/phy/marvell-88x2222.c > > @@ -51,6 +51,7 @@ > > struct mv2222_data { > > phy_interface_t line_interface; > > __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); > > + bool sfp_link; > > }; > > > > /* SFI PMA transmit enable */ > > @@ -148,6 +149,9 @@ static int mv2222_read_status(struct phy_device *phydev) > > phydev->speed = SPEED_UNKNOWN; > > phydev->duplex = DUPLEX_UNKNOWN; > > > > + if (!priv->sfp_link) > > + return 0; > > + > > So if SFP is not used at all, if this PHY is used in a different > usecase, this function will always return 0? Is this correct? > Yes, probably. The thing is that I only have hardware with SFP cages, so I realy don't know if this driver work in other usecases. The good thing about open source is that other developers with different hardware configurations can rework here and there and contribute back. Right? > > if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) > > link = mv2222_read_status_10g(phydev); > > else > > @@ -446,9 +450,31 @@ static void mv2222_sfp_remove(void *upstream) > > linkmode_zero(priv->supported); > > } > > > > +static void mv2222_sfp_link_up(void *upstream) > > +{ > > + struct phy_device *phydev = upstream; > > + struct mv2222_data *priv; > > + > > + priv = (struct mv2222_data *)phydev->priv; > > + > > + priv->sfp_link = true; > > +} > > + > > +static void mv2222_sfp_link_down(void *upstream) > > +{ > > + struct phy_device *phydev = upstream; > > + struct mv2222_data *priv; > > + > > + priv = (struct mv2222_data *)phydev->priv; > > This cast is redundant since the phydev->priv is (void*). You can cast > (void*) to (struct ... *). > > You can also just use > struct mv2222_data *priv = phydev->priv; > Yeah, I know, but reverse XMAS tree wouldn't line up. > > + > > + priv->sfp_link = false; > > +} > > + > > static const struct sfp_upstream_ops sfp_phy_ops = { > > .module_insert = mv2222_sfp_insert, > > .module_remove = mv2222_sfp_remove, > > + .link_up = mv2222_sfp_link_up, > > + .link_down = mv2222_sfp_link_down, > > .attach = phy_sfp_attach, > > .detach = phy_sfp_detach, > > }; > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-13 7:13 ` Ivan Bornyakov @ 2021-04-13 13:07 ` Andrew Lunn 0 siblings, 0 replies; 12+ messages in thread From: Andrew Lunn @ 2021-04-13 13:07 UTC (permalink / raw) To: Ivan Bornyakov Cc: Marek Behún, system, hkallweit1, linux, davem, kuba, netdev, linux-kernel On Tue, Apr 13, 2021 at 10:13:49AM +0300, Ivan Bornyakov wrote: > On Tue, Apr 13, 2021 at 01:32:12AM +0200, Marek Behún wrote: > > On Mon, 12 Apr 2021 15:16:59 +0300 > > Ivan Bornyakov <i.bornyakov@metrotek.ru> wrote: > > > > > Some SFP modules uses RX_LOS for link indication. In such cases link > > > will be always up, even without cable connected. RX_LOS changes will > > > trigger link_up()/link_down() upstream operations. Thus, check that SFP > > > link is operational before actual read link status. > > > > > > Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> > > > --- > > > drivers/net/phy/marvell-88x2222.c | 26 ++++++++++++++++++++++++++ > > > 1 file changed, 26 insertions(+) > > > > > > diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c > > > index eca8c2f20684..fb285ac741b2 100644 > > > --- a/drivers/net/phy/marvell-88x2222.c > > > +++ b/drivers/net/phy/marvell-88x2222.c > > > @@ -51,6 +51,7 @@ > > > struct mv2222_data { > > > phy_interface_t line_interface; > > > __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); > > > + bool sfp_link; > > > }; > > > > > > /* SFI PMA transmit enable */ > > > @@ -148,6 +149,9 @@ static int mv2222_read_status(struct phy_device *phydev) > > > phydev->speed = SPEED_UNKNOWN; > > > phydev->duplex = DUPLEX_UNKNOWN; > > > > > > + if (!priv->sfp_link) > > > + return 0; > > > + > > > > So if SFP is not used at all, if this PHY is used in a different > > usecase, this function will always return 0? Is this correct? > > > > Yes, probably. The thing is that I only have hardware with SFP cages, so > I realy don't know if this driver work in other usecases. It is O.K, to say you don't know if this will work for other setups, but it is different thing to do something which could potentially break those other setup. Somebody trying to use this without an SFP is going to have a bad experience because of this change. And then they are going to have to try to fix this, potentially breaking your setup. if you truly need this, make it conditional on that you know you have an SFP cage connected. > > > +static void mv2222_sfp_link_down(void *upstream) > > > +{ > > > + struct phy_device *phydev = upstream; > > > + struct mv2222_data *priv; > > > + > > > + priv = (struct mv2222_data *)phydev->priv; > > > > This cast is redundant since the phydev->priv is (void*). You can cast > > (void*) to (struct ... *). > > > > You can also just use > > struct mv2222_data *priv = phydev->priv; > > > > Yeah, I know, but reverse XMAS tree wouldn't line up. Please move the assignment into the body of the function. Andrew ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-12 12:16 ` [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational Ivan Bornyakov 2021-04-12 23:32 ` Marek Behún @ 2021-04-12 23:40 ` Andrew Lunn 2021-04-13 7:19 ` Ivan Bornyakov 1 sibling, 1 reply; 12+ messages in thread From: Andrew Lunn @ 2021-04-12 23:40 UTC (permalink / raw) To: Ivan Bornyakov Cc: system, hkallweit1, linux, davem, kuba, netdev, linux-kernel On Mon, Apr 12, 2021 at 03:16:59PM +0300, Ivan Bornyakov wrote: > Some SFP modules uses RX_LOS for link indication. In such cases link > will be always up, even without cable connected. RX_LOS changes will > trigger link_up()/link_down() upstream operations. Thus, check that SFP > link is operational before actual read link status. Sorry, but this is not making much sense to me. LOS just indicates some sort of light is coming into the device. You have no idea what sort of light. The transceiver might be able to decode that light and get sync, it might not. It is important that mv2222_read_status() returns the line side status. Has it been able to achieve sync? That should be independent of LOS. Or are you saying the transceiver is reporting sync, despite no light coming in? Andrew ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-12 23:40 ` Andrew Lunn @ 2021-04-13 7:19 ` Ivan Bornyakov 2021-04-13 9:23 ` Russell King - ARM Linux admin 0 siblings, 1 reply; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-13 7:19 UTC (permalink / raw) To: Andrew Lunn; +Cc: system, hkallweit1, linux, davem, kuba, netdev, linux-kernel On Tue, Apr 13, 2021 at 01:40:32AM +0200, Andrew Lunn wrote: > On Mon, Apr 12, 2021 at 03:16:59PM +0300, Ivan Bornyakov wrote: > > Some SFP modules uses RX_LOS for link indication. In such cases link > > will be always up, even without cable connected. RX_LOS changes will > > trigger link_up()/link_down() upstream operations. Thus, check that SFP > > link is operational before actual read link status. > > Sorry, but this is not making much sense to me. > > LOS just indicates some sort of light is coming into the device. You > have no idea what sort of light. The transceiver might be able to > decode that light and get sync, it might not. It is important that > mv2222_read_status() returns the line side status. Has it been able to > achieve sync? That should be independent of LOS. Or are you saying the > transceiver is reporting sync, despite no light coming in? > > Andrew Yes, with some SFP modules transceiver is reporting sync despite no light coming in. So, the idea is to check that link is somewhat operational before determing line-side status. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-13 7:19 ` Ivan Bornyakov @ 2021-04-13 9:23 ` Russell King - ARM Linux admin 2021-04-13 10:06 ` Ivan Bornyakov 2021-04-13 13:12 ` Andrew Lunn 0 siblings, 2 replies; 12+ messages in thread From: Russell King - ARM Linux admin @ 2021-04-13 9:23 UTC (permalink / raw) To: Ivan Bornyakov Cc: Andrew Lunn, system, hkallweit1, davem, kuba, netdev, linux-kernel On Tue, Apr 13, 2021 at 10:19:30AM +0300, Ivan Bornyakov wrote: > On Tue, Apr 13, 2021 at 01:40:32AM +0200, Andrew Lunn wrote: > > On Mon, Apr 12, 2021 at 03:16:59PM +0300, Ivan Bornyakov wrote: > > > Some SFP modules uses RX_LOS for link indication. In such cases link > > > will be always up, even without cable connected. RX_LOS changes will > > > trigger link_up()/link_down() upstream operations. Thus, check that SFP > > > link is operational before actual read link status. > > > > Sorry, but this is not making much sense to me. > > > > LOS just indicates some sort of light is coming into the device. You > > have no idea what sort of light. The transceiver might be able to > > decode that light and get sync, it might not. It is important that > > mv2222_read_status() returns the line side status. Has it been able to > > achieve sync? That should be independent of LOS. Or are you saying the > > transceiver is reporting sync, despite no light coming in? > > > > Andrew > > Yes, with some SFP modules transceiver is reporting sync despite no > light coming in. So, the idea is to check that link is somewhat > operational before determing line-side status. Indeed - it should be a logical and operation - there is light present _and_ the PHY recognises the signal. This is what the commit achieves, although (iirc) doesn't cater for the case where there is no SFP cage attached. -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last! ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-13 9:23 ` Russell King - ARM Linux admin @ 2021-04-13 10:06 ` Ivan Bornyakov 2021-04-13 13:12 ` Andrew Lunn 1 sibling, 0 replies; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-13 10:06 UTC (permalink / raw) To: Russell King - ARM Linux admin Cc: Andrew Lunn, system, hkallweit1, davem, kuba, netdev, linux-kernel On Tue, Apr 13, 2021 at 10:23:48AM +0100, Russell King - ARM Linux admin wrote: > On Tue, Apr 13, 2021 at 10:19:30AM +0300, Ivan Bornyakov wrote: > > On Tue, Apr 13, 2021 at 01:40:32AM +0200, Andrew Lunn wrote: > > > On Mon, Apr 12, 2021 at 03:16:59PM +0300, Ivan Bornyakov wrote: > > > > Some SFP modules uses RX_LOS for link indication. In such cases link > > > > will be always up, even without cable connected. RX_LOS changes will > > > > trigger link_up()/link_down() upstream operations. Thus, check that SFP > > > > link is operational before actual read link status. > > > > > > Sorry, but this is not making much sense to me. > > > > > > LOS just indicates some sort of light is coming into the device. You > > > have no idea what sort of light. The transceiver might be able to > > > decode that light and get sync, it might not. It is important that > > > mv2222_read_status() returns the line side status. Has it been able to > > > achieve sync? That should be independent of LOS. Or are you saying the > > > transceiver is reporting sync, despite no light coming in? > > > > > > Andrew > > > > Yes, with some SFP modules transceiver is reporting sync despite no > > light coming in. So, the idea is to check that link is somewhat > > operational before determing line-side status. > > Indeed - it should be a logical and operation - there is light present > _and_ the PHY recognises the signal. This is what the commit achieves, > although (iirc) doesn't cater for the case where there is no SFP cage > attached. > > -- > RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ > FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last! Correct, it does not, I only have HW with SFP cage attached. ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-13 9:23 ` Russell King - ARM Linux admin 2021-04-13 10:06 ` Ivan Bornyakov @ 2021-04-13 13:12 ` Andrew Lunn 2021-04-13 13:16 ` Russell King - ARM Linux admin 1 sibling, 1 reply; 12+ messages in thread From: Andrew Lunn @ 2021-04-13 13:12 UTC (permalink / raw) To: Russell King - ARM Linux admin Cc: Ivan Bornyakov, system, hkallweit1, davem, kuba, netdev, linux-kernel > Indeed - it should be a logical and operation - there is light present > _and_ the PHY recognises the signal. This is what the commit achieves, > although (iirc) doesn't cater for the case where there is no SFP cage > attached. Hi Russell Is there something like this in the marvell10 driver? Also, do you know when there is an SFP cage? Do we need a standardised DT property for this? Andrew ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational 2021-04-13 13:12 ` Andrew Lunn @ 2021-04-13 13:16 ` Russell King - ARM Linux admin 0 siblings, 0 replies; 12+ messages in thread From: Russell King - ARM Linux admin @ 2021-04-13 13:16 UTC (permalink / raw) To: Andrew Lunn Cc: Ivan Bornyakov, system, hkallweit1, davem, kuba, netdev, linux-kernel Hi Andrew, On Tue, Apr 13, 2021 at 03:12:05PM +0200, Andrew Lunn wrote: > Is there something like this in the marvell10 driver? No, it doesn't seem to be necessary there - I haven't seen spontaneous link-ups with the 88x3310 there. Even if we did, that would cause other issues beyond a nusience link-up event, as the PHY selects the first media that has link between copper and fiber (and both are present on Macchiatobin platforms.) If the fiber indicates link up, it would prevent a copper connection being established. > Also, do you know when there is an SFP cage? Do we need a standardised > DT property for this? phydev->sfp_bus being non-NULL? -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last! ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH net-next 2/2] net: phy: marvell-88x2222: swap 1G/10G modes on autoneg 2021-04-12 12:16 [PATCH net-next 0/2] net: phy: marvell-88x2222: a couple of improvements Ivan Bornyakov 2021-04-12 12:16 ` [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational Ivan Bornyakov @ 2021-04-12 12:17 ` Ivan Bornyakov 1 sibling, 0 replies; 12+ messages in thread From: Ivan Bornyakov @ 2021-04-12 12:17 UTC (permalink / raw) Cc: Ivan Bornyakov, system, andrew, hkallweit1, linux, davem, kuba, netdev, linux-kernel Setting 10G without autonegotiation is invalid according to phy_ethtool_ksettings_set(). Thus, if autonegotiation can't complete for quite a time, but there is signal in line, switch line interface type to 10GBase-R, if supported, in hope for link to be established. And vice versa. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> --- drivers/net/phy/marvell-88x2222.c | 276 ++++++++++++++++++------------ 1 file changed, 168 insertions(+), 108 deletions(-) diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c index fb285ac741b2..d16c81f08334 100644 --- a/drivers/net/phy/marvell-88x2222.c +++ b/drivers/net/phy/marvell-88x2222.c @@ -48,6 +48,8 @@ #define MV_1GBX_PHY_STAT_SPEED100 BIT(14) #define MV_1GBX_PHY_STAT_SPEED1000 BIT(15) +#define AUTONEG_TIMEOUT 3 + struct mv2222_data { phy_interface_t line_interface; __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); @@ -82,89 +84,6 @@ static int mv2222_soft_reset(struct phy_device *phydev) 5000, 1000000, true); } -/* Returns negative on error, 0 if link is down, 1 if link is up */ -static int mv2222_read_status_10g(struct phy_device *phydev) -{ - int val, link = 0; - - val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_STAT1); - if (val < 0) - return val; - - if (val & MDIO_STAT1_LSTATUS) { - link = 1; - - /* 10GBASE-R do not support auto-negotiation */ - phydev->autoneg = AUTONEG_DISABLE; - phydev->speed = SPEED_10000; - phydev->duplex = DUPLEX_FULL; - } - - return link; -} - -/* Returns negative on error, 0 if link is down, 1 if link is up */ -static int mv2222_read_status_1g(struct phy_device *phydev) -{ - int val, link = 0; - - val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_STAT); - if (val < 0) - return val; - - if (!(val & BMSR_LSTATUS) || - (phydev->autoneg == AUTONEG_ENABLE && - !(val & BMSR_ANEGCOMPLETE))) - return 0; - - link = 1; - - val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_PHY_STAT); - if (val < 0) - return val; - - if (val & MV_1GBX_PHY_STAT_AN_RESOLVED) { - if (val & MV_1GBX_PHY_STAT_DUPLEX) - phydev->duplex = DUPLEX_FULL; - else - phydev->duplex = DUPLEX_HALF; - - if (val & MV_1GBX_PHY_STAT_SPEED1000) - phydev->speed = SPEED_1000; - else if (val & MV_1GBX_PHY_STAT_SPEED100) - phydev->speed = SPEED_100; - else - phydev->speed = SPEED_10; - } - - return link; -} - -static int mv2222_read_status(struct phy_device *phydev) -{ - struct mv2222_data *priv = phydev->priv; - int link; - - phydev->link = 0; - phydev->speed = SPEED_UNKNOWN; - phydev->duplex = DUPLEX_UNKNOWN; - - if (!priv->sfp_link) - return 0; - - if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) - link = mv2222_read_status_10g(phydev); - else - link = mv2222_read_status_1g(phydev); - - if (link < 0) - return link; - - phydev->link = link; - - return 0; -} - static int mv2222_disable_aneg(struct phy_device *phydev) { int ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_CTRL, @@ -252,6 +171,24 @@ static bool mv2222_is_1gbx_capable(struct phy_device *phydev) priv->supported); } +static bool mv2222_is_sgmii_capable(struct phy_device *phydev) +{ + struct mv2222_data *priv = phydev->priv; + + return (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, + priv->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, + priv->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, + priv->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, + priv->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, + priv->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, + priv->supported)); +} + static int mv2222_config_line(struct phy_device *phydev) { struct mv2222_data *priv = phydev->priv; @@ -271,7 +208,7 @@ static int mv2222_config_line(struct phy_device *phydev) } } -static int mv2222_setup_forced(struct phy_device *phydev) +static int mv2222_swap_line_type(struct phy_device *phydev) { struct mv2222_data *priv = phydev->priv; bool changed = false; @@ -279,25 +216,23 @@ static int mv2222_setup_forced(struct phy_device *phydev) switch (priv->line_interface) { case PHY_INTERFACE_MODE_10GBASER: - if (phydev->speed == SPEED_1000 && - mv2222_is_1gbx_capable(phydev)) { + if (mv2222_is_1gbx_capable(phydev)) { priv->line_interface = PHY_INTERFACE_MODE_1000BASEX; changed = true; } - break; - case PHY_INTERFACE_MODE_1000BASEX: - if (phydev->speed == SPEED_10000 && - mv2222_is_10g_capable(phydev)) { - priv->line_interface = PHY_INTERFACE_MODE_10GBASER; + if (mv2222_is_sgmii_capable(phydev)) { + priv->line_interface = PHY_INTERFACE_MODE_SGMII; changed = true; } break; + case PHY_INTERFACE_MODE_1000BASEX: case PHY_INTERFACE_MODE_SGMII: - ret = mv2222_set_sgmii_speed(phydev); - if (ret < 0) - return ret; + if (mv2222_is_10g_capable(phydev)) { + priv->line_interface = PHY_INTERFACE_MODE_10GBASER; + changed = true; + } break; default: @@ -310,6 +245,29 @@ static int mv2222_setup_forced(struct phy_device *phydev) return ret; } + return 0; +} + +static int mv2222_setup_forced(struct phy_device *phydev) +{ + struct mv2222_data *priv = phydev->priv; + int ret; + + if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) { + if (phydev->speed < SPEED_10000 && + phydev->speed != SPEED_UNKNOWN) { + ret = mv2222_swap_line_type(phydev); + if (ret < 0) + return ret; + } + } + + if (priv->line_interface == PHY_INTERFACE_MODE_SGMII) { + ret = mv2222_set_sgmii_speed(phydev); + if (ret < 0) + return ret; + } + return mv2222_disable_aneg(phydev); } @@ -323,17 +281,9 @@ static int mv2222_config_aneg(struct phy_device *phydev) return 0; if (phydev->autoneg == AUTONEG_DISABLE || - phydev->speed == SPEED_10000) + priv->line_interface == PHY_INTERFACE_MODE_10GBASER) return mv2222_setup_forced(phydev); - if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER && - mv2222_is_1gbx_capable(phydev)) { - priv->line_interface = PHY_INTERFACE_MODE_1000BASEX; - ret = mv2222_config_line(phydev); - if (ret < 0) - return ret; - } - adv = linkmode_adv_to_mii_adv_x(priv->supported, ETHTOOL_LINK_MODE_1000baseX_Full_BIT); @@ -367,6 +317,120 @@ static int mv2222_aneg_done(struct phy_device *phydev) return (ret & BMSR_ANEGCOMPLETE); } +/* Returns negative on error, 0 if link is down, 1 if link is up */ +static int mv2222_read_status_10g(struct phy_device *phydev) +{ + static int timeout; + int val, link = 0; + + val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_STAT1); + if (val < 0) + return val; + + if (val & MDIO_STAT1_LSTATUS) { + link = 1; + + /* 10GBASE-R do not support auto-negotiation */ + phydev->autoneg = AUTONEG_DISABLE; + phydev->speed = SPEED_10000; + phydev->duplex = DUPLEX_FULL; + } else { + if (phydev->autoneg == AUTONEG_ENABLE) { + timeout++; + + if (timeout > AUTONEG_TIMEOUT) { + timeout = 0; + + val = mv2222_swap_line_type(phydev); + if (val < 0) + return val; + + return mv2222_config_aneg(phydev); + } + } + } + + return link; +} + +/* Returns negative on error, 0 if link is down, 1 if link is up */ +static int mv2222_read_status_1g(struct phy_device *phydev) +{ + static int timeout; + int val, link = 0; + + val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_STAT); + if (val < 0) + return val; + + if ((phydev->autoneg == AUTONEG_ENABLE && + !(val & BMSR_ANEGCOMPLETE))) { + timeout++; + + if (timeout > AUTONEG_TIMEOUT) { + timeout = 0; + + val = mv2222_swap_line_type(phydev); + if (val < 0) + return val; + + return mv2222_config_aneg(phydev); + } + + return 0; + } + + if (!(val & BMSR_LSTATUS)) + return 0; + + link = 1; + + val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_1GBX_PHY_STAT); + if (val < 0) + return val; + + if (val & MV_1GBX_PHY_STAT_AN_RESOLVED) { + if (val & MV_1GBX_PHY_STAT_DUPLEX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + + if (val & MV_1GBX_PHY_STAT_SPEED1000) + phydev->speed = SPEED_1000; + else if (val & MV_1GBX_PHY_STAT_SPEED100) + phydev->speed = SPEED_100; + else + phydev->speed = SPEED_10; + } + + return link; +} + +static int mv2222_read_status(struct phy_device *phydev) +{ + struct mv2222_data *priv = phydev->priv; + int link; + + phydev->link = 0; + phydev->speed = SPEED_UNKNOWN; + phydev->duplex = DUPLEX_UNKNOWN; + + if (!priv->sfp_link) + return 0; + + if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) + link = mv2222_read_status_10g(phydev); + else + link = mv2222_read_status_1g(phydev); + + if (link < 0) + return link; + + phydev->link = link; + + return 0; +} + static int mv2222_resume(struct phy_device *phydev) { return mv2222_tx_enable(phydev); @@ -428,11 +492,7 @@ static int mv2222_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) return ret; if (mutex_trylock(&phydev->lock)) { - if (priv->line_interface == PHY_INTERFACE_MODE_10GBASER) - ret = mv2222_setup_forced(phydev); - else - ret = mv2222_config_aneg(phydev); - + ret = mv2222_config_aneg(phydev); mutex_unlock(&phydev->lock); } -- 2.26.3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
end of thread, other threads:[~2021-04-13 13:17 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-04-12 12:16 [PATCH net-next 0/2] net: phy: marvell-88x2222: a couple of improvements Ivan Bornyakov 2021-04-12 12:16 ` [PATCH net-next 1/2] net: phy: marvell-88x2222: check that link is operational Ivan Bornyakov 2021-04-12 23:32 ` Marek Behún 2021-04-13 7:13 ` Ivan Bornyakov 2021-04-13 13:07 ` Andrew Lunn 2021-04-12 23:40 ` Andrew Lunn 2021-04-13 7:19 ` Ivan Bornyakov 2021-04-13 9:23 ` Russell King - ARM Linux admin 2021-04-13 10:06 ` Ivan Bornyakov 2021-04-13 13:12 ` Andrew Lunn 2021-04-13 13:16 ` Russell King - ARM Linux admin 2021-04-12 12:17 ` [PATCH net-next 2/2] net: phy: marvell-88x2222: swap 1G/10G modes on autoneg Ivan Bornyakov
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.