[PATCH 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers

[PATCH 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers

[Sean Nyekjaer]

Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
accelerometers.
It will allow setting up scale/gain and reading x,y,z
axis.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
---
Changes:
 - Addresed comments from RFC.

 drivers/iio/accel/Kconfig           |  30 ++
 drivers/iio/accel/Makefile          |   3 +
 drivers/iio/accel/fxls8962af-core.c | 660 ++++++++++++++++++++++++++++
 drivers/iio/accel/fxls8962af-i2c.c  |  55 +++
 drivers/iio/accel/fxls8962af-spi.c  |  55 +++
 drivers/iio/accel/fxls8962af.h      |  20 +
 6 files changed, 823 insertions(+)
 create mode 100644 drivers/iio/accel/fxls8962af-core.c
 create mode 100644 drivers/iio/accel/fxls8962af-i2c.c
 create mode 100644 drivers/iio/accel/fxls8962af-spi.c
 create mode 100644 drivers/iio/accel/fxls8962af.h

diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
index 2e0c62c39155..50d3d6e86ac8 100644
--- a/drivers/iio/accel/Kconfig
+++ b/drivers/iio/accel/Kconfig
@@ -208,6 +208,36 @@ config DMARD10
 	  Choosing M will build the driver as a module. If so, the module
 	  will be called dmard10.
 
+config FXLS8962AF
+	tristate "NXP FXLS8962AF and similar Accelerometers Driver"
+	select REGMAP
+	help
+	  Say yes here to build support for the NXP 3-axis automotive
+	  accelerometer FXLS8962AF/FXLS8964AF.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called fxls8962af.
+
+config FXLS8962AF_I2C
+	tristate "NXP FXLS8962AF I2C transport"
+	depends on FXLS8962AF
+	depends on I2C
+	default FXLS8962AF
+	select REGMAP_I2C
+	help
+	  Say yes here to enable the NXP FXLS8962AF accelerometer
+	  I2C transport channel.
+
+config FXLS8962AF_SPI
+	tristate "NXP FXLS8962AF SPI transport"
+	depends on FXLS8962AF
+	depends on SPI
+	default FXLS8962AF
+	select REGMAP_SPI
+	help
+	  Say yes here to enable the NXP FXLS8962AF accelerometer
+	  SPI transport channel.
+
 config HID_SENSOR_ACCEL_3D
 	depends on HID_SENSOR_HUB
 	select IIO_BUFFER
diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
index 4f6c1ebe13b0..1b8c479c6f7c 100644
--- a/drivers/iio/accel/Makefile
+++ b/drivers/iio/accel/Makefile
@@ -25,6 +25,9 @@ obj-$(CONFIG_DA311)	+= da311.o
 obj-$(CONFIG_DMARD06)	+= dmard06.o
 obj-$(CONFIG_DMARD09)	+= dmard09.o
 obj-$(CONFIG_DMARD10)	+= dmard10.o
+obj-$(CONFIG_FXLS8962AF)	+= fxls8962af-core.o
+obj-$(CONFIG_FXLS8962AF_I2C)	+= fxls8962af-i2c.o
+obj-$(CONFIG_FXLS8962AF_SPI)	+= fxls8962af-spi.o
 obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
 obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
 obj-$(CONFIG_KXSD9)	+= kxsd9.o
diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
new file mode 100644
index 000000000000..3a60c1228055
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-core.c
@@ -0,0 +1,660 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 Connected Cars A/S
+ */
+
+#include <linux/module.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+
+#include "fxls8962af.h"
+
+#define FXLS8962AF_INT_STATUS			0x00
+#define FXLS8962AF_INT_STATUS_SRC_DRDY		BIT(7)
+#define FXLS8962AF_TEMP_OUT			0x01
+#define FXLS8962AF_VECM_LSB			0x02
+#define FXLS8962AF_OUT_X_LSB			0x04
+#define FXLS8962AF_OUT_Y_LSB			0x06
+#define FXLS8962AF_OUT_Z_LSB			0x08
+#define FXLS8962AF_BUF_STATUS			0x0b
+#define FXLS8962AF_BUF_X_LSB			0x0c
+#define FXLS8962AF_BUF_Y_LSB			0x0e
+#define FXLS8962AF_BUF_Z_LSB			0x10
+
+#define FXLS8962AF_PROD_REV			0x12
+#define FXLS8962AF_WHO_AM_I			0x13
+
+#define FXLS8962AF_SYS_MODE			0x14
+#define FXLS8962AF_SENS_CONFIG1			0x15
+#define FXLS8962AF_SENS_CONFIG1_ACTIVE		BIT(0)
+#define FXLS8962AF_SENS_CONFIG1_RST		BIT(7)
+#define FXLS8962AF_FSR_MASK			(BIT(2) | BIT(1))
+#define FXLS8962AF_FSR_SHIFT			1
+
+#define FXLS8962AF_SENS_CONFIG2			0x16
+#define FXLS8962AF_SENS_CONFIG3			0x17
+#define FXLS8962AF_SENS_CONFIG4			0x18
+#define FXLS8962AF_SENS_CONFIG5			0x19
+
+#define FXLS8962AF_WAKE_IDLE_LSB		0x1b
+#define FXLS8962AF_SLEEP_IDLE_LSB		0x1c
+#define FXLS8962AF_ASLP_COUNT_LSB		0x1e
+
+#define FXLS8962AF_INT_EN			0x20
+#define FXLS8962AF_INT_PIN_SEL			0x21
+
+#define FXLS8962AF_OFF_X			0x22
+#define FXLS8962AF_OFF_Y			0x23
+#define FXLS8962AF_OFF_Z			0x24
+
+#define FXLS8962AF_BUF_CONFIG1			0x26
+#define FXLS8962AF_BUF_CONFIG2			0x27
+
+#define FXLS8962AF_ORIENT_STATUS		0x28
+#define FXLS8962AF_ORIENT_CONFIG		0x29
+#define FXLS8962AF_ORIENT_DBCOUNT		0x2a
+#define FXLS8962AF_ORIENT_BF_ZCOMP		0x2b
+#define FXLS8962AF_ORIENT_THS_REG		0x2c
+
+#define FXLS8962AF_SDCD_INT_SRC1		0x2d
+#define FXLS8962AF_SDCD_INT_SRC2		0x2e
+#define FXLS8962AF_SDCD_CONFIG1			0x2f
+#define FXLS8962AF_SDCD_CONFIG2			0x30
+#define FXLS8962AF_SDCD_OT_DBCNT		0x31
+#define FXLS8962AF_SDCD_WT_DBCNT		0x32
+#define FXLS8962AF_SDCD_LTHS_LSB		0x33
+#define FXLS8962AF_SDCD_UTHS_LSB		0x35
+
+#define FXLS8962AF_SELF_TEST_CONFIG1		0x37
+#define FXLS8962AF_SELF_TEST_CONFIG2		0x38
+
+#define FXLS8962AF_MAX_REG			0x38
+
+#define FXLS8962AF_DEVICE_ID			0x62
+#define FXLS8964AF_DEVICE_ID			0x84
+
+#define FXLS8962AF_TEMP_CENTER_VAL		25
+
+#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS	2000
+
+#define FXLS8962AF_SCALE_TABLE_LEN		4
+
+static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
+	{0, IIO_G_TO_M_S_2(980000)}, {0, IIO_G_TO_M_S_2(1950000)},
+	{0, IIO_G_TO_M_S_2(3910000)}, {0, IIO_G_TO_M_S_2(7810000)},
+};
+
+struct fxls8962af_chip_info {
+	u8 chip_id;
+	const char *name;
+	const struct iio_chan_spec *channels;
+	int num_channels;
+};
+
+struct fxls8962af_data {
+	struct regmap *regmap;
+	struct mutex lock;
+	const struct fxls8962af_chip_info *chip_info;
+	struct regulator *vdd_reg;
+	struct iio_mount_matrix orientation;
+};
+
+const struct regmap_config fxls8962af_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = FXLS8962AF_MAX_REG,
+};
+EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
+
+enum {
+	fxls8962af_idx_x,
+	fxls8962af_idx_y,
+	fxls8962af_idx_z,
+	fxls8962af_idx_ts,
+};
+
+static int fxls8962af_drdy(struct fxls8962af_data *data)
+{
+	int tries = 150, ret;
+	unsigned int reg;
+	struct device *dev = regmap_get_device(data->regmap);
+
+	while (tries-- > 0) {
+		ret = regmap_read(data->regmap, FXLS8962AF_INT_STATUS, &reg);
+		if (ret < 0)
+			return ret;
+
+		if ((reg & FXLS8962AF_INT_STATUS_SRC_DRDY) ==
+		    FXLS8962AF_INT_STATUS_SRC_DRDY)
+			return 0;
+
+		msleep(20);
+	}
+
+	dev_err(dev, "data not ready\n");
+
+	return -EIO;
+}
+
+static int fxls8962af_set_power_state(struct fxls8962af_data *data, bool on)
+{
+#ifdef CONFIG_PM
+	struct device *dev = regmap_get_device(data->regmap);
+	int ret;
+
+	if (on) {
+		ret = pm_runtime_get_sync(dev);
+	} else {
+		pm_runtime_mark_last_busy(dev);
+		ret = pm_runtime_put_autosuspend(dev);
+	}
+
+	if (ret < 0) {
+		dev_err(dev, "failed to change power state to %d\n", on);
+		if (on)
+			pm_runtime_put_noidle(dev);
+
+		return ret;
+	}
+#endif
+
+	return 0;
+}
+
+static int fxls8962af_get_temp(struct fxls8962af_data *data, int *val)
+{
+	struct device *dev = regmap_get_device(data->regmap);
+	int ret;
+	unsigned int value;
+
+	mutex_lock(&data->lock);
+
+	ret = fxls8962af_drdy(data);
+	if (ret < 0) {
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = fxls8962af_set_power_state(data, true);
+	if (ret) {
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = regmap_read(data->regmap, FXLS8962AF_TEMP_OUT, &value);
+	if (ret < 0) {
+		dev_err(dev, "Error reading reg_temp\n");
+		fxls8962af_set_power_state(data, false);
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = fxls8962af_set_power_state(data, false);
+
+	mutex_unlock(&data->lock);
+
+	*val = sign_extend32(value, 7);
+
+	if (ret < 0)
+		return ret;
+
+	return IIO_VAL_INT;
+}
+
+static int fxls8962af_get_axis(struct fxls8962af_data *data,
+			       struct iio_chan_spec const *chan, int *val)
+{
+	struct device *dev = regmap_get_device(data->regmap);
+	int ret;
+	__le16 raw_val;
+
+	mutex_lock(&data->lock);
+
+	ret = fxls8962af_drdy(data);
+	if (ret < 0) {
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = fxls8962af_set_power_state(data, true);
+	if (ret) {
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = regmap_bulk_read(data->regmap, chan->address,
+			       &raw_val, sizeof(raw_val));
+	if (ret < 0) {
+		dev_err(dev, "failed to read axes\n");
+		fxls8962af_set_power_state(data, false);
+		mutex_unlock(&data->lock);
+		return ret;
+	}
+
+	ret = fxls8962af_set_power_state(data, false);
+
+	mutex_unlock(&data->lock);
+	*val = sign_extend32(le16_to_cpu(raw_val),
+			     chan->scan_type.realbits - 1);
+
+	if (ret < 0)
+		return ret;
+
+	return IIO_VAL_INT;
+}
+
+static int fxls8962af_read_avail(struct iio_dev *indio_dev,
+				 struct iio_chan_spec const *chan,
+				 const int **vals, int *type, int *length,
+				 long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		*type = IIO_VAL_INT_PLUS_NANO;
+		*vals = (int *)fxls8962af_scale_table;
+		*length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
+					struct iio_chan_spec const *chan,
+					long mask)
+{
+	return IIO_VAL_INT_PLUS_NANO;
+}
+
+static int fxls8962af_standby(struct fxls8962af_data *data)
+{
+	return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+				  FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
+}
+
+static int fxls8962af_active(struct fxls8962af_data *data)
+{
+	return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+				  FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
+}
+
+static int fxls8962af_is_active(struct fxls8962af_data *data)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
+	if (ret < 0)
+		return ret;
+
+	return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
+}
+
+static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
+				    u8 mask, u8 val)
+{
+	int ret;
+	int is_active;
+
+	mutex_lock(&data->lock);
+
+	is_active = fxls8962af_is_active(data);
+	if (is_active < 0) {
+		ret = is_active;
+		goto fail;
+	}
+
+	/* config can only be changed when in standby */
+	if (is_active > 0) {
+		ret = fxls8962af_standby(data);
+		if (ret < 0)
+			goto fail;
+	}
+
+	ret = regmap_update_bits(data->regmap, reg, mask, val);
+	if (ret < 0)
+		goto fail;
+
+	if (is_active > 0) {
+		ret = fxls8962af_active(data);
+		if (ret < 0)
+			goto fail;
+	}
+
+	ret = 0;
+ fail:
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
+		if (scale == fxls8962af_scale_table[i][1])
+			break;
+
+	if (i == ARRAY_SIZE(fxls8962af_scale_table))
+		return -EINVAL;
+
+	return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
+					FXLS8962AF_FSR_MASK,
+					i << FXLS8962AF_FSR_SHIFT);
+}
+
+static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
+					       int *val)
+{
+	int ret;
+	unsigned int reg;
+	u8 range_idx;
+
+	ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
+	if (ret < 0)
+		return ret;
+
+	range_idx = (reg & FXLS8962AF_FSR_MASK) >> FXLS8962AF_FSR_SHIFT;
+
+	*val = fxls8962af_scale_table[range_idx][1];
+
+	return IIO_VAL_INT_PLUS_NANO;
+}
+
+static int fxls8962af_read_raw(struct iio_dev *indio_dev,
+			       struct iio_chan_spec const *chan,
+			       int *val, int *val2, long mask)
+{
+	struct fxls8962af_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = iio_device_claim_direct_mode(indio_dev);
+		if (ret)
+			return ret;
+
+		switch (chan->type) {
+		case IIO_TEMP:
+			ret = fxls8962af_get_temp(data, val);
+			break;
+		case IIO_ACCEL:
+			ret = fxls8962af_get_axis(data, chan, val);
+			break;
+		default:
+			ret = -EINVAL;
+		}
+
+		iio_device_release_direct_mode(indio_dev);
+		return ret;
+	case IIO_CHAN_INFO_OFFSET:
+		if (chan->type == IIO_TEMP) {
+			*val = FXLS8962AF_TEMP_CENTER_VAL;
+			return IIO_VAL_INT;
+		} else {
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_SCALE:
+		*val = 0;
+		ret = fxls8962af_read_full_scale(data, val2);
+		return ret;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	return -EINVAL;
+}
+
+static int fxls8962af_write_raw(struct iio_dev *indio_dev,
+				struct iio_chan_spec const *chan,
+				int val, int val2, long mask)
+{
+	struct fxls8962af_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		if(val != 0)
+			return -EINVAL;
+
+		ret = fxls8962af_set_full_scale(data, val2);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	iio_device_release_direct_mode(indio_dev);
+	return ret;
+}
+
+#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
+	.type = IIO_ACCEL, \
+	.address = reg, \
+	.modified = 1, \
+	.channel2 = IIO_MOD_##axis, \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
+	.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
+	.scan_index = idx, \
+	.scan_type = { \
+		.sign = 's', \
+		.realbits = 12, \
+		.storagebits = 16, \
+		.shift = 4, \
+		.endianness = IIO_BE, \
+	}, \
+}
+
+#define FXLS8962AF_TEMP_CHANNEL { \
+	.type = IIO_TEMP, \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+			      BIT(IIO_CHAN_INFO_OFFSET),\
+	.scan_index = -1, \
+	.scan_type = { \
+		.sign = 's', \
+		.realbits = 8, \
+		.storagebits = 16, \
+	}, \
+}
+
+static const struct iio_chan_spec fxls8962af_channels[] = {
+	FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
+	FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
+	FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
+	IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
+	FXLS8962AF_TEMP_CHANNEL,
+};
+
+static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
+	[fxls8962af] = {
+		.chip_id = FXLS8962AF_DEVICE_ID,
+		.name = "fxls8962af",
+		.channels = fxls8962af_channels,
+		.num_channels = ARRAY_SIZE(fxls8962af_channels),
+	},
+	[fxls8964af] = {
+		.chip_id = FXLS8964AF_DEVICE_ID,
+		.name = "fxls8964af",
+		.channels = fxls8962af_channels,
+		.num_channels = ARRAY_SIZE(fxls8962af_channels),
+	}
+};
+
+static const struct iio_info fxls8962af_info = {
+	.read_raw = &fxls8962af_read_raw,
+	.write_raw = &fxls8962af_write_raw,
+	.write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
+	.read_avail = fxls8962af_read_avail,
+};
+
+static int fxls8962af_reset(struct fxls8962af_data *data)
+{
+	int i, ret;
+	unsigned int reg;
+
+	ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+				 FXLS8962AF_SENS_CONFIG1_RST,
+				 FXLS8962AF_SENS_CONFIG1_RST);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < 10; i++) {
+		usleep_range(100, 200);
+		ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
+		if (ret == -EIO)
+			continue;	/* I2C comm reset */
+		if (ret < 0)
+			return ret;
+		if (!(reg & FXLS8962AF_SENS_CONFIG1_RST))
+			return 0;
+	}
+
+	return -ETIMEDOUT;
+}
+
+static void fxls8962af_regulator_disable(void *data_ptr)
+{
+	struct fxls8962af_data *data = data_ptr;
+
+	regulator_disable(data->vdd_reg);
+}
+
+static void fxls8962af_pm_disable(void *dev_ptr)
+{
+	struct device *dev = dev_ptr;
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_put_noidle(dev);
+
+	fxls8962af_standby(iio_priv(indio_dev));
+}
+
+int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
+{
+	struct fxls8962af_data *data;
+	struct iio_dev *indio_dev;
+	unsigned int reg;
+	int ret, i;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	dev_set_drvdata(dev, indio_dev);
+	mutex_init(&data->lock);
+	data->regmap = regmap;
+
+	ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation);
+	if (ret)
+		return ret;
+
+	data->vdd_reg = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(data->vdd_reg))
+		return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
+				     "Failed to get vdd regulator\n");
+
+	ret = regulator_enable(data->vdd_reg);
+	if (ret) {
+		dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
+		return ret;
+	}
+
+	ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, &reg);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
+		if (fxls_chip_info_table[i].chip_id == reg) {
+			data->chip_info = &fxls_chip_info_table[i];
+			break;
+		}
+	}
+
+	indio_dev->channels = data->chip_info->channels;
+	indio_dev->num_channels = data->chip_info->num_channels;
+	indio_dev->name = data->chip_info->name;
+	indio_dev->info = &fxls8962af_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	ret = fxls8962af_reset(data);
+	if (ret < 0)
+		return ret;
+
+	ret = pm_runtime_set_active(dev);
+	if (ret < 0)
+		return ret;
+
+	pm_runtime_enable(dev);
+	pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(dev);
+
+	ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
+	if (ret)
+		return ret;
+
+
+	return devm_iio_device_register(dev, indio_dev);
+
+}
+EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
+
+#ifdef CONFIG_PM
+static int fxls8962af_runtime_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct fxls8962af_data *data = iio_priv(indio_dev);
+	int ret;
+
+	mutex_lock(&data->lock);
+	ret = fxls8962af_standby(data);
+	mutex_unlock(&data->lock);
+	if (ret < 0) {
+		dev_err(dev, "powering off device failed\n");
+		return -EAGAIN;
+	}
+
+	return 0;
+}
+
+static int fxls8962af_runtime_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct fxls8962af_data *data = iio_priv(indio_dev);
+	int ret;
+
+	ret = fxls8962af_active(data);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+#endif
+
+const struct dev_pm_ops fxls8962af_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
+			   fxls8962af_runtime_resume, NULL)
+};
+EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af-i2c.c b/drivers/iio/accel/fxls8962af-i2c.c
new file mode 100644
index 000000000000..c04705a33642
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-i2c.c
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 Connected Cars A/S
+ */
+
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "fxls8962af.h"
+
+static int fxls8962af_probe(struct i2c_client *client)
+{
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
+	if (IS_ERR(regmap)) {
+		dev_err(&client->dev, "Failed to initialize i2c regmap\n");
+		return PTR_ERR(regmap);
+	}
+
+	return fxls8962af_core_probe(&client->dev, regmap, client->irq);
+}
+
+static const struct i2c_device_id fxls8962af_id[] = {
+	{"fxls8962af", fxls8962af},
+	{"fxls8964af", fxls8964af},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, fxls8962af_id);
+
+static const struct of_device_id fxls8962af_of_match[] = {
+	{.compatible = "nxp,fxls8962af"},
+	{.compatible = "nxp,fxls8964af"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, fxls8962af_of_match);
+
+static struct i2c_driver fxls8962af_driver = {
+	.driver = {
+		   .name = "fxls8962af_i2c",
+		   .of_match_table = fxls8962af_of_match,
+		   .pm = &fxls8962af_pm_ops,
+		   },
+	.probe_new = fxls8962af_probe,
+	.id_table = fxls8962af_id,
+};
+
+module_i2c_driver(fxls8962af_driver);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af-spi.c b/drivers/iio/accel/fxls8962af-spi.c
new file mode 100644
index 000000000000..31a3183e0049
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-spi.c
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 Connected Cars A/S
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+
+#include "fxls8962af.h"
+
+static int fxls8962af_probe(struct spi_device *spi)
+{
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
+	if (IS_ERR(regmap)) {
+		dev_err(&spi->dev, "Failed to initialize spi regmap\n");
+		return PTR_ERR(regmap);
+	}
+
+	return fxls8962af_core_probe(&spi->dev, regmap, spi->irq);
+}
+
+static const struct of_device_id fxls8962af_spi_of_match[] = {
+	{.compatible = "nxp,fxls8962af"},
+	{.compatible = "nxp,fxls8964af"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, fxls8962af_spi_of_match);
+
+static const struct spi_device_id fxls8962af_spi_id_table[] = {
+	{"fxls8962af", fxls8962af},
+	{"fxls8964af", fxls8964af},
+	{},
+};
+MODULE_DEVICE_TABLE(spi, fxls8962af_spi_id_table);
+
+static struct spi_driver fxls8962af_driver = {
+	.driver = {
+		   .name = "fxls8962af_spi",
+		   .pm = &fxls8962af_pm_ops,
+		   .of_match_table = fxls8962af_spi_of_match,
+		   },
+	.probe = fxls8962af_probe,
+	.id_table = fxls8962af_spi_id_table,
+};
+
+module_spi_driver(fxls8962af_driver);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af.h b/drivers/iio/accel/fxls8962af.h
new file mode 100644
index 000000000000..e06bfa4188a3
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2021 Connected Cars A/S
+ */
+#ifndef _FXLS8962AF_H_
+#define _FXLS8962AF_H_
+
+struct regmap;
+
+enum {
+	fxls8962af,
+	fxls8964af,
+};
+
+int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq);
+int fxls8962af_core_remove(struct device *dev);
+extern const struct dev_pm_ops fxls8962af_pm_ops;
+extern const struct regmap_config fxls8962af_regmap_conf;
+
+#endif				/* _FXLS8962AF_H_ */
-- 
2.31.0

[PATCH 2/2] dt-bindings: iio: accel: fxls8962af: add bindings

[Sean Nyekjaer]

Add devicetree binding for the NXP FXLS8962AF/FXLS8962AF
accelerometer sensor.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
---
Changes:
 - Checked with 'make DT_CHECKER_FLAGS=-m dt_binding_check'

 .../bindings/iio/accel/nxp,fxls8962af.yaml    | 73 +++++++++++++++++++
 1 file changed, 73 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml

diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
new file mode 100644
index 000000000000..57322ec8df81
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/accel/nxp,fxls8962af.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP FXLS8962AF/FXLS8964AF Accelerometer driver
+
+maintainers:
+  - Sean Nyekjaer <sean@geanix.com>
+
+description: |
+  NXP FXLS8962AF/FXLS8964AF Accelerometer driver that supports
+  SPI and I2C interface.
+    https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
+    https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
+
+properties:
+  compatible:
+    enum:
+      - nxp,fxls8962af
+      - nxp,fxls8964af
+
+  reg:
+    maxItems: 1
+
+  vdd-supply:
+    description: phandle to the regulator that provides power to the accelerometer
+
+  spi-max-frequency: true
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* Example for a I2C device node */
+        accelerometer@62 {
+            compatible = "nxp,fxls8962af";
+            reg = <0x62>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+        };
+    };
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* Example for a SPI device node */
+        accelerometer@0 {
+            compatible = "nxp,fxls8962af";
+            reg = <0>;
+            spi-max-frequency = <4000000>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+        };
+    };
-- 
2.31.0

Re: [PATCH 2/2] dt-bindings: iio: accel: fxls8962af: add bindings

[Jonathan Cameron]

On Fri, 16 Apr 2021 11:30:39 +0200
Sean Nyekjaer <sean@geanix.com> wrote:

> Add devicetree binding for the NXP FXLS8962AF/FXLS8962AF
> accelerometer sensor.
> 
> Signed-off-by: Sean Nyekjaer <sean@geanix.com>
> ---
> Changes:
>  - Checked with 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> 
>  .../bindings/iio/accel/nxp,fxls8962af.yaml    | 73 +++++++++++++++++++
>  1 file changed, 73 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
> new file mode 100644
> index 000000000000..57322ec8df81
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
> @@ -0,0 +1,73 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/accel/nxp,fxls8962af.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP FXLS8962AF/FXLS8964AF Accelerometer driver
> +
> +maintainers:
> +  - Sean Nyekjaer <sean@geanix.com>
> +
> +description: |
> +  NXP FXLS8962AF/FXLS8964AF Accelerometer driver that supports
> +  SPI and I2C interface.
> +    https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> +    https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - nxp,fxls8962af
> +      - nxp,fxls8964af
> +
> +  reg:
> +    maxItems: 1
> +
> +  vdd-supply:
> +    description: phandle to the regulator that provides power to the accelerometer
> +
> +  spi-max-frequency: true
> +
> +  interrupts:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts

It's rare to actually 'require' interrupts for an accelerometer.
We tend to rapidly find someone has a board where the interrupt isn't wired.
Given it's usually fairly easy to implement the no interrupt case by
just having an alternative iio_info structure in the driver it would be
good to have that from the start if possible.

> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    i2c0 {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        /* Example for a I2C device node */
> +        accelerometer@62 {
> +            compatible = "nxp,fxls8962af";
> +            reg = <0x62>;
> +            interrupt-parent = <&gpio0>;
> +            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +        };
> +    };
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    spi0 {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        /* Example for a SPI device node */
> +        accelerometer@0 {
> +            compatible = "nxp,fxls8962af";
> +            reg = <0>;
> +            spi-max-frequency = <4000000>;
> +            interrupt-parent = <&gpio0>;
> +            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +        };
> +    };

Re: [PATCH 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers

[Andy Shevchenko]

On Fri, Apr 16, 2021 at 1:28 PM Sean Nyekjaer <sean@geanix.com> wrote:
>
> Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
> accelerometers.
> It will allow setting up scale/gain and reading x,y,z
> axis.

Do you have a link to the data sheet? Can you add it as Datasheet: tag?

> Signed-off-by: Sean Nyekjaer <sean@geanix.com>

...

> +config FXLS8962AF
> +       tristate "NXP FXLS8962AF and similar Accelerometers Driver"

I guess this can be hidden.

> +       select REGMAP
> +       help
> +         Say yes here to build support for the NXP 3-axis automotive
> +         accelerometer FXLS8962AF/FXLS8964AF.
> +
> +         To compile this driver as a module, choose M here: the module
> +         will be called fxls8962af.
> +
> +config FXLS8962AF_I2C
> +       tristate "NXP FXLS8962AF I2C transport"

> +       depends on FXLS8962AF

Why not select?

> +       depends on I2C

> +       default FXLS8962AF

And drop this.

> +       select REGMAP_I2C
> +       help
> +         Say yes here to enable the NXP FXLS8962AF accelerometer
> +         I2C transport channel.

Missed module name.

> +config FXLS8962AF_SPI
> +       tristate "NXP FXLS8962AF SPI transport"
> +       depends on FXLS8962AF
> +       depends on SPI
> +       default FXLS8962AF
> +       select REGMAP_SPI
> +       help
> +         Say yes here to enable the NXP FXLS8962AF accelerometer
> +         SPI transport channel.

Three comments as per I2C case.

...

> +/*
> + * Copyright 2021 Connected Cars A/S
> + */

One line

...

> +#include <linux/module.h>


Missed bits.h

> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>

Can you split it to a separate group to go...

> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/regmap.h>

...here?

> +#include "fxls8962af.h"

...

> +#define FXLS8962AF_FSR_MASK                    (BIT(2) | BIT(1))

GENMASK() ?

...

> +#define FXLS8962AF_TEMP_CENTER_VAL             25

Is it decimal one or bit based? I mean the maximum is 50 or is it a
bit field which represents raw value?

...

> +struct fxls8962af_chip_info {
> +       u8 chip_id;

You may save some memory if you move this at the end of the structure.

> +       const char *name;
> +       const struct iio_chan_spec *channels;
> +       int num_channels;
> +};

...

> +struct fxls8962af_data {
> +       struct regmap *regmap;
> +       struct mutex lock;

So, you are  using the regmap lock, what is this for? The golden rule
one _must_ describe locks (their purposes).

> +       const struct fxls8962af_chip_info *chip_info;
> +       struct regulator *vdd_reg;
> +       struct iio_mount_matrix orientation;
> +};

...

> +static int fxls8962af_drdy(struct fxls8962af_data *data)
> +{
> +       int tries = 150, ret;
> +       unsigned int reg;
> +       struct device *dev = regmap_get_device(data->regmap);

Try to keep reversed xmas tree order in definition block(s).

> +       while (tries-- > 0) {
> +               ret = regmap_read(data->regmap, FXLS8962AF_INT_STATUS, &reg);
> +               if (ret < 0)
> +                       return ret;
> +
> +               if ((reg & FXLS8962AF_INT_STATUS_SRC_DRDY) ==
> +                   FXLS8962AF_INT_STATUS_SRC_DRDY)
> +                       return 0;
> +
> +               msleep(20);
> +       }

Entire loop is repetition of regmap_read_poll_timeout().

> +       dev_err(dev, "data not ready\n");
> +
> +       return -EIO;
> +}
> +
> +static int fxls8962af_set_power_state(struct fxls8962af_data *data, bool on)
> +{

> +#ifdef CONFIG_PM

Why?

> +       struct device *dev = regmap_get_device(data->regmap);
> +       int ret;
> +
> +       if (on) {
> +               ret = pm_runtime_get_sync(dev);
> +       } else {
> +               pm_runtime_mark_last_busy(dev);
> +               ret = pm_runtime_put_autosuspend(dev);
> +       }
> +
> +       if (ret < 0) {
> +               dev_err(dev, "failed to change power state to %d\n", on);
> +               if (on)
> +                       pm_runtime_put_noidle(dev);
> +
> +               return ret;
> +       }

Untangle this. You may do on and off cases separately for better understanding.

> +#endif
> +
> +       return 0;
> +}

...

> +       if (ret < 0) {
> +               mutex_unlock(&data->lock);
> +               return ret;
> +       }

goto variant in all similar places will save you a lot of lines

goto out_unlock;

...

out_unlock: // or err_unlock if it's only for error path.
  mutex_unlock(...);
  return ret;

...

> +       *val = sign_extend32(le16_to_cpu(raw_val),
> +                            chan->scan_type.realbits - 1);

One line?

...

> +       mutex_lock(&data->lock);
> +
> +       is_active = fxls8962af_is_active(data);
> +       if (is_active < 0) {
> +               ret = is_active;
> +               goto fail;
> +       }

Why not

ret = ...;
if (ret < 0)
  goto fail;

... = ret;

?

Also note inconsistency here with goto style and there where you open
coded error paths.

...

> + fail:

err_unlock:

Labels should be descriptive.

> +       mutex_unlock(&data->lock);

...

> +               switch (chan->type) {
> +               case IIO_TEMP:
> +                       ret = fxls8962af_get_temp(data, val);
> +                       break;
> +               case IIO_ACCEL:
> +                       ret = fxls8962af_get_axis(data, chan, val);
> +                       break;
> +               default:
> +                       ret = -EINVAL;

break is missed.

> +               }

...

> +       case IIO_CHAN_INFO_OFFSET:
> +               if (chan->type == IIO_TEMP) {
> +                       *val = FXLS8962AF_TEMP_CENTER_VAL;
> +                       return IIO_VAL_INT;


> +               } else {

Redundant 'else'

> +                       return -EINVAL;
> +               }

You may rather refactor this to be like

if (type != ...)
  return -EINVAL;

...


> +               ret = fxls8962af_read_full_scale(data, val2);
> +               return ret;

Why not return directly?

> +       default:
> +               ret = -EINVAL;
> +               break;

Ditto.

> +       }

> +       return -EINVAL;

Isn't it a dead code?

...

> +static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
> +       [fxls8962af] = {
> +               .chip_id = FXLS8962AF_DEVICE_ID,
> +               .name = "fxls8962af",
> +               .channels = fxls8962af_channels,
> +               .num_channels = ARRAY_SIZE(fxls8962af_channels),
> +       },
> +       [fxls8964af] = {
> +               .chip_id = FXLS8964AF_DEVICE_ID,
> +               .name = "fxls8964af",
> +               .channels = fxls8962af_channels,
> +               .num_channels = ARRAY_SIZE(fxls8962af_channels),


> +       }

Leave the comma here as well.

> +};

...

> +       for (i = 0; i < 10; i++) {
> +               usleep_range(100, 200);
> +               ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
> +               if (ret == -EIO)
> +                       continue;       /* I2C comm reset */
> +               if (ret < 0)
> +                       return ret;
> +               if (!(reg & FXLS8962AF_SENS_CONFIG1_RST))
> +                       return 0;
> +       }
> +
> +       return -ETIMEDOUT;

Consider to adapt to regmap_read_poll_timeout().

> +}

...

> +       ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
> +       if (ret)
> +               return ret;
> +
> +

Too many blank lines.

> +       return devm_iio_device_register(dev, indio_dev);
> +

Ditto.

...

> +#ifdef CONFIG_PM

No, please use __maybe_unused attribute.

> +static int fxls8962af_runtime_suspend(struct device *dev)
> +{
> +       struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +       struct fxls8962af_data *data = iio_priv(indio_dev);
> +       int ret;
> +
> +       mutex_lock(&data->lock);
> +       ret = fxls8962af_standby(data);
> +       mutex_unlock(&data->lock);
> +       if (ret < 0) {
> +               dev_err(dev, "powering off device failed\n");

> +               return -EAGAIN;

Why error code shadowing?

> +       }
> +
> +       return 0;
> +}
> +
> +static int fxls8962af_runtime_resume(struct device *dev)
> +{
> +       struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +       struct fxls8962af_data *data = iio_priv(indio_dev);
> +       int ret;
> +
> +       ret = fxls8962af_active(data);
> +       if (ret < 0)
> +               return ret;
> +
> +       return 0;
> +}
> +#endif

...

> +/*
> + * Copyright 2021 Connected Cars A/S
> + */

One line.

...

> +#include <linux/device.h>

Shouldn't this be dev_printk.h?

> +#include <linux/mod_devicetable.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>

...

> +/*
> + * Copyright 2021 Connected Cars A/S
> + */

One line?

...

> +#include <linux/kernel.h>

What for?

...

> +static const struct of_device_id fxls8962af_spi_of_match[] = {
> +       {.compatible = "nxp,fxls8962af"},
> +       {.compatible = "nxp,fxls8964af"},

> +       {},

Comma is not needed for terminator lines.

> +};

...

> +static const struct spi_device_id fxls8962af_spi_id_table[] = {
> +       {"fxls8962af", fxls8962af},
> +       {"fxls8964af", fxls8964af},
> +       {},

Ditto.

> +};

...

> +/*
> + * Copyright 2021 Connected Cars A/S
> + */

One line.

...

> +struct regmap;

struct device;

is missed.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers

[Jonathan Cameron]

On Fri, 16 Apr 2021 11:30:38 +0200
Sean Nyekjaer <sean@geanix.com> wrote:

> Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
> accelerometers.
> It will allow setting up scale/gain and reading x,y,z
> axis.
> 
> Signed-off-by: Sean Nyekjaer <sean@geanix.com>

I'll probably mirror some of what Andy said and may well find nothing
more than he has :)  I took a quick glance, so didn't comment on what
I was sure Andy had mentioned.

Anyhow comments inline.

Thanks,

Jonathan

> ---
> Changes:
>  - Addresed comments from RFC.
> 
>  drivers/iio/accel/Kconfig           |  30 ++
>  drivers/iio/accel/Makefile          |   3 +
>  drivers/iio/accel/fxls8962af-core.c | 660 ++++++++++++++++++++++++++++
>  drivers/iio/accel/fxls8962af-i2c.c  |  55 +++
>  drivers/iio/accel/fxls8962af-spi.c  |  55 +++
>  drivers/iio/accel/fxls8962af.h      |  20 +
>  6 files changed, 823 insertions(+)
>  create mode 100644 drivers/iio/accel/fxls8962af-core.c
>  create mode 100644 drivers/iio/accel/fxls8962af-i2c.c
>  create mode 100644 drivers/iio/accel/fxls8962af-spi.c
>  create mode 100644 drivers/iio/accel/fxls8962af.h
> 
> diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
> index 2e0c62c39155..50d3d6e86ac8 100644
> --- a/drivers/iio/accel/Kconfig
> +++ b/drivers/iio/accel/Kconfig
> @@ -208,6 +208,36 @@ config DMARD10
>  	  Choosing M will build the driver as a module. If so, the module
>  	  will be called dmard10.
>  
> +config FXLS8962AF
> +	tristate "NXP FXLS8962AF and similar Accelerometers Driver"

Hide this from menu by removing the title above.

> +	select REGMAP
> +	help
> +	  Say yes here to build support for the NXP 3-axis automotive
> +	  accelerometer FXLS8962AF/FXLS8964AF.
> +
> +	  To compile this driver as a module, choose M here: the module
> +	  will be called fxls8962af.
> +
> +config FXLS8962AF_I2C
> +	tristate "NXP FXLS8962AF I2C transport"
> +	depends on FXLS8962AF
> +	depends on I2C
> +	default FXLS8962AF
> +	select REGMAP_I2C
> +	help
> +	  Say yes here to enable the NXP FXLS8962AF accelerometer
> +	  I2C transport channel.
> +
> +config FXLS8962AF_SPI
> +	tristate "NXP FXLS8962AF SPI transport"
> +	depends on FXLS8962AF
> +	depends on SPI
> +	default FXLS8962AF
> +	select REGMAP_SPI
> +	help
> +	  Say yes here to enable the NXP FXLS8962AF accelerometer
> +	  SPI transport channel.
> +
>  config HID_SENSOR_ACCEL_3D
>  	depends on HID_SENSOR_HUB
>  	select IIO_BUFFER
> diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
> index 4f6c1ebe13b0..1b8c479c6f7c 100644
> --- a/drivers/iio/accel/Makefile
> +++ b/drivers/iio/accel/Makefile
> @@ -25,6 +25,9 @@ obj-$(CONFIG_DA311)	+= da311.o
>  obj-$(CONFIG_DMARD06)	+= dmard06.o
>  obj-$(CONFIG_DMARD09)	+= dmard09.o
>  obj-$(CONFIG_DMARD10)	+= dmard10.o
> +obj-$(CONFIG_FXLS8962AF)	+= fxls8962af-core.o
> +obj-$(CONFIG_FXLS8962AF_I2C)	+= fxls8962af-i2c.o
> +obj-$(CONFIG_FXLS8962AF_SPI)	+= fxls8962af-spi.o
>  obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
>  obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
>  obj-$(CONFIG_KXSD9)	+= kxsd9.o
> diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
> new file mode 100644
> index 000000000000..3a60c1228055
> --- /dev/null
> +++ b/drivers/iio/accel/fxls8962af-core.c
> @@ -0,0 +1,660 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2021 Connected Cars A/S
> + */
> +
> +#include <linux/module.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/regmap.h>
> +
> +#include "fxls8962af.h"
> +
> +#define FXLS8962AF_INT_STATUS			0x00
> +#define FXLS8962AF_INT_STATUS_SRC_DRDY		BIT(7)
> +#define FXLS8962AF_TEMP_OUT			0x01
> +#define FXLS8962AF_VECM_LSB			0x02
> +#define FXLS8962AF_OUT_X_LSB			0x04
> +#define FXLS8962AF_OUT_Y_LSB			0x06
> +#define FXLS8962AF_OUT_Z_LSB			0x08
> +#define FXLS8962AF_BUF_STATUS			0x0b
> +#define FXLS8962AF_BUF_X_LSB			0x0c
> +#define FXLS8962AF_BUF_Y_LSB			0x0e
> +#define FXLS8962AF_BUF_Z_LSB			0x10
> +
> +#define FXLS8962AF_PROD_REV			0x12
> +#define FXLS8962AF_WHO_AM_I			0x13
> +
> +#define FXLS8962AF_SYS_MODE			0x14
> +#define FXLS8962AF_SENS_CONFIG1			0x15
> +#define FXLS8962AF_SENS_CONFIG1_ACTIVE		BIT(0)
> +#define FXLS8962AF_SENS_CONFIG1_RST		BIT(7)
> +#define FXLS8962AF_FSR_MASK			(BIT(2) | BIT(1))

GENMASK(2,1)

It can be good to use naming to indicate 'containment' of fields.
Here it's not obvious which register FSR is in.

> +#define FXLS8962AF_FSR_SHIFT			1

Use FIELD_PREP and FIELD_GET so you don't need to define mask and shift
separately.

> +
> +#define FXLS8962AF_SENS_CONFIG2			0x16
> +#define FXLS8962AF_SENS_CONFIG3			0x17
> +#define FXLS8962AF_SENS_CONFIG4			0x18
> +#define FXLS8962AF_SENS_CONFIG5			0x19
> +
> +#define FXLS8962AF_WAKE_IDLE_LSB		0x1b
> +#define FXLS8962AF_SLEEP_IDLE_LSB		0x1c
> +#define FXLS8962AF_ASLP_COUNT_LSB		0x1e
> +
> +#define FXLS8962AF_INT_EN			0x20
> +#define FXLS8962AF_INT_PIN_SEL			0x21
> +
> +#define FXLS8962AF_OFF_X			0x22
> +#define FXLS8962AF_OFF_Y			0x23
> +#define FXLS8962AF_OFF_Z			0x24
> +
> +#define FXLS8962AF_BUF_CONFIG1			0x26
> +#define FXLS8962AF_BUF_CONFIG2			0x27
> +
> +#define FXLS8962AF_ORIENT_STATUS		0x28
> +#define FXLS8962AF_ORIENT_CONFIG		0x29
> +#define FXLS8962AF_ORIENT_DBCOUNT		0x2a
> +#define FXLS8962AF_ORIENT_BF_ZCOMP		0x2b
> +#define FXLS8962AF_ORIENT_THS_REG		0x2c
> +
> +#define FXLS8962AF_SDCD_INT_SRC1		0x2d
> +#define FXLS8962AF_SDCD_INT_SRC2		0x2e
> +#define FXLS8962AF_SDCD_CONFIG1			0x2f
> +#define FXLS8962AF_SDCD_CONFIG2			0x30
> +#define FXLS8962AF_SDCD_OT_DBCNT		0x31
> +#define FXLS8962AF_SDCD_WT_DBCNT		0x32
> +#define FXLS8962AF_SDCD_LTHS_LSB		0x33
> +#define FXLS8962AF_SDCD_UTHS_LSB		0x35
> +
> +#define FXLS8962AF_SELF_TEST_CONFIG1		0x37
> +#define FXLS8962AF_SELF_TEST_CONFIG2		0x38
> +
> +#define FXLS8962AF_MAX_REG			0x38
> +
> +#define FXLS8962AF_DEVICE_ID			0x62
> +#define FXLS8964AF_DEVICE_ID			0x84
> +
> +#define FXLS8962AF_TEMP_CENTER_VAL		25
> +
> +#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS	2000
> +
> +#define FXLS8962AF_SCALE_TABLE_LEN		4
> +
> +static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
> +	{0, IIO_G_TO_M_S_2(980000)}, {0, IIO_G_TO_M_S_2(1950000)},
> +	{0, IIO_G_TO_M_S_2(3910000)}, {0, IIO_G_TO_M_S_2(7810000)},

perhaps more readable as one block per line?

> +};
> +
> +struct fxls8962af_chip_info {
> +	u8 chip_id;
> +	const char *name;
> +	const struct iio_chan_spec *channels;
> +	int num_channels;
> +};
> +
> +struct fxls8962af_data {
> +	struct regmap *regmap;
> +	struct mutex lock;
> +	const struct fxls8962af_chip_info *chip_info;
> +	struct regulator *vdd_reg;
> +	struct iio_mount_matrix orientation;
> +};
> +
> +const struct regmap_config fxls8962af_regmap_conf = {
> +	.reg_bits = 8,
> +	.val_bits = 8,
> +	.max_register = FXLS8962AF_MAX_REG,
> +};
> +EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
> +
> +enum {
> +	fxls8962af_idx_x,
> +	fxls8962af_idx_y,
> +	fxls8962af_idx_z,
> +	fxls8962af_idx_ts,
> +};
> +
> +static int fxls8962af_drdy(struct fxls8962af_data *data)
> +{
> +	int tries = 150, ret;
> +	unsigned int reg;
> +	struct device *dev = regmap_get_device(data->regmap);
> +
> +	while (tries-- > 0) {
> +		ret = regmap_read(data->regmap, FXLS8962AF_INT_STATUS, &reg);
> +		if (ret < 0)
> +			return ret;
> +
> +		if ((reg & FXLS8962AF_INT_STATUS_SRC_DRDY) ==
> +		    FXLS8962AF_INT_STATUS_SRC_DRDY)
> +			return 0;
> +
> +		msleep(20);
> +	}
> +
> +	dev_err(dev, "data not ready\n");
> +
> +	return -EIO;
> +}
> +
> +static int fxls8962af_set_power_state(struct fxls8962af_data *data, bool on)
> +{
> +#ifdef CONFIG_PM

I think the functions in here should all be stubbed if CONFIG_PM is not
set so much nicer to just let the compiler deal with making this do nothing.

If there is something in here that isn't safely stubbed, add a comment so
we don't 'tidy' up this in future.

> +	struct device *dev = regmap_get_device(data->regmap);
> +	int ret;
> +
> +	if (on) {
> +		ret = pm_runtime_get_sync(dev);
> +	} else {
> +		pm_runtime_mark_last_busy(dev);
> +		ret = pm_runtime_put_autosuspend(dev);
> +	}
> +
> +	if (ret < 0) {
> +		dev_err(dev, "failed to change power state to %d\n", on);
> +		if (on)
> +			pm_runtime_put_noidle(dev);
> +
> +		return ret;
> +	}
> +#endif
> +
> +	return 0;
> +}
> +
> +static int fxls8962af_get_temp(struct fxls8962af_data *data, int *val)
> +{
> +	struct device *dev = regmap_get_device(data->regmap);
> +	int ret;
> +	unsigned int value;
> +
> +	mutex_lock(&data->lock);
> +
> +	ret = fxls8962af_drdy(data);
> +	if (ret < 0) {
> +		mutex_unlock(&data->lock);

As below, use a goto and error handling block.

> +		return ret;
> +	}
> +
> +	ret = fxls8962af_set_power_state(data, true);
> +	if (ret) {
> +		mutex_unlock(&data->lock);
> +		return ret;
> +	}
> +
> +	ret = regmap_read(data->regmap, FXLS8962AF_TEMP_OUT, &value);
> +	if (ret < 0) {
> +		dev_err(dev, "Error reading reg_temp\n");
> +		fxls8962af_set_power_state(data, false);
> +		mutex_unlock(&data->lock);
> +		return ret;
> +	}
> +
> +	ret = fxls8962af_set_power_state(data, false);
> +
> +	mutex_unlock(&data->lock);
> +
> +	*val = sign_extend32(value, 7);
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	return IIO_VAL_INT;
> +}
> +
> +static int fxls8962af_get_axis(struct fxls8962af_data *data,
> +			       struct iio_chan_spec const *chan, int *val)
> +{
> +	struct device *dev = regmap_get_device(data->regmap);
> +	int ret;
> +	__le16 raw_val;
> +
> +	mutex_lock(&data->lock);
> +
> +	ret = fxls8962af_drdy(data);
> +	if (ret < 0) {
> +		mutex_unlock(&data->lock);
> +		return ret;
> +	}
> +
> +	ret = fxls8962af_set_power_state(data, true);
> +	if (ret) {
> +		mutex_unlock(&data->lock);
> +		return ret;
> +	}
> +
> +	ret = regmap_bulk_read(data->regmap, chan->address,
> +			       &raw_val, sizeof(raw_val));
> +	if (ret < 0) {
> +		dev_err(dev, "failed to read axes\n");
> +		fxls8962af_set_power_state(data, false);
> +		mutex_unlock(&data->lock);
> +		return ret;
> +	}
> +
> +	ret = fxls8962af_set_power_state(data, false);
> +
> +	mutex_unlock(&data->lock);
> +	*val = sign_extend32(le16_to_cpu(raw_val),
> +			     chan->scan_type.realbits - 1);
> +	
> +	if (ret < 0)
> +		return ret;

Hmm. This final power down error case doesn't actually affect
whether the reading is good, so I wonder if you could just report
it failing via a dev_err() message. Having done that you can then
reorganise this to push the sign_extend32... under the lock
(doesn't matter much) and that will let you combine the good and
error paths down here to share the power state change and unlock.

Alternatively you could just add an error handling block after
the return below to pull that shared handling to one place.

The same applies in some other functions
 
> +
> +	return IIO_VAL_INT;
> +}
> +
> +static int fxls8962af_read_avail(struct iio_dev *indio_dev,
> +				 struct iio_chan_spec const *chan,
> +				 const int **vals, int *type, int *length,
> +				 long mask)
> +{
> +	switch (mask) {
> +	case IIO_CHAN_INFO_SCALE:
> +		*type = IIO_VAL_INT_PLUS_NANO;
> +		*vals = (int *)fxls8962af_scale_table;
> +		*length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
> +		return IIO_AVAIL_LIST;
> +	default:
> +		return -EINVAL;
> +	}
> +}
> +
> +static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
> +					struct iio_chan_spec const *chan,
> +					long mask)
> +{
> +	return IIO_VAL_INT_PLUS_NANO;
> +}
> +
> +static int fxls8962af_standby(struct fxls8962af_data *data)
> +{
> +	return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> +				  FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
> +}
> +
> +static int fxls8962af_active(struct fxls8962af_data *data)
> +{
> +	return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> +				  FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
> +}
> +
> +static int fxls8962af_is_active(struct fxls8962af_data *data)
> +{
> +	unsigned int reg;
> +	int ret;
> +
> +	ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
> +	if (ret < 0)
> +		return ret;
> +
> +	return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
> +}
> +
> +static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
> +				    u8 mask, u8 val)
> +{
> +	int ret;
> +	int is_active;
> +
> +	mutex_lock(&data->lock);
> +
> +	is_active = fxls8962af_is_active(data);
> +	if (is_active < 0) {
> +		ret = is_active;
> +		goto fail;
> +	}
> +
> +	/* config can only be changed when in standby */
> +	if (is_active > 0) {
> +		ret = fxls8962af_standby(data);
> +		if (ret < 0)
> +			goto fail;
> +	}
> +
> +	ret = regmap_update_bits(data->regmap, reg, mask, val);
> +	if (ret < 0)
> +		goto fail;
> +
> +	if (is_active > 0) {
> +		ret = fxls8962af_active(data);
> +		if (ret < 0)
> +			goto fail;
> +	}
> +
> +	ret = 0;

How do you get here without it being 0?
Note regmap_update_bits returns <= 0 only so if (ret) above will make
the flow more obvious and avoid compilers moaning.


> + fail:
> +	mutex_unlock(&data->lock);
> +
> +	return ret;
> +}
> +
> +static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
> +{
> +	int i;
> +
> +	for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
> +		if (scale == fxls8962af_scale_table[i][1])
> +			break;
> +
> +	if (i == ARRAY_SIZE(fxls8962af_scale_table))
> +		return -EINVAL;
> +
> +	return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
> +					FXLS8962AF_FSR_MASK,
> +					i << FXLS8962AF_FSR_SHIFT);
> +}
> +
> +static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
> +					       int *val)
> +{
> +	int ret;
> +	unsigned int reg;
> +	u8 range_idx;
> +
> +	ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
> +	if (ret < 0)
> +		return ret;
> +
> +	range_idx = (reg & FXLS8962AF_FSR_MASK) >> FXLS8962AF_FSR_SHIFT;
> +
> +	*val = fxls8962af_scale_table[range_idx][1];
> +
> +	return IIO_VAL_INT_PLUS_NANO;
> +}
> +
> +static int fxls8962af_read_raw(struct iio_dev *indio_dev,
> +			       struct iio_chan_spec const *chan,
> +			       int *val, int *val2, long mask)
> +{
> +	struct fxls8962af_data *data = iio_priv(indio_dev);
> +	int ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		ret = iio_device_claim_direct_mode(indio_dev);
> +		if (ret)
> +			return ret;
> +
> +		switch (chan->type) {
> +		case IIO_TEMP:
> +			ret = fxls8962af_get_temp(data, val);
> +			break;
> +		case IIO_ACCEL:
> +			ret = fxls8962af_get_axis(data, chan, val);
> +			break;
> +		default:
> +			ret = -EINVAL;
> +		}
> +
> +		iio_device_release_direct_mode(indio_dev);
> +		return ret;
> +	case IIO_CHAN_INFO_OFFSET:
> +		if (chan->type == IIO_TEMP) {
> +			*val = FXLS8962AF_TEMP_CENTER_VAL;
> +			return IIO_VAL_INT;
> +		} else {
> +			return -EINVAL;
> +		}
> +	case IIO_CHAN_INFO_SCALE:
> +		*val = 0;
> +		ret = fxls8962af_read_full_scale(data, val2);
> +		return ret;
> +	default:
> +		ret = -EINVAL;
> +		break;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int fxls8962af_write_raw(struct iio_dev *indio_dev,
> +				struct iio_chan_spec const *chan,
> +				int val, int val2, long mask)
> +{
> +	struct fxls8962af_data *data = iio_priv(indio_dev);
> +	int ret;
> +
> +	ret = iio_device_claim_direct_mode(indio_dev);
> +	if (ret)
I would move this to where we need it around the set_full_scale
call alone.  Lets us do direct returns in other paths...
> +		return ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_SCALE:
> +		if(val != 0)

for example here.  Right now this just exited with direct mode
still claimed and hence broke any future access to the device.
(it's effectively a lock, be it a somewhat odd one)

> +			return -EINVAL;
> +
> +		ret = fxls8962af_set_full_scale(data, val2);
> +		break;
> +	default:
> +		ret = -EINVAL;
> +		break;
> +	}
> +
> +	iio_device_release_direct_mode(indio_dev);
> +	return ret;
> +}
> +
> +#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
> +	.type = IIO_ACCEL, \
> +	.address = reg, \
> +	.modified = 1, \
> +	.channel2 = IIO_MOD_##axis, \
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> +	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> +	.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
> +	.scan_index = idx, \
> +	.scan_type = { \
> +		.sign = 's', \
> +		.realbits = 12, \
> +		.storagebits = 16, \
> +		.shift = 4, \
> +		.endianness = IIO_BE, \
> +	}, \
> +}
> +
> +#define FXLS8962AF_TEMP_CHANNEL { \
> +	.type = IIO_TEMP, \
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
> +			      BIT(IIO_CHAN_INFO_OFFSET),\
> +	.scan_index = -1, \
> +	.scan_type = { \
> +		.sign = 's', \
> +		.realbits = 8, \
> +		.storagebits = 16, \
Scan type doesn't mean anything for channels that aren't in the scan
(scan_index == -1) I see you do use realbits to do the sign extension
which is fine, but I wouldn't add any elements that aren't used such
as storagebits which is missleading I think

> +	}, \
> +}
> +
> +static const struct iio_chan_spec fxls8962af_channels[] = {
> +	FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
> +	FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
> +	FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
> +	IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
> +	FXLS8962AF_TEMP_CHANNEL,
> +};
> +
> +static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
> +	[fxls8962af] = {
> +		.chip_id = FXLS8962AF_DEVICE_ID,
> +		.name = "fxls8962af",
> +		.channels = fxls8962af_channels,
> +		.num_channels = ARRAY_SIZE(fxls8962af_channels),
> +	},
> +	[fxls8964af] = {
> +		.chip_id = FXLS8964AF_DEVICE_ID,
> +		.name = "fxls8964af",
> +		.channels = fxls8962af_channels,
> +		.num_channels = ARRAY_SIZE(fxls8962af_channels),
> +	}
> +};
> +
> +static const struct iio_info fxls8962af_info = {
> +	.read_raw = &fxls8962af_read_raw,
> +	.write_raw = &fxls8962af_write_raw,
> +	.write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
> +	.read_avail = fxls8962af_read_avail,
> +};
> +
> +static int fxls8962af_reset(struct fxls8962af_data *data)
> +{
> +	int i, ret;
> +	unsigned int reg;
> +
> +	ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> +				 FXLS8962AF_SENS_CONFIG1_RST,
> +				 FXLS8962AF_SENS_CONFIG1_RST);
> +	if (ret < 0)
> +		return ret;
> +
> +	for (i = 0; i < 10; i++) {
> +		usleep_range(100, 200);

Do we have a better idea from the datasheet for how long this should take?
It is not a hot path so maybe just wait until after that and check once
that it succeeded?

> +		ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
> +		if (ret == -EIO)
> +			continue;	/* I2C comm reset */
> +		if (ret < 0)
> +			return ret;
> +		if (!(reg & FXLS8962AF_SENS_CONFIG1_RST))
> +			return 0;
> +	}
> +
> +	return -ETIMEDOUT;
> +}
> +
> +static void fxls8962af_regulator_disable(void *data_ptr)
> +{
> +	struct fxls8962af_data *data = data_ptr;
> +
> +	regulator_disable(data->vdd_reg);
> +}
> +
> +static void fxls8962af_pm_disable(void *dev_ptr)
> +{
> +	struct device *dev = dev_ptr;
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +
> +	pm_runtime_disable(dev);
> +	pm_runtime_set_suspended(dev);
> +	pm_runtime_put_noidle(dev);
> +
> +	fxls8962af_standby(iio_priv(indio_dev));
> +}
> +
> +int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
> +{
> +	struct fxls8962af_data *data;
> +	struct iio_dev *indio_dev;
> +	unsigned int reg;
> +	int ret, i;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	data = iio_priv(indio_dev);
> +	dev_set_drvdata(dev, indio_dev);
> +	mutex_init(&data->lock);
> +	data->regmap = regmap;
> +
> +	ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation);
> +	if (ret)
> +		return ret;
> +
> +	data->vdd_reg = devm_regulator_get(dev, "vdd");
> +	if (IS_ERR(data->vdd_reg))
> +		return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
> +				     "Failed to get vdd regulator\n");
> +
> +	ret = regulator_enable(data->vdd_reg);
> +	if (ret) {
> +		dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, &reg);
> +	if (ret < 0)
> +		return ret;
> +
> +	for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
> +		if (fxls_chip_info_table[i].chip_id == reg) {
> +			data->chip_info = &fxls_chip_info_table[i];
> +			break;

Check we matched one of them?

> +		}
> +	}
> +
> +	indio_dev->channels = data->chip_info->channels;
> +	indio_dev->num_channels = data->chip_info->num_channels;
> +	indio_dev->name = data->chip_info->name;
> +	indio_dev->info = &fxls8962af_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +
> +	ret = fxls8962af_reset(data);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = pm_runtime_set_active(dev);
> +	if (ret < 0)
> +		return ret;
> +
> +	pm_runtime_enable(dev);
> +	pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
> +	pm_runtime_use_autosuspend(dev);
> +
> +	ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
> +	if (ret)
> +		return ret;
> +
> +
> +	return devm_iio_device_register(dev, indio_dev);
> +
> +}
> +EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
> +
> +#ifdef CONFIG_PM

Drop the ifdef as it goes wrong far too often (there are odd corners
of what can be enabled wrt to power management) and mark these
__maybe_unused instead.   They'll get dropped anyway by the linker
if not used.

> +static int fxls8962af_runtime_suspend(struct device *dev)
> +{
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct fxls8962af_data *data = iio_priv(indio_dev);

If you don't need indio_dev locally, then
	struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
doesn't use any meaning and is a tiny bit more compact.

> +	int ret;
> +
> +	mutex_lock(&data->lock);
> +	ret = fxls8962af_standby(data);
> +	mutex_unlock(&data->lock);

Why do we need locks in this direction but not in resume?
Perhaps a comment here would clarify that.

> +	if (ret < 0) {
> +		dev_err(dev, "powering off device failed\n");
> +		return -EAGAIN;

Don't eat what might be a more specific error value.

> +	}
> +
> +	return 0;
> +}
> +
> +static int fxls8962af_runtime_resume(struct device *dev)
> +{
> +	struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +	struct fxls8962af_data *data = iio_priv(indio_dev);
> +	int ret;
> +
> +	ret = fxls8962af_active(data);

return fxls8962af_active(data);

> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +#endif
> +
> +const struct dev_pm_ops fxls8962af_pm_ops = {
> +	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> +				pm_runtime_force_resume)
> +	SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
> +			   fxls8962af_runtime_resume, NULL)
> +};
> +EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
> +
> +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
> +MODULE_LICENSE("GPL v2");