* [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files
@ 2021-04-01 20:08 Peter Robinson
2021-04-01 20:08 ` [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control Peter Robinson
` (5 more replies)
0 siblings, 6 replies; 10+ messages in thread
From: Peter Robinson @ 2021-04-01 20:08 UTC (permalink / raw)
To: u-boot
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
arch/arm/dts/Makefile | 5 +-
arch/arm/dts/imx6sx-pinfunc.h | 286 ++++++++++-----
arch/arm/dts/imx6sx-udoo-neo-basic.dts | 33 ++
arch/arm/dts/imx6sx-udoo-neo-extended.dts | 26 ++
arch/arm/dts/imx6sx-udoo-neo-full.dts | 41 +++
arch/arm/dts/imx6sx-udoo-neo.dtsi | 410 ++++++++++++++++++++++
6 files changed, 714 insertions(+), 87 deletions(-)
create mode 100644 arch/arm/dts/imx6sx-udoo-neo-basic.dts
create mode 100644 arch/arm/dts/imx6sx-udoo-neo-extended.dts
create mode 100644 arch/arm/dts/imx6sx-udoo-neo-full.dts
create mode 100644 arch/arm/dts/imx6sx-udoo-neo.dtsi
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index c6710826a0..793cba3956 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -736,7 +736,10 @@ dtb-$(CONFIG_MX6SLL) += imx6sll-evk.dtb
dtb-$(CONFIG_MX6SX) += \
imx6sx-sabreauto.dtb \
imx6sx-sdb.dtb \
- imx6sx-softing-vining-2000.dtb
+ imx6sx-softing-vining-2000.dtb \
+ imx6sx-udoo-neo-basic.dtb \
+ imx6sx-udoo-neo-extended.dtb \
+ imx6sx-udoo-neo-full.dtb
dtb-$(CONFIG_MX6UL) += \
imx6ul-geam.dtb \
diff --git a/arch/arm/dts/imx6sx-pinfunc.h b/arch/arm/dts/imx6sx-pinfunc.h
index aa194a2fdd..f4dc462079 100644
--- a/arch/arm/dts/imx6sx-pinfunc.h
+++ b/arch/arm/dts/imx6sx-pinfunc.h
@@ -42,8 +42,8 @@
#define MX6SX_PAD_GPIO1_IO03__GPIO1_IO_3 0x0020 0x0368 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO03__CCM_PLL3_BYP 0x0020 0x0368 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO03__PHY_TCK 0x0020 0x0368 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO04__UART1_RX 0x0024 0x036C 0x0830 0x0 0x0
-#define MX6SX_PAD_GPIO1_IO04__UART1_TX 0x0024 0x036C 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX 0x0024 0x036C 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO04__UART1_DTE_RX 0x0024 0x036C 0x0830 0x0 0x0
#define MX6SX_PAD_GPIO1_IO04__USDHC2_RESET_B 0x0024 0x036C 0x0000 0x1 0x0
#define MX6SX_PAD_GPIO1_IO04__ENET1_MDC 0x0024 0x036C 0x0000 0x2 0x0
#define MX6SX_PAD_GPIO1_IO04__OSC32K_32K_OUT 0x0024 0x036C 0x0000 0x3 0x0
@@ -51,8 +51,8 @@
#define MX6SX_PAD_GPIO1_IO04__GPIO1_IO_4 0x0024 0x036C 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO04__CCM_PLL2_BYP 0x0024 0x036C 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO04__PHY_TMS 0x0024 0x036C 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO05__UART1_RX 0x0028 0x0370 0x0830 0x0 0x1
-#define MX6SX_PAD_GPIO1_IO05__UART1_TX 0x0028 0x0370 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX 0x0028 0x0370 0x0830 0x0 0x1
+#define MX6SX_PAD_GPIO1_IO05__UART1_DTE_TX 0x0028 0x0370 0x0000 0x0 0x0
#define MX6SX_PAD_GPIO1_IO05__USDHC2_VSELECT 0x0028 0x0370 0x0000 0x1 0x0
#define MX6SX_PAD_GPIO1_IO05__ENET1_MDIO 0x0028 0x0370 0x0764 0x2 0x0
#define MX6SX_PAD_GPIO1_IO05__ASRC_ASRC_EXT_CLK 0x0028 0x0370 0x0000 0x3 0x0
@@ -60,21 +60,23 @@
#define MX6SX_PAD_GPIO1_IO05__GPIO1_IO_5 0x0028 0x0370 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO05__SRC_TESTER_ACK 0x0028 0x0370 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO05__PHY_TDO 0x0028 0x0370 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART2_RX 0x002C 0x0374 0x0838 0x0 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART2_TX 0x002C 0x0374 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX 0x002C 0x0374 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART2_DTE_RX 0x002C 0x0374 0x0838 0x0 0x0
#define MX6SX_PAD_GPIO1_IO06__USDHC2_CD_B 0x002C 0x0374 0x086C 0x1 0x1
#define MX6SX_PAD_GPIO1_IO06__ENET2_MDC 0x002C 0x0374 0x0000 0x2 0x0
#define MX6SX_PAD_GPIO1_IO06__CSI1_MCLK 0x002C 0x0374 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART1_RTS_B 0x002C 0x0374 0x082C 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART1_DCE_RTS 0x002C 0x0374 0x082C 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART1_DTE_CTS 0x002C 0x0374 0x0000 0x4 0x0
#define MX6SX_PAD_GPIO1_IO06__GPIO1_IO_6 0x002C 0x0374 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO06__SRC_ANY_PU_RESET 0x002C 0x0374 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO06__OCOTP_CTRL_WRAPPER_FUSE_LATCHED 0x002C 0x0374 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO07__UART2_RX 0x0030 0x0378 0x0838 0x0 0x1
-#define MX6SX_PAD_GPIO1_IO07__UART2_TX 0x0030 0x0378 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX 0x0030 0x0378 0x0838 0x0 0x1
+#define MX6SX_PAD_GPIO1_IO07__UART2_DTE_TX 0x0030 0x0378 0x0000 0x0 0x0
#define MX6SX_PAD_GPIO1_IO07__USDHC2_WP 0x0030 0x0378 0x0870 0x1 0x1
#define MX6SX_PAD_GPIO1_IO07__ENET2_MDIO 0x0030 0x0378 0x0770 0x2 0x0
#define MX6SX_PAD_GPIO1_IO07__AUDMUX_MCLK 0x0030 0x0378 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO07__UART1_CTS_B 0x0030 0x0378 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART1_DCE_CTS 0x0030 0x0378 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART1_DTE_RTS 0x0030 0x0378 0x082C 0x4 0x1
#define MX6SX_PAD_GPIO1_IO07__GPIO1_IO_7 0x0030 0x0378 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO07__SRC_EARLY_RESET 0x0030 0x0378 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO07__DCIC2_OUT 0x0030 0x0378 0x0000 0x7 0x0
@@ -83,7 +85,8 @@
#define MX6SX_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0034 0x037C 0x0000 0x1 0x0
#define MX6SX_PAD_GPIO1_IO08__SDMA_EXT_EVENT_0 0x0034 0x037C 0x081C 0x2 0x0
#define MX6SX_PAD_GPIO1_IO08__CCM_PMIC_RDY 0x0034 0x037C 0x069C 0x3 0x1
-#define MX6SX_PAD_GPIO1_IO08__UART2_RTS_B 0x0034 0x037C 0x0834 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO08__UART2_DCE_RTS 0x0034 0x037C 0x0834 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO08__UART2_DTE_CTS 0x0034 0x037C 0x0000 0x4 0x0
#define MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x0034 0x037C 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO08__SRC_SYSTEM_RESET 0x0034 0x037C 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO08__DCIC1_OUT 0x0034 0x037C 0x0000 0x7 0x0
@@ -92,7 +95,8 @@
#define MX6SX_PAD_GPIO1_IO09__WDOG2_WDOG_B 0x0038 0x0380 0x0000 0x1 0x0
#define MX6SX_PAD_GPIO1_IO09__SDMA_EXT_EVENT_1 0x0038 0x0380 0x0820 0x2 0x0
#define MX6SX_PAD_GPIO1_IO09__CCM_OUT0 0x0038 0x0380 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO09__UART2_CTS_B 0x0038 0x0380 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO09__UART2_DCE_CTS 0x0038 0x0380 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO09__UART2_DTE_RTS 0x0038 0x0380 0x0834 0x4 0x1
#define MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x0038 0x0380 0x0000 0x5 0x0
#define MX6SX_PAD_GPIO1_IO09__SRC_INT_BOOT 0x0038 0x0380 0x0000 0x6 0x0
#define MX6SX_PAD_GPIO1_IO09__OBSERVE_MUX_OUT_4 0x0038 0x0380 0x0000 0x7 0x0
@@ -177,8 +181,8 @@
#define MX6SX_PAD_CSI_DATA04__ESAI_TX1 0x005C 0x03A4 0x0794 0x1 0x1
#define MX6SX_PAD_CSI_DATA04__SPDIF_OUT 0x005C 0x03A4 0x0000 0x2 0x0
#define MX6SX_PAD_CSI_DATA04__KPP_COL_6 0x005C 0x03A4 0x07CC 0x3 0x0
-#define MX6SX_PAD_CSI_DATA04__UART6_RX 0x005C 0x03A4 0x0858 0x4 0x0
-#define MX6SX_PAD_CSI_DATA04__UART6_TX 0x005C 0x03A4 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA04__UART6_DCE_RX 0x005C 0x03A4 0x0858 0x4 0x0
+#define MX6SX_PAD_CSI_DATA04__UART6_DTE_TX 0x005C 0x03A4 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x005C 0x03A4 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_DATA04__WEIM_DATA_19 0x005C 0x03A4 0x0000 0x6 0x0
#define MX6SX_PAD_CSI_DATA04__PWM5_OUT 0x005C 0x03A4 0x0000 0x7 0x0
@@ -188,8 +192,8 @@
#define MX6SX_PAD_CSI_DATA05__ESAI_TX4_RX1 0x0060 0x03A8 0x07A0 0x1 0x1
#define MX6SX_PAD_CSI_DATA05__SPDIF_IN 0x0060 0x03A8 0x0824 0x2 0x1
#define MX6SX_PAD_CSI_DATA05__KPP_ROW_6 0x0060 0x03A8 0x07D8 0x3 0x0
-#define MX6SX_PAD_CSI_DATA05__UART6_RX 0x0060 0x03A8 0x0858 0x4 0x1
-#define MX6SX_PAD_CSI_DATA05__UART6_TX 0x0060 0x03A8 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA05__UART6_DCE_TX 0x0060 0x03A8 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA05__UART6_DTE_RX 0x0060 0x03A8 0x0858 0x4 0x1
#define MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x0060 0x03A8 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_DATA05__WEIM_DATA_18 0x0060 0x03A8 0x0000 0x6 0x0
#define MX6SX_PAD_CSI_DATA05__PWM6_OUT 0x0060 0x03A8 0x0000 0x7 0x0
@@ -199,7 +203,8 @@
#define MX6SX_PAD_CSI_DATA06__ESAI_TX2_RX3 0x0064 0x03AC 0x0798 0x1 0x1
#define MX6SX_PAD_CSI_DATA06__I2C4_SCL 0x0064 0x03AC 0x07C0 0x2 0x2
#define MX6SX_PAD_CSI_DATA06__KPP_COL_7 0x0064 0x03AC 0x07D0 0x3 0x0
-#define MX6SX_PAD_CSI_DATA06__UART6_RTS_B 0x0064 0x03AC 0x0854 0x4 0x0
+#define MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS 0x0064 0x03AC 0x0854 0x4 0x0
+#define MX6SX_PAD_CSI_DATA06__UART6_DTE_CTS 0x0064 0x03AC 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_DATA06__GPIO1_IO_20 0x0064 0x03AC 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_DATA06__WEIM_DATA_17 0x0064 0x03AC 0x0000 0x6 0x0
#define MX6SX_PAD_CSI_DATA06__DCIC2_OUT 0x0064 0x03AC 0x0000 0x7 0x0
@@ -209,7 +214,8 @@
#define MX6SX_PAD_CSI_DATA07__ESAI_TX3_RX2 0x0068 0x03B0 0x079C 0x1 0x1
#define MX6SX_PAD_CSI_DATA07__I2C4_SDA 0x0068 0x03B0 0x07C4 0x2 0x2
#define MX6SX_PAD_CSI_DATA07__KPP_ROW_7 0x0068 0x03B0 0x07DC 0x3 0x0
-#define MX6SX_PAD_CSI_DATA07__UART6_CTS_B 0x0068 0x03B0 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS 0x0068 0x03B0 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA07__UART6_DTE_RTS 0x0068 0x03B0 0x0854 0x4 0x1
#define MX6SX_PAD_CSI_DATA07__GPIO1_IO_21 0x0068 0x03B0 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_DATA07__WEIM_DATA_16 0x0068 0x03B0 0x0000 0x6 0x0
#define MX6SX_PAD_CSI_DATA07__DCIC1_OUT 0x0068 0x03B0 0x0000 0x7 0x0
@@ -218,7 +224,8 @@
#define MX6SX_PAD_CSI_HSYNC__CSI1_HSYNC 0x006C 0x03B4 0x0700 0x0 0x0
#define MX6SX_PAD_CSI_HSYNC__ESAI_TX0 0x006C 0x03B4 0x0790 0x1 0x1
#define MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD 0x006C 0x03B4 0x0678 0x2 0x1
-#define MX6SX_PAD_CSI_HSYNC__UART4_RTS_B 0x006C 0x03B4 0x0844 0x3 0x2
+#define MX6SX_PAD_CSI_HSYNC__UART4_DCE_RTS 0x006C 0x03B4 0x0844 0x3 0x2
+#define MX6SX_PAD_CSI_HSYNC__UART4_DTE_CTS 0x006C 0x03B4 0x0000 0x3 0x0
#define MX6SX_PAD_CSI_HSYNC__MQS_LEFT 0x006C 0x03B4 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_HSYNC__GPIO1_IO_22 0x006C 0x03B4 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_HSYNC__WEIM_DATA_25 0x006C 0x03B4 0x0000 0x6 0x0
@@ -228,8 +235,8 @@
#define MX6SX_PAD_CSI_MCLK__CSI1_MCLK 0x0070 0x03B8 0x0000 0x0 0x0
#define MX6SX_PAD_CSI_MCLK__ESAI_TX_HF_CLK 0x0070 0x03B8 0x0784 0x1 0x1
#define MX6SX_PAD_CSI_MCLK__OSC32K_32K_OUT 0x0070 0x03B8 0x0000 0x2 0x0
-#define MX6SX_PAD_CSI_MCLK__UART4_RX 0x0070 0x03B8 0x0848 0x3 0x2
-#define MX6SX_PAD_CSI_MCLK__UART4_TX 0x0070 0x03B8 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_MCLK__UART4_DCE_RX 0x0070 0x03B8 0x0848 0x3 0x2
+#define MX6SX_PAD_CSI_MCLK__UART4_DTE_TX 0x0070 0x03B8 0x0000 0x3 0x0
#define MX6SX_PAD_CSI_MCLK__ANATOP_32K_OUT 0x0070 0x03B8 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_MCLK__GPIO1_IO_23 0x0070 0x03B8 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_MCLK__WEIM_DATA_26 0x0070 0x03B8 0x0000 0x6 0x0
@@ -239,8 +246,8 @@
#define MX6SX_PAD_CSI_PIXCLK__CSI1_PIXCLK 0x0074 0x03BC 0x0704 0x0 0x0
#define MX6SX_PAD_CSI_PIXCLK__ESAI_RX_HF_CLK 0x0074 0x03BC 0x0780 0x1 0x1
#define MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK 0x0074 0x03BC 0x0000 0x2 0x0
-#define MX6SX_PAD_CSI_PIXCLK__UART4_RX 0x0074 0x03BC 0x0848 0x3 0x3
-#define MX6SX_PAD_CSI_PIXCLK__UART4_TX 0x0074 0x03BC 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_PIXCLK__UART4_DCE_TX 0x0074 0x03BC 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_PIXCLK__UART4_DTE_RX 0x0074 0x03BC 0x0848 0x3 0x3
#define MX6SX_PAD_CSI_PIXCLK__ANATOP_24M_OUT 0x0074 0x03BC 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_PIXCLK__GPIO1_IO_24 0x0074 0x03BC 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_PIXCLK__WEIM_DATA_27 0x0074 0x03BC 0x0000 0x6 0x0
@@ -250,7 +257,8 @@
#define MX6SX_PAD_CSI_VSYNC__CSI1_VSYNC 0x0078 0x03C0 0x0708 0x0 0x0
#define MX6SX_PAD_CSI_VSYNC__ESAI_TX5_RX0 0x0078 0x03C0 0x07A4 0x1 0x1
#define MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD 0x0078 0x03C0 0x0674 0x2 0x1
-#define MX6SX_PAD_CSI_VSYNC__UART4_CTS_B 0x0078 0x03C0 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_VSYNC__UART4_DCE_CTS 0x0078 0x03C0 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_VSYNC__UART4_DTE_RTS 0x0078 0x03C0 0x0844 0x3 0x3
#define MX6SX_PAD_CSI_VSYNC__MQS_RIGHT 0x0078 0x03C0 0x0000 0x4 0x0
#define MX6SX_PAD_CSI_VSYNC__GPIO1_IO_25 0x0078 0x03C0 0x0000 0x5 0x0
#define MX6SX_PAD_CSI_VSYNC__WEIM_DATA_24 0x0078 0x03C0 0x0000 0x6 0x0
@@ -330,8 +338,8 @@
#define MX6SX_PAD_ENET2_COL__ENET2_COL 0x0094 0x03DC 0x0000 0x0 0x0
#define MX6SX_PAD_ENET2_COL__ENET1_MDC 0x0094 0x03DC 0x0000 0x1 0x0
#define MX6SX_PAD_ENET2_COL__AUDMUX_AUD4_RXC 0x0094 0x03DC 0x064C 0x2 0x1
-#define MX6SX_PAD_ENET2_COL__UART1_RX 0x0094 0x03DC 0x0830 0x3 0x2
-#define MX6SX_PAD_ENET2_COL__UART1_TX 0x0094 0x03DC 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_COL__UART1_DCE_RX 0x0094 0x03DC 0x0830 0x3 0x2
+#define MX6SX_PAD_ENET2_COL__UART1_DTE_TX 0x0094 0x03DC 0x0000 0x3 0x0
#define MX6SX_PAD_ENET2_COL__SPDIF_IN 0x0094 0x03DC 0x0824 0x4 0x3
#define MX6SX_PAD_ENET2_COL__GPIO2_IO_6 0x0094 0x03DC 0x0000 0x5 0x0
#define MX6SX_PAD_ENET2_COL__ANATOP_OTG1_ID 0x0094 0x03DC 0x0624 0x6 0x1
@@ -341,8 +349,8 @@
#define MX6SX_PAD_ENET2_CRS__ENET2_CRS 0x0098 0x03E0 0x0000 0x0 0x0
#define MX6SX_PAD_ENET2_CRS__ENET1_MDIO 0x0098 0x03E0 0x0764 0x1 0x2
#define MX6SX_PAD_ENET2_CRS__AUDMUX_AUD4_RXFS 0x0098 0x03E0 0x0650 0x2 0x1
-#define MX6SX_PAD_ENET2_CRS__UART1_RX 0x0098 0x03E0 0x0830 0x3 0x3
-#define MX6SX_PAD_ENET2_CRS__UART1_TX 0x0098 0x03E0 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_CRS__UART1_DCE_TX 0x0098 0x03E0 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_CRS__UART1_DTE_RX 0x0098 0x03E0 0x0830 0x3 0x3
#define MX6SX_PAD_ENET2_CRS__MLB_SIG 0x0098 0x03E0 0x07F0 0x4 0x1
#define MX6SX_PAD_ENET2_CRS__GPIO2_IO_7 0x0098 0x03E0 0x0000 0x5 0x0
#define MX6SX_PAD_ENET2_CRS__ANATOP_OTG2_ID 0x0098 0x03E0 0x0628 0x6 0x1
@@ -352,7 +360,8 @@
#define MX6SX_PAD_ENET2_RX_CLK__ENET2_RX_CLK 0x009C 0x03E4 0x0774 0x0 0x0
#define MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x009C 0x03E4 0x0000 0x1 0x0
#define MX6SX_PAD_ENET2_RX_CLK__I2C3_SCL 0x009C 0x03E4 0x07B8 0x2 0x1
-#define MX6SX_PAD_ENET2_RX_CLK__UART1_RTS_B 0x009C 0x03E4 0x082C 0x3 0x2
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_DCE_RTS 0x009C 0x03E4 0x082C 0x3 0x2
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_DTE_CTS 0x009C 0x03E4 0x0000 0x3 0x0
#define MX6SX_PAD_ENET2_RX_CLK__MLB_DATA 0x009C 0x03E4 0x07EC 0x4 0x1
#define MX6SX_PAD_ENET2_RX_CLK__GPIO2_IO_8 0x009C 0x03E4 0x0000 0x5 0x0
#define MX6SX_PAD_ENET2_RX_CLK__USB_OTG2_OC 0x009C 0x03E4 0x085C 0x6 0x1
@@ -362,7 +371,8 @@
#define MX6SX_PAD_ENET2_TX_CLK__ENET2_TX_CLK 0x00A0 0x03E8 0x0000 0x0 0x0
#define MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x00A0 0x03E8 0x076C 0x1 0x1
#define MX6SX_PAD_ENET2_TX_CLK__I2C3_SDA 0x00A0 0x03E8 0x07BC 0x2 0x1
-#define MX6SX_PAD_ENET2_TX_CLK__UART1_CTS_B 0x00A0 0x03E8 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_DCE_CTS 0x00A0 0x03E8 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_DTE_RTS 0x00A0 0x03E8 0x082C 0x3 0x3
#define MX6SX_PAD_ENET2_TX_CLK__MLB_CLK 0x00A0 0x03E8 0x07E8 0x4 0x1
#define MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9 0x00A0 0x03E8 0x0000 0x5 0x0
#define MX6SX_PAD_ENET2_TX_CLK__USB_OTG2_PWR 0x00A0 0x03E8 0x0000 0x6 0x0
@@ -371,7 +381,8 @@
#define MX6SX_PAD_ENET2_TX_CLK__PCIE_CTRL_DEBUG_24 0x00A0 0x03E8 0x0000 0x9 0x0
#define MX6SX_PAD_KEY_COL0__KPP_COL_0 0x00A4 0x03EC 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_COL0__USDHC3_CD_B 0x00A4 0x03EC 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL0__UART6_RTS_B 0x00A4 0x03EC 0x0854 0x2 0x2
+#define MX6SX_PAD_KEY_COL0__UART6_DCE_RTS 0x00A4 0x03EC 0x0854 0x2 0x2
+#define MX6SX_PAD_KEY_COL0__UART6_DTE_CTS 0x00A4 0x03EC 0x0000 0x2 0x0
#define MX6SX_PAD_KEY_COL0__ECSPI1_SCLK 0x00A4 0x03EC 0x0710 0x3 0x0
#define MX6SX_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x00A4 0x03EC 0x066C 0x4 0x0
#define MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x00A4 0x03EC 0x0000 0x5 0x0
@@ -380,8 +391,8 @@
#define MX6SX_PAD_KEY_COL0__VADC_DATA_0 0x00A4 0x03EC 0x0000 0x8 0x0
#define MX6SX_PAD_KEY_COL1__KPP_COL_1 0x00A8 0x03F0 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_COL1__USDHC3_RESET_B 0x00A8 0x03F0 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL1__UART6_RX 0x00A8 0x03F0 0x0858 0x2 0x2
-#define MX6SX_PAD_KEY_COL1__UART6_TX 0x00A8 0x03F0 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL1__UART6_DCE_TX 0x00A8 0x03F0 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL1__UART6_DTE_RX 0x00A8 0x03F0 0x0858 0x2 0x2
#define MX6SX_PAD_KEY_COL1__ECSPI1_MISO 0x00A8 0x03F0 0x0714 0x3 0x0
#define MX6SX_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x00A8 0x03F0 0x0670 0x4 0x0
#define MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x00A8 0x03F0 0x0000 0x5 0x0
@@ -389,7 +400,8 @@
#define MX6SX_PAD_KEY_COL1__SAI2_TX_SYNC 0x00A8 0x03F0 0x0818 0x7 0x0
#define MX6SX_PAD_KEY_COL2__KPP_COL_2 0x00AC 0x03F4 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_COL2__USDHC4_CD_B 0x00AC 0x03F4 0x0874 0x1 0x1
-#define MX6SX_PAD_KEY_COL2__UART5_RTS_B 0x00AC 0x03F4 0x084C 0x2 0x2
+#define MX6SX_PAD_KEY_COL2__UART5_DCE_RTS 0x00AC 0x03F4 0x084C 0x2 0x2
+#define MX6SX_PAD_KEY_COL2__UART5_DTE_CTS 0x00AC 0x03F4 0x0000 0x2 0x0
#define MX6SX_PAD_KEY_COL2__CAN1_TX 0x00AC 0x03F4 0x0000 0x3 0x0
#define MX6SX_PAD_KEY_COL2__CANFD_TX1 0x00AC 0x03F4 0x0000 0x4 0x0
#define MX6SX_PAD_KEY_COL2__GPIO2_IO_12 0x00AC 0x03F4 0x0000 0x5 0x0
@@ -397,8 +409,8 @@
#define MX6SX_PAD_KEY_COL2__ECSPI1_RDY 0x00AC 0x03F4 0x0000 0x7 0x0
#define MX6SX_PAD_KEY_COL3__KPP_COL_3 0x00B0 0x03F8 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_COL3__USDHC4_LCTL 0x00B0 0x03F8 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL3__UART5_RX 0x00B0 0x03F8 0x0850 0x2 0x2
-#define MX6SX_PAD_KEY_COL3__UART5_TX 0x00B0 0x03F8 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL3__UART5_DCE_TX 0x00B0 0x03F8 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL3__UART5_DTE_RX 0x00B0 0x03F8 0x0850 0x2 0x2
#define MX6SX_PAD_KEY_COL3__CAN2_TX 0x00B0 0x03F8 0x0000 0x3 0x0
#define MX6SX_PAD_KEY_COL3__CANFD_TX2 0x00B0 0x03F8 0x0000 0x4 0x0
#define MX6SX_PAD_KEY_COL3__GPIO2_IO_13 0x00B0 0x03F8 0x0000 0x5 0x0
@@ -414,7 +426,8 @@
#define MX6SX_PAD_KEY_COL4__SAI2_RX_BCLK 0x00B4 0x03FC 0x0808 0x7 0x0
#define MX6SX_PAD_KEY_ROW0__KPP_ROW_0 0x00B8 0x0400 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_ROW0__USDHC3_WP 0x00B8 0x0400 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW0__UART6_CTS_B 0x00B8 0x0400 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW0__UART6_DCE_CTS 0x00B8 0x0400 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW0__UART6_DTE_RTS 0x00B8 0x0400 0x0854 0x2 0x3
#define MX6SX_PAD_KEY_ROW0__ECSPI1_MOSI 0x00B8 0x0400 0x0718 0x3 0x0
#define MX6SX_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x00B8 0x0400 0x0660 0x4 0x0
#define MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x00B8 0x0400 0x0000 0x5 0x0
@@ -423,8 +436,8 @@
#define MX6SX_PAD_KEY_ROW0__GPU_IDLE 0x00B8 0x0400 0x0000 0x8 0x0
#define MX6SX_PAD_KEY_ROW1__KPP_ROW_1 0x00BC 0x0404 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_ROW1__USDHC4_VSELECT 0x00BC 0x0404 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW1__UART6_RX 0x00BC 0x0404 0x0858 0x2 0x3
-#define MX6SX_PAD_KEY_ROW1__UART6_TX 0x00BC 0x0404 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW1__UART6_DCE_RX 0x00BC 0x0404 0x0858 0x2 0x3
+#define MX6SX_PAD_KEY_ROW1__UART6_DTE_TX 0x00BC 0x0404 0x0000 0x2 0x0
#define MX6SX_PAD_KEY_ROW1__ECSPI1_SS0 0x00BC 0x0404 0x071C 0x3 0x0
#define MX6SX_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x00BC 0x0404 0x065C 0x4 0x0
#define MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x00BC 0x0404 0x0000 0x5 0x0
@@ -433,7 +446,8 @@
#define MX6SX_PAD_KEY_ROW1__M4_NMI 0x00BC 0x0404 0x0000 0x8 0x0
#define MX6SX_PAD_KEY_ROW2__KPP_ROW_2 0x00C0 0x0408 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_ROW2__USDHC4_WP 0x00C0 0x0408 0x0878 0x1 0x1
-#define MX6SX_PAD_KEY_ROW2__UART5_CTS_B 0x00C0 0x0408 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS 0x00C0 0x0408 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW2__UART5_DTE_RTS 0x00C0 0x0408 0x084C 0x2 0x3
#define MX6SX_PAD_KEY_ROW2__CAN1_RX 0x00C0 0x0408 0x068C 0x3 0x1
#define MX6SX_PAD_KEY_ROW2__CANFD_RX1 0x00C0 0x0408 0x0694 0x4 0x1
#define MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x00C0 0x0408 0x0000 0x5 0x0
@@ -441,8 +455,8 @@
#define MX6SX_PAD_KEY_ROW2__ECSPI1_SS3 0x00C0 0x0408 0x0000 0x7 0x0
#define MX6SX_PAD_KEY_ROW3__KPP_ROW_3 0x00C4 0x040C 0x0000 0x0 0x0
#define MX6SX_PAD_KEY_ROW3__USDHC3_LCTL 0x00C4 0x040C 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW3__UART5_RX 0x00C4 0x040C 0x0850 0x2 0x3
-#define MX6SX_PAD_KEY_ROW3__UART5_TX 0x00C4 0x040C 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW3__UART5_DCE_RX 0x00C4 0x040C 0x0850 0x2 0x3
+#define MX6SX_PAD_KEY_ROW3__UART5_DTE_TX 0x00C4 0x040C 0x0000 0x2 0x0
#define MX6SX_PAD_KEY_ROW3__CAN2_RX 0x00C4 0x040C 0x0690 0x3 0x1
#define MX6SX_PAD_KEY_ROW3__CANFD_RX2 0x00C4 0x040C 0x0698 0x4 0x1
#define MX6SX_PAD_KEY_ROW3__GPIO2_IO_18 0x00C4 0x040C 0x0000 0x5 0x0
@@ -815,7 +829,8 @@
#define MX6SX_PAD_NAND_DATA04__RAWNAND_DATA04 0x0160 0x04A8 0x0000 0x0 0x0
#define MX6SX_PAD_NAND_DATA04__USDHC2_DATA4 0x0160 0x04A8 0x0000 0x1 0x0
#define MX6SX_PAD_NAND_DATA04__QSPI2_B_SS1_B 0x0160 0x04A8 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA04__UART3_RTS_B 0x0160 0x04A8 0x083C 0x3 0x0
+#define MX6SX_PAD_NAND_DATA04__UART3_DCE_RTS 0x0160 0x04A8 0x083C 0x3 0x0
+#define MX6SX_PAD_NAND_DATA04__UART3_DTE_CTS 0x0160 0x04A8 0x0000 0x3 0x0
#define MX6SX_PAD_NAND_DATA04__AUDMUX_AUD4_RXFS 0x0160 0x04A8 0x0650 0x4 0x0
#define MX6SX_PAD_NAND_DATA04__GPIO4_IO_8 0x0160 0x04A8 0x0000 0x5 0x0
#define MX6SX_PAD_NAND_DATA04__WEIM_AD_4 0x0160 0x04A8 0x0000 0x6 0x0
@@ -825,7 +840,8 @@
#define MX6SX_PAD_NAND_DATA05__RAWNAND_DATA05 0x0164 0x04AC 0x0000 0x0 0x0
#define MX6SX_PAD_NAND_DATA05__USDHC2_DATA5 0x0164 0x04AC 0x0000 0x1 0x0
#define MX6SX_PAD_NAND_DATA05__QSPI2_B_DQS 0x0164 0x04AC 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA05__UART3_CTS_B 0x0164 0x04AC 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA05__UART3_DCE_CTS 0x0164 0x04AC 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA05__UART3_DTE_RTS 0x0164 0x04AC 0x083C 0x3 0x1
#define MX6SX_PAD_NAND_DATA05__AUDMUX_AUD4_RXC 0x0164 0x04AC 0x064C 0x4 0x0
#define MX6SX_PAD_NAND_DATA05__GPIO4_IO_9 0x0164 0x04AC 0x0000 0x5 0x0
#define MX6SX_PAD_NAND_DATA05__WEIM_AD_5 0x0164 0x04AC 0x0000 0x6 0x0
@@ -835,8 +851,8 @@
#define MX6SX_PAD_NAND_DATA06__RAWNAND_DATA06 0x0168 0x04B0 0x0000 0x0 0x0
#define MX6SX_PAD_NAND_DATA06__USDHC2_DATA6 0x0168 0x04B0 0x0000 0x1 0x0
#define MX6SX_PAD_NAND_DATA06__QSPI2_A_SS1_B 0x0168 0x04B0 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA06__UART3_RX 0x0168 0x04B0 0x0840 0x3 0x0
-#define MX6SX_PAD_NAND_DATA06__UART3_TX 0x0168 0x04B0 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA06__UART3_DCE_RX 0x0168 0x04B0 0x0840 0x3 0x0
+#define MX6SX_PAD_NAND_DATA06__UART3_DTE_TX 0x0168 0x04B0 0x0000 0x3 0x0
#define MX6SX_PAD_NAND_DATA06__PWM3_OUT 0x0168 0x04B0 0x0000 0x4 0x0
#define MX6SX_PAD_NAND_DATA06__GPIO4_IO_10 0x0168 0x04B0 0x0000 0x5 0x0
#define MX6SX_PAD_NAND_DATA06__WEIM_AD_6 0x0168 0x04B0 0x0000 0x6 0x0
@@ -846,8 +862,8 @@
#define MX6SX_PAD_NAND_DATA07__RAWNAND_DATA07 0x016C 0x04B4 0x0000 0x0 0x0
#define MX6SX_PAD_NAND_DATA07__USDHC2_DATA7 0x016C 0x04B4 0x0000 0x1 0x0
#define MX6SX_PAD_NAND_DATA07__QSPI2_A_DQS 0x016C 0x04B4 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA07__UART3_RX 0x016C 0x04B4 0x0840 0x3 0x1
-#define MX6SX_PAD_NAND_DATA07__UART3_TX 0x016C 0x04B4 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA07__UART3_DCE_TX 0x016C 0x04B4 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA07__UART3_DTE_RX 0x016C 0x04B4 0x0840 0x3 0x1
#define MX6SX_PAD_NAND_DATA07__PWM4_OUT 0x016C 0x04B4 0x0000 0x4 0x0
#define MX6SX_PAD_NAND_DATA07__GPIO4_IO_11 0x016C 0x04B4 0x0000 0x5 0x0
#define MX6SX_PAD_NAND_DATA07__WEIM_AD_7 0x016C 0x04B4 0x0000 0x6 0x0
@@ -967,7 +983,8 @@
#define MX6SX_PAD_QSPI1A_SS1_B__SIM_M_HADDR_12 0x019C 0x04E4 0x0000 0x7 0x0
#define MX6SX_PAD_QSPI1A_SS1_B__SDMA_DEBUG_PC_3 0x019C 0x04E4 0x0000 0x9 0x0
#define MX6SX_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 0x01A0 0x04E8 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_DATA0__UART3_CTS_B 0x01A0 0x04E8 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_DCE_CTS 0x01A0 0x04E8 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_DTE_RTS 0x01A0 0x04E8 0x083C 0x1 0x4
#define MX6SX_PAD_QSPI1B_DATA0__ECSPI3_MOSI 0x01A0 0x04E8 0x0738 0x2 0x1
#define MX6SX_PAD_QSPI1B_DATA0__ESAI_RX_FS 0x01A0 0x04E8 0x0778 0x3 0x2
#define MX6SX_PAD_QSPI1B_DATA0__CSI1_DATA_22 0x01A0 0x04E8 0x06F4 0x4 0x1
@@ -975,7 +992,8 @@
#define MX6SX_PAD_QSPI1B_DATA0__WEIM_DATA_14 0x01A0 0x04E8 0x0000 0x6 0x0
#define MX6SX_PAD_QSPI1B_DATA0__SIM_M_HADDR_9 0x01A0 0x04E8 0x0000 0x7 0x0
#define MX6SX_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 0x01A4 0x04EC 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_DATA1__UART3_RTS_B 0x01A4 0x04EC 0x083C 0x1 0x5
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_DCE_RTS 0x01A4 0x04EC 0x083C 0x1 0x5
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_DTE_CTS 0x01A4 0x04EC 0x0000 0x1 0x0
#define MX6SX_PAD_QSPI1B_DATA1__ECSPI3_MISO 0x01A4 0x04EC 0x0734 0x2 0x1
#define MX6SX_PAD_QSPI1B_DATA1__ESAI_RX_CLK 0x01A4 0x04EC 0x0788 0x3 0x2
#define MX6SX_PAD_QSPI1B_DATA1__CSI1_DATA_21 0x01A4 0x04EC 0x06F0 0x4 0x1
@@ -1007,8 +1025,8 @@
#define MX6SX_PAD_QSPI1B_DQS__WEIM_DATA_15 0x01B0 0x04F8 0x0000 0x6 0x0
#define MX6SX_PAD_QSPI1B_DQS__SIM_M_HADDR_15 0x01B0 0x04F8 0x0000 0x7 0x0
#define MX6SX_PAD_QSPI1B_SCLK__QSPI1_B_SCLK 0x01B4 0x04FC 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_SCLK__UART3_RX 0x01B4 0x04FC 0x0840 0x1 0x4
-#define MX6SX_PAD_QSPI1B_SCLK__UART3_TX 0x01B4 0x04FC 0x0000 0x0 0x0
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX 0x01B4 0x04FC 0x0840 0x1 0x4
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_DTE_TX 0x01B4 0x04FC 0x0000 0x1 0x0
#define MX6SX_PAD_QSPI1B_SCLK__ECSPI3_SCLK 0x01B4 0x04FC 0x0730 0x2 0x1
#define MX6SX_PAD_QSPI1B_SCLK__ESAI_RX_HF_CLK 0x01B4 0x04FC 0x0780 0x3 0x2
#define MX6SX_PAD_QSPI1B_SCLK__CSI1_DATA_16 0x01B4 0x04FC 0x06DC 0x4 0x1
@@ -1016,8 +1034,8 @@
#define MX6SX_PAD_QSPI1B_SCLK__WEIM_DATA_8 0x01B4 0x04FC 0x0000 0x6 0x0
#define MX6SX_PAD_QSPI1B_SCLK__SIM_M_HADDR_11 0x01B4 0x04FC 0x0000 0x7 0x0
#define MX6SX_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B 0x01B8 0x0500 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_SS0_B__UART3_RX 0x01B8 0x0500 0x0840 0x1 0x5
-#define MX6SX_PAD_QSPI1B_SS0_B__UART3_TX 0x01B8 0x0500 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX 0x01B8 0x0500 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_DTE_RX 0x01B8 0x0500 0x0840 0x1 0x5
#define MX6SX_PAD_QSPI1B_SS0_B__ECSPI3_SS0 0x01B8 0x0500 0x073C 0x2 0x1
#define MX6SX_PAD_QSPI1B_SS0_B__ESAI_TX_HF_CLK 0x01B8 0x0500 0x0784 0x3 0x3
#define MX6SX_PAD_QSPI1B_SS0_B__CSI1_DATA_17 0x01B8 0x0500 0x06E0 0x4 0x1
@@ -1224,8 +1242,8 @@
#define MX6SX_PAD_SD1_DATA0__AUDMUX_AUD5_RXD 0x0228 0x0570 0x065C 0x1 0x1
#define MX6SX_PAD_SD1_DATA0__CAAM_WRAPPER_RNG_OSC_OBS 0x0228 0x0570 0x0000 0x2 0x0
#define MX6SX_PAD_SD1_DATA0__GPT_CAPTURE1 0x0228 0x0570 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA0__UART2_RX 0x0228 0x0570 0x0838 0x4 0x2
-#define MX6SX_PAD_SD1_DATA0__UART2_TX 0x0228 0x0570 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA0__UART2_DCE_RX 0x0228 0x0570 0x0838 0x4 0x2
+#define MX6SX_PAD_SD1_DATA0__UART2_DTE_TX 0x0228 0x0570 0x0000 0x4 0x0
#define MX6SX_PAD_SD1_DATA0__GPIO6_IO_2 0x0228 0x0570 0x0000 0x5 0x0
#define MX6SX_PAD_SD1_DATA0__ENET1_1588_EVENT1_IN 0x0228 0x0570 0x0000 0x6 0x0
#define MX6SX_PAD_SD1_DATA0__CCM_OUT2 0x0228 0x0570 0x0000 0x7 0x0
@@ -1235,8 +1253,8 @@
#define MX6SX_PAD_SD1_DATA1__AUDMUX_AUD5_TXC 0x022C 0x0574 0x066C 0x1 0x1
#define MX6SX_PAD_SD1_DATA1__PWM4_OUT 0x022C 0x0574 0x0000 0x2 0x0
#define MX6SX_PAD_SD1_DATA1__GPT_CAPTURE2 0x022C 0x0574 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA1__UART2_RX 0x022C 0x0574 0x0838 0x4 0x3
-#define MX6SX_PAD_SD1_DATA1__UART2_TX 0x022C 0x0574 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA1__UART2_DCE_TX 0x022C 0x0574 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA1__UART2_DTE_RX 0x022C 0x0574 0x0838 0x4 0x3
#define MX6SX_PAD_SD1_DATA1__GPIO6_IO_3 0x022C 0x0574 0x0000 0x5 0x0
#define MX6SX_PAD_SD1_DATA1__ENET1_1588_EVENT1_OUT 0x022C 0x0574 0x0000 0x6 0x0
#define MX6SX_PAD_SD1_DATA1__CCM_CLKO2 0x022C 0x0574 0x0000 0x7 0x0
@@ -1246,7 +1264,8 @@
#define MX6SX_PAD_SD1_DATA2__AUDMUX_AUD5_TXFS 0x0230 0x0578 0x0670 0x1 0x1
#define MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x0230 0x0578 0x0000 0x2 0x0
#define MX6SX_PAD_SD1_DATA2__GPT_COMPARE2 0x0230 0x0578 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA2__UART2_CTS_B 0x0230 0x0578 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA2__UART2_DCE_CTS 0x0230 0x0578 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA2__UART2_DTE_RTS 0x0230 0x0578 0x0834 0x4 0x2
#define MX6SX_PAD_SD1_DATA2__GPIO6_IO_4 0x0230 0x0578 0x0000 0x5 0x0
#define MX6SX_PAD_SD1_DATA2__ECSPI4_RDY 0x0230 0x0578 0x0000 0x6 0x0
#define MX6SX_PAD_SD1_DATA2__CCM_OUT0 0x0230 0x0578 0x0000 0x7 0x0
@@ -1255,7 +1274,8 @@
#define MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_TXD 0x0234 0x057C 0x0660 0x1 0x1
#define MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_RXD 0x0234 0x057C 0x065C 0x2 0x2
#define MX6SX_PAD_SD1_DATA3__GPT_COMPARE3 0x0234 0x057C 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA3__UART2_RTS_B 0x0234 0x057C 0x0834 0x4 0x3
+#define MX6SX_PAD_SD1_DATA3__UART2_DCE_RTS 0x0234 0x057C 0x0834 0x4 0x3
+#define MX6SX_PAD_SD1_DATA3__UART2_DTE_CTS 0x0234 0x057C 0x0000 0x4 0x0
#define MX6SX_PAD_SD1_DATA3__GPIO6_IO_5 0x0234 0x057C 0x0000 0x5 0x0
#define MX6SX_PAD_SD1_DATA3__ECSPI4_SS1 0x0234 0x057C 0x0000 0x6 0x0
#define MX6SX_PAD_SD1_DATA3__CCM_PMIC_RDY 0x0234 0x057C 0x069C 0x7 0x2
@@ -1287,8 +1307,8 @@
#define MX6SX_PAD_SD2_DATA0__I2C4_SDA 0x0240 0x0588 0x07C4 0x4 0x3
#define MX6SX_PAD_SD2_DATA0__GPIO6_IO_8 0x0240 0x0588 0x0000 0x5 0x0
#define MX6SX_PAD_SD2_DATA0__ECSPI4_SS3 0x0240 0x0588 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA0__UART4_RX 0x0240 0x0588 0x0848 0x7 0x4
-#define MX6SX_PAD_SD2_DATA0__UART4_TX 0x0240 0x0588 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA0__UART4_DCE_RX 0x0240 0x0588 0x0848 0x7 0x4
+#define MX6SX_PAD_SD2_DATA0__UART4_DTE_TX 0x0240 0x0588 0x0000 0x7 0x0
#define MX6SX_PAD_SD2_DATA0__VADC_CLAMP_CURRENT_0 0x0240 0x0588 0x0000 0x8 0x0
#define MX6SX_PAD_SD2_DATA0__MMDC_DEBUG_50 0x0240 0x0588 0x0000 0x9 0x0
#define MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x0244 0x058C 0x0000 0x0 0x0
@@ -1298,8 +1318,8 @@
#define MX6SX_PAD_SD2_DATA1__I2C4_SCL 0x0244 0x058C 0x07C0 0x4 0x3
#define MX6SX_PAD_SD2_DATA1__GPIO6_IO_9 0x0244 0x058C 0x0000 0x5 0x0
#define MX6SX_PAD_SD2_DATA1__ECSPI4_SS2 0x0244 0x058C 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA1__UART4_RX 0x0244 0x058C 0x0848 0x7 0x5
-#define MX6SX_PAD_SD2_DATA1__UART4_TX 0x0244 0x058C 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA1__UART4_DCE_TX 0x0244 0x058C 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA1__UART4_DTE_RX 0x0244 0x058C 0x0848 0x7 0x5
#define MX6SX_PAD_SD2_DATA1__VADC_CLAMP_CURRENT_1 0x0244 0x058C 0x0000 0x8 0x0
#define MX6SX_PAD_SD2_DATA1__MMDC_DEBUG_49 0x0244 0x058C 0x0000 0x9 0x0
#define MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x0248 0x0590 0x0000 0x0 0x0
@@ -1309,8 +1329,8 @@
#define MX6SX_PAD_SD2_DATA2__SDMA_EXT_EVENT_0 0x0248 0x0590 0x081C 0x4 0x2
#define MX6SX_PAD_SD2_DATA2__GPIO6_IO_10 0x0248 0x0590 0x0000 0x5 0x0
#define MX6SX_PAD_SD2_DATA2__SPDIF_OUT 0x0248 0x0590 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA2__UART6_RX 0x0248 0x0590 0x0858 0x7 0x4
-#define MX6SX_PAD_SD2_DATA2__UART6_TX 0x0248 0x0590 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA2__UART6_DCE_RX 0x0248 0x0590 0x0858 0x7 0x4
+#define MX6SX_PAD_SD2_DATA2__UART6_DTE_TX 0x0248 0x0590 0x0000 0x7 0x0
#define MX6SX_PAD_SD2_DATA2__VADC_CLAMP_CURRENT_2 0x0248 0x0590 0x0000 0x8 0x0
#define MX6SX_PAD_SD2_DATA2__MMDC_DEBUG_32 0x0248 0x0590 0x0000 0x9 0x0
#define MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x024C 0x0594 0x0000 0x0 0x0
@@ -1320,12 +1340,13 @@
#define MX6SX_PAD_SD2_DATA3__MLB_DATA 0x024C 0x0594 0x07EC 0x4 0x2
#define MX6SX_PAD_SD2_DATA3__GPIO6_IO_11 0x024C 0x0594 0x0000 0x5 0x0
#define MX6SX_PAD_SD2_DATA3__SPDIF_IN 0x024C 0x0594 0x0824 0x6 0x4
-#define MX6SX_PAD_SD2_DATA3__UART6_RX 0x024C 0x0594 0x0858 0x7 0x5
-#define MX6SX_PAD_SD2_DATA3__UART6_TX 0x024C 0x0594 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA3__UART6_DCE_TX 0x024C 0x0594 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA3__UART6_DTE_RX 0x024C 0x0594 0x0858 0x7 0x5
#define MX6SX_PAD_SD2_DATA3__VADC_CLAMP_CURRENT_3 0x024C 0x0594 0x0000 0x8 0x0
#define MX6SX_PAD_SD2_DATA3__MMDC_DEBUG_31 0x024C 0x0594 0x0000 0x9 0x0
#define MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x0250 0x0598 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_CLK__UART4_CTS_B 0x0250 0x0598 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CLK__UART4_DCE_CTS 0x0250 0x0598 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CLK__UART4_DTE_RTS 0x0250 0x0598 0x0844 0x1 0x0
#define MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x0250 0x0598 0x0740 0x2 0x0
#define MX6SX_PAD_SD3_CLK__AUDMUX_AUD6_RXFS 0x0250 0x0598 0x0680 0x3 0x0
#define MX6SX_PAD_SD3_CLK__LCDIF2_VSYNC 0x0250 0x0598 0x0000 0x4 0x0
@@ -1334,8 +1355,8 @@
#define MX6SX_PAD_SD3_CLK__TPSMP_HDATA_29 0x0250 0x0598 0x0000 0x7 0x0
#define MX6SX_PAD_SD3_CLK__SDMA_DEBUG_EVENT_CHANNEL_5 0x0250 0x0598 0x0000 0x9 0x0
#define MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x0254 0x059C 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_CMD__UART4_RX 0x0254 0x059C 0x0848 0x1 0x0
-#define MX6SX_PAD_SD3_CMD__UART4_TX 0x0254 0x059C 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CMD__UART4_DCE_TX 0x0254 0x059C 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CMD__UART4_DTE_RX 0x0254 0x059C 0x0848 0x1 0x0
#define MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x0254 0x059C 0x0748 0x2 0x0
#define MX6SX_PAD_SD3_CMD__AUDMUX_AUD6_RXC 0x0254 0x059C 0x067C 0x3 0x0
#define MX6SX_PAD_SD3_CMD__LCDIF2_HSYNC 0x0254 0x059C 0x07E4 0x4 0x1
@@ -1364,7 +1385,8 @@
#define MX6SX_PAD_SD3_DATA1__GPU_DEBUG_1 0x025C 0x05A4 0x0000 0x8 0x0
#define MX6SX_PAD_SD3_DATA1__SDMA_DEBUG_EVT_CHN_LINES_1 0x025C 0x05A4 0x0000 0x9 0x0
#define MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x0260 0x05A8 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_DATA2__UART4_RTS_B 0x0260 0x05A8 0x0844 0x1 0x1
+#define MX6SX_PAD_SD3_DATA2__UART4_DCE_RTS 0x0260 0x05A8 0x0844 0x1 0x1
+#define MX6SX_PAD_SD3_DATA2__UART4_DTE_CTS 0x0260 0x05A8 0x0000 0x1 0x0
#define MX6SX_PAD_SD3_DATA2__ECSPI4_SS0 0x0260 0x05A8 0x074C 0x2 0x0
#define MX6SX_PAD_SD3_DATA2__AUDMUX_AUD6_TXFS 0x0260 0x05A8 0x0688 0x3 0x0
#define MX6SX_PAD_SD3_DATA2__LCDIF2_CLK 0x0260 0x05A8 0x0000 0x4 0x0
@@ -1374,8 +1396,8 @@
#define MX6SX_PAD_SD3_DATA2__GPU_DEBUG_2 0x0260 0x05A8 0x0000 0x8 0x0
#define MX6SX_PAD_SD3_DATA2__SDMA_DEBUG_EVENT_CHANNEL_2 0x0260 0x05A8 0x0000 0x9 0x0
#define MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x0264 0x05AC 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_DATA3__UART4_RX 0x0264 0x05AC 0x0848 0x1 0x1
-#define MX6SX_PAD_SD3_DATA3__UART4_TX 0x0264 0x05AC 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_DATA3__UART4_DCE_RX 0x0264 0x05AC 0x0848 0x1 0x1
+#define MX6SX_PAD_SD3_DATA3__UART4_DTE_TX 0x0264 0x05AC 0x0000 0x1 0x0
#define MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x0264 0x05AC 0x0744 0x2 0x0
#define MX6SX_PAD_SD3_DATA3__AUDMUX_AUD6_TXD 0x0264 0x05AC 0x0678 0x3 0x0
#define MX6SX_PAD_SD3_DATA3__LCDIF2_ENABLE 0x0264 0x05AC 0x0000 0x4 0x0
@@ -1387,8 +1409,8 @@
#define MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x0268 0x05B0 0x0000 0x0 0x0
#define MX6SX_PAD_SD3_DATA4__CAN2_RX 0x0268 0x05B0 0x0690 0x1 0x0
#define MX6SX_PAD_SD3_DATA4__CANFD_RX2 0x0268 0x05B0 0x0698 0x2 0x0
-#define MX6SX_PAD_SD3_DATA4__UART3_RX 0x0268 0x05B0 0x0840 0x3 0x2
-#define MX6SX_PAD_SD3_DATA4__UART3_TX 0x0268 0x05B0 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA4__UART3_DCE_RX 0x0268 0x05B0 0x0840 0x3 0x2
+#define MX6SX_PAD_SD3_DATA4__UART3_DTE_TX 0x0268 0x05B0 0x0000 0x3 0x0
#define MX6SX_PAD_SD3_DATA4__LCDIF2_DATA_3 0x0268 0x05B0 0x0000 0x4 0x0
#define MX6SX_PAD_SD3_DATA4__GPIO7_IO_6 0x0268 0x05B0 0x0000 0x5 0x0
#define MX6SX_PAD_SD3_DATA4__ENET2_1588_EVENT0_IN 0x0268 0x05B0 0x0000 0x6 0x0
@@ -1398,8 +1420,8 @@
#define MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x026C 0x05B4 0x0000 0x0 0x0
#define MX6SX_PAD_SD3_DATA5__CAN1_TX 0x026C 0x05B4 0x0000 0x1 0x0
#define MX6SX_PAD_SD3_DATA5__CANFD_TX1 0x026C 0x05B4 0x0000 0x2 0x0
-#define MX6SX_PAD_SD3_DATA5__UART3_RX 0x026C 0x05B4 0x0840 0x3 0x3
-#define MX6SX_PAD_SD3_DATA5__UART3_TX 0x026C 0x05B4 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA5__UART3_DCE_TX 0x026C 0x05B4 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA5__UART3_DTE_RX 0x026C 0x05B4 0x0840 0x3 0x3
#define MX6SX_PAD_SD3_DATA5__LCDIF2_DATA_2 0x026C 0x05B4 0x0000 0x4 0x0
#define MX6SX_PAD_SD3_DATA5__GPIO7_IO_7 0x026C 0x05B4 0x0000 0x5 0x0
#define MX6SX_PAD_SD3_DATA5__ENET2_1588_EVENT0_OUT 0x026C 0x05B4 0x0000 0x6 0x0
@@ -1409,7 +1431,8 @@
#define MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x0270 0x05B8 0x0000 0x0 0x0
#define MX6SX_PAD_SD3_DATA6__CAN2_TX 0x0270 0x05B8 0x0000 0x1 0x0
#define MX6SX_PAD_SD3_DATA6__CANFD_TX2 0x0270 0x05B8 0x0000 0x2 0x0
-#define MX6SX_PAD_SD3_DATA6__UART3_RTS_B 0x0270 0x05B8 0x083C 0x3 0x2
+#define MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS 0x0270 0x05B8 0x083C 0x3 0x2
+#define MX6SX_PAD_SD3_DATA6__UART3_DTE_CTS 0x0270 0x05B8 0x0000 0x3 0x0
#define MX6SX_PAD_SD3_DATA6__LCDIF2_DATA_4 0x0270 0x05B8 0x0000 0x4 0x0
#define MX6SX_PAD_SD3_DATA6__GPIO7_IO_8 0x0270 0x05B8 0x0000 0x5 0x0
#define MX6SX_PAD_SD3_DATA6__ENET1_1588_EVENT0_OUT 0x0270 0x05B8 0x0000 0x6 0x0
@@ -1419,7 +1442,8 @@
#define MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x0274 0x05BC 0x0000 0x0 0x0
#define MX6SX_PAD_SD3_DATA7__CAN1_RX 0x0274 0x05BC 0x068C 0x1 0x0
#define MX6SX_PAD_SD3_DATA7__CANFD_RX1 0x0274 0x05BC 0x0694 0x2 0x0
-#define MX6SX_PAD_SD3_DATA7__UART3_CTS_B 0x0274 0x05BC 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS 0x0274 0x05BC 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA7__UART3_DTE_RTS 0x0274 0x05BC 0x083C 0x3 0x3
#define MX6SX_PAD_SD3_DATA7__LCDIF2_DATA_5 0x0274 0x05BC 0x0000 0x4 0x0
#define MX6SX_PAD_SD3_DATA7__GPIO7_IO_9 0x0274 0x05BC 0x0000 0x5 0x0
#define MX6SX_PAD_SD3_DATA7__ENET1_1588_EVENT0_IN 0x0274 0x05BC 0x0000 0x6 0x0
@@ -1488,8 +1512,8 @@
#define MX6SX_PAD_SD4_DATA3__SDMA_DEBUG_MATCHED_DMBUS 0x028C 0x05D4 0x0000 0x9 0x0
#define MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x0290 0x05D8 0x0000 0x0 0x0
#define MX6SX_PAD_SD4_DATA4__RAWNAND_DATA09 0x0290 0x05D8 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA4__UART5_RX 0x0290 0x05D8 0x0850 0x2 0x0
-#define MX6SX_PAD_SD4_DATA4__UART5_TX 0x0290 0x05D8 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA4__UART5_DCE_RX 0x0290 0x05D8 0x0850 0x2 0x0
+#define MX6SX_PAD_SD4_DATA4__UART5_DTE_TX 0x0290 0x05D8 0x0000 0x2 0x0
#define MX6SX_PAD_SD4_DATA4__ECSPI3_SCLK 0x0290 0x05D8 0x0730 0x3 0x0
#define MX6SX_PAD_SD4_DATA4__LCDIF2_DATA_8 0x0290 0x05D8 0x0000 0x4 0x0
#define MX6SX_PAD_SD4_DATA4__GPIO6_IO_18 0x0290 0x05D8 0x0000 0x5 0x0
@@ -1499,8 +1523,8 @@
#define MX6SX_PAD_SD4_DATA4__SDMA_DEBUG_RTBUFFER_WRITE 0x0290 0x05D8 0x0000 0x9 0x0
#define MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x0294 0x05DC 0x0000 0x0 0x0
#define MX6SX_PAD_SD4_DATA5__RAWNAND_CE2_B 0x0294 0x05DC 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA5__UART5_RX 0x0294 0x05DC 0x0850 0x2 0x1
-#define MX6SX_PAD_SD4_DATA5__UART5_TX 0x0294 0x05DC 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA5__UART5_DCE_TX 0x0294 0x05DC 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA5__UART5_DTE_RX 0x0294 0x05DC 0x0850 0x2 0x1
#define MX6SX_PAD_SD4_DATA5__ECSPI3_MOSI 0x0294 0x05DC 0x0738 0x3 0x0
#define MX6SX_PAD_SD4_DATA5__LCDIF2_DATA_7 0x0294 0x05DC 0x0000 0x4 0x0
#define MX6SX_PAD_SD4_DATA5__GPIO6_IO_19 0x0294 0x05DC 0x0000 0x5 0x0
@@ -1510,7 +1534,8 @@
#define MX6SX_PAD_SD4_DATA5__SDMA_DEBUG_EVENT_CHANNEL_0 0x0294 0x05DC 0x0000 0x9 0x0
#define MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x0298 0x05E0 0x0000 0x0 0x0
#define MX6SX_PAD_SD4_DATA6__RAWNAND_CE3_B 0x0298 0x05E0 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA6__UART5_RTS_B 0x0298 0x05E0 0x084C 0x2 0x0
+#define MX6SX_PAD_SD4_DATA6__UART5_DCE_RTS 0x0298 0x05E0 0x084C 0x2 0x0
+#define MX6SX_PAD_SD4_DATA6__UART5_DTE_CTS 0x0298 0x05E0 0x0000 0x2 0x0
#define MX6SX_PAD_SD4_DATA6__ECSPI3_MISO 0x0298 0x05E0 0x0734 0x3 0x0
#define MX6SX_PAD_SD4_DATA6__LCDIF2_DATA_6 0x0298 0x05E0 0x0000 0x4 0x0
#define MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x0298 0x05E0 0x0000 0x5 0x0
@@ -1520,7 +1545,8 @@
#define MX6SX_PAD_SD4_DATA6__SDMA_DEBUG_EVENT_CHANNEL_1 0x0298 0x05E0 0x0000 0x9 0x0
#define MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x029C 0x05E4 0x0000 0x0 0x0
#define MX6SX_PAD_SD4_DATA7__RAWNAND_DATA08 0x029C 0x05E4 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA7__UART5_CTS_B 0x029C 0x05E4 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA7__UART5_DCE_CTS 0x029C 0x05E4 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA7__UART5_DTE_RTS 0x029C 0x05E4 0x084C 0x2 0x1
#define MX6SX_PAD_SD4_DATA7__ECSPI3_SS0 0x029C 0x05E4 0x073C 0x3 0x0
#define MX6SX_PAD_SD4_DATA7__LCDIF2_DATA_15 0x029C 0x05E4 0x0000 0x4 0x0
#define MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x029C 0x05E4 0x0000 0x5 0x0
@@ -1551,4 +1577,92 @@
#define MX6SX_PAD_USB_H_STROBE__WDOG3_WDOG_RST_B_DEB 0x02A8 0x05F0 0x0000 0x4 0x0
#define MX6SX_PAD_USB_H_STROBE__GPIO7_IO_11 0x02A8 0x05F0 0x0000 0x5 0x0
+/* these are not supposed to be used any more and remove them after some time */
+#define MX6SX_PAD_GPIO1_IO04__UART1_RX MX6SX_PAD_GPIO1_IO04__UART1_DTE_RX
+#define MX6SX_PAD_GPIO1_IO04__UART1_TX MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX
+#define MX6SX_PAD_GPIO1_IO05__UART1_RX MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX
+#define MX6SX_PAD_GPIO1_IO05__UART1_TX MX6SX_PAD_GPIO1_IO05__UART1_DTE_TX
+#define MX6SX_PAD_GPIO1_IO06__UART2_RX MX6SX_PAD_GPIO1_IO06__UART2_DTE_RX
+#define MX6SX_PAD_GPIO1_IO06__UART2_TX MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX
+#define MX6SX_PAD_GPIO1_IO06__UART1_RTS_B MX6SX_PAD_GPIO1_IO06__UART1_DCE_RTS
+#define MX6SX_PAD_GPIO1_IO07__UART2_RX MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX
+#define MX6SX_PAD_GPIO1_IO07__UART2_TX MX6SX_PAD_GPIO1_IO07__UART2_DTE_TX
+#define MX6SX_PAD_GPIO1_IO07__UART1_CTS_B MX6SX_PAD_GPIO1_IO07__UART1_DCE_CTS
+#define MX6SX_PAD_GPIO1_IO08__UART2_RTS_B MX6SX_PAD_GPIO1_IO08__UART2_DCE_RTS
+#define MX6SX_PAD_GPIO1_IO09__UART2_CTS_B MX6SX_PAD_GPIO1_IO09__UART2_DCE_CTS
+#define MX6SX_PAD_CSI_DATA04__UART6_RX MX6SX_PAD_CSI_DATA04__UART6_DCE_RX
+#define MX6SX_PAD_CSI_DATA04__UART6_TX MX6SX_PAD_CSI_DATA04__UART6_DTE_TX
+#define MX6SX_PAD_CSI_DATA05__UART6_RX MX6SX_PAD_CSI_DATA05__UART6_DTE_RX
+#define MX6SX_PAD_CSI_DATA05__UART6_TX MX6SX_PAD_CSI_DATA05__UART6_DCE_TX
+#define MX6SX_PAD_CSI_DATA06__UART6_RTS_B MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS
+#define MX6SX_PAD_CSI_DATA07__UART6_CTS_B MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS
+#define MX6SX_PAD_CSI_HSYNC__UART4_RTS_B MX6SX_PAD_CSI_HSYNC__UART4_DCE_RTS
+#define MX6SX_PAD_CSI_MCLK__UART4_RX MX6SX_PAD_CSI_MCLK__UART4_DCE_RX
+#define MX6SX_PAD_CSI_MCLK__UART4_TX MX6SX_PAD_CSI_MCLK__UART4_DTE_TX
+#define MX6SX_PAD_CSI_PIXCLK__UART4_RX MX6SX_PAD_CSI_PIXCLK__UART4_DTE_RX
+#define MX6SX_PAD_CSI_PIXCLK__UART4_TX MX6SX_PAD_CSI_PIXCLK__UART4_DCE_TX
+#define MX6SX_PAD_CSI_VSYNC__UART4_CTS_B MX6SX_PAD_CSI_VSYNC__UART4_DCE_CTS
+#define MX6SX_PAD_ENET2_COL__UART1_RX MX6SX_PAD_ENET2_COL__UART1_DCE_RX
+#define MX6SX_PAD_ENET2_COL__UART1_TX MX6SX_PAD_ENET2_COL__UART1_DTE_TX
+#define MX6SX_PAD_ENET2_CRS__UART1_RX MX6SX_PAD_ENET2_CRS__UART1_DTE_RX
+#define MX6SX_PAD_ENET2_CRS__UART1_TX MX6SX_PAD_ENET2_CRS__UART1_DCE_TX
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_RTS_B MX6SX_PAD_ENET2_RX_CLK__UART1_DCE_RTS
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_CTS_B MX6SX_PAD_ENET2_TX_CLK__UART1_DCE_CTS
+#define MX6SX_PAD_KEY_COL0__UART6_RTS_B MX6SX_PAD_KEY_COL0__UART6_DCE_RTS
+#define MX6SX_PAD_KEY_COL1__UART6_RX MX6SX_PAD_KEY_COL1__UART6_DTE_RX
+#define MX6SX_PAD_KEY_COL1__UART6_TX MX6SX_PAD_KEY_COL1__UART6_DCE_TX
+#define MX6SX_PAD_KEY_COL2__UART5_RTS_B MX6SX_PAD_KEY_COL2__UART5_DCE_RTS
+#define MX6SX_PAD_KEY_COL3__UART5_RX MX6SX_PAD_KEY_COL3__UART5_DTE_RX
+#define MX6SX_PAD_KEY_COL3__UART5_TX MX6SX_PAD_KEY_COL3__UART5_DCE_TX
+#define MX6SX_PAD_KEY_ROW0__UART6_CTS_B MX6SX_PAD_KEY_ROW0__UART6_DCE_CTS
+#define MX6SX_PAD_KEY_ROW1__UART6_RX MX6SX_PAD_KEY_ROW1__UART6_DCE_RX
+#define MX6SX_PAD_KEY_ROW1__UART6_TX MX6SX_PAD_KEY_ROW1__UART6_DTE_TX
+#define MX6SX_PAD_KEY_ROW2__UART5_CTS_B MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS
+#define MX6SX_PAD_KEY_ROW3__UART5_RX MX6SX_PAD_KEY_ROW3__UART5_DCE_RX
+#define MX6SX_PAD_KEY_ROW3__UART5_TX MX6SX_PAD_KEY_ROW3__UART5_DTE_TX
+#define MX6SX_PAD_NAND_DATA04__UART3_RTS_B MX6SX_PAD_NAND_DATA04__UART3_DCE_RTS
+#define MX6SX_PAD_NAND_DATA05__UART3_CTS_B MX6SX_PAD_NAND_DATA05__UART3_DCE_CTS
+#define MX6SX_PAD_NAND_DATA06__UART3_RX MX6SX_PAD_NAND_DATA06__UART3_DCE_RX
+#define MX6SX_PAD_NAND_DATA06__UART3_TX MX6SX_PAD_NAND_DATA06__UART3_DTE_TX
+#define MX6SX_PAD_NAND_DATA07__UART3_RX MX6SX_PAD_NAND_DATA07__UART3_DTE_RX
+#define MX6SX_PAD_NAND_DATA07__UART3_TX MX6SX_PAD_NAND_DATA07__UART3_DCE_TX
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_CTS_B MX6SX_PAD_QSPI1B_DATA0__UART3_DCE_CTS
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_RTS_B MX6SX_PAD_QSPI1B_DATA1__UART3_DCE_RTS
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_RX MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_TX MX6SX_PAD_QSPI1B_SCLK__UART3_DTE_TX
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_RX MX6SX_PAD_QSPI1B_SS0_B__UART3_DTE_RX
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_TX MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX
+#define MX6SX_PAD_SD1_DATA0__UART2_RX MX6SX_PAD_SD1_DATA0__UART2_DCE_RX
+#define MX6SX_PAD_SD1_DATA0__UART2_TX MX6SX_PAD_SD1_DATA0__UART2_DTE_TX
+#define MX6SX_PAD_SD1_DATA1__UART2_RX MX6SX_PAD_SD1_DATA1__UART2_DTE_RX
+#define MX6SX_PAD_SD1_DATA1__UART2_TX MX6SX_PAD_SD1_DATA1__UART2_DCE_TX
+#define MX6SX_PAD_SD1_DATA2__UART2_CTS_B MX6SX_PAD_SD1_DATA2__UART2_DCE_CTS
+#define MX6SX_PAD_SD1_DATA3__UART2_RTS_B MX6SX_PAD_SD1_DATA3__UART2_DCE_RTS
+#define MX6SX_PAD_SD2_DATA0__UART4_RX MX6SX_PAD_SD2_DATA0__UART4_DCE_RX
+#define MX6SX_PAD_SD2_DATA0__UART4_TX MX6SX_PAD_SD2_DATA0__UART4_DTE_TX
+#define MX6SX_PAD_SD2_DATA1__UART4_RX MX6SX_PAD_SD2_DATA1__UART4_DTE_RX
+#define MX6SX_PAD_SD2_DATA1__UART4_TX MX6SX_PAD_SD2_DATA1__UART4_DCE_TX
+#define MX6SX_PAD_SD2_DATA2__UART6_RX MX6SX_PAD_SD2_DATA2__UART6_DCE_RX
+#define MX6SX_PAD_SD2_DATA2__UART6_TX MX6SX_PAD_SD2_DATA2__UART6_DTE_TX
+#define MX6SX_PAD_SD2_DATA3__UART6_RX MX6SX_PAD_SD2_DATA3__UART6_DTE_RX
+#define MX6SX_PAD_SD2_DATA3__UART6_TX MX6SX_PAD_SD2_DATA3__UART6_DCE_TX
+#define MX6SX_PAD_SD3_CLK__UART4_CTS_B MX6SX_PAD_SD3_CLK__UART4_DCE_CTS
+#define MX6SX_PAD_SD3_CMD__UART4_RX MX6SX_PAD_SD3_CMD__UART4_DTE_RX
+#define MX6SX_PAD_SD3_CMD__UART4_TX MX6SX_PAD_SD3_CMD__UART4_DCE_TX
+#define MX6SX_PAD_SD3_DATA2__UART4_RTS_B MX6SX_PAD_SD3_DATA2__UART4_DCE_RTS
+#define MX6SX_PAD_SD3_DATA3__UART4_RX MX6SX_PAD_SD3_DATA3__UART4_DCE_RX
+#define MX6SX_PAD_SD3_DATA3__UART4_TX MX6SX_PAD_SD3_DATA3__UART4_DTE_TX
+#define MX6SX_PAD_SD3_DATA4__UART3_RX MX6SX_PAD_SD3_DATA4__UART3_DCE_RX
+#define MX6SX_PAD_SD3_DATA4__UART3_TX MX6SX_PAD_SD3_DATA4__UART3_DTE_TX
+#define MX6SX_PAD_SD3_DATA5__UART3_RX MX6SX_PAD_SD3_DATA5__UART3_DTE_RX
+#define MX6SX_PAD_SD3_DATA5__UART3_TX MX6SX_PAD_SD3_DATA5__UART3_DCE_TX
+#define MX6SX_PAD_SD3_DATA6__UART3_RTS_B MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS
+#define MX6SX_PAD_SD3_DATA7__UART3_CTS_B MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS
+#define MX6SX_PAD_SD4_DATA4__UART5_RX MX6SX_PAD_SD4_DATA4__UART5_DCE_RX
+#define MX6SX_PAD_SD4_DATA4__UART5_TX MX6SX_PAD_SD4_DATA4__UART5_DTE_TX
+#define MX6SX_PAD_SD4_DATA5__UART5_RX MX6SX_PAD_SD4_DATA5__UART5_DTE_RX
+#define MX6SX_PAD_SD4_DATA5__UART5_TX MX6SX_PAD_SD4_DATA5__UART5_DCE_TX
+#define MX6SX_PAD_SD4_DATA6__UART5_RTS_B MX6SX_PAD_SD4_DATA6__UART5_DCE_RTS
+#define MX6SX_PAD_SD4_DATA7__UART5_CTS_B MX6SX_PAD_SD4_DATA7__UART5_DCE_CTS
+
#endif /* __DTS_IMX6SX_PINFUNC_H */
diff --git a/arch/arm/dts/imx6sx-udoo-neo-basic.dts b/arch/arm/dts/imx6sx-udoo-neo-basic.dts
new file mode 100644
index 0000000000..205ea26484
--- /dev/null
+++ b/arch/arm/dts/imx6sx-udoo-neo-basic.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas F?rber
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+ model = "UDOO Neo Basic";
+ compatible = "udoo,neobasic", "fsl,imx6sx";
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+};
+
+&fec1 {
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+ };
+};
diff --git a/arch/arm/dts/imx6sx-udoo-neo-extended.dts b/arch/arm/dts/imx6sx-udoo-neo-extended.dts
new file mode 100644
index 0000000000..5817b49853
--- /dev/null
+++ b/arch/arm/dts/imx6sx-udoo-neo-extended.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas F?rber
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+ model = "UDOO Neo Extended";
+ compatible = "udoo,neoextended", "fsl,imx6sx";
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+};
+
+&i2c4 { /* Onboard Motion sensors */
+ status = "okay";
+};
+
+&uart3 { /* Bluetooth */
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6sx-udoo-neo-full.dts b/arch/arm/dts/imx6sx-udoo-neo-full.dts
new file mode 100644
index 0000000000..96f4d89848
--- /dev/null
+++ b/arch/arm/dts/imx6sx-udoo-neo-full.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas F?rber
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+ model = "UDOO Neo Full";
+ compatible = "udoo,neofull", "fsl,imx6sx";
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+};
+
+&fec1 {
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+ };
+};
+
+&i2c4 { /* Onboard Motion sensors */
+ status = "okay";
+};
+
+&uart3 { /* Bluetooth */
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6sx-udoo-neo.dtsi b/arch/arm/dts/imx6sx-udoo-neo.dtsi
new file mode 100644
index 0000000000..ee64565509
--- /dev/null
+++ b/arch/arm/dts/imx6sx-udoo-neo.dtsi
@@ -0,0 +1,410 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas F?rber
+ */
+
+#include "imx6sx.dtsi"
+
+/ {
+ compatible = "fsl,imx6sx";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ red {
+ label = "udoo-neo:red:mmc";
+ gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "mmc0";
+ };
+
+ orange {
+ label = "udoo-neo:orange:user";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+ };
+
+ reg_sdio_pwr: regulator-sdio-pwr {
+ compatible = "regulator-fixed";
+ gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "SDIO_PWR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_otg1_reg>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_otg2_reg>;
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_wlan: regulator-wlan {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-reset-duration = <10>;
+ phy-reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ pmic: pmic at 8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c2 { /* Brick snap in sensors connector */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c4 { /* Onboard Motion sensors */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ clock-frequency = <100000>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_bt_reg: btreggrp {
+ fsl,pins =
+ <MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x15059>;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins =
+ <MX6SX_PAD_ENET1_CRS__GPIO2_IO_1 0xa0b1>,
+ <MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1>,
+ <MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1>,
+ <MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1>,
+ <MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1>,
+ <MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1>,
+
+ <MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x3081>,
+ <MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9 0x3081>,
+ <MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081>,
+ <MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081>,
+ <MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081>,
+ <MX6SX_PAD_RGMII1_RXC__ENET1_RX_ER 0x3081>,
+
+ <MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91>;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1>,
+ <MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1>;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO03__I2C2_SDA 0x4001b8b1>,
+ <MX6SX_PAD_GPIO1_IO02__I2C2_SCL 0x4001b8b1>;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins =
+ <MX6SX_PAD_USB_H_DATA__I2C4_SDA 0x4001b8b1>,
+ <MX6SX_PAD_USB_H_STROBE__I2C4_SCL 0x4001b8b1>;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX 0x1b0b1>,
+ <MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX 0x1b0b1>;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX 0x1b0b1>,
+ <MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX 0x1b0b1>;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins =
+ <MX6SX_PAD_SD3_DATA4__UART3_DCE_RX 0x13059>,
+ <MX6SX_PAD_SD3_DATA5__UART3_DCE_TX 0x13059>,
+ <MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS 0x13059>,
+ <MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS 0x13059>;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins =
+ <MX6SX_PAD_SD4_DATA4__UART5_DCE_RX 0x1b0b1>,
+ <MX6SX_PAD_SD4_DATA5__UART5_DCE_TX 0x1b0b1>;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins =
+ <MX6SX_PAD_CSI_DATA00__UART6_RI_B 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA01__UART6_DSR_B 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA02__UART6_DTR_B 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA03__UART6_DCD_B 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA04__UART6_DCE_RX 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA05__UART6_DCE_TX 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS 0x1b0b1>,
+ <MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS 0x1b0b1>;
+ };
+
+ pinctrl_otg1_reg: otg1grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0>;
+ };
+
+
+ pinctrl_otg2_reg: otg2grp {
+ fsl,pins =
+ <MX6SX_PAD_NAND_RE_B__GPIO4_IO_12 0x10b0>;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins =
+ <MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059>,
+ <MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC 0x10b0>;
+ };
+
+ pinctrl_usb_otg2: usbot2ggrp {
+ fsl,pins =
+ <MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC 0x10b0>;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins =
+ <MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059>,
+ <MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059>,
+ <MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059>,
+ <MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059>,
+ <MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059>,
+ <MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059>,
+ <MX6SX_PAD_SD1_DATA0__GPIO6_IO_2 0x17059>; /* CD */
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins =
+ <MX6SX_PAD_KEY_COL2__GPIO2_IO_12 0x15059>,
+ <MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x13059>,
+ <MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17069>,
+ <MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17069>,
+ <MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17069>,
+ <MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17069>,
+ <MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17069>,
+ <MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10069>,
+ <MX6SX_PAD_CSI_MCLK__OSC32K_32K_OUT 0x10059>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+/* Cortex-M4 serial */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "disabled";
+};
+
+&uart3 { /* Bluetooth - only on Extended/Full versions */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "disabled";
+
+ bluetooth {
+ compatible = "ti,wl1831-st";
+ enable-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_bt_reg>;
+ max-speed = <921600>;
+ };
+};
+
+/* Arduino serial */
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "disabled";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ uart-has-rtscts;
+ status = "disabled";
+};
+
+&usbotg1 { /* J2 micro USB port */
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ status = "okay";
+};
+
+&usbotg2 { /* J3 host USB port */
+ vbus-supply = <®_usb_otg2_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg2>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ vmmc-supply = <®_sdio_pwr>;
+ bus-width = <4>;
+ cd-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc3 { /* Wi-Fi */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ non-removable;
+ vmmc-supply = <®_wlan>;
+ cap-power-off-card;
+ wakeup-source;
+ keep-power-in-suspend;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore at 2 {
+ compatible = "ti,wl1831";
+ reg = <2>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+ ref-clock-frequency = <38400000>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
@ 2021-04-01 20:08 ` Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-01 20:08 ` [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC Peter Robinson
` (4 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Peter Robinson @ 2021-04-01 20:08 UTC (permalink / raw)
To: u-boot
Enable OF_CONTROL and DM for gpio and pin control support
on the i.MX6SX based Udoo Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
configs/udoo_neo_defconfig | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
index ba1e6d31f8..44ca8cfc3d 100644
--- a/configs/udoo_neo_defconfig
+++ b/configs/udoo_neo_defconfig
@@ -5,10 +5,13 @@ CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="imx6sx-udoo-neo-basic"
+CONFIG_OF_LIST="imx6sx-udoo-neo-basic imx6sx-udoo-neo-extended imx6sx-udoo-neo-full"
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0x80000
CONFIG_MX6SX=y
CONFIG_TARGET_UDOO_NEO=y
+CONFIG_OF_CONTROL=y
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
@@ -26,13 +29,18 @@ CONFIG_CMD_GPIO=y
CONFIG_CMD_MMC=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_CACHE=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_BOUNCE_BUFFER=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
CONFIG_FSL_USDHC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
2021-04-01 20:08 ` [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control Peter Robinson
@ 2021-04-01 20:08 ` Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-01 20:08 ` [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM Peter Robinson
` (3 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Peter Robinson @ 2021-04-01 20:08 UTC (permalink / raw)
To: u-boot
Convert UDOO Neo to use DM MMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
arch/arm/dts/imx6sx-udoo-neo-u-boot.dtsi | 7 +++++
board/udoo/neo/neo.c | 39 ------------------------
configs/udoo_neo_defconfig | 1 +
3 files changed, 8 insertions(+), 39 deletions(-)
create mode 100644 arch/arm/dts/imx6sx-udoo-neo-u-boot.dtsi
diff --git a/arch/arm/dts/imx6sx-udoo-neo-u-boot.dtsi b/arch/arm/dts/imx6sx-udoo-neo-u-boot.dtsi
new file mode 100644
index 0000000000..daf2489cfd
--- /dev/null
+++ b/arch/arm/dts/imx6sx-udoo-neo-u-boot.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/ {
+ aliases {
+ mmc0 = &usdhc2;
+ };
+};
diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
index 653ca1ca5a..ef7de0aacc 100644
--- a/board/udoo/neo/neo.c
+++ b/board/udoo/neo/neo.c
@@ -19,8 +19,6 @@
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <env.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/mach-imx/mxc_i2c.h>
@@ -218,19 +216,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- /* CD pin */
- MX6_PAD_SD1_DATA0__GPIO6_IO_2 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* Power */
- MX6_PAD_SD1_CMD__GPIO6_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const fec1_pads[] = {
MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -393,30 +378,6 @@ int board_early_init_f(void)
return 0;
}
-static struct fsl_esdhc_cfg usdhc_cfg[1] = {
- {USDHC2_BASE_ADDR, 0, 4},
-};
-
-#define USDHC2_PWR_GPIO IMX_GPIO_NR(6, 1)
-#define USDHC2_CD_GPIO IMX_GPIO_NR(6, 2)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- return !gpio_get_value(USDHC2_CD_GPIO);
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- gpio_direction_input(USDHC2_CD_GPIO);
- gpio_direction_output(USDHC2_PWR_GPIO, 1);
-
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-}
-
static char *board_string(void)
{
switch (get_board_value()) {
diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
index 44ca8cfc3d..3df2ac19e7 100644
--- a/configs/udoo_neo_defconfig
+++ b/configs/udoo_neo_defconfig
@@ -38,6 +38,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM=y
CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
CONFIG_FSL_USDHC=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
2021-04-01 20:08 ` [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control Peter Robinson
2021-04-01 20:08 ` [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC Peter Robinson
@ 2021-04-01 20:08 ` Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-03 14:11 ` [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Fabio Estevam
` (2 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Peter Robinson @ 2021-04-01 20:08 UTC (permalink / raw)
To: u-boot
Convert the UDOO Neo to ethernet DM support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
board/udoo/neo/neo.c | 63 +++-----------------------------------
configs/udoo_neo_defconfig | 3 ++
include/configs/udoo_neo.h | 10 ------
3 files changed, 7 insertions(+), 69 deletions(-)
diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
index ef7de0aacc..92a1e084b5 100644
--- a/board/udoo/neo/neo.c
+++ b/board/udoo/neo/neo.c
@@ -9,7 +9,6 @@
*/
#include <init.h>
-#include <net.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
@@ -18,6 +17,7 @@
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
+#include <dm.h>
#include <env.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
@@ -28,8 +28,6 @@
#include <linux/sizes.h>
#include <common.h>
#include <i2c.h>
-#include <miiphy.h>
-#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include <malloc.h>
@@ -216,21 +214,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
-static iomux_v3_cfg_t const fec1_pads[] = {
- MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_ENET2_TX_CLK__GPIO2_IO_9 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_ENET1_CRS__GPIO2_IO_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const phy_control_pads[] = {
/* 25MHz Ethernet PHY Clock */
MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M |
@@ -257,7 +240,7 @@ static void setup_iomux_uart(void)
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
-static int setup_fec(int fec_id)
+static int setup_fec(void)
{
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
int reg;
@@ -275,46 +258,7 @@ static int setup_fec(int fec_id)
reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE;
writel(reg, &anatop->pll_enet);
- return enable_fec_anatop_clock(fec_id, ENET_25MHZ);
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- uint32_t base = IMX_FEC_BASE;
- struct mii_dev *bus = NULL;
- struct phy_device *phydev = NULL;
- int ret;
-
- imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-
- setup_fec(CONFIG_FEC_ENET_DEV);
-
- bus = fec_get_miibus(base, CONFIG_FEC_ENET_DEV);
- if (!bus)
- return -EINVAL;
-
- phydev = phy_find_by_mask(bus, (0x1 << CONFIG_FEC_MXC_PHYADDR),
- PHY_INTERFACE_MODE_RMII);
- if (!phydev) {
- free(bus);
- return -EINVAL;
- }
-
- ret = fec_probe(bis, CONFIG_FEC_ENET_DEV, base, bus, phydev);
- if (ret) {
- free(bus);
- free(phydev);
- return ret;
- }
- return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
+ return enable_fec_anatop_clock(0, ENET_25MHZ);
}
int board_init(void)
@@ -374,6 +318,7 @@ static int get_board_value(void)
int board_early_init_f(void)
{
setup_iomux_uart();
+ setup_fec();
return 0;
}
diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
index 3df2ac19e7..a9b2e5bc1d 100644
--- a/configs/udoo_neo_defconfig
+++ b/configs/udoo_neo_defconfig
@@ -37,6 +37,8 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_FSL_USDHC=y
@@ -46,6 +48,7 @@ CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
CONFIG_MII=y
+CONFIG_RGMII=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
CONFIG_OF_LIBFDT=y
diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
index 4935a2b363..b6f75c9262 100644
--- a/include/configs/udoo_neo.h
+++ b/include/configs/udoo_neo.h
@@ -83,14 +83,4 @@
#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
#define PFUZE3000_I2C_BUS 0
-/* Network */
-#define CONFIG_FEC_MXC
-
-#define CONFIG_FEC_ENET_DEV 0
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR 0x0
-
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC0"
-
#endif /* __CONFIG_H */
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
` (2 preceding siblings ...)
2021-04-01 20:08 ` [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM Peter Robinson
@ 2021-04-03 14:11 ` Fabio Estevam
2021-04-08 20:59 ` sbabic at denx.de
2021-04-22 15:31 ` Tom Rini
5 siblings, 0 replies; 10+ messages in thread
From: Fabio Estevam @ 2021-04-03 14:11 UTC (permalink / raw)
To: u-boot
Hi Peter,
On Thu, Apr 1, 2021 at 5:08 PM Peter Robinson <pbrobinson@gmail.com> wrote:
>
> Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
> and sync the i.MX6SX pinfunc.h
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
Thanks for working on the DM conversion.
For the whole series:
Reviewed-by: Fabio Estevam <festevam@gmail.com>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
` (3 preceding siblings ...)
2021-04-03 14:11 ` [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Fabio Estevam
@ 2021-04-08 20:59 ` sbabic at denx.de
2021-04-22 15:31 ` Tom Rini
5 siblings, 0 replies; 10+ messages in thread
From: sbabic at denx.de @ 2021-04-08 20:59 UTC (permalink / raw)
To: u-boot
> Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
> and sync the i.MX6SX pinfunc.h
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
` (4 preceding siblings ...)
2021-04-08 20:59 ` sbabic at denx.de
@ 2021-04-22 15:31 ` Tom Rini
5 siblings, 0 replies; 10+ messages in thread
From: Tom Rini @ 2021-04-22 15:31 UTC (permalink / raw)
To: u-boot
On Thu, Apr 01, 2021 at 09:08:10PM +0100, Peter Robinson wrote:
> Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
> and sync the i.MX6SX pinfunc.h
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Note that Stefano said this was applied to u-boot-imx/master, but it
wasn't there and I think got missed with udoo and udoo_neo being
separate series. So, I've picked this up directly.
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210422/d342b258/attachment.sig>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control
2021-04-01 20:08 ` [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control Peter Robinson
@ 2021-04-22 15:31 ` Tom Rini
0 siblings, 0 replies; 10+ messages in thread
From: Tom Rini @ 2021-04-22 15:31 UTC (permalink / raw)
To: u-boot
On Thu, Apr 01, 2021 at 09:08:11PM +0100, Peter Robinson wrote:
> Enable OF_CONTROL and DM for gpio and pin control support
> on the i.MX6SX based Udoo Neo.
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210422/97de6a36/attachment.sig>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC
2021-04-01 20:08 ` [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC Peter Robinson
@ 2021-04-22 15:31 ` Tom Rini
0 siblings, 0 replies; 10+ messages in thread
From: Tom Rini @ 2021-04-22 15:31 UTC (permalink / raw)
To: u-boot
On Thu, Apr 01, 2021 at 09:08:12PM +0100, Peter Robinson wrote:
> Convert UDOO Neo to use DM MMC.
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210422/e7fc90bd/attachment.sig>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM
2021-04-01 20:08 ` [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM Peter Robinson
@ 2021-04-22 15:31 ` Tom Rini
0 siblings, 0 replies; 10+ messages in thread
From: Tom Rini @ 2021-04-22 15:31 UTC (permalink / raw)
To: u-boot
On Thu, Apr 01, 2021 at 09:08:13PM +0100, Peter Robinson wrote:
> Convert the UDOO Neo to ethernet DM support.
>
> Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
> Cc: Breno Lima <breno.lima@nxp.com>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210422/a9008157/attachment.sig>
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2021-04-22 15:31 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-01 20:08 [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Peter Robinson
2021-04-01 20:08 ` [PATCH 2/4] ARM: imx: udoo_neo: Enable OF_CONTROL and DM gpio/pin control Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-01 20:08 ` [PATCH 3/4] ARM: imx: udoo_neo: convert to DM_MMC Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-01 20:08 ` [PATCH 4/4] ARM: imx: udoo_neo: Convert to ethernet DM Peter Robinson
2021-04-22 15:31 ` Tom Rini
2021-04-03 14:11 ` [PATCH 1/4] ARM: board: udoo_neo: Import UDOO Neo dts files Fabio Estevam
2021-04-08 20:59 ` sbabic at denx.de
2021-04-22 15:31 ` Tom Rini
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.