* [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers
@ 2021-04-23 10:19 Sean Nyekjaer
2021-04-23 10:19 ` [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings Sean Nyekjaer
2021-04-23 12:51 ` [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Andy Shevchenko
0 siblings, 2 replies; 7+ messages in thread
From: Sean Nyekjaer @ 2021-04-23 10:19 UTC (permalink / raw)
To: jic23, linux-iio, andy.shevchenko, lars, Nuno.Sa, robh+dt, devicetree
Cc: Sean Nyekjaer
Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
accelerometers.
It will allow setting up scale/gain and reading x,y,z
axis.
Datasheets for the devices can be found here:
https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
---
Changes for v2:
- Addressed Kconfig comments
- Using regmap_read_poll_timeout()
- Addresed comments from Andy and Jonathan
drivers/iio/accel/Kconfig | 27 ++
drivers/iio/accel/Makefile | 3 +
drivers/iio/accel/fxls8962af-core.c | 620 ++++++++++++++++++++++++++++
drivers/iio/accel/fxls8962af-i2c.c | 57 +++
drivers/iio/accel/fxls8962af-spi.c | 57 +++
drivers/iio/accel/fxls8962af.h | 21 +
6 files changed, 785 insertions(+)
create mode 100644 drivers/iio/accel/fxls8962af-core.c
create mode 100644 drivers/iio/accel/fxls8962af-i2c.c
create mode 100644 drivers/iio/accel/fxls8962af-spi.c
create mode 100644 drivers/iio/accel/fxls8962af.h
diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
index 2e0c62c39155..902f2e2edf65 100644
--- a/drivers/iio/accel/Kconfig
+++ b/drivers/iio/accel/Kconfig
@@ -208,6 +208,33 @@ config DMARD10
Choosing M will build the driver as a module. If so, the module
will be called dmard10.
+config FXLS8962AF
+ tristate
+
+config FXLS8962AF_I2C
+ tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver"
+ depends on I2C
+ select REGMAP_I2C
+ select FXLS8962AF
+ help
+ Say yes here to build support for the NXP 3-axis automotive
+ accelerometer FXLS8962AF/FXLS8964AF with I2C support.
+
+ To compile this driver as a module, choose M here: the module
+ will be called fxls8962af_i2c.
+
+config FXLS8962AF_SPI
+ tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver"
+ depends on SPI
+ select FXLS8962AF
+ select REGMAP_SPI
+ help
+ Say yes here to build support for the NXP 3-axis automotive
+ accelerometer FXLS8962AF/FXLS8964AF with SPI support.
+
+ To compile this driver as a module, choose M here: the module
+ will be called fxls8962af_spi.
+
config HID_SENSOR_ACCEL_3D
depends on HID_SENSOR_HUB
select IIO_BUFFER
diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
index 4f6c1ebe13b0..1b8c479c6f7c 100644
--- a/drivers/iio/accel/Makefile
+++ b/drivers/iio/accel/Makefile
@@ -25,6 +25,9 @@ obj-$(CONFIG_DA311) += da311.o
obj-$(CONFIG_DMARD06) += dmard06.o
obj-$(CONFIG_DMARD09) += dmard09.o
obj-$(CONFIG_DMARD10) += dmard10.o
+obj-$(CONFIG_FXLS8962AF) += fxls8962af-core.o
+obj-$(CONFIG_FXLS8962AF_I2C) += fxls8962af-i2c.o
+obj-$(CONFIG_FXLS8962AF_SPI) += fxls8962af-spi.o
obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
obj-$(CONFIG_KXSD9) += kxsd9.o
diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
new file mode 100644
index 000000000000..6fda3bc1f28f
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-core.c
@@ -0,0 +1,620 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NXP FXLS8962AF/FXLS8964AF Accelerometer Core Driver
+ *
+ * Copyright 2021 Connected Cars A/S
+ *
+ * Datasheet:
+ * https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
+ * https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
+ */
+
+#include <linux/bits.h>
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#include "fxls8962af.h"
+
+#define FXLS8962AF_INT_STATUS 0x00
+#define FXLS8962AF_INT_STATUS_SRC_DRDY BIT(7)
+#define FXLS8962AF_TEMP_OUT 0x01
+#define FXLS8962AF_VECM_LSB 0x02
+#define FXLS8962AF_OUT_X_LSB 0x04
+#define FXLS8962AF_OUT_Y_LSB 0x06
+#define FXLS8962AF_OUT_Z_LSB 0x08
+#define FXLS8962AF_BUF_STATUS 0x0b
+#define FXLS8962AF_BUF_X_LSB 0x0c
+#define FXLS8962AF_BUF_Y_LSB 0x0e
+#define FXLS8962AF_BUF_Z_LSB 0x10
+
+#define FXLS8962AF_PROD_REV 0x12
+#define FXLS8962AF_WHO_AM_I 0x13
+
+#define FXLS8962AF_SYS_MODE 0x14
+#define FXLS8962AF_SENS_CONFIG1 0x15
+#define FXLS8962AF_SENS_CONFIG1_ACTIVE BIT(0)
+#define FXLS8962AF_SENS_CONFIG1_RST BIT(7)
+#define FXLS8962AF_SC1_FSR_MASK GENMASK(2, 1)
+#define FXLS8962AF_SC1_FSR_PREP(x) FIELD_PREP(FXLS8962AF_SC1_FSR_MASK, x)
+#define FXLS8962AF_SC1_FSR_GET(x) FIELD_GET(FXLS8962AF_SC1_FSR_MASK, x)
+
+#define FXLS8962AF_SENS_CONFIG2 0x16
+#define FXLS8962AF_SENS_CONFIG3 0x17
+#define FXLS8962AF_SENS_CONFIG4 0x18
+#define FXLS8962AF_SENS_CONFIG5 0x19
+
+#define FXLS8962AF_WAKE_IDLE_LSB 0x1b
+#define FXLS8962AF_SLEEP_IDLE_LSB 0x1c
+#define FXLS8962AF_ASLP_COUNT_LSB 0x1e
+
+#define FXLS8962AF_INT_EN 0x20
+#define FXLS8962AF_INT_PIN_SEL 0x21
+
+#define FXLS8962AF_OFF_X 0x22
+#define FXLS8962AF_OFF_Y 0x23
+#define FXLS8962AF_OFF_Z 0x24
+
+#define FXLS8962AF_BUF_CONFIG1 0x26
+#define FXLS8962AF_BUF_CONFIG2 0x27
+
+#define FXLS8962AF_ORIENT_STATUS 0x28
+#define FXLS8962AF_ORIENT_CONFIG 0x29
+#define FXLS8962AF_ORIENT_DBCOUNT 0x2a
+#define FXLS8962AF_ORIENT_BF_ZCOMP 0x2b
+#define FXLS8962AF_ORIENT_THS_REG 0x2c
+
+#define FXLS8962AF_SDCD_INT_SRC1 0x2d
+#define FXLS8962AF_SDCD_INT_SRC2 0x2e
+#define FXLS8962AF_SDCD_CONFIG1 0x2f
+#define FXLS8962AF_SDCD_CONFIG2 0x30
+#define FXLS8962AF_SDCD_OT_DBCNT 0x31
+#define FXLS8962AF_SDCD_WT_DBCNT 0x32
+#define FXLS8962AF_SDCD_LTHS_LSB 0x33
+#define FXLS8962AF_SDCD_UTHS_LSB 0x35
+
+#define FXLS8962AF_SELF_TEST_CONFIG1 0x37
+#define FXLS8962AF_SELF_TEST_CONFIG2 0x38
+
+#define FXLS8962AF_MAX_REG 0x38
+
+#define FXLS8962AF_DEVICE_ID 0x62
+#define FXLS8964AF_DEVICE_ID 0x84
+
+/*Raw temp channel offset */
+#define FXLS8962AF_TEMP_CENTER_VAL 25
+
+#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS 2000
+
+#define FXLS8962AF_SCALE_TABLE_LEN 4
+
+static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
+ {0, IIO_G_TO_M_S_2(980000)},
+ {0, IIO_G_TO_M_S_2(1950000)},
+ {0, IIO_G_TO_M_S_2(3910000)},
+ {0, IIO_G_TO_M_S_2(7810000)},
+};
+
+struct fxls8962af_chip_info {
+ const char *name;
+ const struct iio_chan_spec *channels;
+ int num_channels;
+ u8 chip_id;
+};
+
+struct fxls8962af_data {
+ struct regmap *regmap;
+ const struct fxls8962af_chip_info *chip_info;
+ struct regulator *vdd_reg;
+ struct iio_mount_matrix orientation;
+};
+
+const struct regmap_config fxls8962af_regmap_conf = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = FXLS8962AF_MAX_REG,
+};
+EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
+
+enum {
+ fxls8962af_idx_x,
+ fxls8962af_idx_y,
+ fxls8962af_idx_z,
+ fxls8962af_idx_ts,
+};
+
+static int fxls8962af_drdy(struct fxls8962af_data *data)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_INT_STATUS, reg,
+ (reg & FXLS8962AF_INT_STATUS_SRC_DRDY), 20000, 2000000);
+ if (ret) {
+ dev_err(dev, "drdy timeout, int_status = 0x%x\n", reg);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int fxls8962af_power_on(struct fxls8962af_data *data)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ int ret;
+
+ ret = pm_runtime_get_sync(dev);
+
+ if (ret < 0) {
+ dev_err(dev, "failed to power on\n");
+ pm_runtime_put_noidle(dev);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int fxls8962af_power_off(struct fxls8962af_data *data)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ int ret;
+
+ pm_runtime_mark_last_busy(dev);
+ ret = pm_runtime_put_autosuspend(dev);
+
+ if (ret < 0) {
+ dev_err(dev, "failed to power off\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int fxls8962af_get_temp(struct fxls8962af_data *data, int *val)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ int ret;
+ unsigned int value;
+
+ ret = fxls8962af_drdy(data);
+ if (ret < 0)
+ return ret;
+
+ ret = fxls8962af_power_on(data);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(data->regmap, FXLS8962AF_TEMP_OUT, &value);
+ if (ret < 0) {
+ dev_err(dev, "Error reading reg_temp\n");
+ fxls8962af_power_off(data);
+ return ret;
+ }
+
+ fxls8962af_power_off(data);
+
+ *val = sign_extend32(value, 7);
+
+ return IIO_VAL_INT;
+}
+
+static int fxls8962af_get_axis(struct fxls8962af_data *data,
+ struct iio_chan_spec const *chan, int *val)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ int ret;
+ __le16 raw_val;
+
+ ret = fxls8962af_drdy(data);
+ if (ret < 0)
+ return ret;
+
+ ret = fxls8962af_power_on(data);
+ if (ret)
+ return ret;
+
+ ret = regmap_bulk_read(data->regmap, chan->address,
+ &raw_val, sizeof(raw_val));
+ if (ret < 0) {
+ dev_err(dev, "failed to read axes\n");
+ fxls8962af_power_off(data);
+ return ret;
+ }
+
+ fxls8962af_power_off(data);
+
+ *val = sign_extend32(le16_to_cpu(raw_val), chan->scan_type.realbits - 1);
+
+ return IIO_VAL_INT;
+}
+
+static int fxls8962af_read_avail(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ const int **vals, int *type, int *length,
+ long mask)
+{
+ switch (mask) {
+ case IIO_CHAN_INFO_SCALE:
+ *type = IIO_VAL_INT_PLUS_NANO;
+ *vals = (int *)fxls8962af_scale_table;
+ *length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ long mask)
+{
+ return IIO_VAL_INT_PLUS_NANO;
+}
+
+static int fxls8962af_standby(struct fxls8962af_data *data)
+{
+ return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+ FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
+}
+
+static int fxls8962af_active(struct fxls8962af_data *data)
+{
+ return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+ FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
+}
+
+static int fxls8962af_is_active(struct fxls8962af_data *data)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
+ if (ret < 0)
+ return ret;
+
+ return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
+}
+
+static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
+ u8 mask, u8 val)
+{
+ int ret;
+ int is_active;
+
+ is_active = fxls8962af_is_active(data);
+ if (is_active) {
+ ret = fxls8962af_standby(data);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = regmap_update_bits(data->regmap, reg, mask, val);
+ if (ret < 0)
+ return ret;
+
+ if (is_active) {
+ ret = fxls8962af_active(data);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
+ if (scale == fxls8962af_scale_table[i][1])
+ break;
+
+ if (i == ARRAY_SIZE(fxls8962af_scale_table))
+ return -EINVAL;
+
+ return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
+ FXLS8962AF_SC1_FSR_MASK,
+ FXLS8962AF_SC1_FSR_PREP(i));
+}
+
+static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
+ int *val)
+{
+ int ret;
+ unsigned int reg;
+ u8 range_idx;
+
+ ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
+ if (ret < 0)
+ return ret;
+
+ range_idx = FXLS8962AF_SC1_FSR_GET(reg);
+
+ *val = fxls8962af_scale_table[range_idx][1];
+
+ return IIO_VAL_INT_PLUS_NANO;
+}
+
+static int fxls8962af_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ ret = iio_device_claim_direct_mode(indio_dev);
+ if (ret)
+ return ret;
+
+ switch (chan->type) {
+ case IIO_TEMP:
+ ret = fxls8962af_get_temp(data, val);
+ break;
+ case IIO_ACCEL:
+ ret = fxls8962af_get_axis(data, chan, val);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ iio_device_release_direct_mode(indio_dev);
+ return ret;
+ case IIO_CHAN_INFO_OFFSET:
+ if (chan->type == IIO_TEMP) {
+ *val = FXLS8962AF_TEMP_CENTER_VAL;
+ return IIO_VAL_INT;
+ }
+ break;
+ case IIO_CHAN_INFO_SCALE:
+ *val = 0;
+ return fxls8962af_read_full_scale(data, val2);
+ default:
+ return -EINVAL;
+ }
+
+ return -EINVAL;
+}
+
+static int fxls8962af_write_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ struct fxls8962af_data *data = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_SCALE:
+ if (val != 0)
+ return -EINVAL;
+
+ ret = iio_device_claim_direct_mode(indio_dev);
+ if (ret)
+ return ret;
+
+ ret = fxls8962af_set_full_scale(data, val2);
+
+ iio_device_release_direct_mode(indio_dev);
+ return ret;
+ default:
+ return -EINVAL;
+ }
+
+ return -EINVAL;
+}
+
+#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
+ .type = IIO_ACCEL, \
+ .address = reg, \
+ .modified = 1, \
+ .channel2 = IIO_MOD_##axis, \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
+ .info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
+ .scan_index = idx, \
+ .scan_type = { \
+ .sign = 's', \
+ .realbits = 12, \
+ .storagebits = 16, \
+ .shift = 4, \
+ .endianness = IIO_BE, \
+ }, \
+}
+
+#define FXLS8962AF_TEMP_CHANNEL { \
+ .type = IIO_TEMP, \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_OFFSET),\
+ .scan_index = -1, \
+ .scan_type = { \
+ .realbits = 8, \
+ }, \
+}
+
+static const struct iio_chan_spec fxls8962af_channels[] = {
+ FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
+ FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
+ FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
+ IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
+ FXLS8962AF_TEMP_CHANNEL,
+};
+
+static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
+ [fxls8962af] = {
+ .chip_id = FXLS8962AF_DEVICE_ID,
+ .name = "fxls8962af",
+ .channels = fxls8962af_channels,
+ .num_channels = ARRAY_SIZE(fxls8962af_channels),
+ },
+ [fxls8964af] = {
+ .chip_id = FXLS8964AF_DEVICE_ID,
+ .name = "fxls8964af",
+ .channels = fxls8962af_channels,
+ .num_channels = ARRAY_SIZE(fxls8962af_channels),
+ },
+};
+
+static const struct iio_info fxls8962af_info = {
+ .read_raw = &fxls8962af_read_raw,
+ .write_raw = &fxls8962af_write_raw,
+ .write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
+ .read_avail = fxls8962af_read_avail,
+};
+
+static int fxls8962af_reset(struct fxls8962af_data *data)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
+ FXLS8962AF_SENS_CONFIG1_RST,
+ FXLS8962AF_SENS_CONFIG1_RST);
+ if (ret < 0)
+ return ret;
+
+ /* TBOOT1, TBOOT2, specifies we have to wait between 1 - 17.7ms */
+ ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_SENS_CONFIG1, reg,
+ !(reg & FXLS8962AF_SENS_CONFIG1_RST), 1000, 18000);
+ if (ret) {
+ dev_err(dev, "reset timeout, sens_config1 = 0x%x\n", reg);
+ return ret;
+ }
+
+ return ret;
+}
+
+static void fxls8962af_regulator_disable(void *data_ptr)
+{
+ struct fxls8962af_data *data = data_ptr;
+
+ regulator_disable(data->vdd_reg);
+}
+
+static void fxls8962af_pm_disable(void *dev_ptr)
+{
+ struct device *dev = dev_ptr;
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_put_noidle(dev);
+
+ fxls8962af_standby(iio_priv(indio_dev));
+}
+
+int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
+{
+ struct fxls8962af_data *data;
+ struct iio_dev *indio_dev;
+ unsigned int reg;
+ int ret, i;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ data = iio_priv(indio_dev);
+ dev_set_drvdata(dev, indio_dev);
+ data->regmap = regmap;
+
+ ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation);
+ if (ret)
+ return ret;
+
+ data->vdd_reg = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(data->vdd_reg))
+ return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
+ "Failed to get vdd regulator\n");
+
+ ret = regulator_enable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, ®);
+ if (ret < 0)
+ return ret;
+
+ for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
+ if (fxls_chip_info_table[i].chip_id == reg) {
+ data->chip_info = &fxls_chip_info_table[i];
+ break;
+ }
+ }
+ if (i == ARRAY_SIZE(fxls_chip_info_table)) {
+ dev_err(dev, "failed to match device in table\n");
+ return -ENXIO;
+ }
+
+ indio_dev->channels = data->chip_info->channels;
+ indio_dev->num_channels = data->chip_info->num_channels;
+ indio_dev->name = data->chip_info->name;
+ indio_dev->info = &fxls8962af_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+
+ ret = fxls8962af_reset(data);
+ if (ret < 0)
+ return ret;
+
+ ret = pm_runtime_set_active(dev);
+ if (ret < 0)
+ return ret;
+
+ pm_runtime_enable(dev);
+ pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(dev);
+
+ ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
+ if (ret)
+ return ret;
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
+
+static int __maybe_unused fxls8962af_runtime_suspend(struct device *dev)
+{
+ struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
+ int ret;
+
+ ret = fxls8962af_standby(data);
+ if (ret < 0) {
+ dev_err(dev, "powering off device failed\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int __maybe_unused fxls8962af_runtime_resume(struct device *dev)
+{
+ struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
+
+ return fxls8962af_active(data);
+}
+
+const struct dev_pm_ops fxls8962af_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
+ fxls8962af_runtime_resume, NULL)
+};
+EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af-i2c.c b/drivers/iio/accel/fxls8962af-i2c.c
new file mode 100644
index 000000000000..0dd86ece46ae
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-i2c.c
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver
+ *
+ * Copyright 2021 Connected Cars A/S
+ */
+
+#include <linux/dev_printk.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "fxls8962af.h"
+
+static int fxls8962af_probe(struct i2c_client *client)
+{
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
+ if (IS_ERR(regmap)) {
+ dev_err(&client->dev, "Failed to initialize i2c regmap\n");
+ return PTR_ERR(regmap);
+ }
+
+ return fxls8962af_core_probe(&client->dev, regmap, client->irq);
+}
+
+static const struct i2c_device_id fxls8962af_id[] = {
+ {"fxls8962af", fxls8962af},
+ {"fxls8964af", fxls8964af},
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, fxls8962af_id);
+
+static const struct of_device_id fxls8962af_of_match[] = {
+ {.compatible = "nxp,fxls8962af"},
+ {.compatible = "nxp,fxls8964af"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, fxls8962af_of_match);
+
+static struct i2c_driver fxls8962af_driver = {
+ .driver = {
+ .name = "fxls8962af_i2c",
+ .of_match_table = fxls8962af_of_match,
+ .pm = &fxls8962af_pm_ops,
+ },
+ .probe_new = fxls8962af_probe,
+ .id_table = fxls8962af_id,
+};
+
+module_i2c_driver(fxls8962af_driver);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer i2c driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af-spi.c b/drivers/iio/accel/fxls8962af-spi.c
new file mode 100644
index 000000000000..0597c3fef504
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af-spi.c
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver
+ *
+ * Copyright 2021 Connected Cars A/S
+ */
+
+#include <linux/dev_printk.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+//#include <linux/slab.h>
+#include <linux/regmap.h>
+
+#include "fxls8962af.h"
+
+static int fxls8962af_probe(struct spi_device *spi)
+{
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
+ if (IS_ERR(regmap)) {
+ dev_err(&spi->dev, "Failed to initialize spi regmap\n");
+ return PTR_ERR(regmap);
+ }
+
+ return fxls8962af_core_probe(&spi->dev, regmap, spi->irq);
+}
+
+static const struct of_device_id fxls8962af_spi_of_match[] = {
+ {.compatible = "nxp,fxls8962af"},
+ {.compatible = "nxp,fxls8964af"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, fxls8962af_spi_of_match);
+
+static const struct spi_device_id fxls8962af_spi_id_table[] = {
+ {"fxls8962af", fxls8962af},
+ {"fxls8964af", fxls8964af},
+ {}
+};
+MODULE_DEVICE_TABLE(spi, fxls8962af_spi_id_table);
+
+static struct spi_driver fxls8962af_driver = {
+ .driver = {
+ .name = "fxls8962af_spi",
+ .pm = &fxls8962af_pm_ops,
+ .of_match_table = fxls8962af_spi_of_match,
+ },
+ .probe = fxls8962af_probe,
+ .id_table = fxls8962af_spi_id_table,
+};
+
+module_spi_driver(fxls8962af_driver);
+
+MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
+MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer spi driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/accel/fxls8962af.h b/drivers/iio/accel/fxls8962af.h
new file mode 100644
index 000000000000..1dc3b0e317dc
--- /dev/null
+++ b/drivers/iio/accel/fxls8962af.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2021 Connected Cars A/S
+ */
+#ifndef _FXLS8962AF_H_
+#define _FXLS8962AF_H_
+
+struct regmap;
+struct device;
+
+enum {
+ fxls8962af,
+ fxls8964af,
+};
+
+int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq);
+int fxls8962af_core_remove(struct device *dev);
+extern const struct dev_pm_ops fxls8962af_pm_ops;
+extern const struct regmap_config fxls8962af_regmap_conf;
+
+#endif /* _FXLS8962AF_H_ */
--
2.31.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings
2021-04-23 10:19 [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Sean Nyekjaer
@ 2021-04-23 10:19 ` Sean Nyekjaer
2021-04-24 10:29 ` Jonathan Cameron
2021-04-23 12:51 ` [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Andy Shevchenko
1 sibling, 1 reply; 7+ messages in thread
From: Sean Nyekjaer @ 2021-04-23 10:19 UTC (permalink / raw)
To: jic23, linux-iio, andy.shevchenko, lars, Nuno.Sa, robh+dt, devicetree
Cc: Sean Nyekjaer
Add devicetree binding for the NXP FXLS8962AF/FXLS8964AF
accelerometer sensor.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
---
Changes for v2:
- removed requirement for interrupt
.../bindings/iio/accel/nxp,fxls8962af.yaml | 72 +++++++++++++++++++
1 file changed, 72 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
new file mode 100644
index 000000000000..d8ac25402979
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/accel/nxp,fxls8962af.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP FXLS8962AF/FXLS8964AF Accelerometer driver
+
+maintainers:
+ - Sean Nyekjaer <sean@geanix.com>
+
+description: |
+ NXP FXLS8962AF/FXLS8964AF Accelerometer driver that supports
+ SPI and I2C interface.
+ https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
+ https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
+
+properties:
+ compatible:
+ enum:
+ - nxp,fxls8962af
+ - nxp,fxls8964af
+
+ reg:
+ maxItems: 1
+
+ vdd-supply:
+ description: phandle to the regulator that provides power to the accelerometer
+
+ spi-max-frequency: true
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Example for a I2C device node */
+ accelerometer@62 {
+ compatible = "nxp,fxls8962af";
+ reg = <0x62>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Example for a SPI device node */
+ accelerometer@0 {
+ compatible = "nxp,fxls8962af";
+ reg = <0>;
+ spi-max-frequency = <4000000>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
--
2.31.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers
2021-04-23 10:19 [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Sean Nyekjaer
2021-04-23 10:19 ` [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings Sean Nyekjaer
@ 2021-04-23 12:51 ` Andy Shevchenko
2021-04-24 10:43 ` Jonathan Cameron
2021-04-27 15:11 ` Sean Nyekjaer
1 sibling, 2 replies; 7+ messages in thread
From: Andy Shevchenko @ 2021-04-23 12:51 UTC (permalink / raw)
To: Sean Nyekjaer
Cc: Jonathan Cameron, linux-iio, Lars-Peter Clausen, Nuno Sá,
Rob Herring, devicetree
On Fri, Apr 23, 2021 at 1:20 PM Sean Nyekjaer <sean@geanix.com> wrote:
Thanks for an update, my comments below.
After addressing them feel free to add
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
> accelerometers.
> It will allow setting up scale/gain and reading x,y,z
> axis.
> Datasheets for the devices can be found here:
> https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
Can you split it into two Datasheet: tags?
> Signed-off-by: Sean Nyekjaer <sean@geanix.com>
> ---
> Changes for v2:
> - Addressed Kconfig comments
> - Using regmap_read_poll_timeout()
> - Addresed comments from Andy and Jonathan
>
> drivers/iio/accel/Kconfig | 27 ++
> drivers/iio/accel/Makefile | 3 +
> drivers/iio/accel/fxls8962af-core.c | 620 ++++++++++++++++++++++++++++
> drivers/iio/accel/fxls8962af-i2c.c | 57 +++
> drivers/iio/accel/fxls8962af-spi.c | 57 +++
> drivers/iio/accel/fxls8962af.h | 21 +
> 6 files changed, 785 insertions(+)
> create mode 100644 drivers/iio/accel/fxls8962af-core.c
> create mode 100644 drivers/iio/accel/fxls8962af-i2c.c
> create mode 100644 drivers/iio/accel/fxls8962af-spi.c
> create mode 100644 drivers/iio/accel/fxls8962af.h
>
> diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
> index 2e0c62c39155..902f2e2edf65 100644
> --- a/drivers/iio/accel/Kconfig
> +++ b/drivers/iio/accel/Kconfig
> @@ -208,6 +208,33 @@ config DMARD10
> Choosing M will build the driver as a module. If so, the module
> will be called dmard10.
>
> +config FXLS8962AF
> + tristate
> +
> +config FXLS8962AF_I2C
> + tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver"
> + depends on I2C
> + select REGMAP_I2C
> + select FXLS8962AF
> + help
> + Say yes here to build support for the NXP 3-axis automotive
> + accelerometer FXLS8962AF/FXLS8964AF with I2C support.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called fxls8962af_i2c.
> +
> +config FXLS8962AF_SPI
> + tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver"
> + depends on SPI
> + select FXLS8962AF
> + select REGMAP_SPI
> + help
> + Say yes here to build support for the NXP 3-axis automotive
> + accelerometer FXLS8962AF/FXLS8964AF with SPI support.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called fxls8962af_spi.
> +
> config HID_SENSOR_ACCEL_3D
> depends on HID_SENSOR_HUB
> select IIO_BUFFER
> diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
> index 4f6c1ebe13b0..1b8c479c6f7c 100644
> --- a/drivers/iio/accel/Makefile
> +++ b/drivers/iio/accel/Makefile
> @@ -25,6 +25,9 @@ obj-$(CONFIG_DA311) += da311.o
> obj-$(CONFIG_DMARD06) += dmard06.o
> obj-$(CONFIG_DMARD09) += dmard09.o
> obj-$(CONFIG_DMARD10) += dmard10.o
> +obj-$(CONFIG_FXLS8962AF) += fxls8962af-core.o
> +obj-$(CONFIG_FXLS8962AF_I2C) += fxls8962af-i2c.o
> +obj-$(CONFIG_FXLS8962AF_SPI) += fxls8962af-spi.o
> obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
> obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
> obj-$(CONFIG_KXSD9) += kxsd9.o
> diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
> new file mode 100644
> index 000000000000..6fda3bc1f28f
> --- /dev/null
> +++ b/drivers/iio/accel/fxls8962af-core.c
> @@ -0,0 +1,620 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * NXP FXLS8962AF/FXLS8964AF Accelerometer Core Driver
> + *
> + * Copyright 2021 Connected Cars A/S
> + *
> + * Datasheet:
> + * https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> + * https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/bitfield.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +
> +#include "fxls8962af.h"
> +
> +#define FXLS8962AF_INT_STATUS 0x00
> +#define FXLS8962AF_INT_STATUS_SRC_DRDY BIT(7)
> +#define FXLS8962AF_TEMP_OUT 0x01
> +#define FXLS8962AF_VECM_LSB 0x02
> +#define FXLS8962AF_OUT_X_LSB 0x04
> +#define FXLS8962AF_OUT_Y_LSB 0x06
> +#define FXLS8962AF_OUT_Z_LSB 0x08
> +#define FXLS8962AF_BUF_STATUS 0x0b
> +#define FXLS8962AF_BUF_X_LSB 0x0c
> +#define FXLS8962AF_BUF_Y_LSB 0x0e
> +#define FXLS8962AF_BUF_Z_LSB 0x10
> +
> +#define FXLS8962AF_PROD_REV 0x12
> +#define FXLS8962AF_WHO_AM_I 0x13
> +
> +#define FXLS8962AF_SYS_MODE 0x14
> +#define FXLS8962AF_SENS_CONFIG1 0x15
> +#define FXLS8962AF_SENS_CONFIG1_ACTIVE BIT(0)
> +#define FXLS8962AF_SENS_CONFIG1_RST BIT(7)
> +#define FXLS8962AF_SC1_FSR_MASK GENMASK(2, 1)
> +#define FXLS8962AF_SC1_FSR_PREP(x) FIELD_PREP(FXLS8962AF_SC1_FSR_MASK, x)
> +#define FXLS8962AF_SC1_FSR_GET(x) FIELD_GET(FXLS8962AF_SC1_FSR_MASK, x)
> +
> +#define FXLS8962AF_SENS_CONFIG2 0x16
> +#define FXLS8962AF_SENS_CONFIG3 0x17
> +#define FXLS8962AF_SENS_CONFIG4 0x18
> +#define FXLS8962AF_SENS_CONFIG5 0x19
> +
> +#define FXLS8962AF_WAKE_IDLE_LSB 0x1b
> +#define FXLS8962AF_SLEEP_IDLE_LSB 0x1c
> +#define FXLS8962AF_ASLP_COUNT_LSB 0x1e
> +
> +#define FXLS8962AF_INT_EN 0x20
> +#define FXLS8962AF_INT_PIN_SEL 0x21
> +
> +#define FXLS8962AF_OFF_X 0x22
> +#define FXLS8962AF_OFF_Y 0x23
> +#define FXLS8962AF_OFF_Z 0x24
> +
> +#define FXLS8962AF_BUF_CONFIG1 0x26
> +#define FXLS8962AF_BUF_CONFIG2 0x27
> +
> +#define FXLS8962AF_ORIENT_STATUS 0x28
> +#define FXLS8962AF_ORIENT_CONFIG 0x29
> +#define FXLS8962AF_ORIENT_DBCOUNT 0x2a
> +#define FXLS8962AF_ORIENT_BF_ZCOMP 0x2b
> +#define FXLS8962AF_ORIENT_THS_REG 0x2c
> +
> +#define FXLS8962AF_SDCD_INT_SRC1 0x2d
> +#define FXLS8962AF_SDCD_INT_SRC2 0x2e
> +#define FXLS8962AF_SDCD_CONFIG1 0x2f
> +#define FXLS8962AF_SDCD_CONFIG2 0x30
> +#define FXLS8962AF_SDCD_OT_DBCNT 0x31
> +#define FXLS8962AF_SDCD_WT_DBCNT 0x32
> +#define FXLS8962AF_SDCD_LTHS_LSB 0x33
> +#define FXLS8962AF_SDCD_UTHS_LSB 0x35
> +
> +#define FXLS8962AF_SELF_TEST_CONFIG1 0x37
> +#define FXLS8962AF_SELF_TEST_CONFIG2 0x38
> +
> +#define FXLS8962AF_MAX_REG 0x38
> +
> +#define FXLS8962AF_DEVICE_ID 0x62
> +#define FXLS8964AF_DEVICE_ID 0x84
> +
> +/*Raw temp channel offset */
Missed space.
> +#define FXLS8962AF_TEMP_CENTER_VAL 25
> +
> +#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS 2000
> +
> +#define FXLS8962AF_SCALE_TABLE_LEN 4
> +
> +static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
> + {0, IIO_G_TO_M_S_2(980000)},
> + {0, IIO_G_TO_M_S_2(1950000)},
> + {0, IIO_G_TO_M_S_2(3910000)},
> + {0, IIO_G_TO_M_S_2(7810000)},
> +};
> +
> +struct fxls8962af_chip_info {
> + const char *name;
> + const struct iio_chan_spec *channels;
> + int num_channels;
> + u8 chip_id;
> +};
> +
> +struct fxls8962af_data {
> + struct regmap *regmap;
> + const struct fxls8962af_chip_info *chip_info;
> + struct regulator *vdd_reg;
> + struct iio_mount_matrix orientation;
> +};
> +
> +const struct regmap_config fxls8962af_regmap_conf = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = FXLS8962AF_MAX_REG,
> +};
> +EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
> +
> +enum {
> + fxls8962af_idx_x,
> + fxls8962af_idx_y,
> + fxls8962af_idx_z,
> + fxls8962af_idx_ts,
> +};
> +
> +static int fxls8962af_drdy(struct fxls8962af_data *data)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_INT_STATUS, reg,
> + (reg & FXLS8962AF_INT_STATUS_SRC_DRDY), 20000, 2000000);
> + if (ret) {
> + dev_err(dev, "drdy timeout, int_status = 0x%x\n", reg);
> + return ret;
> + }
> +
> + return 0;
It can be (all 4 LOCs) simply
return ret;
> +}
> +
> +static int fxls8962af_power_on(struct fxls8962af_data *data)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + int ret;
> +
> + ret = pm_runtime_get_sync(dev);
> +
> + if (ret < 0) {
> + dev_err(dev, "failed to power on\n");
> + pm_runtime_put_noidle(dev);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int fxls8962af_power_off(struct fxls8962af_data *data)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + int ret;
> +
> + pm_runtime_mark_last_busy(dev);
> + ret = pm_runtime_put_autosuspend(dev);
> +
> + if (ret < 0) {
> + dev_err(dev, "failed to power off\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int fxls8962af_get_temp(struct fxls8962af_data *data, int *val)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + int ret;
> + unsigned int value;
Can we keep reversed xmas tree order?
> + ret = fxls8962af_drdy(data);
> + if (ret < 0)
> + return ret;
> +
> + ret = fxls8962af_power_on(data);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(data->regmap, FXLS8962AF_TEMP_OUT, &value);
> + if (ret < 0) {
> + dev_err(dev, "Error reading reg_temp\n");
> + fxls8962af_power_off(data);
> + return ret;
> + }
> +
> + fxls8962af_power_off(data);
> +
> + *val = sign_extend32(value, 7);
> +
> + return IIO_VAL_INT;
> +}
> +
> +static int fxls8962af_get_axis(struct fxls8962af_data *data,
> + struct iio_chan_spec const *chan, int *val)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + int ret;
> + __le16 raw_val;
Ditto.
> + ret = fxls8962af_drdy(data);
> + if (ret < 0)
> + return ret;
> +
> + ret = fxls8962af_power_on(data);
> + if (ret)
> + return ret;
> +
> + ret = regmap_bulk_read(data->regmap, chan->address,
> + &raw_val, sizeof(raw_val));
> + if (ret < 0) {
> + dev_err(dev, "failed to read axes\n");
> + fxls8962af_power_off(data);
> + return ret;
> + }
> +
> + fxls8962af_power_off(data);
> +
> + *val = sign_extend32(le16_to_cpu(raw_val), chan->scan_type.realbits - 1);
> +
> + return IIO_VAL_INT;
> +}
> +
> +static int fxls8962af_read_avail(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + const int **vals, int *type, int *length,
> + long mask)
> +{
> + switch (mask) {
> + case IIO_CHAN_INFO_SCALE:
> + *type = IIO_VAL_INT_PLUS_NANO;
> + *vals = (int *)fxls8962af_scale_table;
> + *length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
> + return IIO_AVAIL_LIST;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + long mask)
> +{
> + return IIO_VAL_INT_PLUS_NANO;
> +}
> +
> +static int fxls8962af_standby(struct fxls8962af_data *data)
> +{
> + return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> + FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
> +}
> +
> +static int fxls8962af_active(struct fxls8962af_data *data)
> +{
> + return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> + FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
> +}
> +
> +static int fxls8962af_is_active(struct fxls8962af_data *data)
> +{
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
> + if (ret < 0)
> + return ret;
> +
> + return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
> +}
> +
> +static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
> + u8 mask, u8 val)
> +{
> + int ret;
> + int is_active;
> +
> + is_active = fxls8962af_is_active(data);
> + if (is_active) {
> + ret = fxls8962af_standby(data);
> + if (ret < 0)
> + return ret;
> + }
> +
> + ret = regmap_update_bits(data->regmap, reg, mask, val);
> + if (ret < 0)
> + return ret;
> +
> + if (is_active) {
> + ret = fxls8962af_active(data);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
> +{
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
> + if (scale == fxls8962af_scale_table[i][1])
> + break;
> +
> + if (i == ARRAY_SIZE(fxls8962af_scale_table))
> + return -EINVAL;
> +
> + return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
> + FXLS8962AF_SC1_FSR_MASK,
> + FXLS8962AF_SC1_FSR_PREP(i));
> +}
> +
> +static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
> + int *val)
> +{
> + int ret;
> + unsigned int reg;
> + u8 range_idx;
> +
> + ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
> + if (ret < 0)
> + return ret;
> +
> + range_idx = FXLS8962AF_SC1_FSR_GET(reg);
> +
> + *val = fxls8962af_scale_table[range_idx][1];
> +
> + return IIO_VAL_INT_PLUS_NANO;
> +}
> +
> +static int fxls8962af_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct fxls8962af_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + ret = iio_device_claim_direct_mode(indio_dev);
> + if (ret)
> + return ret;
> +
> + switch (chan->type) {
> + case IIO_TEMP:
> + ret = fxls8962af_get_temp(data, val);
> + break;
> + case IIO_ACCEL:
> + ret = fxls8962af_get_axis(data, chan, val);
> + break;
> + default:
> + ret = -EINVAL;
> + break;
return -EINVAL;
> + }
> +
> + iio_device_release_direct_mode(indio_dev);
> + return ret;
> + case IIO_CHAN_INFO_OFFSET:
> + if (chan->type == IIO_TEMP) {
Can we use traditional pattern here, i.e.
if (type != IIO_TEMP)
return -EINVAL;
?
> + *val = FXLS8962AF_TEMP_CENTER_VAL;
> + return IIO_VAL_INT;
> + }
> + break;
> + case IIO_CHAN_INFO_SCALE:
> + *val = 0;
> + return fxls8962af_read_full_scale(data, val2);
> + default:
> + return -EINVAL;
> + }
> +
> + return -EINVAL;
(Almost) dead code (see above).
> +}
> +
> +static int fxls8962af_write_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int val, int val2, long mask)
> +{
> + struct fxls8962af_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_SCALE:
> + if (val != 0)
> + return -EINVAL;
> +
> + ret = iio_device_claim_direct_mode(indio_dev);
> + if (ret)
> + return ret;
> +
> + ret = fxls8962af_set_full_scale(data, val2);
> +
> + iio_device_release_direct_mode(indio_dev);
> + return ret;
> + default:
> + return -EINVAL;
> + }
> +
> + return -EINVAL;
Dead code.
> +}
> +
> +#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
> + .type = IIO_ACCEL, \
> + .address = reg, \
> + .modified = 1, \
> + .channel2 = IIO_MOD_##axis, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> + .info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
> + .scan_index = idx, \
> + .scan_type = { \
> + .sign = 's', \
> + .realbits = 12, \
> + .storagebits = 16, \
> + .shift = 4, \
> + .endianness = IIO_BE, \
> + }, \
> +}
> +
> +#define FXLS8962AF_TEMP_CHANNEL { \
> + .type = IIO_TEMP, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
> + BIT(IIO_CHAN_INFO_OFFSET),\
> + .scan_index = -1, \
> + .scan_type = { \
> + .realbits = 8, \
> + }, \
> +}
> +
> +static const struct iio_chan_spec fxls8962af_channels[] = {
> + FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
> + FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
> + FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
> + IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
> + FXLS8962AF_TEMP_CHANNEL,
> +};
> +
> +static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
> + [fxls8962af] = {
> + .chip_id = FXLS8962AF_DEVICE_ID,
> + .name = "fxls8962af",
> + .channels = fxls8962af_channels,
> + .num_channels = ARRAY_SIZE(fxls8962af_channels),
> + },
> + [fxls8964af] = {
> + .chip_id = FXLS8964AF_DEVICE_ID,
> + .name = "fxls8964af",
> + .channels = fxls8962af_channels,
> + .num_channels = ARRAY_SIZE(fxls8962af_channels),
> + },
> +};
> +
> +static const struct iio_info fxls8962af_info = {
> + .read_raw = &fxls8962af_read_raw,
> + .write_raw = &fxls8962af_write_raw,
> + .write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
> + .read_avail = fxls8962af_read_avail,
> +};
> +
> +static int fxls8962af_reset(struct fxls8962af_data *data)
> +{
> + struct device *dev = regmap_get_device(data->regmap);
> + unsigned int reg;
> + int ret;
> +
> + ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> + FXLS8962AF_SENS_CONFIG1_RST,
> + FXLS8962AF_SENS_CONFIG1_RST);
> + if (ret < 0)
> + return ret;
> +
> + /* TBOOT1, TBOOT2, specifies we have to wait between 1 - 17.7ms */
> + ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_SENS_CONFIG1, reg,
> + !(reg & FXLS8962AF_SENS_CONFIG1_RST), 1000, 18000);
> + if (ret) {
> + dev_err(dev, "reset timeout, sens_config1 = 0x%x\n", reg);
> + return ret;
> + }
These two lines are redundant.
> +
> + return ret;
> +}
> +
> +static void fxls8962af_regulator_disable(void *data_ptr)
> +{
> + struct fxls8962af_data *data = data_ptr;
> +
> + regulator_disable(data->vdd_reg);
> +}
> +
> +static void fxls8962af_pm_disable(void *dev_ptr)
> +{
> + struct device *dev = dev_ptr;
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> +
> + pm_runtime_disable(dev);
> + pm_runtime_set_suspended(dev);
> + pm_runtime_put_noidle(dev);
> +
> + fxls8962af_standby(iio_priv(indio_dev));
> +}
> +
> +int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
> +{
> + struct fxls8962af_data *data;
> + struct iio_dev *indio_dev;
> + unsigned int reg;
> + int ret, i;
> +
> + indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + data = iio_priv(indio_dev);
> + dev_set_drvdata(dev, indio_dev);
> + data->regmap = regmap;
> +
> + ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation);
> + if (ret)
> + return ret;
> +
> + data->vdd_reg = devm_regulator_get(dev, "vdd");
> + if (IS_ERR(data->vdd_reg))
> + return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
> + "Failed to get vdd regulator\n");
> +
> + ret = regulator_enable(data->vdd_reg);
> + if (ret) {
> + dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
> + return ret;
> + }
> +
> + ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, ®);
> + if (ret < 0)
> + return ret;
> +
> + for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
> + if (fxls_chip_info_table[i].chip_id == reg) {
> + data->chip_info = &fxls_chip_info_table[i];
> + break;
> + }
> + }
> + if (i == ARRAY_SIZE(fxls_chip_info_table)) {
> + dev_err(dev, "failed to match device in table\n");
> + return -ENXIO;
> + }
> +
> + indio_dev->channels = data->chip_info->channels;
> + indio_dev->num_channels = data->chip_info->num_channels;
> + indio_dev->name = data->chip_info->name;
> + indio_dev->info = &fxls8962af_info;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + ret = fxls8962af_reset(data);
> + if (ret < 0)
> + return ret;
> +
> + ret = pm_runtime_set_active(dev);
> + if (ret < 0)
> + return ret;
> +
> + pm_runtime_enable(dev);
> + pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
> + pm_runtime_use_autosuspend(dev);
> +
> + ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
> + if (ret)
> + return ret;
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
> +EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
> +
> +static int __maybe_unused fxls8962af_runtime_suspend(struct device *dev)
> +{
> + struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
> + int ret;
> +
> + ret = fxls8962af_standby(data);
> + if (ret < 0) {
> + dev_err(dev, "powering off device failed\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int __maybe_unused fxls8962af_runtime_resume(struct device *dev)
> +{
> + struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
> +
> + return fxls8962af_active(data);
> +}
> +
> +const struct dev_pm_ops fxls8962af_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> + pm_runtime_force_resume)
> + SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
> + fxls8962af_runtime_resume, NULL)
> +};
> +EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
> +
> +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/iio/accel/fxls8962af-i2c.c b/drivers/iio/accel/fxls8962af-i2c.c
> new file mode 100644
> index 000000000000..0dd86ece46ae
> --- /dev/null
> +++ b/drivers/iio/accel/fxls8962af-i2c.c
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver
> + *
> + * Copyright 2021 Connected Cars A/S
> + */
> +
> +#include <linux/dev_printk.h>
+ err.h
> +#include <linux/i2c.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +
> +#include "fxls8962af.h"
> +
> +static int fxls8962af_probe(struct i2c_client *client)
> +{
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "Failed to initialize i2c regmap\n");
> + return PTR_ERR(regmap);
> + }
> +
> + return fxls8962af_core_probe(&client->dev, regmap, client->irq);
> +}
> +
> +static const struct i2c_device_id fxls8962af_id[] = {
> + {"fxls8962af", fxls8962af},
> + {"fxls8964af", fxls8964af},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, fxls8962af_id);
> +
> +static const struct of_device_id fxls8962af_of_match[] = {
> + {.compatible = "nxp,fxls8962af"},
> + {.compatible = "nxp,fxls8964af"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, fxls8962af_of_match);
> +
> +static struct i2c_driver fxls8962af_driver = {
> + .driver = {
> + .name = "fxls8962af_i2c",
> + .of_match_table = fxls8962af_of_match,
> + .pm = &fxls8962af_pm_ops,
> + },
> + .probe_new = fxls8962af_probe,
> + .id_table = fxls8962af_id,
> +};
> +
No need a blank line here.
> +module_i2c_driver(fxls8962af_driver);
> +
> +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer i2c driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/iio/accel/fxls8962af-spi.c b/drivers/iio/accel/fxls8962af-spi.c
> new file mode 100644
> index 000000000000..0597c3fef504
> --- /dev/null
> +++ b/drivers/iio/accel/fxls8962af-spi.c
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver
> + *
> + * Copyright 2021 Connected Cars A/S
> + */
> +
> +#include <linux/dev_printk.h>
+ err.h
+ mod_devicetable.h
> +#include <linux/module.h>
> +#include <linux/spi/spi.h>
> +//#include <linux/slab.h>
???
Remove it.
> +#include <linux/regmap.h>
> +
> +#include "fxls8962af.h"
> +
> +static int fxls8962af_probe(struct spi_device *spi)
> +{
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
> + if (IS_ERR(regmap)) {
> + dev_err(&spi->dev, "Failed to initialize spi regmap\n");
> + return PTR_ERR(regmap);
> + }
> +
> + return fxls8962af_core_probe(&spi->dev, regmap, spi->irq);
> +}
> +
> +static const struct of_device_id fxls8962af_spi_of_match[] = {
> + {.compatible = "nxp,fxls8962af"},
> + {.compatible = "nxp,fxls8964af"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, fxls8962af_spi_of_match);
> +
> +static const struct spi_device_id fxls8962af_spi_id_table[] = {
> + {"fxls8962af", fxls8962af},
> + {"fxls8964af", fxls8964af},
> + {}
> +};
> +MODULE_DEVICE_TABLE(spi, fxls8962af_spi_id_table);
> +
> +static struct spi_driver fxls8962af_driver = {
> + .driver = {
> + .name = "fxls8962af_spi",
> + .pm = &fxls8962af_pm_ops,
> + .of_match_table = fxls8962af_spi_of_match,
> + },
> + .probe = fxls8962af_probe,
> + .id_table = fxls8962af_spi_id_table,
> +};
> +
No need to have a blank line here.
> +module_spi_driver(fxls8962af_driver);
> +
> +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer spi driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/iio/accel/fxls8962af.h b/drivers/iio/accel/fxls8962af.h
> new file mode 100644
> index 000000000000..1dc3b0e317dc
> --- /dev/null
> +++ b/drivers/iio/accel/fxls8962af.h
> @@ -0,0 +1,21 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright 2021 Connected Cars A/S
> + */
> +#ifndef _FXLS8962AF_H_
> +#define _FXLS8962AF_H_
> +
> +struct regmap;
> +struct device;
> +
> +enum {
> + fxls8962af,
> + fxls8964af,
> +};
> +
> +int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq);
> +int fxls8962af_core_remove(struct device *dev);
+ blank line?
> +extern const struct dev_pm_ops fxls8962af_pm_ops;
> +extern const struct regmap_config fxls8962af_regmap_conf;
> +
> +#endif /* _FXLS8962AF_H_ */
> --
> 2.31.0
>
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings
2021-04-23 10:19 ` [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings Sean Nyekjaer
@ 2021-04-24 10:29 ` Jonathan Cameron
0 siblings, 0 replies; 7+ messages in thread
From: Jonathan Cameron @ 2021-04-24 10:29 UTC (permalink / raw)
To: Sean Nyekjaer
Cc: linux-iio, andy.shevchenko, lars, Nuno.Sa, robh+dt, devicetree
On Fri, 23 Apr 2021 12:19:51 +0200
Sean Nyekjaer <sean@geanix.com> wrote:
> Add devicetree binding for the NXP FXLS8962AF/FXLS8964AF
> accelerometer sensor.
>
> Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Trivial comment inline, but otherwise looks good to me.
Thanks,
Jonathan
> ---
> Changes for v2:
> - removed requirement for interrupt
>
> .../bindings/iio/accel/nxp,fxls8962af.yaml | 72 +++++++++++++++++++
> 1 file changed, 72 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
> new file mode 100644
> index 000000000000..d8ac25402979
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml
> @@ -0,0 +1,72 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/accel/nxp,fxls8962af.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP FXLS8962AF/FXLS8964AF Accelerometer driver
> +
> +maintainers:
> + - Sean Nyekjaer <sean@geanix.com>
> +
> +description: |
> + NXP FXLS8962AF/FXLS8964AF Accelerometer driver that supports
> + SPI and I2C interface.
> + https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> + https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
> +
> +properties:
> + compatible:
> + enum:
> + - nxp,fxls8962af
> + - nxp,fxls8964af
> +
> + reg:
> + maxItems: 1
> +
> + vdd-supply:
> + description: phandle to the regulator that provides power to the accelerometer
> +
> + spi-max-frequency: true
> +
> + interrupts:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> + i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Example for a I2C device node */
> + accelerometer@62 {
> + compatible = "nxp,fxls8962af";
> + reg = <0x62>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> + - |
> + #include <dt-bindings/gpio/gpio.h>
Fair sure we don't need the gpio.h header here though it does
no real harm.
> + #include <dt-bindings/interrupt-controller/irq.h>
> + spi0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Example for a SPI device node */
> + accelerometer@0 {
> + compatible = "nxp,fxls8962af";
> + reg = <0>;
> + spi-max-frequency = <4000000>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers
2021-04-23 12:51 ` [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Andy Shevchenko
@ 2021-04-24 10:43 ` Jonathan Cameron
2021-04-27 15:11 ` Sean Nyekjaer
1 sibling, 0 replies; 7+ messages in thread
From: Jonathan Cameron @ 2021-04-24 10:43 UTC (permalink / raw)
To: Andy Shevchenko
Cc: Sean Nyekjaer, linux-iio, Lars-Peter Clausen, Nuno Sá,
Rob Herring, devicetree
On Fri, 23 Apr 2021 15:51:43 +0300
Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> On Fri, Apr 23, 2021 at 1:20 PM Sean Nyekjaer <sean@geanix.com> wrote:
>
> Thanks for an update, my comments below.
> After addressing them feel free to add
>
> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
>
Reviewed on top of Andy to avoid any potential repetition.
Just one addition inline from me. Right now you have an interrupt
parameter passed to the core code that isn't used. If you plan
to add support for that in a follow up patch, then please add
a comment in this patch intro to say so. If not, then just drop
that parameter and it can come back as part of the patch adding that
support.
Thanks,
Jonathan
> > Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
> > accelerometers.
> > It will allow setting up scale/gain and reading x,y,z
> > axis.
>
> > Datasheets for the devices can be found here:
> > https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> > https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
>
>
> Can you split it into two Datasheet: tags?
>
> > Signed-off-by: Sean Nyekjaer <sean@geanix.com>
> > ---
> > Changes for v2:
> > - Addressed Kconfig comments
> > - Using regmap_read_poll_timeout()
> > - Addresed comments from Andy and Jonathan
> >
> > drivers/iio/accel/Kconfig | 27 ++
> > drivers/iio/accel/Makefile | 3 +
> > drivers/iio/accel/fxls8962af-core.c | 620 ++++++++++++++++++++++++++++
> > drivers/iio/accel/fxls8962af-i2c.c | 57 +++
> > drivers/iio/accel/fxls8962af-spi.c | 57 +++
> > drivers/iio/accel/fxls8962af.h | 21 +
> > 6 files changed, 785 insertions(+)
> > create mode 100644 drivers/iio/accel/fxls8962af-core.c
> > create mode 100644 drivers/iio/accel/fxls8962af-i2c.c
> > create mode 100644 drivers/iio/accel/fxls8962af-spi.c
> > create mode 100644 drivers/iio/accel/fxls8962af.h
> >
> > diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
> > index 2e0c62c39155..902f2e2edf65 100644
> > --- a/drivers/iio/accel/Kconfig
> > +++ b/drivers/iio/accel/Kconfig
> > @@ -208,6 +208,33 @@ config DMARD10
> > Choosing M will build the driver as a module. If so, the module
> > will be called dmard10.
> >
> > +config FXLS8962AF
> > + tristate
> > +
> > +config FXLS8962AF_I2C
> > + tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver"
> > + depends on I2C
> > + select REGMAP_I2C
> > + select FXLS8962AF
> > + help
> > + Say yes here to build support for the NXP 3-axis automotive
> > + accelerometer FXLS8962AF/FXLS8964AF with I2C support.
> > +
> > + To compile this driver as a module, choose M here: the module
> > + will be called fxls8962af_i2c.
> > +
> > +config FXLS8962AF_SPI
> > + tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver"
> > + depends on SPI
> > + select FXLS8962AF
> > + select REGMAP_SPI
Totally trivial but nice to have same ordering of selects in the two cases :)
> > + help
> > + Say yes here to build support for the NXP 3-axis automotive
> > + accelerometer FXLS8962AF/FXLS8964AF with SPI support.
> > +
> > + To compile this driver as a module, choose M here: the module
> > + will be called fxls8962af_spi.
> > +
> > config HID_SENSOR_ACCEL_3D
> > depends on HID_SENSOR_HUB
> > select IIO_BUFFER
> > diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
> > index 4f6c1ebe13b0..1b8c479c6f7c 100644
> > --- a/drivers/iio/accel/Makefile
> > +++ b/drivers/iio/accel/Makefile
> > @@ -25,6 +25,9 @@ obj-$(CONFIG_DA311) += da311.o
> > obj-$(CONFIG_DMARD06) += dmard06.o
> > obj-$(CONFIG_DMARD09) += dmard09.o
> > obj-$(CONFIG_DMARD10) += dmard10.o
> > +obj-$(CONFIG_FXLS8962AF) += fxls8962af-core.o
> > +obj-$(CONFIG_FXLS8962AF_I2C) += fxls8962af-i2c.o
> > +obj-$(CONFIG_FXLS8962AF_SPI) += fxls8962af-spi.o
> > obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
> > obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
> > obj-$(CONFIG_KXSD9) += kxsd9.o
> > diff --git a/drivers/iio/accel/fxls8962af-core.c b/drivers/iio/accel/fxls8962af-core.c
> > new file mode 100644
> > index 000000000000..6fda3bc1f28f
> > --- /dev/null
> > +++ b/drivers/iio/accel/fxls8962af-core.c
> > @@ -0,0 +1,620 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * NXP FXLS8962AF/FXLS8964AF Accelerometer Core Driver
> > + *
> > + * Copyright 2021 Connected Cars A/S
> > + *
> > + * Datasheet:
> > + * https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
> > + * https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
> > + */
> > +
> > +#include <linux/bits.h>
> > +#include <linux/bitfield.h>
> > +#include <linux/module.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/regmap.h>
> > +
> > +#include <linux/iio/iio.h>
> > +#include <linux/iio/sysfs.h>
> > +
> > +#include "fxls8962af.h"
> > +
> > +#define FXLS8962AF_INT_STATUS 0x00
> > +#define FXLS8962AF_INT_STATUS_SRC_DRDY BIT(7)
> > +#define FXLS8962AF_TEMP_OUT 0x01
> > +#define FXLS8962AF_VECM_LSB 0x02
> > +#define FXLS8962AF_OUT_X_LSB 0x04
> > +#define FXLS8962AF_OUT_Y_LSB 0x06
> > +#define FXLS8962AF_OUT_Z_LSB 0x08
> > +#define FXLS8962AF_BUF_STATUS 0x0b
> > +#define FXLS8962AF_BUF_X_LSB 0x0c
> > +#define FXLS8962AF_BUF_Y_LSB 0x0e
> > +#define FXLS8962AF_BUF_Z_LSB 0x10
> > +
> > +#define FXLS8962AF_PROD_REV 0x12
> > +#define FXLS8962AF_WHO_AM_I 0x13
> > +
> > +#define FXLS8962AF_SYS_MODE 0x14
> > +#define FXLS8962AF_SENS_CONFIG1 0x15
> > +#define FXLS8962AF_SENS_CONFIG1_ACTIVE BIT(0)
> > +#define FXLS8962AF_SENS_CONFIG1_RST BIT(7)
> > +#define FXLS8962AF_SC1_FSR_MASK GENMASK(2, 1)
> > +#define FXLS8962AF_SC1_FSR_PREP(x) FIELD_PREP(FXLS8962AF_SC1_FSR_MASK, x)
> > +#define FXLS8962AF_SC1_FSR_GET(x) FIELD_GET(FXLS8962AF_SC1_FSR_MASK, x)
> > +
> > +#define FXLS8962AF_SENS_CONFIG2 0x16
> > +#define FXLS8962AF_SENS_CONFIG3 0x17
> > +#define FXLS8962AF_SENS_CONFIG4 0x18
> > +#define FXLS8962AF_SENS_CONFIG5 0x19
> > +
> > +#define FXLS8962AF_WAKE_IDLE_LSB 0x1b
> > +#define FXLS8962AF_SLEEP_IDLE_LSB 0x1c
> > +#define FXLS8962AF_ASLP_COUNT_LSB 0x1e
> > +
> > +#define FXLS8962AF_INT_EN 0x20
> > +#define FXLS8962AF_INT_PIN_SEL 0x21
> > +
> > +#define FXLS8962AF_OFF_X 0x22
> > +#define FXLS8962AF_OFF_Y 0x23
> > +#define FXLS8962AF_OFF_Z 0x24
> > +
> > +#define FXLS8962AF_BUF_CONFIG1 0x26
> > +#define FXLS8962AF_BUF_CONFIG2 0x27
> > +
> > +#define FXLS8962AF_ORIENT_STATUS 0x28
> > +#define FXLS8962AF_ORIENT_CONFIG 0x29
> > +#define FXLS8962AF_ORIENT_DBCOUNT 0x2a
> > +#define FXLS8962AF_ORIENT_BF_ZCOMP 0x2b
> > +#define FXLS8962AF_ORIENT_THS_REG 0x2c
> > +
> > +#define FXLS8962AF_SDCD_INT_SRC1 0x2d
> > +#define FXLS8962AF_SDCD_INT_SRC2 0x2e
> > +#define FXLS8962AF_SDCD_CONFIG1 0x2f
> > +#define FXLS8962AF_SDCD_CONFIG2 0x30
> > +#define FXLS8962AF_SDCD_OT_DBCNT 0x31
> > +#define FXLS8962AF_SDCD_WT_DBCNT 0x32
> > +#define FXLS8962AF_SDCD_LTHS_LSB 0x33
> > +#define FXLS8962AF_SDCD_UTHS_LSB 0x35
> > +
> > +#define FXLS8962AF_SELF_TEST_CONFIG1 0x37
> > +#define FXLS8962AF_SELF_TEST_CONFIG2 0x38
> > +
> > +#define FXLS8962AF_MAX_REG 0x38
> > +
> > +#define FXLS8962AF_DEVICE_ID 0x62
> > +#define FXLS8964AF_DEVICE_ID 0x84
> > +
> > +/*Raw temp channel offset */
>
> Missed space.
>
> > +#define FXLS8962AF_TEMP_CENTER_VAL 25
> > +
> > +#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS 2000
> > +
> > +#define FXLS8962AF_SCALE_TABLE_LEN 4
> > +
> > +static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
> > + {0, IIO_G_TO_M_S_2(980000)},
> > + {0, IIO_G_TO_M_S_2(1950000)},
> > + {0, IIO_G_TO_M_S_2(3910000)},
> > + {0, IIO_G_TO_M_S_2(7810000)},
> > +};
> > +
> > +struct fxls8962af_chip_info {
> > + const char *name;
> > + const struct iio_chan_spec *channels;
> > + int num_channels;
> > + u8 chip_id;
> > +};
> > +
> > +struct fxls8962af_data {
> > + struct regmap *regmap;
> > + const struct fxls8962af_chip_info *chip_info;
> > + struct regulator *vdd_reg;
> > + struct iio_mount_matrix orientation;
> > +};
> > +
> > +const struct regmap_config fxls8962af_regmap_conf = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = FXLS8962AF_MAX_REG,
> > +};
> > +EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
> > +
> > +enum {
> > + fxls8962af_idx_x,
> > + fxls8962af_idx_y,
> > + fxls8962af_idx_z,
> > + fxls8962af_idx_ts,
> > +};
> > +
> > +static int fxls8962af_drdy(struct fxls8962af_data *data)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_INT_STATUS, reg,
> > + (reg & FXLS8962AF_INT_STATUS_SRC_DRDY), 20000, 2000000);
> > + if (ret) {
> > + dev_err(dev, "drdy timeout, int_status = 0x%x\n", reg);
>
> > + return ret;
> > + }
> > +
> > + return 0;
>
> It can be (all 4 LOCs) simply
>
> return ret;
>
> > +}
> > +
> > +static int fxls8962af_power_on(struct fxls8962af_data *data)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + int ret;
> > +
> > + ret = pm_runtime_get_sync(dev);
> > +
> > + if (ret < 0) {
> > + dev_err(dev, "failed to power on\n");
> > + pm_runtime_put_noidle(dev);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int fxls8962af_power_off(struct fxls8962af_data *data)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + int ret;
> > +
> > + pm_runtime_mark_last_busy(dev);
> > + ret = pm_runtime_put_autosuspend(dev);
> > +
> > + if (ret < 0) {
> > + dev_err(dev, "failed to power off\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int fxls8962af_get_temp(struct fxls8962af_data *data, int *val)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + int ret;
> > + unsigned int value;
>
> Can we keep reversed xmas tree order?
>
> > + ret = fxls8962af_drdy(data);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = fxls8962af_power_on(data);
> > + if (ret)
> > + return ret;
> > +
> > + ret = regmap_read(data->regmap, FXLS8962AF_TEMP_OUT, &value);
> > + if (ret < 0) {
> > + dev_err(dev, "Error reading reg_temp\n");
> > + fxls8962af_power_off(data);
> > + return ret;
> > + }
> > +
> > + fxls8962af_power_off(data);
> > +
> > + *val = sign_extend32(value, 7);
> > +
> > + return IIO_VAL_INT;
> > +}
> > +
> > +static int fxls8962af_get_axis(struct fxls8962af_data *data,
> > + struct iio_chan_spec const *chan, int *val)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + int ret;
> > + __le16 raw_val;
>
> Ditto.
>
> > + ret = fxls8962af_drdy(data);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = fxls8962af_power_on(data);
> > + if (ret)
> > + return ret;
> > +
> > + ret = regmap_bulk_read(data->regmap, chan->address,
> > + &raw_val, sizeof(raw_val));
> > + if (ret < 0) {
> > + dev_err(dev, "failed to read axes\n");
> > + fxls8962af_power_off(data);
> > + return ret;
> > + }
> > +
> > + fxls8962af_power_off(data);
> > +
> > + *val = sign_extend32(le16_to_cpu(raw_val), chan->scan_type.realbits - 1);
> > +
> > + return IIO_VAL_INT;
> > +}
> > +
> > +static int fxls8962af_read_avail(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + const int **vals, int *type, int *length,
> > + long mask)
> > +{
> > + switch (mask) {
> > + case IIO_CHAN_INFO_SCALE:
> > + *type = IIO_VAL_INT_PLUS_NANO;
> > + *vals = (int *)fxls8962af_scale_table;
> > + *length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
> > + return IIO_AVAIL_LIST;
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + long mask)
> > +{
> > + return IIO_VAL_INT_PLUS_NANO;
> > +}
> > +
> > +static int fxls8962af_standby(struct fxls8962af_data *data)
> > +{
> > + return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> > + FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
> > +}
> > +
> > +static int fxls8962af_active(struct fxls8962af_data *data)
> > +{
> > + return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> > + FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
> > +}
> > +
> > +static int fxls8962af_is_active(struct fxls8962af_data *data)
> > +{
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
> > +}
> > +
> > +static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
> > + u8 mask, u8 val)
> > +{
> > + int ret;
> > + int is_active;
> > +
> > + is_active = fxls8962af_is_active(data);
> > + if (is_active) {
> > + ret = fxls8962af_standby(data);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + ret = regmap_update_bits(data->regmap, reg, mask, val);
> > + if (ret < 0)
> > + return ret;
> > +
> > + if (is_active) {
> > + ret = fxls8962af_active(data);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
> > + if (scale == fxls8962af_scale_table[i][1])
> > + break;
> > +
> > + if (i == ARRAY_SIZE(fxls8962af_scale_table))
> > + return -EINVAL;
> > +
> > + return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
> > + FXLS8962AF_SC1_FSR_MASK,
> > + FXLS8962AF_SC1_FSR_PREP(i));
> > +}
> > +
> > +static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
> > + int *val)
> > +{
> > + int ret;
> > + unsigned int reg;
> > + u8 range_idx;
> > +
> > + ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, ®);
> > + if (ret < 0)
> > + return ret;
> > +
> > + range_idx = FXLS8962AF_SC1_FSR_GET(reg);
> > +
> > + *val = fxls8962af_scale_table[range_idx][1];
> > +
> > + return IIO_VAL_INT_PLUS_NANO;
> > +}
> > +
> > +static int fxls8962af_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int *val, int *val2, long mask)
> > +{
> > + struct fxls8962af_data *data = iio_priv(indio_dev);
> > + int ret;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + ret = iio_device_claim_direct_mode(indio_dev);
> > + if (ret)
> > + return ret;
> > +
> > + switch (chan->type) {
> > + case IIO_TEMP:
> > + ret = fxls8962af_get_temp(data, val);
> > + break;
> > + case IIO_ACCEL:
> > + ret = fxls8962af_get_axis(data, chan, val);
> > + break;
> > + default:
>
> > + ret = -EINVAL;
> > + break;
>
> return -EINVAL;
>
> > + }
> > +
> > + iio_device_release_direct_mode(indio_dev);
> > + return ret;
> > + case IIO_CHAN_INFO_OFFSET:
>
> > + if (chan->type == IIO_TEMP) {
>
> Can we use traditional pattern here, i.e.
>
> if (type != IIO_TEMP)
> return -EINVAL;
>
> ?
>
> > + *val = FXLS8962AF_TEMP_CENTER_VAL;
> > + return IIO_VAL_INT;
> > + }
>
> > + break;
> > + case IIO_CHAN_INFO_SCALE:
> > + *val = 0;
> > + return fxls8962af_read_full_scale(data, val2);
> > + default:
> > + return -EINVAL;
> > + }
>
> > +
> > + return -EINVAL;
>
> (Almost) dead code (see above).
>
> > +}
> > +
> > +static int fxls8962af_write_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int val, int val2, long mask)
> > +{
> > + struct fxls8962af_data *data = iio_priv(indio_dev);
> > + int ret;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_SCALE:
> > + if (val != 0)
> > + return -EINVAL;
> > +
> > + ret = iio_device_claim_direct_mode(indio_dev);
> > + if (ret)
> > + return ret;
> > +
> > + ret = fxls8962af_set_full_scale(data, val2);
> > +
> > + iio_device_release_direct_mode(indio_dev);
> > + return ret;
> > + default:
> > + return -EINVAL;
> > + }
>
> > +
> > + return -EINVAL;
>
> Dead code.
>
> > +}
> > +
> > +#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
> > + .type = IIO_ACCEL, \
> > + .address = reg, \
> > + .modified = 1, \
> > + .channel2 = IIO_MOD_##axis, \
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> > + .info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE), \
> > + .scan_index = idx, \
> > + .scan_type = { \
> > + .sign = 's', \
> > + .realbits = 12, \
> > + .storagebits = 16, \
> > + .shift = 4, \
> > + .endianness = IIO_BE, \
> > + }, \
> > +}
> > +
> > +#define FXLS8962AF_TEMP_CHANNEL { \
> > + .type = IIO_TEMP, \
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
> > + BIT(IIO_CHAN_INFO_OFFSET),\
> > + .scan_index = -1, \
> > + .scan_type = { \
> > + .realbits = 8, \
> > + }, \
> > +}
> > +
> > +static const struct iio_chan_spec fxls8962af_channels[] = {
> > + FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
> > + FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
> > + FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
> > + IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
> > + FXLS8962AF_TEMP_CHANNEL,
> > +};
> > +
> > +static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
> > + [fxls8962af] = {
> > + .chip_id = FXLS8962AF_DEVICE_ID,
> > + .name = "fxls8962af",
> > + .channels = fxls8962af_channels,
> > + .num_channels = ARRAY_SIZE(fxls8962af_channels),
> > + },
> > + [fxls8964af] = {
> > + .chip_id = FXLS8964AF_DEVICE_ID,
> > + .name = "fxls8964af",
> > + .channels = fxls8962af_channels,
> > + .num_channels = ARRAY_SIZE(fxls8962af_channels),
> > + },
> > +};
> > +
> > +static const struct iio_info fxls8962af_info = {
> > + .read_raw = &fxls8962af_read_raw,
> > + .write_raw = &fxls8962af_write_raw,
> > + .write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
> > + .read_avail = fxls8962af_read_avail,
> > +};
> > +
> > +static int fxls8962af_reset(struct fxls8962af_data *data)
> > +{
> > + struct device *dev = regmap_get_device(data->regmap);
> > + unsigned int reg;
> > + int ret;
> > +
> > + ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
> > + FXLS8962AF_SENS_CONFIG1_RST,
> > + FXLS8962AF_SENS_CONFIG1_RST);
> > + if (ret < 0)
> > + return ret;
> > +
> > + /* TBOOT1, TBOOT2, specifies we have to wait between 1 - 17.7ms */
> > + ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_SENS_CONFIG1, reg,
> > + !(reg & FXLS8962AF_SENS_CONFIG1_RST), 1000, 18000);
> > + if (ret) {
> > + dev_err(dev, "reset timeout, sens_config1 = 0x%x\n", reg);
>
> > + return ret;
> > + }
>
> These two lines are redundant.
>
> > +
> > + return ret;
> > +}
> > +
> > +static void fxls8962af_regulator_disable(void *data_ptr)
> > +{
> > + struct fxls8962af_data *data = data_ptr;
> > +
> > + regulator_disable(data->vdd_reg);
> > +}
> > +
> > +static void fxls8962af_pm_disable(void *dev_ptr)
> > +{
> > + struct device *dev = dev_ptr;
> > + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > +
> > + pm_runtime_disable(dev);
> > + pm_runtime_set_suspended(dev);
> > + pm_runtime_put_noidle(dev);
> > +
> > + fxls8962af_standby(iio_priv(indio_dev));
> > +}
> > +
> > +int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
You pass in irq, but don't currently do anything with it.
I guess you probably plan to add optional interrupt support as
a follow up? If that is expected soon I don't mind leaving this here, but
if it's not something we expect to see I'd rather see the parameter dropped and
re added if someone eventually adds interrupt support.
If you do plan to add it, just add a comment in the patch description to
say that.
> > +{
> > + struct fxls8962af_data *data;
> > + struct iio_dev *indio_dev;
> > + unsigned int reg;
> > + int ret, i;
> > +
> > + indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + data = iio_priv(indio_dev);
> > + dev_set_drvdata(dev, indio_dev);
> > + data->regmap = regmap;
> > +
> > + ret = iio_read_mount_matrix(dev, "mount-matrix", &data->orientation);
> > + if (ret)
> > + return ret;
> > +
> > + data->vdd_reg = devm_regulator_get(dev, "vdd");
> > + if (IS_ERR(data->vdd_reg))
> > + return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
> > + "Failed to get vdd regulator\n");
> > +
> > + ret = regulator_enable(data->vdd_reg);
> > + if (ret) {
> > + dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
> > + if (ret)
> > + return ret;
> > +
> > + ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, ®);
> > + if (ret < 0)
> > + return ret;
> > +
> > + for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
> > + if (fxls_chip_info_table[i].chip_id == reg) {
> > + data->chip_info = &fxls_chip_info_table[i];
> > + break;
> > + }
> > + }
> > + if (i == ARRAY_SIZE(fxls_chip_info_table)) {
> > + dev_err(dev, "failed to match device in table\n");
> > + return -ENXIO;
> > + }
> > +
> > + indio_dev->channels = data->chip_info->channels;
> > + indio_dev->num_channels = data->chip_info->num_channels;
> > + indio_dev->name = data->chip_info->name;
> > + indio_dev->info = &fxls8962af_info;
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > +
> > + ret = fxls8962af_reset(data);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = pm_runtime_set_active(dev);
> > + if (ret < 0)
> > + return ret;
> > +
> > + pm_runtime_enable(dev);
> > + pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
> > + pm_runtime_use_autosuspend(dev);
> > +
> > + ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
> > + if (ret)
> > + return ret;
> > +
> > + return devm_iio_device_register(dev, indio_dev);
> > +}
> > +EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
> > +
> > +static int __maybe_unused fxls8962af_runtime_suspend(struct device *dev)
> > +{
> > + struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
> > + int ret;
> > +
> > + ret = fxls8962af_standby(data);
> > + if (ret < 0) {
> > + dev_err(dev, "powering off device failed\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused fxls8962af_runtime_resume(struct device *dev)
> > +{
> > + struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
> > +
> > + return fxls8962af_active(data);
> > +}
> > +
> > +const struct dev_pm_ops fxls8962af_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> > + pm_runtime_force_resume)
> > + SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
> > + fxls8962af_runtime_resume, NULL)
> > +};
> > +EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
> > +
> > +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> > +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/iio/accel/fxls8962af-i2c.c b/drivers/iio/accel/fxls8962af-i2c.c
> > new file mode 100644
> > index 000000000000..0dd86ece46ae
> > --- /dev/null
> > +++ b/drivers/iio/accel/fxls8962af-i2c.c
> > @@ -0,0 +1,57 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver
> > + *
> > + * Copyright 2021 Connected Cars A/S
> > + */
> > +
> > +#include <linux/dev_printk.h>
>
> + err.h
>
> > +#include <linux/i2c.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/regmap.h>
> > +
> > +#include "fxls8962af.h"
> > +
> > +static int fxls8962af_probe(struct i2c_client *client)
> > +{
> > + struct regmap *regmap;
> > +
> > + regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
> > + if (IS_ERR(regmap)) {
> > + dev_err(&client->dev, "Failed to initialize i2c regmap\n");
> > + return PTR_ERR(regmap);
> > + }
> > +
> > + return fxls8962af_core_probe(&client->dev, regmap, client->irq);
> > +}
> > +
> > +static const struct i2c_device_id fxls8962af_id[] = {
> > + {"fxls8962af", fxls8962af},
> > + {"fxls8964af", fxls8964af},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(i2c, fxls8962af_id);
> > +
> > +static const struct of_device_id fxls8962af_of_match[] = {
> > + {.compatible = "nxp,fxls8962af"},
> > + {.compatible = "nxp,fxls8964af"},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, fxls8962af_of_match);
> > +
> > +static struct i2c_driver fxls8962af_driver = {
> > + .driver = {
> > + .name = "fxls8962af_i2c",
> > + .of_match_table = fxls8962af_of_match,
> > + .pm = &fxls8962af_pm_ops,
> > + },
> > + .probe_new = fxls8962af_probe,
> > + .id_table = fxls8962af_id,
> > +};
>
> > +
>
> No need a blank line here.
>
> > +module_i2c_driver(fxls8962af_driver);
> > +
> > +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> > +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer i2c driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/iio/accel/fxls8962af-spi.c b/drivers/iio/accel/fxls8962af-spi.c
> > new file mode 100644
> > index 000000000000..0597c3fef504
> > --- /dev/null
> > +++ b/drivers/iio/accel/fxls8962af-spi.c
> > @@ -0,0 +1,57 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver
> > + *
> > + * Copyright 2021 Connected Cars A/S
> > + */
> > +
> > +#include <linux/dev_printk.h>
>
> + err.h
> + mod_devicetable.h
>
> > +#include <linux/module.h>
> > +#include <linux/spi/spi.h>
>
> > +//#include <linux/slab.h>
>
> ???
>
> Remove it.
>
> > +#include <linux/regmap.h>
> > +
> > +#include "fxls8962af.h"
> > +
> > +static int fxls8962af_probe(struct spi_device *spi)
> > +{
> > + struct regmap *regmap;
> > +
> > + regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
> > + if (IS_ERR(regmap)) {
> > + dev_err(&spi->dev, "Failed to initialize spi regmap\n");
> > + return PTR_ERR(regmap);
> > + }
> > +
> > + return fxls8962af_core_probe(&spi->dev, regmap, spi->irq);
> > +}
> > +
> > +static const struct of_device_id fxls8962af_spi_of_match[] = {
> > + {.compatible = "nxp,fxls8962af"},
> > + {.compatible = "nxp,fxls8964af"},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, fxls8962af_spi_of_match);
> > +
> > +static const struct spi_device_id fxls8962af_spi_id_table[] = {
> > + {"fxls8962af", fxls8962af},
> > + {"fxls8964af", fxls8964af},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(spi, fxls8962af_spi_id_table);
> > +
> > +static struct spi_driver fxls8962af_driver = {
> > + .driver = {
> > + .name = "fxls8962af_spi",
> > + .pm = &fxls8962af_pm_ops,
> > + .of_match_table = fxls8962af_spi_of_match,
> > + },
> > + .probe = fxls8962af_probe,
> > + .id_table = fxls8962af_spi_id_table,
> > +};
>
> > +
>
> No need to have a blank line here.
>
> > +module_spi_driver(fxls8962af_driver);
> > +
> > +MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
> > +MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer spi driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/iio/accel/fxls8962af.h b/drivers/iio/accel/fxls8962af.h
> > new file mode 100644
> > index 000000000000..1dc3b0e317dc
> > --- /dev/null
> > +++ b/drivers/iio/accel/fxls8962af.h
> > @@ -0,0 +1,21 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright 2021 Connected Cars A/S
> > + */
> > +#ifndef _FXLS8962AF_H_
> > +#define _FXLS8962AF_H_
> > +
> > +struct regmap;
> > +struct device;
> > +
> > +enum {
> > + fxls8962af,
> > + fxls8964af,
> > +};
> > +
> > +int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq);
> > +int fxls8962af_core_remove(struct device *dev);
>
> + blank line?
>
> > +extern const struct dev_pm_ops fxls8962af_pm_ops;
> > +extern const struct regmap_config fxls8962af_regmap_conf;
> > +
> > +#endif /* _FXLS8962AF_H_ */
> > --
> > 2.31.0
> >
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers
2021-04-23 12:51 ` [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Andy Shevchenko
2021-04-24 10:43 ` Jonathan Cameron
@ 2021-04-27 15:11 ` Sean Nyekjaer
2021-04-27 15:30 ` Andy Shevchenko
1 sibling, 1 reply; 7+ messages in thread
From: Sean Nyekjaer @ 2021-04-27 15:11 UTC (permalink / raw)
To: Andy Shevchenko
Cc: Jonathan Cameron, linux-iio, Lars-Peter Clausen, Nuno Sá,
Rob Herring, devicetree
On 23/04/2021 14.51, Andy Shevchenko wrote:
>> + default:
>> + ret = -EINVAL;
>> + break;
> return -EINVAL;
>
>> + }
>> +
>> + iio_device_release_direct_mode(indio_dev);
Hi Andy,
Thanks for the review :)
Will have to set ret in order to clear the direct_mode();
/Sean
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers
2021-04-27 15:11 ` Sean Nyekjaer
@ 2021-04-27 15:30 ` Andy Shevchenko
0 siblings, 0 replies; 7+ messages in thread
From: Andy Shevchenko @ 2021-04-27 15:30 UTC (permalink / raw)
To: Sean Nyekjaer
Cc: Jonathan Cameron, linux-iio, Lars-Peter Clausen, Nuno Sá,
Rob Herring, devicetree
On Tue, Apr 27, 2021 at 6:11 PM Sean Nyekjaer <sean@geanix.com> wrote:
> On 23/04/2021 14.51, Andy Shevchenko wrote:
> >> + default:
> >> + ret = -EINVAL;
> >> + break;
> > return -EINVAL;
> >
> >> + }
> >> +
> >> + iio_device_release_direct_mode(indio_dev);
> Hi Andy,
>
> Thanks for the review :)
> Will have to set ret in order to clear the direct_mode();
Right, thanks for clarifying!
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-04-27 15:31 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-23 10:19 [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Sean Nyekjaer
2021-04-23 10:19 ` [PATCH v2 2/2] dt-bindings: iio: accel: fxls8962af: add bindings Sean Nyekjaer
2021-04-24 10:29 ` Jonathan Cameron
2021-04-23 12:51 ` [PATCH v2 1/2] iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers Andy Shevchenko
2021-04-24 10:43 ` Jonathan Cameron
2021-04-27 15:11 ` Sean Nyekjaer
2021-04-27 15:30 ` Andy Shevchenko
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.