All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 1/2] drm/bridge: anx7625: refactor power control to use runtime PM framework
@ 2021-05-07  6:35 ` Pi-Hsun Shih
  0 siblings, 0 replies; 4+ messages in thread
From: Pi-Hsun Shih @ 2021-05-07  6:35 UTC (permalink / raw)
  Cc: Pi-Hsun Shih, Tzung-Bi Shih, Andrzej Hajda, Neil Armstrong,
	Robert Foss, Laurent Pinchart, Jonas Karlman, Jernej Skrabec,
	David Airlie, Daniel Vetter, Xin Ji, Hsin-Yi Wang, Sam Ravnborg,
	open list:DRM DRIVERS, open list

The driver originally use an atomic_t for keep track of the power
status, which makes the driver more complicated than needed, and has
some race condition as it's possible to have the power on and power off
sequence going at the same time.

This patch remove the usage of the atomic_t power_status, and use the
kernel runtime power management framework instead.

Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I58e19680b6d9ffb04be2a90f458400a1433925aa
---
 drivers/gpu/drm/bridge/analogix/anx7625.c | 147 +++++++++-------------
 drivers/gpu/drm/bridge/analogix/anx7625.h |   1 -
 2 files changed, 62 insertions(+), 86 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 23283ba0c4f9..0d90cd63fc27 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/types.h>
@@ -1005,33 +1006,6 @@ static void anx7625_power_on_init(struct anx7625_data *ctx)
 	}
 }
 
-static void anx7625_chip_control(struct anx7625_data *ctx, int state)
-{
-	struct device *dev = &ctx->client->dev;
-
-	DRM_DEV_DEBUG_DRIVER(dev, "before set, power_state(%d).\n",
-			     atomic_read(&ctx->power_status));
-
-	if (!ctx->pdata.low_power_mode)
-		return;
-
-	if (state) {
-		atomic_inc(&ctx->power_status);
-		if (atomic_read(&ctx->power_status) == 1)
-			anx7625_power_on_init(ctx);
-	} else {
-		if (atomic_read(&ctx->power_status)) {
-			atomic_dec(&ctx->power_status);
-
-			if (atomic_read(&ctx->power_status) == 0)
-				anx7625_power_standby(ctx);
-		}
-	}
-
-	DRM_DEV_DEBUG_DRIVER(dev, "after set, power_state(%d).\n",
-			     atomic_read(&ctx->power_status));
-}
-
 static void anx7625_init_gpio(struct anx7625_data *platform)
 {
 	struct device *dev = &platform->client->dev;
@@ -1061,9 +1035,6 @@ static void anx7625_stop_dp_work(struct anx7625_data *ctx)
 	ctx->hpd_status = 0;
 	ctx->hpd_high_cnt = 0;
 	ctx->display_timing_valid = 0;
-
-	if (ctx->pdata.low_power_mode == 0)
-		anx7625_disable_pd_protocol(ctx);
 }
 
 static void anx7625_start_dp_work(struct anx7625_data *ctx)
@@ -1105,49 +1076,26 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
 	int ret, val;
 	struct device *dev = &ctx->client->dev;
 
-	if (atomic_read(&ctx->power_status) != 1) {
-		DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
-		return;
-	}
-
 	ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
 				 ctx, val,
 				 ((val & HPD_STATUS) || (val < 0)),
 				 5000,
 				 5000 * 100);
 	if (ret) {
-		DRM_DEV_ERROR(dev, "HPD polling timeout!\n");
-	} else {
-		DRM_DEV_DEBUG_DRIVER(dev, "HPD raise up.\n");
-		anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
-				  INTR_ALERT_1, 0xFF);
-		anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
-				  INTERFACE_CHANGE_INT, 0);
+		DRM_DEV_ERROR(dev, "no hpd.\n");
+		return;
 	}
 
-	anx7625_start_dp_work(ctx);
-}
-
-static void anx7625_disconnect_check(struct anx7625_data *ctx)
-{
-	if (atomic_read(&ctx->power_status) == 0)
-		anx7625_stop_dp_work(ctx);
-}
-
-static void anx7625_low_power_mode_check(struct anx7625_data *ctx,
-					 int state)
-{
-	struct device *dev = &ctx->client->dev;
+	DRM_DEV_DEBUG_DRIVER(dev, "system status: 0x%x. HPD raise up.\n", val);
+	anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+			  INTR_ALERT_1, 0xFF);
+	anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+			  INTERFACE_CHANGE_INT, 0);
 
-	DRM_DEV_DEBUG_DRIVER(dev, "low power mode check, state(%d).\n", state);
+	anx7625_start_dp_work(ctx);
 
-	if (ctx->pdata.low_power_mode) {
-		anx7625_chip_control(ctx, state);
-		if (state)
-			anx7625_hpd_polling(ctx);
-		else
-			anx7625_disconnect_check(ctx);
-	}
+	if (!ctx->pdata.panel_bridge && ctx->bridge_attached)
+		drm_helper_hpd_irq_event(ctx->bridge.dev);
 }
 
 static void anx7625_remove_edid(struct anx7625_data *ctx)
@@ -1180,9 +1128,6 @@ static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
 	int intr_vector, status;
 	struct device *dev = &ctx->client->dev;
 
-	DRM_DEV_DEBUG_DRIVER(dev, "power_status=%d\n",
-			     (u32)atomic_read(&ctx->power_status));
-
 	status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
 				   INTR_ALERT_1, 0xFF);
 	if (status < 0) {
@@ -1228,22 +1173,25 @@ static void anx7625_work_func(struct work_struct *work)
 						struct anx7625_data, work);
 
 	mutex_lock(&ctx->lock);
+
+	if (pm_runtime_suspended(&ctx->client->dev))
+		goto unlock;
+
 	event = anx7625_hpd_change_detect(ctx);
-	mutex_unlock(&ctx->lock);
 	if (event < 0)
-		return;
+		goto unlock;
 
 	if (ctx->bridge_attached)
 		drm_helper_hpd_irq_event(ctx->bridge.dev);
+
+unlock:
+	mutex_unlock(&ctx->lock);
 }
 
 static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
 {
 	struct anx7625_data *ctx = (struct anx7625_data *)data;
 
-	if (atomic_read(&ctx->power_status) != 1)
-		return IRQ_NONE;
-
 	queue_work(ctx->workqueue, &ctx->work);
 
 	return IRQ_HANDLED;
@@ -1305,9 +1253,9 @@ static struct edid *anx7625_get_edid(struct anx7625_data *ctx)
 		return (struct edid *)edid;
 	}
 
-	anx7625_low_power_mode_check(ctx, 1);
+	pm_runtime_get_sync(dev);
 	edid_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data);
-	anx7625_low_power_mode_check(ctx, 0);
+	pm_runtime_put(dev);
 
 	if (edid_num < 1) {
 		DRM_DEV_ERROR(dev, "Fail to read EDID: %d\n", edid_num);
@@ -1611,10 +1559,7 @@ static void anx7625_bridge_enable(struct drm_bridge *bridge)
 
 	DRM_DEV_DEBUG_DRIVER(dev, "drm enable\n");
 
-	anx7625_low_power_mode_check(ctx, 1);
-
-	if (WARN_ON(!atomic_read(&ctx->power_status)))
-		return;
+	pm_runtime_get_sync(dev);
 
 	anx7625_dp_start(ctx);
 }
@@ -1624,14 +1569,11 @@ static void anx7625_bridge_disable(struct drm_bridge *bridge)
 	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
 	struct device *dev = &ctx->client->dev;
 
-	if (WARN_ON(!atomic_read(&ctx->power_status)))
-		return;
-
 	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
 
 	anx7625_dp_stop(ctx);
 
-	anx7625_low_power_mode_check(ctx, 0);
+	pm_runtime_put(dev);
 }
 
 static enum drm_connector_status
@@ -1735,6 +1677,38 @@ static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx)
 	i2c_unregister_device(ctx->i2c.tcpc_client);
 }
 
+static int __maybe_unused anx7625_runtime_pm_suspend(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	mutex_lock(&ctx->lock);
+
+	anx7625_stop_dp_work(ctx);
+	anx7625_power_standby(ctx);
+
+	mutex_unlock(&ctx->lock);
+
+	return 0;
+}
+
+static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	mutex_lock(&ctx->lock);
+
+	anx7625_power_on_init(ctx);
+	anx7625_hpd_polling(ctx);
+
+	mutex_unlock(&ctx->lock);
+
+	return 0;
+}
+
+static const struct dev_pm_ops anx7625_pm_ops = {
+	SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, anx7625_runtime_pm_resume, NULL)
+};
+
 static int anx7625_i2c_probe(struct i2c_client *client,
 			     const struct i2c_device_id *id)
 {
@@ -1778,8 +1752,6 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 	}
 	anx7625_init_gpio(platform);
 
-	atomic_set(&platform->power_status, 0);
-
 	mutex_init(&platform->lock);
 
 	platform->pdata.intp_irq = client->irq;
@@ -1809,9 +1781,11 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 		goto free_wq;
 	}
 
-	if (platform->pdata.low_power_mode == 0) {
+	pm_runtime_enable(dev);
+
+	if (!platform->pdata.low_power_mode) {
 		anx7625_disable_pd_protocol(platform);
-		atomic_set(&platform->power_status, 1);
+		pm_runtime_get_sync(dev);
 	}
 
 	/* Add work function */
@@ -1847,6 +1821,9 @@ static int anx7625_i2c_remove(struct i2c_client *client)
 	if (platform->pdata.intp_irq)
 		destroy_workqueue(platform->workqueue);
 
+	if (!platform->pdata.low_power_mode)
+		pm_runtime_put_sync_suspend(&client->dev);
+
 	anx7625_unregister_i2c_dummy_clients(platform);
 
 	kfree(platform);
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
index e4a086b3a3d7..034c3840028f 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.h
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -369,7 +369,6 @@ struct anx7625_i2c_client {
 
 struct anx7625_data {
 	struct anx7625_platform_data pdata;
-	atomic_t power_status;
 	int hpd_status;
 	int hpd_high_cnt;
 	/* Lock for work queue */

base-commit: e48661230cc35b3d0f4367eddfc19f86463ab917
-- 
2.31.1.607.g51e8a6a459-goog


^ permalink raw reply related	[flat|nested] 4+ messages in thread
* [PATCH 1/2] drm/bridge: anx7625: refactor power control to use runtime PM framework
@ 2021-05-07  6:35 ` Pi-Hsun Shih
  0 siblings, 0 replies; 4+ messages in thread
From: Pi-Hsun Shih @ 2021-05-07  6:35 UTC (permalink / raw)
  Cc: Jernej Skrabec, Neil Armstrong, David Airlie,
	open list:DRM DRIVERS, Jonas Karlman, open list, Robert Foss,
	Andrzej Hajda, Tzung-Bi Shih, Laurent Pinchart, Pi-Hsun Shih,
	Hsin-Yi Wang, Sam Ravnborg, Xin Ji

The driver originally use an atomic_t for keep track of the power
status, which makes the driver more complicated than needed, and has
some race condition as it's possible to have the power on and power off
sequence going at the same time.

This patch remove the usage of the atomic_t power_status, and use the
kernel runtime power management framework instead.

Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I58e19680b6d9ffb04be2a90f458400a1433925aa
---
 drivers/gpu/drm/bridge/analogix/anx7625.c | 147 +++++++++-------------
 drivers/gpu/drm/bridge/analogix/anx7625.h |   1 -
 2 files changed, 62 insertions(+), 86 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 23283ba0c4f9..0d90cd63fc27 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/types.h>
@@ -1005,33 +1006,6 @@ static void anx7625_power_on_init(struct anx7625_data *ctx)
 	}
 }
 
-static void anx7625_chip_control(struct anx7625_data *ctx, int state)
-{
-	struct device *dev = &ctx->client->dev;
-
-	DRM_DEV_DEBUG_DRIVER(dev, "before set, power_state(%d).\n",
-			     atomic_read(&ctx->power_status));
-
-	if (!ctx->pdata.low_power_mode)
-		return;
-
-	if (state) {
-		atomic_inc(&ctx->power_status);
-		if (atomic_read(&ctx->power_status) == 1)
-			anx7625_power_on_init(ctx);
-	} else {
-		if (atomic_read(&ctx->power_status)) {
-			atomic_dec(&ctx->power_status);
-
-			if (atomic_read(&ctx->power_status) == 0)
-				anx7625_power_standby(ctx);
-		}
-	}
-
-	DRM_DEV_DEBUG_DRIVER(dev, "after set, power_state(%d).\n",
-			     atomic_read(&ctx->power_status));
-}
-
 static void anx7625_init_gpio(struct anx7625_data *platform)
 {
 	struct device *dev = &platform->client->dev;
@@ -1061,9 +1035,6 @@ static void anx7625_stop_dp_work(struct anx7625_data *ctx)
 	ctx->hpd_status = 0;
 	ctx->hpd_high_cnt = 0;
 	ctx->display_timing_valid = 0;
-
-	if (ctx->pdata.low_power_mode == 0)
-		anx7625_disable_pd_protocol(ctx);
 }
 
 static void anx7625_start_dp_work(struct anx7625_data *ctx)
@@ -1105,49 +1076,26 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
 	int ret, val;
 	struct device *dev = &ctx->client->dev;
 
-	if (atomic_read(&ctx->power_status) != 1) {
-		DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
-		return;
-	}
-
 	ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
 				 ctx, val,
 				 ((val & HPD_STATUS) || (val < 0)),
 				 5000,
 				 5000 * 100);
 	if (ret) {
-		DRM_DEV_ERROR(dev, "HPD polling timeout!\n");
-	} else {
-		DRM_DEV_DEBUG_DRIVER(dev, "HPD raise up.\n");
-		anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
-				  INTR_ALERT_1, 0xFF);
-		anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
-				  INTERFACE_CHANGE_INT, 0);
+		DRM_DEV_ERROR(dev, "no hpd.\n");
+		return;
 	}
 
-	anx7625_start_dp_work(ctx);
-}
-
-static void anx7625_disconnect_check(struct anx7625_data *ctx)
-{
-	if (atomic_read(&ctx->power_status) == 0)
-		anx7625_stop_dp_work(ctx);
-}
-
-static void anx7625_low_power_mode_check(struct anx7625_data *ctx,
-					 int state)
-{
-	struct device *dev = &ctx->client->dev;
+	DRM_DEV_DEBUG_DRIVER(dev, "system status: 0x%x. HPD raise up.\n", val);
+	anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+			  INTR_ALERT_1, 0xFF);
+	anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+			  INTERFACE_CHANGE_INT, 0);
 
-	DRM_DEV_DEBUG_DRIVER(dev, "low power mode check, state(%d).\n", state);
+	anx7625_start_dp_work(ctx);
 
-	if (ctx->pdata.low_power_mode) {
-		anx7625_chip_control(ctx, state);
-		if (state)
-			anx7625_hpd_polling(ctx);
-		else
-			anx7625_disconnect_check(ctx);
-	}
+	if (!ctx->pdata.panel_bridge && ctx->bridge_attached)
+		drm_helper_hpd_irq_event(ctx->bridge.dev);
 }
 
 static void anx7625_remove_edid(struct anx7625_data *ctx)
@@ -1180,9 +1128,6 @@ static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
 	int intr_vector, status;
 	struct device *dev = &ctx->client->dev;
 
-	DRM_DEV_DEBUG_DRIVER(dev, "power_status=%d\n",
-			     (u32)atomic_read(&ctx->power_status));
-
 	status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
 				   INTR_ALERT_1, 0xFF);
 	if (status < 0) {
@@ -1228,22 +1173,25 @@ static void anx7625_work_func(struct work_struct *work)
 						struct anx7625_data, work);
 
 	mutex_lock(&ctx->lock);
+
+	if (pm_runtime_suspended(&ctx->client->dev))
+		goto unlock;
+
 	event = anx7625_hpd_change_detect(ctx);
-	mutex_unlock(&ctx->lock);
 	if (event < 0)
-		return;
+		goto unlock;
 
 	if (ctx->bridge_attached)
 		drm_helper_hpd_irq_event(ctx->bridge.dev);
+
+unlock:
+	mutex_unlock(&ctx->lock);
 }
 
 static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
 {
 	struct anx7625_data *ctx = (struct anx7625_data *)data;
 
-	if (atomic_read(&ctx->power_status) != 1)
-		return IRQ_NONE;
-
 	queue_work(ctx->workqueue, &ctx->work);
 
 	return IRQ_HANDLED;
@@ -1305,9 +1253,9 @@ static struct edid *anx7625_get_edid(struct anx7625_data *ctx)
 		return (struct edid *)edid;
 	}
 
-	anx7625_low_power_mode_check(ctx, 1);
+	pm_runtime_get_sync(dev);
 	edid_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data);
-	anx7625_low_power_mode_check(ctx, 0);
+	pm_runtime_put(dev);
 
 	if (edid_num < 1) {
 		DRM_DEV_ERROR(dev, "Fail to read EDID: %d\n", edid_num);
@@ -1611,10 +1559,7 @@ static void anx7625_bridge_enable(struct drm_bridge *bridge)
 
 	DRM_DEV_DEBUG_DRIVER(dev, "drm enable\n");
 
-	anx7625_low_power_mode_check(ctx, 1);
-
-	if (WARN_ON(!atomic_read(&ctx->power_status)))
-		return;
+	pm_runtime_get_sync(dev);
 
 	anx7625_dp_start(ctx);
 }
@@ -1624,14 +1569,11 @@ static void anx7625_bridge_disable(struct drm_bridge *bridge)
 	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
 	struct device *dev = &ctx->client->dev;
 
-	if (WARN_ON(!atomic_read(&ctx->power_status)))
-		return;
-
 	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
 
 	anx7625_dp_stop(ctx);
 
-	anx7625_low_power_mode_check(ctx, 0);
+	pm_runtime_put(dev);
 }
 
 static enum drm_connector_status
@@ -1735,6 +1677,38 @@ static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx)
 	i2c_unregister_device(ctx->i2c.tcpc_client);
 }
 
+static int __maybe_unused anx7625_runtime_pm_suspend(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	mutex_lock(&ctx->lock);
+
+	anx7625_stop_dp_work(ctx);
+	anx7625_power_standby(ctx);
+
+	mutex_unlock(&ctx->lock);
+
+	return 0;
+}
+
+static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	mutex_lock(&ctx->lock);
+
+	anx7625_power_on_init(ctx);
+	anx7625_hpd_polling(ctx);
+
+	mutex_unlock(&ctx->lock);
+
+	return 0;
+}
+
+static const struct dev_pm_ops anx7625_pm_ops = {
+	SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, anx7625_runtime_pm_resume, NULL)
+};
+
 static int anx7625_i2c_probe(struct i2c_client *client,
 			     const struct i2c_device_id *id)
 {
@@ -1778,8 +1752,6 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 	}
 	anx7625_init_gpio(platform);
 
-	atomic_set(&platform->power_status, 0);
-
 	mutex_init(&platform->lock);
 
 	platform->pdata.intp_irq = client->irq;
@@ -1809,9 +1781,11 @@ static int anx7625_i2c_probe(struct i2c_client *client,
 		goto free_wq;
 	}
 
-	if (platform->pdata.low_power_mode == 0) {
+	pm_runtime_enable(dev);
+
+	if (!platform->pdata.low_power_mode) {
 		anx7625_disable_pd_protocol(platform);
-		atomic_set(&platform->power_status, 1);
+		pm_runtime_get_sync(dev);
 	}
 
 	/* Add work function */
@@ -1847,6 +1821,9 @@ static int anx7625_i2c_remove(struct i2c_client *client)
 	if (platform->pdata.intp_irq)
 		destroy_workqueue(platform->workqueue);
 
+	if (!platform->pdata.low_power_mode)
+		pm_runtime_put_sync_suspend(&client->dev);
+
 	anx7625_unregister_i2c_dummy_clients(platform);
 
 	kfree(platform);
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
index e4a086b3a3d7..034c3840028f 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.h
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -369,7 +369,6 @@ struct anx7625_i2c_client {
 
 struct anx7625_data {
 	struct anx7625_platform_data pdata;
-	atomic_t power_status;
 	int hpd_status;
 	int hpd_high_cnt;
 	/* Lock for work queue */

base-commit: e48661230cc35b3d0f4367eddfc19f86463ab917
-- 
2.31.1.607.g51e8a6a459-goog


^ permalink raw reply related	[flat|nested] 4+ messages in thread
* [PATCH 2/2] drm/bridge: anx7625: add suspend / resume hooks
  2021-05-07  6:35 ` Pi-Hsun Shih
@ 2021-05-07  6:35   ` Pi-Hsun Shih
  -1 siblings, 0 replies; 4+ messages in thread
From: Pi-Hsun Shih @ 2021-05-07  6:35 UTC (permalink / raw)
  Cc: Pi-Hsun Shih, Tzung-Bi Shih, Andrzej Hajda, Neil Armstrong,
	Robert Foss, Laurent Pinchart, Jonas Karlman, Jernej Skrabec,
	David Airlie, Daniel Vetter, Xin Ji, Sam Ravnborg, Hsin-Yi Wang,
	open list:DRM DRIVERS, open list

Add suspend / resume hooks for anx7625 driver, that power off the device
on suspend and power on the device on resume if it was previously
powered.

Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I62122cc2a4eafdfce4859cbb419edc39875ebe3b
---
 drivers/gpu/drm/bridge/analogix/anx7625.c | 27 +++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 0d90cd63fc27..dd23db9bc3d4 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -1705,7 +1705,34 @@ static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev)
 	return 0;
 }
 
+static int __maybe_unused anx7625_resume(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	if (!ctx->pdata.intp_irq)
+		return 0;
+
+	if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev))
+		anx7625_runtime_pm_resume(dev);
+
+	return 0;
+}
+
+static int __maybe_unused anx7625_suspend(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	if (!ctx->pdata.intp_irq)
+		return 0;
+
+	if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev))
+		anx7625_runtime_pm_suspend(dev);
+
+	return 0;
+}
+
 static const struct dev_pm_ops anx7625_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(anx7625_suspend, anx7625_resume) \
 	SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, anx7625_runtime_pm_resume, NULL)
 };
 
-- 
2.31.1.607.g51e8a6a459-goog


^ permalink raw reply related	[flat|nested] 4+ messages in thread
* [PATCH 2/2] drm/bridge: anx7625: add suspend / resume hooks
@ 2021-05-07  6:35   ` Pi-Hsun Shih
  0 siblings, 0 replies; 4+ messages in thread
From: Pi-Hsun Shih @ 2021-05-07  6:35 UTC (permalink / raw)
  Cc: Jernej Skrabec, Neil Armstrong, David Airlie,
	open list:DRM DRIVERS, Jonas Karlman, open list, Robert Foss,
	Andrzej Hajda, Tzung-Bi Shih, Laurent Pinchart, Pi-Hsun Shih,
	Hsin-Yi Wang, Sam Ravnborg, Xin Ji

Add suspend / resume hooks for anx7625 driver, that power off the device
on suspend and power on the device on resume if it was previously
powered.

Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I62122cc2a4eafdfce4859cbb419edc39875ebe3b
---
 drivers/gpu/drm/bridge/analogix/anx7625.c | 27 +++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 0d90cd63fc27..dd23db9bc3d4 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -1705,7 +1705,34 @@ static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev)
 	return 0;
 }
 
+static int __maybe_unused anx7625_resume(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	if (!ctx->pdata.intp_irq)
+		return 0;
+
+	if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev))
+		anx7625_runtime_pm_resume(dev);
+
+	return 0;
+}
+
+static int __maybe_unused anx7625_suspend(struct device *dev)
+{
+	struct anx7625_data *ctx = dev_get_drvdata(dev);
+
+	if (!ctx->pdata.intp_irq)
+		return 0;
+
+	if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev))
+		anx7625_runtime_pm_suspend(dev);
+
+	return 0;
+}
+
 static const struct dev_pm_ops anx7625_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(anx7625_suspend, anx7625_resume) \
 	SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, anx7625_runtime_pm_resume, NULL)
 };
 
-- 
2.31.1.607.g51e8a6a459-goog


^ permalink raw reply related	[flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-05-07  7:04 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-07  6:35 [PATCH 1/2] drm/bridge: anx7625: refactor power control to use runtime PM framework Pi-Hsun Shih
2021-05-07  6:35 ` Pi-Hsun Shih
2021-05-07  6:35 ` [PATCH 2/2] drm/bridge: anx7625: add suspend / resume hooks Pi-Hsun Shih
2021-05-07  6:35   ` Pi-Hsun Shih

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.