[Buildroot] [git commit] configs/beaglev: enable building of low-level firmware

[Buildroot] [git commit] configs/beaglev: enable building of low-level firmware

[Yann E. MORIN]

commit: https://git.buildroot.net/buildroot/commit/?id=671423d33e301c1c6e9186926a22980bb7597440
branch: https://git.buildroot.net/buildroot/commit/?id=refs/heads/master

This commit extends the beaglev_defconfig and its documentation to
build the low-level firmware, and to explain how to reflash it.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[yann.morin.1998 at free.fr: use typoed-name for beaglev-ddrlnit]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
---
 board/beaglev/readme.txt  | 38 ++++++++++++++++++++++++++++++++++++--
 configs/beaglev_defconfig |  2 ++
 2 files changed, 38 insertions(+), 2 deletions(-)

diff --git a/board/beaglev/readme.txt b/board/beaglev/readme.txt
index d8511d3fd1..bbdb9b12ef 100644
--- a/board/beaglev/readme.txt
+++ b/board/beaglev/readme.txt
@@ -17,6 +17,8 @@ Build results
 
 After building, output/images contains:
 
++ bootloader-BEAGLEV-buildroot.bin.out
++ ddrinit-2133-buildroot.bin.out
 + Image
 + fw_payload.bin
 + fw_payload.bin.out
@@ -26,7 +28,11 @@ After building, output/images contains:
 + sdcard.img
 + u-boot.bin
 
-The two important files are:
+The four important files are:
+
+ - bootloader-BEAGLEV-buildroot.bin.out, the first stage bootloader
+
+ - ddrinit-2133-buildroot.bin.out, the DDR initialization firmware
 
  - fw_payload.bin.out, which is the bootloader image, containing
    both OpenSBI and U-Boot.
@@ -51,7 +57,7 @@ Insert your SD card.
 
 Power-up the board using an USB-C cable.
 
-Flashing the bootloader
+Flashing OpenSBI/U-Boot
 =======================
 
 The bootloader pre-flashed on the Beagle-V has a non-working
@@ -86,3 +92,31 @@ fw_payload.bin.out using the Xmodem protocol.
 
 After reflashing is complete, restart the board, it will automatically
 start the system from the SD card, and reach the login prompt.
+
+Flashing low-level bootloaders
+==============================
+
+The BeagleV comes pre-flashed with functional low-level bootloaders
+(called "secondboot" and "ddrinit"). Re-flashing them is not necessary
+to use this Buildroot defconfig. However, for the sake of
+completeness, Buildroot builds and provides those low-level bootloader
+images.
+
+You can flash them as follows:
+
+ - In the same "pre-loader" menu as the one used above, instead of
+   entering 0 or 1, enter the magic "root at s5t" string. This enters the
+   "expert" features.
+
+ - Then, press 0 and send over X-modem the
+   bootloader-BEAGLEV-buildroot.bin.out file.
+
+ - Then, press 1 and send over X-modem the
+   ddrinit-2133-buildroot.bin.out.
+
+Note that the reflashing mechanism itself relies on those low-level
+bootloaders, so if you flash non-working versions, you'll have to go
+through a recovery process. This requires wiring up to a separate
+debug UART, which pins are located near the HDMI connector. See
+https://wiki.seeedstudio.com/BeagleV-Update-bootloader-ddr-init-boot-uboot-Recover-bootloader/
+section "Recover the bootloader" for more details.
diff --git a/configs/beaglev_defconfig b/configs/beaglev_defconfig
index e94c4ab639..59051e7a6d 100644
--- a/configs/beaglev_defconfig
+++ b/configs/beaglev_defconfig
@@ -18,6 +18,8 @@ BR2_LINUX_KERNEL_INSTALL_TARGET=y
 BR2_TARGET_ROOTFS_EXT2=y
 BR2_TARGET_ROOTFS_EXT2_4=y
 # BR2_TARGET_ROOTFS_TAR is not set
+BR2_TARGET_BEAGLEV_DDRLNIT=y
+BR2_TARGET_BEAGLEV_SECONDBOOT=y
 BR2_TARGET_OPENSBI=y
 BR2_TARGET_OPENSBI_CUSTOM_TARBALL=y
 # HEAD of the Fedora branch