[PATCH v7] imx: support for conga-QMX8 board

* [PATCH v7] imx: support for conga-QMX8 board
@ 2021-05-31 13:50 Oliver Graute
  2021-06-09 13:43 ` sbabic
  0 siblings, 1 reply; 2+ messages in thread
From: Oliver Graute @ 2021-05-31 13:50 UTC (permalink / raw)
  To: sbabic
  Cc: peng.fan, festevam, oliver.graute, u-boot, uboot-imx,
	Oliver Graute, Simon Glass, Ye Li, Jagan Teki, Kever Yang,
	Andre Przywara, Patrick Delaunay, Tim Harvey, Peter Robinson,
	Heiko Schocher, Heiko Stuebner, Lokesh Vutla, Igor Opaniuk,
	Oleksandr Suvorov, Clement Faure, Wasim Khan, Priyanka Jain,
	Stephen Carlson, Padmarao Begari, Denis 'GNUtoo' Carikli,
	Neil Armstrong, Michael Walle, Anastasiia Lukianenko,
	Sean Anderson

Add i.MX8QM qmx8 congatec board support

U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Congatec QMX8 Qseven series
Board: conga-QMX8
Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9
Boot:  SD2
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
---

These changes are based on this vendor tree:
git.congatec.com/imx8_early_access/imx8_uboot_internal.git

Changes for v7:
 - removed superflous include in board/congatec/common/mmc.c
 - added congatec to doc/board/index.rst

Changes for v6:
 - fixed build warnings because of missing prototypes

Changes for v5:
 - fixed checkpatch errors
 - fixed some checkpatch warnings

Changes for v4:
 - fixed missing DTS file in MAINTAINERS
 - replaced bd_t with struct bd_info
 - replaced README with imx8qm-dmsse20-a1.rst
 - move CMD_FUSE to Kconfig
 - replaced power_domain_lookup_name with imx8_power_domain_lookup_name

Changes for v3:
 - include log.h
 - include delay.h
 - improved README
 - set phy register to six
 - Remove 'fdt_high' and 'initrd_high' environment variables
 - set CONFIG_SYS_BOOTMAPSZ to 256MB
 - increased CONFIG_SYS_FSL_USDHC_NUM to 3

Changes for v2:
 - added USDHC3_BASE_ADDR
 - replaced CONFIG_FSL_ESDHC with CONFIG_FSL_ESDHC_IMX
 - set CONFIG_FEC_MXC_PHYADDR to -1
 - moved CONFIG_ENV_SIZE and CONFIG_ENV_OFFSET to defconfig

 arch/arm/dts/Makefile               |   1 +
 arch/arm/dts/imx8qm-cgtqmx8.dts     | 404 ++++++++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig      |   7 +
 board/congatec/cgtqmx8/Kconfig      |  14 +
 board/congatec/cgtqmx8/MAINTAINERS  |   7 +
 board/congatec/cgtqmx8/Makefile     |  11 +
 board/congatec/cgtqmx8/cgtqmx8.c    | 460 ++++++++++++++++++++++++++++
 board/congatec/cgtqmx8/imximage.cfg |  21 ++
 board/congatec/cgtqmx8/spl.c        |  77 +++++
 board/congatec/common/Kconfig       |  48 +++
 board/congatec/common/Makefile      |  23 ++
 board/congatec/common/mmc.c         |  49 +++
 configs/cgtqmx8_defconfig           |  86 ++++++
 doc/board/congatec/cgtqmx8.rst      |  70 +++++
 doc/board/congatec/index.rst        |   9 +
 doc/board/index.rst                 |   1 +
 include/configs/cgtqmx8.h           | 181 +++++++++++
 17 files changed, 1469 insertions(+)
 create mode 100644 arch/arm/dts/imx8qm-cgtqmx8.dts
 create mode 100644 board/congatec/cgtqmx8/Kconfig
 create mode 100644 board/congatec/cgtqmx8/MAINTAINERS
 create mode 100644 board/congatec/cgtqmx8/Makefile
 create mode 100644 board/congatec/cgtqmx8/cgtqmx8.c
 create mode 100644 board/congatec/cgtqmx8/imximage.cfg
 create mode 100644 board/congatec/cgtqmx8/spl.c
 create mode 100644 board/congatec/common/Kconfig
 create mode 100644 board/congatec/common/Makefile
 create mode 100644 board/congatec/common/mmc.c
 create mode 100644 configs/cgtqmx8_defconfig
 create mode 100644 doc/board/congatec/cgtqmx8.rst
 create mode 100644 doc/board/congatec/index.rst
 create mode 100644 include/configs/cgtqmx8.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 096068261d..b95960c704 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -836,6 +836,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \
 dtb-$(CONFIG_ARCH_IMX8) += \
 	fsl-imx8qm-apalis.dtb \
 	fsl-imx8qm-mek.dtb \
+	imx8qm-cgtqmx8.dtb \
 	imx8qm-rom7720-a1.dtb \
 	fsl-imx8qxp-ai_ml.dtb \
 	fsl-imx8qxp-colibri.dtb \
diff --git a/arch/arm/dts/imx8qm-cgtqmx8.dts b/arch/arm/dts/imx8qm-cgtqmx8.dts
new file mode 100644
index 0000000000..555c357f6f
--- /dev/null
+++ b/arch/arm/dts/imx8qm-cgtqmx8.dts
@@ -0,0 +1,404 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ * Copyright 2017 congatec AG
+ * Copyright (C) 2019 Oliver Graute <oliver.graute@kococonnector.com>
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+
+/ {
+	model = "Congatec QMX8 Qseven series";
+	compatible = "fsl,imx8qm-qmx8", "fsl,imx8qm";
+
+	chosen {
+		bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200";
+		stdout-path = &lpuart0;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usdhc2_vmmc: usdhc2_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "sw-3p3-sd1";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			off-on-delay-us = <3000>;
+		};
+
+		reg_usdhc3_vmmc: usdhc3_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "sw-3p3-sd2";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			off-on-delay-us = <3000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	fsl,rgmii_txc_dly;
+	fsl,rgmii_rxc_dly;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@6 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <6>;
+			at803x,eee-disabled;
+			at803x,vddio-1p8v;
+		};
+	};
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c0>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc_ext: m41t62@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	wm8904: wm8904@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+
+		clocks = <&clk IMX8QM_AUD_MCLKOUT0>;
+		clock-names = "mclk";
+		wlf,shared-lrclk;
+		/* power-domains = <&pd_mclk_out0>; */
+
+		assigned-clocks = <&clk IMX8QM_AUD_PLL0_DIV>,
+				<&clk IMX8QM_AUD_ACM_AUD_PLL_CLK0_DIV>,
+				<&clk IMX8QM_AUD_ACM_AUD_REC_CLK0_DIV>,
+				<&clk IMX8QM_AUD_MCLKOUT0>;
+
+		assigned-clock-rates = <786432000>, <49152000>, <24576000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx8qm-qmx8 {
+
+		pinctrl_hog: hoggrp{
+			fsl,pins = <
+				SC_P_M40_GPIO0_01_LSIO_GPIO0_IO09		0x00000021
+				SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04		0x00000021
+				SC_P_M40_GPIO0_00_LSIO_GPIO0_IO08		0x00000021
+				SC_P_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000021
+				SC_P_SPDIF0_TX_LSIO_GPIO2_IO15			0x00000021
+				SC_P_FLEXCAN1_RX_LSIO_GPIO3_IO31		0x00000021
+				SC_P_ESAI1_TX0_LSIO_GPIO2_IO08			0x00000021
+				SC_P_FLEXCAN1_TX_LSIO_GPIO4_IO00		0x00000021
+				SC_P_ESAI1_TX1_LSIO_GPIO2_IO09			0x00000021
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				SC_P_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+				SC_P_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+				SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x06000020
+				SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC	0x06000020
+				SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0	0x06000020
+				SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1	0x06000020
+				SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2	0x06000020
+				SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3	0x06000020
+				SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC	0x06000020
+				SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x06000020
+				SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0	0x06000020
+				SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1	0x06000020
+				SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2	0x06000020
+				SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3	0x06000020
+			>;
+		};
+
+		pinctrl_lpi2c0: lpi2c0grp {
+			fsl,pins = <
+				SC_P_HDMI_TX0_TS_SCL_DMA_I2C0_SCL	0xc600004c
+				SC_P_HDMI_TX0_TS_SDA_DMA_I2C0_SDA	0xc600004c
+			>;
+		};
+
+		pinctrl_lpi2c1: lpi2c1grp {
+			fsl,pins = <
+				SC_P_GPT0_CLK_DMA_I2C1_SCL		0xc600004c
+				SC_P_GPT0_CAPTURE_DMA_I2C1_SDA		0xc600004c
+			>;
+		};
+
+		pinctrl_lpuart0: lpuart0grp {
+			fsl,pins = <
+				SC_P_UART0_RX_DMA_UART0_RX		0x06000020
+				SC_P_UART0_TX_DMA_UART0_TX		0x06000020
+			>;
+		};
+
+		pinctrl_lpuart1: lpuart1grp {
+			fsl,pins = <
+				SC_P_UART1_RX_DMA_UART1_RX		0x06000020
+				SC_P_UART1_TX_DMA_UART1_TX		0x06000020
+				SC_P_UART1_CTS_B_DMA_UART1_CTS_B	0x06000020
+				SC_P_UART1_RTS_B_DMA_UART1_RTS_B	0x06000020
+			>;
+		};
+
+		pinctrl_lpuart3: lpuart3grp {
+			fsl,pins = <
+				SC_P_M41_GPIO0_00_DMA_UART3_RX		0x06000020
+				SC_P_M41_GPIO0_01_DMA_UART3_TX		0x06000020
+			>;
+		};
+
+		pinctrl_mlb: mlbgrp {
+			fsl,pins = <
+				SC_P_MLB_SIG_CONN_MLB_SIG		0x21
+				SC_P_MLB_CLK_CONN_MLB_CLK		0x21
+				SC_P_MLB_DATA_CONN_MLB_DATA		0x21
+			>;
+		};
+
+		pinctrl_isl29023: isl29023grp {
+			fsl,pins = <
+				SC_P_ADC_IN2_LSIO_GPIO3_IO20		0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+			fsl,pins = <
+				SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21	0x00000021
+				SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22	0x00000021
+				SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_gpio: usdhc3grpgpio {
+			fsl,pins = <
+				SC_P_USDHC2_RESET_B_LSIO_GPIO4_IO09	0x00000021
+				SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000041
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000021
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000021
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000021
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000021
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000021
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+	};
+};
+
+&lpuart0 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lpuart1 { /* Q7 connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+&pd_dma_lpuart0 {
+	debug_console;
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	fsl,tuning-start-tap = <20>;
+	fsl,tuning-step= <2>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc3_vmmc>;
+	fsl,tuning-start-tap = <20>;
+	fsl,tuning-step= <2>;
+	status = "okay";
+};
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index 4e76612d05..71221d8d06 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -86,6 +86,12 @@ config TARGET_IMX8QM_MEK
 	select BOARD_LATE_INIT
 	select IMX8QM
 
+config TARGET_CONGA_QMX8
+	bool "Support congatec conga-QMX8 board"
+	select BOARD_LATE_INIT
+	select SUPPORT_SPL
+	select IMX8QM
+
 config TARGET_IMX8QM_ROM7720_A1
 	bool "Support i.MX8QM ROM-7720-A1"
 	select BOARD_LATE_INIT
@@ -101,6 +107,7 @@ endchoice
 
 source "board/freescale/imx8qm_mek/Kconfig"
 source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/congatec/cgtqmx8/Kconfig"
 source "board/advantech/imx8qm_rom7720_a1/Kconfig"
 source "board/toradex/apalis-imx8/Kconfig"
 source "board/toradex/colibri-imx8x/Kconfig"
diff --git a/board/congatec/cgtqmx8/Kconfig b/board/congatec/cgtqmx8/Kconfig
new file mode 100644
index 0000000000..7273039261
--- /dev/null
+++ b/board/congatec/cgtqmx8/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_CONGA_QMX8
+
+config SYS_BOARD
+	default "cgtqmx8"
+
+config SYS_VENDOR
+	default "congatec"
+
+config SYS_CONFIG_NAME
+	default "cgtqmx8"
+
+source "board/congatec/common/Kconfig"
+
+endif
diff --git a/board/congatec/cgtqmx8/MAINTAINERS b/board/congatec/cgtqmx8/MAINTAINERS
new file mode 100644
index 0000000000..53bc0f93b7
--- /dev/null
+++ b/board/congatec/cgtqmx8/MAINTAINERS
@@ -0,0 +1,7 @@
+i.MX8QM CGTQMX8 BOARD
+M:	Oliver Graute <oliver.graute@kococonnector.com>
+S:	Maintained
+F:	board/congatec/cgtqmx8/
+F:	arch/arm/dts/imx8qm-cgtqmx8.dts
+F:	include/configs/cgtqmx8.h
+F:	configs/cgtqmx8_defconfig
diff --git a/board/congatec/cgtqmx8/Makefile b/board/congatec/cgtqmx8/Makefile
new file mode 100644
index 0000000000..4b59dbb6bc
--- /dev/null
+++ b/board/congatec/cgtqmx8/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += cgtqmx8.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
diff --git a/board/congatec/cgtqmx8/cgtqmx8.c b/board/congatec/cgtqmx8/cgtqmx8.c
new file mode 100644
index 0000000000..fb0cf09138
--- /dev/null
+++ b/board/congatec/cgtqmx8/cgtqmx8.c
@@ -0,0 +1,460 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 congatec AG
+ * Copyright (C) 2019 Oliver Graute <oliver.graute@kococonnector.com>
+ */
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <fsl_esdhc.h>
+#include <init.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <usb.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/delay.h>
+#include <power-domain.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ESDHC_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ESDHC_CLK_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_INPUT_PAD_CTRL	((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_NORMAL_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define FSPI_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define GPIO_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define I2C_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define UART_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+	SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+void board_late_mmc_env_init(void);
+void init_clk_usdhc(u32 index);
+int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg);
+
+static void setup_iomux_uart(void)
+{
+	imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+	/* sc_ipc_t ipcHndl = 0; */
+	sc_err_t scierr = 0;
+
+	/* When start u-boot in XEN VM, directly return */
+	/* if (IS_ENABLED(CONFIG_XEN)) */
+		/* return 0; */
+
+	/* ipcHndl = gd->arch.ipc_channel_handle; */
+
+	/* Power up UART0, this is very early while power domain is not working */
+	scierr = sc_pm_set_resource_power_mode(-1, SC_R_UART_0, SC_PM_PW_MODE_ON);
+	if (scierr != SC_ERR_NONE)
+		return 0;
+
+	/* Set UART0 clock root to 80 MHz */
+	sc_pm_clock_rate_t rate = 80000000;
+
+	scierr = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate);
+	if (scierr != SC_ERR_NONE)
+		return 0;
+
+	/* Enable UART0 clock root */
+	scierr = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false);
+	if (scierr != SC_ERR_NONE)
+		return 0;
+
+	setup_iomux_uart();
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_FSL_ESDHC_IMX)
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(5, 22)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(4, 12)
+
+static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
+	{USDHC1_BASE_ADDR, 0, 8},
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR, 0, 4},
+};
+
+static iomux_cfg_t emmc0[] = {
+	SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc1_sd[] = {
+	SC_P_USDHC1_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_USDHC1_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA6 | MUX_MODE_ALT(2) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA7 | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc2_sd[] = {
+	SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_WP | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+int board_mmc_init(struct bd_info *bis)
+{
+	int i, ret;
+	struct power_domain pd;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0 (onboard eMMC)     USDHC1
+	 * mmc1 (external SD card) USDHC2
+	 * mmc2 (onboard µSD)      USDHC3
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+		  /* onboard eMMC */
+			if (!imx8_power_domain_lookup_name("conn_sdhc0", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0));
+			init_clk_usdhc(0);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+		  /* external SD card */
+			if (!imx8_power_domain_lookup_name("conn_sdhc1", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(usdhc1_sd, ARRAY_SIZE(usdhc1_sd));
+			init_clk_usdhc(1);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			gpio_request(USDHC1_CD_GPIO, "sd1_cd");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			break;
+		case 2:
+		  /* onboard µSD */
+			if (!imx8_power_domain_lookup_name("conn_sdhc2", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd));
+			init_clk_usdhc(2);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			gpio_request(USDHC2_CD_GPIO, "sd2_cd");
+			gpio_direction_input(USDHC2_CD_GPIO);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+		}
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+#endif /* CONFIG_FSL_ESDHC_IMX */
+
+#if (IS_ENABLED(CONFIG_FEC_MXC))
+
+#include <miiphy.h>
+
+static iomux_cfg_t pad_enet0[] = {
+	SC_P_ENET0_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD0 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD1 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD2 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD3 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXC | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD0 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD1 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD2 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD3 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_MDC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_MDIO | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx8_iomux_setup_multiple_pads(pad_enet0, ARRAY_SIZE(pad_enet0));
+}
+
+static void enet_device_phy_reset(void)
+{
+	gpio_set_value(FEC0_RESET, 0);
+	udelay(50);
+	gpio_set_value(FEC0_RESET, 1);
+
+	/* The board has a long delay for this reset to become stable */
+	mdelay(200);
+}
+
+int board_eth_init(struct bd_info *bis)
+{
+	setup_iomux_fec();
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+static int setup_fec(void)
+{
+	/* Reset ENET PHY */
+	enet_device_phy_reset();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_GPIO
+
+#define LVDS_ENABLE IMX_GPIO_NR(1, 6)
+#define BKL_ENABLE  IMX_GPIO_NR(1, 7)
+
+static iomux_cfg_t board_gpios[] = {
+	SC_P_LVDS0_I2C0_SCL | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+	SC_P_LVDS0_I2C0_SDA | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+	SC_P_ESAI1_FST | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+};
+
+static void board_gpio_init(void)
+{
+	imx8_iomux_setup_multiple_pads(board_gpios, ARRAY_SIZE(board_gpios));
+
+	/* enable LVDS */
+	gpio_request(LVDS_ENABLE, "lvds_enable");
+	gpio_direction_output(LVDS_ENABLE, 1);
+
+	/* enable backlight */
+	gpio_request(BKL_ENABLE, "bkl_enable");
+	gpio_direction_output(BKL_ENABLE, 1);
+
+	/* ethernet reset */
+	gpio_request(FEC0_RESET, "enet0_reset");
+	gpio_direction_output(FEC0_RESET, 1);
+}
+#endif
+
+int checkboard(void)
+{
+	puts("Board: conga-QMX8\n");
+
+	build_info();
+	print_bootinfo();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+#ifdef CONFIG_MXC_GPIO
+	board_gpio_init();
+#endif
+
+#if (IS_ENABLED(CONFIG_FEC_MXC))
+	setup_fec();
+#endif
+
+	return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+	/* TODO */
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	return 0;
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return devno;
+}
+
+int mmc_map_to_kernel_blk(int dev_no)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return dev_no;
+}
+
+extern u32 _end_ofs;
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "QMX8");
+	env_set("board_rev", "iMX8QM");
+#endif
+
+	env_set("sec_boot", "no");
+#ifdef CONFIG_AHAB_BOOT
+	env_set("sec_boot", "yes");
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+#ifdef IMX_LOAD_HDMI_FIMRWARE
+	char *end_of_uboot;
+	char command[256];
+
+	end_of_uboot = (char *)(ulong)(CONFIG_SYS_TEXT_BASE + _end_ofs
+			+ fdt_totalsize(gd->fdt_blob));
+	end_of_uboot += 9;
+
+	/* load hdmitxfw.bin and hdmirxfw.bin*/
+	memcpy(IMX_HDMI_FIRMWARE_LOAD_ADDR, end_of_uboot,
+	       IMX_HDMITX_FIRMWARE_SIZE + IMX_HDMIRX_FIRMWARE_SIZE);
+
+	sprintf(command, "hdp load 0x%x", IMX_HDMI_FIRMWARE_LOAD_ADDR);
+	run_command(command, 0);
+
+	sprintf(command, "hdprx load 0x%x",
+		IMX_HDMI_FIRMWARE_LOAD_ADDR + IMX_HDMITX_FIRMWARE_SIZE);
+	run_command(command, 0);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_FSL_FASTBOOT
+#ifdef CONFIG_ANDROID_RECOVERY
+int is_recovery_key_pressing(void)
+{
+	return 0; /*TODO*/
+}
+#endif /*CONFIG_ANDROID_RECOVERY*/
+#endif /*CONFIG_FSL_FASTBOOT*/
+
+/* Only Enable USB3 resources currently */
+int board_usb_init(int index, enum usb_init_type init)
+{
+	return 0;
+}
diff --git a/board/congatec/cgtqmx8/imximage.cfg b/board/congatec/cgtqmx8/imximage.cfg
new file mode 100644
index 0000000000..e324c7ca37
--- /dev/null
+++ b/board/congatec/cgtqmx8/imximage.cfg
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier:	GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
diff --git a/board/congatec/cgtqmx8/spl.c b/board/congatec/cgtqmx8/spl.c
new file mode 100644
index 0000000000..2a5d4c1bcd
--- /dev/null
+++ b/board/congatec/cgtqmx8/spl.c
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <init.h>
+#include <log.h>
+#include <spl.h>
+#include <dm/uclass.h>
+#include <dm/device.h>
+#include <dm/uclass-internal.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void spl_board_init(void)
+{
+	struct udevice *dev;
+	int offset;
+
+	uclass_find_first_device(UCLASS_MISC, &dev);
+
+	for (; dev; uclass_find_next_device(&dev)) {
+		if (device_probe(dev))
+			continue;
+	}
+
+	offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1, "nxp,imx8-pd");
+	while (offset != -FDT_ERR_NOTFOUND) {
+		lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset),
+			       NULL, true);
+		offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset,
+						       "nxp,imx8-pd");
+	}
+
+	uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev);
+
+	for (; dev; uclass_find_next_device(&dev)) {
+		if (device_probe(dev))
+			continue;
+	}
+
+	arch_cpu_init();
+
+	board_early_init_f();
+
+	timer_init();
+
+	preloader_console_init();
+
+	puts("Normal Boot\n");
+}
+
+#if (IS_ENABLED(CONFIG_SPL_LOAD_FIT))
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+	/* Clear global data */
+	memset((void *)gd, 0, sizeof(gd_t));
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	board_init_r(NULL, 0);
+}
diff --git a/board/congatec/common/Kconfig b/board/congatec/common/Kconfig
new file mode 100644
index 0000000000..5c205bd830
--- /dev/null
+++ b/board/congatec/common/Kconfig
@@ -0,0 +1,48 @@
+if !ARCH_IMX8M && !ARCH_IMX8
+
+config CHAIN_OF_TRUST
+	depends on !FIT_SIGNATURE && SECURE_BOOT
+	imply CMD_BLOB
+	imply CMD_HASH if ARM
+	select FSL_CAAM
+	select SPL_BOARD_INIT if (ARM && SPL)
+	select SHA_HW_ACCEL
+	select SHA_PROG_HW_ACCEL
+	select ENV_IS_NOWHERE
+	select CMD_EXT4 if ARM
+	select CMD_EXT4_WRITE if ARM
+	bool
+	default y
+
+config CMD_ESBC_VALIDATE
+	bool "Enable the 'esbc_validate' and 'esbc_halt' commands"
+	default y if CHAIN_OF_TRUST
+	help
+	  This option enables two commands used for secure booting:
+
+	    esbc_validate - validate signature using RSA verification
+	    esbc_halt - put the core in spin loop (Secure Boot Only)
+
+endif
+
+config VOL_MONITOR_LTC3882_READ
+	depends on VID
+	bool "Enable the LTC3882 voltage monitor read"
+	default n
+	help
+	 This option enables LTC3882 voltage monitor read
+	 functionality. It is used by common VID driver.
+
+config VOL_MONITOR_LTC3882_SET
+	depends on VID
+	bool "Enable the LTC3882 voltage monitor set"
+	default n
+	help
+	 This option enables LTC3882 voltage monitor set
+	 functionality. It is used by common VID driver.
+
+config USB_TCPC
+	bool "USB Typec port controller simple driver"
+	default n
+	help
+	  Enable USB type-c port controller (TCPC) driver
diff --git a/board/congatec/common/Makefile b/board/congatec/common/Makefile
new file mode 100644
index 0000000000..d4ddfbf971
--- /dev/null
+++ b/board/congatec/common/Makefile
@@ -0,0 +1,23 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+# necessary to create built-in.o
+obj- := __dummy__.o
+else
+
+obj-y				+= mmc.o
+
+endif
diff --git a/board/congatec/common/mmc.c b/board/congatec/common/mmc.c
new file mode 100644
index 0000000000..bb7a3d4a9a
--- /dev/null
+++ b/board/congatec/common/mmc.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2018 NXP
+ *
+ */
+#include <common.h>
+#include <linux/errno.h>
+#include <asm/io.h>
+#include <env.h>
+#include <command.h>
+#include <stdbool.h>
+#include <mmc.h>
+
+static int check_mmc_autodetect(void)
+{
+	char *autodetect_str = env_get("mmcautodetect");
+
+	if ((autodetect_str) && (strcmp(autodetect_str, "yes") == 0))
+		return 1;
+
+	return 0;
+}
+
+/* This should be defined for each board */
+__weak int mmc_map_to_kernel_blk(int dev_no)
+{
+	return dev_no;
+}
+
+void board_late_mmc_env_init(void)
+{
+	char cmd[32];
+	char mmcblk[32];
+	u32 dev_no = mmc_get_env_dev();
+
+	if (!check_mmc_autodetect())
+		return;
+
+	env_set_ulong("mmcdev", dev_no);
+
+	/* Set mmcblk env */
+	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
+		mmc_map_to_kernel_blk(dev_no));
+	env_set("mmcroot", mmcblk);
+
+	sprintf(cmd, "mmc dev %d", dev_no);
+	run_command(cmd, 0);
+}
diff --git a/configs/cgtqmx8_defconfig b/configs/cgtqmx8_defconfig
new file mode 100644
index 0000000000..238e421601
--- /dev/null
+++ b/configs/cgtqmx8_defconfig
@@ -0,0 +1,86 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_CONGA_QMX8=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=3
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/congatec/cgtqmx8/imximage.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_IMX_BOOTAUX=y
+CONFIG_LOG=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_CPU=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FUSE=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8qm-cgtqmx8"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_SPL_DM=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_MXC_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPL_TINY_MEMSET=y
+# CONFIG_EFI_LOADER is not set
+CONFIG_SYS_MMCSD_FS_BOOT_PARTITION=0
+CONFIG_SYS_MMC_ENV_PART=0
+CONFIG_SYS_MMC_ENV_DEV=1
diff --git a/doc/board/congatec/cgtqmx8.rst b/doc/board/congatec/cgtqmx8.rst
new file mode 100644
index 0000000000..bccdef2f16
--- /dev/null
+++ b/doc/board/congatec/cgtqmx8.rst
@@ -0,0 +1,70 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for the Congatec conga-QMX8 board
+========================================
+
+Quick Start
+-----------
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Get imx-mkimage
+- Build U-Boot
+- Build imx-mkimage
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted firmware
+--------------------------------------
+
+.. code-block:: bash
+
+     $ git clone https://source.codeaurora.org/external/imx/imx-atf
+     $ cd imx-atf/
+     $ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
+     $ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+---------------------------------------
+
+.. code-block:: bash
+
+     $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
+     $ chmod +x imx-sc-firmware-1.1.bin
+     $ ./imx-sc-firmware-1.1.bin
+     $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+     $ chmod +x firmware-imx-8.0.bin
+     $ ./firmware-imx-8.0.bin
+
+Or use this to avoid running random scripts from the internet,
+but note that you must agree to the license the script displays:
+
+.. code-block:: bash
+
+     $ dd if=imx-sc-firmware-1.1.bin of=imx-sc-firmware-1.1.tar.bz2 bs=37185 skip=1
+     $ tar -xf imx-sc-firmware-1.1.tar.bz2
+     $ cp imx-sc-firmware-1.1/mx8qx-val-scfw-tcm.bin $(builddir)
+
+     $ dd if=firmware-imx-8.0.bin of=firmware-imx-8.0.tar.bz2 bs=37180 skip=1
+     $ tar -xf firmware-imx-8.0.tar.bz2
+     $ cp firmware-imx-8.0/firmware/seco/mx8qm-ahab-container.img $(builddir)
+
+Build U-Boot
+------------
+
+.. code-block:: bash
+
+     $ export ATF_LOAD_ADDR=0x80000000
+     $ export BL33_LOAD_ADDR=0x80020000
+     $ make cgtqmx8_defconfig
+     $ make u-boot.bin
+     $ make flash.bin
+
+Flash the binary into the SD card
+---------------------------------
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+.. code-block:: bash
+
+     $ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync
diff --git a/doc/board/congatec/index.rst b/doc/board/congatec/index.rst
new file mode 100644
index 0000000000..cc57b36b2e
--- /dev/null
+++ b/doc/board/congatec/index.rst
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Congatec
+========
+
+.. toctree::
+   :maxdepth: 2
+
+   cgtqmx8.rst
diff --git a/doc/board/index.rst b/doc/board/index.rst
index a70d2de19d..747511f7dd 100644
--- a/doc/board/index.rst
+++ b/doc/board/index.rst
@@ -11,6 +11,7 @@ Board-specific doc
    AndesTech/index
    amlogic/index
    atmel/index
+   congatec/index
    coreboot/index
    emulation/index
    freescale/index
diff --git a/include/configs/cgtqmx8.h b/include/configs/cgtqmx8.h
new file mode 100644
index 0000000000..15c50279ad
--- /dev/null
+++ b/include/configs/cgtqmx8.h
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ * Copyright 2018 congatec AG
+ *
+ */
+
+#ifndef __CGTQMX8_H
+#define __CGTQMX8_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_TEXT_BASE				0x0
+#define CONFIG_SPL_MAX_SIZE				(124 * 1024)
+#define CONFIG_SYS_MONITOR_LEN				(1024 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR		0x800
+
+#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK		0x013E000
+#define CONFIG_SPL_BSS_START_ADDR	0x00128000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x1000	/* 4 KB */
+#define CONFIG_SYS_SPL_MALLOC_START	0x00120000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x3000	/* 12 KB */
+#define CONFIG_SERIAL_LPUART_BASE	0x5a060000
+#define CONFIG_MALLOC_F_ADDR		0x00120000
+
+#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
+
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
+
+#define CONFIG_OF_EMBED
+#endif
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+#define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define USDHC1_BASE_ADDR		0x5B010000
+#define USDHC2_BASE_ADDR		0x5B020000
+#define USDHC3_BASE_ADDR		0x5B030000
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+/* Boot M4 */
+#define M4_BOOT_ENV \
+	"m4_0_image=m4_0.bin\0" \
+	"m4_1_image=m4_1.bin\0" \
+	"loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \
+	"loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \
+	"m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \
+	"m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \
+
+#ifdef CONFIG_NAND_BOOT
+#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
+#else
+#define MFG_NAND_PARTITION ""
+#endif
+#define FEC0_RESET IMX_GPIO_NR(2, 5)
+#define FEC0_PDOMAIN "conn_enet0"
+
+#define CONFIG_MFG_ENV_SETTINGS \
+	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+		"rdinit=/linuxrc " \
+		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+		"g_mass_storage.iSerialNumber=\"\" "\
+		MFG_NAND_PARTITION \
+		"clk_ignore_unused "\
+		"\0" \
+	"initrd_addr=0x83800000\0" \
+	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	CONFIG_MFG_ENV_SETTINGS \
+	M4_BOOT_ENV \
+	"script=boot.scr\0" \
+	"image=Image\0" \
+	"panel=NULL\0" \
+	"console=ttyLP0\0" \
+	"fdt_addr=0x83000000\0"			\
+	"boot_fdt=try\0" \
+	"fdt_file=imx8qm-cgt-qmx8.dtb\0" \
+	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} earlycon\0 " \
+	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"echo wait for boot; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp rw earlycon\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs;  " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${loadaddr} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"booti; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR			0x80280000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_SP_ADDR		0x80200000
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+#define PHYS_SDRAM_1			0x80000000
+#define PHYS_SDRAM_2			0x880000000
+#define PHYS_SDRAM_1_SIZE		0x80000000	/* 2 GB */
+#define PHYS_SDRAM_2_SIZE		0x100000000	/* 4 GB */
+
+/* Serial */
+#define CONFIG_BAUDRATE			115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY		8000000	/* 8MHz */
+
+/* Networking */
+#define CONFIG_FEC_MXC_PHYADDR		-1
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define FEC_QUIRK_ENET_MAC
+
+#endif /* __CGTQMX8_H */
-- 
2.17.1


^ permalink raw reply related	[flat|nested] 2+ messages in thread