Re: [PATCH 2/2] ARM: dts: owl-s500-roseapplepi: Add ethernet support

[Manivannan Sadhasivam <mani@kernel.org>]

On Fri, Jun 11, 2021 at 12:09:22AM +0300, Cristian Ciocaltea wrote:
> Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
> SBC. Additionally, provide the necessary properties for the generic S500
> ethernet node in order to setup PHY and MDIO.
> 
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
> ---
>  arch/arm/boot/dts/owl-s500-roseapplepi.dts | 56 ++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> index b8c5db2344aa..bffabc7eaa50 100644
> --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> @@ -225,6 +225,38 @@ bias1-pinconf {
>  			bias-pull-down;
>  		};
>  	};
> +
> +	ethernet_pins: ethernet-pins {
> +		txd01-pinmux {
> +			groups = "rmii_txd0_mfp", "rmii_txd1_mfp";
> +			function = "eth_rmii";
> +		};
> +
> +		rxd01-pinmux {
> +			groups = "rmii_rxd0_mfp", "rmii_rxd1_mfp";
> +			function = "eth_rmii";
> +		};
> +
> +		txen_rxer-pinmux {
> +			groups = "rmii_txen_mfp", "rmii_rxen_mfp";
> +			function = "eth_rmii";
> +		};
> +
> +		crs_dv_ref_clk-pinmux {
> +			groups = "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
> +			function = "eth_rmii";

Since the function is same, just club all the groups together.

> +		};
> +
> +		ref_clk-pinconf {
> +			groups = "rmii_ref_clk_drv";
> +			drive-strength = <2>;
> +		};
> +
> +		phy_clk-pinmux {
> +			groups = "clko_25m_mfp";
> +			function = "clko_25m";
> +		};

Move this above node pinconf.

> +	};
>  };
>  
>  /* uSD */
> @@ -241,6 +273,30 @@ &mmc0 {
>  	vqmmc-supply = <&sd_vcc>;
>  };
>  
> +&ethernet {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ethernet_pins>;
> +	phy-mode = "rmii";
> +	phy-handle = <&eth_phy>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
> +		reset-delay-us = <10000>;
> +		reset-post-delay-us = <150000>;

reset-* properties belong to "ethernet-phy" node. Also, while adding new nodes
please run the dtbs_check and try to address the warnings.

Thanks,
Mani

> +
> +		eth_phy: ethernet-phy@3 {
> +			reg = <0x3>;
> +			max-speed = <100>;
> +			interrupt-parent = <&sirq>;
> +			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +		};
> +	};
> +};
> +
>  &twd_timer {
>  	status = "okay";
>  };
> -- 
> 2.32.0
>