* [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
@ 2021-06-22 1:50 ainux.wang
2021-06-22 3:15 ` Guenter Roeck
2021-06-22 6:27 ` teng sterling
0 siblings, 2 replies; 7+ messages in thread
From: ainux.wang @ 2021-06-22 1:50 UTC (permalink / raw)
To: jdelvare, linux, corbet, ainux.wang
Cc: linux-hwmon, linux-doc, sterlingteng, chenhuacai, chenhuacai
From: "Ainux.Wang" <ainux.wang@gmail.com>
Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
This is a triple-loop, digital, multi-phase controller.
This device:
- Supports up to three power rail.
- Provides 6 pulse-width modulations (PWMs), and can be configured up
to 6-phase operation for Rail A , up to 2-phase operation for Rail B
and up to 1-phase operation for Rail C.
- The PMBus registers are distributed into three pages: Page 0, Page 1,
Page 2. Page 0 contains the registers for Rail A and most of the common
settings for all of the rails. Page 1 contains register information for
Rail B. Page 2 contains register information for Rail C.
- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
IMVP9.
Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
v3:
- Added change log here.
- Errors in the document have been modified.
- Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
- Removed unnecessary vout_params and empty line.
v2:
- Reference has been added to Documentation/hwmon/index.rst.
- Droped 'vendor'.
- Removed change codes of the PMBus core and added mp2949a_identify()
and mp2949a_read_byte_data() to this driver.
v1:
- Add support for MPS MP2949A.
---
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
drivers/hwmon/pmbus/Kconfig | 9 +++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/mp2949a.c | 118 ++++++++++++++++++++++++++++++++
5 files changed, 173 insertions(+)
create mode 100644 Documentation/hwmon/mp2949a.rst
create mode 100644 drivers/hwmon/pmbus/mp2949a.c
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 9ed60fa84cbe..56aac3b1678d 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
mcp3021
menf21bmc
mlxreg-fan
+ mp2949a
mp2975
nct6683
nct6775
diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
new file mode 100644
index 000000000000..0235dec70f63
--- /dev/null
+++ b/Documentation/hwmon/mp2949a.rst
@@ -0,0 +1,44 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2949a
+====================
+
+Supported chips:
+
+ * MPS MP2949A
+
+ Prefix: 'mp2949a'
+
+Author:
+
+ Ainux Wang <ainux.wang@gmail.com>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+triple-loop, digital, multi-phase controller MP2949A.
+
+This device:
+
+- Supports up to three power rail.
+- Provides 6 pulse-width modulations (PWMs), and can be configured for
+ to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
+ and up to 1-phase operation for Rail C.
+- The PMBus registers are distributed into three pages: Page 0, Page 1,
+ Page 2. Page 0 contains the registers for Rail A and most of the common
+ settings for all of the rails. Page 1 contains register information for
+ Rail B. Page 2 contains register information for Rail C.
+- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
+ IMVP9.
+
+Device supports:
+
+- SVID interface.
+- PMBus rev 1.2 interface.
+
+Device supports direct format for reading output power.
+Device supports linear format for reading input voltage, output current,
+and temperature.
+Device supports VID for reading output voltage.
+The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 37a5c39784fa..b1344b265976 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -248,6 +248,15 @@ config SENSORS_MAX8688
This driver can also be built as a module. If so, the module will
be called max8688.
+config SENSORS_MP2949A
+ tristate "MPS MP2949A"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP2949A Triple Loop Digital Multi-Phase Controller.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp2949a.
+
config SENSORS_MP2975
tristate "MPS MP2975"
help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index f8dcc27cd56a..bfb55ab12da1 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
+obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
new file mode 100644
index 000000000000..744c88b8ebca
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2949a.c
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for Monolithic Power Systems MP2949A
+ *
+ * Copyright (c) 2021 Lemote Technologies. All rights reserved.
+ * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+#define MP2949A_PAGE_NUM 3
+
+#define MP2949A_MFR_VR_CONFIG 0xE4
+
+static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+ switch (reg) {
+ case PMBUS_VOUT_MODE:
+ /*
+ * This chip do not support the VOUT_MODE command.
+ * There is not VOUT_MODE command in MP2949A datasheet P29~P31.
+ * So there is a EINVAL in here.
+ */
+ return -EINVAL;
+ default:
+ return -ENODATA;
+ }
+}
+
+static int mp2949a_identify(struct i2c_client *client,
+ struct pmbus_driver_info *info)
+{
+ int i, ret;
+
+ for (i = 0; i < MP2949A_PAGE_NUM; i++) {
+ ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Rail A bit 5, Rail B bit 4, Rail C bit 3.
+ * 1'b1: 5mV (vr12/imvp8)
+ * 1'b0: 10mv (imvp9)
+ */
+ info->vrm_version[i] = (ret & ~BIT(5-i)) ? vr12 : imvp9;
+ }
+
+ return 0;
+}
+
+static struct pmbus_driver_info mp2949a_info = {
+ .pages = MP2949A_PAGE_NUM,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = vid,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_POWER] = direct,
+ .m[PSC_POWER] = 1,
+ .b[PSC_POWER] = 0,
+ .R[PSC_POWER] = 0,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
+ .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_POUT,
+ .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_POUT,
+ .identify = mp2949a_identify,
+ .read_byte_data = mp2949a_read_byte_data,
+};
+
+static int mp2949a_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct pmbus_driver_info *info;
+
+ info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
+ GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2949a_id[] = {
+ {"mp2949a", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2949a_id);
+
+static const struct of_device_id mp2949a_of_match[] = {
+ {.compatible = "mps,mp2949a"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, mp2949a_of_match);
+
+static struct i2c_driver mp2949a_driver = {
+ .driver = {
+ .name = "mp2949a",
+ .of_match_table = of_match_ptr(mp2949a_of_match),
+ },
+ .probe = mp2949a_probe,
+ .id_table = mp2949a_id,
+};
+
+module_i2c_driver(mp2949a_driver);
+
+MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
+MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
+MODULE_LICENSE("GPL");
--
2.18.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
2021-06-22 1:50 [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A ainux.wang
@ 2021-06-22 3:15 ` Guenter Roeck
2021-06-22 6:51 ` Ainux Wang
2021-06-22 6:27 ` teng sterling
1 sibling, 1 reply; 7+ messages in thread
From: Guenter Roeck @ 2021-06-22 3:15 UTC (permalink / raw)
To: ainux.wang
Cc: jdelvare, corbet, linux-hwmon, linux-doc, sterlingteng,
chenhuacai, chenhuacai
On Tue, Jun 22, 2021 at 09:50:11AM +0800, ainux.wang@gmail.com wrote:
> From: "Ainux.Wang" <ainux.wang@gmail.com>
>
> Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> This is a triple-loop, digital, multi-phase controller.
> This device:
> - Supports up to three power rail.
> - Provides 6 pulse-width modulations (PWMs), and can be configured up
> to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> and up to 1-phase operation for Rail C.
> - The PMBus registers are distributed into three pages: Page 0, Page 1,
> Page 2. Page 0 contains the registers for Rail A and most of the common
> settings for all of the rails. Page 1 contains register information for
> Rail B. Page 2 contains register information for Rail C.
> - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> IMVP9.
>
> Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
>
> v3:
> - Added change log here.
> - Errors in the document have been modified.
> - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> - Removed unnecessary vout_params and empty line.
>
> v2:
> - Reference has been added to Documentation/hwmon/index.rst.
> - Droped 'vendor'.
> - Removed change codes of the PMBus core and added mp2949a_identify()
> and mp2949a_read_byte_data() to this driver.
>
> v1:
> - Add support for MPS MP2949A.
> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/mp2949a.c | 118 ++++++++++++++++++++++++++++++++
> 5 files changed, 173 insertions(+)
> create mode 100644 Documentation/hwmon/mp2949a.rst
> create mode 100644 drivers/hwmon/pmbus/mp2949a.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 9ed60fa84cbe..56aac3b1678d 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> mcp3021
> menf21bmc
> mlxreg-fan
> + mp2949a
> mp2975
> nct6683
> nct6775
> diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> new file mode 100644
> index 000000000000..0235dec70f63
> --- /dev/null
> +++ b/Documentation/hwmon/mp2949a.rst
> @@ -0,0 +1,44 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2949a
> +====================
> +
> +Supported chips:
> +
> + * MPS MP2949A
> +
> + Prefix: 'mp2949a'
> +
> +Author:
> +
> + Ainux Wang <ainux.wang@gmail.com>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +triple-loop, digital, multi-phase controller MP2949A.
> +
> +This device:
> +
> +- Supports up to three power rail.
> +- Provides 6 pulse-width modulations (PWMs), and can be configured for
> + to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
> + and up to 1-phase operation for Rail C.
> +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> + Page 2. Page 0 contains the registers for Rail A and most of the common
> + settings for all of the rails. Page 1 contains register information for
> + Rail B. Page 2 contains register information for Rail C.
> +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> + IMVP9.
> +
> +Device supports:
> +
> +- SVID interface.
> +- PMBus rev 1.2 interface.
> +
> +Device supports direct format for reading output power.
> +Device supports linear format for reading input voltage, output current,
> +and temperature.
> +Device supports VID for reading output voltage.
> +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 37a5c39784fa..b1344b265976 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> This driver can also be built as a module. If so, the module will
> be called max8688.
>
> +config SENSORS_MP2949A
> + tristate "MPS MP2949A"
> + help
> + If you say yes here you get hardware monitoring support for MPS
> + MP2949A Triple Loop Digital Multi-Phase Controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called mp2949a.
> +
> config SENSORS_MP2975
> tristate "MPS MP2975"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index f8dcc27cd56a..bfb55ab12da1 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> new file mode 100644
> index 000000000000..744c88b8ebca
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2949a.c
> @@ -0,0 +1,118 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> + *
> + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +#define MP2949A_PAGE_NUM 3
> +
> +#define MP2949A_MFR_VR_CONFIG 0xE4
> +
> +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> +{
> + switch (reg) {
> + case PMBUS_VOUT_MODE:
> + /*
> + * This chip do not support the VOUT_MODE command.
> + * There is not VOUT_MODE command in MP2949A datasheet P29~P31.
> + * So there is a EINVAL in here.
> + */
> + return -EINVAL;
This is not a reason to add this code. The PMBus core handles this situation.
Please explain why this is needed. "The chip does not support this command"
is not a reason.
> + default:
> + return -ENODATA;
> + }
> +}
> +
> +static int mp2949a_identify(struct i2c_client *client,
> + struct pmbus_driver_info *info)
> +{
> + int i, ret;
> +
> + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> + ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> + * 1'b1: 5mV (vr12/imvp8)
> + * 1'b0: 10mv (imvp9)
> + */
> + info->vrm_version[i] = (ret & ~BIT(5-i)) ? vr12 : imvp9;
Space before and after '-'.
Also, why ~ ? This evaluates all bits except the target bit.
> + }
> +
> + return 0;
> +}
> +
> +static struct pmbus_driver_info mp2949a_info = {
> + .pages = MP2949A_PAGE_NUM,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = vid,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .format[PSC_POWER] = direct,
> + .m[PSC_POWER] = 1,
> + .b[PSC_POWER] = 0,
> + .R[PSC_POWER] = 0,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .identify = mp2949a_identify,
> + .read_byte_data = mp2949a_read_byte_data,
> +};
> +
> +static int mp2949a_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct pmbus_driver_info *info;
> +
> + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> + GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2949a_id[] = {
> + {"mp2949a", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> +
> +static const struct of_device_id mp2949a_of_match[] = {
> + {.compatible = "mps,mp2949a"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> +
> +static struct i2c_driver mp2949a_driver = {
> + .driver = {
> + .name = "mp2949a",
> + .of_match_table = of_match_ptr(mp2949a_of_match),
> + },
> + .probe = mp2949a_probe,
> + .id_table = mp2949a_id,
> +};
> +
> +module_i2c_driver(mp2949a_driver);
> +
> +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
2021-06-22 1:50 [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A ainux.wang
2021-06-22 3:15 ` Guenter Roeck
@ 2021-06-22 6:27 ` teng sterling
2021-06-22 6:52 ` Ainux Wang
1 sibling, 1 reply; 7+ messages in thread
From: teng sterling @ 2021-06-22 6:27 UTC (permalink / raw)
To: David Ainux
Cc: jdelvare, linux, Jonathan Corbet, linux-hwmon, linux-doc,
Huacai Chen, Huacai Chen
<ainux.wang@gmail.com> 于2021年6月22日周二 上午9:50写道：
>
> From: "Ainux.Wang" <ainux.wang@gmail.com>
>
> Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> This is a triple-loop, digital, multi-phase controller.
> This device:
> - Supports up to three power rail.
> - Provides 6 pulse-width modulations (PWMs), and can be configured up
> to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> and up to 1-phase operation for Rail C.
> - The PMBus registers are distributed into three pages: Page 0, Page 1,
> Page 2. Page 0 contains the registers for Rail A and most of the common
> settings for all of the rails. Page 1 contains register information for
> Rail B. Page 2 contains register information for Rail C.
> - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> IMVP9.
>
> Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
>
> v3:
> - Added change log here.
> - Errors in the document have been modified.
> - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> - Removed unnecessary vout_params and empty line.
>
> v2:
> - Reference has been added to Documentation/hwmon/index.rst.
> - Droped 'vendor'.
> - Removed change codes of the PMBus core and added mp2949a_identify()
> and mp2949a_read_byte_data() to this driver.
>
> v1:
> - Add support for MPS MP2949A.
> ---
Hi，Ainux
Change log goes here. just like:
...
Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
---
v3:
- Added change log here.
- Errors in the document have been modified.
- Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
- Removed unnecessary vout_params and empty line.
v2:
- Reference has been added to Documentation/hwmon/index.rst.
- Droped 'vendor'.
- Removed change codes of the PMBus core and added mp2949a_identify()
and mp2949a_read_byte_data() to this driver.
v1:
- Add support for MPS MP2949A.
Documentation/hwmon/index.rst | 1 +
...
Thanks,
Yanteng
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/mp2949a.c | 118 ++++++++++++++++++++++++++++++++
> 5 files changed, 173 insertions(+)
> create mode 100644 Documentation/hwmon/mp2949a.rst
> create mode 100644 drivers/hwmon/pmbus/mp2949a.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 9ed60fa84cbe..56aac3b1678d 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> mcp3021
> menf21bmc
> mlxreg-fan
> + mp2949a
> mp2975
> nct6683
> nct6775
> diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> new file mode 100644
> index 000000000000..0235dec70f63
> --- /dev/null
> +++ b/Documentation/hwmon/mp2949a.rst
> @@ -0,0 +1,44 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2949a
> +====================
> +
> +Supported chips:
> +
> + * MPS MP2949A
> +
> + Prefix: 'mp2949a'
> +
> +Author:
> +
> + Ainux Wang <ainux.wang@gmail.com>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +triple-loop, digital, multi-phase controller MP2949A.
> +
> +This device:
> +
> +- Supports up to three power rail.
> +- Provides 6 pulse-width modulations (PWMs), and can be configured for
> + to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
> + and up to 1-phase operation for Rail C.
> +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> + Page 2. Page 0 contains the registers for Rail A and most of the common
> + settings for all of the rails. Page 1 contains register information for
> + Rail B. Page 2 contains register information for Rail C.
> +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> + IMVP9.
> +
> +Device supports:
> +
> +- SVID interface.
> +- PMBus rev 1.2 interface.
> +
> +Device supports direct format for reading output power.
> +Device supports linear format for reading input voltage, output current,
> +and temperature.
> +Device supports VID for reading output voltage.
> +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 37a5c39784fa..b1344b265976 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> This driver can also be built as a module. If so, the module will
> be called max8688.
>
> +config SENSORS_MP2949A
> + tristate "MPS MP2949A"
> + help
> + If you say yes here you get hardware monitoring support for MPS
> + MP2949A Triple Loop Digital Multi-Phase Controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called mp2949a.
> +
> config SENSORS_MP2975
> tristate "MPS MP2975"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index f8dcc27cd56a..bfb55ab12da1 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> new file mode 100644
> index 000000000000..744c88b8ebca
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2949a.c
> @@ -0,0 +1,118 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> + *
> + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +#define MP2949A_PAGE_NUM 3
> +
> +#define MP2949A_MFR_VR_CONFIG 0xE4
> +
> +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> +{
> + switch (reg) {
> + case PMBUS_VOUT_MODE:
> + /*
> + * This chip do not support the VOUT_MODE command.
> + * There is not VOUT_MODE command in MP2949A datasheet P29~P31.
> + * So there is a EINVAL in here.
> + */
> + return -EINVAL;
> + default:
> + return -ENODATA;
> + }
> +}
> +
> +static int mp2949a_identify(struct i2c_client *client,
> + struct pmbus_driver_info *info)
> +{
> + int i, ret;
> +
> + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> + ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> + * 1'b1: 5mV (vr12/imvp8)
> + * 1'b0: 10mv (imvp9)
> + */
> + info->vrm_version[i] = (ret & ~BIT(5-i)) ? vr12 : imvp9;
> + }
> +
> + return 0;
> +}
> +
> +static struct pmbus_driver_info mp2949a_info = {
> + .pages = MP2949A_PAGE_NUM,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = vid,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .format[PSC_POWER] = direct,
> + .m[PSC_POWER] = 1,
> + .b[PSC_POWER] = 0,
> + .R[PSC_POWER] = 0,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .identify = mp2949a_identify,
> + .read_byte_data = mp2949a_read_byte_data,
> +};
> +
> +static int mp2949a_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct pmbus_driver_info *info;
> +
> + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> + GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2949a_id[] = {
> + {"mp2949a", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> +
> +static const struct of_device_id mp2949a_of_match[] = {
> + {.compatible = "mps,mp2949a"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> +
> +static struct i2c_driver mp2949a_driver = {
> + .driver = {
> + .name = "mp2949a",
> + .of_match_table = of_match_ptr(mp2949a_of_match),
> + },
> + .probe = mp2949a_probe,
> + .id_table = mp2949a_id,
> +};
> +
> +module_i2c_driver(mp2949a_driver);
> +
> +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
2021-06-22 3:15 ` Guenter Roeck
@ 2021-06-22 6:51 ` Ainux Wang
0 siblings, 0 replies; 7+ messages in thread
From: Ainux Wang @ 2021-06-22 6:51 UTC (permalink / raw)
To: Guenter Roeck
Cc: jdelvare, corbet, linux-hwmon, linux-doc, teng sterling,
chenhuacai, chenhuacai
Hi， Guenter
Thanks for the review. I'll address it all in v4.
Best regards,
Ainux Wang.
On Tue, 22 Jun 2021 at 11:15, Guenter Roeck <linux@roeck-us.net> wrote:
>
> On Tue, Jun 22, 2021 at 09:50:11AM +0800, ainux.wang@gmail.com wrote:
> > From: "Ainux.Wang" <ainux.wang@gmail.com>
> >
> > Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> > This is a triple-loop, digital, multi-phase controller.
> > This device:
> > - Supports up to three power rail.
> > - Provides 6 pulse-width modulations (PWMs), and can be configured up
> > to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> > and up to 1-phase operation for Rail C.
> > - The PMBus registers are distributed into three pages: Page 0, Page 1,
> > Page 2. Page 0 contains the registers for Rail A and most of the common
> > settings for all of the rails. Page 1 contains register information for
> > Rail B. Page 2 contains register information for Rail C.
> > - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > IMVP9.
> >
> > Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
> >
> > v3:
> > - Added change log here.
> > - Errors in the document have been modified.
> > - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> > - Removed unnecessary vout_params and empty line.
> >
> > v2:
> > - Reference has been added to Documentation/hwmon/index.rst.
> > - Droped 'vendor'.
> > - Removed change codes of the PMBus core and added mp2949a_identify()
> > and mp2949a_read_byte_data() to this driver.
> >
> > v1:
> > - Add support for MPS MP2949A.
> > ---
> > Documentation/hwmon/index.rst | 1 +
> > Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
> > drivers/hwmon/pmbus/Kconfig | 9 +++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/mp2949a.c | 118 ++++++++++++++++++++++++++++++++
> > 5 files changed, 173 insertions(+)
> > create mode 100644 Documentation/hwmon/mp2949a.rst
> > create mode 100644 drivers/hwmon/pmbus/mp2949a.c
> >
> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> > index 9ed60fa84cbe..56aac3b1678d 100644
> > --- a/Documentation/hwmon/index.rst
> > +++ b/Documentation/hwmon/index.rst
> > @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> > mcp3021
> > menf21bmc
> > mlxreg-fan
> > + mp2949a
> > mp2975
> > nct6683
> > nct6775
> > diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> > new file mode 100644
> > index 000000000000..0235dec70f63
> > --- /dev/null
> > +++ b/Documentation/hwmon/mp2949a.rst
> > @@ -0,0 +1,44 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +Kernel driver mp2949a
> > +====================
> > +
> > +Supported chips:
> > +
> > + * MPS MP2949A
> > +
> > + Prefix: 'mp2949a'
> > +
> > +Author:
> > +
> > + Ainux Wang <ainux.wang@gmail.com>
> > +
> > +Description
> > +-----------
> > +
> > +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> > +triple-loop, digital, multi-phase controller MP2949A.
> > +
> > +This device:
> > +
> > +- Supports up to three power rail.
> > +- Provides 6 pulse-width modulations (PWMs), and can be configured for
> > + to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
> > + and up to 1-phase operation for Rail C.
> > +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> > + Page 2. Page 0 contains the registers for Rail A and most of the common
> > + settings for all of the rails. Page 1 contains register information for
> > + Rail B. Page 2 contains register information for Rail C.
> > +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > + IMVP9.
> > +
> > +Device supports:
> > +
> > +- SVID interface.
> > +- PMBus rev 1.2 interface.
> > +
> > +Device supports direct format for reading output power.
> > +Device supports linear format for reading input voltage, output current,
> > +and temperature.
> > +Device supports VID for reading output voltage.
> > +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 37a5c39784fa..b1344b265976 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> > This driver can also be built as a module. If so, the module will
> > be called max8688.
> >
> > +config SENSORS_MP2949A
> > + tristate "MPS MP2949A"
> > + help
> > + If you say yes here you get hardware monitoring support for MPS
> > + MP2949A Triple Loop Digital Multi-Phase Controller.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called mp2949a.
> > +
> > config SENSORS_MP2975
> > tristate "MPS MP2975"
> > help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index f8dcc27cd56a..bfb55ab12da1 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> > obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> > obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> > obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> > +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> > diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> > new file mode 100644
> > index 000000000000..744c88b8ebca
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/mp2949a.c
> > @@ -0,0 +1,118 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> > + *
> > + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> > + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +#define MP2949A_PAGE_NUM 3
> > +
> > +#define MP2949A_MFR_VR_CONFIG 0xE4
> > +
> > +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> > +{
> > + switch (reg) {
> > + case PMBUS_VOUT_MODE:
> > + /*
> > + * This chip do not support the VOUT_MODE command.
> > + * There is not VOUT_MODE command in MP2949A datasheet P29~P31.
> > + * So there is a EINVAL in here.
> > + */
> > + return -EINVAL;
>
> This is not a reason to add this code. The PMBus core handles this situation.
> Please explain why this is needed. "The chip does not support this command"
> is not a reason.
>
> > + default:
> > + return -ENODATA;
> > + }
> > +}
> > +
> > +static int mp2949a_identify(struct i2c_client *client,
> > + struct pmbus_driver_info *info)
> > +{
> > + int i, ret;
> > +
> > + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> > + ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
> > + if (ret < 0)
> > + return ret;
> > +
> > + /*
> > + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> > + * 1'b1: 5mV (vr12/imvp8)
> > + * 1'b0: 10mv (imvp9)
> > + */
> > + info->vrm_version[i] = (ret & ~BIT(5-i)) ? vr12 : imvp9;
>
> Space before and after '-'.
> Also, why ~ ? This evaluates all bits except the target bit.
>
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static struct pmbus_driver_info mp2949a_info = {
> > + .pages = MP2949A_PAGE_NUM,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = vid,
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .format[PSC_POWER] = direct,
> > + .m[PSC_POWER] = 1,
> > + .b[PSC_POWER] = 0,
> > + .R[PSC_POWER] = 0,
> > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> > + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .identify = mp2949a_identify,
> > + .read_byte_data = mp2949a_read_byte_data,
> > +};
> > +
> > +static int mp2949a_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct pmbus_driver_info *info;
> > +
> > + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> > + GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > +
> > + return pmbus_do_probe(client, info);
> > +}
> > +
> > +static const struct i2c_device_id mp2949a_id[] = {
> > + {"mp2949a", 0},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> > +
> > +static const struct of_device_id mp2949a_of_match[] = {
> > + {.compatible = "mps,mp2949a"},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> > +
> > +static struct i2c_driver mp2949a_driver = {
> > + .driver = {
> > + .name = "mp2949a",
> > + .of_match_table = of_match_ptr(mp2949a_of_match),
> > + },
> > + .probe = mp2949a_probe,
> > + .id_table = mp2949a_id,
> > +};
> > +
> > +module_i2c_driver(mp2949a_driver);
> > +
> > +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> > +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.18.1
> >
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
2021-06-22 6:27 ` teng sterling
@ 2021-06-22 6:52 ` Ainux Wang
0 siblings, 0 replies; 7+ messages in thread
From: Ainux Wang @ 2021-06-22 6:52 UTC (permalink / raw)
To: teng sterling
Cc: jdelvare, Guenter Roeck, Jonathan Corbet, linux-hwmon, linux-doc,
Huacai Chen, Huacai Chen
HI， Yanteng
Thanks for the review. I'll address it all in v4.
Best regards,
Ainux Wang.
On Tue, 22 Jun 2021 at 14:27, teng sterling <sterlingteng@gmail.com> wrote:
>
> <ainux.wang@gmail.com> 于2021年6月22日周二 上午9:50写道：
> >
> > From: "Ainux.Wang" <ainux.wang@gmail.com>
> >
> > Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> > This is a triple-loop, digital, multi-phase controller.
> > This device:
> > - Supports up to three power rail.
> > - Provides 6 pulse-width modulations (PWMs), and can be configured up
> > to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> > and up to 1-phase operation for Rail C.
> > - The PMBus registers are distributed into three pages: Page 0, Page 1,
> > Page 2. Page 0 contains the registers for Rail A and most of the common
> > settings for all of the rails. Page 1 contains register information for
> > Rail B. Page 2 contains register information for Rail C.
> > - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > IMVP9.
> >
> > Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
> >
> > v3:
> > - Added change log here.
> > - Errors in the document have been modified.
> > - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> > - Removed unnecessary vout_params and empty line.
> >
> > v2:
> > - Reference has been added to Documentation/hwmon/index.rst.
> > - Droped 'vendor'.
> > - Removed change codes of the PMBus core and added mp2949a_identify()
> > and mp2949a_read_byte_data() to this driver.
> >
> > v1:
> > - Add support for MPS MP2949A.
> > ---
> Hi，Ainux
>
> Change log goes here. just like:
>
> ...
> Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
> ---
> v3:
> - Added change log here.
> - Errors in the document have been modified.
> - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> - Removed unnecessary vout_params and empty line.
>
> v2:
> - Reference has been added to Documentation/hwmon/index.rst.
> - Droped 'vendor'.
> - Removed change codes of the PMBus core and added mp2949a_identify()
> and mp2949a_read_byte_data() to this driver.
>
> v1:
> - Add support for MPS MP2949A.
>
> Documentation/hwmon/index.rst | 1 +
> ...
>
> Thanks,
>
> Yanteng
>
>
> > Documentation/hwmon/index.rst | 1 +
> > Documentation/hwmon/mp2949a.rst | 44 ++++++++++++
> > drivers/hwmon/pmbus/Kconfig | 9 +++
> > drivers/hwmon/pmbus/Makefile | 1 +
> > drivers/hwmon/pmbus/mp2949a.c | 118 ++++++++++++++++++++++++++++++++
> > 5 files changed, 173 insertions(+)
> > create mode 100644 Documentation/hwmon/mp2949a.rst
> > create mode 100644 drivers/hwmon/pmbus/mp2949a.c
> >
> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> > index 9ed60fa84cbe..56aac3b1678d 100644
> > --- a/Documentation/hwmon/index.rst
> > +++ b/Documentation/hwmon/index.rst
> > @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> > mcp3021
> > menf21bmc
> > mlxreg-fan
> > + mp2949a
> > mp2975
> > nct6683
> > nct6775
> > diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> > new file mode 100644
> > index 000000000000..0235dec70f63
> > --- /dev/null
> > +++ b/Documentation/hwmon/mp2949a.rst
> > @@ -0,0 +1,44 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +Kernel driver mp2949a
> > +====================
> > +
> > +Supported chips:
> > +
> > + * MPS MP2949A
> > +
> > + Prefix: 'mp2949a'
> > +
> > +Author:
> > +
> > + Ainux Wang <ainux.wang@gmail.com>
> > +
> > +Description
> > +-----------
> > +
> > +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> > +triple-loop, digital, multi-phase controller MP2949A.
> > +
> > +This device:
> > +
> > +- Supports up to three power rail.
> > +- Provides 6 pulse-width modulations (PWMs), and can be configured for
> > + to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
> > + and up to 1-phase operation for Rail C.
> > +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> > + Page 2. Page 0 contains the registers for Rail A and most of the common
> > + settings for all of the rails. Page 1 contains register information for
> > + Rail B. Page 2 contains register information for Rail C.
> > +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > + IMVP9.
> > +
> > +Device supports:
> > +
> > +- SVID interface.
> > +- PMBus rev 1.2 interface.
> > +
> > +Device supports direct format for reading output power.
> > +Device supports linear format for reading input voltage, output current,
> > +and temperature.
> > +Device supports VID for reading output voltage.
> > +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 37a5c39784fa..b1344b265976 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> > This driver can also be built as a module. If so, the module will
> > be called max8688.
> >
> > +config SENSORS_MP2949A
> > + tristate "MPS MP2949A"
> > + help
> > + If you say yes here you get hardware monitoring support for MPS
> > + MP2949A Triple Loop Digital Multi-Phase Controller.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called mp2949a.
> > +
> > config SENSORS_MP2975
> > tristate "MPS MP2975"
> > help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index f8dcc27cd56a..bfb55ab12da1 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> > obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> > obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> > obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> > +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> > obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> > obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> > obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> > diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> > new file mode 100644
> > index 000000000000..744c88b8ebca
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/mp2949a.c
> > @@ -0,0 +1,118 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> > + *
> > + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> > + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +#define MP2949A_PAGE_NUM 3
> > +
> > +#define MP2949A_MFR_VR_CONFIG 0xE4
> > +
> > +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> > +{
> > + switch (reg) {
> > + case PMBUS_VOUT_MODE:
> > + /*
> > + * This chip do not support the VOUT_MODE command.
> > + * There is not VOUT_MODE command in MP2949A datasheet P29~P31.
> > + * So there is a EINVAL in here.
> > + */
> > + return -EINVAL;
> > + default:
> > + return -ENODATA;
> > + }
> > +}
> > +
> > +static int mp2949a_identify(struct i2c_client *client,
> > + struct pmbus_driver_info *info)
> > +{
> > + int i, ret;
> > +
> > + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> > + ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
> > + if (ret < 0)
> > + return ret;
> > +
> > + /*
> > + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> > + * 1'b1: 5mV (vr12/imvp8)
> > + * 1'b0: 10mv (imvp9)
> > + */
> > + info->vrm_version[i] = (ret & ~BIT(5-i)) ? vr12 : imvp9;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static struct pmbus_driver_info mp2949a_info = {
> > + .pages = MP2949A_PAGE_NUM,
> > + .format[PSC_VOLTAGE_IN] = linear,
> > + .format[PSC_VOLTAGE_OUT] = vid,
> > + .format[PSC_CURRENT_OUT] = linear,
> > + .format[PSC_TEMPERATURE] = linear,
> > + .format[PSC_POWER] = direct,
> > + .m[PSC_POWER] = 1,
> > + .b[PSC_POWER] = 0,
> > + .R[PSC_POWER] = 0,
> > + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> > + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > + PMBUS_HAVE_POUT,
> > + .identify = mp2949a_identify,
> > + .read_byte_data = mp2949a_read_byte_data,
> > +};
> > +
> > +static int mp2949a_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct pmbus_driver_info *info;
> > +
> > + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> > + GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > +
> > + return pmbus_do_probe(client, info);
> > +}
> > +
> > +static const struct i2c_device_id mp2949a_id[] = {
> > + {"mp2949a", 0},
> > + {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> > +
> > +static const struct of_device_id mp2949a_of_match[] = {
> > + {.compatible = "mps,mp2949a"},
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> > +
> > +static struct i2c_driver mp2949a_driver = {
> > + .driver = {
> > + .name = "mp2949a",
> > + .of_match_table = of_match_ptr(mp2949a_of_match),
> > + },
> > + .probe = mp2949a_probe,
> > + .id_table = mp2949a_id,
> > +};
> > +
> > +module_i2c_driver(mp2949a_driver);
> > +
> > +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> > +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.18.1
> >
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
2021-06-22 8:58 ainux.wang
@ 2021-06-22 9:03 ` Ainux Wang
0 siblings, 0 replies; 7+ messages in thread
From: Ainux Wang @ 2021-06-22 9:03 UTC (permalink / raw)
To: jdelvare, Guenter Roeck, Jonathan Corbet, Ainux Wang
Cc: linux-hwmon, linux-doc, teng sterling, Huacai Chen, Huacai Chen
Hi, Guenter and others,
I'm sorry, it's the wrong subject.
Best regards,
Ainux Wang.
On Tue, 22 Jun 2021 at 16:58, <ainux.wang@gmail.com> wrote:
>
> From: "Ainux.Wang" <ainux.wang@gmail.com>
>
> Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> This is a triple-loop, digital, multi-phase controller.
> This device:
> - Supports up to three power rail.
> - Provides 6 pulse-width modulations (PWMs), and can be configured up
> to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> and up to 1-phase operation for Rail C.
> - The PMBus registers are distributed into three pages: Page 0, Page 1,
> Page 2. Page 0 contains the registers for Rail A and most of the common
> settings for all of the rails. Page 1 contains register information for
> Rail B. Page 2 contains register information for Rail C.
> - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> IMVP9.
>
> Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
>
> v4:
> - Removed mp2949a_read_byte_data().
> - Added space before and after '-' and fixed a bug that is '~' on line 35.
>
> v3:
> - Added change log here.
> - Errors in the document have been modified.
> - Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
> - Removed unnecessary vout_params and empty line.
>
> v2:
> - Reference has been added to Documentation/hwmon/index.rst.
> - Droped 'vendor'.
> - Removed change codes of the PMBus core and added mp2949a_identify()
> and mp2949a_read_byte_data() to this driver.
>
> v1:
> - Add support for MPS MP2949A.
> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/mp2949a.rst | 44 ++++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +++
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/mp2949a.c | 102 ++++++++++++++++++++++++++++++++
> 5 files changed, 157 insertions(+)
> create mode 100644 Documentation/hwmon/mp2949a.rst
> create mode 100644 drivers/hwmon/pmbus/mp2949a.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 9ed60fa84cbe..56aac3b1678d 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> mcp3021
> menf21bmc
> mlxreg-fan
> + mp2949a
> mp2975
> nct6683
> nct6775
> diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> new file mode 100644
> index 000000000000..0235dec70f63
> --- /dev/null
> +++ b/Documentation/hwmon/mp2949a.rst
> @@ -0,0 +1,44 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2949a
> +====================
> +
> +Supported chips:
> +
> + * MPS MP2949A
> +
> + Prefix: 'mp2949a'
> +
> +Author:
> +
> + Ainux Wang <ainux.wang@gmail.com>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +triple-loop, digital, multi-phase controller MP2949A.
> +
> +This device:
> +
> +- Supports up to three power rail.
> +- Provides 6 pulse-width modulations (PWMs), and can be configured for
> + to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
> + and up to 1-phase operation for Rail C.
> +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> + Page 2. Page 0 contains the registers for Rail A and most of the common
> + settings for all of the rails. Page 1 contains register information for
> + Rail B. Page 2 contains register information for Rail C.
> +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> + IMVP9.
> +
> +Device supports:
> +
> +- SVID interface.
> +- PMBus rev 1.2 interface.
> +
> +Device supports direct format for reading output power.
> +Device supports linear format for reading input voltage, output current,
> +and temperature.
> +Device supports VID for reading output voltage.
> +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 37a5c39784fa..b1344b265976 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> This driver can also be built as a module. If so, the module will
> be called max8688.
>
> +config SENSORS_MP2949A
> + tristate "MPS MP2949A"
> + help
> + If you say yes here you get hardware monitoring support for MPS
> + MP2949A Triple Loop Digital Multi-Phase Controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called mp2949a.
> +
> config SENSORS_MP2975
> tristate "MPS MP2975"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index f8dcc27cd56a..bfb55ab12da1 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> +obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
> obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> new file mode 100644
> index 000000000000..d1f36c008e58
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2949a.c
> @@ -0,0 +1,102 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> + *
> + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> + * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +#define MP2949A_PAGE_NUM 3
> +
> +#define MP2949A_MFR_VR_CONFIG 0xE4
> +
> +static int mp2949a_identify(struct i2c_client *client,
> + struct pmbus_driver_info *info)
> +{
> + int i, ret;
> +
> + for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> + ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> + * 1'b1: 5mV (vr12/imvp8)
> + * 1'b0: 10mv (imvp9)
> + */
> + info->vrm_version[i] = (ret & BIT(5 - i)) ? vr12 : imvp9;
> + }
> +
> + return 0;
> +}
> +
> +static struct pmbus_driver_info mp2949a_info = {
> + .pages = MP2949A_PAGE_NUM,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = vid,
> + .format[PSC_CURRENT_OUT] = linear,
> + .format[PSC_TEMPERATURE] = linear,
> + .format[PSC_POWER] = direct,
> + .m[PSC_POWER] = 1,
> + .b[PSC_POWER] = 0,
> + .R[PSC_POWER] = 0,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> + .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_POUT,
> + .identify = mp2949a_identify,
> +};
> +
> +static int mp2949a_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct pmbus_driver_info *info;
> +
> + info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> + GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2949a_id[] = {
> + {"mp2949a", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> +
> +static const struct of_device_id mp2949a_of_match[] = {
> + {.compatible = "mps,mp2949a"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> +
> +static struct i2c_driver mp2949a_driver = {
> + .driver = {
> + .name = "mp2949a",
> + .of_match_table = of_match_ptr(mp2949a_of_match),
> + },
> + .probe = mp2949a_probe,
> + .id_table = mp2949a_id,
> +};
> +
> +module_i2c_driver(mp2949a_driver);
> +
> +MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
> +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> +MODULE_LICENSE("GPL");
> --
> 2.18.1
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A
@ 2021-06-22 8:58 ainux.wang
2021-06-22 9:03 ` Ainux Wang
0 siblings, 1 reply; 7+ messages in thread
From: ainux.wang @ 2021-06-22 8:58 UTC (permalink / raw)
To: jdelvare, linux, corbet, ainux.wang
Cc: linux-hwmon, linux-doc, sterlingteng, chenhuacai, chenhuacai
From: "Ainux.Wang" <ainux.wang@gmail.com>
Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
This is a triple-loop, digital, multi-phase controller.
This device:
- Supports up to three power rail.
- Provides 6 pulse-width modulations (PWMs), and can be configured up
to 6-phase operation for Rail A , up to 2-phase operation for Rail B
and up to 1-phase operation for Rail C.
- The PMBus registers are distributed into three pages: Page 0, Page 1,
Page 2. Page 0 contains the registers for Rail A and most of the common
settings for all of the rails. Page 1 contains register information for
Rail B. Page 2 contains register information for Rail C.
- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
IMVP9.
Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
v4:
- Removed mp2949a_read_byte_data().
- Added space before and after '-' and fixed a bug that is '~' on line 35.
v3:
- Added change log here.
- Errors in the document have been modified.
- Fixed PMBUS_VOUT_MODE to MP2949A_MFR_VR_CONFIG.
- Removed unnecessary vout_params and empty line.
v2:
- Reference has been added to Documentation/hwmon/index.rst.
- Droped 'vendor'.
- Removed change codes of the PMBus core and added mp2949a_identify()
and mp2949a_read_byte_data() to this driver.
v1:
- Add support for MPS MP2949A.
---
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/mp2949a.rst | 44 ++++++++++++++
drivers/hwmon/pmbus/Kconfig | 9 +++
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/mp2949a.c | 102 ++++++++++++++++++++++++++++++++
5 files changed, 157 insertions(+)
create mode 100644 Documentation/hwmon/mp2949a.rst
create mode 100644 drivers/hwmon/pmbus/mp2949a.c
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 9ed60fa84cbe..56aac3b1678d 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
mcp3021
menf21bmc
mlxreg-fan
+ mp2949a
mp2975
nct6683
nct6775
diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
new file mode 100644
index 000000000000..0235dec70f63
--- /dev/null
+++ b/Documentation/hwmon/mp2949a.rst
@@ -0,0 +1,44 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2949a
+====================
+
+Supported chips:
+
+ * MPS MP2949A
+
+ Prefix: 'mp2949a'
+
+Author:
+
+ Ainux Wang <ainux.wang@gmail.com>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+triple-loop, digital, multi-phase controller MP2949A.
+
+This device:
+
+- Supports up to three power rail.
+- Provides 6 pulse-width modulations (PWMs), and can be configured for
+ to 6-phase operation for Rail A , up to 2-phase operation for Rail B,
+ and up to 1-phase operation for Rail C.
+- The PMBus registers are distributed into three pages: Page 0, Page 1,
+ Page 2. Page 0 contains the registers for Rail A and most of the common
+ settings for all of the rails. Page 1 contains register information for
+ Rail B. Page 2 contains register information for Rail C.
+- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
+ IMVP9.
+
+Device supports:
+
+- SVID interface.
+- PMBus rev 1.2 interface.
+
+Device supports direct format for reading output power.
+Device supports linear format for reading input voltage, output current,
+and temperature.
+Device supports VID for reading output voltage.
+The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 37a5c39784fa..b1344b265976 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -248,6 +248,15 @@ config SENSORS_MAX8688
This driver can also be built as a module. If so, the module will
be called max8688.
+config SENSORS_MP2949A
+ tristate "MPS MP2949A"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP2949A Triple Loop Digital Multi-Phase Controller.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp2949a.
+
config SENSORS_MP2975
tristate "MPS MP2975"
help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index f8dcc27cd56a..bfb55ab12da1 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
+obj-$(CONFIG_SENSORS_MP2949A) += mp2949a.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
new file mode 100644
index 000000000000..d1f36c008e58
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2949a.c
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for Monolithic Power Systems MP2949A
+ *
+ * Copyright (c) 2021 Lemote Technologies. All rights reserved.
+ * Copyright (c) 2021 Ainux <ainux.wang@gmail.com>
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+#define MP2949A_PAGE_NUM 3
+
+#define MP2949A_MFR_VR_CONFIG 0xE4
+
+static int mp2949a_identify(struct i2c_client *client,
+ struct pmbus_driver_info *info)
+{
+ int i, ret;
+
+ for (i = 0; i < MP2949A_PAGE_NUM; i++) {
+ ret = pmbus_read_byte_data(client, i, MP2949A_MFR_VR_CONFIG);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Rail A bit 5, Rail B bit 4, Rail C bit 3.
+ * 1'b1: 5mV (vr12/imvp8)
+ * 1'b0: 10mv (imvp9)
+ */
+ info->vrm_version[i] = (ret & BIT(5 - i)) ? vr12 : imvp9;
+ }
+
+ return 0;
+}
+
+static struct pmbus_driver_info mp2949a_info = {
+ .pages = MP2949A_PAGE_NUM,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = vid,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_POWER] = direct,
+ .m[PSC_POWER] = 1,
+ .b[PSC_POWER] = 0,
+ .R[PSC_POWER] = 0,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
+ .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_POUT,
+ .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_POUT,
+ .identify = mp2949a_identify,
+};
+
+static int mp2949a_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct pmbus_driver_info *info;
+
+ info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
+ GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2949a_id[] = {
+ {"mp2949a", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2949a_id);
+
+static const struct of_device_id mp2949a_of_match[] = {
+ {.compatible = "mps,mp2949a"},
+ {}
+};
+MODULE_DEVICE_TABLE(of, mp2949a_of_match);
+
+static struct i2c_driver mp2949a_driver = {
+ .driver = {
+ .name = "mp2949a",
+ .of_match_table = of_match_ptr(mp2949a_of_match),
+ },
+ .probe = mp2949a_probe,
+ .id_table = mp2949a_id,
+};
+
+module_i2c_driver(mp2949a_driver);
+
+MODULE_AUTHOR("Ainux <ainux.wang@gmail.com>");
+MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
+MODULE_LICENSE("GPL");
--
2.18.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-06-22 9:04 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-22 1:50 [PATCH v3] hwmon: (pmbus) Add support for MPS MP2949A ainux.wang
2021-06-22 3:15 ` Guenter Roeck
2021-06-22 6:51 ` Ainux Wang
2021-06-22 6:27 ` teng sterling
2021-06-22 6:52 ` Ainux Wang
2021-06-22 8:58 ainux.wang
2021-06-22 9:03 ` Ainux Wang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.