* [PATCH v3 0/9] phyCORE-i.MX8MP Update
@ 2021-07-07 12:57 Teresa Remmet
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
` (8 more replies)
0 siblings, 9 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:57 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Hello,
this is the third version of the phyCORE-i.MX8MP updates. This
includes also an update of imx8mp.dtsi from kernel and the introduction of a
common imx8mp-u-boot.dtsi.
This version only moves some code from one place/patch to an other.
No intentional functional change to the previous version.
Changes are listed in patches more detailed.
Changes in v3:
- added Reviewed-by tags.
- [2/9] moved binman nodes to common imx8mp-u-boot.dtsi
- made now all debug uart changes in patch:
[4/9] "board: phytec: phycore_imx8mp: Change debug UART"
Changes in v2:
- [5/9] removed hardcoded serverip in environment
- [5/9] removed not needed fec eth defines in board config include
Teresa
Teresa Remmet (9):
arm: dts: imx8mp: Resync imx8mp device tree include
arm: dts: imx8mp: Add common u-boot dtsi
arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
board: phytec: phycore_imx8mp: Change debug UART
board: phytec: phycore_imx8mp: Add fec support
board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
board: phytec: phycore-imx8mp: Enable DVS1 control
arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
board: phytec: imx8mp-phycore: Switch to binman
arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
.../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 47 +-----
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 58 ++++++-
arch/arm/dts/imx8mp-phycore-som.dtsi | 2 +-
arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
arch/arm/dts/imx8mp.dtsi | 146 ++++++++++++++++-
arch/arm/mach-imx/imx8m/Kconfig | 1 +
.../phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 10 ++
board/phytec/phycore_imx8mp/phycore-imx8mp.c | 14 ++
board/phytec/phycore_imx8mp/spl.c | 23 ++-
configs/phycore-imx8mp_defconfig | 12 +-
include/configs/phycore_imx8mp.h | 21 ++-
12 files changed, 424 insertions(+), 202 deletions(-)
create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
create mode 100644 board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg
--
2.25.1
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
@ 2021-07-07 12:57 ` Teresa Remmet
2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
` (7 subsequent siblings)
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:57 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Sync imx8mp include with kernel commit:
d1689cd3c0f4 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
No changes in v2 and v3.
arch/arm/dts/imx8mp.dtsi | 146 +++++++++++++++++++++++++++++++++++++--
1 file changed, 141 insertions(+), 5 deletions(-)
diff --git a/arch/arm/dts/imx8mp.dtsi b/arch/arm/dts/imx8mp.dtsi
index ecccfbb4f5ad..c2d51a46cb3c 100644
--- a/arch/arm/dts/imx8mp.dtsi
+++ b/arch/arm/dts/imx8mp.dtsi
@@ -18,6 +18,7 @@
aliases {
ethernet0 = &fec;
+ ethernet1 = &eqos;
gpio0 = &gpio1;
gpio1 = &gpio2;
gpio2 = &gpio3;
@@ -218,10 +219,12 @@
};
soc@0 {
- compatible = "simple-bus";
+ compatible = "fsl,imx8mp-soc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x0 0x0 0x3e000000>;
+ nvmem-cells = <&imx8mp_uid>;
+ nvmem-cell-names = "soc_unique_id";
aips1: bus@30000000 {
compatible = "fsl,aips-bus", "simple-bus";
@@ -266,7 +269,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 0 144 4>;
+ gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>;
};
gpio4: gpio@30230000 {
@@ -310,6 +313,22 @@
status = "disabled";
};
+ wdog2: watchdog@30290000 {
+ compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt";
+ reg = <0x30290000 0x10000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_WDOG2_ROOT>;
+ status = "disabled";
+ };
+
+ wdog3: watchdog@302a0000 {
+ compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt";
+ reg = <0x302a0000 0x10000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_WDOG3_ROOT>;
+ status = "disabled";
+ };
+
iomuxc: pinctrl@30330000 {
compatible = "fsl,imx8mp-iomuxc";
reg = <0x30330000 0x10000>;
@@ -328,9 +347,17 @@
#address-cells = <1>;
#size-cells = <1>;
+ imx8mp_uid: unique-id@420 {
+ reg = <0x8 0x8>;
+ };
+
cpu_speed_grade: speed-grade@10 {
reg = <0x10 4>;
};
+
+ eth_mac1: mac-address@90 {
+ reg = <0x90 6>;
+ };
};
anatop: anatop@30360000 {
@@ -762,13 +789,40 @@
assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>,
<&clk IMX8MP_CLK_ENET_TIMER>,
<&clk IMX8MP_CLK_ENET_REF>,
- <&clk IMX8MP_CLK_ENET_TIMER>;
+ <&clk IMX8MP_CLK_ENET_PHY_REF>;
assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
<&clk IMX8MP_SYS_PLL2_100M>,
- <&clk IMX8MP_SYS_PLL2_125M>;
- assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+ <&clk IMX8MP_SYS_PLL2_125M>,
+ <&clk IMX8MP_SYS_PLL2_50M>;
+ assigned-clock-rates = <0>, <100000000>, <125000000>, <0>;
fsl,num-tx-queues = <3>;
fsl,num-rx-queues = <3>;
+ nvmem-cells = <ð_mac1>;
+ nvmem-cell-names = "mac-address";
+ fsl,stop-mode = <&gpr 0x10 3>;
+ nvmem_macaddr_swap;
+ status = "disabled";
+ };
+
+ eqos: ethernet@30bf0000 {
+ compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a";
+ reg = <0x30bf0000 0x10000>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "eth_wake_irq", "macirq";
+ clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>,
+ <&clk IMX8MP_CLK_QOS_ENET_ROOT>,
+ <&clk IMX8MP_CLK_ENET_QOS_TIMER>,
+ <&clk IMX8MP_CLK_ENET_QOS>;
+ clock-names = "stmmaceth", "pclk", "ptp_ref", "tx";
+ assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>,
+ <&clk IMX8MP_CLK_ENET_QOS_TIMER>,
+ <&clk IMX8MP_CLK_ENET_QOS>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
+ <&clk IMX8MP_SYS_PLL2_100M>,
+ <&clk IMX8MP_SYS_PLL2_125M>;
+ assigned-clock-rates = <0>, <100000000>, <125000000>;
+ intf_mode = <&gpr 0x4>;
status = "disabled";
};
};
@@ -788,5 +842,87 @@
reg = <0x3d800000 0x400000>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ usb3_phy0: usb-phy@381f0040 {
+ compatible = "fsl,imx8mp-usb-phy";
+ reg = <0x381f0040 0x40>;
+ clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>;
+ clock-names = "phy";
+ assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb3_0: usb@32f10100 {
+ compatible = "fsl,imx8mp-dwc3";
+ reg = <0x32f10100 0x8>;
+ clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "hsio", "suspend";
+ interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x40000000 0x40000000 0xc0000000>;
+ ranges;
+ status = "disabled";
+
+ usb_dwc3_0: usb@38100000 {
+ compatible = "snps,dwc3";
+ reg = <0x38100000 0x10000>;
+ clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+ <&clk IMX8MP_CLK_USB_CORE_REF>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "bus_early", "ref", "suspend";
+ assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
+ assigned-clock-rates = <500000000>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_phy0>, <&usb3_phy0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ snps,dis-u2-freeclk-exists-quirk;
+ };
+
+ };
+
+ usb3_phy1: usb-phy@382f0040 {
+ compatible = "fsl,imx8mp-usb-phy";
+ reg = <0x382f0040 0x40>;
+ clocks = <&clk IMX8MP_CLK_USB_PHY_ROOT>;
+ clock-names = "phy";
+ assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
+ #phy-cells = <0>;
+ };
+
+ usb3_1: usb@32f10108 {
+ compatible = "fsl,imx8mp-dwc3";
+ reg = <0x32f10108 0x8>;
+ clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "hsio", "suspend";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x40000000 0x40000000 0xc0000000>;
+ ranges;
+ status = "disabled";
+
+ usb_dwc3_1: usb@38200000 {
+ compatible = "snps,dwc3";
+ reg = <0x38200000 0x10000>;
+ clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+ <&clk IMX8MP_CLK_USB_CORE_REF>,
+ <&clk IMX8MP_CLK_USB_ROOT>;
+ clock-names = "bus_early", "ref", "suspend";
+ assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
+ assigned-clock-rates = <500000000>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_phy1>, <&usb3_phy1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ snps,dis-u2-freeclk-exists-quirk;
+ };
+ };
};
};
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
@ 2021-07-07 12:57 ` Teresa Remmet
2021-07-09 14:47 ` Tim Harvey
` (2 more replies)
2021-07-07 12:57 ` [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel Teresa Remmet
` (6 subsequent siblings)
8 siblings, 3 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:57 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
Changes in v3:
- Moved binman nodes to common imx8mp-u-boot.dtsi
Changes in v2:
- none
arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
.../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
3 files changed, 153 insertions(+), 178 deletions(-)
create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
diff --git a/arch/arm/dts/imx8mp-evk-u-boot.dtsi b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
index 4162f41cffb6..2abcf1f03d4f 100644
--- a/arch/arm/dts/imx8mp-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
@@ -3,11 +3,9 @@
* Copyright 2019 NXP
*/
-/ {
- binman: binman {
- multiple-images;
- };
+#include "imx8mp-u-boot.dtsi"
+/ {
wdt-reboot {
compatible = "wdt-reboot";
wdt = <&wdog1>;
@@ -21,43 +19,6 @@
};
};
-&{/soc@0} {
- u-boot,dm-pre-reloc;
- u-boot,dm-spl;
-};
-
-&clk {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&osc_32k {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&osc_24m {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&aips1 {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&aips2 {
- u-boot,dm-spl;
-};
-
-&aips3 {
- u-boot,dm-spl;
-};
-
-&iomuxc {
- u-boot,dm-spl;
-};
-
®_usdhc2_vmmc {
u-boot,off-on-delay-us = <20000>;
};
@@ -156,104 +117,4 @@
phy-reset-post-delay = <100>;
};
-&binman {
- u-boot-spl-ddr {
- filename = "u-boot-spl-ddr.bin";
- pad-byte = <0xff>;
- align-size = <4>;
- align = <4>;
- u-boot-spl {
- align-end = <4>;
- };
-
- blob_1: blob-ext@1 {
- filename = "lpddr4_pmu_train_1d_imem_202006.bin";
- size = <0x8000>;
- };
-
- blob_2: blob-ext@2 {
- filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
- size = <0x4000>;
- };
-
- blob_3: blob-ext@3 {
- filename = "lpddr4_pmu_train_2d_imem_202006.bin";
- size = <0x8000>;
- };
-
- blob_4: blob-ext@4 {
- filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
- size = <0x4000>;
- };
- };
-
-
- flash {
- mkimage {
- args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
-
- blob {
- filename = "u-boot-spl-ddr.bin";
- };
- };
- };
-
- itb {
- filename = "u-boot.itb";
-
- fit {
- description = "Configuration to load ATF before U-Boot";
- #address-cells = <1>;
- fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
-
- images {
- uboot {
- description = "U-Boot (64-bit)";
- type = "standalone";
- arch = "arm64";
- compression = "none";
- load = <CONFIG_SYS_TEXT_BASE>;
-
- uboot_blob: blob-ext {
- filename = "u-boot-nodtb.bin";
- };
- };
-
- atf {
- description = "ARM Trusted Firmware";
- type = "firmware";
- arch = "arm64";
- compression = "none";
- load = <0x970000>;
- entry = <0x970000>;
-
- atf_blob: blob-ext {
- filename = "bl31.bin";
- };
- };
-
- fdt {
- description = "NAME";
- type = "flat_dt";
- compression = "none";
-
- uboot_fdt_blob: blob-ext {
- filename = "u-boot.dtb";
- };
- };
- };
-
- configurations {
- default = "conf";
-
- conf {
- description = "NAME";
- firmware = "uboot";
- loadables = "atf";
- fdt = "fdt";
- };
- };
- };
- };
-};
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
index 20e7f63ff91f..6c1528934a98 100644
--- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
@@ -4,6 +4,8 @@
* Author: Teresa Remmet <t.remmet@phytec.de>
*/
+#include "imx8mp-u-boot.dtsi"
+
/ {
wdt-reboot {
compatible = "wdt-reboot";
@@ -12,43 +14,6 @@
};
};
-&{/soc@0} {
- u-boot,dm-pre-reloc;
- u-boot,dm-spl;
-};
-
-&clk {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&osc_32k {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&osc_24m {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&aips1 {
- u-boot,dm-spl;
- u-boot,dm-pre-reloc;
-};
-
-&aips2 {
- u-boot,dm-spl;
-};
-
-&aips3 {
- u-boot,dm-spl;
-};
-
-&iomuxc {
- u-boot,dm-spl;
-};
-
®_usdhc2_vmmc {
u-boot,dm-spl;
};
diff --git a/arch/arm/dts/imx8mp-u-boot.dtsi b/arch/arm/dts/imx8mp-u-boot.dtsi
new file mode 100644
index 000000000000..d61346da3032
--- /dev/null
+++ b/arch/arm/dts/imx8mp-u-boot.dtsi
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+/ {
+ binman: binman {
+ multiple-images;
+ };
+};
+
+&{/soc@0} {
+ u-boot,dm-pre-reloc;
+ u-boot,dm-spl;
+};
+
+&clk {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&osc_32k {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&osc_24m {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+ u-boot,dm-spl;
+};
+
+&aips3 {
+ u-boot,dm-spl;
+};
+
+&iomuxc {
+ u-boot,dm-spl;
+};
+
+&binman {
+ u-boot-spl-ddr {
+ filename = "u-boot-spl-ddr.bin";
+ pad-byte = <0xff>;
+ align-size = <4>;
+ align = <4>;
+
+ u-boot-spl {
+ align-end = <4>;
+ };
+
+ blob_1: blob-ext@1 {
+ filename = "lpddr4_pmu_train_1d_imem_202006.bin";
+ size = <0x8000>;
+ };
+
+ blob_2: blob-ext@2 {
+ filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
+ size = <0x4000>;
+ };
+
+ blob_3: blob-ext@3 {
+ filename = "lpddr4_pmu_train_2d_imem_202006.bin";
+ size = <0x8000>;
+ };
+
+ blob_4: blob-ext@4 {
+ filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
+ size = <0x4000>;
+ };
+ };
+
+ flash {
+ mkimage {
+ args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
+
+ blob {
+ filename = "u-boot-spl-ddr.bin";
+ };
+ };
+ };
+
+ itb {
+ filename = "u-boot.itb";
+
+ fit {
+ description = "Configuration to load ATF before U-Boot";
+ #address-cells = <1>;
+ fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+
+ images {
+ uboot {
+ description = "U-Boot (64-bit)";
+ type = "standalone";
+ arch = "arm64";
+ compression = "none";
+ load = <CONFIG_SYS_TEXT_BASE>;
+
+ uboot_blob: blob-ext {
+ filename = "u-boot-nodtb.bin";
+ };
+ };
+
+ atf {
+ description = "ARM Trusted Firmware";
+ type = "firmware";
+ arch = "arm64";
+ compression = "none";
+ load = <0x970000>;
+ entry = <0x970000>;
+
+ atf_blob: blob-ext {
+ filename = "bl31.bin";
+ };
+ };
+
+ fdt {
+ description = "NAME";
+ type = "flat_dt";
+ compression = "none";
+
+ uboot_fdt_blob: blob-ext {
+ filename = "u-boot.dtb";
+ };
+ };
+ };
+
+ configurations {
+ default = "conf";
+
+ conf {
+ description = "NAME";
+ firmware = "uboot";
+ loadables = "atf";
+ fdt = "fdt";
+ };
+ };
+ };
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
@ 2021-07-07 12:57 ` Teresa Remmet
2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:57 ` [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART Teresa Remmet
` (5 subsequent siblings)
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:57 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
This update includes eqos support and some minor changes.
Synced with kernel commit
412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
Changes in v3:
- Don't sync the debug uart changes here as they are made now in separate
patch
Changes in v2:
- none
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 46 ++++++++++++++++++++-
arch/arm/dts/imx8mp-phycore-som.dtsi | 2 +-
2 files changed, 46 insertions(+), 2 deletions(-)
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
index 0e1a6d953389..2031a9d40bed 100644
--- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
@@ -33,9 +33,33 @@
};
};
+&eqos {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eqos>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ enet-phy-lane-no-swap;
+ };
+ };
+};
+
&i2c2 {
clock-frequency = <400000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>;
sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -90,6 +114,26 @@
};
&iomuxc {
+ pinctrl_eqos: eqosgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
+ MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
+ MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
+ MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
+ MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
+ MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
+ MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
+ MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
+ MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20 0x10
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3
diff --git a/arch/arm/dts/imx8mp-phycore-som.dtsi b/arch/arm/dts/imx8mp-phycore-som.dtsi
index 44a8c2337cee..f3965ec5b31d 100644
--- a/arch/arm/dts/imx8mp-phycore-som.dtsi
+++ b/arch/arm/dts/imx8mp-phycore-som.dtsi
@@ -67,7 +67,7 @@
&i2c1 {
clock-frequency = <400000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (2 preceding siblings ...)
2021-07-07 12:57 ` [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel Teresa Remmet
@ 2021-07-07 12:57 ` Teresa Remmet
2021-07-10 15:54 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support Teresa Remmet
` (4 subsequent siblings)
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:57 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
Changes v3:
- Added imx8mp-phyboard-pollux-rdk.dts debug uart changes to
this patch
Changes v2:
- none
arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 4 ++--
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 12 ++++++------
board/phytec/phycore_imx8mp/spl.c | 6 +++---
include/configs/phycore_imx8mp.h | 4 ++--
4 files changed, 13 insertions(+), 13 deletions(-)
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
index 6c1528934a98..32ed037e3721 100644
--- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
@@ -18,7 +18,7 @@
u-boot,dm-spl;
};
-&pinctrl_uart2 {
+&pinctrl_uart1 {
u-boot,dm-spl;
};
@@ -54,7 +54,7 @@
u-boot,dm-spl;
};
-&uart2 {
+&uart1 {
u-boot,dm-spl;
};
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
index 2031a9d40bed..984a6b9ded8d 100644
--- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
@@ -16,7 +16,7 @@
"phytec,imx8mp-phycore-som", "fsl,imx8mp";
chosen {
- stdout-path = &uart2;
+ stdout-path = &uart1;
};
reg_usdhc2_vmmc: regulator-usdhc2 {
@@ -95,9 +95,9 @@
};
/* debug console */
-&uart2 {
+&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
+ pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
@@ -154,10 +154,10 @@
>;
};
- pinctrl_uart2: uart2grp {
+ pinctrl_uart1: uart1grp {
fsl,pins = <
- MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49
- MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49
+ MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x49
+ MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x49
>;
};
diff --git a/board/phytec/phycore_imx8mp/spl.c b/board/phytec/phycore_imx8mp/spl.c
index f9fa8d1e1281..0bc4c7693b06 100644
--- a/board/phytec/phycore_imx8mp/spl.c
+++ b/board/phytec/phycore_imx8mp/spl.c
@@ -80,8 +80,8 @@ int board_fit_config_name_match(const char *name)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
static iomux_v3_cfg_t const uart_pads[] = {
- MX8MP_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX8MP_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX8MP_PAD_UART1_RXD__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX8MP_PAD_UART1_TXD__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
@@ -107,7 +107,7 @@ void board_init_f(ulong dummy)
arch_cpu_init();
- init_uart_clk(1);
+ init_uart_clk(0);
board_early_init_f();
diff --git a/include/configs/phycore_imx8mp.h b/include/configs/phycore_imx8mp.h
index 04900498507a..e24f223c21d3 100644
--- a/include/configs/phycore_imx8mp.h
+++ b/include/configs/phycore_imx8mp.h
@@ -39,7 +39,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"image=Image\0" \
- "console=ttymxc1,115200\0" \
+ "console=ttymxc0,115200\0" \
"fdt_addr=0x48000000\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
@@ -87,7 +87,7 @@
#define PHYS_SDRAM_SIZE 0x80000000
/* UART */
-#define CONFIG_MXC_UART_BASE UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE SZ_2K
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (3 preceding siblings ...)
2021-07-07 12:57 ` [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART Teresa Remmet
@ 2021-07-07 12:58 ` Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V Teresa Remmet
` (3 subsequent siblings)
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:58 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
Changes in v3:
- none
Changes in v2:
- removed hardcoded serverip in environment
- removed not needed fec eth defines in board config include
board/phytec/phycore_imx8mp/phycore-imx8mp.c | 14 ++++++++++++++
configs/phycore-imx8mp_defconfig | 7 +++++++
include/configs/phycore_imx8mp.h | 17 +++++++++++++++++
3 files changed, 38 insertions(+)
diff --git a/board/phytec/phycore_imx8mp/phycore-imx8mp.c b/board/phytec/phycore_imx8mp/phycore-imx8mp.c
index 67649078c201..a8f082143762 100644
--- a/board/phytec/phycore_imx8mp/phycore-imx8mp.c
+++ b/board/phytec/phycore_imx8mp/phycore-imx8mp.c
@@ -10,11 +10,25 @@
#include <asm/io.h>
#include <asm/mach-imx/boot_mode.h>
#include <env.h>
+#include <miiphy.h>
DECLARE_GLOBAL_DATA_PTR;
+static int setup_fec(void)
+{
+ struct iomuxc_gpr_base_regs *gpr =
+ (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+ /* Use 125M anatop REF_CLK1 for ENET1, not from external */
+ clrsetbits_le32(&gpr->gpr[1], 0x2000, 0);
+
+ return 0;
+}
+
int board_init(void)
{
+ setup_fec();
+
return 0;
}
diff --git a/configs/phycore-imx8mp_defconfig b/configs/phycore-imx8mp_defconfig
index 7f21e8888e0e..a22f5e089d97 100644
--- a/configs/phycore-imx8mp_defconfig
+++ b/configs/phycore-imx8mp_defconfig
@@ -58,6 +58,7 @@ CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_CLK_COMPOSITE_CCF=y
CONFIG_CLK_IMX8MP=y
@@ -79,7 +80,13 @@ CONFIG_MMC_UHS_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_FSL_ESDHC_IMX=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_TI_DP83867=y
CONFIG_DM_ETH=y
+CONFIG_DM_ETH_PHY=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
+CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_IMX8M=y
diff --git a/include/configs/phycore_imx8mp.h b/include/configs/phycore_imx8mp.h
index e24f223c21d3..75f84e60f5da 100644
--- a/include/configs/phycore_imx8mp.h
+++ b/include/configs/phycore_imx8mp.h
@@ -42,6 +42,7 @@
"console=ttymxc0,115200\0" \
"fdt_addr=0x48000000\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=2\0" \
@@ -57,6 +58,22 @@
"else " \
"echo WARN: Cannot load the DT; " \
"fi;\0 " \
+ "nfsroot=/nfs\0" \
+ "netargs=setenv bootargs console=${console} root=/dev/nfs ip=dhcp " \
+ "nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${loadaddr} ${image}; " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi;\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (4 preceding siblings ...)
2021-07-07 12:58 ` [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support Teresa Remmet
@ 2021-07-07 12:58 ` Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:58 ` [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control Teresa Remmet
` (2 subsequent siblings)
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:58 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
No changes in v2 or v3.
board/phytec/phycore_imx8mp/spl.c | 11 ++++++++++-
configs/phycore-imx8mp_defconfig | 1 +
2 files changed, 11 insertions(+), 1 deletion(-)
diff --git a/board/phytec/phycore_imx8mp/spl.c b/board/phytec/phycore_imx8mp/spl.c
index 0bc4c7693b06..815ca9badcba 100644
--- a/board/phytec/phycore_imx8mp/spl.c
+++ b/board/phytec/phycore_imx8mp/spl.c
@@ -62,7 +62,8 @@ int power_init_board(void)
/* BUCKxOUT_DVS0/1 control BUCK123 output */
pmic_reg_write(p, PCA9450_BUCK123_DVS, 0x29);
- /* increase VDD_SOC to typical value 0.95V */
+ /* Increase VDD_SOC and VDD_ARM to OD voltage 0.95V */
+ pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x1C);
pmic_reg_write(p, PCA9450_BUCK2OUT_DVS0, 0x1C);
/* set WDOG_B_CFG to cold reset */
@@ -71,6 +72,14 @@ int power_init_board(void)
return 0;
}
+void spl_board_init(void)
+{
+ /* Set GIC clock to 500Mhz for OD VDD_SOC. */
+ clock_enable(CCGR_GIC, 0);
+ clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5));
+ clock_enable(CCGR_GIC, 1);
+}
+
int board_fit_config_name_match(const char *name)
{
return 0;
diff --git a/configs/phycore-imx8mp_defconfig b/configs/phycore-imx8mp_defconfig
index a22f5e089d97..89c2ac977f47 100644
--- a/configs/phycore-imx8mp_defconfig
+++ b/configs/phycore-imx8mp_defconfig
@@ -25,6 +25,7 @@ CONFIG_OF_SYSTEM_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mp-lpddr4.cfg"
CONFIG_DEFAULT_FDT_FILE="oftree"
CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_BOOTROM_SUPPORT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
CONFIG_SPL_SEPARATE_BSS=y
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (5 preceding siblings ...)
2021-07-07 12:58 ` [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V Teresa Remmet
@ 2021-07-07 12:58 ` Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry Teresa Remmet
2021-07-07 12:58 ` [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman Teresa Remmet
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:58 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Enable DVS1 control through PMIC_STBY_REQ.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
No changes in v2 or v3.
board/phytec/phycore_imx8mp/spl.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/board/phytec/phycore_imx8mp/spl.c b/board/phytec/phycore_imx8mp/spl.c
index 815ca9badcba..19c486e55174 100644
--- a/board/phytec/phycore_imx8mp/spl.c
+++ b/board/phytec/phycore_imx8mp/spl.c
@@ -66,7 +66,11 @@ int power_init_board(void)
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x1C);
pmic_reg_write(p, PCA9450_BUCK2OUT_DVS0, 0x1C);
- /* set WDOG_B_CFG to cold reset */
+ /* Set BUCK1 DVS1 to suspend controlled through PMIC_STBY_REQ */
+ pmic_reg_write(p, PCA9450_BUCK1OUT_DVS1, 0x14);
+ pmic_reg_write(p, PCA9450_BUCK1CTRL, 0x59);
+
+ /* Set WDOG_B_CFG to cold reset */
pmic_reg_write(p, PCA9450_RESET_CTRL, 0xA1);
return 0;
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (6 preceding siblings ...)
2021-07-07 12:58 ` [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control Teresa Remmet
@ 2021-07-07 12:58 ` Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman Teresa Remmet
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:58 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Add missing pinctrl entry in spl.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
No changes in v2 or v3.
arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
index 32ed037e3721..dbc48dfb4841 100644
--- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
@@ -34,6 +34,10 @@
u-boot,dm-spl;
};
+&pinctrl_wdog {
+ u-boot,dm-spl;
+};
+
&gpio1 {
u-boot,dm-spl;
};
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
` (7 preceding siblings ...)
2021-07-07 12:58 ` [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry Teresa Remmet
@ 2021-07-07 12:58 ` Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
8 siblings, 2 replies; 43+ messages in thread
From: Teresa Remmet @ 2021-07-07 12:58 UTC (permalink / raw)
To: u-boot
Cc: Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan,
Jagan Teki, Heiko Schocher
Use now binman for image creation.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
---
Changes in v3:
- binman nodes have been moved to common dtsi so removed from this patch
Changes in v2:
- none
arch/arm/mach-imx/imx8m/Kconfig | 1 +
board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg | 10 ++++++++++
configs/phycore-imx8mp_defconfig | 4 ++--
3 files changed, 13 insertions(+), 2 deletions(-)
create mode 100644 board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg
diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
index 0669363c0f51..ccaf106be5d8 100644
--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
@@ -127,6 +127,7 @@ config TARGET_PHYCORE_IMX8MM
config TARGET_PHYCORE_IMX8MP
bool "PHYTEC PHYCORE i.MX8MP"
+ select BINMAN
select IMX8MP
select SUPPORT_SPL
select IMX8M_LPDDR4
diff --git a/board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg b/board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg
new file mode 100644
index 000000000000..b2920b4908ed
--- /dev/null
+++ b/board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2021 NXP
+ */
+
+#define __ASSEMBLY__
+
+ROM_VERSION v2
+BOOT_FROM sd
+LOADER mkimage.flash.mkimage 0x920000
diff --git a/configs/phycore-imx8mp_defconfig b/configs/phycore-imx8mp_defconfig
index 89c2ac977f47..32d538c8bbbb 100644
--- a/configs/phycore-imx8mp_defconfig
+++ b/configs/phycore-imx8mp_defconfig
@@ -20,9 +20,9 @@ CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_USE_SPL_FIT_GENERATOR is not set
CONFIG_OF_SYSTEM_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/imx8m/imximage-8mp-lpddr4.cfg"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/phytec/phycore_imx8mp/imximage-8mp-sd.cfg"
CONFIG_DEFAULT_FDT_FILE="oftree"
CONFIG_BOARD_LATE_INIT=y
CONFIG_SPL_BOARD_INIT=y
--
2.25.1
^ permalink raw reply related [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
@ 2021-07-09 14:47 ` Tim Harvey
2021-07-10 12:23 ` Heiko Schocher
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2 siblings, 1 reply; 43+ messages in thread
From: Tim Harvey @ 2021-07-09 14:47 UTC (permalink / raw)
To: Teresa Remmet
Cc: u-boot, Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team,
Peng Fan, Jagan Teki, Heiko Schocher
On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
>
> Factor out the common node settings for dm-spl and dm-pre-reloc
> and move them to imx8mp-u-boot.dtsi
>
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
> ---
> Changes in v3:
> - Moved binman nodes to common imx8mp-u-boot.dtsi
> Changes in v2:
> - none
>
> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
> 3 files changed, 153 insertions(+), 178 deletions(-)
> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
>
> diff --git a/arch/arm/dts/imx8mp-evk-u-boot.dtsi b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
> index 4162f41cffb6..2abcf1f03d4f 100644
> --- a/arch/arm/dts/imx8mp-evk-u-boot.dtsi
> +++ b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
> @@ -3,11 +3,9 @@
> * Copyright 2019 NXP
> */
>
> -/ {
> - binman: binman {
> - multiple-images;
> - };
> +#include "imx8mp-u-boot.dtsi"
>
> +/ {
> wdt-reboot {
> compatible = "wdt-reboot";
> wdt = <&wdog1>;
> @@ -21,43 +19,6 @@
> };
> };
>
> -&{/soc@0} {
> - u-boot,dm-pre-reloc;
> - u-boot,dm-spl;
> -};
> -
> -&clk {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&osc_32k {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&osc_24m {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&aips1 {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&aips2 {
> - u-boot,dm-spl;
> -};
> -
> -&aips3 {
> - u-boot,dm-spl;
> -};
> -
> -&iomuxc {
> - u-boot,dm-spl;
> -};
> -
> ®_usdhc2_vmmc {
> u-boot,off-on-delay-us = <20000>;
> };
> @@ -156,104 +117,4 @@
> phy-reset-post-delay = <100>;
> };
>
> -&binman {
> - u-boot-spl-ddr {
> - filename = "u-boot-spl-ddr.bin";
> - pad-byte = <0xff>;
> - align-size = <4>;
> - align = <4>;
>
> - u-boot-spl {
> - align-end = <4>;
> - };
> -
> - blob_1: blob-ext@1 {
> - filename = "lpddr4_pmu_train_1d_imem_202006.bin";
> - size = <0x8000>;
> - };
> -
> - blob_2: blob-ext@2 {
> - filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
> - size = <0x4000>;
> - };
> -
> - blob_3: blob-ext@3 {
> - filename = "lpddr4_pmu_train_2d_imem_202006.bin";
> - size = <0x8000>;
> - };
> -
> - blob_4: blob-ext@4 {
> - filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
> - size = <0x4000>;
> - };
> - };
> -
> -
> - flash {
> - mkimage {
> - args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
> -
> - blob {
> - filename = "u-boot-spl-ddr.bin";
> - };
> - };
> - };
> -
> - itb {
> - filename = "u-boot.itb";
> -
> - fit {
> - description = "Configuration to load ATF before U-Boot";
> - #address-cells = <1>;
> - fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
> -
> - images {
> - uboot {
> - description = "U-Boot (64-bit)";
> - type = "standalone";
> - arch = "arm64";
> - compression = "none";
> - load = <CONFIG_SYS_TEXT_BASE>;
> -
> - uboot_blob: blob-ext {
> - filename = "u-boot-nodtb.bin";
> - };
> - };
> -
> - atf {
> - description = "ARM Trusted Firmware";
> - type = "firmware";
> - arch = "arm64";
> - compression = "none";
> - load = <0x970000>;
> - entry = <0x970000>;
> -
> - atf_blob: blob-ext {
> - filename = "bl31.bin";
> - };
> - };
> -
> - fdt {
> - description = "NAME";
> - type = "flat_dt";
> - compression = "none";
> -
> - uboot_fdt_blob: blob-ext {
> - filename = "u-boot.dtb";
> - };
> - };
> - };
> -
> - configurations {
> - default = "conf";
> -
> - conf {
> - description = "NAME";
> - firmware = "uboot";
> - loadables = "atf";
> - fdt = "fdt";
> - };
> - };
> - };
> - };
> -};
> diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
> index 20e7f63ff91f..6c1528934a98 100644
> --- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
> +++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
> @@ -4,6 +4,8 @@
> * Author: Teresa Remmet <t.remmet@phytec.de>
> */
>
> +#include "imx8mp-u-boot.dtsi"
> +
> / {
> wdt-reboot {
> compatible = "wdt-reboot";
> @@ -12,43 +14,6 @@
> };
> };
>
> -&{/soc@0} {
> - u-boot,dm-pre-reloc;
> - u-boot,dm-spl;
> -};
> -
> -&clk {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&osc_32k {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&osc_24m {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&aips1 {
> - u-boot,dm-spl;
> - u-boot,dm-pre-reloc;
> -};
> -
> -&aips2 {
> - u-boot,dm-spl;
> -};
> -
> -&aips3 {
> - u-boot,dm-spl;
> -};
> -
> -&iomuxc {
> - u-boot,dm-spl;
> -};
> -
> ®_usdhc2_vmmc {
> u-boot,dm-spl;
> };
> diff --git a/arch/arm/dts/imx8mp-u-boot.dtsi b/arch/arm/dts/imx8mp-u-boot.dtsi
> new file mode 100644
> index 000000000000..d61346da3032
> --- /dev/null
> +++ b/arch/arm/dts/imx8mp-u-boot.dtsi
> @@ -0,0 +1,149 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2021 PHYTEC Messtechnik GmbH
> + * Author: Teresa Remmet <t.remmet@phytec.de>
> + */
> +
> +/ {
> + binman: binman {
> + multiple-images;
> + };
> +};
> +
> +&{/soc@0} {
> + u-boot,dm-pre-reloc;
> + u-boot,dm-spl;
> +};
> +
> +&clk {
> + u-boot,dm-spl;
> + u-boot,dm-pre-reloc;
> +};
> +
> +&osc_32k {
> + u-boot,dm-spl;
> + u-boot,dm-pre-reloc;
> +};
> +
> +&osc_24m {
> + u-boot,dm-spl;
> + u-boot,dm-pre-reloc;
> +};
> +
> +&aips1 {
> + u-boot,dm-spl;
> + u-boot,dm-pre-reloc;
> +};
> +
> +&aips2 {
> + u-boot,dm-spl;
> +};
> +
> +&aips3 {
> + u-boot,dm-spl;
> +};
> +
> +&iomuxc {
> + u-boot,dm-spl;
> +};
> +
> +&binman {
> + u-boot-spl-ddr {
> + filename = "u-boot-spl-ddr.bin";
> + pad-byte = <0xff>;
> + align-size = <4>;
> + align = <4>;
> +
> + u-boot-spl {
> + align-end = <4>;
> + };
> +
> + blob_1: blob-ext@1 {
> + filename = "lpddr4_pmu_train_1d_imem_202006.bin";
> + size = <0x8000>;
> + };
> +
> + blob_2: blob-ext@2 {
> + filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
> + size = <0x4000>;
> + };
> +
> + blob_3: blob-ext@3 {
> + filename = "lpddr4_pmu_train_2d_imem_202006.bin";
> + size = <0x8000>;
> + };
> +
> + blob_4: blob-ext@4 {
> + filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
> + size = <0x4000>;
> + };
> + };
> +
> + flash {
> + mkimage {
> + args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
> +
> + blob {
> + filename = "u-boot-spl-ddr.bin";
> + };
> + };
> + };
> +
> + itb {
> + filename = "u-boot.itb";
> +
> + fit {
> + description = "Configuration to load ATF before U-Boot";
> + #address-cells = <1>;
> + fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
> +
> + images {
> + uboot {
> + description = "U-Boot (64-bit)";
> + type = "standalone";
> + arch = "arm64";
> + compression = "none";
> + load = <CONFIG_SYS_TEXT_BASE>;
> +
> + uboot_blob: blob-ext {
> + filename = "u-boot-nodtb.bin";
> + };
> + };
> +
> + atf {
> + description = "ARM Trusted Firmware";
> + type = "firmware";
> + arch = "arm64";
> + compression = "none";
> + load = <0x970000>;
> + entry = <0x970000>;
> +
> + atf_blob: blob-ext {
> + filename = "bl31.bin";
> + };
> + };
> +
> + fdt {
> + description = "NAME";
> + type = "flat_dt";
> + compression = "none";
> +
> + uboot_fdt_blob: blob-ext {
> + filename = "u-boot.dtb";
> + };
> + };
> + };
> +
> + configurations {
> + default = "conf";
> +
> + conf {
> + description = "NAME";
> + firmware = "uboot";
> + loadables = "atf";
> + fdt = "fdt";
> + };
> + };
> + };
> + };
> +};
> --
> 2.25.1
>
Teresa,
I've noticed many of the imx8m boards migrating to using binman for
image packaging.
Doesn't this change from having a single flash.bin encompasing the SPL
and U-Boot proper to having split files? I noticed that happened with
imx8mm_evk for example when it switched to binman.
What are the benefits to using binman?
Thanks,
Tim
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-09 14:47 ` Tim Harvey
@ 2021-07-10 12:23 ` Heiko Schocher
2021-07-12 16:42 ` Tim Harvey
2021-08-13 12:55 ` Fabio Estevam
0 siblings, 2 replies; 43+ messages in thread
From: Heiko Schocher @ 2021-07-10 12:23 UTC (permalink / raw)
To: Tim Harvey, Teresa Remmet
Cc: u-boot, Stefano Babic, Fabio Estevam, NXP i . MX U-Boot Team,
Peng Fan, Jagan Teki
Hello Tim,
On 09.07.21 16:47, Tim Harvey wrote:
> On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
>>
>> Factor out the common node settings for dm-spl and dm-pre-reloc
>> and move them to imx8mp-u-boot.dtsi
>>
>> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
>> Reviewed-by: Fabio Estevam <festevam@gmail.com>
>> Reviewed-by: Heiko Schocher <hs@denx.de>
>> ---
>> Changes in v3:
>> - Moved binman nodes to common imx8mp-u-boot.dtsi
>> Changes in v2:
>> - none
>>
>> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
>> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
>> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
>> 3 files changed, 153 insertions(+), 178 deletions(-)
>> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
>>
>> diff --git a/arch/arm/dts/imx8mp-evk-u-boot.dtsi b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
>> index 4162f41cffb6..2abcf1f03d4f 100644
>> --- a/arch/arm/dts/imx8mp-evk-u-boot.dtsi
>> +++ b/arch/arm/dts/imx8mp-evk-u-boot.dtsi
>> @@ -3,11 +3,9 @@
>> * Copyright 2019 NXP
>> */
>>
>> -/ {
>> - binman: binman {
>> - multiple-images;
>> - };
>> +#include "imx8mp-u-boot.dtsi"
>>
>> +/ {
>> wdt-reboot {
>> compatible = "wdt-reboot";
>> wdt = <&wdog1>;
>> @@ -21,43 +19,6 @@
>> };
>> };
>>
>> -&{/soc@0} {
>> - u-boot,dm-pre-reloc;
>> - u-boot,dm-spl;
>> -};
>> -
>> -&clk {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&osc_32k {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&osc_24m {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&aips1 {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&aips2 {
>> - u-boot,dm-spl;
>> -};
>> -
>> -&aips3 {
>> - u-boot,dm-spl;
>> -};
>> -
>> -&iomuxc {
>> - u-boot,dm-spl;
>> -};
>> -
>> ®_usdhc2_vmmc {
>> u-boot,off-on-delay-us = <20000>;
>> };
>> @@ -156,104 +117,4 @@
>> phy-reset-post-delay = <100>;
>> };
>>
>> -&binman {
>> - u-boot-spl-ddr {
>> - filename = "u-boot-spl-ddr.bin";
>> - pad-byte = <0xff>;
>> - align-size = <4>;
>> - align = <4>;
>>
>> - u-boot-spl {
>> - align-end = <4>;
>> - };
>> -
>> - blob_1: blob-ext@1 {
>> - filename = "lpddr4_pmu_train_1d_imem_202006.bin";
>> - size = <0x8000>;
>> - };
>> -
>> - blob_2: blob-ext@2 {
>> - filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
>> - size = <0x4000>;
>> - };
>> -
>> - blob_3: blob-ext@3 {
>> - filename = "lpddr4_pmu_train_2d_imem_202006.bin";
>> - size = <0x8000>;
>> - };
>> -
>> - blob_4: blob-ext@4 {
>> - filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
>> - size = <0x4000>;
>> - };
>> - };
>> -
>> -
>> - flash {
>> - mkimage {
>> - args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
>> -
>> - blob {
>> - filename = "u-boot-spl-ddr.bin";
>> - };
>> - };
>> - };
>> -
>> - itb {
>> - filename = "u-boot.itb";
>> -
>> - fit {
>> - description = "Configuration to load ATF before U-Boot";
>> - #address-cells = <1>;
>> - fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
>> -
>> - images {
>> - uboot {
>> - description = "U-Boot (64-bit)";
>> - type = "standalone";
>> - arch = "arm64";
>> - compression = "none";
>> - load = <CONFIG_SYS_TEXT_BASE>;
>> -
>> - uboot_blob: blob-ext {
>> - filename = "u-boot-nodtb.bin";
>> - };
>> - };
>> -
>> - atf {
>> - description = "ARM Trusted Firmware";
>> - type = "firmware";
>> - arch = "arm64";
>> - compression = "none";
>> - load = <0x970000>;
>> - entry = <0x970000>;
>> -
>> - atf_blob: blob-ext {
>> - filename = "bl31.bin";
>> - };
>> - };
>> -
>> - fdt {
>> - description = "NAME";
>> - type = "flat_dt";
>> - compression = "none";
>> -
>> - uboot_fdt_blob: blob-ext {
>> - filename = "u-boot.dtb";
>> - };
>> - };
>> - };
>> -
>> - configurations {
>> - default = "conf";
>> -
>> - conf {
>> - description = "NAME";
>> - firmware = "uboot";
>> - loadables = "atf";
>> - fdt = "fdt";
>> - };
>> - };
>> - };
>> - };
>> -};
>> diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
>> index 20e7f63ff91f..6c1528934a98 100644
>> --- a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
>> +++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
>> @@ -4,6 +4,8 @@
>> * Author: Teresa Remmet <t.remmet@phytec.de>
>> */
>>
>> +#include "imx8mp-u-boot.dtsi"
>> +
>> / {
>> wdt-reboot {
>> compatible = "wdt-reboot";
>> @@ -12,43 +14,6 @@
>> };
>> };
>>
>> -&{/soc@0} {
>> - u-boot,dm-pre-reloc;
>> - u-boot,dm-spl;
>> -};
>> -
>> -&clk {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&osc_32k {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&osc_24m {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&aips1 {
>> - u-boot,dm-spl;
>> - u-boot,dm-pre-reloc;
>> -};
>> -
>> -&aips2 {
>> - u-boot,dm-spl;
>> -};
>> -
>> -&aips3 {
>> - u-boot,dm-spl;
>> -};
>> -
>> -&iomuxc {
>> - u-boot,dm-spl;
>> -};
>> -
>> ®_usdhc2_vmmc {
>> u-boot,dm-spl;
>> };
>> diff --git a/arch/arm/dts/imx8mp-u-boot.dtsi b/arch/arm/dts/imx8mp-u-boot.dtsi
>> new file mode 100644
>> index 000000000000..d61346da3032
>> --- /dev/null
>> +++ b/arch/arm/dts/imx8mp-u-boot.dtsi
>> @@ -0,0 +1,149 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +/*
>> + * Copyright (C) 2021 PHYTEC Messtechnik GmbH
>> + * Author: Teresa Remmet <t.remmet@phytec.de>
>> + */
>> +
>> +/ {
>> + binman: binman {
>> + multiple-images;
>> + };
>> +};
>> +
>> +&{/soc@0} {
>> + u-boot,dm-pre-reloc;
>> + u-boot,dm-spl;
>> +};
>> +
>> +&clk {
>> + u-boot,dm-spl;
>> + u-boot,dm-pre-reloc;
>> +};
>> +
>> +&osc_32k {
>> + u-boot,dm-spl;
>> + u-boot,dm-pre-reloc;
>> +};
>> +
>> +&osc_24m {
>> + u-boot,dm-spl;
>> + u-boot,dm-pre-reloc;
>> +};
>> +
>> +&aips1 {
>> + u-boot,dm-spl;
>> + u-boot,dm-pre-reloc;
>> +};
>> +
>> +&aips2 {
>> + u-boot,dm-spl;
>> +};
>> +
>> +&aips3 {
>> + u-boot,dm-spl;
>> +};
>> +
>> +&iomuxc {
>> + u-boot,dm-spl;
>> +};
>> +
>> +&binman {
>> + u-boot-spl-ddr {
>> + filename = "u-boot-spl-ddr.bin";
>> + pad-byte = <0xff>;
>> + align-size = <4>;
>> + align = <4>;
>> +
>> + u-boot-spl {
>> + align-end = <4>;
>> + };
>> +
>> + blob_1: blob-ext@1 {
>> + filename = "lpddr4_pmu_train_1d_imem_202006.bin";
>> + size = <0x8000>;
>> + };
>> +
>> + blob_2: blob-ext@2 {
>> + filename = "lpddr4_pmu_train_1d_dmem_202006.bin";
>> + size = <0x4000>;
>> + };
>> +
>> + blob_3: blob-ext@3 {
>> + filename = "lpddr4_pmu_train_2d_imem_202006.bin";
>> + size = <0x8000>;
>> + };
>> +
>> + blob_4: blob-ext@4 {
>> + filename = "lpddr4_pmu_train_2d_dmem_202006.bin";
>> + size = <0x4000>;
>> + };
>> + };
>> +
>> + flash {
>> + mkimage {
>> + args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x920000";
>> +
>> + blob {
>> + filename = "u-boot-spl-ddr.bin";
>> + };
>> + };
>> + };
>> +
>> + itb {
>> + filename = "u-boot.itb";
>> +
>> + fit {
>> + description = "Configuration to load ATF before U-Boot";
>> + #address-cells = <1>;
>> + fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
>> +
>> + images {
>> + uboot {
>> + description = "U-Boot (64-bit)";
>> + type = "standalone";
>> + arch = "arm64";
>> + compression = "none";
>> + load = <CONFIG_SYS_TEXT_BASE>;
>> +
>> + uboot_blob: blob-ext {
>> + filename = "u-boot-nodtb.bin";
>> + };
>> + };
>> +
>> + atf {
>> + description = "ARM Trusted Firmware";
>> + type = "firmware";
>> + arch = "arm64";
>> + compression = "none";
>> + load = <0x970000>;
>> + entry = <0x970000>;
>> +
>> + atf_blob: blob-ext {
>> + filename = "bl31.bin";
>> + };
>> + };
>> +
>> + fdt {
>> + description = "NAME";
>> + type = "flat_dt";
>> + compression = "none";
>> +
>> + uboot_fdt_blob: blob-ext {
>> + filename = "u-boot.dtb";
>> + };
>> + };
>> + };
>> +
>> + configurations {
>> + default = "conf";
>> +
>> + conf {
>> + description = "NAME";
>> + firmware = "uboot";
>> + loadables = "atf";
>> + fdt = "fdt";
>> + };
>> + };
>> + };
>> + };
>> +};
>> --
>> 2.25.1
>>
>
> Teresa,
>
> I've noticed many of the imx8m boards migrating to using binman for
> image packaging.
>
> Doesn't this change from having a single flash.bin encompasing the SPL
> and U-Boot proper to having split files? I noticed that happened with
> imx8mm_evk for example when it switched to binman.
Yes, but you can easy generate there a single image again.
> What are the benefits to using binman?
Beside the pros from binmal in general, I see the benefit in special
for imx8mp, that you can get all infos you need for signing the image
from within the image. No need to save some log output from U-Boot
build and parse this output ...
bye,
Heiko
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs@denx.de
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
@ 2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:52 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Sync imx8mp include with kernel commit:
> d1689cd3c0f4 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
2021-07-07 12:57 ` [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel Teresa Remmet
@ 2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:52 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> This update includes eqos support and some minor changes.
> Synced with kernel commit
> 412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
2021-07-07 12:58 ` [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V Teresa Remmet
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Increase VDD_ARM to prevent timing issues as VDD_SOC is
> used in OD mode. Also increase GIC clock.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support
2021-07-07 12:58 ` [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support Teresa Remmet
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Enable support for the fec ethernet on phyCORE-i.MX8MP.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
2021-07-09 14:47 ` Tim Harvey
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2 siblings, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Factor out the common node settings for dm-spl and dm-pre-reloc
> and move them to imx8mp-u-boot.dtsi
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control
2021-07-07 12:58 ` [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control Teresa Remmet
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Enable DVS1 control through PMIC_STBY_REQ.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
2021-07-07 12:58 ` [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry Teresa Remmet
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Add missing pinctrl entry in spl.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman
2021-07-07 12:58 ` [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman Teresa Remmet
@ 2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:53 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Use now binman for image creation.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART
2021-07-07 12:57 ` [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART Teresa Remmet
@ 2021-07-10 15:54 ` sbabic
2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 15:54 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> With the first redesign the debug UART had changed from
> UART2 to UART1.
> As the first hardware revision is considered as alpha and
> will not be supported in future. The old setup will not
> be preserved.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
2021-07-10 15:52 ` sbabic
@ 2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:35 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Sync imx8mp include with kernel commit:
> d1689cd3c0f4 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
2021-07-07 12:57 ` [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel Teresa Remmet
2021-07-10 15:52 ` sbabic
@ 2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:35 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> This update includes eqos support and some minor changes.
> Synced with kernel commit
> 412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
2021-07-07 12:58 ` [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V Teresa Remmet
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:35 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:35 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Increase VDD_ARM to prevent timing issues as VDD_SOC is
> used in OD mode. Also increase GIC clock.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
2021-07-09 14:47 ` Tim Harvey
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:36 ` sbabic
2 siblings, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Factor out the common node settings for dm-spl and dm-pre-reloc
> and move them to imx8mp-u-boot.dtsi
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support
2021-07-07 12:58 ` [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support Teresa Remmet
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Enable support for the fec ethernet on phyCORE-i.MX8MP.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control
2021-07-07 12:58 ` [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control Teresa Remmet
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Enable DVS1 control through PMIC_STBY_REQ.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
2021-07-07 12:58 ` [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry Teresa Remmet
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Add missing pinctrl entry in spl.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman
2021-07-07 12:58 ` [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman Teresa Remmet
2021-07-10 15:53 ` sbabic
@ 2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> Use now binman for image creation.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART
2021-07-07 12:57 ` [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART Teresa Remmet
2021-07-10 15:54 ` sbabic
@ 2021-07-10 19:36 ` sbabic
1 sibling, 0 replies; 43+ messages in thread
From: sbabic @ 2021-07-10 19:36 UTC (permalink / raw)
To: Teresa Remmet, u-boot
> With the first redesign the debug UART had changed from
> UART2 to UART1.
> As the first hardware revision is considered as alpha and
> will not be supported in future. The old setup will not
> be preserved.
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> Reviewed-by: Heiko Schocher <hs@denx.de>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-10 12:23 ` Heiko Schocher
@ 2021-07-12 16:42 ` Tim Harvey
2021-07-12 19:43 ` Simon Glass
2021-07-19 4:16 ` Heiko Schocher
2021-08-13 12:55 ` Fabio Estevam
1 sibling, 2 replies; 43+ messages in thread
From: Tim Harvey @ 2021-07-12 16:42 UTC (permalink / raw)
To: hs
Cc: Teresa Remmet, u-boot, Stefano Babic, Fabio Estevam,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki, Simon Glass
On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
>
> Hello Tim,
>
> On 09.07.21 16:47, Tim Harvey wrote:
> > On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
> >>
> >> Factor out the common node settings for dm-spl and dm-pre-reloc
> >> and move them to imx8mp-u-boot.dtsi
> >>
> >> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> >> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> >> Reviewed-by: Heiko Schocher <hs@denx.de>
> >> ---
> >> Changes in v3:
> >> - Moved binman nodes to common imx8mp-u-boot.dtsi
> >> Changes in v2:
> >> - none
> >>
> >> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
> >> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
> >> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
> >> 3 files changed, 153 insertions(+), 178 deletions(-)
> >> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
> >>
<snip>
> >>
> >
> > Teresa,
> >
> > I've noticed many of the imx8m boards migrating to using binman for
> > image packaging.
> >
> > Doesn't this change from having a single flash.bin encompasing the SPL
> > and U-Boot proper to having split files? I noticed that happened with
> > imx8mm_evk for example when it switched to binman.
>
> Yes, but you can easy generate there a single image again.
>
> > What are the benefits to using binman?
>
> Beside the pros from binmal in general, I see the benefit in special
> for imx8mp, that you can get all infos you need for signing the image
> from within the image. No need to save some log output from U-Boot
> build and parse this output ...
>
(+cc Simon)
Heiko,
And what are the pros from binman in general? I've read over
tools/binman/binman.rst so I'm assuming you mean what is described
there as benefits.
How do you get all the details needed for signing the image from binman?
If I make imx8mm_evk_defconfig which produces via binman flash.bin and
u-boot.itb I get the following:
$ ./tools/binman/binman ls -i flash.bin
binman: Cannot find FDT map in image
$ ./tools/binman/binman ls -i u-boot.itb
binman: Cannot find FDT map in image
I would very much like to understand how to use binman to get the
various offsets needed for signing an IMX image for use with HAB.
Thanks,
Tim
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-12 16:42 ` Tim Harvey
@ 2021-07-12 19:43 ` Simon Glass
2021-07-12 20:58 ` Tim Harvey
2021-07-19 4:16 ` Heiko Schocher
1 sibling, 1 reply; 43+ messages in thread
From: Simon Glass @ 2021-07-12 19:43 UTC (permalink / raw)
To: Tim Harvey
Cc: Heiko Schocher, Teresa Remmet, u-boot, Stefano Babic,
Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Tim,
On Mon, 12 Jul 2021 at 10:42, Tim Harvey <tharvey@gateworks.com> wrote:
>
> On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
> >
> > Hello Tim,
> >
> > On 09.07.21 16:47, Tim Harvey wrote:
> > > On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
> > >>
> > >> Factor out the common node settings for dm-spl and dm-pre-reloc
> > >> and move them to imx8mp-u-boot.dtsi
> > >>
> > >> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > >> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> > >> Reviewed-by: Heiko Schocher <hs@denx.de>
> > >> ---
> > >> Changes in v3:
> > >> - Moved binman nodes to common imx8mp-u-boot.dtsi
> > >> Changes in v2:
> > >> - none
> > >>
> > >> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
> > >> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
> > >> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
> > >> 3 files changed, 153 insertions(+), 178 deletions(-)
> > >> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
> > >>
> <snip>
> > >>
> > >
> > > Teresa,
> > >
> > > I've noticed many of the imx8m boards migrating to using binman for
> > > image packaging.
> > >
> > > Doesn't this change from having a single flash.bin encompasing the SPL
> > > and U-Boot proper to having split files? I noticed that happened with
> > > imx8mm_evk for example when it switched to binman.
> >
> > Yes, but you can easy generate there a single image again.
> >
> > > What are the benefits to using binman?
> >
> > Beside the pros from binmal in general, I see the benefit in special
> > for imx8mp, that you can get all infos you need for signing the image
> > from within the image. No need to save some log output from U-Boot
> > build and parse this output ...
> >
>
> (+cc Simon)
>
> Heiko,
>
> And what are the pros from binman in general? I've read over
> tools/binman/binman.rst so I'm assuming you mean what is described
> there as benefits.
>
> How do you get all the details needed for signing the image from binman?
>
> If I make imx8mm_evk_defconfig which produces via binman flash.bin and
> u-boot.itb I get the following:
>
> $ ./tools/binman/binman ls -i flash.bin
> binman: Cannot find FDT map in image
> $ ./tools/binman/binman ls -i u-boot.itb
> binman: Cannot find FDT map in image
As the message says, you need an 'fdtmap' in the image:
fdtmap {
}:
>
> I would very much like to understand how to use binman to get the
> various offsets needed for signing an IMX image for use with HAB.
You should be able to add signing support to binman for your use case.
See for example how vblock.py works.
Regards,
Simon
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-12 19:43 ` Simon Glass
@ 2021-07-12 20:58 ` Tim Harvey
2021-07-13 20:17 ` Simon Glass
0 siblings, 1 reply; 43+ messages in thread
From: Tim Harvey @ 2021-07-12 20:58 UTC (permalink / raw)
To: Simon Glass
Cc: Heiko Schocher, Teresa Remmet, u-boot, Stefano Babic,
Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
On Mon, Jul 12, 2021 at 12:44 PM Simon Glass <sjg@chromium.org> wrote:
>
> Hi Tim,
>
> On Mon, 12 Jul 2021 at 10:42, Tim Harvey <tharvey@gateworks.com> wrote:
> >
> > On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
> > >
> > > Hello Tim,
> > >
> > > On 09.07.21 16:47, Tim Harvey wrote:
> > > > On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
> > > >>
> > > >> Factor out the common node settings for dm-spl and dm-pre-reloc
> > > >> and move them to imx8mp-u-boot.dtsi
> > > >>
> > > >> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > > >> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> > > >> Reviewed-by: Heiko Schocher <hs@denx.de>
> > > >> ---
> > > >> Changes in v3:
> > > >> - Moved binman nodes to common imx8mp-u-boot.dtsi
> > > >> Changes in v2:
> > > >> - none
> > > >>
> > > >> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
> > > >> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
> > > >> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
> > > >> 3 files changed, 153 insertions(+), 178 deletions(-)
> > > >> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
> > > >>
> > <snip>
> > > >>
> > > >
> > > > Teresa,
> > > >
> > > > I've noticed many of the imx8m boards migrating to using binman for
> > > > image packaging.
> > > >
> > > > Doesn't this change from having a single flash.bin encompasing the SPL
> > > > and U-Boot proper to having split files? I noticed that happened with
> > > > imx8mm_evk for example when it switched to binman.
> > >
> > > Yes, but you can easy generate there a single image again.
> > >
> > > > What are the benefits to using binman?
> > >
> > > Beside the pros from binmal in general, I see the benefit in special
> > > for imx8mp, that you can get all infos you need for signing the image
> > > from within the image. No need to save some log output from U-Boot
> > > build and parse this output ...
> > >
> >
> > (+cc Simon)
> >
> > Heiko,
> >
> > And what are the pros from binman in general? I've read over
> > tools/binman/binman.rst so I'm assuming you mean what is described
> > there as benefits.
> >
> > How do you get all the details needed for signing the image from binman?
> >
> > If I make imx8mm_evk_defconfig which produces via binman flash.bin and
> > u-boot.itb I get the following:
> >
> > $ ./tools/binman/binman ls -i flash.bin
> > binman: Cannot find FDT map in image
> > $ ./tools/binman/binman ls -i u-boot.itb
> > binman: Cannot find FDT map in image
>
> As the message says, you need an 'fdtmap' in the image:
>
> fdtmap {
> }:
>
Simon,
Sorry I still don't quite understand:
diff --git a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
index f200afac9f..c6d8932fa4 100644
--- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
@@ -163,6 +163,9 @@
itb {
filename = "u-boot.itb";
+ fdtmap {
+ };
+
fit {
description = "Configuration to load ATF before U-Boot";
#address-cells = <1>;
$ make imx8mm_evk_defconfig
$ make
$ ./tools/binman/binman ls -i u-boot.itb
Name Image-pos Size Entry-type Offset Uncomp-size
------------------------------------------------------------------
main-section 0 a3875 section 0
fdtmap 0 48d fdtmap 0
fit 48d a33e8 fit 48d
For signing we need the loadaddr/offset/size of the components within
the FIT image. Since binman is calling mkimage to create FIT images it
seems outside the scope of binman to be able to dump details on the
actual FIT image. Perhaps mkimage or another tool is to be used for
that detail?
> >
> > I would very much like to understand how to use binman to get the
> > various offsets needed for signing an IMX image for use with HAB.
>
> You should be able to add signing support to binman for your use case.
> See for example how vblock.py works.
I see... so your saying instead of using an external tool to generate
a txt template with the offset/size values for the various blobs
instead we need to implement for example a habv4.py to add a habv4
entry and the python class would have access to the content handles to
determine the addr/size in order to create the text template file fed
to the NXP code signing tool?
Regards,
Tim
^ permalink raw reply related [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-12 20:58 ` Tim Harvey
@ 2021-07-13 20:17 ` Simon Glass
2021-07-19 4:18 ` Heiko Schocher
0 siblings, 1 reply; 43+ messages in thread
From: Simon Glass @ 2021-07-13 20:17 UTC (permalink / raw)
To: Tim Harvey
Cc: Heiko Schocher, Teresa Remmet, u-boot, Stefano Babic,
Fabio Estevam, NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Tim,
On Mon, 12 Jul 2021 at 14:58, Tim Harvey <tharvey@gateworks.com> wrote:
>
> On Mon, Jul 12, 2021 at 12:44 PM Simon Glass <sjg@chromium.org> wrote:
> >
> > Hi Tim,
> >
> > On Mon, 12 Jul 2021 at 10:42, Tim Harvey <tharvey@gateworks.com> wrote:
> > >
> > > On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
> > > >
> > > > Hello Tim,
> > > >
> > > > On 09.07.21 16:47, Tim Harvey wrote:
> > > > > On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
> > > > >>
> > > > >> Factor out the common node settings for dm-spl and dm-pre-reloc
> > > > >> and move them to imx8mp-u-boot.dtsi
> > > > >>
> > > > >> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > > > >> Reviewed-by: Fabio Estevam <festevam@gmail.com>
> > > > >> Reviewed-by: Heiko Schocher <hs@denx.de>
> > > > >> ---
> > > > >> Changes in v3:
> > > > >> - Moved binman nodes to common imx8mp-u-boot.dtsi
> > > > >> Changes in v2:
> > > > >> - none
> > > > >>
> > > > >> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
> > > > >> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
> > > > >> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
> > > > >> 3 files changed, 153 insertions(+), 178 deletions(-)
> > > > >> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
> > > > >>
> > > <snip>
> > > > >>
> > > > >
> > > > > Teresa,
> > > > >
> > > > > I've noticed many of the imx8m boards migrating to using binman for
> > > > > image packaging.
> > > > >
> > > > > Doesn't this change from having a single flash.bin encompasing the SPL
> > > > > and U-Boot proper to having split files? I noticed that happened with
> > > > > imx8mm_evk for example when it switched to binman.
> > > >
> > > > Yes, but you can easy generate there a single image again.
> > > >
> > > > > What are the benefits to using binman?
> > > >
> > > > Beside the pros from binmal in general, I see the benefit in special
> > > > for imx8mp, that you can get all infos you need for signing the image
> > > > from within the image. No need to save some log output from U-Boot
> > > > build and parse this output ...
> > > >
> > >
> > > (+cc Simon)
> > >
> > > Heiko,
> > >
> > > And what are the pros from binman in general? I've read over
> > > tools/binman/binman.rst so I'm assuming you mean what is described
> > > there as benefits.
> > >
> > > How do you get all the details needed for signing the image from binman?
> > >
> > > If I make imx8mm_evk_defconfig which produces via binman flash.bin and
> > > u-boot.itb I get the following:
> > >
> > > $ ./tools/binman/binman ls -i flash.bin
> > > binman: Cannot find FDT map in image
> > > $ ./tools/binman/binman ls -i u-boot.itb
> > > binman: Cannot find FDT map in image
> >
> > As the message says, you need an 'fdtmap' in the image:
> >
> > fdtmap {
> > }:
> >
>
> Simon,
>
> Sorry I still don't quite understand:
>
> diff --git a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> index f200afac9f..c6d8932fa4 100644
> --- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> +++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> @@ -163,6 +163,9 @@
> itb {
> filename = "u-boot.itb";
>
> + fdtmap {
> + };
> +
> fit {
> description = "Configuration to load ATF before U-Boot";
> #address-cells = <1>;
>
>
> $ make imx8mm_evk_defconfig
> $ make
> $ ./tools/binman/binman ls -i u-boot.itb
> Name Image-pos Size Entry-type Offset Uncomp-size
> ------------------------------------------------------------------
> main-section 0 a3875 section 0
> fdtmap 0 48d fdtmap 0
> fit 48d a33e8 fit 48d
>
> For signing we need the loadaddr/offset/size of the components within
> the FIT image. Since binman is calling mkimage to create FIT images it
> seems outside the scope of binman to be able to dump details on the
> actual FIT image. Perhaps mkimage or another tool is to be used for
> that detail?
Yes, binman does not look inside FITs at presnt. You may want to look
at dump_image?
>
> > >
> > > I would very much like to understand how to use binman to get the
> > > various offsets needed for signing an IMX image for use with HAB.
> >
> > You should be able to add signing support to binman for your use case.
> > See for example how vblock.py works.
>
> I see... so your saying instead of using an external tool to generate
> a txt template with the offset/size values for the various blobs
> instead we need to implement for example a habv4.py to add a habv4
> entry and the python class would have access to the content handles to
> determine the addr/size in order to create the text template file fed
> to the NXP code signing tool?
Yes that should work. It is in fact what binman is designed for
(producing images, with all the signing, etc.)
Regards,
Simon
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-12 16:42 ` Tim Harvey
2021-07-12 19:43 ` Simon Glass
@ 2021-07-19 4:16 ` Heiko Schocher
1 sibling, 0 replies; 43+ messages in thread
From: Heiko Schocher @ 2021-07-19 4:16 UTC (permalink / raw)
To: Tim Harvey
Cc: Teresa Remmet, u-boot, Stefano Babic, Fabio Estevam,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki, Simon Glass
Hello Tim,
On 12.07.21 18:42, Tim Harvey wrote:
> On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
>>
>> Hello Tim,
>>
>> On 09.07.21 16:47, Tim Harvey wrote:
>>> On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
>>>>
>>>> Factor out the common node settings for dm-spl and dm-pre-reloc
>>>> and move them to imx8mp-u-boot.dtsi
>>>>
>>>> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
>>>> Reviewed-by: Fabio Estevam <festevam@gmail.com>
>>>> Reviewed-by: Heiko Schocher <hs@denx.de>
>>>> ---
>>>> Changes in v3:
>>>> - Moved binman nodes to common imx8mp-u-boot.dtsi
>>>> Changes in v2:
>>>> - none
>>>>
>>>> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
>>>> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
>>>> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
>>>> 3 files changed, 153 insertions(+), 178 deletions(-)
>>>> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
>>>>
> <snip>
>>>>
>>>
>>> Teresa,
>>>
>>> I've noticed many of the imx8m boards migrating to using binman for
>>> image packaging.
>>>
>>> Doesn't this change from having a single flash.bin encompasing the SPL
>>> and U-Boot proper to having split files? I noticed that happened with
>>> imx8mm_evk for example when it switched to binman.
>>
>> Yes, but you can easy generate there a single image again.
>>
>>> What are the benefits to using binman?
>>
>> Beside the pros from binmal in general, I see the benefit in special
>> for imx8mp, that you can get all infos you need for signing the image
>> from within the image. No need to save some log output from U-Boot
>> build and parse this output ...
>>
>
> (+cc Simon)
>
> Heiko,
>
> And what are the pros from binman in general? I've read over
> tools/binman/binman.rst so I'm assuming you mean what is described
> there as benefits.
Yes!
> How do you get all the details needed for signing the image from binman?
Not from binman directly, instead for getting the offset and length
of the images you want to sign, I simply used "fdtget" to read them
from the u-boot image:
(extract from my yocto class... WIP also):
dec2hex() {
echo 0x$(printf '%x' $1)
}
# $1 ... fit image name
# $2 ... part of fit image
fit_get_off() {
val=$(fdtget $1 /images/$2 data-position)
# dec -> hex
dec2hex $val
}
# $1 ... fit image name
# $2 ... part of fit image
fit_get_len() {
val=$(fdtget $1 /images/$2 data-size)
dec2hex $val
}
example for atf:
off=$(fit_get_off u-boot.itb atf)
len=$(fit_get_len u-boot.itb atf)
Hope this helps?
> If I make imx8mm_evk_defconfig which produces via binman flash.bin and
> u-boot.itb I get the following:
>
> $ ./tools/binman/binman ls -i flash.bin
> binman: Cannot find FDT map in image
> $ ./tools/binman/binman ls -i u-boot.itb
> binman: Cannot find FDT map in image
>
> I would very much like to understand how to use binman to get the
> various offsets needed for signing an IMX image for use with HAB.
>
> Thanks,
>
> Tim
>
bye,
Heiko
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs@denx.de
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-13 20:17 ` Simon Glass
@ 2021-07-19 4:18 ` Heiko Schocher
0 siblings, 0 replies; 43+ messages in thread
From: Heiko Schocher @ 2021-07-19 4:18 UTC (permalink / raw)
To: Simon Glass, Tim Harvey
Cc: Teresa Remmet, u-boot, Stefano Babic, Fabio Estevam,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Tim, Simon,
On 13.07.21 22:17, Simon Glass wrote:
> Hi Tim,
>
> On Mon, 12 Jul 2021 at 14:58, Tim Harvey <tharvey@gateworks.com> wrote:
>>
>> On Mon, Jul 12, 2021 at 12:44 PM Simon Glass <sjg@chromium.org> wrote:
>>>
>>> Hi Tim,
>>>
>>> On Mon, 12 Jul 2021 at 10:42, Tim Harvey <tharvey@gateworks.com> wrote:
>>>>
>>>> On Sat, Jul 10, 2021 at 5:23 AM Heiko Schocher <hs@denx.de> wrote:
>>>>>
>>>>> Hello Tim,
>>>>>
>>>>> On 09.07.21 16:47, Tim Harvey wrote:
>>>>>> On Wed, Jul 7, 2021 at 5:58 AM Teresa Remmet <t.remmet@phytec.de> wrote:
>>>>>>>
>>>>>>> Factor out the common node settings for dm-spl and dm-pre-reloc
>>>>>>> and move them to imx8mp-u-boot.dtsi
>>>>>>>
>>>>>>> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
>>>>>>> Reviewed-by: Fabio Estevam <festevam@gmail.com>
>>>>>>> Reviewed-by: Heiko Schocher <hs@denx.de>
>>>>>>> ---
>>>>>>> Changes in v3:
>>>>>>> - Moved binman nodes to common imx8mp-u-boot.dtsi
>>>>>>> Changes in v2:
>>>>>>> - none
>>>>>>>
>>>>>>> arch/arm/dts/imx8mp-evk-u-boot.dtsi | 143 +----------------
>>>>>>> .../imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 39 +----
>>>>>>> arch/arm/dts/imx8mp-u-boot.dtsi | 149 ++++++++++++++++++
>>>>>>> 3 files changed, 153 insertions(+), 178 deletions(-)
>>>>>>> create mode 100644 arch/arm/dts/imx8mp-u-boot.dtsi
>>>>>>>
>>>> <snip>
>>>>>>>
>>>>>>
>>>>>> Teresa,
>>>>>>
>>>>>> I've noticed many of the imx8m boards migrating to using binman for
>>>>>> image packaging.
>>>>>>
>>>>>> Doesn't this change from having a single flash.bin encompasing the SPL
>>>>>> and U-Boot proper to having split files? I noticed that happened with
>>>>>> imx8mm_evk for example when it switched to binman.
>>>>>
>>>>> Yes, but you can easy generate there a single image again.
>>>>>
>>>>>> What are the benefits to using binman?
>>>>>
>>>>> Beside the pros from binmal in general, I see the benefit in special
>>>>> for imx8mp, that you can get all infos you need for signing the image
>>>>> from within the image. No need to save some log output from U-Boot
>>>>> build and parse this output ...
>>>>>
>>>>
>>>> (+cc Simon)
>>>>
>>>> Heiko,
>>>>
>>>> And what are the pros from binman in general? I've read over
>>>> tools/binman/binman.rst so I'm assuming you mean what is described
>>>> there as benefits.
>>>>
>>>> How do you get all the details needed for signing the image from binman?
>>>>
>>>> If I make imx8mm_evk_defconfig which produces via binman flash.bin and
>>>> u-boot.itb I get the following:
>>>>
>>>> $ ./tools/binman/binman ls -i flash.bin
>>>> binman: Cannot find FDT map in image
>>>> $ ./tools/binman/binman ls -i u-boot.itb
>>>> binman: Cannot find FDT map in image
>>>
>>> As the message says, you need an 'fdtmap' in the image:
>>>
>>> fdtmap {
>>> }:
>>>
>>
>> Simon,
>>
>> Sorry I still don't quite understand:
>>
>> diff --git a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> index f200afac9f..c6d8932fa4 100644
>> --- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> +++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> @@ -163,6 +163,9 @@
>> itb {
>> filename = "u-boot.itb";
>>
>> + fdtmap {
>> + };
>> +
>> fit {
>> description = "Configuration to load ATF before U-Boot";
>> #address-cells = <1>;
>>
>>
>> $ make imx8mm_evk_defconfig
>> $ make
>> $ ./tools/binman/binman ls -i u-boot.itb
>> Name Image-pos Size Entry-type Offset Uncomp-size
>> ------------------------------------------------------------------
>> main-section 0 a3875 section 0
>> fdtmap 0 48d fdtmap 0
>> fit 48d a33e8 fit 48d
>>
>> For signing we need the loadaddr/offset/size of the components within
>> the FIT image. Since binman is calling mkimage to create FIT images it
>> seems outside the scope of binman to be able to dump details on the
>> actual FIT image. Perhaps mkimage or another tool is to be used for
>> that detail?
>
> Yes, binman does not look inside FITs at presnt. You may want to look
> at dump_image?
>
>>
>>>>
>>>> I would very much like to understand how to use binman to get the
>>>> various offsets needed for signing an IMX image for use with HAB.
>>>
>>> You should be able to add signing support to binman for your use case.
>>> See for example how vblock.py works.
>>
>> I see... so your saying instead of using an external tool to generate
>> a txt template with the offset/size values for the various blobs
>> instead we need to implement for example a habv4.py to add a habv4
>> entry and the python class would have access to the content handles to
>> determine the addr/size in order to create the text template file fed
>> to the NXP code signing tool?
>
> Yes that should work. It is in fact what binman is designed for
> (producing images, with all the signing, etc.)
Ah, sounds interesting!
@Tim: Do you have time to look into this topic?
bye,
Heiko
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs@denx.de
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-07-10 12:23 ` Heiko Schocher
2021-07-12 16:42 ` Tim Harvey
@ 2021-08-13 12:55 ` Fabio Estevam
2021-08-16 10:27 ` Heiko Schocher
1 sibling, 1 reply; 43+ messages in thread
From: Fabio Estevam @ 2021-08-13 12:55 UTC (permalink / raw)
To: Heiko Schocher
Cc: Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Heiko,
On Sat, Jul 10, 2021 at 9:23 AM Heiko Schocher <hs@denx.de> wrote:
> > Doesn't this change from having a single flash.bin encompasing the SPL
> > and U-Boot proper to having split files? I noticed that happened with
> > imx8mm_evk for example when it switched to binman.
>
> Yes, but you can easy generate there a single image again.
Yes, that would be preferable
Any suggestions on how we can have a single bootable image again?
Thanks,
Fabio Estevam
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-13 12:55 ` Fabio Estevam
@ 2021-08-16 10:27 ` Heiko Schocher
2021-08-16 13:56 ` Fabio Estevam
0 siblings, 1 reply; 43+ messages in thread
From: Heiko Schocher @ 2021-08-16 10:27 UTC (permalink / raw)
To: Fabio Estevam
Cc: Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hello Fabio,
On 13.08.21 14:55, Fabio Estevam wrote:
> Hi Heiko,
>
> On Sat, Jul 10, 2021 at 9:23 AM Heiko Schocher <hs@denx.de> wrote:
>
>>> Doesn't this change from having a single flash.bin encompasing the SPL
>>> and U-Boot proper to having split files? I noticed that happened with
>>> imx8mm_evk for example when it switched to binman.
>>
>> Yes, but you can easy generate there a single image again.
>
> Yes, that would be preferable
>
> Any suggestions on how we can have a single bootable image again?
I am not a binman expert, but may you try to add in your u-boot.dtsi
in your "binman" node at the end:
imx-boot {
filename = "imx-boot.bin";
pad-byte = <0x00>;
spl: blob-ext@1 {
offset = <0x0>;
filename = "flash.bin";
};
uboot: blob-ext@2 {
offset = <0x59000>;
filename = "u-boot.itb";
};
};
bye,
Heiko
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs@denx.de
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-16 10:27 ` Heiko Schocher
@ 2021-08-16 13:56 ` Fabio Estevam
2021-08-16 14:09 ` Frieder Schrempf
0 siblings, 1 reply; 43+ messages in thread
From: Fabio Estevam @ 2021-08-16 13:56 UTC (permalink / raw)
To: Heiko Schocher
Cc: Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Heiko,
On Mon, Aug 16, 2021 at 7:27 AM Heiko Schocher <hs@denx.de> wrote:
> I am not a binman expert, but may you try to add in your u-boot.dtsi
> in your "binman" node at the end:
>
> imx-boot {
> filename = "imx-boot.bin";
> pad-byte = <0x00>;
>
> spl: blob-ext@1 {
> offset = <0x0>;
> filename = "flash.bin";
> };
> uboot: blob-ext@2 {
> offset = <0x59000>;
> filename = "u-boot.itb";
> };
This helped!
I had to change the offset and now I can flash only flash.bin
and it boots fine:
--- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
@@ -217,4 +217,18 @@
};
};
};
+
+ imx-boot {
+ filename = "flash.bin";
+ pad-byte = <0x00>;
+
+ spl: blob-ext@1 {
+ offset = <0x0>;
+ filename = "flash.bin";
+ };
+ uboot: blob-ext@2 {
+ offset = <0x57c00>;
+ filename = "u-boot.itb";
+ };
+ };
};
I will submit the patch shortly.
Thanks
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-16 13:56 ` Fabio Estevam
@ 2021-08-16 14:09 ` Frieder Schrempf
2021-08-16 14:18 ` Frieder Schrempf
0 siblings, 1 reply; 43+ messages in thread
From: Frieder Schrempf @ 2021-08-16 14:09 UTC (permalink / raw)
To: Fabio Estevam, Heiko Schocher
Cc: Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Fabio,
On 16.08.21 15:56, Fabio Estevam wrote:
> Hi Heiko,
>
> On Mon, Aug 16, 2021 at 7:27 AM Heiko Schocher <hs@denx.de> wrote:
>
>> I am not a binman expert, but may you try to add in your u-boot.dtsi
>> in your "binman" node at the end:
>>
>> imx-boot {
>> filename = "imx-boot.bin";
>> pad-byte = <0x00>;
>>
>> spl: blob-ext@1 {
>> offset = <0x0>;
>> filename = "flash.bin";
>> };
>> uboot: blob-ext@2 {
>> offset = <0x59000>;
>> filename = "u-boot.itb";
>> };
>
> This helped!
>
> I had to change the offset and now I can flash only flash.bin
> and it boots fine:
>
> --- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> +++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
> @@ -217,4 +217,18 @@
> };
> };
> };
> +
> + imx-boot {
> + filename = "flash.bin";
> + pad-byte = <0x00>;
> +
> + spl: blob-ext@1 {
> + offset = <0x0>;
> + filename = "flash.bin";
> + };
> + uboot: blob-ext@2 {
> + offset = <0x57c00>;
> + filename = "u-boot.itb";
> + };
> + };
> };
>
> I will submit the patch shortly.
If you prepare a patch I would prefer to have separate names for the SPL image and the final concatenated image. So we don't overwrite the SPL image and can still use it on its own if needed.
But rather than choosing a new name for the complete image (as Heiko did above), I would like to rename the SPL image to something more meaningful like spl.bin first and then use flash.bin for the full image.
What do you think?
Thanks
Frieder
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-16 14:09 ` Frieder Schrempf
@ 2021-08-16 14:18 ` Frieder Schrempf
2021-08-16 15:10 ` Fabio Estevam
0 siblings, 1 reply; 43+ messages in thread
From: Frieder Schrempf @ 2021-08-16 14:18 UTC (permalink / raw)
To: Fabio Estevam, Heiko Schocher
Cc: Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
On 16.08.21 16:09, Frieder Schrempf wrote:
> Hi Fabio,
>
> On 16.08.21 15:56, Fabio Estevam wrote:
>> Hi Heiko,
>>
>> On Mon, Aug 16, 2021 at 7:27 AM Heiko Schocher <hs@denx.de> wrote:
>>
>>> I am not a binman expert, but may you try to add in your u-boot.dtsi
>>> in your "binman" node at the end:
>>>
>>> imx-boot {
>>> filename = "imx-boot.bin";
>>> pad-byte = <0x00>;
>>>
>>> spl: blob-ext@1 {
>>> offset = <0x0>;
>>> filename = "flash.bin";
>>> };
>>> uboot: blob-ext@2 {
>>> offset = <0x59000>;
>>> filename = "u-boot.itb";
>>> };
>>
>> This helped!
>>
>> I had to change the offset and now I can flash only flash.bin
>> and it boots fine:
>>
>> --- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> +++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
>> @@ -217,4 +217,18 @@
>> };
>> };
>> };
>> +
>> + imx-boot {
>> + filename = "flash.bin";
>> + pad-byte = <0x00>;
>> +
>> + spl: blob-ext@1 {
>> + offset = <0x0>;
>> + filename = "flash.bin";
>> + };
>> + uboot: blob-ext@2 {
>> + offset = <0x57c00>;
>> + filename = "u-boot.itb";
>> + };
>> + };
>> };
>>
>> I will submit the patch shortly.
>
> If you prepare a patch I would prefer to have separate names for the SPL image and the final concatenated image. So we don't overwrite the SPL image and can still use it on its own if needed.
> But rather than choosing a new name for the complete image (as Heiko did above), I would like to rename the SPL image to something more meaningful like spl.bin first and then use flash.bin for the full image.
> What do you think?
And it would also be nice if we could share the common parts of the binman config between the different boards to avoid having this in each boards dtsi and to avoid having diverging configurations, where e. g. flash.bin refers to different kinds of images.
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-16 14:18 ` Frieder Schrempf
@ 2021-08-16 15:10 ` Fabio Estevam
2021-08-18 8:17 ` Marcel Ziswiler
0 siblings, 1 reply; 43+ messages in thread
From: Fabio Estevam @ 2021-08-16 15:10 UTC (permalink / raw)
To: Frieder Schrempf
Cc: Heiko Schocher, Tim Harvey, Teresa Remmet, u-boot, Stefano Babic,
NXP i . MX U-Boot Team, Peng Fan, Jagan Teki
Hi Frieder,
On Mon, Aug 16, 2021 at 11:18 AM Frieder Schrempf
<frieder.schrempf@kontron.de> wrote:
> > If you prepare a patch I would prefer to have separate names for the SPL image and the final concatenated image. So we don't overwrite the SPL image and can still use it on its own if needed.
> > But rather than choosing a new name for the complete image (as Heiko did above), I would like to rename the SPL image to something more meaningful like spl.bin first and then use flash.bin for the full image.
> > What do you think?
It seems we cannot rename the SPL to spl.bin as this would cause
breakage to i.MX8MM boards that do not use binman, such as
verdin-imx8mm_defconfig.
> And it would also be nice if we could share the common parts of the binman config between the different boards to avoid having this in each boards dtsi and to avoid having diverging configurations, where e. g. flash.bin refers to different kinds of images.
Agreed.
Let me try to send a proposal for imx8mm-evk first. If it gets
accepted, then I can try to make a common approach.
Regards,
Fabio Estevam
^ permalink raw reply [flat|nested] 43+ messages in thread
* Re: [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi
2021-08-16 15:10 ` Fabio Estevam
@ 2021-08-18 8:17 ` Marcel Ziswiler
0 siblings, 0 replies; 43+ messages in thread
From: Marcel Ziswiler @ 2021-08-18 8:17 UTC (permalink / raw)
To: festevam, frieder.schrempf
Cc: uboot-imx, hs, peng.fan, sbabic, jagan, tharvey, u-boot, t.remmet
Hi Fabio and Frieder
On Mon, 2021-08-16 at 12:10 -0300, Fabio Estevam wrote:
> Hi Frieder,
>
> On Mon, Aug 16, 2021 at 11:18 AM Frieder Schrempf
> <frieder.schrempf@kontron.de> wrote:
>
> > > If you prepare a patch I would prefer to have separate names for the SPL image and the final concatenated
> > > image. So we don't overwrite the SPL image and can still use it on its own if needed.
> > > But rather than choosing a new name for the complete image (as Heiko did above), I would like to rename
> > > the SPL image to something more meaningful like spl.bin first and then use flash.bin for the full image.
> > > What do you think?
>
> It seems we cannot rename the SPL to spl.bin as this would cause
> breakage to i.MX8MM boards that do not use binman, such as
> verdin-imx8mm_defconfig.
I am actually just about to send our conversion to using binman for this as well (;-p).
> > And it would also be nice if we could share the common parts of the binman config between the different
> > boards to avoid having this in each boards dtsi and to avoid having diverging configurations, where e. g.
> > flash.bin refers to different kinds of images.
>
> Agreed.
I am also all in for this idea. Should I still be sending my patch set converting Verdin iMX8M Mini separately
first? Maybe that would be the easiest and we could then transition them all to a common approach, not?
> Let me try to send a proposal for imx8mm-evk first. If it gets
> accepted, then I can try to make a common approach.
Yes, that's kinda what I was thinking. Thanks!
> Regards,
>
> Fabio Estevam
Cheers
Marcel
^ permalink raw reply [flat|nested] 43+ messages in thread
end of thread, other threads:[~2021-08-18 8:18 UTC | newest]
Thread overview: 43+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-07 12:57 [PATCH v3 0/9] phyCORE-i.MX8MP Update Teresa Remmet
2021-07-07 12:57 ` [PATCH v3 1/9] arm: dts: imx8mp: Resync imx8mp device tree include Teresa Remmet
2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:57 ` [PATCH v3 2/9] arm: dts: imx8mp: Add common u-boot dtsi Teresa Remmet
2021-07-09 14:47 ` Tim Harvey
2021-07-10 12:23 ` Heiko Schocher
2021-07-12 16:42 ` Tim Harvey
2021-07-12 19:43 ` Simon Glass
2021-07-12 20:58 ` Tim Harvey
2021-07-13 20:17 ` Simon Glass
2021-07-19 4:18 ` Heiko Schocher
2021-07-19 4:16 ` Heiko Schocher
2021-08-13 12:55 ` Fabio Estevam
2021-08-16 10:27 ` Heiko Schocher
2021-08-16 13:56 ` Fabio Estevam
2021-08-16 14:09 ` Frieder Schrempf
2021-08-16 14:18 ` Frieder Schrempf
2021-08-16 15:10 ` Fabio Estevam
2021-08-18 8:17 ` Marcel Ziswiler
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:57 ` [PATCH v3 3/9] arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel Teresa Remmet
2021-07-10 15:52 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:57 ` [PATCH v3 4/9] board: phytec: phycore_imx8mp: Change debug UART Teresa Remmet
2021-07-10 15:54 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 5/9] board: phytec: phycore_imx8mp: Add fec support Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 6/9] board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:35 ` sbabic
2021-07-07 12:58 ` [PATCH v3 7/9] board: phytec: phycore-imx8mp: Enable DVS1 control Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 8/9] arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
2021-07-07 12:58 ` [PATCH v3 9/9] board: phytec: imx8mp-phycore: Switch to binman Teresa Remmet
2021-07-10 15:53 ` sbabic
2021-07-10 19:36 ` sbabic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.