* [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-28 3:54 ` djw
0 siblings, 0 replies; 27+ messages in thread
From: djw @ 2021-06-28 3:54 UTC (permalink / raw)
To: linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Levin Du, Heiko Stuebner, Chen-Yu Tsai,
Jagan Teki, Jensen Huang, Johan Jonker, Liang Chen, Marty Jones,
Rob Herring, Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
From: Levin Du <djw@t-chip.com.cn>
ROC-RK3399-PC-PLUS is the board inside the portable Firefly Station P1 Geek
PC. As a redesign after the ROC-RK3399-PC, it uses DC-12V as power input
and spares a USB 3 host port. It is also equipped with a USB WiFi chip and
audio codec without the mezzanine board.
- Rockchip RK3399 SoC
- 4GB LPDDR4 RAM
- 16MB SPI-Flash
- eMMC slot
- TF card slot
- USB 3.0 Port x 1, USB 2.0 Port x 1, TypeC Port x 1
- HDMI
- Gigabit Ethernet
- WiFi: RTL8723DU
- Audio: ES8388
- Key: Recovery
- LED: WORK, DIY
- IR
Signed-off-by: Kongxin Deng <dkx@t-chip.com.cn>
Signed-off-by: Levin Du <djw@t-chip.com.cn>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-roc-pc-plus.dts | 223 ++++++++++++++++++
2 files changed, 224 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7fdb41de01ec..d6ab171b2522 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-plus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4b.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
new file mode 100644
index 000000000000..370e8bf1b40c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
@@ -0,1 +1,223 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3399-roc-pc.dtsi"
+
+/**
+ * Notice:
+ * 1. rk3399-roc-pc-plus is powered by dc_12v directly.
+ * 2. rk3399-roc-pc-plus has only vcc_bus_typec0 in schematic, which is coresponding
+ * to vcc_vbus_typec1 in rk3399-roc-pc.
+ * For simplicity, reserve the node name of vcc_vbus_typec1.
+ * 3. vcc5v0_host is actually 2 regulators (host0, 1) controlled by the same gpio.
+ */
+
+/delete-node/ &fusb1;
+/delete-node/ &hub_rst;
+/delete-node/ &mp8859;
+/delete-node/ &vcc_sys_en;
+/delete-node/ &vcc_vbus_typec0;
+/delete-node/ &yellow_led;
+
+/ {
+ model = "Firefly ROC-RK3399-PC-PLUS Board";
+ compatible = "firefly,roc-rk3399-pc-plus", "rockchip,rk3399";
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ gpio-fan {
+ #cooling-cells = <2>;
+ compatible = "gpio-fan";
+ gpio-fan,speed-map = <0 0 3000 1>;
+ gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ /delete-node/ gpio-keys;
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_pin>, <&diy_led_pin>;
+ };
+
+ es8388-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det_pin>;
+ simple-audio-card,name = "rockchip,es8388-codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones";
+ simple-audio-card,routing =
+ "LINPUT1", "Mic Jack",
+ "Headphone Amp INL", "LOUT2",
+ "Headphone Amp INR", "ROUT2",
+ "Headphones", "Headphone Amp OUTL",
+ "Headphones", "Headphone Amp OUTR";
+
+ simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,aux-devs = <&headphones_amp>;
+ simple-audio-card,pin-switches = "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ };
+ };
+
+ /* not amplifier, used as switcher only */
+ headphones_amp: headphones-amp {
+ compatible = "simple-audio-amplifier";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ear_ctl_pin>;
+ enable-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ sound-name-prefix = "Headphone Amp";
+ VCC-supply = <&vcca3v0_codec>;
+ };
+
+ ir-receiver {
+ linux,rc-map-name = "rc-khadas";
+ };
+
+};
+
+&fusb0 {
+ vbus-supply = <&vcc_vbus_typec1>;
+};
+
+&i2c0 {
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hym8563_int>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA5 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&i2c1 {
+ es8388: es8388@11 {
+ compatible = "everest,es8388";
+ reg = <0x11>;
+ clock-names = "mclk";
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ #sound-dai-cells = <0>;
+ status = "okay";
+ };
+};
+
+// <4 RK_PA0 1 &pcfg_pull_none> is used as i2s_8ch_mclk_pin
+&i2s0_8ch_bus {
+ rockchip,pins =
+ <3 RK_PD0 1 &pcfg_pull_none>,
+ <3 RK_PD1 1 &pcfg_pull_none>,
+ <3 RK_PD2 1 &pcfg_pull_none>,
+ <3 RK_PD3 1 &pcfg_pull_none>,
+ <3 RK_PD4 1 &pcfg_pull_none>,
+ <3 RK_PD5 1 &pcfg_pull_none>,
+ <3 RK_PD6 1 &pcfg_pull_none>,
+ <3 RK_PD7 1 &pcfg_pull_none>;
+};
+
+&i2s1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s_8ch_mclk_pin>, <&i2s1_2ch_bus>;
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
+ status = "okay";
+};
+
+&pinctrl {
+ es8388 {
+ ear_ctl_pin: ear-ctl-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+
+ hp_det_pin: hp-det-pin {
+ rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ hym8563 {
+ hym8563_int: hym8563-int {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ i2s1 {
+ i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
+ rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
+ };
+ };
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ phy-supply = <&vcc_vbus_typec1>;
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vcc_sys {
+ // vcc_sys is fixed, not controlled by any gpio
+ /delete-property/ gpio;
+ /delete-property/ pinctrl-names;
+ /delete-property/ pinctrl-0;
+};
+
+&vcc5v0_host {
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+};
--
2.23.0.37.g745f6812895b
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 27+ messages in thread* [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-28 3:54 ` djw
0 siblings, 0 replies; 27+ messages in thread
From: djw @ 2021-06-28 3:54 UTC (permalink / raw)
To: linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Levin Du, Heiko Stuebner, Chen-Yu Tsai,
Jagan Teki, Jensen Huang, Johan Jonker, Liang Chen, Marty Jones,
Rob Herring, Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
From: Levin Du <djw@t-chip.com.cn>
ROC-RK3399-PC-PLUS is the board inside the portable Firefly Station P1 Geek
PC. As a redesign after the ROC-RK3399-PC, it uses DC-12V as power input
and spares a USB 3 host port. It is also equipped with a USB WiFi chip and
audio codec without the mezzanine board.
- Rockchip RK3399 SoC
- 4GB LPDDR4 RAM
- 16MB SPI-Flash
- eMMC slot
- TF card slot
- USB 3.0 Port x 1, USB 2.0 Port x 1, TypeC Port x 1
- HDMI
- Gigabit Ethernet
- WiFi: RTL8723DU
- Audio: ES8388
- Key: Recovery
- LED: WORK, DIY
- IR
Signed-off-by: Kongxin Deng <dkx@t-chip.com.cn>
Signed-off-by: Levin Du <djw@t-chip.com.cn>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-roc-pc-plus.dts | 223 ++++++++++++++++++
2 files changed, 224 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7fdb41de01ec..d6ab171b2522 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-plus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4b.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
new file mode 100644
index 000000000000..370e8bf1b40c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
@@ -0,1 +1,223 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3399-roc-pc.dtsi"
+
+/**
+ * Notice:
+ * 1. rk3399-roc-pc-plus is powered by dc_12v directly.
+ * 2. rk3399-roc-pc-plus has only vcc_bus_typec0 in schematic, which is coresponding
+ * to vcc_vbus_typec1 in rk3399-roc-pc.
+ * For simplicity, reserve the node name of vcc_vbus_typec1.
+ * 3. vcc5v0_host is actually 2 regulators (host0, 1) controlled by the same gpio.
+ */
+
+/delete-node/ &fusb1;
+/delete-node/ &hub_rst;
+/delete-node/ &mp8859;
+/delete-node/ &vcc_sys_en;
+/delete-node/ &vcc_vbus_typec0;
+/delete-node/ &yellow_led;
+
+/ {
+ model = "Firefly ROC-RK3399-PC-PLUS Board";
+ compatible = "firefly,roc-rk3399-pc-plus", "rockchip,rk3399";
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ gpio-fan {
+ #cooling-cells = <2>;
+ compatible = "gpio-fan";
+ gpio-fan,speed-map = <0 0 3000 1>;
+ gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ /delete-node/ gpio-keys;
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_pin>, <&diy_led_pin>;
+ };
+
+ es8388-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det_pin>;
+ simple-audio-card,name = "rockchip,es8388-codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones";
+ simple-audio-card,routing =
+ "LINPUT1", "Mic Jack",
+ "Headphone Amp INL", "LOUT2",
+ "Headphone Amp INR", "ROUT2",
+ "Headphones", "Headphone Amp OUTL",
+ "Headphones", "Headphone Amp OUTR";
+
+ simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,aux-devs = <&headphones_amp>;
+ simple-audio-card,pin-switches = "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ };
+ };
+
+ /* not amplifier, used as switcher only */
+ headphones_amp: headphones-amp {
+ compatible = "simple-audio-amplifier";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ear_ctl_pin>;
+ enable-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ sound-name-prefix = "Headphone Amp";
+ VCC-supply = <&vcca3v0_codec>;
+ };
+
+ ir-receiver {
+ linux,rc-map-name = "rc-khadas";
+ };
+
+};
+
+&fusb0 {
+ vbus-supply = <&vcc_vbus_typec1>;
+};
+
+&i2c0 {
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hym8563_int>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA5 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&i2c1 {
+ es8388: es8388@11 {
+ compatible = "everest,es8388";
+ reg = <0x11>;
+ clock-names = "mclk";
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ #sound-dai-cells = <0>;
+ status = "okay";
+ };
+};
+
+// <4 RK_PA0 1 &pcfg_pull_none> is used as i2s_8ch_mclk_pin
+&i2s0_8ch_bus {
+ rockchip,pins =
+ <3 RK_PD0 1 &pcfg_pull_none>,
+ <3 RK_PD1 1 &pcfg_pull_none>,
+ <3 RK_PD2 1 &pcfg_pull_none>,
+ <3 RK_PD3 1 &pcfg_pull_none>,
+ <3 RK_PD4 1 &pcfg_pull_none>,
+ <3 RK_PD5 1 &pcfg_pull_none>,
+ <3 RK_PD6 1 &pcfg_pull_none>,
+ <3 RK_PD7 1 &pcfg_pull_none>;
+};
+
+&i2s1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s_8ch_mclk_pin>, <&i2s1_2ch_bus>;
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
+ status = "okay";
+};
+
+&pinctrl {
+ es8388 {
+ ear_ctl_pin: ear-ctl-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+
+ hp_det_pin: hp-det-pin {
+ rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ hym8563 {
+ hym8563_int: hym8563-int {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ i2s1 {
+ i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
+ rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
+ };
+ };
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ phy-supply = <&vcc_vbus_typec1>;
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vcc_sys {
+ // vcc_sys is fixed, not controlled by any gpio
+ /delete-property/ gpio;
+ /delete-property/ pinctrl-names;
+ /delete-property/ pinctrl-0;
+};
+
+&vcc5v0_host {
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+};
--
2.23.0.37.g745f6812895b
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
2021-06-28 3:54 ` djw
(?)
@ 2021-06-29 9:15 ` Levin
-1 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-29 9:15 UTC (permalink / raw)
To: linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Heiko Stuebner, Chen-Yu Tsai,
Jagan Teki, Jensen Huang, Johan Jonker, Liang Chen, Marty Jones,
Rob Herring, Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi all, is it possible to turn on some codec mixer switch in the device
tree?
Currently, to hear to sound, we need to run the following commands from
the user space:
# turn on mixer switch
amixer -c 1 sset 'Left Mixer' on
amixer -c 1 sset 'Right Mixer' on
# raise volume
amixer -c 1 sset 'Output 2' 36
If these settings can be embedded into device tree, and set by kernel as
initial ALSA path settings,
user can hear the sound with zero ALSA config. That'll be great.
On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> +
> + es8388-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_pin>;
> + simple-audio-card,name = "rockchip,es8388-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones";
> + simple-audio-card,routing =
> + "LINPUT1", "Mic Jack",
> + "Headphone Amp INL", "LOUT2",
> + "Headphone Amp INR", "ROUT2",
> + "Headphones", "Headphone Amp OUTL",
> + "Headphones", "Headphone Amp OUTR";
> +
> + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,aux-devs = <&headphones_amp>;
> + simple-audio-card,pin-switches = "Headphones";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&es8388>;
> + };
> + };
> +
>
--
Best Regards!
Levin Du
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:15 ` Levin
0 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-29 9:15 UTC (permalink / raw)
To: linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Heiko Stuebner, Chen-Yu Tsai,
Jagan Teki, Jensen Huang, Johan Jonker, Liang Chen, Marty Jones,
Rob Herring, Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi all, is it possible to turn on some codec mixer switch in the device
tree?
Currently, to hear to sound, we need to run the following commands from
the user space:
# turn on mixer switch
amixer -c 1 sset 'Left Mixer' on
amixer -c 1 sset 'Right Mixer' on
# raise volume
amixer -c 1 sset 'Output 2' 36
If these settings can be embedded into device tree, and set by kernel as
initial ALSA path settings,
user can hear the sound with zero ALSA config. That'll be great.
On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> +
> + es8388-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_pin>;
> + simple-audio-card,name = "rockchip,es8388-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones";
> + simple-audio-card,routing =
> + "LINPUT1", "Mic Jack",
> + "Headphone Amp INL", "LOUT2",
> + "Headphone Amp INR", "ROUT2",
> + "Headphones", "Headphone Amp OUTL",
> + "Headphones", "Headphone Amp OUTR";
> +
> + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,aux-devs = <&headphones_amp>;
> + simple-audio-card,pin-switches = "Headphones";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&es8388>;
> + };
> + };
> +
>
--
Best Regards!
Levin Du
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:15 ` Levin
0 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-29 9:15 UTC (permalink / raw)
To: linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Heiko Stuebner, Chen-Yu Tsai,
Jagan Teki, Jensen Huang, Johan Jonker, Liang Chen, Marty Jones,
Rob Herring, Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi all, is it possible to turn on some codec mixer switch in the device
tree?
Currently, to hear to sound, we need to run the following commands from
the user space:
# turn on mixer switch
amixer -c 1 sset 'Left Mixer' on
amixer -c 1 sset 'Right Mixer' on
# raise volume
amixer -c 1 sset 'Output 2' 36
If these settings can be embedded into device tree, and set by kernel as
initial ALSA path settings,
user can hear the sound with zero ALSA config. That'll be great.
On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> +
> + es8388-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_pin>;
> + simple-audio-card,name = "rockchip,es8388-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones";
> + simple-audio-card,routing =
> + "LINPUT1", "Mic Jack",
> + "Headphone Amp INL", "LOUT2",
> + "Headphone Amp INR", "ROUT2",
> + "Headphones", "Headphone Amp OUTL",
> + "Headphones", "Headphone Amp OUTR";
> +
> + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,aux-devs = <&headphones_amp>;
> + simple-audio-card,pin-switches = "Headphones";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&es8388>;
> + };
> + };
> +
>
--
Best Regards!
Levin Du
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
2021-06-29 9:15 ` Levin
(?)
@ 2021-06-29 9:30 ` Heiko Stübner
-1 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:30 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Levin,
Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> Hi all, is it possible to turn on some codec mixer switch in the device
> tree?
I don't think that is appropriate and/or/ possible in the devicetree.
Instead I think you want an Alsa UCM profile for it, see:
https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
Heiko
>
>
> Currently, to hear to sound, we need to run the following commands from
> the user space:
>
> # turn on mixer switch
>
> amixer -c 1 sset 'Left Mixer' on
> amixer -c 1 sset 'Right Mixer' on
>
> # raise volume
>
> amixer -c 1 sset 'Output 2' 36
>
>
> If these settings can be embedded into device tree, and set by kernel as
> initial ALSA path settings,
>
> user can hear the sound with zero ALSA config. That'll be great.
>
>
> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > +
> > + es8388-sound {
> > + compatible = "simple-audio-card";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hp_det_pin>;
> > + simple-audio-card,name = "rockchip,es8388-codec";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,mclk-fs = <256>;
> > +
> > + simple-audio-card,widgets =
> > + "Microphone", "Mic Jack",
> > + "Headphone", "Headphones";
> > + simple-audio-card,routing =
> > + "LINPUT1", "Mic Jack",
> > + "Headphone Amp INL", "LOUT2",
> > + "Headphone Amp INR", "ROUT2",
> > + "Headphones", "Headphone Amp OUTL",
> > + "Headphones", "Headphone Amp OUTR";
> > +
> > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > + simple-audio-card,aux-devs = <&headphones_amp>;
> > + simple-audio-card,pin-switches = "Headphones";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&i2s1>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&es8388>;
> > + };
> > + };
> > +
> >
>
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:30 ` Heiko Stübner
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:30 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Levin,
Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> Hi all, is it possible to turn on some codec mixer switch in the device
> tree?
I don't think that is appropriate and/or/ possible in the devicetree.
Instead I think you want an Alsa UCM profile for it, see:
https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
Heiko
>
>
> Currently, to hear to sound, we need to run the following commands from
> the user space:
>
> # turn on mixer switch
>
> amixer -c 1 sset 'Left Mixer' on
> amixer -c 1 sset 'Right Mixer' on
>
> # raise volume
>
> amixer -c 1 sset 'Output 2' 36
>
>
> If these settings can be embedded into device tree, and set by kernel as
> initial ALSA path settings,
>
> user can hear the sound with zero ALSA config. That'll be great.
>
>
> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > +
> > + es8388-sound {
> > + compatible = "simple-audio-card";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hp_det_pin>;
> > + simple-audio-card,name = "rockchip,es8388-codec";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,mclk-fs = <256>;
> > +
> > + simple-audio-card,widgets =
> > + "Microphone", "Mic Jack",
> > + "Headphone", "Headphones";
> > + simple-audio-card,routing =
> > + "LINPUT1", "Mic Jack",
> > + "Headphone Amp INL", "LOUT2",
> > + "Headphone Amp INR", "ROUT2",
> > + "Headphones", "Headphone Amp OUTL",
> > + "Headphones", "Headphone Amp OUTR";
> > +
> > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > + simple-audio-card,aux-devs = <&headphones_amp>;
> > + simple-audio-card,pin-switches = "Headphones";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&i2s1>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&es8388>;
> > + };
> > + };
> > +
> >
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:30 ` Heiko Stübner
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:30 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Levin,
Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> Hi all, is it possible to turn on some codec mixer switch in the device
> tree?
I don't think that is appropriate and/or/ possible in the devicetree.
Instead I think you want an Alsa UCM profile for it, see:
https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
Heiko
>
>
> Currently, to hear to sound, we need to run the following commands from
> the user space:
>
> # turn on mixer switch
>
> amixer -c 1 sset 'Left Mixer' on
> amixer -c 1 sset 'Right Mixer' on
>
> # raise volume
>
> amixer -c 1 sset 'Output 2' 36
>
>
> If these settings can be embedded into device tree, and set by kernel as
> initial ALSA path settings,
>
> user can hear the sound with zero ALSA config. That'll be great.
>
>
> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > +
> > + es8388-sound {
> > + compatible = "simple-audio-card";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hp_det_pin>;
> > + simple-audio-card,name = "rockchip,es8388-codec";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,mclk-fs = <256>;
> > +
> > + simple-audio-card,widgets =
> > + "Microphone", "Mic Jack",
> > + "Headphone", "Headphones";
> > + simple-audio-card,routing =
> > + "LINPUT1", "Mic Jack",
> > + "Headphone Amp INL", "LOUT2",
> > + "Headphone Amp INR", "ROUT2",
> > + "Headphones", "Headphone Amp OUTL",
> > + "Headphones", "Headphone Amp OUTR";
> > +
> > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > + simple-audio-card,aux-devs = <&headphones_amp>;
> > + simple-audio-card,pin-switches = "Headphones";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&i2s1>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&es8388>;
> > + };
> > + };
> > +
> >
>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
2021-06-29 9:30 ` Heiko Stübner
(?)
@ 2021-06-29 9:32 ` Heiko Stübner
-1 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:32 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
> Hi Levin,
>
> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> > Hi all, is it possible to turn on some codec mixer switch in the device
> > tree?
>
> I don't think that is appropriate and/or/ possible in the devicetree.
>
> Instead I think you want an Alsa UCM profile for it, see:
> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>
>
> Heiko
>
> >
> >
> > Currently, to hear to sound, we need to run the following commands from
> > the user space:
> >
> > # turn on mixer switch
> >
> > amixer -c 1 sset 'Left Mixer' on
> > amixer -c 1 sset 'Right Mixer' on
> >
> > # raise volume
> >
> > amixer -c 1 sset 'Output 2' 36
> >
> >
> > If these settings can be embedded into device tree, and set by kernel as
> > initial ALSA path settings,
> >
> > user can hear the sound with zero ALSA config. That'll be great.
> >
> >
> > On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > > +
> > > + es8388-sound {
> > > + compatible = "simple-audio-card";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&hp_det_pin>;
> > > + simple-audio-card,name = "rockchip,es8388-codec";
and I guess you'd want a more specific name as that config likely is board-specific
not for all boards using the es8388-codec?
Heiko
> > > + simple-audio-card,format = "i2s";
> > > + simple-audio-card,mclk-fs = <256>;
> > > +
> > > + simple-audio-card,widgets =
> > > + "Microphone", "Mic Jack",
> > > + "Headphone", "Headphones";
> > > + simple-audio-card,routing =
> > > + "LINPUT1", "Mic Jack",
> > > + "Headphone Amp INL", "LOUT2",
> > > + "Headphone Amp INR", "ROUT2",
> > > + "Headphones", "Headphone Amp OUTL",
> > > + "Headphones", "Headphone Amp OUTR";
> > > +
> > > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > > + simple-audio-card,aux-devs = <&headphones_amp>;
> > > + simple-audio-card,pin-switches = "Headphones";
> > > +
> > > + simple-audio-card,cpu {
> > > + sound-dai = <&i2s1>;
> > > + };
> > > +
> > > + simple-audio-card,codec {
> > > + sound-dai = <&es8388>;
> > > + };
> > > + };
> > > +
> > >
> >
>
>
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:32 ` Heiko Stübner
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:32 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
> Hi Levin,
>
> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> > Hi all, is it possible to turn on some codec mixer switch in the device
> > tree?
>
> I don't think that is appropriate and/or/ possible in the devicetree.
>
> Instead I think you want an Alsa UCM profile for it, see:
> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>
>
> Heiko
>
> >
> >
> > Currently, to hear to sound, we need to run the following commands from
> > the user space:
> >
> > # turn on mixer switch
> >
> > amixer -c 1 sset 'Left Mixer' on
> > amixer -c 1 sset 'Right Mixer' on
> >
> > # raise volume
> >
> > amixer -c 1 sset 'Output 2' 36
> >
> >
> > If these settings can be embedded into device tree, and set by kernel as
> > initial ALSA path settings,
> >
> > user can hear the sound with zero ALSA config. That'll be great.
> >
> >
> > On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > > +
> > > + es8388-sound {
> > > + compatible = "simple-audio-card";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&hp_det_pin>;
> > > + simple-audio-card,name = "rockchip,es8388-codec";
and I guess you'd want a more specific name as that config likely is board-specific
not for all boards using the es8388-codec?
Heiko
> > > + simple-audio-card,format = "i2s";
> > > + simple-audio-card,mclk-fs = <256>;
> > > +
> > > + simple-audio-card,widgets =
> > > + "Microphone", "Mic Jack",
> > > + "Headphone", "Headphones";
> > > + simple-audio-card,routing =
> > > + "LINPUT1", "Mic Jack",
> > > + "Headphone Amp INL", "LOUT2",
> > > + "Headphone Amp INR", "ROUT2",
> > > + "Headphones", "Headphone Amp OUTL",
> > > + "Headphones", "Headphone Amp OUTR";
> > > +
> > > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > > + simple-audio-card,aux-devs = <&headphones_amp>;
> > > + simple-audio-card,pin-switches = "Headphones";
> > > +
> > > + simple-audio-card,cpu {
> > > + sound-dai = <&i2s1>;
> > > + };
> > > +
> > > + simple-audio-card,codec {
> > > + sound-dai = <&es8388>;
> > > + };
> > > + };
> > > +
> > >
> >
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-29 9:32 ` Heiko Stübner
0 siblings, 0 replies; 27+ messages in thread
From: Heiko Stübner @ 2021-06-29 9:32 UTC (permalink / raw)
To: linux-rockchip, Levin
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
> Hi Levin,
>
> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
> > Hi all, is it possible to turn on some codec mixer switch in the device
> > tree?
>
> I don't think that is appropriate and/or/ possible in the devicetree.
>
> Instead I think you want an Alsa UCM profile for it, see:
> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>
>
> Heiko
>
> >
> >
> > Currently, to hear to sound, we need to run the following commands from
> > the user space:
> >
> > # turn on mixer switch
> >
> > amixer -c 1 sset 'Left Mixer' on
> > amixer -c 1 sset 'Right Mixer' on
> >
> > # raise volume
> >
> > amixer -c 1 sset 'Output 2' 36
> >
> >
> > If these settings can be embedded into device tree, and set by kernel as
> > initial ALSA path settings,
> >
> > user can hear the sound with zero ALSA config. That'll be great.
> >
> >
> > On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
> > > +
> > > + es8388-sound {
> > > + compatible = "simple-audio-card";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&hp_det_pin>;
> > > + simple-audio-card,name = "rockchip,es8388-codec";
and I guess you'd want a more specific name as that config likely is board-specific
not for all boards using the es8388-codec?
Heiko
> > > + simple-audio-card,format = "i2s";
> > > + simple-audio-card,mclk-fs = <256>;
> > > +
> > > + simple-audio-card,widgets =
> > > + "Microphone", "Mic Jack",
> > > + "Headphone", "Headphones";
> > > + simple-audio-card,routing =
> > > + "LINPUT1", "Mic Jack",
> > > + "Headphone Amp INL", "LOUT2",
> > > + "Headphone Amp INR", "ROUT2",
> > > + "Headphones", "Headphone Amp OUTL",
> > > + "Headphones", "Headphone Amp OUTR";
> > > +
> > > + simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
> > > + simple-audio-card,aux-devs = <&headphones_amp>;
> > > + simple-audio-card,pin-switches = "Headphones";
> > > +
> > > + simple-audio-card,cpu {
> > > + sound-dai = <&i2s1>;
> > > + };
> > > +
> > > + simple-audio-card,codec {
> > > + sound-dai = <&es8388>;
> > > + };
> > > + };
> > > +
> > >
> >
>
>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
2021-06-29 9:32 ` Heiko Stübner
(?)
@ 2021-06-30 6:49 ` Levin
-1 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-30 6:49 UTC (permalink / raw)
To: Heiko Stübner, linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Heiko,
Thanks for your reply.
On 2021-06-29 5:32 PM, Heiko Stübner wrote:
> Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
>> Hi Levin,
>>
>> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
>>> Hi all, is it possible to turn on some codec mixer switch in the device
>>> tree?
>> I don't think that is appropriate and/or/ possible in the devicetree.
>>
>> Instead I think you want an Alsa UCM profile for it, see:
>> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>>
Alsa UCM profile is a complete solution, yet it requires more labor work
of adding a complex profile with all the controls.
The problem is, music/video player knows nothing of the mixers. And with
currently codec driver setting, user cannot
hear any sound until he turns on two mixer switch.
I hope to have a "simple-audio-card,switch" property here.
>>>
>>> Currently, to hear to sound, we need to run the following commands from
>>> the user space:
>>>
>>> # turn on mixer switch
>>>
>>> amixer -c 1 sset 'Left Mixer' on
>>> amixer -c 1 sset 'Right Mixer' on
>>>
>>> # raise volume
>>>
>>> amixer -c 1 sset 'Output 2' 36
>>>
>>>
>>> If these settings can be embedded into device tree, and set by kernel as
>>> initial ALSA path settings,
>>>
>>> user can hear the sound with zero ALSA config. That'll be great.
>>>
>>>
>>> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
>>>> +
>>>> + es8388-sound {
>>>> + compatible = "simple-audio-card";
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&hp_det_pin>;
>>>> + simple-audio-card,name = "rockchip,es8388-codec";
> and I guess you'd want a more specific name as that config likely is board-specific
> not for all boards using the es8388-codec?
>
>
> Heiko
>
I got what you mean now. It should be renamed to a board-specific card
name if using Alsa UCM profile, right ?
--
Best Regards!
Levin Du
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-30 6:49 ` Levin
0 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-30 6:49 UTC (permalink / raw)
To: Heiko Stübner, linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Heiko,
Thanks for your reply.
On 2021-06-29 5:32 PM, Heiko Stübner wrote:
> Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
>> Hi Levin,
>>
>> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
>>> Hi all, is it possible to turn on some codec mixer switch in the device
>>> tree?
>> I don't think that is appropriate and/or/ possible in the devicetree.
>>
>> Instead I think you want an Alsa UCM profile for it, see:
>> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>>
Alsa UCM profile is a complete solution, yet it requires more labor work
of adding a complex profile with all the controls.
The problem is, music/video player knows nothing of the mixers. And with
currently codec driver setting, user cannot
hear any sound until he turns on two mixer switch.
I hope to have a "simple-audio-card,switch" property here.
>>>
>>> Currently, to hear to sound, we need to run the following commands from
>>> the user space:
>>>
>>> # turn on mixer switch
>>>
>>> amixer -c 1 sset 'Left Mixer' on
>>> amixer -c 1 sset 'Right Mixer' on
>>>
>>> # raise volume
>>>
>>> amixer -c 1 sset 'Output 2' 36
>>>
>>>
>>> If these settings can be embedded into device tree, and set by kernel as
>>> initial ALSA path settings,
>>>
>>> user can hear the sound with zero ALSA config. That'll be great.
>>>
>>>
>>> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
>>>> +
>>>> + es8388-sound {
>>>> + compatible = "simple-audio-card";
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&hp_det_pin>;
>>>> + simple-audio-card,name = "rockchip,es8388-codec";
> and I guess you'd want a more specific name as that config likely is board-specific
> not for all boards using the es8388-codec?
>
>
> Heiko
>
I got what you mean now. It should be renamed to a board-specific card
name if using Alsa UCM profile, right ?
--
Best Regards!
Levin Du
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 27+ messages in thread* Re: [PATCH v0 2/2] arm64: dts: rockchip: add support for Firefly ROC-RK3399-PC-PLUS
@ 2021-06-30 6:49 ` Levin
0 siblings, 0 replies; 27+ messages in thread
From: Levin @ 2021-06-30 6:49 UTC (permalink / raw)
To: Heiko Stübner, linux-rockchip
Cc: Wayne Chou, Kongxin Deng, Chen-Yu Tsai, Jagan Teki, Jensen Huang,
Johan Jonker, Liang Chen, Marty Jones, Rob Herring,
Uwe Kleine-König, devicetree, linux-arm-kernel,
linux-kernel
Hi Heiko,
Thanks for your reply.
On 2021-06-29 5:32 PM, Heiko Stübner wrote:
> Am Dienstag, 29. Juni 2021, 11:30:10 CEST schrieb Heiko Stübner:
>> Hi Levin,
>>
>> Am Dienstag, 29. Juni 2021, 11:15:59 CEST schrieb Levin:
>>> Hi all, is it possible to turn on some codec mixer switch in the device
>>> tree?
>> I don't think that is appropriate and/or/ possible in the devicetree.
>>
>> Instead I think you want an Alsa UCM profile for it, see:
>> https://github.com/alsa-project/alsa-ucm-conf/tree/master/ucm2/Rockchip
>>
Alsa UCM profile is a complete solution, yet it requires more labor work
of adding a complex profile with all the controls.
The problem is, music/video player knows nothing of the mixers. And with
currently codec driver setting, user cannot
hear any sound until he turns on two mixer switch.
I hope to have a "simple-audio-card,switch" property here.
>>>
>>> Currently, to hear to sound, we need to run the following commands from
>>> the user space:
>>>
>>> # turn on mixer switch
>>>
>>> amixer -c 1 sset 'Left Mixer' on
>>> amixer -c 1 sset 'Right Mixer' on
>>>
>>> # raise volume
>>>
>>> amixer -c 1 sset 'Output 2' 36
>>>
>>>
>>> If these settings can be embedded into device tree, and set by kernel as
>>> initial ALSA path settings,
>>>
>>> user can hear the sound with zero ALSA config. That'll be great.
>>>
>>>
>>> On 2021-06-28 11:54 AM, djw@t-chip.com.cn wrote:
>>>> +
>>>> + es8388-sound {
>>>> + compatible = "simple-audio-card";
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&hp_det_pin>;
>>>> + simple-audio-card,name = "rockchip,es8388-codec";
> and I guess you'd want a more specific name as that config likely is board-specific
> not for all boards using the es8388-codec?
>
>
> Heiko
>
I got what you mean now. It should be renamed to a board-specific card
name if using Alsa UCM profile, right ?
--
Best Regards!
Levin Du
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 27+ messages in thread