[PATCH] ARM: dts: ixp4xx: Add Arcom Vulcan device tree

[PATCH] ARM: dts: ixp4xx: Add Arcom Vulcan device tree

[Linus Walleij]

This adds a device tree for the Arcom Vulcan IXP42x board.

Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/intel-ixp42x-arcom-vulcan.dts    | 167 ++++++++++++++++++
 2 files changed, 168 insertions(+)
 create mode 100644 arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 863347b6b65e..9bf4225c19c9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -242,6 +242,7 @@ dtb-$(CONFIG_ARCH_INTEGRATOR) += \
 dtb-$(CONFIG_ARCH_IXP4XX) += \
 	intel-ixp42x-linksys-nslu2.dtb \
 	intel-ixp42x-welltech-epbx100.dtb \
+	intel-ixp42x-arcom-vulcan.dtb \
 	intel-ixp43x-gateworks-gw2358.dtb
 dtb-$(CONFIG_ARCH_KEYSTONE) += \
 	keystone-k2hk-evm.dtb \
diff --git a/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts
new file mode 100644
index 000000000000..2b254bd34282
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Arcom/Eurotech Vulcan board.
+ * This board is a single board computer in the PC/104 form factor based on
+ * IXP425, and was released around 2005. It previously had the name "Mercury".
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Arcom/Eurotech Vulcan";
+	compatible = "arcom,vulcan", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* CHECKME: 64 MB SDRAM - based on dma zone in boardfile */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		/* CHECKME: using a harddrive at /dev/sda1 as rootfs by default */
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	};
+
+	soc {
+		bus@50000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 32 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0 and CS1
+				 */
+				reg = <0 0x00000000 0x2000000>;
+
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <3>;
+				intel,ixp4xx-eb-byte-access-on-halfword;
+				intel,ixp4xx-eb-write-enable;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* CHECKME: FIS eraseblock at 0x1fe0000? */
+					fis-index-block = <0xff>;
+				};
+			};
+			sram@2,0 {
+				/* 256 KB SDRAM memory at CS2 */
+				compatible = "shared-dma-pool";
+				device_type = "memory";
+				reg = <1 0x00000000 0x40000>;
+				no-map;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <1>;
+				intel,ixp4xx-eb-t4 = <2>;
+				intel,ixp4xx-eb-ahb-split-transfers;
+				intel,ixp4xx-eb-write-enable;
+				intel,ixp4xx-eb-byte-access;
+			};
+			serial@3,0 {
+				/*
+				 * 8250-compatible Exar XR16L2551 2 x UART
+				 *
+				 * CHECKME: if special tweaks are needed, then fix the
+				 * operating system to handle it.
+				 */
+				compatible = "exar,xr16l2551", "ns8250";
+				reg = <3 0x00000000 0x10>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				clock-frequency = <1843200>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <3>;
+				intel,ixp4xx-eb-cycle-type = <1>; /* Motorola cycles */
+				intel,ixp4xx-eb-write-enable;
+				intel,ixp4xx-eb-byte-access;
+			};
+			gpio1: gpio@4,0 {
+				/*
+				 * MMIO GPIO in one byte
+				 */
+				compatible = "arcom,vulcan-gpio";
+				reg = <4 0x00000000 0x1>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable;
+				intel,ixp4xx-eb-byte-access;
+			};
+			watchdog@5,0 {
+				compatible = "maxim,max6369";
+				reg = <5 0x00000000 0x1>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable;
+				intel,ixp4xx-eb-byte-access;
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from Vulcan PCI boardfile.
+			 *
+			 * We have 2 slots (IDSEL) 1 and 2 with one dedicated interrupt
+			 * per slot. This interrupt is shared (OR:ed) by all four pins.
+			 *
+			 * CHECKME: is the interrupt setup on Vulcan really this cheap?
+			 */
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 2 3>, /* INT A on slot 1 is irq 2 */
+			<0x0800 0 0 2 &gpio0 2 3>, /* INT B on slot 1 is irq 2 */
+			<0x0800 0 0 3 &gpio0 2 3>, /* INT C on slot 1 is irq 2 */
+			<0x0800 0 0 4 &gpio0 2 3>, /* INT D on slot 1 is irq 2 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 3 3>, /* INT A on slot 2 is irq 3 */
+			<0x1000 0 0 2 &gpio0 3 3>, /* INT B on slot 2 is irq 3 */
+			<0x1000 0 0 3 &gpio0 3 3>, /* INT C on slot 2 is irq 3 */
+			<0x1000 0 0 4 &gpio0 3 3>; /* INT D on slot 2 is irq 3 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <1>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "ok";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel