* [PATCH] ARM: dts: ux500: Add a device tree for Kyle
@ 2021-07-30 9:31 Linus Walleij
0 siblings, 0 replies; only message in thread
From: Linus Walleij @ 2021-07-30 9:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Linus Walleij, newbyte, Stephan Gerhold
This adds a basic device tree for the Samsung SGH-I407
mobile phone also known as Kyle.
Cc: newbyte@disroot.org
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/ste-ux500-samsung-kyle.dts | 664 +++++++++++++++++++
2 files changed, 666 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30acc6be64b0..ff82567e1664 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1302,7 +1302,8 @@ dtb-$(CONFIG_ARCH_U8500) += \
ste-ux500-samsung-janice.dtb \
ste-ux500-samsung-gavini.dtb \
ste-ux500-samsung-codina.dtb \
- ste-ux500-samsung-skomer.dtb
+ ste-ux500-samsung-skomer.dtb \
+ ste-ux500-samsung-kyle.dtb
dtb-$(CONFIG_ARCH_UNIPHIER) += \
uniphier-ld4-ref.dtb \
uniphier-ld6b-ref.dtb \
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts b/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
new file mode 100644
index 000000000000..3b825666d302
--- /dev/null
+++ b/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
@@ -0,0 +1,664 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Amp SGH-I407 also known as Kyle.
+ *
+ * The code also refers to "Kyle AT&T" reflecting that this mobile phone
+ * was customized for the AT&T subsidiary Aio Wireless (All In One) and
+ * offered by the company in 2013.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Samsung Galaxy Amp (SGH-I407)";
+ compatible = "samsung,kyle", "st-ericsson,u8500";
+
+ chosen {
+ stdout-path = &serial2;
+ };
+
+ /* TI TXS0206 level translator for 2.9 V */
+ sd_level_translator: regulator-gpio {
+ compatible = "regulator-fixed";
+
+ /* GPIO87 EN */
+ gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ regulator-name = "sd-level-translator";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+
+ startup-delay-us = <200>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_level_translator_default>;
+ };
+
+ /* External LDO MIC5366-3.3YMT for eMMC */
+ ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "en-3v3-fixed-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <5000>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_ldo_en_default_mode>;
+ };
+
+ /*
+ * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+ * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+ */
+ lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+ compatible = "regulator-fixed";
+ /* Supplied in turn by VBAT */
+ regulator-name = "VREG_LCD_3V0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ /* GPIO219 controls this regulator */
+ gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pwr_en_default_mode>;
+ };
+ lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+ compatible = "regulator-fixed";
+ /* Supplied in turn by VBAT */
+ regulator-name = "VREG_LCD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ /* GPIO219 controls this regulator too */
+ gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pwr_en_default_mode>;
+ };
+
+ wlan_en: regulator-gpio-wlan-en {
+ compatible = "regulator-fixed";
+ regulator-name = "wl-reg-on";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ startup-delay-us = <200000>;
+ /* GPIO215 WLAN_EN */
+ gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_en_default_mode>;
+ };
+
+ vibrator {
+ compatible = "gpio-vibrator";
+ enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vibrator_default>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_default_mode>;
+
+ button-home {
+ linux,code = <KEY_HOME>;
+ label = "HOME";
+ /* GPIO91 */
+ gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+ };
+ button-volup {
+ linux,code = <KEY_VOLUMEUP>;
+ label = "VOL+";
+ /* GPIO67 */
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ };
+ button-voldown {
+ linux,code = <KEY_VOLUMEDOWN>;
+ label = "VOL-";
+ /* GPIO92 */
+ gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ ktd253: backlight {
+ compatible = "kinetic,ktd253";
+ /* GPIO 69 */
+ enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+ /* Default to 13/32 brightness */
+ default-brightness = <13>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_backlight_default_mode>;
+ };
+
+ /* Richtek RT8515GQW Flash LED Driver IC */
+ flash {
+ compatible = "richtek,rt8515";
+ /* GPIO 140 */
+ enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+ /* GPIO 141 */
+ ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+ /*
+ * RFS is 16 kOhm and RTS is 100 kOhm giving
+ * the flash max current 343mA and torch max
+ * current 55 mA.
+ */
+ richtek,rfs-ohms = <16000>;
+ richtek,rts-ohms = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_flash_default_mode>;
+
+ led {
+ function = LED_FUNCTION_FLASH;
+ color = <LED_COLOR_ID_WHITE>;
+ flash-max-timeout-us = <250000>;
+ flash-max-microamp = <343750>;
+ led-max-microamp = <55000>;
+ };
+ };
+
+ i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_gpio_0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* TODO: this should be used by the NCP6914 Camera power management unit */
+ };
+
+ i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_gpio_1_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ magnetometer@c {
+ compatible = "alps,hscdtd008a";
+ reg = <0x0c>;
+ avdd-supply = <&ab8500_ldo_aux1_reg>;
+ dvdd-supply = <&ab8500_ldo_aux6_reg>;
+ };
+ };
+
+ soc {
+ // External Micro SD slot
+ mmc@80126000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ st,sig-pin-fbclk;
+ full-pwr-cycle;
+ vmmc-supply = <&ab8500_ldo_aux3_reg>;
+ vqmmc-supply = <&sd_level_translator>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mc0_a_1_default>;
+ pinctrl-1 = <&mc0_a_1_sleep>;
+ cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+ status = "okay";
+ };
+
+ // WLAN SDIO channel
+ mmc@80118000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ non-removable;
+ cap-sd-highspeed;
+ vmmc-supply = <&wlan_en>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mc1_a_2_default>;
+ pinctrl-1 = <&mc1_a_2_sleep>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@1 {
+ compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ /* GPIO216 WL_HOST_WAKE */
+ interrupt-parent = <&gpio6>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_default_mode>;
+ };
+ };
+
+ /*
+ * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
+ */
+ mmc@80005000 {
+ arm,primecell-periphid = <0x10480180>;
+ max-frequency = <100000000>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ no-sdio;
+ no-sd;
+ /* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
+ post-power-on-delay-ms = <300>;
+ vmmc-supply = <&ldo_3v3_reg>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mc2_a_1_default>;
+ pinctrl-1 = <&mc2_a_1_sleep>;
+
+ status = "okay";
+ };
+
+ /* GBF (Bluetooth) UART */
+ uart@80120000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&u0_a_1_default>;
+ pinctrl-1 = <&u0_a_1_sleep>;
+ status = "okay";
+
+ bluetooth {
+ /* BCM4334B0 actually */
+ compatible = "brcm,bcm4330-bt";
+ shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bluetooth_default_mode>;
+ };
+ };
+
+ /* GPF UART */
+ uart@80121000 {
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+ pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+ };
+
+ /* Debugging console UART connected to AB8505 USB */
+ uart@80007000 {
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&u2rxtx_c_1_default>;
+ pinctrl-1 = <&u2rxtx_c_1_sleep>;
+ };
+
+ prcmu@80157000 {
+ ab8505 {
+ ab8500_usb {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&usb_a_1_default>;
+ pinctrl-1 = <&usb_a_1_sleep>;
+ };
+
+ ab8505-regulators {
+ ab8500_ldo_aux1 {
+ /* Used for VDD for sensors */
+ regulator-name = "AUX1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ab8500_ldo_aux2 {
+ /* Supplies the MMS touchscreen only with 3.3V */
+ regulator-name = "AUX2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ab8500_ldo_aux3 {
+ /* Used for voltage for external MMC/SD card */
+ regulator-name = "AUX3";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ab8500_ldo_aux4 {
+ regulator-name = "AUX4";
+ /* Hammer to 3.3V for the touchscreen */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ab8500_ldo_aux5 {
+ regulator-name = "AUX5";
+ /* 1.8V for the touchscreen */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ab8500_ldo_aux6 {
+ regulator-name = "AUX6";
+ /* Used by sensors for 1.8 V in R0.1+ */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ab8500_ldo_aux8 {
+ /* Unused */
+ regulator-name = "AUX8";
+ };
+ };
+ };
+ };
+
+ /* I2C0 */
+ i2c@80004000 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c0_a_1_default>;
+ pinctrl-1 = <&i2c0_a_1_sleep>;
+
+ proximity@44 {
+ compatible = "sharp,gp2ap002s00f";
+ clock-frequency = <400000>;
+ reg = <0x44>;
+
+ interrupt-parent = <&gpio4>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ vio-supply = <&ab8500_ldo_aux6_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gp2ap002_kyle_default>;
+ sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
+ sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+ };
+ };
+
+ /* I2C2 */
+ i2c@80128000 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c2_b_2_default>;
+ pinctrl-1 = <&i2c2_b_2_sleep>;
+
+ accel@18 {
+ compatible = "bosch,bma254";
+ clock-frequency = <400000>;
+ reg = <0x18>;
+
+ mount-matrix = "-1", "0", "0",
+ "0", "-1", "0",
+ "0", "0", "-1";
+ vdd-supply = <&ab8500_ldo_aux1_reg>;
+ vddio-supply = <&ab8500_ldo_aux6_reg>;
+ };
+ };
+
+ /* I2C3 */
+ i2c@80110000 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c3_c_2_default>;
+ pinctrl-1 = <&i2c3_c_2_sleep>;
+
+ /* Melfas MMS134S touchscreen */
+ touchscreen@48 {
+ compatible = "melfas,mms134s";
+ reg = <0x48>;
+ /* GPIO218 for IRQ */
+ interrupt-parent = <&gpio6>;
+ interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+ /* AVDD is "analog supply", 2.57-3.47 V */
+ avdd-supply = <&ab8500_ldo_aux2_reg>;
+ /* VDD is "digital supply" 1.71-3.47V */
+ vdd-supply = <&ab8500_ldo_aux5_reg>;
+
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mms134s_kyle_default>;
+ };
+ };
+
+ mcde@a0350000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dsi_default_mode>;
+
+ dsi@a0351000 {
+ panel {
+ /*
+ * NT35510-based Hydis HVA40WV1
+ * Apparently some Kyle models can have a NT35512 fitted
+ * here instead. In that case the boot loader needs to
+ * modify this compatible.
+ */
+ compatible = "hydis,hva40wv1", "novatek,nt35510";
+ reg = <0>;
+ /* v_lcd_3v0 2.3-4.8V */
+ vdd-supply = <&lcd_3v0_reg>;
+ /* v_lcd_1v8 1.65-3.3V */
+ vddi-supply = <&lcd_1v8_reg>;
+ /* GPIO 139 */
+ reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&display_default_mode>;
+ backlight = <&ktd253>;
+ };
+ };
+ };
+ };
+};
+
+&pinctrl {
+ /*
+ * This extends the MC0_A_1 default config to include
+ * the card detect GPIO217 line.
+ */
+ sdi0 {
+ mc0_a_1_default {
+ default_cfg1 {
+ /* GPIO18, 19 & 20 unused so pull down */
+ ste,config = <&gpio_in_pd>;
+ };
+ default_cfg4 {
+ pins = "GPIO217_AH12"; /* card detect */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+
+ mcde {
+ dsi_default_mode: dsi_default {
+ default_mux1 {
+ /* Mux in VSI0 used for DSI TE */
+ function = "lcd";
+ groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
+ };
+ default_cfg1 {
+ pins = "GPIO68_E1"; /* VSI0 */
+ ste,config = <&in_nopull>;
+ };
+ };
+ };
+
+ /* Two GPIO lines used by the display */
+ display {
+ display_default_mode: display_default {
+ kyle_cfg1 {
+ /*
+ * OLED DETECT or check_pba, this appears to be high
+ * on "PBA" which I guess is "prototype board A".
+ */
+ pins = "GPIO93_B7";
+ ste,config = <&gpio_in_nopull>;
+ };
+ kyle_cfg2 {
+ pins = "GPIO139_C9";
+ /*
+ * MIPI_DSI0_RESET_N resets the display, leave high
+ * (de-asserted) so we only assert reset explicitly
+ * from the display driver.
+ */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+
+ /* GPIO that enables the LDO regulator for the LCD display */
+ lcd-ldo {
+ lcd_pwr_en_default_mode: lcd_pwr_en_default {
+ /* LCD_PWR_EN on GPIO219 */
+ kyle_cfg1 {
+ pins = "GPIO219_AG10";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+
+ backlight {
+ gpio_backlight_default_mode: backlight_default {
+ kyle_cfg1 {
+ pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ flash {
+ gpio_flash_default_mode: flash_default {
+ kyle_cfg1 {
+ pins = "GPIO140_B11", "GPIO141_C12";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ /* GPIO that enables the 2.9V SD card level translator */
+ sd-level-translator {
+ sd_level_translator_default: sd_level_translator_default {
+ /* level shifter on GPIO87 */
+ kyle_cfg1 {
+ pins = "GPIO87_B3";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ /* GPIO that enables the LDO regulator for the eMMC */
+ emmc-ldo {
+ emmc_ldo_en_default_mode: emmc_ldo_default {
+ /* LDO enable on GPIO223 */
+ kyle_cfg1 {
+ pins = "GPIO223_AH9";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ /* GPIO keys */
+ gpio-keys {
+ gpio_keys_default_mode: gpio_keys_default {
+ kyle_cfg1 {
+ pins = "GPIO67_G2", /* VOL UP */
+ "GPIO91_B6", /* HOME */
+ "GPIO92_D6"; /* VOL DOWN */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ /* Interrupt line for light/proximity sensor GP2AP002 */
+ gp2ap002 {
+ gp2ap002_kyle_default: gp2ap002_kyle {
+ kyle_cfg1 {
+ pins = "GPIO146_D13";
+ ste,config = <&gpio_in_nopull>;
+ };
+ };
+ };
+ /* GPIO-based I2C bus for NCP6914 */
+ i2c-gpio-0 {
+ i2c_gpio_0_default: i2c_gpio_0 {
+ kyle_cfg1 {
+ pins = "GPIO143_D12", "GPIO144_B13";
+ ste,config = <&gpio_in_nopull>;
+ };
+ };
+ };
+ /* GPIO-based I2C bus for ALPS HSCD compass */
+ i2c-gpio-1 {
+ i2c_gpio_1_default: i2c_gpio_1 {
+ kyle_cfg1 {
+ pins = "GPIO151_B17", "GPIO152_D16";
+ ste,config = <&gpio_in_nopull>;
+ };
+ };
+ };
+ wlan {
+ wlan_default_mode: wlan_default {
+ kyle_cfg1 {
+ pins = "GPIO216_AG12";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ wlan_en_default_mode: wlan_en_default {
+ kyle_cfg2 {
+ pins = "GPIO215_AH13";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ bluetooth {
+ bluetooth_default_mode: bluetooth_default {
+ kyle_cfg1 {
+ pins = "GPIO199_AH23", "GPIO222_AJ9";
+ ste,config = <&gpio_out_lo>;
+ };
+ kyle_cfg2 {
+ pins = "GPIO97_D9";
+ ste,config = <&gpio_in_nopull>;
+ };
+ };
+ };
+ vibrator {
+ vibrator_default: vibrator_default {
+ kyle_cfg1 {
+ pins = "GPIO195_AG28"; /* MOT_EN */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ /* Interrupt line for the Melfas MMS134S touchscreen */
+ touchscreen {
+ mms134s_kyle_default: mms134s_kyle {
+ kyle_cfg1 {
+ pins = "GPIO218_AH11";
+ ste,config = <&gpio_in_nopull>;
+ };
+ };
+ };
+};
+
+&ab8505_gpio {
+ /* Hog a few default settings */
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_default>;
+
+ gpio {
+ gpio_default: gpio_default {
+ kyle_mux {
+ /* Change unused pins to GPIO mode */
+ function = "gpio";
+ groups = "gpio3_a_1", /* default: SysClkReq4 */
+ "gpio14_a_1"; /* default: PWMOut1 */
+ };
+ kyle_cfg1 {
+ pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+ bias-disable;
+ };
+ };
+ };
+};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2021-07-30 9:37 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-30 9:31 [PATCH] ARM: dts: ux500: Add a device tree for Kyle Linus Walleij
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.